ioatdma by default is in snoop mode. Relaxed ordering according to spec
does not do anything in snoop mode. However, it causes hang or significant
performance degrade when tested with NTB. Disabling in the driver due to
some BIOS do not configure it correctly.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the following DT description would result in dmac0 always
being tried first and dmac1 second if dmac0 was unavailable. This
results in heavier use of dmac0 then of dmac1. This patch adds an
approximate average distribution over the two nodes lessening the load
of anyone of them.
i2c6: i2c@e60b0000 {
...
dmas = <&dmac0 0x77>, <&dmac0 0x78>,
<&dmac1 0x77>, <&dmac1 0x78>;
dma-names = "tx", "rx", "tx", "rx";
...
};
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When the ccerr handler is called but the error registers indicate no error
events we need to command eDMA to re-evaluate the errors. Otherwise we can
receive flood of error interrupts.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When check for capabilities recognize slave support by either DMA_SLAVE or
DMA_CYCLIC bit set. If we don't do that the user can't get a normally worked
DMA support for engines that doesn't have one of the mentioned bits set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dma_pool_zalloc combines dma_pool_alloc and memset 0. The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression d,e;
statement S;
@@
d =
- dma_pool_alloc
+ dma_pool_zalloc
(...);
if (!d) S
- memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dma_pool_zalloc combines dma_pool_alloc and memset 0. The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression d,e;
statement S;
@@
d =
- dma_pool_alloc
+ dma_pool_zalloc
(...);
if (!d) S
- memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dma_pool_zalloc combines dma_pool_alloc and memset 0. The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression d,e;
statement S;
@@
d =
- dma_pool_alloc
+ dma_pool_zalloc
(...);
if (!d) S
- memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Keep the entire platform data in the struct dw_dma.
It makes the driver a bit cleaner.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There several changes are done here:
- Convert the property to be in bytes
Besides that this is a common practice for such property, the use of a value
in bytes much more convenient than handling the encoded one.
- Rename data_width to data-width in the device tree bindings
The change leaves the support for the old format as well just in case someone
will use a newer kernel with an old device tree blob.
- While here, replace dwc_fast_ffs() by __ffs()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The value of nr_masters equal to 0 is invalid since this DMA controller has to
have at least one master.
Check this before we proceed with the rest of properties.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix typo in warning message that there is no "interrupt-names"
property defined in the device-tree and legacy-mode is used.
Also added newline to end of message.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch changes the driver to allocate DMA descriptors when
needed. This stops memory resources to be wasted and letting
them sit idle in the free_list structure when the device doesn't
need it... This also solves the problem, that a driver has to
guess the number of how many descriptors it needs to allocate
in advance. Currently, the dma engine will just fail when put
under load by sata_dwc_460ex.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use platform_get_irq_byname to allow for correct mapping of
interrupts to dma channels.
The currently implemented device tree is unfortunately
implemented with the wrong assumption, that each dma-channel
has its own dma channel, but dma-irq 11 is handling
dma-channel 11-14 and dma-irq 12 is actually a "catch all"
interrupt.
So here we use the byname variant and require that interrupts
are explicitly named via the interrupts-name property in the
device tree.
The use of shared interrupts is also implemented.
As a side-effect this means we can now use dma channels 12, 13 and 14
in a correct manner - also testing shows that onl using
channels 11 to 14 for spi and i2s works perfectly (when playing
some video)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Also added check for an error condition in bcm2835_dma_create_cb_chain
that showed up during development of this patch.
Tested using dmatest for all enabled channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add slave_sg support to bcm2835-dma using shared allocation
code for bcm2835_desc and DMA-control blocks already used by
dma_cyclic.
Note that bcm2835_dma_callback had to get modified to support
both modes of operation (cyclic and non-cyclic).
Tested using:
* Hifiberry I2S card (using cyclic DMA)
* fb_st7735r SPI-framebuffer (using slave_sg DMA via spi-bcm2835)
playing BigBuckBunny for audio and video.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bcm2835 dma system has 2 basic types of dma-channels:
* "normal" channels
* "light" channels
Lite channels are limited in several aspects:
* internal data-structure is 128 bit (not 256)
* does not support BCM2835_DMA_TDMODE (2D)
* DMA length register is limited to 16 bit.
so 0-65535 (not 0-65536 as mentioned in the official datasheet)
* BCM2835_DMA_S/D_IGNORE are not supported
The detection of the type of mode is implemented by looking at
the LITE bit in the DEBUG register for each channel.
This allows automatic detection.
Based on this the maximum block size is set to (64K - 4) or to 1G
and this limit is honored during generation of control block
chains. The effect is that when a LITE channel is used more
control blocks are used to do the same transfer (compared
to a normal channel).
As there are several sources/target DREQS that are 32 bit wide
we need to have the transfer to be a multiple of 4 as this would
break the transfer otherwise.
This is why the limit of (64K - 4) was chosen over the
alternative of (64K - 4K).
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In preparation of adding slave_sg functionality this patch moves the
generation/allocation of bcm2835_desc and the building of
the corresponding DMA-control-block chain from bcm2835_dma_prep_dma_cyclic
into the newly created method bcm2835_dma_create_cb_chain.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In preparation to consolidating code we move the cyclic member
into the bcm_2835_desc structure.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add additional defines describing the DMA registers
as well as adding some more documentation to those registers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The original patch contained 3 dma channels that were masked out.
These - as far as research and discussions show - are a
artefacts remaining from the downstream legacy dma-api.
Right now down-stream still includes a legacy api used only
in a single (downstream only) driver (bcm2708_fb) that requires
2D DMA for speedup (DMA-channel 0).
Formerly the sd-card support driver also was using this legacy
api (DMA-channel 2), but since has been moved over to use
dmaengine directly.
The DMA-channel 3 is already masked out in the devicetree in
the default property "brcm,dma-channel-mask = <0x7f35>;"
So we can remove the whole masking of DMA channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
bcm2835-dma supports residue reporting at burst level but didn't report
this via the residue_granularity field.
See also:
b015555327
for the downstream patch.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To be sure we have the cyclic transfers already gone we set cdesc to NULL. It
will prevent the double free.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Residue is a property of any active descriptor. So, any descriptor may be in
different state but residue is a feature of active descriptor. Check if the
asked descriptor is active and return proper residue value for it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Covert dwc->initialized to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Convert dwc->paused to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code is fixed to satisfy a compiler otherwise we have
drivers/dma/dw/core.c: In function ‘dwc_handle_cyclic’:
drivers/dma/dw/core.c:568: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_tasklet’:
drivers/dma/dw/core.c:590: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_off’:
drivers/dma/dw/core.c:1103: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_cyclic_free’:
drivers/dma/dw/core.c:1469: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_probe’:
drivers/dma/dw/core.c:1574: warning: comparison between signed and unsigned
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since struct dw_dma is allocated and regs member is assigned properly we can
use standard IO accessors to the DMA registers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The datasheet requires that the LLP_[SD]_EN bits be cleared whenever
LLP.LOC is zero, i.e. in the last descriptor of a multi-block chain.
Make the driver do this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The LMS field indicates from which master the descriptor is to be
read. This patch assumes this is always the same as the memory
side in a peripheral transfer which is true for all known systems.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the DMA controller uses a different byte order than the host CPU,
the hardware linked list descriptor fields need to be byte-swapped.
This patch makes the driver write these fields using the same byte
order it uses for mmio accesses to the DMA engine. I do not know
if this is guaranteed to always be correct.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On some architectures the DMA controller can have two masters connected to
different buses and thus access to memory is possible only through one and
to peripheral through the other.
This patch changes the src and dst master setting to match the direction
of the transfer.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 8950052029 ("dmaengine: dw: apply both HS interfaces and remove
slave_id usage") cleaned up the code to avoid usage of depricated slave_id
member of generic slave configuration.
Meanwhile it broke the master selection by removing important call to
dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from
custom slave configuration to the internal channel structure.
Everything works until now since there is no customized connection of
DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use.
The configurations where 2 masters are connected to the different masters are
not working anymore. We are expecting one user of such configuration and need
to select masters properly. Besides that it is obviously a performance
regression since only one master is in use in multi-master configuration.
Select masters in accordance with what user asked for. Keep this patch in a form
more suitable for back porting.
We are safe to take necessary data in ->device_alloc_chan_resources() because
we don't support generic slave configuration embedded into custom one, and thus
the only way to provide such is to use the parameter to a filter function which
is called exactly before channel resource allocation.
While here, replase BUG_ON to less noisy dev_warn() and prevent channel
allocation in case of error.
Fixes: 8950052029 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit ef859312c3 ("dmaengine: core: Use dev_ functions for debug and
error prints") wasn't quite right in __dma_request_channel() by claiming
that all pr_ prints have valid DMA channel pointer. Obviously it is not
true as __dma_request_channel() is looking for a channel and returns NULL
if it does not find it.
Prevent this potential NULL pointer dereference by reverting back to
pr_debug().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_get_slave_caps() API only checked for slave capability where
we use slave capabilities for cyclic dma operations as well, so we
should add the cyclic case here too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This tells, for example, IOMMU what the maximum size of a segment
the DMA controller can send.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The timeout capability is only available on the so called DMA write channels,
i.e. associated with UART Rx FIFO. It means we don't need to check the
direction of the channel to handle timeouts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current code allows only up to 3 descriptors to be programmed to the hardware
since it is used wrong calculations. Change % to min_t() to allow as many
descriptors as user supplied. At once it could be programmed up to 4
descriptors due to hardware limitations.
The issue was found under stress test, so it might not bother ordinary users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to dmaengine kerneldoc the struct dma_chan has always a non-NULL
pointer to DMA device and a test in dma_async_device_register()
validates that DMA device must also point to struct device.
All pr_ prints except one in dma_channel_table_init() have valid DMA
channel or DMA device pointer available which allow convert them to use
dev_ functions and thus able to show the associated DMA device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are only three patches this time, most other changes to
files in include/asm-generic tend to go through the tree of whoever
depends on the change.
Two patches are cleanups for stuff that is no longer needed,
the main change is to adapt the generic version of BUG_ON()
for CONFIG_BUG=n to make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings
about that undefined behavior in randconfig builds when
we keep going on after hitting a BUG_ON().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8tPL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP, uniphier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAVu68DGCrR//JCVInAQIHVQ//Wblms+NKj3aKh6m2Sscs/YkSbFaQ4sY2
rNyfxLIYsLXkth1kbdHRFSMyL68Ym+xutErgw/3HQPB2D1YtYJE3VJ/y8AU92SU3
oHyQIty+atB8d8zBbtlkWmat94NIfYf0I8PQETreGb1LMaJqAf0mDEDAyorTLZcZ
UtQ817Ihn7urqwdTJpTO58V41RmY/vflbHI5T6bIjUJn6fF1e/7+VqtMIfq5sjJ6
0EPEQdu8s5AJ7gcGlGi9I5gAtSnWSA/9phAxul9P8/HrMpUWIxreSEAy8FY7W14F
4TON3sQrnw7nyA72U80KGIXhgLy7SbEmHcSqyy4YJK3ycdk6VYk0CBO7nWVYAiD1
knLisOH6jwe0LIj9WXiRR+Y2Q53pXN8SF77pLDahSnvuShnYEjEH5uELHtxe7Vxh
gn+NH1rDkRTgdYgt4RWlVyUoLkddQWzLb1m4QyQlvxtTR25cJJayXdVX2MRrNPF5
c1zRa9HH+b8LJQIMdWfo/NoHhHtftkkGGsqHAAaypZqdpyk0j2HpJYk5ecPR4f5C
/8o/h/5xOI9gEzp/DVYSZ1VAvRqBQGIDfKBXWq6GuoZaF0aN8ISe5IxFn5Yx2F46
fNaxqiNpWmyywl8D+tSWPFK6aE21AXKGi5zIzexZZqy283aDjlUPI+tgF2GKIuKP
3ayYTDeBpLI=
=ynNj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
This is smallish update with minor changes to core and new driver and usual
updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the mapping.
- We now expose the maxburst for slave dma as new capability so clients can
know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in progress
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wCCJ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is smallish update with minor changes to core and new driver and
usual updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the
mapping.
- We now expose the maxburst for slave dma as new capability so
clients can know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in
progress"
* tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
dmaengine: IOATDMA: revise channel reset workaround on CB3.3 platforms
dmaengine: add Qualcomm Technologies HIDMA channel driver
dmaengine: add Qualcomm Technologies HIDMA management driver
dmaengine: hidma: Add Device Tree binding
dmaengine: qcom_bam_dma: move to qcom directory
dmaengine: tegra: Move of_device_id table near to its user
dmaengine: xilinx_vdma: Remove unnecessary variable initializations
dmaengine: sirf: use __maybe_unused to hide pm functions
dmaengine: rcar-dmac: clear pertinence number of channels
dmaengine: sh: shdmac: don't open code of_device_get_match_data()
dmaengine: tegra: don't open code of_device_get_match_data()
dmaengine: qcom_bam_dma: Make driver work for BE
dmaengine: sun4i: support module autoloading
dma/mic_x100_dma: IS_ERR() vs PTR_ERR() typo
dmaengine: xilinx_vdma: Use readl_poll_timeout instead of do while loop's
dmaengine: xilinx_vdma: Simplify spin lock handling
dmaengine: xilinx_vdma: Fix issues with non-parking mode
dmaengine: xilinx_vdma: Improve SG engine handling
dmaengine: pl330: fix to support the burst mode
dmaengine: make slave address physical
...
Pull dma_*_writecombine rename from Ingo Molnar:
"Rename dma_*_writecombine() to dma_*_wc()
This is a tree-wide API rename, to move the dma_*() write-combining
APIs closer in name to their usual API families. (The old API names
are kept as compatibility wrappers to not introduce extra breakage.)
The patch was Coccinelle generated"
* 'mm-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma, mm/pat: Rename dma_*_writecombine() to dma_*_wc()