Driver uses "reply descriptor post queues" in round robin fashion so that
IO's are distributed to all the available reply descriptor post queues
equally. With this each reply descriptor post queue load is balanced.
This is enabled only if CPUs count to MSI-X vector count ratio is X:1
(where X > 1) This improves performance and also fixes soft lockups.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue Description:
We have seen cpu lock up issue from fields if system has greater (more than
96) logical cpu count. SAS3.0 controller (Invader series) supports at max
96 msix vector and SAS3.5 product (Ventura) supports at max 128 msix
vectors.
This may be a generic issue (if PCI device supports completion on multiple
reply queues). Let me explain it w.r.t to mpt3sas supported h/w just to
simplify the problem and possible changes to handle such issues. IT HBA
(mpt3sas) supports multiple reply queues in completion path. Driver creates
MSI-x vectors for controller as "min of (FW supported Reply queue, Logical
CPUs)". If submitter is not interrupted via completion on same CPU, there
is a loop in the IO path. This behavior can cause hard/soft CPU lockups, IO
timeout, system sluggish etc.
Example - one CPU (e.g. CPU A) is busy submitting the IOs and another CPU
(e.g. CPU B) is busy with processing the corresponding IO's reply
descriptors from reply descriptor queue upon receiving the interrupts from
HBA. If the CPU A is continuously pumping the IOs then always CPU B (which
is executing the ISR) will see the valid reply descriptors in the reply
descriptor queue and it will be continuously processing those reply
descriptor in a loop without quitting the ISR handler.
Mpt3sas driver will exit ISR handler if it finds unused reply descriptor in
the reply descriptor queue. Since CPU A will be continuously sending the
IOs, CPU B may always see a valid reply descriptor (posted by HBA Firmware
after processing the IO) in the reply descriptor queue. In worst case,
driver will not quit from this loop in the ISR handler. Eventually, CPU
lockup will be detected by watchdog.
Above mentioned behavior is not common if "rq_affinity" set to 2 or
affinity_hint is honored by irqbalance as "exact". If rq_affinity is set
to 2, submitter will be always interrupted via completion on same CPU. If
irqbalance is using "exact" policy, interrupt will be delivered to
submitter CPU.
If CPU counts to MSI-X vectors (reply descriptor Queues) count ratio is not
1:1, we still have exposure of issue explained above and for that we don't
have any solution.
Exposure of soft/hard lockup if CPU count is more than MSI-x supported by
device.
If CPUs count to MSI-x vectors count ratio is not 1:1, (Other way, if CPU
counts to MSI-x vector count ratio is something like X:1, where X > 1) then
'exact' irqbalance policy OR rq_affinity = 2 won't help to avoid CPU
hard/soft lockups. There won't be any one to one mapping between CPU to
MSI-x vector instead one MSI-x interrupt (or reply descriptor queue) is
shared with group/set of CPUs and there is a possibility of having a loop
in the IO path within that CPU group and may observe lockups.
For example: Consider a system having two NUMA nodes and each node having
four logical CPUs and also consider that number of MSI-x vectors enabled on
the HBA is two, then CPUs count to MSI-x vector count ratio as 4:1. e.g.
MSIx vector 0 is affinity to CPU 0, CPU 1, CPU 2 & CPU 3 of NUMA node 0 and
MSI-x vector 1 is affinity to CPU 4, CPU 5, CPU 6 & CPU 7 of NUMA node 1.
numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 --> MSI-x 0
node 0 size: 65536 MB
node 0 free: 63176 MB
node 1 cpus: 4 5 6 7 -->MSI-x 1
node 1 size: 65536 MB
node 1 free: 63176 MB
Assume that user started an application which uses all the CPUs of NUMA
node 0 for issuing the IOs. Only one CPU from affinity list (it can be any
cpu since this behavior depends upon irqbalance) CPU0 will receive the
interrupts from MSIx vector 0 for all the IOs. Eventually, CPU 0 IO
submission percentage will be decreasing and ISR processing percentage will
be increasing as it is more busy with processing the interrupts. Gradually
IO submission percentage on CPU 0 will be zero and it's ISR processing
percentage will be 100 percentage as IO loop has already formed within the
NUMA node 0, i.e. CPU 1, CPU 2 & CPU 3 will be continuously busy with
submitting the heavy IOs and only CPU 0 is busy in the ISR path as it
always find the valid reply descriptor in the reply descriptor
queue. Eventually, we will observe the hard lockup here.
Chances of occurring of hard/soft lockups are directly proportional to
value of X. If value of X is high, then chances of observing CPU lockups is
high.
Solution: Use IRQ poll interface defined in " irq_poll.c". mpt3sas driver
will execute ISR routine in Softirq context and it will always quit the
loop based on budget provided in IRQ poll interface.
In these scenarios (i.e. where CPUs count to MSI-X vectors count ratio is
X:1 (where X > 1)), IRQ poll interface will avoid CPU hard lockups due to
voluntary exit from the reply queue processing based on budget. Note -
Only one MSI-x vector is busy doing processing.
Irqstat output:
IRQs / 1 second(s)
IRQ# TOTAL NODE0 NODE1 NODE2 NODE3 NAME
44 122871 122871 0 0 0 IR-PCI-MSI-edge mpt3sas0-msix0
45 0 0 0 0 0 IR-PCI-MSI-edge mpt3sas0-msix1
We use this approach only if cpu count is more than FW supported MSI-x
vector
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Separate out processing of reply descriptor post queue from _base_interrupt
to _base_process_reply_queue.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixed typo in request_desript_type.
request_desript_type --> request_descript_type.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warnings by adding the proper missing breaks:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function _base_display_OEMs_branding :
drivers/scsi/mpt3sas/mpt3sas_base.c:3548:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3566:3: note: here
case MPI2_MFGPAGE_DEVID_SAS2308_2:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3567:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3601:3: note: here
case MPI25_MFGPAGE_DEVID_SAS3008:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3735:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3745:3: note: here
case MPI2_MFGPAGE_DEVID_SAS2308_2:
^~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3746:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (ioc->pdev->subsystem_device) {
^~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:3768:3: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With commit 09c2f95ad4 ("scsi: mpt3sas: Swap I/O memory read value back
to cpu endianness"), 64bit writes in _base_writeq() were rewritten to use
__raw_writeq() instad of writeq().
This introduced a bug apparent on powerpc64 systems such as the Raptor
Talos II that causes the HBA to drop from the PCIe bus under heavy load and
being reinitialized after a couple of seconds.
It can easily be triggered on affacted systems by using something like
fio --name=random-write --iodepth=4 --rw=randwrite --bs=4k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
fio --name=random-write --iodepth=4 --rw=randwrite --bs=64k --direct=0 \
--size=128M --numjobs=64 --end_fsync=1
a couple of times. In my case I tested it on both a ZFS raidz2 and a btrfs
raid6 using LSI 9300-8i and 9400-8i controllers.
The fix consists in resembling the write ordering of writeq() by adding a
mandatory write memory barrier before device access and a compiler barrier
afterwards. The additional MMIO barrier is superfluous.
Signed-off-by: Stephan Günther <moepi@moepi.net>
Reported-by: Matt Corallo <linux@bluematt.me>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use ioc->base_readl to restrict the readl retries to only Aero controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes Aero controllers appears to be returning bad data (0) for
doorbell register read and if retries are performed immediately after the
bad read, they return good data.
Workaround is added to retry read from doorbell registers for maximum three
times if driver get the zero. Added functions base_readl_aero for Aero IOC
and base_readl for gen35 and other controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If EEDPTagMode field in manufacturing page11 is set then unset it. This is
needed to fix a hardware bug only in SAS3/SAS2 cards. So, skipping
EEDPTagMode changes in Manufacturing page11 for SAS 3.5 controllers.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Doing code refactor of function
mpt3sas_wait_for_ioc() for better readability.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional changes. This section of code "wait for IOC to be
operational" is used in many places across the driver. Factor this code
out into a new mpt3sas_wait_for_ioc().
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added new #define variable IOC_OPERATIONAL_WAIT_COUNT and it replaces hard
coded value '10' in all the places where driver is waiting for the IOC to
become operational.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Also simplify setting the DMA mask a bit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: warning: equality comparison
with extraneous parentheses [-Wparentheses-equality]
if ((ioc == NULL))
~~~~^~~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: note: remove extraneous
parentheses around the comparison to silence this warning
if ((ioc == NULL))
~ ^ ~
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: note: use '=' to turn this
equality comparison into an assignment
if ((ioc == NULL))
^~
=
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: warning: equality comparison
with extraneous parentheses [-Wparentheses-equality]
if ((pdev == NULL))
~~~~~^~~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: note: remove extraneous
parentheses around the comparison to silence this warning
if ((pdev == NULL))
~ ^ ~
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: note: use '=' to turn this
equality comparison into an assignment
if ((pdev == NULL))
^~
=
2 warnings generated.
Remove them and while we're at it, simplify the NULL checks as '!var' is
used more than 'var == NULL'.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert these uses to ioc_<level> where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Convert the existing 2 uses to make the format and arguments matching more
obvious.
Miscellanea:
o Move the word "enabled" into the format to trivially reduce object size
o Remove unnecessary parentheses
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use a more common logging style.
Done using the perl script below and some typing
$ git grep --name-only -w MPT3SAS_FMT -- "*.c" | \
xargs perl -i -e 'local $/; while (<>) { s/\bpr_(info|err|notice|warn)\s*\(\s*MPT3SAS_FMT\s*("[^"]+"(?:\s*\\?\s*"[^"]+"\s*){0,5}\s*),\s*ioc->name\s*/ioc_\1(ioc, \2/g; print;}'
Miscellanea for these conversions:
o Coalesce formats
o Realign arguments
o Remove unnecessary parentheses
o Use casts to u64 instead of unsigned long long where appropriate
o Convert broken pr_info uses to pr_cont
o Fix broken format string concatenation with line continuations and
excess whitespace
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
Swap the I/O memory read value back to cpu endianness before storing it in
a data structures which are defined in the MPI headers where u8 components
are not defined in the endianness order.
In this area from day one mpt3sas driver is using le32_to_cpu() &
cpu_to_le32() APIs. But in commit cf6bf9710c
(mpt3sas: Bug fix for big endian systems) we have removed these APIs
before reading I/O memory which we should haven't done it. So
in this patch I am correcting it by adding these APIs back
before accessing I/O memory.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit cf6bf9710c ("scsi: mpt3sas: Bug fix for big endian systems") was
merged to address sparse warnings. However, the patch introduced a
regression on big endian since the code accidentally mixed I/O memory
accessors, which do endian swaps, and regular CPU loads and stores.
Do a partial revert of the offending commit.
[mkp: replaced commit message]
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Just introduce scsi_host_busy() and replace the direct read of
scsi_host->host_busy with this new API.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoids that warnings about the kernel headers appear when building with
W=1. Remove useless "@Returns - Nothing" clauses. Change "@Return - " into
"Return: ".
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Split each of these functions in three functions - one function per reset
phase. This patch does not change any functionality but makes the code
easier to read.
Note: it is much easier to review the git diff -w output after having
applied this patch than by reviewing the patch itself.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since ioc->shost_recovery is set after ioc->reset_in_progress_mutex is
obtained, if concurrent resets are issued there is a short time during
which ioc->reset_in_progress_mutex is locked and ioc->shost_recovery ==
0. Avoid that this can cause trouble by unconditionally locking
ioc->shost_recovery.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make _base_build_nvme_prp() easier to read by introducing a structure
to access NVMe command fields.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify the indentation such that smatch no longer complains about
inconsistent indenting.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Presently driver is using combined reply queue feature when MSI-x vectors >
8 for both SAS3 and SAS3.5 controllers. But as per MPI-spec,
1. For SAS3 controllers, driver should use combined reply queue when HBA
supports more than 8 MSI-x vectors.
2. For SAS3.5 controllers, driver should use combined reply queue when HBA
supports more than 16 MSI-x vectors.
Modified driver code to use combined reply queue for SAS3 controllers when
HBA supports > 8 MSI-x vectors and for SAS3.5 controllers when HBA supports
> 16 MSI-x vectors.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When an ioctl is sent to FW, and if there is a controller reset issued
before ioctl gets completed, then in controller reset path all the pending
ioctl commands are terminated from "mpt3sas_ctl_reset_handler" function.
This will wake up the waiting ioctl commands in ioctl path and print
timeouts which are actually not timeouts.
Introduced "mpt3sas_base_check_cmd_timeout" function to check and print
whether command got timed out (or) terminated due to Host reset.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWyHBVCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishTkjAPoDF71y
5+w0pim7HQvyo02GxKRWyYzkibZsTfNQ49Yo6wD9EhKp1OD4TIrO1ey3fHpCcYry
CHfUIClnev6hiqDBDrI=
=xJ+K
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor (and safe changes) that didn't make the initial
pull request plus some bug fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Mask off Scope bits in retry delay
scsi: qla2xxx: Fix crash on qla2x00_mailbox_command
scsi: aic7xxx: aic79xx: fix potential null pointer dereference on ahd
scsi: mpt3sas: Add an I/O barrier
scsi: qla2xxx: Fix setting lower transfer speed if GPSC fails
scsi: hpsa: disable device during shutdown
scsi: sd_zbc: Fix sd_zbc_check_zone_size() error path
scsi: aacraid: remove bogus GFP_DMA32 specifies
A barrier should be added to ensure proper ordering of memory mapped
writes.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Manufacturing Page 11 contains parameters to control internal
firmware behavior. Based on AddlFlags2 field FW/Driver behaviour can
be changed, (flag tm_custom_handling is used for this)
a) For PCIe device, protocol level reset should be used if flag
tm_custom_handling is 0. Since Abort Task Set, LUN reset and Target
reset will result in a protocol level reset. Drivers should issue
only one type of this reset, if that fails then it should escalate to
a controller reset (diag reset/OCR).
b) If the driver has control over the TM reset timeout value, then
driver should use the value exposed in PCIe Device Page 2 for pcie
device (field ControllerResetTO).
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added function _base_display_fwpkg_version, which sends FWUpload request
to pull FW package version from FW Image Header. Now driver prints FW
package version in addition to FW version if the PackageVersion is
valid.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In function _scsih_add_device, for each device connected to an
enclosure, driver reads the enclosure page(To get details like enclosure
handle, enclosure logical ID, enclosure level etc.)
With this patch, instead of reading enclosure page everytime, driver
maintains a list for enclosure device(During enclosure add event,
enclosure device is added to the list and removed from the list on
delete events) and uses the enclosure page from the list.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS Device Discovery Error Event is sent to the host when discovery
for a particular device is failed during discovery, even after maximum
retries by the IOC.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enhanced DMA allocation for Sense Buffer, if the allocation does not fit
within same 4GB.Introduced is_MSB_are_same function to check if allocted
buffer within 4GB range or not.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For every IO, memory of PAGE size is allocated for handling NVMe native
PRPS. And in addition to that for every IO (chains need per IO * chain
buffer size, e.g. 38 * 128byte) amount of memory is allocated for chain
buffers.
However, at any point of time; the IO request can be for NVMe target
device (where PRP's page is used for framing PRP's) or can be for SCSI
target device (where chain buffers are used for framing chain
SGE's). This patch modifies the driver to reuse same pre-allocated PRP
page buffers as a chain buffer for IO's targeted for SCSI target
devices. No need to allocate separate buffers for chain SGE's buffers.
Suppose if the number of chain buffers need for IO doesn't fit in the
PRP Page size then driver maintain's separate buffers for those extra
chain buffers that exceeds the PRP page size. For example consider PRP
page size as 4K and chain buffer size as 128 bytes, then number of chain
buffers that can fit in PRP page is 4096/128 => 32. if the number of
chain buffer need per IO exceeds 32; for example consider number of
chains need per IO is 36 then for remaining 4 chain buffer's driver
allocates them individual.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduces Chain lookup table/tracker and implements accessing chain
buffer using smid. Removed link list based access of chain buffer which
requires lock and allocated as many chains needed.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of allocating RDPQ array (This stores the address's of each RDPQ
pools) at run time, now it will be allocated once during driver load
time and same will be reused during host reset operation also (instead
of allocating & freeing this buffer on the fly during every host reset
operation) and then freed during driver unload.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes sparse warnings and bugs on big endian systems.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in module parameter description text
[mkp: applied by hand]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Somewhat nasty merge due to conflicts between "33b28357dd00 scsi:
qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc
scsi: qla2xxx: Fix FC-NVMe LUN discovery"
Merge is non-trivial and has been verified by Qlogic (Cavium)
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
The newly added code mixes up phys_addr_t/resource_size_t with dma_addr_t
and void pointers, as seen from these compiler warning:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function '_base_get_chain_phys':
drivers/scsi/mpt3sas/mpt3sas_base.c:235:21: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
base_chain_phys = (void *)ioc->chip_phys + MPI_FRAME_START_OFFSET +
^
drivers/scsi/mpt3sas/mpt3sas_base.c: In function '_clone_sg_entries':
drivers/scsi/mpt3sas/mpt3sas_base.c:427:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
sgel->Address = (dma_addr_t)dst_addr_phys;
^
drivers/scsi/mpt3sas/mpt3sas_base.c:438:7: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
(dma_addr_t)buff_ptr_phys;
^
drivers/scsi/mpt3sas/mpt3sas_base.c:444:10: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
(dma_addr_t)buff_ptr_phys;
Both dma_addr_t and phys_addr_t may be wider than a pointer, so we must
avoid the conversion to pointer types. This also helps readability.
A second problem is treating MMIO addresses from a 'struct resource'
as addresses that can be used for DMA on that device. In almost all
cases, those are the same, but on some of the more obscure architectures,
PCI memory address 0 is mapped into the CPU address space at a nonzero
offset. I don't have a good fix for that, so I'm adding a comment here,
plus a WARN_ON() that triggers whenever the phys_addr_t number is
outside of the low 32-bit address space and causes a straight overflow
when assigned to the 32-bit sgel->Address.
Fixes: 182ac784b4 ("scsi: mpt3sas: Introduce Base function for cloning.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sending I/O through 32 bit descriptors to Ventura series of controller
results in IO timeout on certain conditions. This error only occurs on
systems with high I/O activity.
Changes in this patch will prevent driver from using 32 bit descriptor
and use 64 bit Descriptors
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the posted request has an error of any type, the IOC writes
a Reply message into a host-based system reply message frame.
This functions clone it in the BAR0 mapped region.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Added function _base_clone_mpi_to_sys_mem to clone
MPI request into system BAR0 mapped region.
2) Separate out MPI Endpoint IO submissions to function
_base_put_smid_mpi_ep_scsi_io.
3) MPI EP requests are submitted in two 32 bit MMIO writes.
from _base_mpi_ep_writeq.
For 32 bit Arch,_base_writeq function is identical
to _base_mpi_ep_writeq, Removed duplicate code as suggested.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All scsi IO's and config request's data buffer and sgl are cloned to
system memory in _clone_sg_entries before submitting it to firmware.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For MPI Endpoint/Mcpu, driver should double buffer data buffer/SGLs.
This is normally copied from host to internal memory of IOC by DMA
engine of PCI device. Since the interface to DMA from host to mCPU is
not present for Mcpu/MPI Endpoint device, driver does double copy of
those buffers directly to the mCPU memory region via BAR0 region.
Introduced API to calculate and return BAR0 mapped host buffer's
physical and virtual address for the provided smid.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This configures shost max sector to 128, single reply descriptor post
queue, sgl table size to 16 and 32 bit DMA for MPI Endpoint and it
supports 64K as max IO.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch finishes all outstanding SCSI IO commands (but not other commands,
e.g., task management) in the shutdown and unload paths.
It first waits for the commands to complete (this is done after setting
'ioc->remove_host = 1 ', which prevents new commands to be queued) then it
flushes commands that might still be running.
This avoids triggering error handling (e.g., abort command) for all commands
possibly completed by the adapter after interrupts disabled.
[mauricfo: introduced something in commit message.]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
cpu_msix_table is allocated to store online cpus, but pci_irq_get_affinity
may return cpu_possible_mask which is then used to access cpu_msix_table.
That causes bad user experience. Fix limits access to only online cpus,
I've also added an additional test to protect from an unlikely change in
cpu_online_mask.
[mkp: checkpatch]
Fixes: 1d55abc0e9 ("scsi: mpt3sas: switch to pci_alloc_irq_vectors")
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The function _get_st_from_smid is local to the source and does not need
to be in global scope, so make it static.
Cleans up sparse warning:
symbol '_get_st_from_smid' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance improvement using block layer tag.
Curent driver gets scsiio tracker and free smid from link list and array
based tracking managed by driver. Accessing list in main io path is
performance pentaly because of protection using spinlock
"scsi_lookup_lock".
In this patch:
1. Driver removes all link list access from main io path and
use scmd->request->tag to get free smid.
2. Instead of holding 'struct scsiio_tracker' in its own pool
driver can embed it into the scsi command.
Driver provides cmd_size in scsi_host_template, so that struct
scsiio_tracker is preallocated by scsi mid layer for each scsi command.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use 'host_busy' instead of counting outstanding commands by hand.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ioctl passthrough commands require a SCSIIO smid, but cannot easily
integrate with the block layer. But the driver already has reserved some
SCSIIO smids and we're only ever allowing one ioctl command at a time we
can use the first reserved smid for ioctl commands.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Abstract accesses to the scsi_lookup array by introducing
mpt3sas_get_st_from_smid().
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use 'list_splice_init()' instead of hand-crafted function. No
functional change.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
The newly added base_make_prp_nvme function triggers a build warning on
some 32-bit configurations:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function 'base_make_prp_nvme':
drivers/scsi/mpt3sas/mpt3sas_base.c:1664:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
msg_phys = (dma_addr_t)mpt3sas_base_get_pcie_sgl_dma(ioc, smid);
After taking a closer look, I found that the problem is that the new
code mixes up pointers and dma_addr_t values unnecessarily.
This changes it to use the correct types consistently, which lets us get
rid of a lot of type casts in the process. I'm also renaming some
variables to avoid confusion between physical and dma address spaces
that are often distinct.
Fixes: 016d5c35e2 ("scsi: mpt3sas: SGL to PRP Translation for I/Os to NVMe devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Used variable __le64/__le32 whichever required in building NVME
PRP, and passed to LE Controller.
2) Remove unused functions, And Declared functions as static which are
used only in mpt3sas_scsih.c.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* The controller firmware sends separate events for NVMe devices and
PCIe switches similar to existing SAS events.
* NVMe device detection, addition and removal are reported by the
firmware through PCIe Topology Change list events.
* The PCIe device state change events are sent when the firmware
detects any abnormal conditions with a NVMe device or switch.
* The enumeration event are sent when the firmware starts PCIe device
enumeration and stops.
* This patch has the code change to handle the events and add/remove
NVMe devices in driver's inventory.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Mpt3sas driver uses the NVMe Encapsulated Request message to send an
NVMe command to an NVMe device attached to the IOC.
* Normal I/O commands like reads and writes are passed to the
controller as SCSI commands and the controller has the ability to
translate the commands to NVMe equivalent.
* This encapsulated NVMe command is used by applications to send
direct NVMe commands to NVMe drives.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
* Added support for translating the SGLs associated with incoming
commands either to IEE SGL or NVMe PRPs for NVMe devices.
* The hardware translation of IEEE SGL to NVMe PRPs has limitations
and if a command cannot be translated by hardware then it will go to
firmware and the firmware needs to translate it. This will have a
performance impact. To avoid that, the driver proactively checks
whether the translation will be done in hardware or not. If not, then
driver translates.
[mkp: clarified commit message]
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
To reduce the memory footprint of the driver in the kdump kernel, we
apply the following settings when reset_devices is set:
1. Use single MSI-x vector.
2. Disable RDPQ mode.
3. Set sg_table_size to 32 by default.
4) Set SCSI IO Queue depth to 200.
[mkp: fixed commit message]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Earlier Active Cable Exception event with reason code "Cable Degraded
(0x02))" was added only for Active Cable. Now this event is extended to
Passive cable too. Re-arranged display message accordingly.
Also added Cable Exception Event event for SAS3008 & SAS3108 HBAs
(i.e. MPI 2.5 spec supporting HBAs). Previously, this event was enabled
only for MPI 2.6 spec supporting HBA devices.
[mkp: typos]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
An optional discovery status should be printed with a pr_cont and needs
a leading space to make it more readable. The final new line should also
be a pr_cont and the indentation is out by one, so fix that too.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In the lines above this test, 8 'kzalloc' are performed, but only 7
results are tested.
Add the missing one (i.e. '!ioc->port_enable_cmds.reply').
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to relaxed ordering requirements on multiple architectures, drivers
are required to use wmb/rmb/mb combinations when they need to guarantee
observability between the memory and the HW.
The mpt3sas driver is already using wmb() for this purpose. However, it
issues a writel following wmb(). writel() function on arm/arm64
arhictectures have an embedded wmb() call inside.
This results in unnecessary performance loss and code duplication.
writel already guarantees ordering for both cpu and bus. we don't need
additional wmb()
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cleanup the MSI-X handling allowing us to use the PCI-layer provided
vector allocation.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due existence of loop in the IO path our HBA will receive heavy IOs and
also as driver is not updating the Reply Post Host Index frequently, So
there will be a high chance that our Firmware unable to find any free
entry in the Reply Post Descriptor Queue (i.e. Queue overflow occurs)
and can observe 0x2100 firmware fault. So to fix this, we have defined
a thresh hold value. After continuously processing this thresh hold
number of reply descriptors driver will update the Reply Descriptor Host
Index so that this thresh hold number of reply descriptors entries will
be freed and these entries will be available for firmware and we won't
observe this Firmware fault. We have defined this threshold value as
1/3rd of the hba queue depth.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Small glitch/degraded performance in Crusader is improved with SAS
drives by removing unnecessary spinlocks while clearing scsi command in
drivers internal lookup table.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Support Atomic Request Descriptors for Ventura/SAS35 devices.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SAS35 devices MSIX vectors are inceased to 128 from 96. To support this
Reply post host index register count is increased to 16. Also variable
msix96_vector is replaced with combined_reply_queue and variable
combined_reply_index_count is added to set different values for SAS3 and
SAS35 devices.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When device missing event arrives, device_remove_in_progress bit will be
set and hence driver has to stop sending IOCTL commands.Now the check has
been added in IOCTL path to test device_remove_in_progress bit is set, if
so then IOCTL will be failed printing failure message.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No. of MSIX vectors supported = min (Total no. of CPU cores,
MSIX vectors supported by card)
when RDPQ is disabled "max_msix_vectors" module parameter which was
declared as global was set to '8' and hence if there are more than one card
in system among which if RDPQ disabled card is enumerated first then only 8
MSIX vectors was getting enabled for all the cards(including RDPQ enabled
card,which can support more than 8 MSIX vectors).
Used local variable instead of global variable ,if RDPQ is disabled this
local variable is set to '8' else it is set to "max_msix_vectors" (by
default this is set to -1, whose value can be set by user during driver
load time).So now regardless of whether RDPQ disabled card is enumerated
first or RDPQ enabled card is enumerated first , MSIX vectors enabled
depends on the cards capability.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This update includes the usual round of major driver updates (hpsa, be2iscsi,
hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa called smartpqi
for which a driver is added, there's some cleanup work of the ibm vscsi target
and updates to libfc, plus a whole host of minor fixes and updates and finally
the removal of several ISA drivers which seem not to have been used for years.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cyTO
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (hpsa,
be2iscsi, hisi_sas, zfcp, cxlflash). There's a new incarnation of hpsa
called smartpqi for which a driver is added, there's some cleanup work
of the ibm vscsi target and updates to libfc, plus a whole host of
minor fixes and updates and finally the removal of several ISA drivers
which seem not to have been used for years"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (173 commits)
scsi: mvsas: Mark symbols static where possible
scsi: pm8001: Mark symbols static where possible
scsi: arcmsr: Simplify user_len checking
scsi: fcoe: fix off by one in eth2fc_speed()
scsi: dtc: remove from tree
scsi: t128: remove from tree
scsi: pas16: remove from tree
scsi: u14-34f: remove from tree
scsi: ultrastor: remove from tree
scsi: in2000: remove from tree
scsi: wd7000: remove from tree
scsi: scsi_dh_alua: Fix memory leak in alua_rtpg()
scsi: lpfc: Mark symbols static where possible
scsi: hpsa: correct call to hpsa_do_reset
scsi: ufs: Get a TM service response from the correct offset
scsi: ibmvfc: Fix I/O hang when port is not mapped
scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up
scsi: ipr: Remove redundant messages at adapter init time
scsi: ipr: Don't log unnecessary 9084 error details
scsi: smartpqi: raid bypass lba calculation fix
...
Trivial non-functional changes for a couple annoying things:
1) Functions local to files are not declared static, which is
frustrating when reading the code because it's non-obvious at first
glance what's actually called from other files.
2) Set-but-unused variables abound, presumably to mask -Wunused-result
errors in the past. None of these are flagged today though (with one
exception noted below), so remove them.
Fixing (2) exposed the fact that we improperly ignore the return value
of scsi_device_reprobe() in _scsih_reprobe_lun(). Fixing the calling
code to deal with the potential error is non-trivial, so for now just
WARN().
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the exception of a single call to wait_for_doorbell_int(), all this
conditional sleeping code is dead. So delete it.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"
This event is only for Intruder/Cutlass HBAs.
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _base_make_ioc_operational(), we walk ioc->reply_queue_list and pull
a pointer out of successive elements of ioc->reply_post[] for each entry
in that list if RDPQ is enabled.
Since the code pulls the pointer for the next iteration at the bottom of
the loop, it triggers the a KASAN dump on the final iteration:
BUG: KASAN: slab-out-of-bounds in _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas] at addr ffff880754816ab0
Read of size 8 by task modprobe/305
<snip>
Call Trace:
[<ffffffff81dfc591>] dump_stack+0x4d/0x6c
[<ffffffff814c9689>] print_trailer+0xf9/0x150
[<ffffffff814ceda4>] object_err+0x34/0x40
[<ffffffff814d1231>] kasan_report_error+0x221/0x530
[<ffffffff814d1673>] __asan_report_load8_noabort+0x43/0x50
[<ffffffffa0043637>] _base_make_ioc_operational+0x47b7/0x47e0 [mpt3sas]
[<ffffffffa0049a51>] mpt3sas_base_attach+0x1991/0x2120 [mpt3sas]
[<ffffffffa0053c93>] _scsih_probe+0xeb3/0x16b0 [mpt3sas]
[<ffffffff81ebd047>] local_pci_probe+0xc7/0x170
[<ffffffff81ebf2cf>] pci_device_probe+0x20f/0x290
[<ffffffff820d50cd>] really_probe+0x17d/0x600
[<ffffffff820d56a3>] __driver_attach+0x153/0x190
[<ffffffff820cffac>] bus_for_each_dev+0x11c/0x1a0
[<ffffffff820d421d>] driver_attach+0x3d/0x50
[<ffffffff820d378a>] bus_add_driver+0x44a/0x5f0
[<ffffffff820d666c>] driver_register+0x18c/0x3b0
[<ffffffff81ebcb76>] __pci_register_driver+0x156/0x200
[<ffffffffa00c8135>] _mpt3sas_init+0x135/0x1000 [mpt3sas]
[<ffffffff81000423>] do_one_initcall+0x113/0x2b0
[<ffffffff813caa5a>] do_init_module+0x1d0/0x4d8
[<ffffffff81273909>] load_module+0x6729/0x8dc0
[<ffffffff81276123>] SYSC_init_module+0x183/0x1a0
[<ffffffff8127625e>] SyS_init_module+0xe/0x10
[<ffffffff828fe7d7>] entry_SYSCALL_64_fastpath+0x12/0x6a
Fix this by pulling the value at the beginning of the loop.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jens Axboe <axboe@fb.com>
Acked-by: Chaitra Basappa <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling synchronize_irq() right before free_irq() is quite useless. On
one hand the IRQ can easily fire again before free_irq() is entered, on
the other hand free_irq() itself calls synchronize_irq() internally (in
a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Deallocate resources before reallocating of the same in retry_allocation
path of _base_allocate_memory_pools()
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Removed cpumask_clear as it is not required for zalloc_cpumask_var and
free free_cpumask_var before freeing reply_q.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Track msix of each IO and use the same msix for issuing abort to timed
out IO. With this driver will process IO's reply first followed by TM.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Added support for configurable Chain Frame Size. Calculate the
Chain Message Frame size from the IOCMaxChainSegementSize (iocfacts).
Applicable only for mpt3sas/SAS3.0 HBA's.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Module parameter to enable/disable configuring affinity hint for msix
vector. SMP affinity feature can be enabled/disabled by setting module
parameter "smp_affinity_enable" to 1/0. By default this feature is
enabled. (smp_affinity_enable = 1 enabled).
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver assumes HighPriority credit as part of Global credit. But,
Firmware treats HighPriority credit value and global cedits as two
different values. Changed host queue algorithm to treat global credits
and highPriority credits as two different values.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated hardware description headers with MPI v2.6 and
mpt3sas_pci_table[] with vendor_ids, device_ids of Cutlass and Intruder
HBA which have support for 4 ports.
Signed-off-by: Suganath prabu Subramani <suganath-prabu.subramani@avagotech.com>
Signed-off-by: Chaitra P B <chaitra.basappa@avagotech.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It might happen that we try to free an already freed pointer.
Reported-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Chaitra P B <chaitra.basappa@avagotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
