Commit 20167d3421 ("x86-64: Fix
accounting in kernel_physical_mapping_init()") went a little too
far by entirely removing the counting of pre-populated page
tables: this should be done at boot time (to cover the page
tables set up in early boot code), but shouldn't be done during
memory hot add.
Hence, re-add the removed increments of "pages", but make them
and the one in phys_pte_init() conditional upon !after_bootmem.
Reported-Acked-and-Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/506DAFBA020000780009FA8C@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Between 2.6.33 and 2.6.34 the PMU code was made modular.
The x86_pmu_enable() call was extended to disable cpuc->enabled
and iterate the counters, enabling one at a time, before calling
enable_all() at the end, followed by re-enabling cpuc->enabled.
Since cpuc->enabled was set to 0, that change effectively caused
the "val |= ARCH_PERFMON_EVENTSEL_ENABLE;" code in p6_pmu_enable_event()
and p6_pmu_disable_event() to be dead code that was never called.
This change removes this code (which was confusing) and adds some
extra commentary to make it more clear what is going on.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210191732000.14552@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch updates the generic events on p6, including some new
extended cache events.
Values for these events were taken from the equivelant PAPI
predefined events.
Tested on a Pentium II.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210191730080.14552@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
According to Intel SDM Volume 3B, FP_ASSIST is limited to Counter 1 only,
not Counter 0.
Tested on a Pentium II.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210191728570.14552@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
722bc6b167 x86/mm: Fix the size calculation of mapping tables
Tried to address the issue that the first 2/4M should use 4k pages
if PSE enabled, but extra counts should only be valid for x86_32.
This commit caused a kdump regression: the kdump kernel hangs.
Work is in progress to fundamentally fix the various page table
initialization issues that we have, via the design suggested
by H. Peter Anvin, but it's not ready yet to be merged.
So, to get a working kdump revert to the last known working version,
which is the revert of this commit and of a followup fix (which was
incomplete):
bd2753b2dd x86/mm: Only add extra pages count for the first memory range during pre-allocation
Tested kdump on physical and virtual machines.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Tested-by: Flavio Leitner <fbl@redhat.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Flavio Leitner <fbl@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: ianfang.cn@gmail.com
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In check_hw_exists() we try to detect non-emulated MSR accesses
by writing an arbitrary value into one of the PMU registers
and check if it's value after a readout is still the same.
This algorithm silently assumes that the register does not contain
the magic value already, which is wrong in at least one situation.
Fix the algorithm to really do a read-modify-write cycle. This fixes
a warning under Xen under some circumstances on AMD family 10h CPUs.
The reasons in more details actually sound like a story from
Believe It or Not!:
First you need an AMD family 10h/12h CPU. These do not reset the
PERF_CTR registers on a reboot.
Now you boot bare metal Linux, which goes successfully through this
check, but leaves the magic value of 0xabcd in the register. You
don't use the performance counters, but do a reboot (warm reset).
Then you choose to boot Xen. The check will be triggered with a
recent Linux kernel as Dom0 again, trying to write 0xabcd into the
MSR. Xen silently drops the write (expected), but the subsequent read
will return the value in the register, which just happens to be the
expected magic value. Thus the test misleadingly succeeds, leaving
the kernel in the belief that the PMU is available. This will trigger
the following message:
[ 0.020294] ------------[ cut here ]------------
[ 0.020311] WARNING: at arch/x86/xen/enlighten.c:730 xen_apic_write+0x15/0x17()
[ 0.020318] Hardware name: empty
[ 0.020323] Modules linked in:
[ 0.020334] Pid: 1, comm: swapper/0 Not tainted 3.3.8 #7
[ 0.020340] Call Trace:
[ 0.020354] [<ffffffff81050379>] warn_slowpath_common+0x80/0x98
[ 0.020369] [<ffffffff810503a6>] warn_slowpath_null+0x15/0x17
[ 0.020378] [<ffffffff810034df>] xen_apic_write+0x15/0x17
[ 0.020392] [<ffffffff8101cb2b>] perf_events_lapic_init+0x2e/0x30
[ 0.020410] [<ffffffff81ee4dd0>] init_hw_perf_events+0x250/0x407
[ 0.020419] [<ffffffff81ee4b80>] ? check_bugs+0x2d/0x2d
[ 0.020430] [<ffffffff81002181>] do_one_initcall+0x7a/0x131
[ 0.020444] [<ffffffff81edbbf9>] kernel_init+0x91/0x15d
[ 0.020456] [<ffffffff817caaa4>] kernel_thread_helper+0x4/0x10
[ 0.020471] [<ffffffff817c347c>] ? retint_restore_args+0x5/0x6
[ 0.020481] [<ffffffff817caaa0>] ? gs_change+0x13/0x13
[ 0.020500] ---[ end trace a7919e7f17c0a725 ]---
The new code will change every of the 16 low bits read from the
register and tries to write and read-back that modified number
from the MSR.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Link: http://lkml.kernel.org/r/1349797115-28346-2-git-send-email-andre.przywara@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit e9da6e9905 ("ARM: dma-mapping:
remove custom consistent dma region") removed the last users of the
field. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fix build warning in __dma_alloc() as below:
arch/arm/mm/dma-mapping.c: In function '__dma_alloc':
arch/arm/mm/dma-mapping.c:653:29: warning: 'page' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
* Fix mysterious SIGSEGV or SIGKILL in applications due to corrupting
of the %eip when returning from a signal handler.
* Fix various ARM compile issues after the merge fallout.
* Continue on making more of the Xen generic code usable by ARM platform.
* Fix SR-IOV passthrough to mirror multifunction PCI devices.
* Fix various compile warnings.
* Remove hypercalls that don't exist anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQhsIHAAoJEFjIrFwIi8fJ9LsH+gLGiF7dvFIUw1IA/Ev+tZ9Y
YFFMJwmP71ZoqrJnEH+0vXlDU7YQAF/qQysVfACfHU5en2OEO24IuINddrm3wcYU
2YAwEiLQstWhK1bhYqRqWeczjR3BV0NWtUoHpQar/5h4Ykppl5OxmXdBEfv+ThzA
ju2d9fvQoJR7flW/CsWqoNcyPubzzXWYRCBWLdChw3NXVQTr/5ZDwvkIwgk6Gv5g
vR0Qlirjdf2IyyE77zYhZw61H82IXoVCKnmif3HC1lYnSvVdVxamI0UhtXIjPJQU
KB2e9Qkfix8weXDtpNBqa/VUIW7R83qCTZszs4mD/ktPAhgvxzCF3h/XLLXuwS4=
=FR/L
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen bug-fixes from Konrad Rzeszutek Wilk:
- Fix mysterious SIGSEGV or SIGKILL in applications due to corrupting
of the %eip when returning from a signal handler.
- Fix various ARM compile issues after the merge fallout.
- Continue on making more of the Xen generic code usable by ARM
platform.
- Fix SR-IOV passthrough to mirror multifunction PCI devices.
- Fix various compile warnings.
- Remove hypercalls that don't exist anymore.
* tag 'stable/for-linus-3.7-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: dbgp: Fix warning when CONFIG_PCI is not enabled.
xen: arm: comment on why 64-bit xen_pfn_t is safe even on 32 bit
xen: balloon: use correct type for frame_list
xen/x86: don't corrupt %eip when returning from a signal handler
xen: arm: make p2m operations NOPs
xen: balloon: don't include e820.h
xen: grant: use xen_pfn_t type for frame_list.
xen: events: pirq_check_eoi_map is X86 specific
xen: XENMEM_translate_gpfn_list was remove ages ago and is unused.
xen: sysfs: fix build warning.
xen: sysfs: include err.h for PTR_ERR etc
xen: xenbus: quirk uses x86 specific cpuid
xen PV passthru: assign SR-IOV virtual functions to separate virtual slots
xen/xenbus: Fix compile warning.
xen/x86: remove duplicated include from enlighten.c
... and fix the race in updating unaligned control ones
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add dmtimer clock aliases for AM33XX devices so that the parent clock for
the dmtimer can be set correctly by the dmtimer driver. Without these clock
aliases the dmtimer driver will fail to find the parent clocks for the dmtimer.
Verified that DMTIMERs can be successfully requested on AM335x beagle bone.
Original patch was provided by Vaibhav Hiremath [1]. Changelog and
additional verification performed by Jon Hunter.
[1] http://marc.info/?l=linux-omap&m=134693631608018&w=2
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull perf fixes from Ingo Molnar:
"Most of these are uprobes race fixes from Oleg, and their preparatory
cleanups. (It's larger than what I'd normally send for an -rc kernel,
but they looked significant enough to not delay them.)
There's also an oprofile fix and an uncore PMU fix."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
perf/x86: Disable uncore on virtualized CPUs
oprofile, x86: Fix wrapping bug in op_x86_get_ctrl()
ring-buffer: Check for uninitialized cpu buffer before resizing
uprobes: Fix the racy uprobe->flags manipulation
uprobes: Fix prepare_uprobe() race with itself
uprobes: Introduce prepare_uprobe()
uprobes: Fix handle_swbp() vs unregister() + register() race
uprobes: Do not delete uprobe if uprobe_unregister() fails
uprobes: Don't return success if alloc_uprobe() fails
uprobes/x86: Only rep+nop can be emulated correctly
uprobes: Simplify is_swbp_at_addr(), remove stale comments
uprobes: Kill set_orig_insn()->is_swbp_at_addr()
uprobes: Introduce copy_opcode(), kill read_opcode()
uprobes: Kill set_swbp()->is_swbp_at_addr()
uprobes: Restrict valid_vma(false) to skip VM_SHARED vmas
uprobes: Change valid_vma() to demand VM_MAYEXEC rather than VM_EXEC
uprobes: Change write_opcode() to use FOLL_FORCE
uprobes: Move clear_thread_flag(TIF_UPROBE) to uprobe_notify_resume()
uprobes: Kill UTASK_BP_HIT state
uprobes: Fix UPROBE_SKIP_SSTEP checks in handle_swbp()
...
Pull s390 fixes from Martin Schwidefsky:
"Among the usual minor bug fixes the more interesting patches are the
perf counters for the latest machine, the missing select to enable
transparent huge pages and a build fix for the UAPI rework."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390,uapi: do not use uapi/asm-generic/kvm_para.h
s390/cache: fix data/instruction cache output
s390: fix linker script for 31 bit builds
s390/thp: select HAVE_ARCH_TRANSPARENT_HUGEPAGE
s390/kdump: Use 64 bit mode for 0x10000 entry point
perf_cpum_cf: Add support for counters available with IBM zEC12
s390/css: stop stsch loop after cc 3
s390/cio: use generic bitmap functions
s390/chpid: make headers usable (again)
Pull tile fixes from Chris Metcalf:
"This fixes one issue with compiler flags that can cause modules not to
load, and cleans up some warnings with ELF_R_xxx defines."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: avoid build warnings from duplicate ELF_R_xxx #defines
arch/tile: avoid generating .eh_frame information in modules
Even if it works with since the types have the same size, the correct
type of the last __ioremap() argument is pgprot_t rather than pteval_t.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
These are now provided in <asm-generic/module.h>, so clean up warnings
by not re-defining them in module.c.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
The tile tool chain uses the .eh_frame information for backtracing.
The vmlinux build drops any .eh_frame sections at link time, but when
present in kernel modules, it causes a module load failure due to the
presence of unsupported pc-relative relocations. When compiling to
use compiler feedback support, the compiler by default omits .eh_frame
information, so we don't see this problem. But when not using feedback,
we need to explicitly suppress the .eh_frame.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org
Without the patch, kind of below warning will be dumped if DMA-API
debug is enabled:
[ 11.069763] ------------[ cut here ]------------
[ 11.074645] WARNING: at lib/dma-debug.c:948 check_unmap+0x770/0x860()
[ 11.081420] ehci-omap ehci-omap.0: DMA-API: device driver failed to
check map error[device address=0x0000000
0adb78e80] [size=8 bytes] [mapped as single]
[ 11.095611] Modules linked in:
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
After commit 24d7b40a60 (ARM: OMAP2+:
PM: MPU DVFS: use generic CPU device for MPU-SS), OPPs are registered
using an existing CPU device, not the omap_device for MPU-SS.
First, fix the board file to use get_cpu_device() as required by the
above commit, otherwise custom OPPs will be added to the wrong device.
Second, the board files OPP init is called from the its init_machine
method, and the generic CPU devices are not yet created when
init_machine is run. Therefore OPP initialization will fail. To fix,
use a device_initcall() for the board file's OPP customization, and
make the device_initcall board-specific by using a machine_is check.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Both these features have been around for a long time now, and haven't
had any recent issues brought up. So lets drop their experimental
status.
In any case, hotplugis selected by other non-experimental options
which then cause a Kconfig warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On n900 uart1 pins are not not used for uart, instead they are
used to connect to a cell modem over ssi. Looks like we're
currently missing these signal names for 3430 for some reason,
and only have some of them listed for 3630. Obviously the signals
are there for 3430 if n900 is using them and they are documented
in some TRMs.
Note that these will eventually be replaced by device tree
based pinctrl-single.c driver. But for now these are needed
to verify the SSI pins for devices like Nokia N900.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8f31cefe (ARM: OMAP2+: select PINCTRL in Kconfig)
added select PINCTRL, but accdentally added it to a wrong
location.
We want to select if for ARCH_OMAP2PLUS, not for
ARCH_OMAP2PLUS_TYPICAL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following errors:
[ 2.318084] omap-mcbsp 49022000.mcbsp: invalid rx DMA channel
[ 2.324432] omap-mcbsp 49024000.mcbsp: invalid rx DMA channel
Which is because we failed to link the sidetone hwmod for McBSP2/3. The
missing sidetone hwmod link will prevent omap_device_alloc() to append the
DMA resources since we - accidentally - end up having the same number of
resources provided from DT (IO/IRQ) as we have in hwmod for the McBSP ports
without the ST resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The runtime PM framework assumes that the hardware state of devices
when initialized is disabled. For all omap_devices, we idle/disable
device by default. However, the console uart uses a "no idle" option
during omap_device init in order to allow earlyprintk usage to work
seamlessly during boot.
Because the hardware is left partially enabled after init (whatever
the bootloader settings were), the omap_device should later be fully
initialized (including mux) and the runtime PM framework should be
told that the device is active, and not disabled so that the hardware
state is in sync with runtime PM state.
To fix, after the device has been created/registered, call
omap_device_enable() to finialize init and use pm_runtime_set_active()
to tell the runtime PM core the device is enabled.
Tested on 2420/n810, 3530/Overo, 3530/Beagle, 3730/OveroSTORM,
3730/Beagle-xM, 4460/PandaES.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP34xx/35xx, and OMAP36xx chips with ES < 1.2, if the PER
powerdomain goes to OSWR or OFF while CORE stays at CSWR or ON, or if,
upon chip wakeup from OSWR or OFF, the CORE powerdomain goes ON before
PER, the UART3/4 FIFOs and McBSP2/3 SIDETONE memories will be
unusable. This is erratum i582 in the OMAP36xx Silicon Errata
document.
This patch implements one of several parts of the workaround: the
addition of the wakeup dependency between the PER and WKUP
clockdomains, such that PER will wake up at the same time CORE_L3
does.
This is not a complete workaround. For it to be complete:
1. the PER powerdomain's next power state must not be set to OSWR or
OFF if the CORE powerdomain's next power state is set to CSWR or
ON;
2. the UART3/4 FIFO and McBSP2/3 SIDETONE loopback tests should be run
if the LASTPOWERSTATEENTERED bits for PER and CORE indicate that
PER went OFF while CORE stayed on. If loopback tests fail, then
those devices will be unusable until PER and CORE can undergo a
transition from ON to OSWR/OFF and back ON.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We can not directly call kvm_release_pfn_clean to release the pfn
since we can meet noslot pfn which is used to cache mmio info into
spte
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
The periodic mode is currently calculated by a simple division
but we should pay more attention to our integer arithmetics.
Also delete a comment that does not make any sense.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When booting a secondary CPU, the primary CPU hands two sets of page
tables via the secondary_data struct:
(1) swapper_pg_dir: a normal, cacheable, shared (if SMP) mapping
of the kernel image (i.e. the tables used by init_mm).
(2) idmap_pgd: an uncached mapping of the .idmap.text ELF
section.
The idmap is generally used when enabling and disabling the MMU, which
includes early CPU boot. In this case, the secondary CPU switches to
swapper as soon as it enters C code:
struct mm_struct *mm = &init_mm;
unsigned int cpu = smp_processor_id();
/*
* All kernel threads share the same mm context; grab a
* reference and switch to it.
*/
atomic_inc(&mm->mm_count);
current->active_mm = mm;
cpumask_set_cpu(cpu, mm_cpumask(mm));
cpu_switch_mm(mm->pgd, mm);
This causes a problem on ARMv7, where the identity mapping is treated as
strongly-ordered leading to architecturally UNPREDICTABLE behaviour of
exclusive accesses, such as those used by atomic_inc.
This patch re-orders the secondary_start_kernel function so that we
switch to swapper before performing any exclusive accesses.
Cc: <stable@vger.kernel.org>
Cc: David McKay <david.mckay@st.com>
Reported-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds missing initializer of .smp field of machine descriptor
of EXYNOS 4 DT machine.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- AArch64 Linux compilation fixes following 3.7-rc1 changes
(MODULES_USE_ELF_RELA, update_vsyscall() prototype)
- Unnecessary register setting in start_thread() (thanks to Al Viro)
- ptrace fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=0gQo
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
"Main changes:
- AArch64 Linux compilation fixes following 3.7-rc1 changes
(MODULES_USE_ELF_RELA, update_vsyscall() prototype)
- Unnecessary register setting in start_thread() (thanks to Al Viro)
- ptrace fixes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: fix alignment padding in assembly code
arm64: ptrace: use HW_BREAKPOINT_EMPTY type for disabled breakpoints
arm64: ptrace: make structure padding explicit for debug registers
arm64: No need to set the x0-x2 registers in start_thread()
arm64: Ignore memory blocks below PHYS_OFFSET
arm64: Fix the update_vsyscall() prototype
arm64: Select MODULES_USE_ELF_RELA
arm64: Remove duplicate inclusion of mmu_context.h in smp.c
An interesting effect of using the generic version of linkage.h
is that the padding is defined in terms of x86 NOPs, which can have
even more interesting effects when the assembly code looks like this:
ENTRY(func1)
mov x0, xzr
ENDPROC(func1)
// fall through
ENTRY(func2)
mov x0, #1
ret
ENDPROC(func2)
Admittedly, the code is not very nice. But having code from another
architecture doesn't look completely sane either.
The fix is to add arm64's version of linkage.h, which causes the insertion
of proper AArch64 NOPs.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull perf fixes from Ingo Molnar:
"Assorted small fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf python: Properly link with libtraceevent
perf hists browser: Add back callchain folding symbol
perf tools: Fix build on sparc.
perf python: Link with libtraceevent
perf python: Initialize 'page_size' variable
tools lib traceevent: Fix missed freeing of subargs in free_arg() in filter
lib tools traceevent: Add back pevent assignment in __pevent_parse_format()
perf hists browser: Fix off-by-two bug on the first column
perf tools: Remove warnings on JIT samples for srcline sort key
perf tools: Fix segfault when using srcline sort key
perf: Require exclude_guest to use PEBS - kernel side enforcement
perf tool: Precise mode requires exclude_guest
. The python binding needs to link with libtraceevent and to initialize
the 'page_size' variable so that mmaping works again.
. The callchain folding character that appears on the TUI just before
the overhead had disappeared due to recent changes, add it back.
. Intel PEBS in VT-x context uses the DS address as a guest linear address,
even though its programmed by the host as a host linear address. This either
results in guest memory corruption and or the hardware faulting and 'crashing'
the virtual machine. Therefore we have to disable PEBS on VT-x enter and
re-enable on VT-x exit, enforcing a strict exclude_guest.
Kernel side enforcement fix by Peter Zijlstra, tooling side fix by David Ahern.
. Fix build on sparc due to UAPI, fix from David Miller.
. Fixes for the srclike sort key for unresolved symbols and when processing
samples in JITted code, where we don't have an ELF file, just an special
symbol table, fixes from Namhyung Kim.
. Fix some leaks in libtraceevent, from Steven Rostedt.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=DTM3
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
* The python binding needs to link with libtraceevent and to initialize
the 'page_size' variable so that mmaping works again.
* The callchain folding character that appears on the TUI just before
the overhead had disappeared due to recent changes, add it back.
* Intel PEBS in VT-x context uses the DS address as a guest linear address,
even though its programmed by the host as a host linear address. This either
results in guest memory corruption and or the hardware faulting and 'crashing'
the virtual machine. Therefore we have to disable PEBS on VT-x enter and
re-enable on VT-x exit, enforcing a strict exclude_guest.
Kernel side enforcement fix by Peter Zijlstra, tooling side fix by David Ahern.
* Fix build on sparc due to UAPI, fix from David Miller.
* Fixes for the srclike sort key for unresolved symbols and when processing
samples in JITted code, where we don't have an ELF file, just an special
symbol table, fixes from Namhyung Kim.
* Fix some leaks in libtraceevent, from Steven Rostedt.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A set of fixes and some minor cleanups for -rc2:
- A series from Arnd that fixes warnings in drivers and other code
included by ARM defconfigs. Most have been acked by corresponding
maintainers (and seem quite hard to argue not picking up anyway in the
few exception cases).
- A few misc patches from the list for integrator/vt8500/i.MX
- A batch of fixes to OMAP platforms, fixing:
- boot problems on beaglebone,
- regression fixes for local timers
- clockdomain locking fixes
- a few boot/sparse warnings
- For Tegra:
- Clock rate calculation overflow fix
- Revert a change that removed timer clocks and a fix for symbol name clashes
- For Renesas:
- IO accessor / annotation cleanups to remove warnings
- For Kirkwood/Dove/mvebu:
- Fixes for device trees for Dove (some minor cleanups, some fixes)
- Fixes for the mvebu gpio driver
- Fix build problem for Feroceon due to missing ifdefs
- Fix lsxl DTS files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=alOZ
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc fixes from Olof Johansson:
"A set of fixes and some minor cleanups for -rc2:
- A series from Arnd that fixes warnings in drivers and other code
included by ARM defconfigs. Most have been acked by corresponding
maintainers (and seem quite hard to argue not picking up anyway in
the few exception cases).
- A few misc patches from the list for integrator/vt8500/i.MX
- A batch of fixes to OMAP platforms, fixing:
- boot problems on beaglebone,
- regression fixes for local timers
- clockdomain locking fixes
- a few boot/sparse warnings
- For Tegra:
- Clock rate calculation overflow fix
- Revert a change that removed timer clocks and a fix for symbol
name clashes
- For Renesas:
- IO accessor / annotation cleanups to remove warnings
- For Kirkwood/Dove/mvebu:
- Fixes for device trees for Dove (some minor cleanups, some fixes)
- Fixes for the mvebu gpio driver
- Fix build problem for Feroceon due to missing ifdefs
- Fix lsxl DTS files"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: kirkwood: fix buttons on lsxl boards
ARM: kirkwood: fix LEDs names for lsxl boards
ARM: Kirkwood: fix disabling CACHE_FEROCEON_L2
gpio: mvebu: Add missing breaks in mvebu_gpio_irq_set_type
ARM: dove: Add crypto engine to DT
ARM: dove: Remove watchdog from DT
ARM: dove: Restructure SoC device tree descriptor
ARM: dove: Fix clock names of sata and gbe
ARM: dove: Fix tauros2 device tree init
ARM: dove: Add pcie clock support
ARM: OMAP2+: Allow kernel to boot even if GPMC fails to reserve memory
ARM: OMAP: clockdomain: Fix locking on _clkdm_clk_hwmod_enable / disable
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
ARM: OMAP4: devices: fixup OMAP4 DMIC platform device error message
ARM: OMAP2+: clock data: Add dev-id for the omap-gpmc dummy fck
ARM: OMAP: resolve sparse warning concerning debug_card_init()
ARM: OMAP4: Fix twd_local_timer_register regression
ARM: tegra: add tegra_timer clock
ARM: tegra: rename tegra system timer
...
A collection of warning fixes on non-ARM code from Arnd Bergmann:
* 'testing/driver-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: s3c: mark s3c2440_clk_add as __init_refok
spi/s3c64xx: use correct dma_transfer_direction type
pcmcia: sharpsl: don't discard sharpsl_pcmcia_ops
USB: EHCI: mark ehci_orion_conf_mbus_windows __devinit
mm/slob: use min_t() to compare ARCH_SLAB_MINALIGN
SCSI: ARM: make fas216_dumpinfo function conditional
SCSI: ARM: ncr5380/oak uses no interrupts
Pull miscellaneous x86 fixes from Peter Anvin:
"The biggest ones are fixing suspend/resume breakage on 32 bits, and an
interrim fix for mapping over holes that allows AMD kit with more than
1 TB.
A final solution for the latter is in the works, but involves some
fairly invasive changes that will probably mean it will only be
appropriate for 3.8."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, MCE: Remove bios_cmci_threshold sysfs attribute
x86, amd, mce: Avoid NULL pointer reference on CPU northbridge lookup
x86: Exclude E820_RESERVED regions and memory holes above 4 GB from direct mapping.
x86/cache_info: Use ARRAY_SIZE() in amd_l3_attrs()
x86/reboot: Remove quirk entry for SBC FITPC
x86, suspend: Correct the restore of CR4, EFER; skip computing EFLAGS.ID
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Vb/G
-----END PGP SIGNATURE-----
Merge tag 'xtensa-next-20121018' of git://github.com/czankel/xtensa-linux
Pull Xtensa patchset from Chris Zankel:
"These are all limited to the xtensa subtree and include some important
changes (adding long missing system calls for newer libc versions and
other fixes) and the UAPI changes"
* tag 'xtensa-next-20121018' of git://github.com/czankel/xtensa-linux:
xtensa: add missing system calls to the syscall table
xtensa: minor compiler warning fix
xtensa: Use Kbuild infrastructure to handle asm-generic headers
UAPI: (Scripted) Disintegrate arch/xtensa/include/asm
xtensa: fix unaligned usermode access
xtensa: reorganize SR referencing
xtensa: fix boot parameters parsing
xtensa: fix missing return in do_page_fault for SIGBUS case
xtensa: copy_thread with CLONE_VM must not copy live parent AR windows
xtensa: fix memmove(), bcopy(), and memcpy().
xtensa: ISS: fix rs_put_char
xtensa: ISS: fix specific simcalls
* commit 'v3.7-rc1': (10892 commits)
Linux 3.7-rc1
x86, boot: Explicitly include autoconf.h for hostprogs
perf: Fix UAPI fallout
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate include/linux/byteorder
UAPI: (Scripted) Disintegrate include/linux
UAPI: Unexport linux/blk_types.h
UAPI: Unexport part of linux/ppp-comp.h
perf: Handle new rbtree implementation
procfs: don't need a PATH_MAX allocation to hold a string representation of an int
vfs: embed struct filename inside of names_cache allocation if possible
audit: make audit_inode take struct filename
vfs: make path_openat take a struct filename pointer
vfs: turn do_path_lookup into wrapper around struct filename variant
audit: allow audit code to satisfy getname requests from its names_list
vfs: define struct filename and have getname() return it
btrfs: Fix compilation with user namespace support enabled
userns: Fix posix_acl_file_xattr_userns gid conversion
userns: Properly print bluetooth socket uids
...
In 32 bit guests, if a userspace process has %eax == -ERESTARTSYS
(-512) or -ERESTARTNOINTR (-513) when it is interrupted by an event
/and/ the process has a pending signal then %eip (and %eax) are
corrupted when returning to the main process after handling the
signal. The application may then crash with SIGSEGV or a SIGILL or it
may have subtly incorrect behaviour (depending on what instruction it
returned to).
The occurs because handle_signal() is incorrectly thinking that there
is a system call that needs to restarted so it adjusts %eip and %eax
to re-execute the system call instruction (even though user space had
not done a system call).
If %eax == -514 (-ERESTARTNOHAND (-514) or -ERESTART_RESTARTBLOCK
(-516) then handle_signal() only corrupted %eax (by setting it to
-EINTR). This may cause the application to crash or have incorrect
behaviour.
handle_signal() assumes that regs->orig_ax >= 0 means a system call so
any kernel entry point that is not for a system call must push a
negative value for orig_ax. For example, for physical interrupts on
bare metal the inverse of the vector is pushed and page_fault() sets
regs->orig_ax to -1, overwriting the hardware provided error code.
xen_hypervisor_callback() was incorrectly pushing 0 for orig_ax
instead of -1.
Classic Xen kernels pushed %eax which works as %eax cannot be both
non-negative and -RESTARTSYS (etc.), but using -1 is consistent with
other non-system call entry points and avoids some of the tests in
handle_signal().
There were similar bugs in xen_failsafe_callback() of both 32 and
64-bit guests. If the fault was corrected and the normal return path
was used then 0 was incorrectly pushed as the value for orig_ax.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This makes common code less ifdef-y and is consistent with PVHVM on
x86.
Also note that phys_to_machine_mapping_valid should take a pfn
argument and make it do so.
Add __set_phys_to_machine, make set_phys_to_machine a simple wrapper
(on systems with non-nop implementations the outer one can allocate
new p2m pages).
Make __set_phys_to_machine check for identity mapping or invalid only.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This correctly sizes it as 64 bit on ARM but leaves it as unsigned
long on x86 (therefore no intended change on x86).
The long and ulong guest handles are now unused (and a bit dangerous)
so remove them.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Define PRI macros for xen_ulong_t and xen_pfn_t and use to fix:
drivers/xen/sys-hypervisor.c:288:4: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'xen_ulong_t' [-Wformat]
Ideally this would use PRIx64 on ARM but these (or equivalent) don't
seem to be available in the kernel.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
CC: stable@vger.kernel.org
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull hexagon updates from Richard Kuo:
"It includes the Hexagon UAPI changes from David Howells and some CR
marking changes for the transition from Code Aurora to Linux
Foundation."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
Hexagon: Copyright marking changes
UAPI: (Scripted) Disintegrate arch/hexagon/include/asm
This is a couple of high code motion patches (all within arch/parisc) I'd like
to apply at -rc1 to avoid conflicts with anything else. One moves us on to
the generated instead of included asm file model and the other is a pull
request from David Howells for UAPI disintegration.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQgY1yAAoJEDeqqVYsXL0MEmMH/R4MUjwPUE8FsAylREzOt3Ej
HSTHLzLSgAsIseQY8z3pyPPpZem/50ti3jYGZDWPyTZd2VoGeYvbPOew/c08C86c
r2RoNHQb6sYX0LcjAPGIiKZ7ft7p/CUus0v07IX6xnIqH4y2TY/26b67VhcNyTdn
MWYZ55q6Zc+EsyZZbH7eq0hRTubSpx/cXIc15pgJmt+LvikVDFjB9sYieAZVSTiF
ATCRkyzR6lxLkyYiG0K56h7Qdjz9IAn2b0tUYax0Gf/96K7Zo0nhNmv6RPD5DNbN
dwBeKi/e62DI/KY6xm/znyFdRW5TGCxxip5ZFD7fcD7DQ5y9Ap6GCw+7TF9z6ok=
=GU0H
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
Pull PARISC changes from James Bottomley:
"This is a couple of high code motion patches (all within arch/parisc)
I'd like to apply at -rc1 to avoid conflicts with anything else. One
moves us on to the generated instead of included asm file model and
the other is a pull request from David Howells for UAPI
disintegration.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'parisc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
UAPI: (Scripted) Disintegrate arch/parisc/include/asm
[PARISC] asm: redo generic includes
Add the following system calls to the syscall table:
fallocate
sendmmsg
umount2
syncfs
epoll_create1
inotify_init1
signalfd4
dup3
pipe2
timerfd_create
timerfd_settime
timerfd_gettime
eventfd2
preadv
pwritev
fanotify_init
fanotify_mark
process_vm_readv
process_vm_writev
name_to_handle_at
open_by_handle_at
sync_file_range
perf_event_open
rt_tgsigqueueinfo
clock_adjtime
prlimit64
kcmp
Note that we have to use the 'sys_sync_file_range2' version, so that
the 64-bit arguments are aligned correctly to the argument registers.
Signed-off-by: Chris Zankel <chris@zankel.net>
Fix two compiler warnings complaining about truncating a value on
a 64-bit host, and about declaring an unused variable that is only
used for a specific configuration.
Signed-off-by: Chris Zankel <chris@zankel.net>
From Borislav Petkov <bp@amd64.org>:
Below is a RAS fix which reverts the addition of a sysfs attribute
which we agreed is not needed, post-factum. And this should go in now
because that sysfs attribute is going to end up in 3.7 otherwise and
thus exposed to userspace; removing it then would be a lot harder.
This is done as a merge rather than a simple patch/cherry-pick since
the baseline for this patch was not in the previous x86/urgent.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
450cc20103 ("x86/mce: Provide boot argument to honour bios-set CMCI
threshold") added the bios_cmci_threshold sysfs attribute which was
supposed to communicate to userspace tools that BIOS CMCI threshold has
been honoured.
However, this info is not of any importance to userspace - it should
rather get the actual error count it has been thresholded already from
MCi_STATUS[38:52].
So drop this before it becomes a used interface (good thing we caught
this early in 3.7-rc1, right after the merge window closed).
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20121017105940.GA14590@x1.osrc.amd.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
It turns out that S390 shouldn't use uapi/asm-generic/kvm_para.h since it
defines the functions in its non-UAPI kvm_para.h file.
#including <asm-generic/kvm_para.h> will first pick up
include/asm-generic/kvm_para.h, which defines conflicting functions.
Instead, partially revert commit 0420c87e64,
ungenericising this file and just inserting a comment to prevent the patch
program from deleting it.
cc: Yuanhan Liu <yuanhan.liu@intel.com>
cc: fengguang.wu@intel.com
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
a2a47ca366
(ARM: __io abuse cleanup) cleanuped __io() -> IOMEM(),
but setup-r8a7779.c was out of target,
since it directly used (void __iomem __force *) instead of __io().
This patch cleanup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Make arch/ia64/include/asm/kvm_para.h generic since it's the same as the
asm-generic version. This deals with the problem when ia64 is compiled with
allmodconfig you get:
In file included from include/uapi/linux/kvm_para.h:26:0,
from include/linux/kvm_para.h:4,
from kernel/watchdog.c:28:
arch/ia64/include/asm/kvm_para.h:24:28: error: redefinition of 'kvm_arch_para_features'
include/asm-generic/kvm_para.h:16:28: note: previous definition of 'kvm_arch_para_features' was here
arch/ia64/include/asm/kvm_para.h:29:20: error: redefinition of 'kvm_check_and_clear_guest_paused'
include/asm-generic/kvm_para.h:11:20: note: previous definition of 'kvm_check_and_clear_guest_paused' was here
This does not happen for ia64 defconfig.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Yuanhan Liu <yuanhan.liu@intel.com>
cc: fengguang.wu@intel.com
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Calling convention for internal functions and 'asmlinkage' functions is
different on x86-32. Therefore do not directly cast aesni_enc as XTS tweak
function, but use wrapper function in between. Fixes crash with "XTS +
aesni_intel + x86-32" combination.
Cc: stable@vger.kernel.org
Reported-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a debugger tries to zero a hardware debug control register, the
kernel will try to infer both the type and length of the breakpoint
in order to sanity-check against the requested regset type. This will
fail because the encoding will appear as a zero-length breakpoint.
This patch changes the control register setting so that disabled
breakpoints are treated as HW_BREAKPOINT_EMPTY and no further
sanity-checking is required.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The user_hwdebug_state structure contains implicit padding to conform to
the alignment requirements of the AArch64 ABI (namely that aggregates
must be aligned to their most aligned member).
This patch fixes the ptrace functions operating on struct
user_hwdebug_state so that the padding is handled correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For historical reasons, ARM used to set r0-r2 in start_thread() to the
first values on the user stack when starting a new user application. The
same logic has been inherited in AArch64. The x0 register is overridden
by the sys_execve() return value so it's always zero on success. The x1
and x2 registers are ignored by AArch64 and EABI AArch32 applications,
so we can safely remove the register setting for both native and compat
user space.
This also fixes a potential fault with the kernel accessing user space
stack directly.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
According to Documentation/arm64/booting.txt, the kernel image must be
loaded at a pre-defined offset from the start of RAM so that the kernel
can calculate PHYS_OFFSET based on this address. If the DT contains
memory blocks below this PHYS_OFFSET, report them and ignore the
corresponding memory range.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
With commit 576094b7 (time: Introduce new GENERIC_TIME_VSYSCALL) the old
update_vsyscall() prototype is no longer available. This patch updates
the arm64 port.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: John Stultz <john.stultz@linaro.org>
With commit 786d35d4 (make most arch asm/module.h files use
asm-generic/module.h) arm64 needs to enable MODULES_USE_ELF_RELA for
loadable modules.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Pull MIPS fixes from Ralf Baechle:
"Random small fixes across the MIPS code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: CMP: Fix physical core number calculation logic
MIPS: JZ4740: Forward declare struct uart_port in header.
MIPS: JZ4740: Fix '#include guard' in serial.h
MIPS: hugetlbfs: Fix hazard between tlb write and pagemask restoration.
MIPS: Restore pagemask after dumping the TLB.
MIPS: Hugetlbfs: Handle huge pages correctly in pmd_bad()
MIPS: R5000: Fix TLB hazard handling.
MIPS: tlbex: Deal with re-definition of label
MIPS: Make __{,n,u}delay declarations match definitions and generic delay.h
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a handful of powerpc related fixes."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powerpc: Fix snooze state problem in the cpuidle design on pseries.
cpuidle/powerpc: Fix smt_snooze_delay functionality.
cpuidle/powerpc: Fix target residency initialisation in pseries cpuidle
powerpc: Build fix for powerpc KVM
Revert "powerpc/perf: Use pmc_overflow() to detect rolled back events"
Significant changes are:
- A regression fix for the new HD-audio LPIB delay counting,
VGA-switcheroo race fix
- ASoC ams-delta fix for the broken driver loading
Otherwise a collection of mostly small / trivial fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQgArvAAoJEGwxgFQ9KSmk91wP/2VHQ7GVshkiVCcBeRo57X3Z
4Lmt8tEm55swC/issMhRYmzFiRHQHpwEfYhXHfntjxqI9siDRGaqoFoGosV68BPp
wXA2vdcbYoZ2yxxhZbwqjzOWHkM45HM/NL6l2PGVdsn69KMNLom8TK2aMqZvy0k0
S/kCbsNlgKLglsfXDhId8ITofC/mqTp/6PV+LKslJeFaK9jdqWYsQMjDlcOObP+Q
vpHe++8BqbhYg3N8SwQKO7RDwlr9JqDaMJTVci8jkMHu0+fmUOCqXWTcOW+x49zD
YI7rdYL8Mfsv+nsn3VAg0c/ulbFOqaFzse6LvgGbzAMl1lI4dm5aCxwOsHKn6ake
VUkUqSui5saYaacBSEA4SXE10RfGUHPNjWb6sasFxGvw2ShFajcIMCt34BIieUFz
yv7D8sagRmJVmnMlZuuGmqrf2FK7bWKhrfOodGesyBwHtmU7AYnZnU9HSjROsIo9
yn53kt9NRFsy2l5CVLDGz4fDbqv9w9NZV6L+7rCReityNdWTaxlV60n8qMION/dq
8hVX2J030kY2MqUQ+XXfj1Hje6lYjVW+TW/2KfMYABz1CJ4ZJjaF8uwTo5DUoEdv
4Pumx7sYEMkaEUD8EIsRnoaNBXVTYNbtwnmlt1jlDMfZReVboIWzwjKmsC6Ug/ge
hhKKAAO0KODOZyuj9cxE
=bW/T
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Significant changes are:
- A regression fix for the new HD-audio LPIB delay counting,
VGA-switcheroo race fix
- ASoC ams-delta fix for the broken driver loading
Otherwise a collection of mostly small / trivial fixes."
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: emu10k1: add chip details for E-mu 1010 PCIe card
ALSA: hda - Always check array bounds in alc_get_line_out_pfx
ASoC: bells: Correct typo in sub speaker DAI name for WM5110
ALSA: hda - Stop LPIB delay counting on broken hardware
ALSA: hda - Fix registration race of VGA switcheroo
ALSA: hda - Clean up superfluous position_fix list entries
ALSA: ac97 - Fix missing NULL check in snd_ac97_cvol_new()
ASoC: codecs: da9055: Minor improvement in ALC calibration process
ASoC: dmaengine: Correct Makefile when sound is built as module
ASoC: fsi: don't reschedule DMA from an atomic context
ASoC: fix documentation in soc-jack
ARM: pxa: Fix build error caused by sram.h rename
ASoC: wm2200: Fix non-inverted OUT2 mute control
ASoC: wm2200: Use rev A register patches on rev B
ASoC: bells: Correct typo in sub speaker DAI name for WM5110
ASoC: ams-delta: Convert to use snd_soc_register_card()
ASoC: omap-mcpdm: Remove OMAP revision check
ASoC: Fix wrong include for McPDM
ASoC: omap-abe-twl6040: Fix typo of Vibrator
ASoC: twl6040: Fix Stream DAPM mapping
Change event type to switch for the power and autopower switches.
Additionally, this patch aligns the keycodes with the other linkstation
boards already supported by linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Don't use the specific board name in a the common device tree include file.
Instead use the common name 'lsxl'.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move the CACHE_FEROCEON_L2 test to kirkwood_l2_init, since linking
fails on the reference to feroceon_l2_init.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The sysfs and procfs output of the instruction and data caches were
wrong: the output of the data cache provided that instruction cache
values and vice versa.
Fix this by using the correct type indication when issueing the
ecag instruction.
Reported-by: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Because of a change in the s390 arch backend of binutils (commit 23ecd77
"Pick the default arch depending on the target size" in binutils repo)
31 bit builds will fail since the linker would now try to create 64 bit
binary output.
Fix this by setting OUTPUT_ARCH to s390:31-bit instead of s390.
Thanks to Andreas Krebbel for figuring out the issue.
Fixes this build error:
LD init/built-in.o
s390x-4.7.2-ld: s390:31-bit architecture of input file
`arch/s390/kernel/head.o' is incompatible with s390:64-bit output
Cc: Andreas Krebbel <Andreas.Krebbel@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The 0x10000 entry point can be called in z/Arch architecture and 64 bit
addressing mode. Therefore this patch removes the unnecessary 31 bit
switch code from the kdump startup function.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Increase the maximum number of available counters and check if
the hardware supports the counter. Support is indicated by the
version of the CPU-measurement counter facility.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add back a hunk from "4dcc2a4 s390/chsc: make headers usable"
which was lost during the merge of the UAPI patch.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The PERF_EVENT_IOC_PERIOD ioctl command can be used to change the
sample period of a running perf_event. Consequently, when calculating
the next event period, the new period will only be considered after the
previous one has overflowed.
This patch changes the calculation of the remaining event ticks so that
they are offset if the period has changed.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Andreas Sandberg <andreas.sandberg@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit c564df4db8 (ARM: 7540/1: kexec:
Check segment memory addresses) added a safety check with accidentally
reversed condition, and broke kexec functionality on ARM. Fix this.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPUNum Field in EBase register is 10bit wide, so after 1 bit right
shift, the mask value should be 0x1ff.
Signed-off-by: jerin jacob <jerinjacobk@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4420/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Based against v3.7-rc1
- Latest changes to arch/arm/mm/cache-tauros2.c
c2b7e05 ARM: cache: add dt support for tauros2 cache
Misc. fixes for latest changes to mach-dove/
Fixes build breakage for mach-dove
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQfutwAAoJEAi3KVZQDZAeJlYH/2n8rEqGCrZuU16XVl3Hwc5q
mUkF0PexHDnGGNrgfOEAIaouG3rCTVVdj+NTqnz3gK8jaJHF06tfhpwZaxymDFzW
m4Lt45IuDvU5jEuCBm1IDHWHLro/73YepZJJRt9yAwI1DdWAhUBYLS8cd7fIoLAJ
th0TI7PObmHRVlY2mS+ByuU5wnqV5mJMMPN6oU4RzO91rNuhoQRm8WvjzEs+tSfU
GluD05p/bm3dL9Aq6146h80CZn3W4SVIKeS2l/GdQV6bqaIUvsp0F3xfzggcrcLF
rZxOom72BgnEzA1enu+adJwKY8dHxOAZ4Iuf4HUXI5DKVfVCOrmJmWfp0mS8oyc=
=RP8E
-----END PGP SIGNATURE-----
Merge tag 'mvebu_dove_late_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
Misc. fixes for latest changes to mach-dove/
Fixes build breakage for mach-dove
* tag 'mvebu_dove_late_fixes_for_v3.7' of git://git.infradead.org/users/jcooper/linux:
ARM: dove: Add crypto engine to DT
ARM: dove: Remove watchdog from DT
ARM: dove: Restructure SoC device tree descriptor
ARM: dove: Fix clock names of sata and gbe
ARM: dove: Fix tauros2 device tree init
ARM: dove: Add pcie clock support
a regression fix for local timer, and a clockdomain locking fix.
Also few minor fixes for boot time and sparse warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=4meh
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.7-rc1/fixes-take5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
A boot problem fix for am33xx beaglebone caused by GPMC,
a regression fix for local timer, and a clockdomain locking fix.
Also few minor fixes for boot time and sparse warnings.
* tag 'omap-for-v3.7-rc1/fixes-take5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Allow kernel to boot even if GPMC fails to reserve memory
ARM: OMAP: clockdomain: Fix locking on _clkdm_clk_hwmod_enable / disable
ARM: OMAP4: devices: fixup OMAP4 DMIC platform device error message
ARM: OMAP2+: clock data: Add dev-id for the omap-gpmc dummy fck
ARM: OMAP: resolve sparse warning concerning debug_card_init()
ARM: OMAP4: Fix twd_local_timer_register regression
This branch contains a couple small fixes for Tegra for 3.7.
* A fix for another clock rate calculation overflow
* A revert of a change that removed the "timer" clock on Tegra, coupled
with a fix for the confusing symbol name clash that triggered it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Cjt7
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-fixes-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into fixes
From Stephen Warren: ARM: tegra: fixes for 3.7-rc2
This branch contains a couple small fixes for Tegra for 3.7.
* A fix for another clock rate calculation overflow
* A revert of a change that removed the "timer" clock on Tegra, coupled
with a fix for the confusing symbol name clash that triggered it.
* tag 'tegra-for-3.7-fixes-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: add tegra_timer clock
ARM: tegra: rename tegra system timer
ARM: tegra30: clk: Fix output_rate overflow
Signed-off-by: Olof Johansson <olof@lixom.net>
Earlier without cpuidle framework on pseries, the native arch
idle routine comprised of both snooze and nap
states. smt_snooze_delay variable was used to delay
the idle process entry to deeper idle state like nap.
With the coming of cpuidle, this arch specific idle was replaced
by two different idle routines, one for supporting snooze and other
for nap. This enabled addition of more
low level idle states on pseries in the future.
On adopting the generic cpuidle framework for POWER systems,
the decision of which idle state to choose from, given a predicted
idle time is taken by the menu governor based on
target_residency and exit_latency of the idle states.
target_residency is the minimum time to be resident in that idle state.
Exit_latency is time taken to exit out of idle state.
Deeper the idle state, both the target residency and exit latency
would be higher.
In the current design, smt_snooze_delay is used as target_residency
for the snooze state which is incorrect, as it is not the
minimum but the maximum duration to be in snooze state.
This would result in the governor in taking bad decision,
as presently target_residency of nap < target_residency of snooze
inspite of nap being deeper idle state.
This patch aims to fix this problem by replacing the smt_snooze_delay loop
in snooze state, with the need_resched() as the governor is aware of
entry and exit of various idle transitions based on which
next idle time prediction.
The governor is intelligent enough to determine the idle state the needs to
be transitioned to and maintains a whole of heuristics including
io load, previous idle states predictions etc for the same, based on
which idle state entry decision is taken.
With this fix, of setting target_residency of snooze to 0
nap to smt_snooze_delay
if the predicted idle time is less
than smt_snooze_delay (target_residency of nap)
value governor would pick snooze state, else nap. This adhers to the
previous native idle design.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
smt_snooze_delay was designed to delay idle loop's nap entry
in the native idle code before it got ported over to use as part of
the cpuidle framework.
A -ve value assigned to smt_snooze_delay should result in
busy looping, in other words disabling the entry to nap state.
- https://lists.ozlabs.org/pipermail/linuxppc-dev/2010-May/082450.html
This particular functionality can be achieved currently by
echo 1 > /sys/devices/system/cpu/cpu*/state1/disable
but it is broken when one assigns -ve value to the smt_snooze_delay
variable either via sysfs entry or ppc64_cpu util.
This patch aims to fix this, by disabling nap state when smt_snooze_delay
variable is set to -ve value.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the redundant target residency initialisation in pseries_cpuidle_driver_init().
This is currently over-writing the residency time updated as part of the static
table, resulting in all the idle states having the same target
residency of 100us which is incorrect. This may result in the menu governor making
wrong state decisions.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix build failure for powerpc KVM by adding missing VPN_SHIFT definition
and the ';'
arch/powerpc/kvm/book3s_32_mmu_host.c: In function 'kvmppc_mmu_map_page':
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: 'VPN_SHIFT' undeclared (first use in this function)
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: (Each undeclared identifier is reported only once
arch/powerpc/kvm/book3s_32_mmu_host.c:176: error: for each function it appears in.)
arch/powerpc/kvm/book3s_32_mmu_host.c:178: error: expected ';' before 'next_pteg'
arch/powerpc/kvm/book3s_32_mmu_host.c:190: error: label 'next_pteg' used but not defined
make[1]: *** [arch/powerpc/kvm/book3s_32_mmu_host.o] Error 1
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUH60qBOxKuMESys7AQKQkw/+OB9DOP86qLEpNBNt5Ue4Ee8G6F6oj32M
eUIH71iD9HWVbEsWwwhXZmZcGOJzLbfX4cN2FIiFl4Jxxj3NwDE7GJMRY2sOBp+q
SYrUVahcpHM4CDaFX6778pSAicM7cb7F5FyPPF7C0y39bor/Znm9SMmP83oyYcwo
smYO6NVl3Qi9b0xlHIYLE3BadO7SIGHt5crqDqZMNue1jiTox/4lliIIGer4rr3q
NaJjW2P19pG+ok0HNzHmhBKp+wpila9+TgQHsZjE+u6DizGsxxq6fiPi6A8EWAA/
mEPJQW73qeNA/kzEwjmvEoVNoOd+X3kT+cpaMegKT4BQdLyi6LtAlhw5RMXLPucd
KvmYTFxcMxxNlQbD28hCdm1kTj6cOaZS96bpz4mwYXMOlljLyi49XEceh7G9ue1S
0fOds/maCLPNcxyThcrP12pIn3Ou9ZpL7UjQKvNeZirVed25hi2lkbza9UeRRYRu
y13ELZKges9I2BQ3moMOSZ7TnUGepP8ohnVJnE8w7hegrz2L7WkNPdbuYEV5lqoP
jJVtf5pjvjhLAGUPvzWWgH2sbV12U+Fi35A5+YELoqd+OXU/gCSU1YeeeotAFdst
gka9HloiYQHSWLbj/1SXUo058WI6/dNwZcj1KznJrBkk87V48SM4BPsZ4zbt7nww
19Fr3cD7YMY=
=UV14
-----END PGP SIGNATURE-----
Merge tag 'uapi-fixes-20121017' of git://git.infradead.org/users/dhowells/linux-headers
Pull misc UAPI fixes from David Howells:
"They do a number of things:
(1) Import a patch from Catalin Marinas to extend the generic-y in
Kbuild facility to uapi directories.
(2) Make arch/tile's ucontext.h file use (1) and remove the header-y
line from the kernel internal side of things.
(3) Remove some now-empty conditional bits from include/linux/Kbuild.
The contents got moved to the UAPI side of things along with new
conditionals.
(4) Deal with now-empty files:
(a) Empty Kbuild files under include/ get removed.
(b) Empty Kbuild files under arch/ get comments to hold them as
they are likely to end up with generic-y or genhdr-y lines.
Deleting them appears to work if we want to go that route.
(c) Put a comment into uapi/asm-generic/kvm_para.h to prevent the
patch program from deleting that, and made the arches with
empty kvm_para.h uapi files use that instead of having their
own files.
(d) Put comments into four other empty uapi/ headers to prevent the
patch program from deleting them.
A question: Is this the right way to deal with the now-empty Kbuild
files?
The ones under include/ are unlikely to be used - even for generated
files, I think - so getting rid of them is probably okay. Once all
the bits are in, we can probably remove all the Kbuild files under
include/ that aren't also under include/uapi/.
The ones under arch/ are more of an issue because of the potential for
generic-y and genhdr-y."
* tag 'uapi-fixes-20121017' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Make arch/sparc/include/uapi/asm/sigcontext.h non-empty
UAPI: Make arch/sh/include/uapi/asm/hw_breakpoint.h non-empty
UAPI: Make arch/mn10300/include/uapi/asm/setup.h non-empty
UAPI: Put a comment into uapi/asm-generic/kvm_para.h and use it from arches
UAPI: The tile arch uses the generic ucontext.h file
UAPI: Place comments in empty arch Kbuilds to make them non-empty
UAPI: Remove empty non-UAPI Kbuild files
UAPI: Remove empty conditionals from include/linux/Kbuild
UAPI: Make uapi/linux/irqnr.h non-empty
uapi: Allow automatic generation of uapi/asm/ header files
Pull sparc fixes from David Miller:
"Two sparc64 perf bug fixes and add a sysrq facility so I can diagnose
these kinds of problems more quickly in the future."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix bit twiddling in sparc_pmu_enable_event().
sparc64: Add global PMU register dumping via sysrq.
sparc64: Like x86 we should check current->mm during perf backtrace generation.
When booting on a federated multi-server system (NumaScale), the
processor Northbridge lookup returns NULL; add guards to prevent this
causing an oops.
On those systems, the northbridge is accessed through MMIO and the
"normal" northbridge enumeration in amd_nb.c doesn't work since we're
generating the northbridge ID from the initial APIC ID and the last
is not unique on those systems. Long story short, we end up without
northbridge descriptors.
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Cc: stable@vger.kernel.org # 3.6
Link: http://lkml.kernel.org/r/1349073725-14093-1-git-send-email-daniel@numascale-asia.com
[ Boris: beef up commit message ]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
On systems with very large memory (1 TB in our case), BIOS may report a
reserved region or a hole in the E820 map, even above the 4 GB range. Exclude
these from the direct mapping.
[ hpa: this should be done not just for > 4 GB but for everything above the legacy
region (1 MB), at the very least. That, however, turns out to require significant
restructuring. That work is well underway, but is not suitable for rc/stable. ]
Cc: stable@kernel.org # > 2.6.32
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Link: http://lkml.kernel.org/r/1319145326-13902-1-git-send-email-jacob.shin@amd.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Make use of DT support for the crypto engine on dove and remove
the obsolete init call.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The watchdog on dove requires an interrupt that is not yet
available on DT. Therefore, the watchdog DT node is removed
until the corresponding chained intc is available.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds proper ranges for all mapped addresses within
dove SoC and moves the interrupt controller node inside the simple-bus
node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch fixes wrong clock names of lately added clock gates
for sata and gbe (mv64xx_eth).
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
During the review process of dove DT patches, Tauros2 cache
init call was changed and DT support added. This patch fixes
the call to Tauros2 init and adds a DT node. Moreover, plat/irq.h
include was missing from mach-dove/common.c.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
As dove now has clock gating control ensure pcie ports grab their
clocks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently, if the GPMC driver fails to reserve memory when probed we will
call BUG() and the kernel will not boot. Instead of calling BUG(), return
an error from probe and allow kernel to boot.
Boot tested on AM335x beagle bone board and OMAP4430 Panda board.
V2 changes:
- Ensure that clock and memory resources are released on error.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previously the code only acquired spinlock after increasing / decreasing
the usecount value, which is wrong. This leaves a small window where
a task switch may occur between the check of the usecount and the actual
wakeup / sleep of the domain. Fixed by moving the spinlock locking before
the usecount access. Left the usecount as atomic_t if someone wants an
easy access to the parameter through atomic_read.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Simon Horman:
"Please consider the following fix for the KZM-A9-GT board for 3.7.
They both resolve fallout from recent IOMEM() changes."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: use __iomem pointers for MMIO
ARM: shmobile: armadillo800eva: __io abuse cleanup
s3c2440_clk_add is a subsys_interface method and calls clkdev_add_table,
which is marked as __init. The modpost script complains about this
because we must not call an __init function from a function in the .text
section, and we cannot reference an __init function from a subsys_interface
pointer.
I have verified that the only code path into s3c2440_clk_add() is
from "int __init s3c2440_init(void)", so s3c2440_clk_add can be marked
__init_refok instead.
Without this patch, building mini2440_defconfig results in:
WARNING: vmlinux.o(.text+0x9848): Section mismatch in reference from the function s3c2440_clk_add() to the function .init.text:clkdev_add_table()
The function s3c2440_clk_add() references
the function __init clkdev_add_table().
This is often because s3c2440_clk_add lacks a __init
annotation or the annotation of clkdev_add_table is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Nothing too exciting except for the ams-delta change which is relatively
lerge due to the fact that the driver loading had been totally broken as
the driver needed a newer API to function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lEIC
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
Nothing too exciting except for the ams-delta change which is relatively
lerge due to the fact that the driver loading had been totally broken as
the driver needed a newer API to function.
arch/sparc/include/uapi/asm/sigcontext.h was emitted by the UAPI disintegration
script as an empty file because the parent file had no UAPI stuff in it,
despite being marked with "header-y".
Unfortunately, the patch program deletes resultant empty files when applying a
kernel patch.
So just stick a comment in there as a placeholder.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: David S. Miller <davem@davemloft.net>
cc: sparclinux@vger.kernel.org
arch/sh/include/uapi/asm/hw_breakpoint.h was emitted by the UAPI disintegration
script as an empty file because the parent file had no UAPI stuff in it,
despite being marked with "header-y".
Unfortunately, the patch program deletes resultant empty files when applying a
kernel patch.
So just stick a comment in there as a placeholder.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Paul Mundt <lethal@linux-sh.org>
cc: linux-sh@vger.kernel.org
arch/mn10300/include/uapi/asm/setup.h was emitted by the UAPI disintegration
script as an empty file because the parent file had no UAPI stuff in it,
despite being marked with "header-y".
Unfortunately, the patch program deletes resultant empty files when applying a
kernel patch.
So just stick a comment in there as a placeholder.
Signed-off-by: David Howells <dhowells@redhat.com>
Make uapi/asm-generic/kvm_para.h non-empty by addition of a comment to stop
the patch program from deleting it when it creates it.
Then delete empty arch-specific uapi/asm/kvm_para.h files and tell the Kbuild
files to use the generic instead.
Should this perhaps instead be a #warning or #error that the facility is
unsupported on this arch?
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Arnd Bergmann <arnd@arndb.de>
cc: Avi Kivity <avi@redhat.com>
cc: Marcelo Tosatti <mtosatti@redhat.com>
cc: kvm@vger.kernel.org
Move the header-y and generic-y lines for ucontext.h from
arch/tile/include/asm/Kbuild to the uapi/ Kbuild as the asm-generic variant is
used.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Chris Metcalf <cmetcalf@tilera.com>
Place comments in:
arch/mips/include/asm/Kbuild
arch/tile/include/arch/Kbuild
to make them non-empty so that the patch program doesn't remove them when it
reduces them to nothing.
Possibly they should be just deleted, but it's possible that they'll acquire
generic-y or genhdr-y lines in future, so I'm keeping them around for the
moment.
Note that MIPS will compile happily if the file is deleted instead. I haven't
tested TILE, but I suspect it will be the same there.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Ralf Baechle <ralf@linux-mips.org>
cc: Chris Metcalf <cmetcalf@tilera.com>
Since the maximum section size on mach-exynos is set to 256MiB, boards
with memory configuration defined using sections bigger than 256MiB will
fail to boot with a kernel panic.
This patch modifies the dts file of Samsung Trats board to define four
sections of 256MiB instead of two of 512MiB to fix the boot problem.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit a5238e360b (spi: s3c64xx: move controller information into driver
data) introduced separate device names for the different subtypes of the
spi controller but forgot to set these in the relevant machines.
To fix this introduce a s3c64xx_spi_setname function and populate all
Samsung arches with the correct names. The function resides in a new
header, as the s3c64xx-spi.h contains driver platform data and should
therefore at some later point move out of the Samsung include dir.
Tested on a s3c2416-based machine.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Cc: Stable <stable@vger.kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[s.nawrocki@samsung.com: tested on mach-exynos]
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEUEABECAAYFAlB7pNUACgkQGkmNcg7/o7jjUgCgoki88QEhqCSwo7oHwTTKc101
K0gAli6kneoMMHfO9w9dMlGz78EI5FQ=
=JEFo
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt.
The bulk of this is the UAPI disintegration for SH.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix up more fallout from pointless ARM __iomem churn.
sh: Wire up kcmp syscall.
UAPI: (Scripted) Disintegrate arch/sh/include/asm
Add __pminitconst to fix the build, otherwise the following error can occur:
arch/frv/kernel/setup.c:187:47: error: expected '=', ',', ';', 'asm' or '__attribute__' before '*' token
arch/frv/kernel/setup.c:386:2: error: 'clock_cmodes' undeclared (first use in this function)
arch/frv/kernel/setup.c:571:6: error: 'clock_cmodes' undeclared (first use in this function)
make[2]: *** [arch/frv/kernel/setup.o] Error 1
http://kisskb.ellerman.id.au/kisskb/buildresult/7344691/
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an incorrect symbol in copy_thread():
arch/frv/kernel/process.c: In function 'copy_thread':
arch/frv/kernel/process.c:197: error: 'chilregs' undeclared (first use in this function)
arch/frv/kernel/process.c:197: error: (Each undeclared identifier is reported only once
arch/frv/kernel/process.c:197: error: for each function it appears in.)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix VLIW packing constraint violation in entry.S:
arch/frv/kernel/entry.S: Assembler messages:
arch/frv/kernel/entry.S:871: Error: VLIW packing constraint violation
When packing CALLL with OR, CALLL must go in the first slot. The
instructions are executed simultaneously, so it doesn't matter which way
round they're packed from that point of view.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- duplicate includes, section markup, code mishaps
- erroneous return value in errorpath on the bcm2835 driver
- remove an unused sirf function that was causing build errors
- multiple-platform compilation stubs and a missed code review
comment fixup on the nomadik pin controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=vBpq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A number of pinctrl fixes for the v3.7 series:
- duplicate includes, section markup, code mishaps
- erroneous return value in errorpath on the bcm2835 driver
- remove an unused sirf function that was causing build errors
- multiple-platform compilation stubs and a missed code review
comment fixup on the nomadik pin controller"
* tag 'pinctrl-fixes-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: always use the simple irqdomain
pinctrl/nomadik: provide stubs for legacy Nomadik
pinctrl: remove duplicated include from pinctrl-xway.c
pinctrl: sirf: remove sirfsoc_gpio_set_pull function
pinctrl: fix return value in bcm2835_pinctrl_probe()
pinctrl: remove duplicated include from pinctrl-bcm2835.c
pinctrl: bcm2835: Use existing pointer to struct device
pinctrl: samsung: use __devinit section for init code
On some CPU the write to pagemask might complete before the TLB write
instruction reads from the pagemask register.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GPMC code has been converted to a driver by the following commit:
commit da49687397
Author: Afzal Mohammed <afzal@ti.com>
Date: Sun Sep 23 17:28:25 2012 -0600
ARM: OMAP2+: gpmc: minimal driver support
It now requests a clock with con-id "fck" otherwise the probe will fails.
[ 0.342010] omap-gpmc omap-gpmc: error: clk_get
[ 0.346771] omap-gpmc: probe of omap-gpmc failed with error -2
Add the "omap-gmpc" dev-id and fck con-id to the already existing
gmpc-fck dummy clock.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 801475ccb2 ("ARM: OMAP: move
debug_card_init() function") results in the following new sparse
warning:
arch/arm/plat-omap/debug-devices.c:71:12: warning: symbol 'debug_card_init' was not declared. Should it be static?
Fix by implementing Tony's suggestion to add a "sideways include" to the
new location of the debug-devices.h file in arch/arm/mach-omap2/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
R5000 and the Nevada CPUs (RM5230, RM5231, RM5260, RM5261, RM5270 and
RM5271) are basically the same CPU core and all are documented to require
two instructions separating a write to c0_pagemask, c0_entryhi, c0_entrylo0,
c0_entrylo1 or c0_index.
So far we were only providing on cycle before / after a TLBR/TLBWI
for R5000 but 3 cycles before and 1 cycles after for the Nevadas.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The microassembler used in tlbex.c does not notice if a label is redefined
resulting in relocations against such labels silently missrelocated.
The issues exists since commit add6eb04776db4189ea89f596cbcde31b899be9d
[Synthesize TLB exception handlers at runtime.] in 2.6.10 and went unnoticed
for so long because the relocations for the affected branches got computed
to do something *almost* sensible.
The issue affects R4000, R4400, QED/IDT RM5230, RM5231, RM5260, RM5261,
RM5270 and RM5271 processors.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
At some recent point arch/mips/include/asm/delay.h has started being
included into csrc-octeon.c where the __?delay() functions are defined.
This causes a compile failure due to conflicting declarations and
definitions of the functions.
It turns out that the generic definitions in arch/mips/lib/delay.c also
conflict.
Proposed fix: Declare the functions to take unsigned long parameters
just like asm-generic (and x86) does. Update __delay to agree
(__ndelay and __udelay need no change).
Bonus: Get rid of 'inline' from __delay() definition, as it is globally
visible, and the compiler should be making this decision itself (it does
in fact inline the function without being told to).
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4354/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There was a serious disconnect in the logic happening in
sparc_pmu_disable_event() vs. sparc_pmu_enable_event().
Event disable is implemented by programming a NOP event into the PCR.
However, event enable was not reversing this operation. Instead, it
was setting the User/Priv/Hypervisor trace enable bits.
That's not sparc_pmu_enable_event()'s job, that's what
sparc_pmu_enable() and sparc_pmu_disable() do .
The intent of sparc_pmu_enable_event() is clear, since it first clear
out the event type encoding field. So fix this by OR'ing in the event
encoding rather than the trace enable bits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal)
changed the interrupts to allow enabling sparse IRQ, but
accidentally added the omap3 INTC base to the local IRQ.
This causes the following:
twd: can't register interrupt 45 (-22)
twd_local_timer_register failed -22
The right fix is to not add any base, as it is a local
timer. For the OMAP44XX_IRQ_LOCALWDT we had defined earlier
there are no users, so no need to fix that.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This undoes commit 20f4665 "ARM: tegra: remove tegra_timer from
tegra_list_clks" by bringing back the tegra_timer clock. tegra_timer is
indeed a clock (hidden by the PERIPH_CLK macro) which should be added
to the tegra_list_clks.
The above commit caused tegra_init_timer() failing to get the clk
reference.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
[swarren: added the reverted commit's subject to this patch description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The timer variable is renamed to avoid confusion and symbol name clash
with the tegra_timer clock.
Signed-off-by: Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Change the type of variable from "unsigned long" to "u64".
This avoids the overflow while clock rate calculating.
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 9e3c0066 (ARM: dts: imx6q-arm2: add pinctrl for uart and enet)
defines NANDF_CS pins as gpio in 'hog', assuming these two pins are
always used by usdhc3 in gpio mode as card-detection and
write-protection on ARM2 board. But it's not true. These pins are
shared by usdhc3 and gpmi-nand. We should have the pins functional
for gpmi-nand when usdhc3 is disabled.
Move the pins out of 'hog', so that pins only work in gpio mode as CD
and WP when usdhc3 is enabled, and otherwise they are available for
gpmi-nand.
Reported-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Intel PEBS in VT-x context uses the DS address as a guest linear
address, even though its programmed by the host as a host linear
address. This either results in guest memory corruption and or the
hardware faulting and 'crashing' the virtual machine. Therefore we have
to disable PEBS on VT-x enter and re-enable on VT-x exit, enforcing a
strict exclude_guest.
This patch enforces exclude_guest kernel side.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/r/1347569955-54626-3-git-send-email-dsahern@gmail.com
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Use Kbuild infrastructure to handle the asm-generic headers
and remove the wrapper headers that call them.
This only affects headers that do nothing but include the generic
equivalent. It does not touch any header that does a little more.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
