Some Arizona devices have a hardware ANC block present. This patch adds
the registers necessary to configure this hardware block.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The type of the data for the main Arizona IRQ chip should be struct
arizona not struct regmap_irq_chip_data. The bug is harmless but should
probably be corrected anyway.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver always checks for pdata being NULL except in one place.
Add a check to prevent a possible NULL pointer deference error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.
One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
ACOKB goes high.
On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).
The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are already helper functions to do 64-bit I/O on 32-bit machines, thus we
don't need to reinvent the wheel. In our case we can't use readq() / writeq()
even on 64-bit kernel since there is a hardware limitation (OCP bus is a 32-bit
bus).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Introduced by:
commit 8019ff6cfc ("regmap: Use reg_sequence for multi_reg_write / register_patch")
Interacting with:
commit 561629755a21 ("mfd: arizona: Add support for WM8998 and WM1814")
commit 81207880ce ("mfd: wm5110: Add register patch for rev E and above")
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STMPE2401 and STMPE2401 altfunction 1 corresponds to the
PWM channels. This oneliner was missing in the case-switch, making
it impossible to enable the PWM channel output.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
added clock handling for the 32k clock from palmas-clk. However, that
patch did not consider a typical situation where twl6040 is built-in,
and palmas-clk is a loadable module like we have in omap2plus_defconfig.
If palmas-clk is not loaded before twl6040 probes, we will get a
"clk32k is not handled" warning during booting. This means that any
drivers relying on this clock will mysteriously fail, including
omap5-uevm WLAN and audio.
Note that for WLAN, we probably should also eventually get
the clk32kgaudio for MMC3 directly as that's shared between
audio and WLAN SDIO at least for omap5-uevm. It seems the
WLAN chip cannot get it as otherwise MMC3 won't get properly
probed.
Fixes: 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add chip identification support for 88PM860 device
to the pm80x_chip_mapping table.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Documentation/devicetree/bindings/mfd/cros-ec.txt DT binding doc lists
"google,cros-ec-i2c" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the I2C
core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a 24c08 chip connected to i2c bus on Intel Galileo Gen2 board. Enable
it via ACPI ID INT3499.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel Galileo Gen2 the GPIO expanders are connected to the i2c bus. For
those devices the ACPI table has specific parameters that refer to an actual
i2c host controller. Since MFD now copes with that specific configuration we
have to provide a necessary information how to distinguish devices in ACPI
namespace. Here the _ADR values are provided.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel Galileo boards the GPIO expander is connected to i2c bus. Moreover it
is able to generate interrupt, but interrupt line is connected to GPIO. That's
why we have to have GPIO driver in place when we will probe i2c host with
device connected to it.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is at least one board on the market, i.e. Intel Galileo Gen2, that uses
_ADR to distinguish the devices under one actual device. Due to this we have to
improve the quirk in the MFD core to handle that board.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When referencing other DT bindings documentation, use relative
path rather than absolute.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds power supply driver support for the Fuel-Gauge part of
the DA9150 combined Charger and Fuel-Gauge device.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch modifies tps6105x and associated function driver to use regmap
instead of operating directly on i2c.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
Two tagged for -stable
One is really a cleanup to match and improve kmemcache interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yqg5
-----END PGP SIGNATURE-----
Merge tag 'md/4.3-fixes' of git://neil.brown.name/md
Pull md fixes from Neil Brown:
"Assorted fixes for md in 4.3-rc.
Two tagged for -stable, and one is really a cleanup to match and
improve kmemcache interface.
* tag 'md/4.3-fixes' of git://neil.brown.name/md:
md/bitmap: don't pass -1 to bitmap_storage_alloc.
md/raid1: Avoid raid1 resync getting stuck
md: drop null test before destroy functions
md: clear CHANGE_PENDING in readonly array
md/raid0: apply base queue limits *before* disk_stack_limits
md/raid5: don't index beyond end of array in need_this_block().
raid5: update analysis state for failed stripe
md: wait for pending superblock updates before switching to read-only
Pull MIPS updates from Ralf Baechle:
"This week's round of MIPS fixes:
- Fix JZ4740 build
- Fix fallback to GFP_DMA
- FP seccomp in case of ENOSYS
- Fix bootmem panic
- A number of FP and CPS fixes
- Wire up new syscalls
- Make sure BPF assembler objects can properly be disassembled
- Fix BPF assembler code for MIPS I"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: scall: Always run the seccomp syscall filters
MIPS: Octeon: Fix kernel panic on startup from memory corruption
MIPS: Fix R2300 FP context switch handling
MIPS: Fix octeon FP context switch handling
MIPS: BPF: Fix load delay slots.
MIPS: BPF: Do all exports of symbols with FEXPORT().
MIPS: Fix the build on jz4740 after removing the custom gpio.h
MIPS: CPS: #ifdef on CONFIG_MIPS_MT_SMP rather than CONFIG_MIPS_MT
MIPS: CPS: Don't include MT code in non-MT kernels.
MIPS: CPS: Stop dangling delay slot from has_mt.
MIPS: dma-default: Fix 32-bit fall back to GFP_DMA
MIPS: Wire up userfaultfd and membarrier syscalls.
Pull irq fixes from Thomas Gleixner:
"This update contains:
- Fix for a long standing race affecting /proc/irq/NNN
- One line fix for ARM GICV3-ITS counting the wrong data
- Warning silencing in ARM GICV3-ITS. Another GCC trying to be
overly clever issue"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Count additional LPIs for the aliased devices
irqchip/gic-v3-its: Silence warning when its_lpi_alloc_chunks gets inlined
genirq: Fix race in register_irq_proc()
The MIPS syscall handler code used to return -ENOSYS on invalid
syscalls. Whilst this is expected, it caused problems for seccomp
filters because the said filters never had the change to run since
the code returned -ENOSYS before triggering them. This caused
problems on the chromium testsuite for filters looking for invalid
syscalls. This has now changed and the seccomp filters are always
run even if the syscall is invalid. We return -ENOSYS once we
return from the seccomp filters. Moreover, similar codepaths have
been merged in the process which simplifies somewhat the overall
syscall code.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11236/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull x86 fixes from Ingo Molnar:
"Fixes all around the map: W+X kernel mapping fix, WCHAN fixes, two
build failure fixes for corner case configs, x32 header fix and a
speling fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers/uapi: Fix __BITS_PER_LONG value for x32 builds
x86/mm: Set NX on gap between __ex_table and rodata
x86/kexec: Fix kexec crash in syscall kexec_file_load()
x86/process: Unify 32bit and 64bit implementations of get_wchan()
x86/process: Add proper bound checks in 64bit get_wchan()
x86, efi, kasan: Fix build failure on !KASAN && KMEMCHECK=y kernels
x86/hyperv: Fix the build in the !CONFIG_KEXEC_CORE case
x86/cpufeatures: Correct spelling of the HWP_NOTIFY flag
Pull EFI fixes from Ingo Molnar:
"Two EFI fixes: one for x86, one for ARM, fixing a boot crash bug that
can trigger under newer EFI firmware"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64/efi: Fix boot crash by not padding between EFI_MEMORY_RUNTIME regions
x86/efi: Fix boot crash by mapping EFI memmap entries bottom-up at runtime, instead of top-down
Pull drm fixes from Dave Airlie:
"Bunch of fixes all over the place, all pretty small: amdgpu, i915,
exynos, one qxl and one vmwgfx.
There is also a bunch of mst fixes, I left some cleanups in the series
as I didn't think it was worth splitting up the tested series"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits)
drm/dp/mst: add some defines for logical/physical ports
drm/dp/mst: drop cancel work sync in the mstb destroy path (v2)
drm/dp/mst: split connector registration into two parts (v2)
drm/dp/mst: update the link_address_sent before sending the link address (v3)
drm/dp/mst: fixup handling hotplug on port removal.
drm/dp/mst: don't pass port into the path builder function
drm/radeon: drop radeon_fb_helper_set_par
drm: handle cursor_set2 in restore_fbdev_mode
drm/exynos: Staticize local function in exynos_drm_gem.c
drm/exynos: fimd: actually disable dp clock
drm/exynos: dp: remove suspend/resume functions
drm/qxl: recreate the primary surface when the bo is not primary
drm/amdgpu: only print meaningful VM faults
drm/amdgpu/cgs: remove import_gpu_mem
drm/i915: Call non-locking version of drm_kms_helper_poll_enable(), v2
drm: Add a non-locking version of drm_kms_helper_poll_enable(), v2
drm/vmwgfx: Fix a command submission hang regression
drm/exynos: remove unused mode_fixup() code
drm/exynos: remove decon_mode_fixup()
drm/exynos: remove fimd_mode_fixup()
...
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
This patch fixes one cases where abs() was being used with 64-bit
nanosecond values, where the result may be capped at 32-bits.
This potentially could cause watchdog false negatives on 32-bit
systems, so this patch addresses the issue by using abs64().
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AJCF
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix for transparent huge page change_protection() logic which was
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: fix function_graph tracer panic
arm64: Fix THP protection change logic
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- Fix for accidental modification of arguments of syscall functions
- Wire up new syscalls
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.3-rc1
m68k: Define asmlinkage_protect
m68k: Wire up membarrier
m68k: Wire up userfaultfd
m68k: Wire up direct socket calls
When configuring the interrupt mapping for a new device, we
iterate over all the possible aliases to account for their
maximum MSI allocation. This was introduced by e8137f4f50
("irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration").
Turns out that the code doing that is a bit braindead, and repeatedly
accounts for the same device over and over.
Fix this by counting the actual alias that is passed to us by the
core code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
More agressive inlining in recent versions of GCC have uncovered
a new set of warnings:
drivers/irqchip/irq-gic-v3-its.c: In function its_msi_prepare:
drivers/irqchip/irq-gic-v3-its.c:1148:26: warning: lpi_base may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.lpi_base = lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1116:6: note: lpi_base was declared here
int lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1149:25: warning: nr_lpis may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.nr_lpis = nr_lpis;
^
drivers/irqchip/irq-gic-v3-its.c:1117:6: note: nr_lpis was declared here
int nr_lpis;
^
The warning is fairly benign (there is no code path that could
actually use uninitialized variables), but let's silence it anyway
by zeroing the variables on the error path.
Reported-by: Alex Shi <alex.shi@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This contains fixes spread throughout the drivers
Also fixes one more instance of privatecnt in dmaengine
bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
odd fixes in xgene, idma, sun4i and zxdma
at_xdmac fixes for cleaning descriptor and block addr mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wcjo
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This contains fixes spread throughout the drivers, and also fixes one
more instance of privatecnt in dmaengine.
Driver fixes summary:
- bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
- odd fixes in xgene, idma, sun4i and zxdma
- at_xdmac fixes for cleaning descriptor and block addr mode"
* tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pxa_dma: fix residue corner case
dmaengine: pxa_dma: fix the no-requestor case
dmaengine: zxdma: Fix off-by-one for testing valid pchan request
dmaengine: at_xdmac: clean used descriptor
dmaengine: at_xdmac: change block increment addressing mode
dmaengine: dw: properly read DWC_PARAMS register
dmaengine: xgene-dma: Fix overwritting DMA tx ring
dmaengine: fix balance of privatecnt
dmaengine: sun4i: fix unsafe list iteration
dmaengine: idma64: improve residue estimation
dmaengine: xgene-dma: fix handling xgene_dma_get_ring_size result
dmaengine: pxa_dma: fix initial list move
Pull block fixes from Jens Axboe:
"Another week, another round of fixes.
These have been brewing for a bit and in various iterations, but I
feel pretty comfortable about the quality of them. They fix real
issues. The pull request is mostly blk-mq related, and the only one
not fixing a real bug, is the tag iterator abstraction from Christoph.
But it's pretty trivial, and we'll need it for another fix soon.
Apart from the blk-mq fixes, there's an NVMe affinity fix from Keith,
and a single fix for xen-blkback from Roger fixing failure to free
requests on disconnect"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: factor out a helper to iterate all tags for a request_queue
blk-mq: fix racy updates of rq->errors
blk-mq: fix deadlock when reading cpu_list
blk-mq: avoid inserting requests before establishing new mapping
blk-mq: fix q->mq_usage_counter access race
blk-mq: Fix use after of free q->mq_map
blk-mq: fix sysfs registration/unregistration race
blk-mq: avoid setting hctx->tags->cpumask before allocation
NVMe: Set affinity after allocating request queues
xen/blkback: free requests on disconnection
This reverts commit e51e38494a: we
actually do want the device to work in extended W mode, as this is the
mode that allows us receiving multiple contact information.
Cc: stable@vger.kernel.org
During development it was found that a number of builds would panic
during the kernel init process, more specifically in 'delayed_fput()'.
The panic showed the kernel trying to access a memory address of
'0xb7fdc00' while traversing the 'delayed_fput_list' structure.
Comparing this memory address to the value of the pointer used on
builds that did not panic confirmed that the pointer on crashing
builds must have been corrupted at some stage earlier in the init
process.
By traversing the list earlier and earlier in the code it was found
that 'plat_mem_setup()' was responsible for corrupting the list.
Specifically the line:
memory = cvmx_bootmem_phy_alloc(mem_alloc_size,
__pa_symbol(&__init_end), -1,
0x100000,
CVMX_BOOTMEM_FLAG_NO_LOCKING);
Which would eventually call:
cvmx_bootmem_phy_set_size(new_ent_addr,
cvmx_bootmem_phy_get_size
(ent_addr) -
(desired_min_addr -
ent_addr));
Where 'new_ent_addr'=0x4800000 (the address of 'delayed_fput_list')
and the second argument (size)=0xb7fdc00 (the address causing the
kernel panic). The job of this part of 'plat_mem_setup()' is to
allocate chunks of memory for the kernel to use. At the start of
each chunk of memory the size of the chunk is written, hence the
value 0xb7fdc00 is written onto memory at 0x4800000, therefore the
kernel panics when it goes back to access 'delayed_fput_list' later
on in the initialisation process.
On builds that were not crashing it was found that the compiler had
placed 'delayed_fput_list' at 0x4800008, meaning it wasn't corrupted
(but something else in memory was overwritten).
As can be seen in the first function call above the code begins to
allocate chunks of memory beginning from the symbol '__init_end'.
The MIPS linker script (vmlinux.lds.S) however defines the .bss
section to begin after '__init_end'. Therefore memory within the
.bss section is allocated to the kernel to use (System.map shows
'delayed_fput_list' and other kernel structures to be in .bss).
To stop the kernel panic (and the .bss section being corrupted)
memory should begin being allocated from the symbol '_end'.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: aleksey.makarov@auriga.com
Patchwork: https://patchwork.linux-mips.org/patch/11251/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1a3d59579b ("MIPS: Tidy up FPU context switching") removed FP
context saving from the asm-written resume function in favour of reusing
existing code to perform the same task. However it only removed the FP
context saving code from the r4k_switch.S implementation of resume.
Remove it from the r2300_switch.S implementation too in order to prevent
attempting to save the FP context twice, which would likely lead to an
exception from the second save because the FPU had already been disabled
by the first save.
This patch has only been build tested, using rbtx49xx_defconfig.
Fixes: 1a3d59579b ("MIPS: Tidy up FPU context switching")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/11167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Allow users of mmc_of_parse() to succeed when CONFIG_GPIOLIB is unset
- Prevent infinite loop of re-tuning for CRC-errors for CMD19 and CMD21
MMC host:
- pxamci: Fix issues with card detect
- sunxi: Fix clk-delay settings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bo65
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.3 rc4:
MMC core:
- Allow users of mmc_of_parse() to succeed when CONFIG_GPIOLIB is
unset
- Prevent infinite loop of re-tuning for CRC-errors for CMD19 and
CMD21
MMC host:
- pxamci: Fix issues with card detect
- sunxi: Fix clk-delay settings"
* tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: fix dead loop of mmc_retune
mmc: pxamci: fix card detect with slot-gpio API
mmc: sunxi: Fix clk-delay settings
mmc: core: Don't return an error for CD/WP GPIOs when GPIOLIB is unset
Pull IOVA fixes from David Woodhouse:
"The main fix here is the first one, fixing the over-allocation of
size-aligned requests. The other patches simply make the existing
IOVA code available to users other than the Intel VT-d driver, with no
functional change.
I concede the latter really *should* have been submitted during the
merge window, but since it's basically risk-free and people are
waiting to build on top of it and it's my fault I didn't get it in, I
(and they) would be grateful if you'd take it"
* git://git.infradead.org/intel-iommu:
iommu: Make the iova library a module
iommu: iova: Export symbols
iommu: iova: Move iova cache management to the iova library
iommu/iova: Avoid over-allocating when size-aligned
