The new i2c implementation for PowerMac has a regression that causes the
hardware to go out of state when probing non-existent devices. While
fixing that, I also found & fixed a couple of other corner cases. This
fixes booting with a pbbuttons version that scans the i2c bus for an LMU
controller among others. Tested on a dual G5 with thermal control (which
has heavy i2c activity) with no problem so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Turn on the DART already at 1GB. This is needed because of crippled
devices in some systems, i.e. Airport Extreme cards, only supporting
30-bit DMA addresses.
Otherwise, users with between 1 and 2GB of memory will need to manually
enable it with iommu=force, and that's no good.
Some simple performance tests show that there's a slight impact of
enabling DART, but it's in the 1-3% range (kernel build with disk I/O
as well as over NFS).
iommu=off can still be used for those who don't want to deal with the
overhead (and don't need it for any devices).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some devices don't support full 32-bit DMA address space, which we currently
assume. Add the required mask-passing to the IOMMU allocators.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes. There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.
This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines. Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Use correct sequence for putting CPU into nap mode
[PATCH] spufs: fix context-switch decrementer code
[PATCH] powerpc32: Set cpu explicitly in kernel compiles
[PATCH] powerpc/pseries: bugfix: balance calls to pci_device_put
[PATCH] powerpc: Fix machine detection in prom_init.c
[PATCH] ppc32: Fix string comparing in platform_notify_map
[PATCH] powerpc: Avoid __initcall warnings
[PATCH] powerpc: Ensure runlatch is off in the idle loop
powerpc: Fix CHRP booting - needs a define_machine call
powerpc: iSeries has only 256 IRQs
We weren't using the recommended sequence for putting the CPU into
nap mode. When I changed the idle loop, for some reason 7447A cpus
started hanging when we put them into nap mode. Changing to the
recommended sequence fixes that.
The complexity here is that the recommended sequence is a loop that
keeps putting the cpu back into nap mode. Clearly we need some way
to break out of the loop when an interrupt (external interrupt,
decrementer, performance monitor) occurs. Here we use a bit in
the thread_info struct to indicate that we need this, and the exception
entry code notices this and arranges for the exception to return
to the value in the link register, thus breaking out of the loop.
We use a new `local_flags' field in the thread_info which we can
alter without needing to use an atomic update sequence.
The PPC970 has the same recommended sequence, so we do the same thing
there too.
This also fixes a bug in the kernel stack overflow handling code on
32-bit, since it was causing a value that we needed in a register to
get trashed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We found that when the 'decrementer' is saved, the PPE saves the current
time 'csa->suspend_time'. When restoring the 'decrementer', (Step 34)
decrementer seems to be adjusted with the number of cycles th= at a spu
thread has not been running.
In that code it is missing a substract ('-') because 'delta_time' is
assigned a not substracted(see bellow).
Acked-by: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compile the 32bit kernel with -mcpu=powerpc. This reduces the imagesize
when a compiler is used that defaults to -mtune=power4. It inserts lots
of nops to please the 64bit cpu instruction scheduling. But all these nops
are not needed for 32bit kernels.
Example with SLES10 gcc 4.1.0 and arch/powerpc/configs/pmac32_defconfig:
vmlinux vmlinux.strip vmlinux.gz
-O2 4980515 4187528 1846829
-Os 4618801 3827084 1673333
-O2 -mcpu=powerpc 4738851 3945868 1816253
-Os -mcpu=powerpc 4532785 3741068 1664688
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Repeated calls to eeh_remove_device() can result in multiple
(and thus unbalanced) calls to pci_dev_put(). Make sure the
pci_device_put() is called only once (since there was only
one call to the matching pci_device_get()).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In e8222502ee the detection of machine types
in prom_init broke for some machines. We should be checking /device_type
instead of /model. This should make Power3 and Power4 boot again. Haven't
been able to test this. We also need to relocate before comparing.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix __initcall return in proc_rtas_init and rtas_init.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since external and decrementer interrupts set the runlatch on, we need
to ensure its set off again in the idle loop. At the moment we dont turn
it off in the inner loop.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Basically an in-kernel implementation of tee, which uses splice and the
pipe buffers as an intelligent way to pass data around by reference.
Where the user space tee consumes the input and produces a stdout and
file output, this syscall merely duplicates the data inside a pipe to
another pipe. No data is copied, the output just grabs a reference to the
input pipe data.
Signed-off-by: Jens Axboe <axboe@suse.de>
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch removing _machine and converting platforms over to use
define_machine wasn't complete as far as CHRP was concerned. This
adds the define_machine call for CHRP and gets it booting again.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The iSeries Hypervisor only allows us to specify IRQ numbers up to 255 (it
has a u8 field to pass it in). This patch allows platforms to specify a
maximum to the virtual IRQ numbers we will use and has iSeries set that
to 255. If not set, the maximum is NR_IRQS - 1 (as before).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Since the powerpc 64k pages patch went in, systems that have SLBs
(like Power4 iSeries) needed to have slb_initialize called to set up
some variables for the SLB miss handler. This was not being called
on the boot processor on iSeries, so on single cpu iSeries machines,
we would get apparent memory curruption as soon as we entered user mode.
This patch fixes that by calling slb_initialize on the boot cpu if the
processor has an SLB.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Missing include for __NR_syscalls, and missing sys_splice() that
causes build-time failure due to compile-time bounds check on
spu_syscall_table.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes unnecessary exports, marks functions as static when
possible, and simplifies some list-related code.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes several problems with the lparcfg code. In case
someone gets a sense of deja-vu, part of this was submitted last Sep, I
thought the changes went in, but either got backed out, or just got
lost.
First, change the local_buffer declaration to be unsigned char *. We
had a bad-math problem in a 2.4 tree which was built with a
"-fsigned-char" parm. I dont believe we ever build with that parm
now-a-days, but to be safe, I'd prefer the declaration be explicit.
Second, fix a bad math calculation for splpar_strlen.
Third, on the rtas_call for get-system-parameter, pass in
RTAS_DATA_BUF_SIZE for the rtas_data_buf size, instead of letting random
data determine the size. Until recently, we've had a sufficiently
large 'random data' value get passed in, so the function just happens to
have worked OK. Now it's getting passed a '0', which causes the
rtas_call to return success, but no data shows up in the buffer.
(oops!). This was found by the LTC test org.
This is in a branch of code that only gets run on SPLPAR systems.
Tested on power5 Lpar.
Signed-off-by: Will Schmidt <willschm@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent patch to print device names in EEH reset messages
was lacking ... this patch works better.
Signed-off-by: Linas Vepstas <linas@linas.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This extends the HCALL interface for InfiniBand usage. I've
made the patch against the linux-2.6 git tree and Segher's patch:
[PATCH] Change H_StudlyCaps to H_SHOUTING_CAPS
We moved this into the common powerpc code based on comments we
got after posting the first eHCA InfiniBand device driver patch.
Signed-off-by: Heiko j Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also cleans up some nearby whitespace problems.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current code prints an ambiguous message if the recovery
of a failed PCI device fails. Give this special case its own
unique message.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This forces the processing of EEH PCI events to be serialized,
using a very simple mutex lock. This serialization is required to
avoid races involving additional PCI device failures that may occur
during the recovery phase of a previous failure.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The only user of get_wchan is the proc fs - and proc can't be built modular.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark unwind info for signal trampolines using the new S augmentation flag
introduced in: http://gcc.gnu.org/PR26208.
GCC 4.2 (or patched earlier GCC) will be able to special case unwinding
through frames right above signal trampolines. As the augmentations start
with z flag and S is at the very end of the augmentation string, older GCCs
will just skip the S flag as unknown (that's why an augmentation flag was
chosen over say a new CFA opcode).
Signed-off-by: Jakub Jelinek <jakub@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed platform_init usage on 83xx and 85xx and use define_machine and
probe(). For now we always return true in the problem since you can only
build for one specific board at a time. This is an artificial constraint.
When we get ride of it we will need to update the Kconfig's for these
sub-arch's and make the board's probe() functions actually do something.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove oprofile spinlock backtrace code now we have proper calltrace
support. Also make MMCRA sihv and sipr bits a variable since they may
change in future cpus. Finally, MMCRA should be a 64bit quantity.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add calltrace support for other powerpc cpus. Tested on 7450.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add oprofile calltrace support to powerpc. Disable spinlock backtracing
now we can use calltrace info.
(Updated to work on both 32bit and 64bit by me).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix 44x and BookE page fault handler to correctly lock PTE before
trying to pte_update() it, otherwise this PTE might be swapped out
after pte_present() check but before pte_uptdate() call, resulting in
corrupted PTE. This can happen with enabled preemption and low memory
condition.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We used to assume that a DMA mapping request with a NULL dev was for
ISA DMA. This assumption was broken at some point. Now we explicitly
pass the detected ISA PCI device in the floppy setup.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Non zero initcalls (except for -ENODEV) have started warning at boot.
Fix smt_setup and init_ras_IRQ.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bug in the RTAS services incorrectly interprets some bits in the CR
when called from the OS. Specifically, bits in CR4. The result could
be a firmware crash that also takes down the partition. A firmware
fix is in the works. We have seen this situation when performing DLPAR
operations. As a temporary workaround, clear the CR in enter_rtas().
Note that enter_rtas() will not set any bits in CR4 before calling RTAS.
Also note that the 32 bit version of enter_rtas() should have the same
work around even though the chances of hitting the bug are much smaller
due to the lack of DLPAR on 32 bit kernels. However, my assembly skills
are a bit rusty and the 32 bit code doesn't seem to follow the conventions
for where things should be saved. In addition, I don't have a system
to test 32 bit kernels. Help creating and at least touch testing the
same workaround for 32 bit would be appreciated.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spufs_init and spufs_exit should be marked correctly so
they can be removed when not needed.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These are some updates from both Ryan and Arnd for the hvc_console
driver:
The main point is to enable the inclusion of a console driver
for rtas, which is currrently needed for the cell platform.
Also shuffle around some data-type declarations and moves some
functions out of include/asm-ppc64/hvconsole.h and into a new
drivers/char/hvc_console.h file.
Signed-off-by: "Ryan S. Arnold" <rsa@us.ibm.com>
Signed-off-by: Arnd Bergmann <abergman@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
*) When setting a sighandler using sigaction() call, if the flag
SA_ONSTACK is set and no alternate stack is provided via sigaltstack(),
the kernel still try to install the alternate stack. This behavior is
the opposite of the one which is documented in Single Unix
Specifications V3.
*) Also when setting an alternate stack using sigaltstack() with the
flag SS_DISABLE, the kernel try to install the alternate stack on
signal delivery.
These two use cases makes the process crash at signal delivery.
This fixes it.
Signed-off-by: Laurent Meyer <meyerlau@fr.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to export ppc64_firmware_features for modules. Before we do that
I think we should probably rename it to powerpc_firmware_features.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we build for the MPC8540 ADS produce a uImage by default.
Updated the defconfig to reflect this as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Towards the goal of having arch/powerpc not build anything over in arch/ppc
move math-emu over. Also, killed some references to arch/ppc/ in the
arch/powerpc Makefile which should belong in drivers/ when the particular
sub-arch's move over to arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Export validate_sp so we can use it in the oprofile calltrace code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a mistake I made when editing these functions - when I
took out the interrupt disabling code (because interrupts are now
disabled by the caller) I left the register that is used for the MSR
value to be used during doze/nap uninitialized. This fixes it.
Also updated some of the comments in idle_power4.S and removed some
code that was copied over from idle_6xx.S but is no longer relevant
(we don't ever clear the CPU_FTR_CAN_NAP bit at runtime for POWER4).
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kernel's implementation of notifier chains is unsafe. There is no
protection against entries being added to or removed from a chain while the
chain is in use. The issues were discussed in this thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=113018709002036&w=2
We noticed that notifier chains in the kernel fall into two basic usage
classes:
"Blocking" chains are always called from a process context
and the callout routines are allowed to sleep;
"Atomic" chains can be called from an atomic context and
the callout routines are not allowed to sleep.
We decided to codify this distinction and make it part of the API. Therefore
this set of patches introduces three new, parallel APIs: one for blocking
notifiers, one for atomic notifiers, and one for "raw" notifiers (which is
really just the old API under a new name). New kinds of data structures are
used for the heads of the chains, and new routines are defined for
registration, unregistration, and calling a chain. The three APIs are
explained in include/linux/notifier.h and their implementation is in
kernel/sys.c.
With atomic and blocking chains, the implementation guarantees that the chain
links will not be corrupted and that chain callers will not get messed up by
entries being added or removed. For raw chains the implementation provides no
guarantees at all; users of this API must provide their own protections. (The
idea was that situations may come up where the assumptions of the atomic and
blocking APIs are not appropriate, so it should be possible for users to
handle these things in their own way.)
There are some limitations, which should not be too hard to live with. For
atomic/blocking chains, registration and unregistration must always be done in
a process context since the chain is protected by a mutex/rwsem. Also, a
callout routine for a non-raw chain must not try to register or unregister
entries on its own chain. (This did happen in a couple of places and the code
had to be changed to avoid it.)
Since atomic chains may be called from within an NMI handler, they cannot use
spinlocks for synchronization. Instead we use RCU. The overhead falls almost
entirely in the unregister routine, which is okay since unregistration is much
less frequent that calling a chain.
Here is the list of chains that we adjusted and their classifications. None
of them use the raw API, so for the moment it is only a placeholder.
ATOMIC CHAINS
-------------
arch/i386/kernel/traps.c: i386die_chain
arch/ia64/kernel/traps.c: ia64die_chain
arch/powerpc/kernel/traps.c: powerpc_die_chain
arch/sparc64/kernel/traps.c: sparc64die_chain
arch/x86_64/kernel/traps.c: die_chain
drivers/char/ipmi/ipmi_si_intf.c: xaction_notifier_list
kernel/panic.c: panic_notifier_list
kernel/profile.c: task_free_notifier
net/bluetooth/hci_core.c: hci_notifier
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_chain
net/ipv4/netfilter/ip_conntrack_core.c: ip_conntrack_expect_chain
net/ipv6/addrconf.c: inet6addr_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_chain
net/netfilter/nf_conntrack_core.c: nf_conntrack_expect_chain
net/netlink/af_netlink.c: netlink_chain
BLOCKING CHAINS
---------------
arch/powerpc/platforms/pseries/reconfig.c: pSeries_reconfig_chain
arch/s390/kernel/process.c: idle_chain
arch/x86_64/kernel/process.c idle_notifier
drivers/base/memory.c: memory_chain
drivers/cpufreq/cpufreq.c cpufreq_policy_notifier_list
drivers/cpufreq/cpufreq.c cpufreq_transition_notifier_list
drivers/macintosh/adb.c: adb_client_list
drivers/macintosh/via-pmu.c sleep_notifier_list
drivers/macintosh/via-pmu68k.c sleep_notifier_list
drivers/macintosh/windfarm_core.c wf_client_list
drivers/usb/core/notify.c usb_notifier_list
drivers/video/fbmem.c fb_notifier_list
kernel/cpu.c cpu_chain
kernel/module.c module_notify_list
kernel/profile.c munmap_notifier
kernel/profile.c task_exit_notifier
kernel/sys.c reboot_notifier_list
net/core/dev.c netdev_chain
net/decnet/dn_dev.c: dnaddr_chain
net/ipv4/devinet.c: inetaddr_chain
It's possible that some of these classifications are wrong. If they are,
please let us know or submit a patch to fix them. Note that any chain that
gets called very frequently should be atomic, because the rwsem read-locking
used for blocking chains is very likely to incur cache misses on SMP systems.
(However, if the chain's callout routines may sleep then the chain cannot be
atomic.)
The patch set was written by Alan Stern and Chandra Seetharaman, incorporating
material written by Keith Owens and suggestions from Paul McKenney and Andrew
Morton.
[jes@sgi.com: restructure the notifier chain initialization macros]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On CHRP machines we are supposed to call into firmware (RTAS)
periodically, to give it a chance to check for errors and other
events. Under ppc we had some special code in timer_interrupt
to do this, but that didn't get transferred over to arch/powerpc.
Instead, we use an array of timer_list structs, one per CPU,
and use add_timer_on to make sure each one gets called on the
appropriate CPU.
With this we can remove the heartbeat_* elements of the ppc_md
struct.
Signed-off-by: Paul Mackerras <paulus@samba.org>
All of the things needed for 32-bit ARCH=powerpc builds have now
moved to arch/powerpc/kernel, so we don't need to go down into
arch/ppc/kernel any more, and we can remove the CONFIG_PPC_MERGE
conditional from arch/ppc/kernel/Makefile.
There were two files still referenced in the merge section of
arch/ppc/kernel/Makefile: ppc-stub.o, depending on CONFIG_KGDB,
and dma-mapping.o, depending on CONFIG_NOT_COHERENT_CACHE. None
of the platforms currently in ARCH=powerpc have caches that
aren't coherent with DMA, but when we do get one we'll move
dma-mapping.c over. As for CONFIG_KGDB, none of the Kconfig
files in the tree define it, so I'll let it languish for now.
Signed-off-by: Paul Mackerras <paulus@samba.org>
... and rename it to module_32.c since it is the 32-bit version.
The 32-bit and 64-bit ABIs are sufficiently different that having
a merged version isn't really practical.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also renamed temp.c to tau_6xx.c (for thermal assist unit) and updated
the Kconfig option description and help text for CONFIG_TAU.
Signed-off-by: Paul Mackerras <paulus@samba.org>
No functional changes, but call it l2cr_6xx.S since it is specific
to 6xx-family (including G3/750 and G4/74xx) processors.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since pSeries only wants to do something different in the idle loop when
there is no work to do, we can simplify the code by implementing
ppc_md.power_save functions instead of complete idle loops. There are
two versions: one for shared-processor partitions and one for dedicated-
processor partitions.
With this we also do a cede_processor() call on dedicated processor
partitions if the poll_pending() call indicates that the hypervisor
has work it wants to do.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This unifies the 32-bit (ARCH=ppc and ARCH=powerpc) and 64-bit idle
loops. It brings over the concept of having a ppc_md.power_save
function from 32-bit to ARCH=powerpc, which lets us get rid of
native_idle(). With this we will also be able to simplify the idle
handling for pSeries and cell.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We only ever execute the loop once, so let's move it to a function
making it more readable. Cleanup patch, no functional change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were printing node ids in hex in one spot. Lets be consistent and
always print them in decimal.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a hack to flip the boot cpu and its secondary thread
to logical cpuid 0 and 1. This means the logical - physical mapping will
differ depending on which cpu is boot cpu. This is most apparent on
kexec, where we might kexec on any cpu and therefore change the mapping
from boot to boot.
The patch below does a first pass early on to work out the logical cpuid
of the boot thread. We then fix up some paca structures to match.
Ive also removed the boot_cpuid_phys variable for ppc64, to be
consistent we use get_hard_smp_processor_id(boot_cpuid) everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an SPE attempts a DMA put to a local store after already doing
a get, the kernel must update the HW PTE to allow the write access.
This case was not being handled correctly.
From: Mike Kistler <mkistler@us.ibm.com>
Signed-off-by: Mike Kistler <mkistler@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I'm not sure where the information came from, but I assumed
that doing cache-inhibited mappings for mmio regions was
sufficient.
It seems we also need the guarded bit set, like everyone
else, which is the default for ioremap.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As noticed by Milton Miller, setting the initial affinity in
spider-pic can go wrong if the target node field was not orinally
empty.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the dynamic PCI probe function for pSeries to use
ppc_md.pci_probe_mode() when appropriate.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do not call prom exit prom_panic. It clears the screen and the exit
message is lost.
On some (or all?) pmacs it causes another crash when OF tries to print
the date and time in its banner.
Set of_platform earlier to catch more prom_panic() calls.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The return statement is to prevent `warning: 'nid' might be used uninitialized
in this function'.
Cc: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The address of variable val in prom_init_stdout is passed to prom_getprop.
prom_getprop casts the pointer to u32 and passes it to call_prom in the hope
that OpenFirmware stores something there.
But the pointer is truncated in the lower bits and the expected value is
stored somewhere else.
In my testing I had a stackpointer of 0x0023e6b4. val was at offset 120,
wich has address 0x0023e72c. But the value passed to OF was 0x0023e728.
c00000000040b710: 3b 01 00 78 addi r24,r1,120
...
c00000000040b754: 57 08 00 38 rlwinm r8,r24,0,0,28
...
c00000000040b784: 80 01 00 78 lwz r0,120(r1)
...
c00000000040b798: 90 1b 00 0c stw r0,12(r27)
...
The stackpointer came from 32bit code.
The chain was yaboot -> zImage -> vmlinux
PowerMac OpenFirmware does appearently not handle the ELF sections
correctly. If yaboot was compiled in
/usr/src/packages/BUILD/lilo-10.1.1/yaboot, then the stackpointer is
unaligned. But the stackpointer is correct if yaboot is compiled in
/tmp/yaboot.
This bug triggered since 2.6.15, now prom_getprop is an inline
function. gcc clears the lower bits, instead of just clearing the
upper 32 bits.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
the mfc member of a new context was not initialized to zero,
which potentially leads to wild memory accesses.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch is layered on top of CONFIG_SPARSEMEM
and is patterned after direct mapping of LS.
This patch allows mmap() of the following regions:
"mfc", which represents the area from [0x3000 - 0x3fff];
"cntl", which represents the area from [0x4000 - 0x4fff];
"signal1" which begins at offset 0x14000; "signal2" which
begins at offset 0x1c000.
The signal1 & signal2 files may be mmap()'d by regular user
processes. The cntl and mfc file, on the other hand, may
only be accessed if the owning process has CAP_SYS_RAWIO,
because they have the potential to confuse the kernel
with regard to parallel access to the same files with
regular file operations: the kernel always holds a spinlock
when accessing registers in these areas to serialize them,
which can not be guaranteed with user mmaps,
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a new file called 'mfc' to each spufs directory.
The file accepts DMA commands that are a subset of what would
be legal DMA commands for problem state register access. Upon
reading the file, a bitmask is returned with the completed
tag groups set.
The file is meant to be used from an abstraction in libspe
that is added by a different patch.
From the kernel perspective, this means a process can now
offload a memory copy from or into an SPE local store
without having to run code on the SPE itself.
The transfer will only be performed while the SPE is owned
by one thread that is waiting in the spu_run system call
and the data will be transferred into that thread's
address space, independent of which thread started the
transfer.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An SPU does not have a way to implement system calls
itself, but it can create intercepts to the kernel.
This patch uses the method defined by the JSRE interface
for C99 host library calls from an SPU to implement
Linux system calls. It uses the reserved SPU stop code
0x2104 for this, using the structure layout and syscall
numbers for ppc64-linux.
I'm still undecided wether it is better to have a list
of allowed syscalls or a list of forbidden syscalls,
since we can't allow an SPU to call all syscalls that
are defined for ppc64-linux.
This patch implements the easier choice of them, with a
blacklist that only prevents an SPU from calling anything
that interacts with its own execution, e.g fork, execve,
clone, vfork, exit, spu_run and spu_create and everything
that deals with signals.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc currently declares some of its own system calls
in <asm/unistd.h>, but not all of them. That place also
contains remainders of the now almost unused kernel syscall
hack.
- Add a new <asm/syscalls.h> with clean declarations
- Include that file from every source that implements one
of these
- Get rid of old declarations in <asm/unistd.h>
This patch is required as a base for implementing system
calls from an SPU, but also makes sense as a general
cleanup.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently we have found a bug in the CPU that causes
external interrupts to sometimes get disabled indefinitely.
This adds a workaround for the problem.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current interrupt controller setup on Cell is done
in a rather ad-hoc way with device tree properties
that are not standardized at all.
In an attempt to do something that follows the OF standard
(or at least the IBM extensions to it) more closely,
we have now come up with this patch. It still provides
a fallback to the old behaviour when we find older firmware,
that hack can not be removed until the existing customer
installations have upgraded.
Cc: hpenner@de.ibm.com
Cc: stk@de.ibm.com
Cc: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Milton Miller <miltonm@bga.com>
Cc: benh@kernel.crashing.org
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The default configuration in mainline got a little out of
sync with what we use internally.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A small bug crept in the iommu driver when we made it more
generic. This patch is needed for boards that have a dma
window that does not start at bus address zero.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide proper kprobes fault handling, if a user-specified pre/post handlers
tries to access user address space, through copy_from_user(), get_user() etc.
The user-specified fault handler gets called only if the fault occurs while
executing user-specified handlers. In such a case user-specified handler is
allowed to fix it first, later if the user-specifed fault handler does not fix
it, we try to fix it by calling fix_exception().
The user-specified handler will not be called if the fault happens when single
stepping the original instruction, instead we reset the current probe and
allow the system page fault handler to fix it up.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently kprobe handler traps only happen in kernel space, so function
kprobe_exceptions_notify should skip traps which happen in user space.
This patch modifies this, and it is based on 2.6.16-rc4.
Signed-off-by: bibo mao <bibo.mao@intel.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Keshavamurthy, Anil S" <anil.s.keshavamurthy@intel.com>
Cc: <hiramatu@sdl.hitachi.co.jp>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When kretprobe probes the schedule() function, if the probed process exits
then schedule() will never return, so some kretprobe instances will never
be recycled.
In this patch the parent process will recycle retprobe instances of the
probed function and there will be no memory leak of kretprobe instances.
Signed-off-by: bibo mao <bibo.mao@intel.com>
Cc: Masami Hiramatsu <hiramatu@sdl.hitachi.co.jp>
Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create compat_sys_adjtimex and use it an all appropriate places.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had a copy of the compatibility version of struct timex in each 64 bit
architecture. This patch just creates a global one and replaces all the
usages of the old ones.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jens Axboe <axboe@suse.de>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Acked-by: Alasdair G Kergon <agk@redhat.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/sam/kbuild: (46 commits)
kbuild: remove obsoleted scripts/reference_* files
kbuild: fix make help & make *pkg
kconfig: fix time ordering of writes to .kconfig.d and include/linux/autoconf.h
Kconfig: remove the CONFIG_CC_ALIGN_* options
kbuild: add -fverbose-asm to i386 Makefile
kbuild: clean-up genksyms
kbuild: Lindent genksyms.c
kbuild: fix genksyms build error
kbuild: in makefile.txt note that Makefile is preferred name for kbuild files
kbuild: replace PHONY with FORCE
kbuild: Fix bug in crc symbol generating of kernel and modules
kbuild: change kbuild to not rely on incorrect GNU make behavior
kbuild: when warning symbols exported twice now tell user this is the problem
kbuild: fix make dir/file.xx when asm symlink is missing
kbuild: in the section mismatch check try harder to find symbols
kbuild: fix section mismatch check for unwind on IA64
kbuild: kill false positives from section mismatch warnings for powerpc
kbuild: kill trailing whitespace in modpost & friends
kbuild: small update of allnoconfig description
kbuild: make namespace.pl CROSS_COMPILE happy
...
Trivial conflict in arch/ppc/boot/Makefile manually fixed up
When we stop allocating percpu memory for not-possible CPUs we must not touch
the percpu data for not-possible CPUs at all. The correct way of doing this
is to test cpu_possible() or to use for_each_cpu().
This patch is a kernel-wide sweep of all instances of NR_CPUS. I found very
few instances of this bug, if any. But the patch converts lots of open-coded
test to use the preferred helper macros.
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Kyle McMartin <kyle@parisc-linux.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Christian Zankel <chris@zankel.net>
Cc: Philippe Elie <phil.el@wanadoo.fr>
Cc: Nathan Scott <nathans@sgi.com>
Cc: Jens Axboe <axboe@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that driver_register() returns the number of devices
bound to the driver. In fact, it returns zero for success or a negative
error value.
Nobody uses the return value of of_register_driver() anyway.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/mm/mem.c: In function `add_memory':
arch/powerpc/mm/mem.c:128: warning: assignment makes integer from pointer without a cast
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Quite a long time back, prepare_hugepage_range() replaced
is_aligned_hugepage_range() as the callback from mm/mmap.c to arch code to
verify if an address range is suitable for a hugepage mapping.
is_aligned_hugepage_range() stuck around, but only to implement
prepare_hugepage_range() on archs which didn't implement their own.
Most archs (everything except ia64 and powerpc) used the same
implementation of is_aligned_hugepage_range(). On powerpc, which
implements its own prepare_hugepage_range(), the custom version was never
used.
In addition, "is_aligned_hugepage_range()" was a bad name, because it
suggests it returns true iff the given range is a good hugepage range,
whereas in fact it returns 0-or-error (so the sense is reversed).
This patch cleans up by abolishing is_aligned_hugepage_range(). Instead
prepare_hugepage_range() is defined directly. Most archs use the default
version, which simply checks the given region is aligned to the size of a
hugepage. ia64 and powerpc define custom versions. The ia64 one simply
checks that the range is in the correct address space region in addition to
being suitably aligned. The powerpc version (just as previously) checks
for suitable addresses, and if necessary performs low-level MMU frobbing to
set up new areas for use by hugepages.
No libhugetlbfs testsuite regressions on ppc64 (POWER5 LPAR).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of places set_page_count(page, 1) that don't need to.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In mm_init_ppc64() we calculate the location of the "IO hole", but then
no one ever looks at the value. So don't bother.
That's actually all mm_init_ppc64() does, so get rid of it too.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the command line args to the device tree as /chosen/bootargs.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add /system-id, /model and /compatible to the iSeries device tree.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add strne2a() which converts a string from EBCDIC to ASCII.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make mf_get_rtc(), mf_get_boot_rtc() and mf_set_rtc() static, cause they can
be. We need to move mf_set_rtc() to avoid a forward declaration.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These routines just call through to the mf routines, so point ppc_md straight
at the mf routines. We need to pass the cmd through to mf_reboot to make it
work, but that seems reasonable.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some cleanups in the iSeries code.
- Make mf_display_progress() check mf_initialized rather than the caller.
- Set mf_initialized in mf_init() rather than in setup.c
- Then move mf_initialized into mf.c, the only place it's used.
- Move the mf related logic from iSeries_progress() to mf_display_progress()
- Use a #define to size the pending_event_prealloc array
- Use that define in the initialsation loop rather than sizeof jiggery pokery
- Remove stupid comment(s)
- Mark stuff static and/or __init
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It has been decreed that platform numbers are evil, so as a step in that
direction, replace platform_is_lpar() with a FW_FEATURE_LPAR bit.
Currently FW_FEATURE_LPAR really means i/pSeries LPAR, in the future we might
have to clean that up if we need to be more specific about what LPAR actually
means. But that's another patch ...
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When iommu_init_early_pSeries() was added, ages ago, we forgot to remove
the code that checks /chosen/linux,iommu-off in pSeries_init_early(). We
do it now in iommu_init_early_pSeries().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
htab_bolt_mapping() takes a vstart and pstart parameter, but all but one of
its callers actually pass it vstart and vstart. Luckily before it passes
paddr (calculated from paddr) to the hpte_insert routines it calls
virt_to_abs() (aka. __pa()) on the address, so there isn't actually a bug.
map_io_page() however does pass pstart properly, so currently it's broken
AFAICT because we're calling __pa(paddr) which will get us something very
large. Presumably no one's calling map_io_page() in the right context.
Anyway, change htab_bolt_mapping() callers to properly pass pstart, and then
use it properly in htab_bolt_mapping(), ie. don't call __pa() on it again.
Booted on p5 LPAR, iSeries and Power3.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can plug the boot cpu into its node independently of whether numa
topology is detected. And numa_setup_cpu does the right thing for all
cases now, so remove special-casing for non-numa from the cpu hotplug
callback.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc numa code unconditionally onlines all nodes from 0 to the
highest node id found, regardless of whether cpus or memory are
present in the nodes. This wastes 8K per node and complicates some
cpu and memory hotplug situations, such as adding a resource that
doesn't map to one of the nodes discovered at boot.
Set nodes online as resources are scanned. Fall back to node 0 only
when we're sure this isn't a NUMA machine.
Instead of defaulting to node 0 for cases of hot-adding a resource
which doesn't belong to any initialized node, assign it to the first
online node.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Code to handle Power4's invalid node id (0xffff) is duplicated for cpu
and memory. Better to handle this case in one place --
of_node_to_nid. Overall behavior should be unchanged.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we effectively treat the domain ids given to us by firmare as
logical node ids, make this explicit (basically s/numa_domain/nid/).
No functional changes, only variable and function names are modified.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
map_cpu_to_node does not need to be inline, it is never called in a
hot path.
map_cpu_to_node, numa_setup_cpu, and find_cpu_node can be marked
__cpuinit, as they are never used after boot if CONFIG_HOTPLUG_CPU=n.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add debug statement for map_cpu_to_node; it's useful for cpu hotplug.
Clarify debug statement about not finding the numa reference points
property.
Don't print a meaningless associativity depth (-1) on non-numa systems.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At boot, the numa code is assigning boot_cpuid to node 0
unconditionally. Basically, numa_setup_cpu is being stupid about it,
but this is the minimal fix -- just call numa_setup_cpu(boot_cpuid)
later, after all nodes have been set online.
Signed-off-by: Nathan Lynch <nathanl@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My patch (d7a5b2ffa1) to always panic if
lmb_alloc() fails is broken because it checks alloc < 0, but should be
checking alloc == 0.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Dump a stream of rawbytes with a new 'dr' command.
Produces less output and it is simpler to feed the output to scripts.
Also, dr has no dumpsize limits.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The dynamic add path for PCI Host Bridges can fail to configure children
adapters under P5IOC controllers. It fails to properly fixup bus/device
resources, and it fails to properly enable EEH. Both of these steps
need to occur before any children devices are enabled in
pci_bus_add_devices().
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
remove warnings when building a 64bit kernel.
smp_call_function triggers also with 32bit kernel.
WARNING: vmlinux: duplicate symbol 'smp_call_function' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:164:EXPORT_SYMBOL(smp_call_function);
arch/powerpc/kernel/smp.c:300:EXPORT_SYMBOL(smp_call_function);
WARNING: vmlinux: duplicate symbol 'ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:113:EXPORT_SYMBOL(ioremap);
arch/powerpc/mm/pgtable_64.c:321:EXPORT_SYMBOL(ioremap);
WARNING: vmlinux: duplicate symbol '__ioremap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:117:EXPORT_SYMBOL(__ioremap);
arch/powerpc/mm/pgtable_64.c:322:EXPORT_SYMBOL(__ioremap);
WARNING: vmlinux: duplicate symbol 'iounmap' previous definition was in vmlinux
arch/powerpc/kernel/ppc_ksyms.c:118:EXPORT_SYMBOL(iounmap);
arch/powerpc/mm/pgtable_64.c:323:EXPORT_SYMBOL(iounmap);
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We should be memset'ing the data we are pointing to, not the pointer
itself. This is in an error path so we probably don't hit it much.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes incorrect setting of powersave_nap to 1 on all
PowerMacs, potentially causing memory corruption on some models. This
bug was introuced by me during the 32/64 bits merge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The wording of the CRASH_DUMP Kconfig option is not very clear. It gives you a
kernel that can be used _as_ the kdump kernel, not a kernel that can boot into
a kdump kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable the onboard IDE driver for p610, p615 and p630.
They have the CD connected to this card. All other RS/6000 systems with this
controller have no connectors and dont need this option.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Correct the loop for cacheflush. No idea where I copied the code from,
but the original does not work correct. Maybe the flush is not needed.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent changes to keep gettimeofday in sync with xtime had the side
effect that it was occasionally possible for the time reported by
gettimeofday to go back by a microsecond. There were two reasons:
(1) when we recalculated the offsets used by gettimeofday every 2^31
timebase ticks, we lost an accumulated fractional microsecond, and
(2) because the update is done some time after the notional start of
jiffy, if ntp is slowing the clock, it is possible to see time go backwards
when the timebase factor gets reduced.
This fixes it by (a) slowing the gettimeofday clock by about 1us in
2^31 timebase ticks (a factor of less than 1 in 3.7 million), and (b)
adjusting the timebase offsets in the rare case that the gettimeofday
result could possibly go backwards (i.e. when ntp is slowing the clock
and the timer interrupt is late). In this case the adjustment will
reduce to zero eventually because of (a).
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current pcspkr code combines the device and driver registration.
This patch splits these, putting the device registration in the arch
specific code.
PowerPC and MIPS only have the pcspkr present sometimes.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The lparcfg code needs several things which are pretty arcane internal
details and which we don't want to export, which means that lparcfg
doesn't work when built as a module. This makes it a bool instead of
a tristate in the Kconfig so that users can't try to build it as a
module.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A careful reading of the recent changes to the system call entry/exit
paths revealed several problems, plus some things that could be
simplified and improved:
* 32-bit wasn't testing the _TIF_NOERROR bit in the syscall fast exit
path, so it was only doing anything with it once it saw some other
bit being set. In other words, the noerror behaviour would apply to
the next system call where we had to reschedule or deliver a signal,
which is not necessarily the current system call.
* 32-bit wasn't doing the call to ptrace_notify in the syscall exit
path when the _TIF_SINGLESTEP bit was set.
* _TIF_RESTOREALL was in both _TIF_USER_WORK_MASK and
_TIF_PERSYSCALL_MASK, which is odd since _TIF_RESTOREALL is only set
by system calls. I took it out of _TIF_USER_WORK_MASK.
* On 64-bit, _TIF_RESTOREALL wasn't causing the non-volatile registers
to be restored (unless perhaps a signal was delivered or the syscall
was traced or single-stepped). Thus the non-volatile registers
weren't restored on exit from a signal handler. We probably got
away with it mostly because signal handlers written in C wouldn't
alter the non-volatile registers.
* On 32-bit I simplified the code and made it more like 64-bit by
making the syscall exit path jump to ret_from_except to handle
preemption and signal delivery.
* 32-bit was calling do_signal unnecessarily when _TIF_RESTOREALL was
set - but I think because of that 32-bit was actually restoring the
non-volatile registers on exit from a signal handler.
* I changed the order of enabling interrupts and saving the
non-volatile registers before calling do_syscall_trace_leave; now we
enable interrupts first.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The kbuild system takes advantage of an incorrect behavior in GNU make.
Once this behavior is fixed, all files in the kernel rebuild every time,
even if nothing has changed. This patch ensures kbuild works with both
the incorrect and correct behaviors of GNU make.
For more details on the incorrect behavior, see:
http://lists.gnu.org/archive/html/bug-make/2006-03/msg00003.html
Changes in this patch:
- Keep all targets that are to be marked .PHONY in a variable, PHONY.
- Add .PHONY: $(PHONY) to mark them properly.
- Remove any $(PHONY) files from the $? list when determining whether
targets are up-to-date or not.
Signed-off-by: Paul Smith <psmith@gnu.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
yaboot is scrogged and calls us with an invalid stack alignment,
it seems.
Thanks to David Woodhouse to pointing me to the problem.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Thu, 2006-03-02 at 19:55 +0100, Olaf Hering wrote:
> My iBook1 has 2 memory regions in reg. Depending on how I boot it
> (vmlinux+initrd) or zImage.initrd, it will not boot with current Linus
> tree.
> rmo_top should be 160MB instead of 32MB.
On logically-partitioned machines the first element of the reg
property in the memory node is defined to be the "RMO" region,
i.e. the memory that the processor can access in real mode. On other
machines the first element has no special meaning, so only take it to
be the RMO region on LPAR machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes userland aware of the icache snoop capability of the
POWER5 (and possibly others in the future) and of SMT capabilities.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The variable `timebase' used to transfer the current timebase value
from one cpu to the other in smp_core99_give/take_timebase was only
an unsigned long, i.e. 32 bits on 32-bit machines. It needs to be
64 bits. This makes it a u64, and fixes the issue reported by Kyle
Moffett, that the two cpus see wildly different values for the time
of day.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is along the lines suggested by Chris Lumens but goes further
in that it leaves the DEBUG symbol undefined, making the DBG macro
empty.
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 32-bit, the exception prolog for the program check exception doesn't
enable interrupts early on. If it is an illegal instruction exception,
we read the instruction in order to emulate certain instructions, and
the get_user of the instruction triggers a WARN_ON since interrupts
are still disabled. This adds a local_irq_enable() to enable
interrupts before reading the instruction.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds mm->task_size to keep track of the task size of a given mm
and uses that to fix the powerpc vdso so that it uses the mm task size to
decide what pages to fault in instead of the current thread flags (which
broke when ptracing).
(akpm: I expect that mm_struct.task_size will become the way in which we
finally sort out the confusion between 32-bit processes and 32-bit mm's. It
may need tweaks, but at this stage this patch is powerpc-only.)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before the merge I updated create_pte_mapping() to work for iSeries, by
calling iSeries_hpte_bolt_or_insert. (4c55130b2a)
Later we changed iSeries_hpte_insert to cope with the bolting case, and called
that instead from create_pte_mapping() (which was renamed to htab_bolt_mapping)
(3c726f8dee).
Unfortunately that change introduced a subtle bug, where we pass an absolute
address to iSeries_hpte_insert() where it expects a physical address. This
leads to us calling phys_to_abs() twice on the physical address, which is
seriously bogus.
This only causes a problem if the absolute address from the first translation
can be looked up again in the chunk_map, which depends on the size and layout
of memory. I've seen it fail on one box, but not others.
The minimal fix is to pass the physical address to iSeries_hpte_insert(). For
2.6.17 we should make phys_to_abs() BUG if we try to double-translate an
address.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bug in the assembly code of the vdso can cause gettimeofday() to hang
or to return incorrect results. The wrong register was used to test for
pending updates of the calibration variables and to create a dependency
for subsequent loads. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some hotplug driver functions were migrated to the kernel for use by EEH
in commit 2bf6a8fa21.
Previously, the PCI Hotplug module had been changed to use the new
OFDT-based PCI probe when appropriate:
5fa80fcdca
When rpaphp_pci_config_slot() was moved from the rpaphp driver to the
new kernel function pcibios_add_pci_devices(), the OFDT-based probe
stuff was dropped. This patch restores it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The inline cputime_to_foo and foo_to_cputime conversion functions in
include/asm-powerpc/cputime.h refer to 5 variables, which need to be
exported if those functions are to be usable from modules.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 9ec4b1f356 made kprobes not compile
without module support, so just make that clear in the Kconfig file.
Also, since it's marked EXPERIMENTAL, make that dependency explicit too.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mem= command line option was being ignored in arch/powerpc if we were not
a CONFIG_MULTIPLATFORM (which is handled via prom_init stub). The initial
command line extraction and parsing needed to be moved earlier in the boot
process and have code to actual parse mem= and do something about it.
Also, fixed a compile warning in the file.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maple firmware does not need PCI resource allocation, and in fact, it
can cause problems in some strange cases.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do disable, not enable, the HT APIC IRQ in the function that is
supposed to.
Enable the MPIC IRQ before enabling the downstream APIC IRQ, avoids
potentially losing an interrupt.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update defconfigs for g5, pseries and generic ppc64. Default choices
for everything, with the following exceptions:
* Enable WINDFARM_PM112 on g5 and ppc64.
* Increase CONFIG_NR_CPUS to 4 in g5_defconfig
* CONFIG_TIGON3=y instead of =m in g5_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
HMT support is currently broken and needs to be reworked to play nicely
with the SMT scheduler. Remove the bit rotten bits for the time being.
I also updated an incorrect comment, we enter __secondary_hold with the
physical cpu id in r3.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
native_hpte_clear has a spinlock recursion problem with the native_tlbie_lock
being called twice, once in native_hpte_clear() and once within tlbie().
Fix the problem by changing the call to tlbie() in native_hpte_clear() to
__tlbie(). It still supports only 4k pages for now.
Signed-off-by: R Sharada <sharada@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Disable OProfile in Kconfig for iSeries to prevent hangs. OProfile
was not originally intended to work with legacy iSeries.
Signed-off-by: Kelly Daly <kelly@au.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
altivec_unavailable_exception is called without setting r3... it looks like
the r3 that actually gets passed in as struct pt_regs *regs is the
undisturbed value of r3 at the time the altivec instruction was encountered.
The user actually gets to choose the pt_regs printed in the Oops!
This fixes the oops by passing the correct pt_regs pointer to
altivec_unavailable_exception.
Signed-off-by: Alan Curry <pacman@TheWorld.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The panic CPU is waiting forever due to some large timeout value if some
CPU is not responding to an IPI.
This patch fixes the problem - the maximum waiting period will be
10 seconds and then the kdump boot will go ahead.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For kexec we need to know the size of the MMU hash table.
Currently we calculate the size once in the htab code, and then twice more in
the kexec code, once using htab_hash_mask and once using ppc64_pft_size.
On some machines the ppc64_pft_size calculation is broken because
ppc64_pft_size is not set.
So we need to fix the second calculation, but better still we should just
calculate the size once and use it everywhere else.
Tested on Power5 LPAR, Power4 non-LPAR and Power3.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When I changed the hvlpevent_queue code to use a spinlock instead of a
custom atomic (719d1cd867) I didn't
initialise the lock anywhere, oops.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PCI support for setting PCI from flat device tree on 85xx specifically for
MPC8540 ADS.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some recent PowerBook models tend to lose the ethernet PHY on
suspend/resume. It -seems- that they use a combo ethernet-firewire PHY
chip and the firewire PHY seems to die the same way when that happens. Not
trying to toggle the firewire cable power appears to fix it. So this patch
disables changes to the firewire cable power control GPIO on those models.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the logical and physical cpu ids of a secondary thread don't match, we will
fail to spin the thread up on pSeries machines due to a bug in pseries/smp.c
We call the RTAS "start-cpu" method with the physical cpu id, the address of
pSeries_secondary_smp_init and the value to pass that function in r3. Currently
we pass "lcpu", the logical cpu id, but pSeries_secondary_smp_init expects
the physical cpu id in r3.
We should be passing pcpu instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For UP to SMP kexec to work we need to jump into pSeries_secondary_smp_init
event on a UP + KEXEC kernel. The secondary cpus will not find their hw_cpu_id
in the paca and so they'll jump into kexec_wait, ready for a kexec.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because smp_release_cpus() is built for SMP || KEXEC, it's not safe to
unconditionally call it from setup_system(). On a UP && KEXEC kernel we'll
start up the secondary CPUs which will then go beserk and we die.
Simple fix is to conditionally call smp_release_cpus() in setup_system(). With
that in place we don't need the dummy definition of smp_release_cpus() because
all call sites are #ifdef'ed either SMP or KEXEC.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fallback gracefully when reading /proc/ppc64/lparcfg when the /rtas
device node can't be found.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A few symbols are exported twice, remove them from ppc_ksyms.c
Remove users of sys_ctrler in arch/ppc/
WARNING: vmlinux: duplicate symbol '__delay' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__up' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down_interruptible' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'sys_ctrler' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncat' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncmp' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strrchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strnlen' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strpbrk' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'memscan' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strstr' previous definition was in vmlinux
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a regression which was introduced by moving ppc32 to use
the same sort of lockless gettimeofday as ppc64 has been using for
some time. This involves getting the timebase and performing some
simple arithmetic to convert it to seconds and microseconds. However,
the factor and offset used there weren't being updated when NTP
varied the tick length using adjtimex. 64-bit didn't notice the
problem because it had a hook in the 32-bit adjtimex compat routine
that attempted to work out what the generic timekeeping code would
do and alter the factor and offset to match. However, that code
was very complex and it wasn't clear that it still matched what the
generic code would do.
Now we use the generic current_tick_length() routine that was recently
added to check that the current tick will be as long as we expect; if
not we recompute the factor and offset. This keeps gettimeofday and
xtime in sync. In addition we check that gettimeofday hasn't got ahead
of xtime on each timer interrupt; if it has, we resync.
Signed-off-by: Paul Mackerras <paulus@samba.org>
We are setting up sources for building external modules like this:
/usr/src/linux-obj> # create a .config file
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD oldconfig
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD prepare
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD scripts
/usr/src/linux-obj> make -C /usr/src/linux O=$PWD clean
After that, external modules can be built with:
/usr/src/module> make -C /usr/src/linux-obj M=$PWD
This fails for ppc32 because the `make clean' removes the
arch/powerpc/include directory. This should be done in archmrproper
instead of in archclean.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Embedded boards that u-boot require a kernel image in the uImage format.
This allows a given board to specify it wants a uImage built by default.
This also fixes a warning at config time, as this symbol is referred
to in arch/powerpc/platforms/83xx/Kconfig.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With this patch 'make vmlinux.bin' works. This is needed by
some embedded platforms. Kumar already added the routines
to actually build the image in arch/powerpc/boot/Makefile.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we have some stuff in firmware.h and kernel/firmware.c that is
#ifdef CONFIG_PPC_PSERIES. Move it all into platforms/pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up fw_feature_init in platforms/pseries/setup.c. Clean up white space
and replace the while loop with a for loop - which seems clearer to me.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The e500 core reference manual indicates that isync is required
after mtmsr(DE bit) and mtspr DBCR0. Add isyncs to make the code
conform to the spec.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Ran arch/powerpc/platforms/85xx through Lindent
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename mpc85xx.c to misc.c to match the pattern established by the
8349 port - consistency is a good thing. Also run Lindent on the
file to clean it up.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cut-and-paste from the old platform code in arch/ppc resulted in
arch/powerpc/platforms/85xx/mpc85xx_ads.c having way too many
header files included. Clean this up.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated FP unavailable exception to refer to the correct
function in traps.c. head_booke.h was using the old name, KernelFP,
instead of kernel_fp_unavailable_exception.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Registers system call for the powerpc architecture.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With this, new system calls only have to be wired up in one place
for ARCH=ppc and ARCH=powerpc, rather than 2.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved some code around so its usable by more systems than just
the MPC834x SYS.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Setup the platform devices needed by the Freescale EHCI USB
host controllers based on a flat device tree
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
LMB_ALLOC_ANYWHERE doesn't need to be part of the API, it's only used in
lmb.c - so move it out of the header file.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently most callers of lmb_alloc() don't check if it worked or not, if it
ever does weird bad things will probably happen. The few callers who do check
just panic or BUG_ON.
So make lmb_alloc() panic internally, to catch bugs at the source. The few
callers who did check the result no longer need to.
The only caller that did anything interesting with the return result was
careful_allocation(). For it we create __lmb_alloc_base() which _doesn't_ panic
automatically, a little messy, but passable.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleaned up fsl_soc.c based on comments from Olof Johansson. Ran through
Lindent, and split gfar_mdio init into its own function.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
remove extern declarations of pmac_newworld
move pmac_newworld to bss
if there is any "interrupt-controller" device, then it is newworld.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a cpu is hotplug-onlined, if we don't set per_cpu(last_jiffy) to
something sane, timer_interrupt will execute its while loop for every
tick missed since the cpu was last online (or since the system was
booted, if we're adding a new cpu). This can cause weird hangs, ssh
sessions dropping, and we can even go xmon if we take a global IPI at
the wrong time.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We call unregister_vpa but we don't check to see if the hypervisor
supports this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Anton Blanchard <anton@samba.org>
--
arch/powerpc/platforms/pseries/setup.c | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since 404849bbd2 we've been using
LOAD_REG_ADDRBASE, which uses the toc pointer, in decrementer_iSeries_masked.
This can explode if we take the decrementer interrupt while we're in a module,
because the toc pointer in r2 will be the module's toc pointer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code to mark a page as icache dirty (so that it will later be
icache-dcache flushed when we try to execute from it) is duplicated in
three places: flush_dcache_page() does this marking and nothing else,
but clear_user_page() and copy_user_page() duplicate it, since those
functions make the page icache dirty themselves.
This patch makes those other functions call flush_dcache_page()
instead, so the logic's all in one place. This will make life less
confusing if we ever need to tweak the details of the the lazy icache
flush mechanism.
arch/powerpc/mm/mem.c | 14 ++------------
1 file changed, 2 insertions(+), 12 deletions(-)
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Checking a pointer for NULL before passing it to kfree is pointless, kfree
does its own NULL checking of input.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/kernel/udbg_16550.c: In function `udbg_init_maple_realmode':
arch/powerpc/kernel/udbg_16550.c:162: warning: assignment from incompatible pointer type
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use generic_calibrate_decr to restore missing clock: speed in /proc/cpuinfo
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's possible for prom_init to allocate the flat device tree inside the
kdump crash kernel region. If this happens, when we load the kdump kernel we
overwrite the flattened device tree, which is bad.
We could make prom_init try and avoid allocating inside the crash kernel
region, but then we run into issues if the crash kernel region uses all the
space inside the RMO. The easiest solution is to move the flat device tree
once we're running in the kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It turns out that we can't stop the watchdog from
triggering here. If we touch the timer (which just uses the current jiffie
value) before we enable interrupts, it does nothing because jiffies
are not mass-updated until after we enable interrupts. If we touch the
timer after we enable interrupts, its too late because the softlockup
watchdog will already have triggered. The touch_softlockup_watchdog
call removed below does nothing.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to prod everyone here since this is the only CPU that is
guaranteed to be running after the ibm,suspend-me RTAS call returns.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Correctly return the status from the RTAS call. rtas_call expects
to return the status as a return value.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/kernel/rtas.c is getting hvcall.h via spinlock.h, but when we're
building for UP we don't include spinlock.h.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This addresses two items, which are unlikely to be hit if we
trust drivers.
The first is moving a memory barrier below where the vmerged SG count
is passed back, but before the list is set to end. If those
instructions were reordered, there could be an issue in iommu_unmap_sg().
The second is making sure we terminate the list on the failure case of
iommu_map_sg(). If a driver does not look at the failure return code,
it could pass a ill-formed SG list to iommu_unmap_sg().
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
You can't boot a kdump kernel via OF, not reliably anyway, the kernel being at
32 MB conflicts with the zImage wrapper etc. and it blows up.
It's trivial to check in prom_init though, and this is early enough that we can
actually drop back to OF where a reset-all will get you going again, which is
kinda nice. I think this should go in for 2.6.16.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To prevent problems later in boot, make sure we don't create zero-size lmb
regions.
I've checked all the callers, and at the moment no one should ever hit this.
All callers use a constant size, or they check the computed size before they
call us.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In prom.c we run finish_node() on allnodes twice. The first time we just
calculate how much memory we'll need, the second time we do the actual work.
If the calculation stage determines that we need 0 bytes, then we should skip
the lmb allocation. Although an alloc of zero will work, it has been seen to
lead to a BUG_ON() in reserve_bootmem() on at least one machine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a small fix to get the spufs init sequence right.
init_spu_base() in spu_base.c should be called (via
module_init(init_spu_base)) before spufs_init() (via
module_init(spufs_init)) in spufs/inode.c gets called.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When loading up the FPU, we were using a 'ld' (load doubleword)
instruction to get the FP exception mode from the thread_struct,
but it's only an int field. This changes the ld to lwz (load
word and zero-extend).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Build break: Building PCI hotplug on PowerPC results in
a build break, due to failure to export symbols.
Reported today by Dave Jones <davej@redhat.com>:
drivers/pci/hotplug/rpaphp.ko needs unknown symbol pcibios_add_pci_devices
This patch fixes the break in the arch/powerpc tree.
Next patch fixes same problem in drivers/pci tree
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Better save the sigmask instead of throwing it away so it can be restored.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the platform function interrupt functions actually work. Calls
irq_enable() for the first in the list, and irq_disable() for the last.
Added *func to struct irq_client so the the user can pass just that to
pmf_unregister_irq_client().
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Older pSeries systems with serial ports dont get any console output after
recent changes. CONFIG_ISA does not make sense for CONFIG_PPC_PSERIES
because it enables lots of old drivers. Instead, remove the dependency on
CONFIG_ISA from the serial port discovery code.
Signed-off-by: Olaf Hering <olh@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert: 40727198bf
These PHY changes hang the sungem driver on startup with Sun chips on
sparc64. Hopefully we can redo these changes in a way that doesn't
break non-Apple systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
On my latest laptop, I've had occasional PHY dead on wakeup from
sleep... the PHY would be totally unresponsive even to toggling the hard
reset line until the machine is powered down... Looking closely at the
code, I found some possible issues in the way we setup the MDIO lines
during suspend along with slight divergences from what Darwin does when
resetting it that may explain the problem. That patch change these and
the problem appear to be gone for me at least... I also fixed an mdelay
-> msleep while I was at it to the pmac feature code that is called
when toggling the PHY reset line since sungem doesn't call it in an
atomic context anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>b
Signed-off-by: David S. Miller <davem@davemloft.net>
Embedded boards that u-boot require a kernel image in the uImage format.
This allows a given board to specify it wants a uImage built by default.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement the TIF_RESTORE_SIGMASK flag in the new arch/powerpc kernel, for
both 32-bit and 64-bit system call paths.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The TIF_RESTORE_SIGMASK flag allows us to have a generic implementation of
sys_rt_sigsuspend() instead of duplicating it for each architecture. This
provides such an implementation and makes arch/powerpc use it.
It also tidies up the ppc32 sys_sigsuspend() to use TIF_RESTORE_SIGMASK.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the ability to disability packet split at compile time and use the legacy receive path on PCI express hardware. Made this a CONFIG option and modified the Kconfig, to reflect the new option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When I removed the powermac support from arch/ppc/kernel/pci.c,
I overlooked the fact that that file is used in 32-bit ARCH=powerpc
builds. To prevent problems in future, restore the original version
of that file as arch/powerpc/kernel/pci_32.c, and use that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Noticed in 2.6.15-git9 that CRASH_DUMP option is moved to top level.
Moved CRASH_DUMP into "kernel options" next to KEXEC and this config
option supports only for PPC64 at this time.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The changes to the device node structure broke Maple build. This fixes it.
Unfortunately I coudn't test as my Maple board appears to be dead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
- This contains the arch specific changes for the following the
kdump generic fixes which were already accepted in the upstream.
. Capturing CPU registers (for the case of 'panic' and invoking
the dump using 'sysrq-trigger') from a function (stack frame) which will
be not be available during the kdump boot. Hence, might result in
invalid stack trace.
. Dynamically allocating per cpu ELF notes section instead of
statically for NR_CPUS.
- Fix the compiler warning in prom_init.c.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Miboot images are apparently still used on some old 32-bit powermacs,
so build them with ARCH=powerpc if we're 32-bit and powermac support
is enabled.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The first generation of PCI powermacs had a host bridge called /chaos
which was for all intents and purposes a PCI host bridge, but has a
device_type of "vci" in the device tree (presumably it's not really
PCI at the hardware level or something).
The OF parsing stuff in arch/powerpc/kernel/prom_parse.c currently
doesn't recognize it as a PCI bridge, which means that controlfb.c
can't get its device addresses.
This makes prom_parse.c recognize a device_type of "vci" as indicating
a PCI host bridge. With this, controlfb works again.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 601 processor will generate an alignment exception for accesses
which cross a page boundary. In the boot wrapper code, OF is still
handling all exceptions, and it doesn't have an alignment exception
handler that emulates the instruction and continues.
This changes the memcpy and memmove routines in the boot wrapper to
avoid doing unaligned accesses. If the source and destination are
misaligned with respect to each other, we just copy one byte at a
time.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds code to build zImage.coff and/or zImage.initrd.coff when
CONFIG_PPC32 and CONFIG_PPC_PMAC are defined. It also restructures
the OF client code and adds some workarounds for OF quirks on the
older machines.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes CHRP build again, although it's untested because my Pegasos
is currently in pieces.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handle the ibm,suspend-me RTAS call specially. It needs
to be wrapped in a set of synchronization hypervisor calls
(H_Join). When the H_Join calls are made on all CPUs, the
intent is that only one will return with H_Continue, meaning
that he is the "last man standing". That CPU then issues the
ibm,suspend-me call. What is interesting, of course, is that
the CPU running when the rtas syscall is made, may NOT be the
CPU that ultimately executes the ibm,suspend-me rtas call.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the first MPC83xx board that uses a flat device tree to arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Parse the flat device tree for devices on Freescale SOC's that we know
about (gianfar, gianfar_mdio, i2c, mpc83xx_wdt). We need to setup
platform devices and platform data for these devices to match arch/ppc
usage.
Also add a helper function (get_immrbase) that reports the base
address of the MMIO registers on the SOC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On a number of embedded reference boards there isn't always a
way to reset, power_off, or halt the board. Rather than having
each board implement a spin loop just let the generic code do
it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In 2.6.15-git6 a change was commited in the oprofile support in
the powerpc architecture. It introduced the powerpc_oprofile_type
which contains the define G4. This causes a name clash with the
existing wacom usb tablet driver.
CC [M] drivers/usb/input/wacom.o
drivers/usb/input/wacom.c:98: error: conflicting types for `G4'
include/asm/cputable.h:37: error: previous declaration of `G4'
CC [M] drivers/usb/mon/mon_text.o
make[3]: *** [drivers/usb/input/wacom.o] Error 1
make[2]: *** [drivers/usb/input] Error 2
The elements of an enum declared in global scope are effectivly
global identifiers themselves. As such we need to ensure the names
are unique. This patch updates the later oprofile support to use
unique names.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The glibc folks want to use AT_PLATFORM to select between possible
alternative versions of shared libraries. This commit makes the kernel
supply an AT_PLATFORM string that indicates what class of processor
we are running on. Processors with the same set of user-level
instructions and roughly the same instruction scheduling characteristics
are given the same AT_PLATFORM value; for example, 821, 823 and 860
are all reported as "ppc823", and 7447, 7447A, 7448, 7450, 7451, 7455
are all called "ppc7450".
The intention is that the AT_PLATFORM values match the values that
gcc accepts for the -mcpu= option. For values which are numeric
(e.g. -mcpu=750), "ppc" has been prepended.
This also adds a PPC_FEATURE_BOOKE bit to the AT_HWCAP value and sets
it for the 440 family and the Freescale 85xx family.
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present the lppaca - the structure shared with the iSeries
hypervisor and phyp - is contained within the PACA, our own low-level
per-cpu structure. This doesn't have to be so, the patch below
removes it, making a separate array of lppaca structures.
This saves approximately 500*NR_CPUS bytes of image size and kernel
memory, because we don't need aligning gap between the Linux and
hypervisor portions of every PACA. On the other hand it means an
extra level of dereference in many accesses to the lppaca.
The patch also gets rid of several places where we assign the paca
address to a local variable for no particular reason.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates the variety of macros used for loading 32 or
64-bit constants in assembler (LOADADDR, LOADBASE, SET_REG_TO_*). The
idea is to make the set of macros consistent across 32 and 64 bit and
to make it more obvious which is the appropriate one to use in a given
situation. The new macros and their semantics are described in the
comments in ppc_asm.h.
In the process, we change several places that were unnecessarily using
immediate loads on ppc64 to use the GOT/TOC. Likewise we cleanup a
couple of places where we were clumsily subtracting PAGE_OFFSET with
asm instructions to use assemble-time arithmetic or the toreal() macro
instead.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following reworks how defaultimage- is used. We default to zImage
here and then override it on platforms that need something more (uImage
in the future) or less (vmlinux on iSeries).
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support to reconfigure the device tree through the existing
proc filesystem interface. Add "add_property", "remove_property",
and "update_property" commands to the existing interface.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add an of_find_property function that returns a struct property
given a property name. Then change the get_property function to
use that routine internally.
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for updating and removing device tree
properties. Since we hand out pointers to properties with gay
abandon, we can't just free the property storage. Instead we
move deleted, or the old copy of an updated property, to a
"dead properties" list.
Also note, its not feasable to kref device tree properties.
we call get_property() all over the kernel in a wild variety
of contexts.
One consequence of this change is that we now take a
read_lock(&devtree_lock) when doing get_property().
Signed-off-by: Dave Boutcher <sleddog@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the documentation no longer tells people to 'make bzImage', and
with the previous patch nothing more than 'make' is required to get the
right bootable images (just like on i386 now), this removes the bzImage
-> zImage target redirect on ARCH=powerpc
Signed-off-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 5388fb1025 made signal_32.c
use discard_lazy_cpu_state, which broke ARCH=ppc because that
uses the common signal_32.c but has its own process.c. Make ARCH=ppc
use the common process.c to fix this and to reduce the amount
of duplicated code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
These symbols are only used in the file that they are defined in,
so they should not be in the global namespace.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These symbols are only used in the file that they are defined in,
so they should not be in the global namespace.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pmac_setup_arch is only used in the file that it is defined in,
so it should not be in the global namespace.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These symbols are only used in the file that they are defined in,
so they should not be in the global namespace.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rpn is assigned every time in the loop, no need to increase it too.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pcibios_claim_one_bus is not needed on iSeries and phbs_remap_io can be
mode static.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There was a function declared for CONFIG_PSERIES which no longer exists
and the two function declarations for CONFIG_ISERIES have been moved
into an include file in platforms/iseries since they are defined and
used only there.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts part of "ppc64 iSeries: allow build with no PCI"
(145d01e428) which affected generic code
and applies a fix in the arch specific code.
Commit "partly merge iseries do_IRQ"
(5fee9b3b39eb55c7e3619a3b36ceeabffeb8f144) introduced iSeries_get_irq
which was only available if CONFIG_PCI is set.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Fixed memory reserve map layout
The memory reserve map is suppose to be a pair of 64-bit integers
to represent each region. On ppc32 the code was treating the
pair as two 32-bit integers. Additional the prom_init code was
producing the wrong layout on ppc32.
Added a simple check to try to provide backwards compatibility.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove warning in eeh code about mixed variables and code.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Heikki Lindholm pointed out that there was a potential race with the
lazy CPU state (FP, VR, EVR) stuff if preempt is enabled. The race
is that in the process of restoring FP state on sigreturn, the task
gets preempted by a user task that wants to use the FPU. It will take
an FP unavailable exception, which will write the current FPU state
to the thread_struct, overwriting the values which sigreturn has
stored. Note that this can only happen on UP since we don't implement
lazy CPU state on SMP.
The fix is to flush the lazy CPU state before updating the
thread_struct. To do this we re-use the flush_lazy_cpu_state()
function from process.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window where a probe gets removed right after the probe is hit
on some different cpu. In this case probe handlers can't find a matching
probe instance related to break address. In this case we need to read the
original instruction at break address to see if that is not a break/int3
instruction and recover safely.
Previous code had a bug where we were not checking for the above race in
case of reentrant probes and the below patch fixes this race.
Tested on IA64, Powerpc, x86_64.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/powerpc/kernel/crash.c isn't safe for PPC32 (yet?), so don't build it.
Built with CONFIG_KEXEC=y for pmac32_defconfig, pseries_defconfig,
and g5_defconfig.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
clean-files was being set twice rather than being appended to.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
iSeries doesn't need to set the htab_address explicitly, htab_initialize()
will do it for us later.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To make iSeries just a teensy bit less special, create ibm,pft-size properties
in the iSeries device tree. We can then rely on htab_dt_scan_pftsize() to set
ppc64_pft_size for us.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated Kconfig & Makefiles in prep for adding support for the Freescale
MPC83xx family of processors to arch/powerpc. Moved around some config
options that are more globally applicable to other PowerPC processors.
Added a temporary config option (83xx) to match existing arch/ppc support
for the MPC83xx line.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPE Book IV indicates that MFC DMA operations must be
suspended and restored on SPU context switch (in Step 8).
This patch adds that operation, which is missing from the
current spufs implementation.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the compilation error (shown below) when CONFIG_SMP=n.
arch/powerpc/kernel/crash.c: In function `crash_kexec_prepare_cpus':
arch/powerpc/kernel/crash.c:236: error: implicit declaration of
function `smp_release_cpus'
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current ppc64 per cpu data implementation is quite slow. eg:
lhz 11,18(13) /* smp_processor_id() */
ld 9,.LC63-.LCTOC1(30) /* per_cpu__variable_name */
ld 8,.LC61-.LCTOC1(30) /* __per_cpu_offset */
sldi 11,11,3 /* form index into __per_cpu_offset */
mr 10,9
ldx 9,11,8 /* __per_cpu_offset[smp_processor_id()] */
ldx 0,10,9 /* load per cpu data */
5 loads for something that is supposed to be fast, pretty awful. One
reason for the large number of loads is that we have to synthesize 2
64bit constants (per_cpu__variable_name and __per_cpu_offset).
By putting __per_cpu_offset into the paca we can avoid the 2 loads
associated with it:
ld 11,56(13) /* paca->data_offset */
ld 9,.LC59-.LCTOC1(30) /* per_cpu__variable_name */
ldx 0,9,11 /* load per cpu data
Longer term we can should be able to do even better than 3 loads.
If per_cpu__variable_name wasnt a 64bit constant and paca->data_offset
was in a register we could cut it down to one load. A suggestion from
Rusty is to use gcc's __thread extension here. In order to do this we
would need to free up r13 (the __thread register and where the paca
currently is). So far Ive had a few unsuccessful attempts at doing that :)
The patch also allocates per cpu memory node local on NUMA machines.
This patch from Rusty has been sitting in my queue _forever_ but stalled
when I hit the compiler bug. Sorry about that.
Finally I also only allocate per cpu data for possible cpus, which comes
straight out of the x86-64 port. On a pseries kernel (with NR_CPUS == 128)
and 4 possible cpus we see some nice gains:
total used free shared buffers cached
Mem: 4012228 212860 3799368 0 0 162424
total used free shared buffers cached
Mem: 4016200 212984 3803216 0 0 162424
A saving of 3.75MB. Quite nice for smaller machines. Note: we now have
to be careful of per cpu users that touch data for !possible cpus.
At this stage it might be worth making the NUMA and possible cpu
optimisations generic, but per cpu init is done so early we have to be
careful that all architectures have their possible map setup correctly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds Kconfig entries to control the early debugging options,
currently in setup_64.c.
Doing this via Kconfig rather than #defines means you can have one source tree,
which is buildable for multiple platforms - and you can enable the correct
early debug option for each platform via .config.
I made udbg_early_init() a static inline because otherwise GCC is to daft to
optimise it away when debugging is off.
Now that we have udbg_init_rtas() we can make call_rtas_display_status* static.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Connect iSeries up to the standard early debugging infrastructure.
To actually use this you need to enable the iSeries early debugging
in setup_64.c. Then after the messages are logged hit Ctrl-x Ctrl-x on
your console to dump the Hypervisor console buffer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RPAPHP hoplug driver will not build as a module, because it calls
on a pcibios routine which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changes to the serial driver to remove flip buffers have broken the serial
jsm driver. It doesn't even compile anymore. The jsm driver was enabled
in only one defconfig - ppc64. In order to keep defconfigs building,
disable CONFIG_SERIAL_JSM for the time being.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch (against 2.6.15-rc5-mm3) fixes a kprobes build break
due to changes introduced in the kprobe locking in 2.6.15-rc5-mm3. In
addition, the patch reverts back the open-coding of kprobe_mutex.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently arch_remove_kprobes() is only implemented/required for x86_64 and
powerpc. All other architecture like IA64, i386 and sparc64 implementes a
dummy function which is being called from arch independent kprobes.c file.
This patch removes the dummy functions and replaces it with
#define arch_remove_kprobe(p, s) do { } while(0)
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on some feedback from Oleg Nesterov, I have made few changes to
previously posted patch.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since Kprobes runtime exception handlers is now lock free as this code path is
now using RCU to walk through the list, there is no need for the
register/unregister{_kprobe} to use spin_{lock/unlock}_isr{save/restore}. The
serialization during registration/unregistration is now possible using just a
mutex.
In the above process, this patch also fixes a minor memory leak for x86_64 and
powerpc.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that all these entries in the arch ioctl32.c files are gone [1], we can
build fs/compat_ioctl.c as a normal object and kill tons of cruft. We need a
special do_ioctl32_pointer handler for s390 so the compat_ptr call is done.
This is not needed but harmless on all other architectures. Also remove some
superflous includes in fs/compat_ioctl.c
Tested on ppc64.
[1] parisc still had it's PPP handler left, which is not fully correct
for ppp and besides that ppp uses the generic SIOCPRIV ioctl so it'd
kick in for all netdevice users. We can introduce a proper handler
in one of the next patch series by adding a compat_ioctl method to
struct net_device but for now let's just kill it - parisc doesn't
compile in mainline anyway and I don't want this to block this
patchset.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment in compat.c is wrong, every architecture provides a
get_compat_sigevent() for the IPC compat code already.
This basically moves the x86_64 version to common code and removes all the
others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds back the call to pci_cfg_space_size() when building the PCI
tree from OF nodes that was commented out due to the function not being
exported by the PCI code. It's now exported, so let's use it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Matthew Wilcox wondered why we need these functions. We don't.
Remove them and just use the "normal" versions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous change by Kumar Gala in this area led to legacy_serial.c
and udbg_16550.c being built as modules when CONFIG_SERIAL_8250=m.
Fix this by introducing a new symbol, CONFIG_PPC_UDBG_16550, to
control whether these files get built, and arrange for it to be selected
for those platforms that need it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a crash on null-pointer deref during dlpar slot addition.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 1c87c0f84943fbbc91826967ff4fea1b059a526f commit)
<asm/systemcfg.h> is gone now, and the PCI error recovery constants
in include/linux/pci.h changed their names in the process of getting
accepted.
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 5a2516156c591fc3d2059fbd93f97e15eb6010d6 commit)
242-eeh-no-percpu-counters.patch
Remove per-cpu counters from the EEH code. These statistics counters
are incremented at a very low frequency, and the performance gains of
per-cpu variables are negligable. By contrast, the counters weren't
safe against cpu off/online operations, and its not worth the effort
to make them so (other than to turn them into plain globals).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from be3b5d1be053ccb41e91fa5a6f43ef5db301357d commit)
241-eeh-save-bars-earlier.patch
Save the PCI device bars *before* any PCI probing is done.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 76c902b919098860f3d4e125f847abcc4cb1782a commit)
240-ioremap-null-ptr-test.patch
Under highly unusual circumstances, a buggy driver will ask a null ptr
to be ioremapped, an operation that curently succeeds but leads to
later trouble. Instead, refuse to remap the null pointer.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e71d9e598533c1889e7162f5f4647e5d378c102c commit)
239-eeh-multifunction-consolidate.patch
New-style firmware will often place multiple different functions
under a non-EEH-aware parent. However, these devices might share
a common PE "partition endpoint" and config address, ad thus any
EEH events will affect all of the devices in common. This patch
makes the effort to find all of these common devices and handle
them together.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 216810296bb97d39da8e176822e9de78d2f00187 commit)
238-eeh-stop-if-reset_failed.patch
If the firmware is unable to reset the PCI slot for some reason, then
don't attempt any further recovery steps after that point. Instead,
mark the device as permanently failed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e06b942521eb2cdaf232726f45a820d5837acb12 commit)
237-eeh-bridge-token.patch
Minor: the rtas-bridge token should be set up the same way that all
the other rtas tokens are set up.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 78379b6c5fc17b6666c40b05988e6708e98479c0 commit)
236-eeh-config-addr.patch
The PE configuration address wasn't being cnsistently used in all locations
where a config address is called for. This patch adds it to the places it
should have appeared in.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from c2bc904a28095aca0b04a37854b63b78622a032e commit)
235-eeh-set-pcidev-bugfix.patch
The pci device field of the pci_dn struct should be initialized to a
valid value.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from beb45c93d494a11c36e5b24f638e610db8428b54 commit)
234-eeh-find-pe.patch
The find_device_pe() routine is duplicated in two files. Remove one of
the two copies, declare the other extern.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 48408e708282d4d0269136ff27ea5acbd9410b5a commit)
26-eeh-partition-endpoint.patch
New versions of firmware introduce a new method by which the
"partitionable endpoint" (the point at which the pci bus is cut)
should be located. This code adds the support for this (mandatory)
new feature.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 9fcfb5d35b5294659f9299aa9cae6fd16325c07e commit)
25-pci-address-cache.patch
The core EEH file is rather large. This patch splits out a self-contained
chunk of it into its own file. This is the chunk that performes the
caching and lookup of pci devices based on the i/o addresses of thier
resoures. This code is almos architecture-independent and could be
used by any system that wanted to find a pci device based only on
the i/o address used by the device.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from b0b291d59906d4a9a89ed9e34d9fd684c7188924 commit)
Various PCI bus errors can be signaled by newer PCI controllers. The
core error recovery routines are architecture dependent. This patch adds
a recovery infrastructure for the PPC64 pSeries systems.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from e8ca11b460c4c9c7fa6b529be221529ebd770e38 commit)
This patch converts the inode semaphore to a mutex. I have tested it on
XFS and compiled as much as one can consider on an ia64. Anyway your
luck with it might be different.
Modified-by: Ingo Molnar <mingo@elte.hu>
(finished the conversion)
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We don't set CONFIG_PPC_MULTIPLATFORM on iSeries (yet). Avoid
compiling in the prom_init stuff on iSeries.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In add_memory() we should be using __va() to get a virtual address.
Spotted by Mike Kravetz.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The CONFIG_PPC_OF symbol is used to mean that the firmware device tree
access functions are available. Since we always have a device tree
with ARCH=powerpc, make CONFIG_PPC_OF always Y for ARCH=powerpc.
This fixes some compile errors reported by Kumar Gala, but in a
different way to his patch. This also makes prom_parse.o be compiled
only if CONFIG_PPC_OF so that non-OF ARCH=ppc platforms will compile.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When taking a DABR exception we were reporting the PC. It makes more
sense to report the address that caused the exception, and the gdb guys
would like it that way.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
POWER5+ adds new PMU groups and as such needs to be treated differently
by oprofile userspace. Change it to report itself as power5+.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My recent changes to oprofile broke it when built as a module. Fix it by
using an enum instead of a function pointer. This way we still retain
the oprofile configuration in the cputable.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds cpufreq support for all desktop "tower" G5 models. The
only G5 models still lacking cpufreq support at this point are the
Xserve and possibly the new iMac iSight (not tested). I'll have those
added soon. That patch uses the new platform functions interpreter to
implement frequency and voltage switching on most models.
Note that in order to find the low frequency value, I had to hack
something that might now work properly on all models, so if the
frequency value reported when running low speed looks bogus to you,
please report it to me. (Appart from a bogus reported value, things
should work fine).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the platform function interpreter itself along with the backends
for UniN/U3/U4, mac-io, GPIOs and i2c. It adds the ability to execute
those do-platform-* scripts in the device-tree (at least for most
devices for which a backend is provided). This should replace the clock
spreading hacks properly. It might also have an impact on all sort of
machines since some of the scripts marked "at init" will now be executed
on boot (or some other on sleep/wakeup), those will possibly do things
that the kernel didn't do at all, like setting some values into some i2c
devices (changing thermal sensor calibration or conversion rate) etc...
Thus regression testing is MUCH welcome. Also loook for errors in dmesg.
That's also why I've left rather verbose debugging enabled in this
version of the patch.
(I do expect some Windtunnel G4s to show some errors as they have an i2c
clock chip on the PMU bus that uses some primitives that the i2c backend
doesn't implement yet. I really need users that have one of those
machine to come back to me so we can get that done right, though the
errors themselves should be harmless, I suspect the machine might not
run at full speed).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the continuation of the previous patch. This one removes the old
PowerMac i2c drivers (i2c-keywest and i2c-pmac-smu) and replaces them
both with a single stub driver that uses the new PowerMac low i2c layer.
Now that i2c-keywest is gone, the low-i2c code is extended to support
interrupt driver transfers. All i2c busses now appear as platform
devices. Compatibility with existing drivers should be maintained as the
i2c bus names have been kept identical, except for the SMU bus but in
that later case, all users has been fixed.
With that patch added, matching a device node to an i2c_adapter becomes
trivial.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the first part of a rework of the PowerMac i2c code. It
completely reworks the "low_i2c" layer. It is now more flexible,
supports KeyWest, SMU and PMU i2c busses, and provides functions to
match device nodes to i2c busses and adapters.
This patch also extends & fix some bugs in the SMU driver related to i2c
support and removes the clock spreading hacks from the pmac feature code
rather than adapting them to the new API since they'll be replaced by
the platform function code completely in patch 3/5
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc64 has its own version of sys_time. It looks pretty scary, touching
a whole bunch of variables without any locking or memory ordering.
In fact, a recent bugreport has shown it can actually go backwards. Time
to remove it and just use the generic sys_time, which is implemented on
top of do_gettimeofday.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For far, all SPU triggered interrupts always end up on
the first SMT thread, which is a bad solution.
This patch implements setting the affinity to the
CPU that was running last when entering execution on
an SPU. This should result in a significant reduction
in IPI calls and better cache locality for SPE thread
specific data.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One local variable is missing an __iomem modifier,
in another place, we pass a completely unused argument
with a missing __user modifier.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In a hypervisor based setup, direct access to the first
priviledged register space can typically not be allowed
to the kernel and has to be implemented through hypervisor
calls.
As suggested by Masato Noguchi, let's abstract the register
access trough a number of function calls. Since there is
currently no public specification of actual hypervisor
calls to implement this, I only provide a place that
makes it easier to hook into.
Cc: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Cc: Geoff Levand <geoff.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The logic for sys_spu_run keeps growing and it does
not really belong into file.c any more since we
moved away from using regular file operations to our
own syscall.
No functional change in here.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
checking bits manually might not be synchonized with
the use of set_bit/clear_bit. Make sure we always use
the correct bitops by removing the unnecessary
identifiers.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If creating one entry failed in spufs_fill_dir,
we never cleaned up the freshly created entries.
Fix this by calling the cleanup function on error.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If get_unused_fd failed in sys_spu_create, we never cleaned
up the created directory. Fix that by restructuring the
error path.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When spu_activate fails in spu_acquire_runnable, the
state must still be SPU_STATE_SAVED, we were
incorrectly setting it to SPU_STATE_RUNNABLE.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During an earlier cleanup, we lost the serialization
of multiple spu_run calls performed on the same
spu_context. In order to get this back, introduce a
mutex in the spu_context that is held inside of spu_run.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only checking for SPUFS_MAGIC is not reliable, because
it might not be unique in theory. Worse than that,
we accidentally allow spu_run to be performed on
any file in spufs, not just those returned from
spu_create as intended.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spu_forget will do mmput on the DMA address space,
which can lead to lots of other stuff getting triggered.
We better not hold a semaphore here that we might
need in the process.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to check for validity of owner under down_write,
down_read is not enough.
Noticed by Al Viro.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch enables support for pause(0) power management state
for the Cell Broadband Processor, which is import for power efficient
operation. The pervasive infrastructure will in the future enable
us to introduce more functionality specific to the Cell's
pervasive unit.
From: Maximino Aguilar <maguilar@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Only build in support for ISA and PCI cases if we have enabled CONFIG_ISA
and CONFIG_PCI. Additionally, isa_bridge is a global so we shouldn't use
it a parameter name since it gets redefined to NULL when !CONFIG_PCI.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, we are not looking at all interrupt controller nodes in the
device tree even though the proper node was not found. This is causing
the system panic. The attached patch will scan all nodes until it finds
the proper interrupt controller type.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In setup_arch and setup_system call find_legacy_serial_ports() if we
build in support for 8250 serial ports instead of basing it on PPC_MULTIPLATFORM.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added a common udbg_progress for use by ppc_md.progress()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the ability to configure and initialize legacy 8250 serials
ports on an SOC bus. Also, fixed an issue that we would not
configure any serial ports if "linux,stdout-path" was not found.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The checking of the baudrate in udbg_probe_uart_speed was
too tight and would cause reporting back of the default
baud rate in cases where the computed speed was valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The system will oops if an attempt is made to add memory to an
empty node/zone. This patch prevents adding memory to an empty
node. The code to dynamically add a node/zone is non-trivial.
This patch is temporary and will be removed when the ability
to dynamically add a node/zone is complete.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Building the arch/powerpc tree currently gives me
two warnings with gcc-4.0:
arch/powerpc/mm/imalloc.c: In function '__im_get_area':
arch/powerpc/mm/imalloc.c:225: warning: 'tmp' may be used uninitialized in this function
arch/powerpc/mm/hugetlbpage.c: In function 'hugetlb_get_unmapped_area':
arch/powerpc/mm/hugetlbpage.c:608: warning: unused variable 'vma'
both fixes are trivial.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Configurable 16-bit UID and friends support
This allows turning off the legacy 16 bit UID interfaces on embedded platforms.
text data bss dec hex filename
3330172 529036 190556 4049764 3dcb64 vmlinux-baseline
3328268 529040 190556 4047864 3dc3f8 vmlinux
From: Adrian Bunk <bunk@stusta.de>
UID16 was accidentially disabled for !EMBEDDED.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ptrace_get_task_struct() helper that I added as part of the ptrace
consolidation is useful in variety of places that currently opencode it.
Switch them to the common helpers.
Add a ptrace_traceme() helper that needs to be explicitly called, and simplify
the ptrace_get_task_struct() interface. We don't need the request argument
now, and we return the task_struct directly, using ERR_PTR() for error
returns. It's a bit more code in the callers, but we have two sane routines
that do one thing well now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oops, forgot to compile the VMALLOCBASE/VMALLOC_START patch on
iSeries. VMALLOC_START is defined in pgtable.h whereas previously
VMALLOCBASE was previously defined in page.h. lparmap.c needs to be
updated appropriately.
Booted on iSeries RS64 (now).
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds oprofile support for the 7450 and all its multitudinous
derivatives.
* Added 7450 (and derivatives) support for oprofile
* Changed e500 cputable to have oprofile model and cpu_type fields
* Added support for classic 32-bit performance monitor interrupt
* Cleaned up common powerpc oprofile code to be as common as possible
* Cleaned up oprofile_impl.h to reflect 32 bit classic code
* Added 32-bit MMCRx bitfield definitions and SPR numbers
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes pci_address_to_pio() to return an unsigned long (to be safe)
and fixes a bug in the implementation that caused it to return a bogus
IO port number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64, we independently define VMALLOCBASE and VMALLOC_START to be
the same thing: the start of the vmalloc() area at 0xd000000000000000.
VMALLOC_START is used much more widely, including in generic code, so
this patch gets rid of the extraneous VMALLOCBASE.
This does require moving the definitions of region IDs from page_64.h
to pgtable.h, but they don't clearly belong in the former rather than
the latter, anyway. While we're moving them, clean up the definitions
of the REGION_IDs:
- Abolish REGION_SIZE, it was only used once, to define
REGION_MASK anyway
- Define the specific region ids in terms of the REGION_ID()
macro.
- Define KERNEL_REGION_ID in terms of PAGE_OFFSET rather than
KERNELBASE. It amounts to the same thing, but conceptually this is
about the region of the linear mapping (which starts at PAGE_OFFSET)
rather than of the kernel text itself (which is at KERNELBASE).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch enabling the new G5's with U4 broke initialization of the DART
driver, causing it to trigger a BUG_ON for a case that is actually
valid. This patch fixes it:
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds some very basic support for the new machines, including the
Quad G5 (tested), and other new dual core based machines and iMac G5
iSight (untested). This is still experimental ! There is no thermal
control yet, there is no proper handing of MSIs, etc.. but it
boots, I have all 4 cores up on my machine. Compared to the previous
version of this patch, this one adds DART IOMMU support for the U4
chipset and thus should work fine on setups with more than 2Gb of RAM.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is code in the RPAPHP directory that is identical to this routine;
I'll be removing that code in an upcoming patch, but this patch is needed
to expose the function to make it callable.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup the MPIC IO-APIC workarounds, make them a bit more generic,
smaller and faster.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pre-parsed addrs/n_addrs fields in struct device_node are finally
gone. Remove the dodgy heuristics that did that parsing at boot and
remove the fields themselves since we now have a good replacement with
the new OF parsing code. This patch also fixes a bunch of drivers to use
the new code instead, so that at least pmac32, pseries, iseries and g5
defconfigs build.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a defconfig for PowerMac with ARCH=powerpc
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove a comment in head.S which is no longer relevant.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We used to print a NUMA cpu summary at boot before the hotplug cpu code
was added. This has been useful for catching machine configuration as
well as firmware bugs in the past.
This patch restores that functionality. An example of the output is:
Node 0 CPUs: 0-7
Node 1 CPUs: 8-15
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
/dev/nvram uses the user-provided read/write size
for kmalloc, which fails, if a large number is passed.
This will always use a single page at most, which
can be expected to succeed.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently crash in the fedora installer because the keyboard
driver tries to access I/O space that is not there on our hardware.
This uses the same solution as powermac by just marking all
legacy i/o as invalid.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
So far, the iommu code was hardwired to a linear mapping
between 0x20000000 and 0x40000000, so it could only support
512MB of RAM.
This patch still keeps the linear mapping, but looks for
proper ibm,dma-window properties to set up larger windows,
this makes the maximum supported RAM size 2GB.
If there is anything unusual about the dma-window properties,
we fall back to the old behavior.
We also support switching off the iommu completely now
with the regular iommu=off command line option.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Output from hexdump with "%08x" depends on HOST platform's endian.
When building linux by cross toolchain, that difference makes errors.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoff.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of my last patches contained a broken line
from splitting out some other changes, this
restores a working version.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One of the two users of spufs_calls.owner still has a race
when calling try_module_get while the module is removed.
This makes it use the correct instance of owner.
Noticed by Milton Miller.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I can't really get a conclusive answer from the firmware
people what to check for, so I just try scanning for
anything that starts with "IBM,CPB", which should be
correct for all hardware produced so far and for
systemsim.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handling mailbox interrupts was broken in multiple respects,
the combination of which was hiding the bugs most of the time.
- The ibox interrupt mask was open initially even though there
are no waiters on a newly created SPU.
- Acknowledging the mailbox interrupt did not work because
it is level triggered and the mailbox data is never retrieved
from inside the interrupt handler.
- The interrupt handler delivered interrupts with a disabled
mask if another interrupt is triggered for the same class
but a different mask.
- The poll function did not enable the interrupt if it had not
been enabled, so we might run into the poll timeout if none of
the other bugs saved us and no signal was delivered.
We probably still have a similar problem with blocking
read/write on mailbox files, but that will result in extra
wakeup in the worst case, not in incorrect behaviour.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reduces lock complexity of SPU scheduler, particularly
for involuntary preemptive switches. As a result the new code
does a better job of mapping the highest priority tasks to SPUs.
Lock complexity is reduced by using the system default workqueue
to perform involuntary saves. In this way we avoid nasty lock
ordering problems that the previous code had. A "minimum timeslice"
for SPU contexts is also introduced. The intent here is to avoid
thrashing.
While the new scheduler does a better job at prioritization it
still does nothing for fairness.
From: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes it easier to preempt an SPU context by
having the scheduler hold ctx->state_sema for much shorter
periods of time.
As part of this restructuring, the control logic for the "run"
operation is moved from arch/ppc64/kernel/spu_base.c to
fs/spufs/file.c. Of course the base retains "bottom half"
handlers for class{0,1} irqs. The new run loop will re-acquire
an SPU if preempted.
From: Mark Nutter <mnutter@us.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
spufs is rather noisy when debugging is enabled, this
turns off the messages for production use.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
try_module_get returns true when NULL arguments, so
we first need to check if there is a module loaded before
getting the reference count.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the new rules for reserved pages, the spufs now
needs working page reference counting.
I should probably look into converting to vm_insert_page,
but for now this patch makes spufs work again.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes all exported symbols of spufs to EXPORT_SYMBOL_GPL.
The spu_ibox_read/spu_wbox_write symbols are not exported
any more when the scheduler patch is applied.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Milton has proposed that we should support a "linux,usable-memory" property
on memory nodes which describes, in preference to "reg", the regions of memory
Linux should use.
This facility is required for kdump to inform the second kernel which memory
it should use.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds code to parse and setup the crash kernel resource in the
first kernel. PPC64 ignores the @x part, we always run at 32 MB.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implementing the machine_crash_shutdown which will be called by
crash_kexec (called in case of a panic, sysrq etc.). Disable the
interrupts, shootdown cpus using debugger IPI and collect regs
for all CPUs.
elfcorehdr= specifies the location of elf core header stored by
the crashed kernel. This command line option will be passed by
the kexec-tools to capture kernel.
savemaxmem= specifies the actual memory size that the first kernel
has and this value will be used for dumping in the capture kernel.
This command line option will be passed by the kexec-tools to
capture kernel.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a few places where we need to fix things up for the kernel to work
if it's linked at 32MB:
- platforms/powermac/smp.c
To start secondary cpus on pmac we patch the reset vector, which is fine.
Except if we're above 32MB we don't have enough bits for an absolute branch,
it needs to relative.
- kernel/head_64.s
- A few branches in the cpu hold code need to load the full target address
and do a bctr.
- after_prom_start needs to load PHYSICAL_START as the dest address, not 0.
- The exception prolog needs to load the low word of the target adddress,
not just the low halfword.
- Fixup handling of the initial stab address.
- kernel/setup_64.c
smp_release_cpus() needs to write 1 to the spinloop flag near 0, not 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Regardless of where the kernel's linked we always get interrupts at low
addresses. This patch creates a trampoline in the first 3 pages of memory,
where interrupts land, and patches those addresses to jump into the real
kernel code at PHYSICAL_START.
We also need to reserve the trampoline code and a bit more in prom.c
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The fwnmi vectors can be anywhere < 32 MB, so we need to use a trampoline
for them. The kdump kernel will register the trampoline addresses, which will
then jump up to the real code above 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a Kconfig variable, CONFIG_CRASH_DUMP, which configures the
built kernel for use as a Kdump kernel.
Currently "all" this involves is changing the value of KERNELBASE to 32 MB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows iSeries to build again. It just moves pci_address_to_pio
outside the #ifdef CONFIG_PPC_MULTIPLATFORM.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Minor: use macro to perform void pointer deref; this may someday help
avoid pointer typecasting errors.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This places dynamically added memory within the appropriate
numa node. A new routine hot_add_scn_to_nid() replicates most of
the memory scanning code in parse_numa_properties().
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch separates usage of KERNELBASE and PAGE_OFFSET. I haven't
looked at any of the PPC32 code, if we ever want to support Kdump on
PPC we'll have to do another audit, ditto for iSeries.
This patch makes PAGE_OFFSET the constant, it'll always be 0xC * 1
gazillion for 64-bit.
To get a physical address from a virtual one you subtract PAGE_OFFSET,
_not_ KERNELBASE.
KERNELBASE is the virtual address of the start of the kernel, it's
often the same as PAGE_OFFSET, but _might not be_.
If you want to know something's offset from the start of the kernel
you should subtract KERNELBASE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a bunch of code that compares an address with KERNELBASE to see if
it's a "kernel address", ie. >= KERNELBASE. The proper test is actually to
compare with PAGE_OFFSET, since we're going to change KERNELBASE soon.
So replace all of them with an is_kernel_addr() macro that does that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently machine_crash_shutdown() gets a struct pt_regs, but doesn't pass it
through to the ppc_md function, it should.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we select ppc32 under the powerpc architecture we get the
error below. This relates to defining distribute_irqs when this
configuratiom option is undefined.
CC arch/powerpc/sysdev/mpic.o
.../arch/powerpc/sysdev/mpic.c: In function `mpic_setup_this_cpu':
.../arch/powerpc/sysdev/mpic.c:788: error: `CONFIG_IRQ_ALL_CPUS'
undeclared (first use in this function)
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up the currently available memory models for ppc32 under
the powerpc architecture. We need FLATMEM for ppc32: enable it.
SPARSEMEM is not parameterised for ppc32 so disable that. Take this
opportunity to clean up white space for FLATMEM_ENABLE.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Here is an updated version of the patch that panics if no memory is
found as Nathan suggested. I'm still concerned that panic strings
(not just the one added here) at this stage of booting do not show
up on my system. But, that is an issue separate from this patch.
Combine get_mem_*_cells() routines to avoid multiple memory node
lookups. Added missing of_node_put() call. Changed variable names
to help with some confusion as to meaning.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the OF address parsers to return the IO flags
indicating the type of address obtained. It also adds a PCI
call for converting physical addresses that hit IO space into
into IO tokens, and add routines that return the translated
addresses into struct resource
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The udbg low level io layer has an issue with udbg_getc() returning a
char (unsigned on ppc) instead of an int, thus the -1 if you had no
available input device could end up turned into 0xff, filling your
display with bogus characters. This fixes it, along with adding a little
blob to xmon to do a delay before exiting when getting an EOF and fixing
the detection of ADB keyboards in udbg_adb.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When compiling without BOOTX_TEXT the following warning is emitted.
Fix up the definition to only be made when required.
CC arch/powerpc/platforms/powermac/udbg_adb.o
.../arch/powerpc/platforms/powermac/udbg_adb.c:41: warning:
`udbg_adb_use_btext' defined but not used
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
udbg_adb_init() has become dependent on btext_drawchar, even when
BOOTX_TEXT support is not selected. This leads to the error below.
Make the check dependant on BOOTX_TEXT.
LD .tmp_vmlinux1
arch/powerpc/platforms/built-in.o(.toc1+0xa40): undefined
reference to `btext_drawchar'
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
23-rpaphp-migrate.patch (parts)
This patch moves some pci device add & remove code from the PCI
hotplug directory to the arch/powerpc/kernel directory, and cleans
it up a tad. The primary reason for this is that the code performs
some fairly generic operations that are shared with the PCI error
recovery code (living in the arch/powerpc/kernel directory).
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
22-rpaphp-eliminate-dupe-code.patch (parts)
The RPAPHP code contains two routines that appear to be gratuitous
copies of very similar pci code. In particular,
rpaphp_claim_resource ~~ pci_claim_resource
rpadlpar_claim_one_bus == pcibios_claim_one_bus
This makes pcibios_claim_one_bus from arch/powerpc/kernel/pci_64.c
available to the RPAPHP code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
20-rpaphp-eeh-cleanup.patch
This patch move some code from the rpaphp directory, to the powerpc
directory, where it should have been all along (Among other things, I
need it in the powerpc directory for the PCI error recovery.)
Please note that patch affects TWO maintainers: Paul, after applying
the powerpc part, please ask that GregKH appli the PCI part. It is safe
to have the powerpc part go in first. It would be bad to have the
PCI part go in first.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I started to add missing of_node_put() calls to the routines that
determine the number of cells for memory. Decided to combine the
routines instead of making separate node lookups. Changed variable
names to help with some confusion as to meaning.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the new serial probe code with some PCI MMIO UARTs, and fixes
CHRP build with ARCH=powerpc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Thu, 2005-11-24 at 12:51 +0000, David Woodhouse wrote:
> Somehow this one slipped through the cracks; when we ended up in
> do_signal() on a 32-bit kernel but without having the caller-saved
> registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
> ensure they got saved later.
Oh, and if we actually set the flag, then we fairly quickly find out
that I was a bit overzealous in copying code from entry_64.S ... :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Somehow this one slipped through the cracks; when we ended up in
do_signal() on a 32-bit kernel but without having the caller-saved
registers into the regs, we didn't set the TIF_SAVE_NVGPRS flag to
ensure they got saved later.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, 2005-11-22 at 15:49 +1100, Benjamin Herrenschmidt wrote:
> This moves the discovery of legacy serial ports to a separate file,
> makes it common to ppc32 and ppc64, and reworks it to use the new OF
> address translators to get to the ports early. This new version can also
> detect some PCI serial cards using legacy chips and will probably match
> those discovered port with the default console choice.
This makes it deal with the fact that the Pegasos firmware reports that
its clock frequency is zero...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My previous patches inadvertently broke building a G5 kernel with
CONFIG_XMON enabled. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes several unnecessary fields from the paca:
- next_jiffy_update_tb was simply unused. Remove trivially.
- The exdsi exception save area was not used. There were plans to use
it, but they never seem to have gone anywhere. If they ever do, we
can put it back. Remove from the paca, and from asm-offsets.c
- The default_decr field was used from asm, but was only ever assigned
the value of tb_ticks_per_jiffy. Just access tb_ticks_per_jiffy from
asm directly instead.
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On iSeries, the paca contains, amongst other things an ItLpRegSave
structure used by the hypervisor to save registers. The hypervisor
locates this area through a pointer at the beginning of the paca, so
the structure itself can be located elsewhere. This patch moves the
reg_save area out into its own array. This reduces the amount of
iSeries specific gunk which is visible to general powerpc code via
paca.h
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the powerpc version of hugetlb_get_unmapped_area() entirely
ignores the hint address. The only way to get a hugepage mapping at a
specified address is with MAP_FIXED, in which case there's no way
(short of parsing /proc/self/maps) for userspace to tell if it will
clobber an existing mapping. This is inconvenient, so the patch below
makes hugepage mappings use the given hint address if possible.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Sam Ravnborg pointed out that calling if_changed was redundant in the
rule since a prerequisite had to have changed for us to get there.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Add support for building uImages
Add support to build a kernel image bootable by u-boot.
Most of the makefile foo is taken from arch/ppc/boot/images/Makefile
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Encode the sub bus number into the real irq number (even though it
is always zero for now) so that we have enough information to do
the EOI in iseries_end_IRQ.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
ARCH=powerpc couldn't boot from BootX as it uses a "different" way of
getting in the kernel. This patch adds the necessary trampolines,
creating a flattened device-tree from the tree passed from MacOS, and
initializing the btext engine early for really-early debugging.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch unifies udbg for both ppc32 and ppc64 when building the
merged achitecture. xmon now has a single "back end". The powermac udbg
stuff gets enriched with some ADB capabilities and btext output. In
addition, the early_init callback is now called on ppc32 as well,
approx. in the same order as ppc64 regarding device-tree manipulations.
The init sequences of ppc32 and ppc64 are getting closer, I'll unify
them in a later patch.
For now, you can force udbg to the scc using "sccdbg" or to btext using
"btextdbg" on powermacs. I'll implement a cleaner way of forcing udbg
output to something else than the autodetected OF output device in a
later patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the discovery of legacy serial ports to a separate file,
makes it common to ppc32 and ppc64, and reworks it to use the new OF
address translators to get to the ports early. This new version can also
detect some PCI serial cards using legacy chips and will probably match
those discovered port with the default console choice.
Only ppc64 gets udbg still yet, unifying udbg isn't finished yet.
It also adds some speed-probing code to udbg so that the default console
can come up at the same speed it was set to by the firmware.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Parsing addresses extracted from Open Firmware isn't a simple matter. We
have various bits of code that try to do it in various place, including
some heuristics in prom.c that pre-parse addresses at boot and fill
device-nodes "addrs", but those are dodgy at best and I want to
deprecate them. So this patch introduces a new set of routines that
should be capable of parsing most types of addresses and translating
them into CPU physical addresses. It currently works for things on PCI
busses and ISA busses and should work on "standard" busses like the root
bus or the MacIO bus that don't put funky flags in addresses. If you
have other bus types that do use funky flags, you'll have to add new bus
type translators, which is fairly easy.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Tue, 2005-11-15 at 18:52 +0000, David Woodhouse wrote:
> This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
> and brings the ppc32 and ppc64 code slightly closer together.
Needs this unless your binutils, like mine, are clever enough to notice
my stupidity and fix it up automatically...
Spotted by Paul.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a scheduler for SPUs to make it possible to use
more logical SPUs than physical ones are present in the
system.
Currently, there is no support for preempting a running
SPU thread, they have to leave the SPU by either triggering
an event on the SPU that causes it to return to the
owning thread or by sending a signal to it.
This patch also adds operations that enable accessing an SPU
in either runnable or saved state. We use an RW semaphore
to protect the state of the SPU from changing underneath
us, while we are holding it readable. In order to change
the state, it is acquired writeable and a context save
or restore is executed before downgrading the semaphore
to read-only.
From: Mark Nutter <mnutter@us.ibm.com>,
Uli Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the source code that is used to generate spu_save_dump.h and
spu_restore_dump.h. Since a full spu tool chain is needed to
generate these files, the default remains to use the shipped
versions in order to keep the number of tools for building the
kernel down.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the code needed to perform a context switch from
spufs, following the recommended 76-step sequence.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add some infrastructure for saving and restoring the context of an
SPE. This patch creates a new structure that can hold the whole
state of a physical SPE in memory. It also contains code that
avoids races during the context switch and the binary code that
is loaded to the SPU in order to access its registers.
The actual PPE- and SPE-side context switch code are two separate
patches.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the current version of the spu file system, used
for driving SPEs on the Cell Broadband Engine.
This release is almost identical to the version for the
2.6.14 kernel posted earlier, which is available as part
of the Cell BE Linux distribution from
http://www.bsc.es/projects/deepcomputing/linuxoncell/.
The first patch provides all the interfaces for running
spu application, but does not have any support for
debugging SPU tasks or for scheduling. Both these
functionalities are added in the subsequent patches.
See Documentation/filesystems/spufs.txt on how to use
spufs.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the necessary core bus support used by device drivers
that sit on the IBM GX bus on modern pSeries machines like the Galaxy
infiniband for example. It provide transparent DMA ops (the low level
driver works with virtual addresses directly) along with a simple bus
layer using the Open Firmware matching routines.
Signed-off-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
and brings the ppc32 and ppc64 code slightly closer together.
The ppc64 code was checking current_thread_info()->flags twice in the
syscall exit path; once for TIF_SYSCALL_T_OR_A before disabling
interrupts, and then again for TIF_SIGPENDING|TIF_NEED_RESCHED etc after
disabling interrupts. Now we do the same as ppc32 -- check the flags
only once in the fast path, and re-enable interrupts if necessary in the
ptrace case.
The patch abolishes the 'syscall_noerror' member of struct thread_info
and replaces it with a TIF_NOERROR bit in the flags, which is handled in
the slow path. This shortens the syscall entry code, which no longer
needs to clear syscall_noerror.
The patch adds a TIF_SAVE_NVGPRS flag which causes the syscall exit slow
path to save the non-volatile GPRs into a signal frame. This removes the
need for the assembly wrappers around sys_sigsuspend(),
sys_rt_sigsuspend(), et al which existed solely to save those registers
in advance. It also means I don't have to add new wrappers for ppoll()
and pselect(), which is what I was supposed to be doing when I got
distracted into this...
Finally, it unifies the ppc64 and ppc32 methods of handling syscall exit
directly into a signal handler (as required by sigsuspend et al) by
introducing a TIF_RESTOREALL flag which causes _all_ the registers to be
reloaded from the pt_regs by taking the ret_from_exception path, instead
of the normal syscall exit path which stomps on the callee-saved GPRs.
It appears to pass an LTP test run on ppc64, and passes basic testing on
ppc32 too. Brief tests of ptrace functionality with strace and gdb also
appear OK. I wouldn't send it to Linus for 2.6.15 just yet though :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the EXPORT_SYMBOL'ed but completely unused variable
ucSystemType and removes the unneeded EXPORT_SYMBOL(_prep_type).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This was causing some ordering problems. Remove the up-front evaluation
and just revaluate the compiler version each time we need it.
(The up-front evaluation was problematic because some architectures modify
the value of $(CC)).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Leave the overloaded "hotplug" word to susbsystems which are handling
real devices. The driver core does not "plug" anything, it just exports
the state to userspace and generates events.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sonny has noticed hotplug CPU on ppc64 is broken in 2.6.15-*. One of the
problems is that htab_initialize_secondary is called when a cpu is being
brought up, but it is marked __init.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that commit f9bd170a87
broke the cascade from XICS to i8259 on pSeries machines; specifically
we ended up not ever doing the EOI on the XICS for the cascade. The
result was that interrupts from the serial ports (and presumably any
other devices using ISA interrupts) didn't get through. This fixes
it and also simplifies the code, by doing the EOI on the XICS in the
xics_get_irq routine after reading and acking the interrupt on the
i8259.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't restore the volatile registers in the syscall exit
path, we need to make sure we don't leak any potentially interesting
values from the kernel to userspace. This was already the case for
all except r11. This makes it use r11 for an MSR value, so r11 will
have an (uninteresting) MSR value in it on return to userspace.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When multiple probes are registered at the same address and if due to some
recursion (probe getting triggered within a probe handler), we skip calling
pre_handlers and just increment nmissed field.
The below patch make sure it walks the list for multiple probes case.
Without the below patch we get incorrect results of nmissed count for
multiple probe case.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code that sets the clock spreading feature of the Intrepid ASIC
must not be run on some machine models or those won't boot. This
fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On ppc64, when opening a new hugepage region, we need to make sure any
old normal-page SLBs for the area are flushed on all CPUs. There was
a bug in this logic - after putting the new hugepage area masks into
the thread structure, we copied it into the paca (read by the SLB miss
handler) only on one CPU, not on all. This could cause incorrect SLB
entries to be loaded when a multithreaded program was running
simultaneously on several CPUs. This patch corrects the error,
copying the context information into the PACA on all CPUs using the mm
in question before flushing any existing SLB entries.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On most powerpc CPUs, the dcache and icache are not coherent so
between writing and executing a page, the caches must be flushed.
Userspace programs assume pages given to them by the kernel are icache
clean, so we must do this flush between the kernel clearing a page and
it being mapped into userspace for execute. We were not doing this
for hugepages, this patch corrects the situation.
We use the same lazy mechanism as we use for normal pages, delaying
the flush until userspace actually attempts to execute from the page
in question.
Tested on G5.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cache info is setup by walking the device tree in initialize_cache_info().
However, icache_flush_range might be called before that, in
slb_initialize()->patch_slb_encoding, which modifies the load immediate
instructions used with SLB fault code.
Not only that, but depending on memory layout, we might take SLB faults
during unflatten_device_tree. So that fault will load an SLB entry that
might not contain the right LLP flags for the segment.
Either we can walk the flattened device tree to setup cache info, or
we can pick the known defaults that are known to work. Doing it in the
flattened device tree is hairier since we need to know the machine type
to know what property to look for, etc, etc.
For now, it's just easier to go with the defaults. Worst thing that
happens from it is that we might waste a few cycles doing too small
dcbst/icbi increments.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some debug code wasn't properly removed from the initial 64k pages
patch, and while it's harmless, it's also slowing down significantly a
very hot code path, thus it should really be removed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 64k pages patch changed the meaning of one argument passed to the
low level hash functions (from "large" it became "psize" or page size
index), but one of the call sites wasn't properly updated, causing
potential random weird problems with huge pages. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This bug exists in the current code and prevents machines from booting
with numa enabled if there is a node that does not contain memory.
Workaround is to boot with 'numa=off'. Looks like a simple typo.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's never been a hardware platform that has both pSeries/RPA LPAR
hypervisor and stab (pre-POWER4 segment management). This removes
the redundant code in stab_initalize().
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The previous commit will use the page-at-a-time hypervisor call for
setting up IOMMU entries when we are using 64k pages and setting up
one 64k page, even though that means 16 calls to the hypervisor, since
the hypervisor still works on 4k pages. This optimizes this case by
using the multi-page IOMMU setup hypervisor call instead.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Must adjust tcenum and npages by TCE_PAGE_FACTOR to convert between
64KB pages and TCE (4K) pages. (This is done in other places, except
for this one location.)
Signed-off-by: Michal Ostrowski <mostrows at watson ibm com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the correct pointer to clear the memory of the return values,
to prevent stack corruption in the callers stackframe.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a bug noticed by Paolo Galtieri and fixed for ARCH=ppc in
the previous commit (ppc: fix floating point register corruption).
This fixes the arch/powerpc code by adding preempt_disable/enable,
and also cleans it up a bit by pulling out the code that discards
any lazily-switched CPU register state into a new function, rather
than having that code repeated in three places.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Both 32-bit and 64-bit use the same inline flush_icache_range definition
now, so both need to export __flush_icache_range, not just 64-bit.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This replaces the (in my opinion horrible) VM_UNMAPPED logic with very
explicit support for a "remapped page range" aka VM_PFNMAP. It allows a
VM area to contain an arbitrary range of page table entries that the VM
never touches, and never considers to be normal pages.
Any user of "remap_pfn_range()" automatically gets this new
functionality, and doesn't even have to mark the pages reserved or
indeed mark them any other way. It just works. As a side effect, doing
mmap() on /dev/mem works for arbitrary ranges.
Sparc update from David in the next commit.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Blah. The patch [0] I recently sent fixing errors with
in_hugepage_area() and prepare_hugepage_range() for powerpc itself has
an off-by-one bug. Furthermore, the related functions
touches_hugepage_*_range() and within_hugepage_*_range() are also
buggy. Some of the bugs, like those addressed in [0] originated with
commit 7d24f0b8a5 where we tweaked the
semantics of where hugepages are allowed. Other bugs have been there
essentially forever, and are due to the undefined behaviour of '<<'
with shift counts greater than the type width (LOW_ESID_MASK could
return non-zero for high ranges with the right congruences).
The good news is that I now have a testsuite which should pick up
things like this if they creep in again.
[0] "powerpc-fix-for-hugepage-areas-straddling-4gb-boundary"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With the removal of include/asm-powerpc, we no longer need
arch/powerpc/include/asm for the 64 bit build. We also do not need
-Iarch/powerpc for the 64 bit build either.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 7d24f0b8a5 fixed bugs in the ppc64 SLB
miss handler with respect to hugepage handling, and in the process tweaked
the semantics of the hugepage address masks in mm_context_t.
Unfortunately, it left out a couple of necessary changes to go with that
change. First, the in_hugepage_area() macro was not updated to match,
second prepare_hugepage_range() was not updated to correctly handle
hugepages regions which straddled the 4GB point.
The latter appears only to cause process-hangs when attempting to map such
a region, but the former can cause oopses if a get_user_pages() is
triggered at the wrong point. This patch addresses both bugs.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug in kprobes that can cause an Oops or even a crash when a return
probe is installed on one of the following functions: sys_execve,
do_execve, load_*_binary, flush_old_exec, or flush_thread. The fix is to
remove the call to kprobe_flush_task() in flush_thread(). This fix has
been tested on all architectures for which the return-probes feature has
been implemented (i386, x86_64, ppc64, ia64). Please apply.
BACKGROUND
Up to now, we have called kprobe_flush_task() under two situations: when a
task exits, and when it execs. Flushing kretprobe_instances on exit is
correct because (a) do_exit() doesn't return, and (b) one or more
return-probed functions may be active when a task calls do_exit(). Neither
is the case for sys_execve() and its callees.
Initially, the mistaken call to kprobe_flush_task() on exec was harmless
because we put the "real" return address of each active probed function
back in the stack, just to be safe, when we recycled its
kretprobe_instance. When support for ppc64 and ia64 was added, this safety
measure couldn't be employed, and was eventually dropped even for i386 and
x86_64. sys_execve() and its callees were informally blacklisted for
return probes until this fix was developed.
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Restore an earlier mod which went missing in the powerpc reshuffle: the 4xx
mmu_mapin_ram does not need to take init_mm.page_table_lock.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update comments (only) on page_table_lock and mmap_sem in arch/powerpc.
Removed the comment on page_table_lock from hash_huge_page: since it's no
longer taking page_table_lock itself, it's irrelevant whether others are; but
how it is safe (even against huge file truncation?) I can't say.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Email address update, changing old work address to personal (permanent)
one.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Although we tend to associate VM_RESERVED with remap_pfn_range, quite a few
drivers set VM_RESERVED on areas which are then populated by nopage. The
PageReserved removal in 2.6.15-rc1 changed VM_RESERVED not to free pages in
zap_pte_range, without changing those drivers not to set it: so their pages
just leak away.
Let's not change miscellaneous drivers now: introduce VM_UNPAGED at the core,
to flag the special areas where the ptes may have no struct page, or if they
have then it's not to be touched. Replace most instances of VM_RESERVED in
core mm by VM_UNPAGED. Force it on in remap_pfn_range, and the sparc and
sparc64 io_remap_pfn_range.
Revert addition of VM_RESERVED to powerpc vdso, it's not needed there. Is it
needed anywhere? It still governs the mm->reserved_vm statistic, and special
vmas not to be merged, and areas not to be core dumped; but could probably be
eliminated later (the drivers are probably specifying it because in 2.4 it
kept swapout off the vma, but in 2.6 we work from the LRU, which these pages
don't get on).
Use the VM_SHM slot for VM_UNPAGED, and define VM_SHM to 0: it serves no
purpose whatsoever, and should be removed from drivers when we clean up.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were using udelay in the loop on the primary cpu waiting for the
secondary cpu to take the timebase value. Unfortunately now that
udelay uses the timebase, and the timebase is stopped at this point,
the udelay never terminated. This fixes it by not using udelay, and
increases the number of loops before we time out to compensate.
Signed-off-by: Paul Mackerras <paulus@samba.org>
