Introduced in commit 38b5beeae7 ("net: dsa: sja1105: prepare tagger
for handling DSA tags and VLAN simultaneously"), the sja1105_xmit_tpid
function solved quite a different problem than our needs are now.
Then, we used best-effort VLAN filtering and we were using the xmit_tpid
to tunnel packets coming from an 8021q upper through the TX VLAN allocated
by tag_8021q to that egress port. The need for a different VLAN protocol
depending on switch revision came from the fact that this in itself was
more of a hack to trick the hardware into accepting tunneled VLANs in
the first place.
Right now, we deny 8021q uppers (see sja1105_prechangeupper). Even if we
supported them again, we would not do that using the same method of
{tunneling the VLAN on egress, retagging the VLAN on ingress} that we
had in the best-effort VLAN filtering mode. It seems rather simpler that
we just allocate a VLAN in the VLAN table that is simply not used by the
bridge at all, or by any other port.
Anyway, I have 2 gripes with the current sja1105_xmit_tpid:
1. When sending packets on behalf of a VLAN-aware bridge (with the new
TX forwarding offload framework) plus untagged (with the tag_8021q
VLAN added by the tagger) packets, we can see that on SJA1105P/Q/R/S
and later (which have a qinq_tpid of ETH_P_8021AD), some packets sent
through the DSA master have a VLAN protocol of 0x8100 and others of
0x88a8. This is strange and there is no reason for it now. If we have
a bridge and are therefore forced to send using that bridge's TPID,
we can as well blend with that bridge's VLAN protocol for all packets.
2. The sja1105_xmit_tpid introduces a dependency on the sja1105 driver,
because it looks inside dp->priv. It is desirable to keep as much
separation between taggers and switch drivers as possible. Now it
doesn't do that anymore.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver is a bit special in its use of VLAN headers as DSA
tags. This is because in VLAN-aware mode, the VLAN headers use an actual
TPID of 0x8100, which is understood even by the DSA master as an actual
VLAN header.
Furthermore, control packets such as PTP and STP are transmitted with no
VLAN header as a DSA tag, because, depending on switch generation, there
are ways to steer these control packets towards a precise egress port
other than VLAN tags. Transmitting control packets as untagged means
leaving a door open for traffic in general to be transmitted as untagged
from the DSA master, and for it to traverse the switch and exit a random
switch port according to the FDB lookup.
This behavior is a bit out of line with other DSA drivers which have
native support for DSA tagging. There, it is to be expected that the
switch only accepts DSA-tagged packets on its CPU port, dropping
everything that does not match this pattern.
We perhaps rely a bit too much on the switches' hardware dropping on the
CPU port, and place no other restrictions in the kernel data path to
avoid that. For example, sja1105 is also a bit special in that STP/PTP
packets are transmitted using "management routes"
(sja1105_port_deferred_xmit): when sending a link-local packet from the
CPU, we must first write a SPI message to the switch to tell it to
expect a packet towards multicast MAC DA 01-80-c2-00-00-0e, and to route
it towards port 3 when it gets it. This entry expires as soon as it
matches a packet received by the switch, and it needs to be reinstalled
for the next packet etc. All in all quite a ghetto mechanism, but it is
all that the sja1105 switches offer for injecting a control packet.
The driver takes a mutex for serializing control packets and making the
pairs of SPI writes of a management route and its associated skb atomic,
but to be honest, a mutex is only relevant as long as all parties agree
to take it. With the DSA design, it is possible to open an AF_PACKET
socket on the DSA master net device, and blast packets towards
01-80-c2-00-00-0e, and whatever locking the DSA switch driver might use,
it all goes kaput because management routes installed by the driver will
match skbs sent by the DSA master, and not skbs generated by the driver
itself. So they will end up being routed on the wrong port.
So through the lens of that, maybe it would make sense to avoid that
from happening by doing something in the network stack, like: introduce
a new bit in struct sk_buff, like xmit_from_dsa. Then, somewhere around
dev_hard_start_xmit(), introduce the following check:
if (netdev_uses_dsa(dev) && !skb->xmit_from_dsa)
kfree_skb(skb);
Ok, maybe that is a bit drastic, but that would at least prevent a bunch
of problems. For example, right now, even though the majority of DSA
switches drop packets without DSA tags sent by the DSA master (and
therefore the majority of garbage that user space daemons like avahi and
udhcpcd and friends create), it is still conceivable that an aggressive
user space program can open an AF_PACKET socket and inject a spoofed DSA
tag directly on the DSA master. We have no protection against that; the
packet will be understood by the switch and be routed wherever user
space says. Furthermore: there are some DSA switches where we even have
register access over Ethernet, using DSA tags. So even user space
drivers are possible in this way. This is a huge hole.
However, the biggest thing that bothers me is that udhcpcd attempts to
ask for an IP address on all interfaces by default, and with sja1105, it
will attempt to get a valid IP address on both the DSA master as well as
on sja1105 switch ports themselves. So with IP addresses in the same
subnet on multiple interfaces, the routing table will be messed up and
the system will be unusable for traffic until it is configured manually
to not ask for an IP address on the DSA master itself.
It turns out that it is possible to avoid that in the sja1105 driver, at
least very superficially, by requesting the switch to drop VLAN-untagged
packets on the CPU port. With the exception of control packets, all
traffic originated from tag_sja1105.c is already VLAN-tagged, so only
STP and PTP packets need to be converted. For that, we need to uphold
the equivalence between an untagged and a pvid-tagged packet, and to
remember that the CPU port of sja1105 uses a pvid of 4095.
Now that we drop untagged traffic on the CPU port, non-aggressive user
space applications like udhcpcd stop bothering us, and sja1105 effectively
becomes just as vulnerable to the aggressive kind of user space programs
as other DSA switches are (ok, users can also create 8021q uppers on top
of the DSA master in the case of sja1105, but in future patches we can
easily deny that, but it still doesn't change the fact that VLAN-tagged
packets can still be injected over raw sockets).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the mibs for MP_FAIL: MPTCP_MIB_MPFAILTX and
MPTCP_MIB_MPFAILRX.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bad checksum is detected, set the send_mp_fail flag to send out
the MP_FAIL option.
Add a new function mptcp_has_another_subflow() to check whether there's
only a single subflow.
When multiple subflows are in use, close the affected subflow with a RST
that includes an MP_FAIL option and discard the data with the bad
checksum.
Set the sk_state of the subsocket to TCP_CLOSE, then the flag
MPTCP_WORK_CLOSE_SUBFLOW will be set in subflow_sched_work_if_closed,
and the subflow will be closed.
When a single subfow is in use, temporarily handled by sending MP_FAIL
with a RST too.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added handling for receiving MP_FAIL suboption.
Add a new members mp_fail and fail_seq in struct mptcp_options_received.
When MP_FAIL suboption is received, set mp_fail to 1 and save the sequence
number to fail_seq.
Then invoke mptcp_pm_mp_fail_received to deal with the MP_FAIL suboption.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the MP_FAIL suboption sending support.
Add a new flag named send_mp_fail in struct mptcp_subflow_context. If
this flag is set, send out MP_FAIL suboption.
Add a new member fail_seq in struct mptcp_out_options to save the data
sequence number to put into the MP_FAIL suboption.
An MP_FAIL option could be included in a RST or on the subflow-level
ACK.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have several protocol constraints on MPTCP options
generation (e.g. MPC and MPJ subopt are mutually exclusive)
and some additional ones required by our implementation
(e.g. almost all ADD_ADDR variant are mutually exclusive with
everything else).
We can leverage the above to optimize the out option generation:
we check DSS/MPC/MPJ presence in a mutually exclusive way,
avoiding many unneeded conditionals in the common cases.
Additionally extend the existing constraints on ADD_ADDR opt on
all subvariants, so that it becomes fully mutually exclusive with
the above and we can skip another conditional statement for the
common case.
This change is also needed by the next patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The source of most of the slow down is the `dev_addr_lists.c` module,
which mainatins a linked list of HW addresses.
When using IPv6, this list grows for each IPv6 address added on a
VLAN, since each IPv6 address has a multicast HW address associated with
it.
When performing any modification to the involved links, this list is
traversed many times, often for nothing, all while holding the RTNL
lock.
Instead, this patch adds an auxilliary rbtree which cuts down
traversal time significantly.
Performance can be seen with the following script:
#!/bin/bash
ip netns del test || true 2>/dev/null
ip netns add test
echo 1 | ip netns exec test tee /proc/sys/net/ipv6/conf/all/keep_addr_on_down > /dev/null
set -e
ip -n test link add foo type veth peer name bar
ip -n test link add b1 type bond
ip -n test link add florp type vrf table 10
ip -n test link set bar master b1
ip -n test link set foo up
ip -n test link set bar up
ip -n test link set b1 up
ip -n test link set florp up
VLAN_COUNT=1500
BASE_DEV=b1
echo Creating vlans
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test link add link $BASE_DEV name foo.\$i type vlan id \$i; done"
echo Bringing them up
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test link set foo.\$i up; done"
echo Assiging IPv6 Addresses
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test address add dev foo.\$i 2000::\$i/64; done"
echo Attaching to VRF
ip netns exec test time -p bash -c "for i in \$(seq 1 $VLAN_COUNT);
do ip -n test link set foo.\$i master florp; done"
On an Intel(R) Xeon(R) CPU E5-2650 v3 @ 2.30GHz machine, the performance
before the patch is (truncated):
Creating vlans
real 108.35
Bringing them up
real 4.96
Assiging IPv6 Addresses
real 19.22
Attaching to VRF
real 458.84
After the patch:
Creating vlans
real 5.59
Bringing them up
real 5.07
Assiging IPv6 Addresses
real 5.64
Attaching to VRF
real 25.37
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Lu Wei <luwei32@huawei.com>
Cc: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Gilad Naaman <gnaaman@drivenets.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_handle_ingress_vlan_tunnel() is only referenced in
br_handle_frame(). If br_handle_ingress_vlan_tunnel() is called and
return non-zero value, goto drop in br_handle_frame().
But, br_handle_ingress_vlan_tunnel() always return 0. So, the
routines that check the return value and goto drop has no meaning.
Therefore, change return type of br_handle_ingress_vlan_tunnel() to
void and remove if statement of br_handle_frame().
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210823102118.17966-1-l4stpr0gr4m@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, there are many drivers who support CQE mode configuration,
some configure it as a fixed when initialized, some provide an
interface to change it by ethtool private flags. In order to make it
more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and
'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these
parameters can be accessed by ethtool netlink coalesce uAPI.
Also add an new structure kernel_ethtool_coalesce, then the
new parameter can be added into this struct.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no need to synchronize the account updating, so
use the relaxed atomic to avoid some memory barrier in the
data path.
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit e358bef7c3 ("net: dsa: Give drivers the chance
to veto certain upper devices"), the hellcreek driver uses some tricks
to comply with the network stack expectations: it enforces port
separation in standalone mode using VLANs. For untagged traffic,
bridging between ports is prevented by using different PVIDs, and for
VLAN-tagged traffic, it never accepts 8021q uppers with the same VID on
two ports, so packets with one VLAN cannot leak from one port to another.
That is almost fine*, and has worked because hellcreek relied on an
implicit behavior of the DSA core that was changed by the previous
patch: the standalone ports declare the 'rx-vlan-filter' feature as 'on
[fixed]'. Since most of the DSA drivers are actually VLAN-unaware in
standalone mode, that feature was actually incorrectly reflecting the
hardware/driver state, so there was a desire to fix it. This leaves the
hellcreek driver in a situation where it has to explicitly request this
behavior from the DSA framework.
We configure the ports as follows:
- Standalone: 'rx-vlan-filter' is on. An 8021q upper on top of a
standalone hellcreek port will go through dsa_slave_vlan_rx_add_vid
and will add a VLAN to the hardware tables, giving the driver the
opportunity to refuse it through .port_prechangeupper.
- Bridged with vlan_filtering=0: 'rx-vlan-filter' is off. An 8021q upper
on top of a bridged hellcreek port will not go through
dsa_slave_vlan_rx_add_vid, because there will not be any attempt to
offload this VLAN. The driver already disables VLAN awareness, so that
upper should receive the traffic it needs.
- Bridged with vlan_filtering=1: 'rx-vlan-filter' is on. An 8021q upper
on top of a bridged hellcreek port will call dsa_slave_vlan_rx_add_vid,
and can again be vetoed through .port_prechangeupper.
*It is not actually completely fine, because if I follow through
correctly, we can have the following situation:
ip link add br0 type bridge vlan_filtering 0
ip link set lan0 master br0 # lan0 now becomes VLAN-unaware
ip link set lan0 nomaster # lan0 fails to become VLAN-aware again, therefore breaking isolation
This patch fixes that corner case by extending the DSA core logic, based
on this requested attribute, to change the VLAN awareness state of the
switch (port) when it leaves the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been multiple independent reports about
dsa_slave_vlan_rx_add_vid being called (and consequently calling the
drivers' .port_vlan_add) when it isn't needed, and sometimes (not
always) causing problems in the process.
Case 1:
mv88e6xxx_port_vlan_prepare is stubborn and only accepts VLANs on
bridged ports. That is understandably so, because standalone mv88e6xxx
ports are VLAN-unaware, and VTU entries are said to be a scarce
resource.
Otherwise said, the following fails lamentably on mv88e6xxx:
ip link add br0 type bridge vlan_filtering 1
ip link set lan3 master br0
ip link add link lan10 name lan10.1 type vlan id 1
[485256.724147] mv88e6085 d0032004.mdio-mii:12: p10: hw VLAN 1 already used by port 3 in br0
RTNETLINK answers: Operation not supported
This has become a worse issue since commit 9b236d2a69 ("net: dsa:
Advertise the VLAN offload netdev ability only if switch supports it").
Up to that point, the driver was returning -EOPNOTSUPP and DSA was
reconverting that error to 0, making the 8021q upper think all is ok
(but obviously the error message was there even prior to this change).
After that change the -EOPNOTSUPP is propagated to vlan_vid_add, and it
is a hard error.
Case 2:
Ports that don't offload the Linux bridge (have a dp->bridge_dev = NULL
because they don't implement .port_bridge_{join,leave}). Understandably,
a standalone port should not offload VLANs either, it should remain VLAN
unaware and any VLAN should be a software VLAN (as long as the hardware
is not quirky, that is).
In fact, dsa_slave_port_obj_add does do the right thing and rejects
switchdev VLAN objects coming from the bridge when that bridge is not
offloaded:
case SWITCHDEV_OBJ_ID_PORT_VLAN:
if (!dsa_port_offloads_bridge_port(dp, obj->orig_dev))
return -EOPNOTSUPP;
err = dsa_slave_vlan_add(dev, obj, extack);
But it seems that the bridge is able to trick us. The __vlan_vid_add
from br_vlan.c has:
/* Try switchdev op first. In case it is not supported, fallback to
* 8021q add.
*/
err = br_switchdev_port_vlan_add(dev, v->vid, flags, extack);
if (err == -EOPNOTSUPP)
return vlan_vid_add(dev, br->vlan_proto, v->vid);
So it says "no, no, you need this VLAN in your life!". And we, naive as
we are, say "oh, this comes from the vlan_vid_add code path, it must be
an 8021q upper, sure, I'll take that". And we end up with that bridge
VLAN installed on our port anyway. But this time, it has the wrong flags:
if the bridge was trying to install VLAN 1 as a pvid/untagged VLAN,
failed via switchdev, retried via vlan_vid_add, we have this comment:
/* This API only allows programming tagged, non-PVID VIDs */
So what we do makes absolutely no sense.
Backtracing a bit, we see the common pattern. We allow the network stack
to think that our standalone ports are VLAN-aware, but they aren't, for
the vast majority of switches. The quirky ones should not dictate the
norm. The dsa_slave_vlan_rx_add_vid and dsa_slave_vlan_rx_kill_vid
methods exist for drivers that need the 'rx-vlan-filter: on' feature in
ethtool -k, which can be due to any of the following reasons:
1. vlan_filtering_is_global = true, and some ports are under a
VLAN-aware bridge while others are standalone, and the standalone
ports would otherwise drop VLAN-tagged traffic. This is described in
commit 061f6a505a ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid
implementation").
2. the ports that are under a VLAN-aware bridge should also set this
feature, for 8021q uppers having a VID not claimed by the bridge.
In this case, the driver will essentially not even know that the VID
is coming from the 8021q layer and not the bridge.
3. Hellcreek. This driver needs it because in standalone mode, it uses
unique VLANs per port to ensure separation. For separation of untagged
traffic, it uses different PVIDs for each port, and for separation of
VLAN-tagged traffic, it never accepts 8021q uppers with the same vid
on two ports.
If a driver does not fall under any of the above 3 categories, there is
no reason why it should advertise the 'rx-vlan-filter' feature, therefore
no reason why it should offload the VLANs added through vlan_vid_add.
This commit fixes the problem by removing the 'rx-vlan-filter' feature
from the slave devices when they operate in standalone mode, and when
they offload a VLAN-unaware bridge.
The way it works is that vlan_vid_add will now stop its processing here:
vlan_add_rx_filter_info:
if (!vlan_hw_filter_capable(dev, proto))
return 0;
So the VLAN will still be saved in the interface's VLAN RX filtering
list, but because it does not declare VLAN filtering in its features,
the 8021q module will return zero without committing that VLAN to
hardware.
This gives the drivers what they want, since it keeps the 8021q VLANs
away from the VLAN table until VLAN awareness is enabled (point at which
the ports are no longer standalone, hence in the mv88e6xxx case, the
check in mv88e6xxx_port_vlan_prepare passes).
Since the issue predates the existence of the hellcreek driver, case 3
will be dealt with in a separate patch.
The main change that this patch makes is to no longer set
NETIF_F_HW_VLAN_CTAG_FILTER unconditionally, but toggle it dynamically
(for most switches, never).
The second part of the patch addresses an issue that the first part
introduces: because the 'rx-vlan-filter' feature is now dynamically
toggled, and our .ndo_vlan_rx_add_vid does not get called when
'rx-vlan-filter' is off, we need to avoid bugs such as the following by
replaying the VLANs from 8021q uppers every time we enable VLAN
filtering:
ip link add link lan0 name lan0.100 type vlan id 100
ip addr add 192.168.100.1/24 dev lan0.100
ping 192.168.100.2 # should work
ip link add br0 type bridge vlan_filtering 0
ip link set lan0 master br0
ping 192.168.100.2 # should still work
ip link set br0 type bridge vlan_filtering 1
ping 192.168.100.2 # should still work but doesn't
As reported by Florian, some drivers look at ds->vlan_filtering in
their .port_vlan_add() implementation. So this patch also makes sure
that ds->vlan_filtering is committed before calling the driver. This is
the reason why it is first committed, then restored on the failure path.
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver does not implement .port_bridge_{join,leave}, then we must
fall back to standalone operation on that port, and trigger the error
path of dsa_port_bridge_join. This sets dp->bridge_dev = NULL.
In turn, having a non-NULL dp->bridge_dev when there is no offloading
support makes the following things go wrong:
- dsa_default_offload_fwd_mark make the wrong decision in setting
skb->offload_fwd_mark. It should set skb->offload_fwd_mark = 0 for
ports that don't offload the bridge, which should instruct the bridge
to forward in software. But this does not happen, dp->bridge_dev is
incorrectly set to point to the bridge, so the bridge is told that
packets have been forwarded in hardware, which they haven't.
- switchdev objects (MDBs, VLANs) should not be offloaded by ports that
don't offload the bridge. Standalone ports should behave as packet-in,
packet-out and the bridge should not be able to manipulate the pvid of
the port, or tag stripping on egress, or ingress filtering. This
should already work fine because dsa_slave_port_obj_add has:
case SWITCHDEV_OBJ_ID_PORT_VLAN:
if (!dsa_port_offloads_bridge_port(dp, obj->orig_dev))
return -EOPNOTSUPP;
err = dsa_slave_vlan_add(dev, obj, extack);
but since dsa_port_offloads_bridge_port works based on dp->bridge_dev,
this is again sabotaging us.
All the above work in case the port has an unoffloaded LAG interface, so
this is well exercised code, we should apply it for plain unoffloaded
bridge ports too.
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ports that have a NULL dp->bridge_dev, dsa_port_to_bridge_port()
also returns NULL as expected.
Issue #1 is that we are performing a NULL pointer dereference on brport_dev.
Issue #2 is that these are ports on which switchdev_bridge_port_offload
has not been called, so we should not call switchdev_bridge_port_unoffload
on them either.
Both issues are addressed by checking against a NULL brport_dev in
dsa_port_pre_bridge_leave and exiting early.
Fixes: 2f5dc00f7a ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPTCP_ADD_ADDR_IPV6 and MPTCP_ADD_ADDR_PORT are not necessary, we can get
these info from pm.local or pm.remote.
Drop mptcp_pm_should_add_signal_ipv6 and mptcp_pm_should_add_signal_port
too.
Co-developed-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Yonglong Li <liyonglong@chinatelecom.cn>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the MPTCP_ADD_ADDR_SIGNAL or MPTCP_ADD_ADDR_ECHO flag, build
the ADD_ADDR/ADD_ADDR_ECHO option.
In mptcp_pm_add_addr_signal(), use opts->addr to save the announced
ADD_ADDR or ADD_ADDR_ECHO address.
Co-developed-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Yonglong Li <liyonglong@chinatelecom.cn>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ADD_ADDR shares pm.addr_signal with RM_ADDR, so after RM_ADDR/ADD_ADDR
has done, we should not clean ADD_ADDR/RM_ADDR's addr_signal.
Co-developed-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Yonglong Li <liyonglong@chinatelecom.cn>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MPTCP_ADD_ADDR_SIGNAL only for the action of sending ADD_ADDR, and
use MPTCP_ADD_ADDR_ECHO only for the action of sending ADD_ADDR echo.
Use msk->pm.local to save the announced ADD_ADDR address only, and reuse
msk->pm.remote to save the announced ADD_ADDR_ECHO address.
To prepare for the next patch.
Co-developed-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Yonglong Li <liyonglong@chinatelecom.cn>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moved the drop_other_suboptions check from
mptcp_established_options_add_addr() into mptcp_pm_add_addr_signal(), do
it under the PM lock to avoid the race between this check and
mptcp_pm_add_addr_signal().
For this, added a new parameter for mptcp_pm_add_addr_signal() to get
the drop_other_suboptions value. And drop the other suboptions after the
option length check if drop_other_suboptions is true.
Additionally, always drop the other suboption for TCP pure ack:
that makes both the code simpler and the MPTCP behaviour more
consistent.
Co-developed-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Yonglong Li <liyonglong@chinatelecom.cn>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip_options_fragment() only called when iter->offset is equal to zero,
so move it out of loop, and inline 'Copy the flags to each fragment.'
As also, remove the unused parameter in ip_frag_ipcb().
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, cross-tree bridging setups work somewhat by mistake.
In the case of cross-tree bridging with sja1105, all switch instances
need to agree upon a common VLAN ID for forwarding a packet that belongs
to a certain bridging domain.
With TX forwarding offload, the VLAN ID is the bridge VLAN for
VLAN-aware bridging, and the tag_8021q TX forwarding offload VID
(a VLAN which has non-zero VBID bits) for VLAN-unaware bridging.
The VBID for VLAN-unaware bridging is derived from the dp->bridge_num
value calculated by DSA independently for each switch tree.
If ports from one tree join one bridge, and ports from another tree join
another bridge, DSA will assign them the same bridge_num, even though
the bridges are different. If cross-tree bridging is supported, this
is an issue.
Modify DSA to calculate the bridge_num globally across all switch trees.
This has the implication for a driver that the dp->bridge_num value that
DSA will assign to its ports might not be contiguous, if there are
boards with multiple DSA drivers instantiated. Additionally, all
bridge_num values eat up towards each switch's
ds->num_fwd_offloading_bridges maximum, which is potentially unfortunate,
and can be seen as a limitation introduced by this patch. However, that
is the lesser evil for now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* BSS coloring support
* MEI commands for Intel platforms
* various fixes/cleanups
-----BEGIN PGP SIGNATURE-----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=q8bL
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-08-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Minor updates:
* BSS coloring support
* MEI commands for Intel platforms
* various fixes/cleanups
* tag 'mac80211-next-for-net-next-2021-08-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
cfg80211: fix BSS color notify trace enum confusion
mac80211: Fix insufficient headroom issue for AMSDU
mac80211: add support for BSS color change
nl80211: add support for BSS coloring
mac80211: Use flex-array for radiotap header bitmap
mac80211: radiotap: Use BIT() instead of shifts
mac80211: Remove unnecessary variable and label
mac80211: include <linux/rbtree.h>
mac80211: Fix monitor MTU limit so that A-MSDUs get through
mac80211: remove unnecessary NULL check in ieee80211_register_hw()
mac80211: Reject zero MAC address in sta_info_insert_check()
nl80211: vendor-cmd: add Intel vendor commands for iwlmei usage
====================
Link: https://lore.kernel.org/r/20210820105329.48674-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The per-vlan router option controls the port/vlan and host vlan entries'
mcast router config. The global option controlled only the host vlan
config, but that is unnecessary and incosistent as it's not really a
global vlan option, but rather bridge option to control host router
config, so convert BRIDGE_VLANDB_GOPTS_MCAST_ROUTER to
BRIDGE_VLANDB_ENTRY_MCAST_ROUTER which can be used to control both host
vlan and port vlan mcast router config.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change br_multicast_set_port_router to take port multicast context as
its first argument so we can later use it to control port/vlan mcast
router option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE7E6oRXp8w05ovYr/9JCA4xAyCykFAmEe1xEZHGx1aXoudm9u
LmRlbnR6QGludGVsLmNvbQAKCRD0kIDjEDILKX/YEACMlYxmWJn2birrH5h4c+FA
6hzoDw+Kp+/Qo0FYPgWw6ady+cKuh50itKz8W050JR+n9eVdRehZ3Rlr/Yv2ol51
TSTjRKPbeDmtkGzC9h+dVBgkEERF88mF8FZiFXp+9vG/dfS4Lq2WdWzEFuYmfZyD
ZMuI9PsepmprORVI37B1WjZfdUo2XeA9ZKHUVSesgarNg55mZ4T/WEFnEc8KH2rX
HiqAeX+H2lt38ZEru7l5Jp6mNnzJJKLcnFjWMHXia865B8dHqC++goMXdJ8Tqcm8
NLs2W1RZgZocVwovwQ17bTiu41VnN7LdVpCig5RGcn1YtQUPcYzqBI971ixQCJUN
7vjqyMV3i+nLLD3FZmD+qYMYH/M2LaLH6fbaN0KBDlElCDHT7/Qu9N2nGreyiqKc
uuEXVHbGou3sj/LkBpNKJOGtmNkUo0XN93/giu89ZHGc7BLN1tUJM9NYWaiO1TcD
YiD0LO/lqmggCs9SQH0DBTUDNZ1vUDOzmVeD/tu/NqnixzSMseyqeThshZhxz6UT
7fBXvwixl+AhrN2lIxmS4WAtEwOPvaayUW8af7kESlrC4RoFvq+QaghT1D4NDpcq
llYlg/gt97Wy3AnIsnvEjd0s+lxGN6byIOBgTfC4jAfPAYA4oxd7N+1vMPFyChUV
MwatwE+IE1u2hjQWhMhVuA==
=INb2
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- update docs about move IRC channel away from freenode,
by Sven Eckelmann
- Switch to kstrtox.h for kstrtou64, by Sven Eckelmann
- Update NULL checks, by Sven Eckelmann (2 patches)
- remove remaining skb-copy calls for broadcast packets,
by Linus Lüssing
-----BEGIN PGP SIGNATURE-----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=sHz+
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-pullrequest-20210819' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- update docs about move IRC channel away from freenode,
by Sven Eckelmann
- Switch to kstrtox.h for kstrtou64, by Sven Eckelmann
- Update NULL checks, by Sven Eckelmann (2 patches)
- remove remaining skb-copy calls for broadcast packets,
by Linus Lüssing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hci_error_reset() return without calling hci_dev_do_open() when
hci_dev_do_close() return error value which is not 0.
Also, hci_dev_close() return hci_dev_do_close() function's return
value.
But, hci_dev_do_close() return always 0 even if hdev->shutdown
return error value. So, fix hci_dev_do_close() to save and return
the return value of the hdev->shutdown when it is called.
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot hit "task hung" bug in hci_req_sync(). The problem was in
unreasonable huge inquiry timeout passed from userspace.
Fix it by adding sanity check for timeout value to hci_inquiry().
Since hci_inquiry() is the only user of hci_req_sync() with user
controlled timeout value, it makes sense to check timeout value in
hci_inquiry() and don't touch hci_req_sync().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+be2baed593ea56c6a84c@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After gaining __alloc_size hints, GCC thinks it can reach a memcpy()
with eir_len == 0 (since it can't see into the rewrite of status).
Instead, check eir_len == 0, avoiding this future warning:
In function 'eir_append_data',
inlined from 'read_local_oob_ext_data_complete' at net/bluetooth/mgmt.c:7210:12:
./include/linux/fortify-string.h:54:29: warning: '__builtin_memcpy' offset 5 is out of the bounds [0, 3] [-Warray-bounds]
...
net/bluetooth/hci_request.h:133:2: note: in expansion of macro 'memcpy'
133 | memcpy(&eir[eir_len], data, data_len);
| ^~~~~~
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu field is not used. Remove it.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If directly after an MP_CAPABLE 3WHS, the client receives an ADD_ADDR
with HMAC from the server, it is enough to switch to a "fully
established" mode because it has received more MPTCP options.
It was then OK to enable the "fully_established" flag on the MPTCP
socket. Still, best to check if the ADD_ADDR looks valid by looking if
it contains an HMAC (no 'echo' bit). If an ADD_ADDR echo is received
while we are not in "fully established" mode, it is strange and then
we should not switch to this mode now.
But that is not enough. On one hand, the path-manager has be notified
the state has changed. On the other hand, the "fully_established" flag
on the subflow socket should be turned on as well not to re-send the
MP_CAPABLE 3rd ACK content with the next ACK.
Fixes: 84dfe3677a ("mptcp: send out dedicated ADD_ADDR packet")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Simply put: Linux 5.11 and later.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/60efc69f-1f35-529d-a7ef-da0549cad143@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We currently have two code paths for broadcast packets:
A) self-generated, via batadv_interface_tx()->
batadv_send_bcast_packet().
B) received/forwarded, via batadv_recv_bcast_packet()->
batadv_forw_bcast_packet().
For A), self-generated broadcast packets:
The only modifications to the skb data is the ethernet header which is
added/pushed to the skb in
batadv_send_broadcast_skb()->batadv_send_skb_packet(). However before
doing so, batadv_skb_head_push() is called which calls skb_cow_head() to
unshare the space for the to be pushed ethernet header. So for this
case, it is safe to use skb clones.
For B), received/forwarded packets:
The same applies as in A) for the to be forwarded packets. Only the
ethernet header is added. However after (queueing for) forwarding the
packet in batadv_recv_bcast_packet()->batadv_forw_bcast_packet(), a
packet is additionally decapsulated and is sent up the stack through
batadv_recv_bcast_packet()->batadv_interface_rx().
Protocols higher up the stack are already required to check if the
packet is shared and create a copy for further modifications. When the
next (protocol) layer works correctly, it cannot happen that it tries to
operate on the data behind the skb clone which is still queued up for
forwarding.
Co-authored-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Currently, the declaration of fill_imix_distribution() is dependent
on CONFIG_XFRM. This is incorrect.
Move fill_imix_distribution() declaration out of #ifndef CONFIG_XFRM
block.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add gfp_t mask as an input parameter to mem_cgroup_charge_skmem(),
to give more control to the networking stack and enable it to change
memcg charging behavior. In the future, the networking stack may decide
to avoid oom-kills when fallbacks are more appropriate.
One behavior change in mem_cgroup_charge_skmem() by this patch is to
avoid force charging by default and let the caller decide when and if
force charging is needed through the presence or absence of
__GFP_NOFAIL.
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only one caller for ops_free(), so inline it.
Separate net_drop_ns() and net_free(), so the net_free()
can be called directly.
Add free_exit_list() helper function for free net_exit_list.
====================
v2:
- v1 does not apply, rebase it.
====================
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tag_sja1105 running on non-sja1105 DSA ports, by making
sure that every time we dereference dp->priv, we check the switch's
dsa_switch_ops (otherwise we access a struct sja1105_port structure that
is in fact something else).
This adds an unconditional build-time dependency between sja1105 being
built as module => tag_sja1105 must also be built as module. This was
there only for PTP before.
Some sane defaults must also take place when not running on sja1105
hardware. These are:
- sja1105_xmit_tpid: the sja1105 driver uses different VLAN protocols
depending on VLAN awareness and switch revision (when an encapsulated
VLAN must be sent). Default to 0x8100.
- sja1105_rcv_meta_state_machine: this aggregates PTP frames with their
metadata timestamp frames. When running on non-sja1105 hardware, don't
do that and accept all frames unmodified.
- sja1105_defer_xmit: calls sja1105_port_deferred_xmit in sja1105_main.c
which writes a management route over SPI. When not running on sja1105
hardware, bypass the SPI write and send the frame as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed608 ("sch_cake: Take advantage of skb->hash where appropriate")
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add seq_puts() statement for dev_mcast, make it more readable.
As also, keep vertical alignment for {dev, ptype, dev_mcast} that
under /proc/net.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all dependent RxRPC kconfig entries be dependent on AF_RXRPC
so that they are presented (indented) after AF_RXRPC instead
of being presented at the same level on indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In mptcp_pm_nl_add_addr_received(), fill a temporary allocate array of
all local address corresponding to the fullmesh endpoint. If such array
is empty, keep the current behavior.
Elsewhere loop on such array and create a subflow for each local address
towards the given remote address
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added and managed a new per endpoint flag, named
MPTCP_PM_ADDR_FLAG_FULLMESH.
In mptcp_pm_create_subflow_or_signal_addr(), if such flag is set, instead
of:
remote_address((struct sock_common *)sk, &remote);
fill a temporary allocated array of all known remote address. After
releaseing the pm lock loop on such array and create a subflow for each
remote address from the given local.
Note that the we could still use an array even for non 'fullmesh'
endpoint: with a single entry corresponding to the primary MPC subflow
remote address.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added a new helper mptcp_pm_get_flags_and_ifindex_by_id(),
and used it in __mptcp_subflow_connect() to get the flags and ifindex
values.
Then the two arguments flags and ifindex of __mptcp_subflow_connect()
can be dropped.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong enum was used here, leading to warnings.
Just use a u32 instead.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 0d2ab3aea5 ("nl80211: add support for BSS coloring")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
