In commit b49a087("block: remove split code in
blkdev_issue_{discard,write_same}"), discard_granularity and alignment
checks were removed. Ideally, with bio late splitting, the upper layers
shouldn't need to depend on device's limits.
Christoph reported a discard regression on the HGST Ultrastar SN100 NVMe
device when mkfs.xfs. We have not found the root cause yet.
This patch re-adds discard_granularity and alignment checks by reverting
the related changes in commit b49a087. The good thing is now we can
remove the 2G discard size cap and just use UINT_MAX to avoid bi_size
overflow.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The stat files on the root cgroup shows stats for the whole system and
usually don't contain any information which isn't available through
the usual system monitoring mechanisms. Some controllers skip
collecting these duplicate stats to optimize cases where cgroup isn't
used and later try to emulate the result on demand.
This leads to complexities and subtle differences in the information
shown through different channels. This is entirely unnecessary and
cgroup v2 is dropping stat files which are duplicate from all
controllers. This patch removes "io.stat" from the root hierarchy.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Vivek Goyal <vgoyal@redhat.com>
Most of times, flush plug should be the hottest I/O path,
so mark ctx as pending after all requests in the list are
inserted.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The trace point is for tracing plug event of each request
queue instead of each task, so we should check the request
count in the plug list from current queue instead of
current task.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After bio splitting is introduced, one bio can be splitted
and it is marked as NOMERGE because it is too fat to be merged,
so check bio_mergeable() earlier to avoid to try to merge it
unnecessarily.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It isn't necessary to try to merge the bio which is marked
as NOMERGE.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The splitted bio has been already too fat to merge, so mark it
as NOMERGE.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The number of bio->bi_phys_segments is always obtained
during bio splitting, so it is natural to setup it
just after bio splitting, then we can avoid to compute
nr_segment again during merge.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Request queues with merging disabled will not flush the plug list after
BLK_MAX_REQUEST_COUNT requests have been queued, since the code relies
on blk_attempt_plug_merge to compute the request_count. Fix this by
computing the number of queued requests even for nomerge queues.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This commits adds a driver API and ioctls for controlling Persistent
Reservations s/genericly/generically/ at the block layer. Persistent
Reservations are supported by SCSI and NVMe and allow controlling who gets
access to a device in a shared storage setup.
Note that we add a pr_ops structure to struct block_device_operations
instead of adding the members directly to avoid bloating all instances
of devices that will never support Persistent Reservations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Split out helpers for all non-trivial ioctls to make this function simpler,
and also start passing around a pointer version of the argument, as that's
what most ioctl handlers actually need.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The libnvidmm-btt and nvme drivers use blk_integrity to reserve space
for per-sector metadata, but sometimes without protection checksums.
This property is generically useful, so teach the block core to
internally specify a nop profile if one is not provided at registration
time.
Cc: Keith Busch <keith.busch@intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
[hch: kill the local nvme nop profile as well]
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since they lack requests to pin the request_queue active, synchronous
bio-based drivers may have in-flight integrity work from
bio_integrity_endio() that is not flushed by blk_freeze_queue(). Flush
that work to prevent races to free the queue and the final usage of the
blk_integrity profile.
This is temporary unless/until bio-based drivers start to generically
take a q_usage_counter reference while a bio is in-flight.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
[martin: fix the CONFIG_BLK_DEV_INTEGRITY=n case]
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A trace like the following proceeds a crash in bio_integrity_process()
when it goes to use an already freed blk_integrity profile.
BUG: unable to handle kernel paging request at ffff8800d31b10d8
IP: [<ffff8800d31b10d8>] 0xffff8800d31b10d8
PGD 2f65067 PUD 21fffd067 PMD 80000000d30001e3
Oops: 0011 [#1] SMP
Dumping ftrace buffer:
---------------------------------
ndctl-2222 2.... 44526245us : disk_release: pmem1s
systemd--2223 4.... 44573945us : bio_integrity_endio: pmem1s
<...>-409 4.... 44574005us : bio_integrity_process: pmem1s
---------------------------------
[..]
Call Trace:
[<ffffffff8144e0f9>] ? bio_integrity_process+0x159/0x2d0
[<ffffffff8144e4f6>] bio_integrity_verify_fn+0x36/0x60
[<ffffffff810bd2dc>] process_one_work+0x1cc/0x4e0
Given that a request_queue is pinned while i/o is in flight and that a
gendisk is allowed to have a shorter lifetime, move blk_integrity to
request_queue to satisfy requests arriving after the gendisk has been
torn down.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
[martin: fix the CONFIG_BLK_DEV_INTEGRITY=n case]
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow pmem, and other synchronous/bio-based block drivers, to fallback
on a per-cpu reference count managed by the core for tracking queue
live/dead state.
The existing per-cpu reference count for the blk_mq case is promoted to
be used in all block i/o scenarios. This involves initializing it by
default, waiting for it to drop to zero at exit, and holding a live
reference over the invocation of q->make_request_fn() in
generic_make_request(). The blk_mq code continues to take its own
reference per blk_mq request and retains the ability to freeze the
queue, but the check that the queue is frozen is moved to
generic_make_request().
This fixes crash signatures like the following:
BUG: unable to handle kernel paging request at ffff880140000000
[..]
Call Trace:
[<ffffffff8145e8bf>] ? copy_user_handle_tail+0x5f/0x70
[<ffffffffa004e1e0>] pmem_do_bvec.isra.11+0x70/0xf0 [nd_pmem]
[<ffffffffa004e331>] pmem_make_request+0xd1/0x200 [nd_pmem]
[<ffffffff811c3162>] ? mempool_alloc+0x72/0x1a0
[<ffffffff8141f8b6>] generic_make_request+0xd6/0x110
[<ffffffff8141f966>] submit_bio+0x76/0x170
[<ffffffff81286dff>] submit_bh_wbc+0x12f/0x160
[<ffffffff81286e62>] submit_bh+0x12/0x20
[<ffffffff813395bd>] jbd2_write_superblock+0x8d/0x170
[<ffffffff8133974d>] jbd2_mark_journal_empty+0x5d/0x90
[<ffffffff813399cb>] jbd2_journal_destroy+0x24b/0x270
[<ffffffff810bc4ca>] ? put_pwq_unlocked+0x2a/0x30
[<ffffffff810bc6f5>] ? destroy_workqueue+0x225/0x250
[<ffffffff81303494>] ext4_put_super+0x64/0x360
[<ffffffff8124ab1a>] generic_shutdown_super+0x6a/0xf0
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Up until now the_integrity profile has been dynamically allocated and
attached to struct gendisk after the disk has been made active.
This causes problems because NVMe devices need to register the profile
prior to the partition table being read due to a mandatory metadata
buffer requirement. In addition, DM goes through hoops to deal with
preallocating, but not initializing integrity profiles.
Since the integrity profile is small (4 bytes + a pointer), Christoph
suggested moving it to struct gendisk proper. This requires several
changes:
- Moving the blk_integrity definition to genhd.h.
- Inlining blk_integrity in struct gendisk.
- Removing the dynamic allocation code.
- Adding helper functions which allow gendisk to set up and tear down
the integrity sysfs dir when a disk is added/deleted.
- Adding a blk_integrity_revalidate() callback for updating the stable
pages bdi setting.
- The calls that depend on whether a device has an integrity profile or
not now key off of the bi->profile pointer.
- Simplifying the integrity support routines in DM (Mike Snitzer).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The size of the data interval was not exported in the sysfs integrity
directory. Export it so that userland apps can tell whether the interval
is different from the device's logical block size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The per-device properties in the blk_integrity structure were previously
unsigned short. However, most of the values fit inside a char. The only
exception is the data interval size and we can work around that by
storing it as a power of two.
This cuts the size of the dynamic portion of blk_integrity in half.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We previously made a complete copy of a device's data integrity profile
even though several of the fields inside the blk_integrity struct are
pointers to fixed template entries in t10-pi.c.
Split the static and per-device portions so that we can reference the
template directly.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The integrity kobject purely exists to support the integrity
subdirectory in sysfs and doesn't really have anything to do with the
blk_integrity data structure. Move the kobject to struct gendisk where
it belongs.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
bdi's are initialized in two steps, bdi_init() and bdi_register(), but
destroyed in a single step by bdi_destroy() which, for a bdi embedded
in a request_queue, is called during blk_cleanup_queue() which makes
the queue invisible and starts the draining of remaining usages.
A request_queue's user can access the congestion state of the embedded
bdi as long as it holds a reference to the queue. As such, it may
access the congested state of a queue which finished
blk_cleanup_queue() but hasn't reached blk_release_queue() yet.
Because the congested state was embedded in backing_dev_info which in
turn is embedded in request_queue, accessing the congested state after
bdi_destroy() was called was fine. The bdi was destroyed but the
memory region for the congested state remained accessible till the
queue got released.
a13f35e871 ("writeback: don't embed root bdi_writeback_congested in
bdi_writeback") changed the situation. Now, the root congested state
which is expected to be pinned while request_queue remains accessible
is separately reference counted and the base ref is put during
bdi_destroy(). This means that the root congested state may go away
prematurely while the queue is between bdi_dstroy() and
blk_cleanup_queue(), which was detected by Andrey's KASAN tests.
The root cause of this problem is that bdi doesn't distinguish the two
steps of destruction, unregistration and release, and now the root
congested state actually requires a separate release step. To fix the
issue, this patch separates out bdi_unregister() and bdi_exit() from
bdi_destroy(). bdi_unregister() is called from blk_cleanup_queue()
and bdi_exit() from blk_release_queue(). bdi_destroy() is now just a
simple wrapper calling the two steps back-to-back.
While at it, the prototype of bdi_destroy() is moved right below
bdi_setup_and_register() so that the counterpart operations are
located together.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: a13f35e871 ("writeback: don't embed root bdi_writeback_congested in bdi_writeback")
Cc: stable@vger.kernel.org # v4.2+
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
Link: http://lkml.kernel.org/g/CAAeHK+zUJ74Zn17=rOyxacHU18SgCfC6bsYW=6kCY5GXJBwGfQ@mail.gmail.com
Reviewed-by: Jan Kara <jack@suse.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
tags is freed in blk_mq_free_rq_map() and should not be used after that.
The problem doesn't manifest if CONFIG_CPUMASK_OFFSTACK is false because
free_cpumask_var() is nop.
tags->cpumask is allocated in blk_mq_init_tags() so it's natural to
free cpumask in its counter part, blk_mq_free_tags().
Fixes: f26cdc8536 ("blk-mq: Shared tag enhancements")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_tag_update_depth() seems to be missing a memory barrier which
might cause the waker to not notice the waiter and fail to send a
wake_up as in the following figure.
blk_mq_tag_update_depth bt_get
------------------------------------------------------------------------
if (waitqueue_active(&bs->wait))
/* The CPU might reorder the test for
the waitqueue up here, before
prior writes complete */
prepare_to_wait(&bs->wait, &wait,
TASK_UNINTERRUPTIBLE);
tag = __bt_get(hctx, bt, last_tag,
tags);
/* Value set in bt_update_count not
visible yet */
bt_update_count(&tags->bitmap_tags, tdepth);
/* blk_mq_tag_wakeup_all(tags, false); */
bt = &tags->bitmap_tags;
wake_index = atomic_read(&bt->wake_index);
...
io_schedule();
------------------------------------------------------------------------
This patch adds the missing memory barrier.
I found this issue when I was looking through the linux source code
for places calling waitqueue_active() before wake_up*(), but without
preceding memory barriers, after sending a patch to fix a similar
issue in drivers/tty/n_tty.c (Details about the original issue can be
found here: https://lkml.org/lkml/2015/9/28/849).
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWEUxnAAoJEHm+PkMAQRiGYCYH/3gtGkFdvSLi+E1PfI8Qk3ZA
XuYA4Mj09JBVSmaICeueMTDVrdiq0OE0zPib26GWlF/za13kNU8KgMR3+6XCuLSX
DiCmh6mwDItoNoSIIUERLqrFHABXz8rZ3gb3uu2+kNN74Cl0piNm1YpFclEEWjMr
9Wk5fkq+ontnDVUQOvWUxPiUXOJTvdLXBWTRDw1yTdE3RMNwRI2d/hme6Hq++WYV
tRalZZKQaoB33js9WRVAoLVunvtna+i+/y7VGLj8QyS0+d6ec81Hey2r1/fR/oG4
bs4ul6vtqeb3IR/PjUqxF59pSrCLEO+qrp9KrTlJNYgr1m1QyjRxWUdy/XhyaWo=
=gIhN
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc4' into for-4.4/core
Linux 4.3-rc4
Pulling in v4.3-rc4 to avoid conflicts with NVMe fixes that have gone
in since for-4.4/core was based.
And replace the blk_mq_tag_busy_iter with it - the driver use has been
replaced with a new helper a while ago, and internal to the block we
only need the new version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_complete_request may be a no-op if the request has already
been completed by others means (e.g. a timeout or cancellation), but
currently drivers have to set rq->errors before calling
blk_mq_complete_request, which might leave us with the wrong error value.
Add an error parameter to blk_mq_complete_request so that we can
defer setting rq->errors until we known we won the race to complete the
request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
CPU hotplug handling for blk-mq (blk_mq_queue_reinit) acquires
all_q_mutex in blk_mq_queue_reinit_notify() and then removes sysfs
entries by blk_mq_sysfs_unregister(). Removing sysfs entry needs to
be blocked until the active reference of the kernfs_node to be zero.
On the other hand, reading blk_mq_hw_sysfs_cpu sysfs entry (e.g.
/sys/block/nullb0/mq/0/cpu_list) acquires all_q_mutex in
blk_mq_hw_sysfs_cpus_show().
If these happen at the same time, a deadlock can happen. Because one
can wait for the active reference to be zero with holding all_q_mutex,
and the other tries to acquire all_q_mutex with holding the active
reference.
The reason that all_q_mutex is acquired in blk_mq_hw_sysfs_cpus_show()
is to avoid reading an imcomplete hctx->cpumask. Since reading sysfs
entry for blk-mq needs to acquire q->sysfs_lock, we can avoid deadlock
and reading an imcomplete hctx->cpumask by protecting q->sysfs_lock
while hctx->cpumask is being updated.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Notifier callbacks for CPU_ONLINE action can be run on the other CPU
than the CPU which was just onlined. So it is possible for the
process running on the just onlined CPU to insert request and run
hw queue before establishing new mapping which is done by
blk_mq_queue_reinit_notify().
This can cause a problem when the CPU has just been onlined first time
since the request queue was initialized. At this time ctx->index_hw
for the CPU, which is the index in hctx->ctxs[] for this ctx, is still
zero before blk_mq_queue_reinit_notify() is called by notifier
callbacks for CPU_ONLINE action.
For example, there is a single hw queue (hctx) and two CPU queues
(ctx0 for CPU0, and ctx1 for CPU1). Now CPU1 is just onlined and
a request is inserted into ctx1->rq_list and set bit0 in pending
bitmap as ctx1->index_hw is still zero.
And then while running hw queue, flush_busy_ctxs() finds bit0 is set
in pending bitmap and tries to retrieve requests in
hctx->ctxs[0]->rq_list. But htx->ctxs[0] is a pointer to ctx0, so the
request in ctx1->rq_list is ignored.
Fix it by ensuring that new mapping is established before onlined cpu
starts running.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
CPU hotplug handling for blk-mq (blk_mq_queue_reinit) accesses
q->mq_usage_counter while freezing all request queues in all_q_list.
On the other hand, q->mq_usage_counter is deinitialized in
blk_mq_free_queue() before deleting the queue from all_q_list.
So if CPU hotplug event occurs in the window, percpu_ref_kill() is
called with q->mq_usage_counter which has already been marked dead,
and it triggers warning. Fix it by deleting the queue from all_q_list
earlier than destroying q->mq_usage_counter.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
CPU hotplug handling for blk-mq (blk_mq_queue_reinit) updates
q->mq_map by blk_mq_update_queue_map() for all request queues in
all_q_list. On the other hand, q->mq_map is released before deleting
the queue from all_q_list.
So if CPU hotplug event occurs in the window, invalid memory access
can happen. Fix it by releasing q->mq_map in blk_mq_release() to make
it happen latter than removal from all_q_list.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is a race between cpu hotplug handling and adding/deleting
gendisk for blk-mq, where both are trying to register and unregister
the same sysfs entries.
null_add_dev
--> blk_mq_init_queue
--> blk_mq_init_allocated_queue
--> add to 'all_q_list' (*)
--> add_disk
--> blk_register_queue
--> blk_mq_register_disk (++)
null_del_dev
--> del_gendisk
--> blk_unregister_queue
--> blk_mq_unregister_disk (--)
--> blk_cleanup_queue
--> blk_mq_free_queue
--> del from 'all_q_list' (*)
blk_mq_queue_reinit
--> blk_mq_sysfs_unregister (-)
--> blk_mq_sysfs_register (+)
While the request queue is added to 'all_q_list' (*),
blk_mq_queue_reinit() can be called for the queue anytime by CPU
hotplug callback. But blk_mq_sysfs_unregister (-) and
blk_mq_sysfs_register (+) in blk_mq_queue_reinit must not be called
before blk_mq_register_disk (++) and after blk_mq_unregister_disk (--)
is finished. Because '/sys/block/*/mq/' is not exists.
There has already been BLK_MQ_F_SYSFS_UP flag in hctx->flags which can
be used to track these sysfs stuff, but it is only fixing this issue
partially.
In order to fix it completely, we just need per-queue flag instead of
per-hctx flag with appropriate locking. So this introduces
q->mq_sysfs_init_done which is properly protected with all_q_mutex.
Also, we need to ensure that blk_mq_map_swqueue() is called with
all_q_mutex is held. Since hctx->nr_ctx is reset temporarily and
updated in blk_mq_map_swqueue(), so we should avoid
blk_mq_register_hctx() seeing the temporary hctx->nr_ctx value
in CPU hotplug handling or adding/deleting gendisk .
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When unmapped hw queue is remapped after CPU topology is changed,
hctx->tags->cpumask has to be set after hctx->tags is setup in
blk_mq_map_swqueue(), otherwise it causes null pointer dereference.
Fixes: f26cdc8536 ("blk-mq: Shared tag enhancements")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The pages allocated for struct request contain pointers to other slab
allocations (via ops->init_request). Since kmemleak does not track/scan
page allocations, the slab objects will be reported as leaks (false
positives). This patch adds kmemleak callbacks to allow tracking of such
pages.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Bart Van Assche<bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block updates from Jens Axboe:
"This is a bit bigger than it should be, but I could (did) not want to
send it off last week due to both wanting extra testing, and expecting
a fix for the bounce regression as well. In any case, this contains:
- Fix for the blk-merge.c compilation warning on gcc 5.x from me.
- A set of back/front SG gap merge fixes, from me and from Sagi.
This ensures that we honor SG gapping for integrity payloads as
well.
- Two small fixes for null_blk from Matias, fixing a leak and a
capacity propagation issue.
- A blkcg fix from Tejun, fixing a NULL dereference.
- A fast clone optimization from Ming, fixing a performance
regression since the arbitrarily sized bio's were introduced.
- Also from Ming, a regression fix for bouncing IOs"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix bounce_end_io
block: blk-merge: fast-clone bio when splitting rw bios
block: blkg_destroy_all() should clear q->root_blkg and ->root_rl.blkg
block: Copy a user iovec if it includes gaps
block: Refuse adding appending a gapped integrity page to a bio
block: Refuse request/bio merges with gaps in the integrity payload
block: Check for gaps on front and back merges
null_blk: fix wrong capacity when bs is not 512 bytes
null_blk: fix memory leak on cleanup
block: fix bogus compiler warnings in blk-merge.c
cgroup_on_dfl() tests whether the cgroup's root is the default
hierarchy; however, an individual controller is only interested in
whether the controller is attached to the default hierarchy and never
tests a cgroup which doesn't belong to the hierarchy that the
controller is attached to.
This patch replaces cgroup_on_dfl() tests in controllers with faster
static_key based cgroup_subsys_on_dfl(). This leaves cgroup core as
the only user of cgroup_on_dfl() and the function is moved from the
header file to cgroup.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Zefan Li <lizefan@huawei.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
When bio bounce is involved, one new bio and its biovecs are
cloned from the comming bio, which can be one fast-cloned bio
from upper layer(such as dm).
So it is obviously wrong to assume the start index of the coming(
original) bio's io vector is zero, which can be any value between
0 and (bi_max_vecs - 1), especially in case of bio split.
This patch fixes Fedora's booting oops on i386, often with the
following kernel log together:
> [ 9.026738] systemd[1]: Switching root.
> [ 9.036467] systemd-journald[149]: Received SIGTERM from PID 1
> (systemd).
> [ 9.082262] BUG: Bad page state in process kworker/u5:1 pfn:372ac
> [ 9.083989] page:f3d32ae0 count:0 mapcount:0 mapping:f2252178
> index:0x16a
> [ 9.085755] flags: 0x40020021(locked|lru|mappedtodisk)
> [ 9.087284] page dumped because: page still charged to cgroup
> [ 9.088772] bad because of flags:
> [ 9.089731] flags: 0x21(locked|lru)
> [ 9.090818] page->mem_cgroup:f2c3e400
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Tested-by: Adam Williamson <awilliam@redhat.com>
Cc: Ming Lin <mlin@kernel.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
biovecs has become immutable since v3.13, so it isn't necessary
to allocate biovecs for the new cloned bios, then we can save
one extra biovecs allocation/copy, and the allocation is often
not fixed-length and a bit more expensive.
For example, if the 'max_sectors_kb' of null blk's queue is set
as 16(32 sectors) via sysfs just for making more splits, this patch
can increase throught about ~70% in the sequential read test over
null_blk(direct io, bs: 1M).
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Ming Lin <ming.l@ssi.samsung.com>
Cc: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
This fixes a performance regression introduced by commit 54efd50bfd,
and allows us to take full advantage of the fact that we have immutable
bio_vecs. Hand applied, as it rejected violently with commit
5014c311ba.
Signed-off-by: Jens Axboe <axboe@fb.com>
While making the root blkg unconditional, ec13b1d6f0 ("blkcg: always
create the blkcg_gq for the root blkcg") removed the part which clears
q->root_blkg and ->root_rl.blkg during q exit. This leaves the two
pointers dangling after blkg_destroy_all(). blk-throttle exit path
performs blkg traversals and dereferences ->root_blkg and can lead to
the following oops.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000558
IP: [<ffffffff81389746>] __blkg_lookup+0x26/0x70
...
task: ffff88001b4e2580 ti: ffff88001ac0c000 task.ti: ffff88001ac0c000
RIP: 0010:[<ffffffff81389746>] [<ffffffff81389746>] __blkg_lookup+0x26/0x70
...
Call Trace:
[<ffffffff8138d14a>] blk_throtl_drain+0x5a/0x110
[<ffffffff8138a108>] blkcg_drain_queue+0x18/0x20
[<ffffffff81369a70>] __blk_drain_queue+0xc0/0x170
[<ffffffff8136a101>] blk_queue_bypass_start+0x61/0x80
[<ffffffff81388c59>] blkcg_deactivate_policy+0x39/0x100
[<ffffffff8138d328>] blk_throtl_exit+0x38/0x50
[<ffffffff8138a14e>] blkcg_exit_queue+0x3e/0x50
[<ffffffff8137016e>] blk_release_queue+0x1e/0xc0
...
While the bug is a straigh-forward use-after-free bug, it is tricky to
reproduce because blkg release is RCU protected and the rest of exit
path usually finishes before RCU grace period.
This patch fixes the bug by updating blkg_destro_all() to clear
q->root_blkg and ->root_rl.blkg.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Richard W.M. Jones" <rjones@redhat.com>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Link: http://lkml.kernel.org/g/CA+5PVA5rzQ0s4723n5rHBcxQa9t0cW8BPPBekr_9aMRoWt2aYg@mail.gmail.com
Fixes: ec13b1d6f0 ("blkcg: always create the blkcg_gq for the root blkcg")
Cc: stable@vger.kernel.org # v4.2+
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For drivers that don't support gaps in the SG lists handed to
them we must bounce (copy the user buffers) and pass a bio that
does not include gaps. This doesn't matter for any current user,
but will help to allow iser which can't handle gaps to use the
block virtual boundary instead of using driver-local bounce
buffering when handling SG_IO commands.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is only theoretical at the moment given that the only
subsystems that generate integrity payloads are the block layer
itself and the scsi target (which generate well aligned integrity
payloads). But when we will expose integrity meta-data to user-space,
we'll need to refuse appending a page with a gap (if the queue
virtual boundary is set).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a driver sets the block queue virtual boundary mask, it means that
it cannot handle gaps so we must not allow those in the integrity
payload as well.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Fixed up by me to have duplicate integrity merge functions, depending
on whether block integrity is enabled or not. Fixes a compilations
issue with CONFIG_BLK_DEV_INTEGRITY unset.
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull blk-cg updates from Jens Axboe:
"A bit later in the cycle, but this has been in the block tree for a a
while. This is basically four patchsets from Tejun, that improve our
buffered cgroup writeback. It was dependent on the other cgroup
changes, but they went in earlier in this cycle.
Series 1 is set of 5 patches that has cgroup writeback updates:
- bdi_writeback iteration fix which could lead to some wb's being
skipped or repeated during e.g. sync under memory pressure.
- Simplification of wb work wait mechanism.
- Writeback tracepoints updated to report cgroup.
Series 2 is is a set of updates for the CFQ cgroup writeback handling:
cfq has always charged all async IOs to the root cgroup. It didn't
have much choice as writeback didn't know about cgroups and there
was no way to tell who to blame for a given writeback IO.
writeback finally grew support for cgroups and now tags each
writeback IO with the appropriate cgroup to charge it against.
This patchset updates cfq so that it follows the blkcg each bio is
tagged with. Async cfq_queues are now shared across cfq_group,
which is per-cgroup, instead of per-request_queue cfq_data. This
makes all IOs follow the weight based IO resource distribution
implemented by cfq.
- Switched from GFP_ATOMIC to GFP_NOWAIT as suggested by Jeff.
- Other misc review points addressed, acks added and rebased.
Series 3 is the blkcg policy cleanup patches:
This patchset contains assorted cleanups for blkcg_policy methods
and blk[c]g_policy_data handling.
- alloc/free added for blkg_policy_data. exit dropped.
- alloc/free added for blkcg_policy_data.
- blk-throttle's async percpu allocation is replaced with direct
allocation.
- all methods now take blk[c]g_policy_data instead of blkcg_gq or
blkcg.
And finally, series 4 is a set of patches cleaning up the blkcg stats
handling:
blkcg's stats have always been somwhat of a mess. This patchset
tries to improve the situation a bit.
- The following patches added to consolidate blkcg entry point and
blkg creation. This is in itself is an improvement and helps
colllecting common stats on bio issue.
- per-blkg stats now accounted on bio issue rather than request
completion so that bio based and request based drivers can behave
the same way. The issue was spotted by Vivek.
- cfq-iosched implements custom recursive stats and blk-throttle
implements custom per-cpu stats. This patchset make blkcg core
support both by default.
- cfq-iosched and blk-throttle keep track of the same stats
multiple times. Unify them"
* 'for-4.3/blkcg' of git://git.kernel.dk/linux-block: (45 commits)
blkcg: use CGROUP_WEIGHT_* scale for io.weight on the unified hierarchy
blkcg: s/CFQ_WEIGHT_*/CFQ_WEIGHT_LEGACY_*/
blkcg: implement interface for the unified hierarchy
blkcg: misc preparations for unified hierarchy interface
blkcg: separate out tg_conf_updated() from tg_set_conf()
blkcg: move body parsing from blkg_conf_prep() to its callers
blkcg: mark existing cftypes as legacy
blkcg: rename subsystem name from blkio to io
blkcg: refine error codes returned during blkcg configuration
blkcg: remove unnecessary NULL checks from __cfqg_set_weight_device()
blkcg: reduce stack usage of blkg_rwstat_recursive_sum()
blkcg: remove cfqg_stats->sectors
blkcg: move io_service_bytes and io_serviced stats into blkcg_gq
blkcg: make blkg_[rw]stat_recursive_sum() to be able to index into blkcg_gq
blkcg: make blkcg_[rw]stat per-cpu
blkcg: add blkg_[rw]stat->aux_cnt and replace cfq_group->dead_stats with it
blkcg: consolidate blkg creation in blkcg_bio_issue_check()
blk-throttle: improve queue bypass handling
blkcg: move root blkg lookup optimization from throtl_lookup_tg() to __blkg_lookup()
blkcg: inline [__]blkg_lookup()
...
Pull ext3 removal, quota & udf fixes from Jan Kara:
"The biggest change in the pull is the removal of ext3 filesystem
driver (~28k lines removed). Ext4 driver is a full featured
replacement these days and both RH and SUSE use it for several years
without issues. Also there are some workarounds in VM & block layer
mainly for ext3 which we could eventually get rid of.
Other larger change is addition of proper error handling for
dquot_initialize(). The rest is small fixes and cleanups"
[ I wasn't convinced about the ext3 removal and worried about things
falling through the cracks for legacy users, but ext4 maintainers
piped up and were all unanimously in favor of removal, and maintaining
all legacy ext3 support inside ext4. - Linus ]
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Don't modify filesystem for read-only mounts
quota: remove an unneeded condition
ext4: memory leak on error in ext4_symlink()
mm/Kconfig: NEED_BOUNCE_POOL: clean-up condition
ext4: Improve ext4 Kconfig test
block: Remove forced page bouncing under IO
fs: Remove ext3 filesystem driver
doc: Update doc about journalling layer
jfs: Handle error from dquot_initialize()
reiserfs: Handle error from dquot_initialize()
ocfs2: Handle error from dquot_initialize()
ext4: Handle error from dquot_initialize()
ext2: Handle error from dquot_initalize()
quota: Propagate error from ->acquire_dquot()
We are checking for gaps to previous bio_vec, which can
only detect back merges gaps. Moreover, at the point where
we check for a gap, we don't know if we will attempt a back
or a front merge. Thus, check for gap to prev in a back merge
attempt and check for a gap to next in a front merge attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
[sagig: Minor rename change]
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
The compiler can't figure out that bvprv is initialized whenever 'prev'
is set to 1 as well. Use a pointer to bvprv instead, setting it to NULL
initially, and get rid of the 'prev' tracking. This dumbs it down
enough that gcc is happy.
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull SG updates from Jens Axboe:
"This contains a set of scatter-gather related changes/fixes for 4.3:
- Add support for limited chaining of sg tables even for
architectures that do not set ARCH_HAS_SG_CHAIN. From Christoph.
- Add sg chain support to target_rd. From Christoph.
- Fixup open coded sg->page_link in crypto/omap-sham. From
Christoph.
- Fixup open coded crypto ->page_link manipulation. From Dan.
- Also from Dan, automated fixup of manual sg_unmark_end()
manipulations.
- Also from Dan, automated fixup of open coded sg_phys()
implementations.
- From Robert Jarzmik, addition of an sg table splitting helper that
drivers can use"
* 'for-4.3/sg' of git://git.kernel.dk/linux-block:
lib: scatterlist: add sg splitting function
scatterlist: use sg_phys()
crypto/omap-sham: remove an open coded access to ->page_link
scatterlist: remove open coded sg_unmark_end instances
crypto: replace scatterwalk_sg_chain with sg_chain
target/rd: always chain S/G list
scatterlist: allow limited chaining without ARCH_HAS_SG_CHAIN
Pull core block updates from Jens Axboe:
"This first core part of the block IO changes contains:
- Cleanup of the bio IO error signaling from Christoph. We used to
rely on the uptodate bit and passing around of an error, now we
store the error in the bio itself.
- Improvement of the above from myself, by shrinking the bio size
down again to fit in two cachelines on x86-64.
- Revert of the max_hw_sectors cap removal from a revision again,
from Jeff Moyer. This caused performance regressions in various
tests. Reinstate the limit, bump it to a more reasonable size
instead.
- Make /sys/block/<dev>/queue/discard_max_bytes writeable, by me.
Most devices have huge trim limits, which can cause nasty latencies
when deleting files. Enable the admin to configure the size down.
We will look into having a more sane default instead of UINT_MAX
sectors.
- Improvement of the SGP gaps logic from Keith Busch.
- Enable the block core to handle arbitrarily sized bios, which
enables a nice simplification of bio_add_page() (which is an IO hot
path). From Kent.
- Improvements to the partition io stats accounting, making it
faster. From Ming Lei.
- Also from Ming Lei, a basic fixup for overflow of the sysfs pending
file in blk-mq, as well as a fix for a blk-mq timeout race
condition.
- Ming Lin has been carrying Kents above mentioned patches forward
for a while, and testing them. Ming also did a few fixes around
that.
- Sasha Levin found and fixed a use-after-free problem introduced by
the bio->bi_error changes from Christoph.
- Small blk cgroup cleanup from Viresh Kumar"
* 'for-4.3/core' of git://git.kernel.dk/linux-block: (26 commits)
blk: Fix bio_io_vec index when checking bvec gaps
block: Replace SG_GAPS with new queue limits mask
block: bump BLK_DEF_MAX_SECTORS to 2560
Revert "block: remove artifical max_hw_sectors cap"
blk-mq: fix race between timeout and freeing request
blk-mq: fix buffer overflow when reading sysfs file of 'pending'
Documentation: update notes in biovecs about arbitrarily sized bios
block: remove bio_get_nr_vecs()
fs: use helper bio_add_page() instead of open coding on bi_io_vec
block: kill merge_bvec_fn() completely
md/raid5: get rid of bio_fits_rdev()
md/raid5: split bio for chunk_aligned_read
block: remove split code in blkdev_issue_{discard,write_same}
btrfs: remove bio splitting and merge_bvec_fn() calls
bcache: remove driver private bio splitting code
block: simplify bio_add_page()
block: make generic_make_request handle arbitrarily sized bios
blk-cgroup: Drop unlikely before IS_ERR(_OR_NULL)
block: don't access bio->bi_error after bio_put()
block: shrink struct bio down to 2 cache lines again
...
The SG_GAPS queue flag caused checks for bio vector alignment against
PAGE_SIZE, but the device may have different constraints. This patch
adds a queue limits so a driver with such constraints can set to allow
requests that would have been unnecessarily split. The new gaps check
takes the request_queue as a parameter to simplify the logic around
invoking this function.
This new limit makes the queue flag redundant, so removing it and
all usage. Device-mappers will inherit the correct settings through
blk_stack_limits().
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup is trying to make interface consistent across different
controllers. For weight based resource control, the knob should have
the range [1, 10000] and default to 100. This patch updates
cfq-iosched so that the weight range conforms. The internal
calculations have enough range and the widening of the weight range
shouldn't cause any problem.
* blkcg_policy->cpd_bind_fn() is added. If present, this is invoked
when blkcg is attached to a hierarchy.
* cfq_cpd_init() is updated to use the new default value on the
unified hierarchy.
* cfq_cpd_bind() callback is implemented to clear per-blkg configs and
apply the default config matching the hierarchy type.
* cfqd->root_group->[leaf_]weight initialization in cfq_init_queue()
is moved into !CONFIG_CFQ_GROUP_IOSCHED block. cfq_cpd_bind() is
now responsible for initializing the initial weights when blkcg is
enabled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg is gonna switch to cgroup common weight range as defined by
CGROUP_WEIGHT_* on the unified hierarchy. In preparation, rename
CFQ_WEIGHT_* constants to CFQ_WEIGHT_LEGACY_*.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg interface grew to be the biggest of all controllers and
unfortunately most inconsistent too. The interface files are
inconsistent with a number of cloes duplicates. Some files have
recursive variants while others don't. There's distinction between
normal and leaf weights which isn't intuitive and there are a lot of
stat knobs which don't make much sense outside of debugging and expose
too much implementation details to userland.
In the unified hierarchy, everything is always hierarchical and
internal nodes can't have tasks rendering the two structural issues
twisting the current interface. The interface has to be updated in a
significant anyway and this is a good chance to revamp it as a whole.
This patch implements blkcg interface for the unified hierarchy.
* (from a previous patch) blkcg is identified by "io" instead of
"blkio" on the unified hierarchy. Given that the whole interface is
updated anyway, the rename shouldn't carry noticeable conversion
overhead.
* The original interface consisted of 27 files is replaced with the
following three files.
blkio.stat : per-blkcg stats
blkio.weight : per-cgroup and per-cgroup-queue weight settings
blkio.max : per-cgroup-queue bps and iops max limits
Documentation/cgroups/unified-hierarchy.txt updated accordingly.
v2: blkcg_policy->dfl_cftypes wasn't removed on
blkcg_policy_unregister() corrupting the cftypes list. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
tg_set_conf() is largely consisted of parsing and setting the new
config and the follow-up application and propagation. This patch
separates out the latter part into tg_conf_updated(). This will be
used to implement interface for the unified hierarchy.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, blkg_conf_prep() expects input to be of the following form
MAJ:MIN NUM
and reads the NUM part into blkg_conf_ctx->v. This is quite
restrictive and gets in the way in implementing blkcg interface for
the unified hierarchy. This patch updates blkg_conf_prep() so that it
expects
MAJ:MIN BODY_STR
where BODY_STR is an arbitrary string. blkg_conf_ctx->v is replaced
with ->body which is a char pointer pointing to the start of BODY_STR.
Parsing of the body is moved to blkg_conf_prep()'s callers.
To allow using, for example, strsep() on blkg_conf_ctx->val, it is a
non-const pointer and to accommodate that const is dropped from @input
too.
This doesn't cause any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkio interface has become messy over time and is currently the
largest. In addition to the inconsistent naming scheme, it has
multiple stat files which report more or less the same thing, a number
of debug stat files which expose internal details which shouldn't have
been part of the public interface in the first place, recursive and
non-recursive stats and leaf and non-leaf knobs.
Both recursive vs. non-recursive and leaf vs. non-leaf distinctions
don't make any sense on the unified hierarchy as only leaf cgroups can
contain processes. cgroups is going through a major interface
revision with the unified hierarchy involving significant fundamental
usage changes and given that a significant portion of the interface
doesn't make sense anymore, it's a good time to reorganize the
interface.
As the first step, this patch renames the external visible subsystem
name from "blkio" to "io". This is more concise, matches the other
two major subsystem names, "cpu" and "memory", and better suited as
blkcg will be involved in anything writeback related too whether an
actual block device is involved or not.
As the subsystem legacy_name is set to "blkio", the only userland
visible change outside the unified hierarchy is that blkcg is reported
as "io" instead of "blkio" in the subsystem initialized message during
boot. On the unified hierarchy, blkcg now appears as "io".
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: cgroups@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg currently returns -EINVAL for most errors which can be pretty
confusing given that the failure modes are quite varied. Update the
error returns so that
* -EINVAL only for syntactic errors.
* -ERANGE if the value is out of range.
* -ENODEV if the target device can't be found.
* -EOPNOTSUPP if the policy is not enabled on the target device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkg_to_cfqg() and blkcg_to_cfqgd() on a valid blkg with the policy
enabled are guaranteed to return non-NULL and the counterpart in
blk-throttle doesn't have these checks either. Remove the spurious
NULL checks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
The recent percpu conversion of blkg_rwstat triggered the following
warning in certain configurations.
block/blk-cgroup.c:654:1: warning: the frame size of 1360 bytes is larger than 1024 bytes
This is because blkg_rwstat now contains four percpu_counter which can
be pretty big depending on debug options although it shouldn't be a
problem in production configs. This patch removes one of the two
local blkg_rwstat variables used by blkg_rwstat_recursive_sum() to
reduce stack usage.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Link: http://article.gmane.org/gmane.linux.kernel.cgroups/13835
Signed-off-by: Jens Axboe <axboe@fb.com>
cfq_stats->sectors is a blkg_stat which keeps track of the total
number of sectors serviced; however, this can be trivially calculated
from blkcg_gq->stat_bytes. The only thing necessary is adding up
READs and WRITEs and then dividing by sector size.
Remove cfqg_stats->sectors and make cfq print "sectors" and
"sectors_recursive" from stat_bytes.
While this is a bit more code, it removes duplicate stat allocations
and updates and ensures that the reported stats stay in tune with each
other.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, both cfq-iosched and blk-throttle keep track of
io_service_bytes and io_serviced stats. While keeping track of them
separately may be useful during development, it doesn't make much
sense otherwise. Also, blk-throttle was counting bio's as IOs while
cfq-iosched request's, which is more confusing than informative.
This patch adds ->stat_bytes and ->stat_ios to blkg (blkcg_gq),
removes the counterparts from cfq-iosched and blk-throttle and let
them print from the common blkg counters. The common counters are
incremented during bio issue in blkcg_bio_issue_check().
The outputs are still filtered by whether the policy has
blkg_policy_data on a given blkg, so cfq's output won't show up if it
has never been used for a given blkg. The only times when the outputs
would differ significantly are when policies are attached on the fly
or elevators are switched back and forth. Those are quite exceptional
operations and I don't think they warrant keeping separate counters.
v3: Update blkio-controller.txt accordingly.
v2: Account IOs during bio issues instead of request completions so
that bio-based drivers can be handled the same way.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, blkg_[rw]stat_recursive_sum() assume that the target
counter is located in pd (blkg_policy_data); however, some counters
are planned to be moved to blkg (blkcg_gq).
This patch updates blkg_[rw]stat_recursive_sum() to take blkg and
blkg_policy pointers instead of pd. If policy is NULL, it indexes
into blkg. If non-NULL, into the blkg's pd of the policy.
The existing usages are updated to maintain the current behaviors.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg_[rw]stat are used as stat counters for blkcg policies. It isn't
per-cpu by itself and blk-throttle makes it per-cpu by wrapping around
it. This patch makes blkcg_[rw]stat per-cpu and drop the ad-hoc
per-cpu wrapping in blk-throttle.
* blkg_[rw]stat->cnt is replaced with cpu_cnt which is struct
percpu_counter. This makes syncp unnecessary as remote accesses are
handled by percpu_counter itself.
* blkg_[rw]stat_init() can now fail due to percpu allocation failure
and thus are updated to return int.
* percpu_counters need explicit freeing. blkg_[rw]stat_exit() added.
* As blkg_rwstat->cpu_cnt[] can't be read directly anymore, reading
and summing results are stored in ->aux_cnt[] instead.
* Custom per-cpu stat implementation in blk-throttle is removed.
This makes all blkcg stat counters per-cpu without complicating policy
implmentations.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup stats are local to each cgroup and doesn't propagate to
ancestors by default. When recursive stats are necessary, the sum is
calculated over all the descendants. This initially was for backward
compatibility to support both group-local and recursive stats but this
mode of operation makes general sense as stat update is much hotter
thafn reporting those stats.
This however ends up losing recursive stats when a child is removed.
To work around this, cfq-iosched adds its stats to its parent
cfq_group->dead_stats which is summed up together when calculating
recursive stats.
It's planned that the core stats will be moved to blkcg_gq, so we want
to move the mechanism for keeping track of the stats of dead children
from cfq to blkcg core. This patch adds blkg_[rw]stat->aux_cnt which
are atomic64_t's keeping track of auxiliary counts which are excluded
when reading local counts but included for recursive.
blkg_[rw]stat_merge() which were used by cfq to implement dead_stats
are replaced by blkg_[rw]stat_add_aux(), and cfq now forwards stats of
a dead cgroup to the aux counts of parent->stats instead of separate
->dead_stats.
This will also help making blkg_[rw]stats per-cpu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkg (blkcg_gq) currently is created by blkcg policies invoking
blkg_lookup_create() which ends up repeating about the same code in
different policies. Theoretically, this can avoid the overhead of
looking and/or creating blkg's if blkcg is enabled but no policy is in
use; however, the cost of blkg lookup / creation is very low
especially if only the root blkcg is in use which is highly likely if
no blkcg policy is in active use - it boils down to a single very
predictable conditional and surrounding RCU protection.
This patch consolidates blkg creation to a new function
blkcg_bio_issue_check() which is called during bio issue from
generic_make_request_checks(). blkcg_bio_issue_check() is now the
only function which tries to create missing blkg's. The subsequent
policy and request_list operations just perform blkg_lookup() and if
missing falls back to the root.
* blk_get_rl() no longer tries to create blkg. It uses blkg_lookup()
instead of blkg_lookup_create().
* blk_throtl_bio() is now called from blkcg_bio_issue_check() with rcu
read locked and blkg already looked up. Both throtl_lookup_tg() and
throtl_lookup_create_tg() are dropped.
* cfq is similarly updated. cfq_lookup_create_cfqg() is replaced with
cfq_lookup_cfqg()which uses blkg_lookup().
This consolidates blkg handling and avoids unnecessary blkg creation
retries under memory pressure. In addition, this provides a common
bio entry point into blkcg where things like common accounting can be
performed.
v2: Build fixes for !CONFIG_CFQ_GROUP_IOSCHED and
!CONFIG_BLK_DEV_THROTTLING.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a queue is bypassing, all blkcg policies should become noops but
blk-throttle wasn't. It only became noop if the queue was dying.
While this wouldn't lead to an oops as falling back to the root blkg
is safe in this case, this can be a bit surprising - a bypassing queue
could still be applying throttle limits.
Fix it by removing blk_queue_dying() test in throtl_lookup_create_tg()
and testing blk_queue_bypass() in blk_throtl_bio() and bypassing
before doing anything else.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, both throttle and cfq policies implement their own root
blkg (blkcg_gq) lookup fast path. This patch moves root blkg
optimization from throtl_lookup_tg() to __blkg_lookup(). cfq-iosched
currently doesn't use blkg_lookup() but will be converted and drop the
optimization too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkg_lookup() checks whether the target queue is bypassing and, if
not, calls __blkg_lookup() which first checks the lookup hint and then
performs radix tree walk. The operations upto hint checking are
trivial and there are many users of this function. This patch inlines
blkg_lookup() and the fast path part of __blkg_lookup(). The radix
tree lookup and hint update are now in blkg_lookup_slowpath().
This will help consolidating blkg handling by easing moving root blkcg
short-circuit to inlined lookup fast path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Each active policy has a cpd (blkcg_policy_data) on each blkcg. The
cpd's were allocated by blkcg core and each policy could request to
allocate extra space at the end by setting blkcg_policy->cpd_size
larger than the size of cpd.
This is a bit unusual but blkg (blkcg_gq) policy data used to be
handled this way too so it made sense to be consistent; however, blkg
policy data switched to alloc/free callbacks.
This patch makes similar changes to cpd handling.
blkcg_policy->cpd_alloc/free_fn() are added to replace ->cpd_size. As
cpd allocation is now done from policy side, it can simply allocate a
larger area which embeds cpd at the beginning.
As ->cpd_alloc_fn() may be able to perform all necessary
initializations, this patch makes ->cpd_init_fn() optional.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
* Rename blkcg->pd[] to blkcg->cpd[] so that cpd is consistently used
for blkcg_policy_data.
* Make blkcg_policy->cpd_init_fn() take blkcg_policy_data instead of
blkcg. This makes it consistent with blkg_policy_data methods and
to-be-added cpd alloc/free methods.
* blkcg_policy_data->blkcg and cpd_to_blkcg() added so that
cpd_init_fn() can determine the associated blkcg from
blkcg_policy_data.
v2: blkcg_policy_data->blkcg initializations were missing. Added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The newly added ->pd_alloc_fn() and ->pd_free_fn() deal with pd
(blkg_policy_data) while the older ones use blkg (blkcg_gq). As using
blkg doesn't make sense for ->pd_alloc_fn() and after allocation pd
can always be mapped to blkg and given that these are policy-specific
methods, it makes sense to converge on pd.
This patch makes all methods deal with pd instead of blkg. Most
conversions are trivial. In blk-cgroup.c, a couple method invocation
sites now test whether pd exists instead of policy state for
consistency. This shouldn't cause any behavioral differences.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
With the recent addition of alloc and free methods, things became
messier. This patch reorganizes them according to the followings.
* ->pd_alloc_fn()
Responsible for allocation and static initializations - the ones
which can be done independent of where the pd might be attached.
* ->pd_init_fn()
Initializations which require the knowledge of where the pd is
attached.
* ->pd_free_fn()
The counter part of pd_alloc_fn(). Static de-init and freeing.
This leaves ->pd_exit_fn() without any users. Removed.
While at it, collapse an one liner function throtl_pd_exit(), which
has only one user, into its user.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Because percpu allocator couldn't do non-blocking allocations,
blk-throttle was forced to implement an ad-hoc asynchronous allocation
mechanism for its percpu stats for cases where blkg's (blkcg_gq's) are
allocated from an IO path without sleepable context.
Now that percpu allocator can handle gfp_mask and blkg_policy_data
alloc / free are handled by policy methods, the ad-hoc asynchronous
allocation mechanism can be replaced with direct allocation from
tg_stats_alloc_fn(). Rit it out.
This ensures that an active throtl_grp always has valid non-NULL
->stats_cpu. Remove checks on it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A blkg (blkcg_gq) represents the relationship between a cgroup and
request_queue. Each active policy has a pd (blkg_policy_data) on each
blkg. The pd's were allocated by blkcg core and each policy could
request to allocate extra space at the end by setting
blkcg_policy->pd_size larger than the size of pd.
This is a bit unusual but was done this way mostly to simplify error
handling and all the existing use cases could be handled this way;
however, this is becoming too restrictive now that percpu memory can
be allocated without blocking.
This introduces two new mandatory blkcg_policy methods - pd_alloc_fn()
and pd_free_fn() - which are used to allocate and release pd for a
given policy. As pd allocation is now done from policy side, it can
simply allocate a larger area which embeds pd at the beginning. This
change makes ->pd_size pointless. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkg_create() allows NULL ->pd_init_fn() but blkcg_activate_policy()
doesn't. As both in-kernel policies implement ->pd_init_fn, it
currently doesn't break anything. Update blkcg_activate_policy() so
that its behavior is consistent with blkg_create().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a policy gets activated, it needs to allocate and install its
policy data on all existing blkg's (blkcg_gq's). Because blkg
iteration is protected by a spinlock, it currently counts the total
number of blkg's in the system, allocates the matching number of
policy data on a list and installs them during a single iteration.
This can be simplified by using speculative GFP_NOWAIT allocations
while iterating and falling back to a preallocated policy data on
failure. If the preallocated one has already been consumed, it
releases the lock, preallocate with GFP_KERNEL and then restarts the
iteration. This can be a bit more expensive than before but policy
activation is a very cold path and shouldn't matter.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg_css_alloc() bypasses policy data allocation and blkcg_css_free()
bypasses policy data and blkcg freeing for blkcg_root. There's no
reason to to treat policy data any differently for blkcg_root. If the
root css gets allocated after policies are registered, policy
registration path will add policy data; otherwise, the alloc path
will. The free path isn't never invoked for root csses.
This patch removes the unnecessary special handling of blkcg_root from
css_alloc/free paths.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When blkcg_init_queue() fails midway after creating a new blkg, it
performs kfree() directly; however, this doesn't free the policy data
areas. Make it use blkg_free() instead. In turn, blkg_free() is
updated to handle root request_list special case.
While this fixes a possible memory leak, it's on an unlikely failure
path of an already cold path and the size leaked per occurrence is
miniscule too. I don't think it needs to be tagged for -stable.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Up until now, all async IOs were queued to async queues which are
shared across the whole request_queue, which means that blkcg resource
control is completely void on async IOs including all writeback IOs.
It was done this way because writeback didn't support writeback and
there was no way of telling which writeback IO belonged to which
cgroup; however, writeback recently became cgroup aware and writeback
bio's are sent down properly tagged with the blkcg's to charge them
against.
This patch makes async cfq_queues per-cfq_cgroup instead of
per-cfq_data so that each async IO is charged to the blkcg that it was
tagged for instead of unconditionally attributing it to root.
* cfq_data->async_cfqq and ->async_idle_cfqq are moved to cfq_group
and alloc / destroy paths are updated accordingly.
* cfq_link_cfqq_cfqg() no longer overrides @cfqg to root for async
queues.
* check_blkcg_changed() now also invalidates async queues as they no
longer stay the same across cgroups.
After this patch, cfq's proportional IO control through blkio.weight
works correctly when cgroup writeback is in use.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cfq_find_alloc_queue() checks whether a queue actually needs to be
allocated, which is unnecessary as its sole caller, cfq_get_queue(),
only calls it if so. Also, the oom queue fallback logic is scattered
between cfq_get_queue() and cfq_find_alloc_queue(). There really
isn't much going on in the latter and things can be made simpler by
folding it into cfq_get_queue().
This patch collapses cfq_find_alloc_queue() into cfq_get_queue(). The
change is fairly straight-forward with one exception - async_cfqq is
now initialized to NULL and the "!is_sync" test in the last if
conditional is replaced with "async_cfqq" test. This is because gcc
(5.1.1) gets confused for some reason and warns that async_cfqq may be
used uninitialized otherwise. Oh well, the code isn't necessarily
worse this way.
This patch doesn't cause any functional difference.
v2: Updated to reflect GFP_ATOMIC -> GPF_NOWAIT.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is necessary for making async cfq_cgroups per-cfq_group instead
of per-cfq_data. While this change makes cfq_get_queue() perform RCU
locking and look up cfq_group even when it reuses async queue, the
extra overhead is extremely unlikely to be noticeable given that this
is already sitting behind cic->cfqq[] cache and the overall cost of
cfq operation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Even when allocations fail, cfq_find_alloc_queue() always returns a
valid cfq_queue by falling back to the oom cfq_queue. As such, there
isn't much point in taking @gfp_mask and trying "harder" if __GFP_WAIT
is set. GFP_NOWAIT allocations don't fail often and even when they do
the degraded behavior is acceptable and temporary.
After all, the only reason get_request(), which ultimately determines
the gfp_mask, cares about __GFP_WAIT is to guarantee request
allocation, assuming IO forward progress, for callers which are
willing to wait. There's no reason for cfq_find_alloc_queue() to
behave differently on __GFP_WAIT when it already has a fallback
mechanism.
Remove @gfp_mask from cfq_find_alloc_queue() and propagate the changes
to its callers. This simplifies the function quite a bit and will
help making async queues per-cfq_group.
v2: Updated to reflect GFP_ATOMIC -> GPF_NOWAIT.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg performs several allocations to track IOs per cgroup and enforce
resource control. Most of these allocations are performed lazily on
demand in the IO path and thus can't involve reclaim path. Currently,
these allocations use GFP_ATOMIC; however, blkcg can gracefully deal
with occassional failures of these allocations by punting IOs to the
root cgroup and there's no reason to reach into the emergency reserve.
This patch replaces GFP_ATOMIC with GFP_NOWAIT for the following
allocations.
* bdi_writeback_congested and blkcg_gq allocations in blkg_create().
* radix tree node allocations for blkcg->blkg_tree.
* cfq_queue allocation on ioprio changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-and-Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Suggested-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
* Some were accessing cic->cfqq[] directly. Always use cic_to_cfqq()
and cic_set_cfqq().
* check_ioprio_changed() doesn't need to verify cfq_get_queue()'s
return for NULL. It's always non-NULL. Simplify accordingly.
This patch doesn't cause any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the cfq_queue cached in cfq_io_cq is the oom one, cfq_set_request()
replaces it by invoking cfq_get_queue() again without putting the oom
queue leaking the reference it was holding. While oom queues are not
released through reference counting, they're still reference counted
and this can theoretically lead to the reference count overflowing and
incorrectly invoke the usual release path on it.
Fix it by making cfq_set_request() put the ref it was holding.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Async cfqq's (cfq_queue's) are shared across cfq_data. When
cfq_get_queue() obtains a new queue from cfq_find_alloc_queue(), it
stashes the pointer in cfq_data and reuses it from then on; however,
the function doesn't consider that cfq_find_alloc_queue() may return
the oom_cfqq under memory pressure and installs the returned queue
unconditionally.
If the oom_cfqq is installed as an async cfqq, cfq_set_request() will
continue calling cfq_get_queue() hoping to replace it with a proper
queue; however, cfq_get_queue() will keep returning the cached queue
for the slot - the oom_cfqq.
Fix it by skipping caching if the queue is the oom one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cfq_get_queue()'s control flow looks like the following.
async_cfqq = NULL;
cfqq = NULL;
if (!is_sync) {
...
async_cfqq = ...;
cfqq = *async_cfqq;
}
if (!cfqq)
cfqq = ...;
if (!is_sync && !(*async_cfqq))
...;
The only thing the local variable init, the second if, and the
async_cfqq test in the third if achieves is to skip cfqq creation and
installation if *async_cfqq was already non-NULL. This is needlessly
complicated with different tests examining the same condition.
Simplify it to the following.
if (!is_sync) {
...
async_cfqq = ...;
cfqq = *async_cfqq;
if (cfqq)
goto out;
}
cfqq = ...;
if (!is_sync)
...;
out:
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This reverts commit 34b48db66e.
That commit caused performance regressions for streaming I/O
workloads on a number of different storage devices, from
SATA disks to external RAID arrays. It also managed to
trip up some buggy firmware in at least one drive, causing
data corruption.
The next patch will bump the default max_sectors_kb value to
1280, which will accommodate a 10-data-disk stripe write
with chunk size 128k. In the testing I've done using iozone,
fio, and aio-stress, a value of 1280 does not show a big
performance difference from 512. This will hopefully still
help the software RAID setup that Christoph saw the original
performance gains with while still not regressing other
storage configurations.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[hch: split from a larger patch by Dan]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch consists of 2 libfc fixes causing rare crashes, one iscsi one
causing a potential hang on shutdown, an I/O blocksize issue which caused a
regression and a memory leak in scsi-mq.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJVzsOiAAoJEDeqqVYsXL0M4wQIAIUe1SGv66OcAQLBcxxJUL2T
i+Ph2RE/er1iyzJepN56i77Mn2hnBgnQtmB/ibnjQfUsz/zo5PANjIfy+eFcG53G
qcb8l7a/BFCH3JHWXL7rJYN9G64sirADDL6SDLpX1JFsL21bAGdcEgbmefysvDmr
qFkiGH0Ty9YH58W+6j1pzQhh437rRgcM1KuY08sJsbKmyCVdzG5ketzBkONmBcTh
OTfPQjL32L4KR3THDUbpCiK6YAUtDvHjVB51lwoiB1ER7Ke+E+nqlCuxhXvZfMoD
lGfvWgwaQnoN1fun6c85zcqnl72kymropWWiJUhhPPjeZEj8sgn/eaaAAST9mlQ=
=Fztd
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This has two libfc fixes for bugs causing rare crashes, one iscsi fix
for a potential hang on shutdown, and a fix for an I/O blocksize issue
which caused a regression"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Fix maximum I/O size for BLOCK_PC requests
libfc: Fix fc_fcp_cleanup_each_cmd()
libfc: Fix fc_exch_recv_req() error path
libiscsi: Fix host busy blocking during connection teardown
There may be lots of pending requests so that the buffer of PAGE_SIZE
can't hold them at all.
One typical example is scsi-mq, the queue depth(.can_queue) of
scsi_host and blk-mq is quite big but scsi_device's queue_depth
is a bit small(.cmd_per_lun), then it is quite easy to have lots
of pending requests in hw queue.
This patch fixes the following warning and the related memory
destruction.
[ 359.025101] fill_read_buffer: blk_mq_hw_sysfs_show+0x0/0x7d returned bad count^M
[ 359.055595] irq event stamp: 15537^M
[ 359.055606] general protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC ^M
[ 359.055614] Dumping ftrace buffer:^M
[ 359.055660] (ftrace buffer empty)^M
[ 359.055672] Modules linked in: nbd ipv6 kvm_intel kvm serio_raw^M
[ 359.055678] CPU: 4 PID: 21631 Comm: stress-ng-sysfs Not tainted 4.2.0-rc5-next-20150805 #434^M
[ 359.055679] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011^M
[ 359.055682] task: ffff8802161cc000 ti: ffff88021b4a8000 task.ti: ffff88021b4a8000^M
[ 359.055693] RIP: 0010:[<ffffffff811541c5>] [<ffffffff811541c5>] __kmalloc+0xe8/0x152^M
Cc: <stable@vger.kernel.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We can always fill up the bio now, no need to estimate the possible
size based on queue parameters.
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[hch: rebased and wrote a changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The split code in blkdev_issue_{discard,write_same} can go away
now that any driver that cares does the split. We have to make
sure bio size doesn't overflow.
For discard, we set max discard sectors to (1<<31)>>9 to ensure
it doesn't overflow bi_size and hopefully it is of the proper
granularity as long as the granularity is a power of two.
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since generic_make_request() can now handle arbitrary size bios, all we
have to do is make sure the bvec array doesn't overflow.
__bio_add_page() doesn't need to call ->merge_bvec_fn(), where
we can get rid of unnecessary code paths.
Removing the call to ->merge_bvec_fn() is also fine, as no driver that
implements support for BLOCK_PC commands even has a ->merge_bvec_fn()
method.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: rebase and resolve merge conflicts, change a couple of comments,
make bio_add_page() warn once upon a cloned bio.]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The way the block layer is currently written, it goes to great lengths
to avoid having to split bios; upper layer code (such as bio_add_page())
checks what the underlying device can handle and tries to always create
bios that don't need to be split.
But this approach becomes unwieldy and eventually breaks down with
stacked devices and devices with dynamic limits, and it adds a lot of
complexity. If the block layer could split bios as needed, we could
eliminate a lot of complexity elsewhere - particularly in stacked
drivers. Code that creates bios can then create whatever size bios are
convenient, and more importantly stacked drivers don't have to deal with
both their own bio size limitations and the limitations of the
(potentially multiple) devices underneath them. In the future this will
let us delete merge_bvec_fn and a bunch of other code.
We do this by adding calls to blk_queue_split() to the various
make_request functions that need it - a few can already handle arbitrary
size bios. Note that we add the call _after_ any call to
blk_queue_bounce(); this means that blk_queue_split() and
blk_recalc_rq_segments() don't need to be concerned with bouncing
affecting segment merging.
Some make_request_fn() callbacks were simple enough to audit and verify
they don't need blk_queue_split() calls. The skipped ones are:
* nfhd_make_request (arch/m68k/emu/nfblock.c)
* axon_ram_make_request (arch/powerpc/sysdev/axonram.c)
* simdisk_make_request (arch/xtensa/platforms/iss/simdisk.c)
* brd_make_request (ramdisk - drivers/block/brd.c)
* mtip_submit_request (drivers/block/mtip32xx/mtip32xx.c)
* loop_make_request
* null_queue_bio
* bcache's make_request fns
Some others are almost certainly safe to remove now, but will be left
for future patches.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Jim Paris <jim@jtan.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md/md.c' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: skip more mq-based drivers, resolve merge conflicts, etc.]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit bcdb247c6b ("sd: Limit transfer length") clamped the maximum
size of an I/O request to the MAXIMUM TRANSFER LENGTH field in the BLOCK
LIMITS VPD. This had the unfortunate effect of also limiting the maximum
size of non-filesystem requests sent to the device through sg/bsg.
Avoid using blk_queue_max_hw_sectors() and set the max_sectors queue
limit directly.
Also update the comment in blk_limits_max_hw_sectors() to clarify that
max_hw_sectors defines the limit for the I/O controller only.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Brian King <brking@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: James Bottomley <JBottomley@Odin.com>
