The Phytec phyBOARD Segin is i.MX6 based SBC, available with either an
i.MX6UL or i.MX6ULL SOM and various add-on boards.
The following adds support for the "Full Featured" version of the Segin,
which is provided with the i.MX6UL SOM and the PEB-EVAL-01 evaluation
module.
Its hardware specifications are:
* 512MB DDR3 memory
* 512MB NAND flash
* Dual 10/100 Ethernet
* USB Host and USB OTG
* RS232
* MicroSD external storage
* Audio, RS232, I2C, SPI, CAN headers
* Further I/O options via A/V and Expansion headers
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit d2d0ad2aec ("i2c: imx: use open drain for recovery
GPIO") GPIO lib expects this GPIO to be configured as open drain.
Make sure we define this GPIO as open drain in the device tree.
This gets rid of the following warning:
gpio-81 (scl): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Note that currently the i.MX pinctrl driver does not support
enabling open drain directly, so this patch has no effect in
practice. Open drain is enabled by the fixed pinmux entry.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.
esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6ULL has errata ERR010450, there is I/O timing limitation,
for SDR mode, SD card clock can't exceed 150MHz, for DDR mode,
SD card clock can't exceed 45MHz. This patch change to use the
new compatible "fsl,imx6ull-usdhc" to follow this limitation.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since imx6ulz.dtsi includes imx6ull.dtsi, we only need to fix the compatible
string here to achieve the correct OTP size for both SoCs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was implemented in the driver but not actually defined and
referenced in dts. This makes it always on.
From reference manual in section "10.4.1.4.1 Power Distribution":
"Display domain - The DISPLAY domain contains GIS, CSI, PXP, LCDIF,
PCIe, DCIC, and LDB. It is supplied by internal regulator."
The current pd_pcie is actually only for PCIE_PHY, the PCIE ip block is
actually inside the DISPLAY domain. Handle this by adding the pcie node
in both power domains.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reset signal of the SSD1306 OLED display is actually active-low.
Adapt the DT to reflect the real world.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>,
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
These have been disable since the change to probe Marvell Ethernet
switches as MDIO devices. Remove the properties now that the code to
suppport them will also be removed soon.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Add du node to r8a7744 SoC DT. Boards that want to enable the DU
need to specify the output topology.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the comphy settings for the Ethernet interfaces.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DT description for the Armada 38x common phy.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GTA04 has a w2sg0004 or w2sg0084 gps chip. Not detectable
which one is mounted so use the compatibility entry for w2sg0004
for all which will work for both.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Required for completeness sake to be able to specify
a regulator for devices having a non-optional regulator
property. It corresponds to the "3V3" net in the
schematics.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is one button and a notifier for incoming phone
calls/text messages for which we should wakeup from
suspend.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to use an external link when the file is already here.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the Bananapi M3 and Cubietruck Plus, the DC input jacks are wired to
the ACIN pins, which is represented by the AC power supply. Both boards
have connectors for LiPo batteries, which are represented by the battery
power supply.
The H8 Homlet is a set-top box design. The DC input jack is wired to the
ACIN pins, but there are no battery connectors.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubieboard4 has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 Optimus has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The GMAC (gigabit ethernet controller) supports RGMII to connect to
the ethernet PHY, for gigabit network speeds.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same GMAC found on the A31 SoC.
Add a device node, and an alias for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 has the same DWMAC hardware as on earlier Allwinner SoCs. The
accompanying GMAC clock register has been moved into the "System
Control" area.
Add a clock node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A80 Optimus has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The DC1SW output from the AXP809 is unused. Unused regulators should
still be listed so as to be considered to be fully constrained.
Fixes: aa4a27bc81 ("ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
triggered interrupt.
The msi_ctrl_int will be high for as long as any MSI status bit is set,
thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
IRQ handler to keep getting called, as long as any MSI status bit is set.
A git grep shows that ipq4019 is the only SoC using snps,dw-pcie that has
configured this IRQ incorrectly.
Not having the correct IRQ type defined will cause us to lose interrupts,
which in turn causes timeouts in the PCIe endpoint drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Starting with commit 8947e396a8 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Regarding the 'gpio_keys' device node a dtc reports a couple of
warnings:
Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property
Warning (unit_address_vs_reg): /gpio_keys/button@21: node has
a unit name, but no reg property
The change fixes these issues and adds empty lines between adjacent
children device nodes. The device node itself is renamed by substituting
an underscore by hyphen to follow the standard naming convention
of device tree nodes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a unit address to memory device node, the issue was
reported as a unit_address_vs_reg warning by dtc.
Root device node properties #address-cells and #size-cells were
removed as inherited from lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds a unit address to memory device node, the issue was
reported as a unit_address_vs_reg warning by dtc.
Root device node properties #address-cells and #size-cells were
removed as inherited from lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds description of Sharp LQ035Q7DB03 3.5" 320x240 TFT panel,
which is connected to Phytec phyCORE-LPC3250 board, ARM PrimeCell PL111
LCD controller on NXP LPC3250 SoC gets its configuration appropriately
to support graphics output to the panel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The originally added 'regulators' device node has a number of flaws,
to name a few its children has unit addresses but no reg properties,
the regulators are not captured by a device driver due to a missing
'simple-bus' compatible, the regulator names are selected by killing
either alphabetical order or device node grouping property.
The change removes 'regulators' device node and renames the regulators
and labels.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The fixed voltage regulator on Phytec phyCORE-LPC3250 board, which
supplies SD/MMC card's power, has a constant output voltage level
of either 3.15V or 3.3V, the actual value depends on JP4 position,
the power rail is referenced as VCC_SDIO in the board hardware manual.
Fixes: d06670e962 ("arm: dts: phy3250: add SD fixed regulator")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The originally added ARM PrimeCell PL111 clocks property misses
the required "clcdclk" clock, which is the same as a clock to enable
the LCD controller on NXP LPC3230 and NXP LPC3250 SoCs.
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
ARM PrimeCell PL111 LCD controller is found on On NXP LPC3230
and LPC3250 SoCs variants, the original reference in compatible
property to an older one ARM PrimeCell PL110 is invalid.
Fixes: e04920d9ef ("ARM: LPC32xx: DTS files for device tree conversion")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
After switching to a new interrupt controller scheme by separating SIC1
and SIC2 from MIC interrupt controller just one SoC keypad controller
was not taken into account, fix it now:
WARNING: CPU: 0 PID: 1 at kernel/irq/irqdomain.c:524 irq_domain_associate+0x50/0x1b0
error: hwirq 0x36 is too large for interrupt-controller@40008000
...
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Fixes: 9b8ad3fb81 ("ARM: dts: lpc32xx: reparent SIC1 and SIC2 interrupts from MIC")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
NXP LPC32xx keypad controller requires a clock property to be defined.
The change fixes the driver initialization problem:
lpc32xx_keys 40050000.key: failed to get clock
lpc32xx_keys: probe of 40050000.key failed with error -2
Fixes: 93898eb775 ("arm: dts: lpc32xx: add clock properties to device nodes")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Add support for MYIR Tech MYD-LPC4357 Development Board and
MY-LCD70TP-C 7" TFT LCD module with Innolux AT070TN82 panel.
The board contains quite rich periferals, the list features
NXP LPC4357 SoC, 32 MB SDRAM, 4 MB SPI Flash, audio input/output
interface, LCD panel, micro SD card slot, USB, USB OTG, Ethernet,
2 CAN ports, 4 UARTs, I2C and SPI interfaces routed to external
interface.
More information can be found on http://www.myirtech.com/list.asp?id=422
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix
the following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings
separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[vzapolskiy: fixed commit message to pass checkpatch.pl test]
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The following properties:
- regulator-state-enabled
- regulator-state-disabled
- regulator-state-uv
are not valid ones as per
Documentation/devicetree/bindings/regulator/regulator.txt
Fix it by using the correct properties as per the dt bindings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The following properties:
- regulator-state-enabled
- regulator-state-disabled
- regulator-state-uv
are not valid ones as per
Documentation/devicetree/bindings/regulator/regulator.txt
Fix it by using the correct properties as per the dt bindings.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On rv1108-elgin-r1 board the RK805 VCC5 and VCC6 supplies come from
the BUCK2 regulator at 2.2V, so fix the representation in the
device tree.
While at it, rename it from vdd_cam to vdd_buck2, which is a better
name for the regulator label.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
the missing GPIO labels for RPi 2/3. Additionally it contains
some minor DT fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=kLKJ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=a1d7
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-next-2019-02-01' into devicetree/next
This pull request adds support for the new Raspberry Pi 3 A+ and
the missing GPIO labels for RPi 2/3. Additionally it contains
some minor DT fixes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is no need to specify a pinctrl for the reset GPIO. So we better
remove this avoid a potential conflict between pinctrl and pwrseq
after the pinmux driver has been changed to strict:
pinctrl-bcm2835 20200000.gpio: pin gpio41 already requested by wifi-pwrseq;
cannot claim for pinctrl-bcm2835:499
pinctrl-bcm2835 20200000.gpio: pin-41 (pinctrl-bcm2835:499) status -22
pwrseq_simple: probe of wifi-pwrseq failed with error -22
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The GPIO sysfs is deprecated and disabled in the defconfig files.
So in order to motivate the usage of the new GPIO character device API
add the missing GPIO line names for Raspberry Pi 2 and 3. In the lack
of full schematics i would leave all undocumented pins as unnamed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The RPI 3 B+ provides control to both LEDs (PWR and ACT). So append
the first letter of the LED color (like in the schematics) in order
to clarify this.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
This make the GPIO label for HDMI hotplug more consistent to the other
boards.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the schematics for all RPis with a 40 pin header,
the GPIOs 0 and 1 are labeled as ID_SD and ID_SC. In order to
clarify that is a I2C bus, append the third letter.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Compiling the bcm2835-rpi.dtsi with W=1 leads to the following warning:
Warning (avoid_unnecessary_addr_size): /soc/firmware: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property
Fix this by removing these unnecessary properties.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Compiling the bcm283x DTS with W=1 leads to the following warning:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property,
but no unit name
Fix this by adding the unit address.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi 3 A+ is similar to the Pi 3 B+ but has only 512 MB RAM,
1 USB 2.0 port and no Ethernet.
Compared to the Raspberry Pi 3 B it isn't possible to control BT_ON and
WL_ON separately.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
This patch adds all SPI instances of the STM32F429 SoC.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The GRAFX domain only contains V3D, and this driver should be the only
accessor of V3D (firmware usage gets disabled when V3D is in the DT),
so we can safely make Linux control the GRAFX and GRAFX_V3D power
domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
It was covering part of the PM block's range, up to the WDT regs. To
support the rest of the PM block's functionality, we need the full
register range plus the AXI Async Bridge regs for PM sequencing.
This doesn't convert any of the consumers over to the new binding yet,
since we will need to be careful in coordinating our usage of firmware
services that might power domains on and off versus the bcm2835-pm
driver's access of those same domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
This router has BCM4709C0 SoC, 128 MiB NAND flash (MX30LF1G18AC-TI),
512 MiB memory and 3 x LAN and 1 x WAN ports. WiFi chips are
BCM4366C0 x 2. The router has a small LCD and 3 capactive keys driven by
a PIC microcontroller, which is in turn wired to UART1 of main board.
Signed-off-by: Hao Dong <halbertdong@gmail.com>
[rmilecki: drop chosen { }, fix whitespaces, update commit message]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Couple of simple changes to add dynamic-power-coefficient information
for CPUs on TC2 and fix tuple used for uart and mmci interrupts with
lists.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEunHlEgbzHrJD3ZPhAEG6vDF+4pgFAlxRlvcACgkQAEG6vDF+
4phYSg//eL3ozXhE/L2Fo7Af8Jq36kFz9xlxzDtj6UHZOdvVgsk3hR058ujekwfL
h0pgZ60Naqf6cq4Fg9qviFRKRsSInQ2BBJmJ2FADEZycD14obgIFwqRegGTJ/i08
AYTRm7fm6gCVtbQGXHiSDFFvDZhfKBIG0hJF4A6umK1kWe8Wf77lRetuwGSg1Um7
V187uO7B8b/2AFvtANJhKdN1fHkpJycnXmiLlnS7y4GVxlGd1i84RzhmyF9BUAXi
34s0sZuwm8Tq6+DMP8hh3BBUQeb7Rdk7MvE5clcCAlQCxdKxzv4/kaAghGSSMks6
V3A2WP/zDoC+pGLH4aObLAAxJUag6+0TmX62hXj6qSpnU0xnfXrJgfpMTHQpZ7OB
EWu/3nH8rdEVPO1pxnJN8TRJ5ST7Q89bYoY2oP2XxkAT4GG0vdKcNfGbvM/qwzd7
3pahbE4ewvuUznCvW+KrOTYZBbB4Q7ocjO0UbFclPEfMoQWwV3zbXu5svHp2hC7Y
lMsR3Z7vvgNiKwXfxYpZMn02fCtVdtu7moU9WbP//PUFy8fK6RMYRKG43kNEgVGB
qWHhAZ56yOpQ6QW/2Z6bbQUeUTBeEEoM3KB7S6nc1f6xTJkiDS6dWbhGcMBNexhC
Af44rV+uXUF6S0VdOPmTB4hjWCHg2Pc4dkVYnvVt+SbZYXfu/84=
=Zh3V
-----END PGP SIGNATURE-----
Merge tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv7 Vexpress updates for v5.1
Couple of simple changes to add dynamic-power-coefficient information
for CPUs on TC2 and fix tuple used for uart and mmci interrupts with
lists.
* tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress-v2p-ca15_a7: Add cpu dynamic-power-coefficient information
ARM: dts: vexpress: use list instead of tuple for mmci interrupts
ARM: dts: mps2: use list instead of tuple for uart interrupts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As usual, this is a random assortment of changes:
- ARM PMU is enabled on the A10
- The first usage of the PIO pinbank regulator supplies added,
for the Bananapi
- Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
Ultra, using the serdev bindings
- Video codec added for the A10
- Display pipeline for the A23 added and enabled for the generic Q8
tablets
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEE2nN1m/hhnkhOWjtHOJpUIZwPJDAFAlxMT8UOHHdlbnNAY3Np
ZS5vcmcACgkQOJpUIZwPJDBJwBAA0oV72+9UecBbk+S/HNvSpPS7pL6qEPiMcLtQ
6ucS8zAPvb5oc9TkEdsraddjBlGFppQjPa+fp+9hYMzdSGJflTrTmFdQwet25JT4
WXn6dBpTUcdx5vPaDAq97ynStzl1Nwl9Gc/KBhNtSNlG6Z4Cyz3WplEODMpPsV32
ffoGRVeox3kYJJveawXiUehQwGZfPvnA0y4Njr2M8UprhKLevEazYM5NBfvrwN0Z
3ufHM8cOpfef6lPA9asZ5DK8w5YFENE3a0QcLTY+iBCYxXa1ir8zRg/F9hdUm21H
dGbEdiQOvmSq3JBrZlYwvx1DF+NdTeKIBOsa3SNJccrFzSnZGHz9QJV73mlejNzF
SAptA5vNJa3BtF5g6wKUJjIwFnWSglL7AozVZ/ns+bZi11efpK7iJdzQxyl6cAUS
CcncLt5Ftr1uZZMsiCRDjN1g2wrJSJd6U3zIAYRSMwQIF0j0SNGrtG0kgVo113SQ
Hy4lsdcfIkRMxeahziSBXl54JN/QLaPwlFMfZhFQ//0pC0eGhZrF/BKOSW2w2LQA
PfJBf3h+VUWUSkjOc9EohHhlxFjd7FrHKXLYtMhcynHSFnTKUytDe6O6+hXm/f/e
4sJm5L2mXc1Mk1jK+sAxbChXcgyWByxAVpWKytse8cMyfotrJAssKckMGRDUH1Dn
CocWmC0=
=WU3N
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.1
As usual, this is a random assortment of changes:
- ARM PMU is enabled on the A10
- The first usage of the PIO pinbank regulator supplies added,
for the Bananapi
- Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
Ultra, using the serdev bindings
- Video codec added for the A10
- Display pipeline for the A23 added and enabled for the generic Q8
tablets
* tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i-a23-q8: Set compatible string for LCD panel
ARM: dts: sun8i-q8-common: Enable display pipeline with RGB LCD panel
ARM: dts: sun8i-a23: Add compatible strings to display pipeline device nodes
ARM: dts: sun8i-a33: Move display pipeline nodes to a23/a33 common dtsi
ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address
ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes
ARM: dts: sun4i: Add support for the C1 SRAM region with the SRAM controller
ARM: dts: sunxi: bananapi-m2-plus: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi regulator definitions
ARM: dts: sun8i: r40: Add pinmux setting for CLK_OUT_A
ARM: dts: sun8i: r40: Add pinmux settings for UART3 on PG pingroup
ARM: dts: sun7i: bananapi: Add GPIO banks regulators
ARM: dts: sun4i-a10: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
tree nodes required by the DRM driver.
-----BEGIN PGP SIGNATURE-----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=ezF7
-----END PGP SIGNATURE-----
Merge tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
This updates the Integrator DTS files with the device
tree nodes required by the DRM driver.
* tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Augment panel setting for Integrator/CP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
nodes to the Nomadik NHK8815.
-----BEGIN PGP SIGNATURE-----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=PIyf
-----END PGP SIGNATURE-----
Merge tag 'nomadik-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
This add the new display driver and DRM driver device
nodes to the Nomadik NHK8815.
* tag 'nomadik-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: nomadik: Augment NHK15 panel setting
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
-MPU STM32MP157 platform update:
-Declare DMAs for timers
-Add sleep support for CAN
-Split CAN RAM mapping between the 2 FDCAN instances
-Add support of thermal sensor (DTS)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=660S
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v4.21, round 1
Highlights:
----------
-MPU STM32MP157 platform update:
-Declare DMAs for timers
-Add sleep support for CAN
-Split CAN RAM mapping between the 2 FDCAN instances
-Add support of thermal sensor (DTS)
* tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add thermal sensor support on STM32MP157c
ARM: dts: stm32: add can1 sleep pins muxing on stm32mp157c-ev1 board
ARM: dts: stm32: add can1 sleep pins muxing
ARM: dts: stm32: change CAN RAM mapping on stm32mp157c
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ev1
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ed1
ARM: dts: stm32: Add dmas to timer on stm32mp157c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Convert to new LVDS DT bindings fixing a regression introduced in v4.17
-----BEGIN PGP SIGNATURE-----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=mpfU
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes3-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Third Round of Renesas ARM Based SoC Fixes for v5.0
* Convert to new LVDS DT bindings fixing a regression introduced in v4.17
* tag 'renesas-fixes3-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7743: Convert to new LVDS DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
-----BEGIN PGP SIGNATURE-----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=4km1
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Device tree fixes for omaps for v5.0-rc cycle
This series of dts fixes for omap devices fixes several device specific
regressions:
- The onenand timings for n950/n9 have been wrong for a while since
we moved to dts based timings
- A typo for the cpcap pmic is now producing erors during boot as the
level should be 0 for unconfigurable triggering instead of 1
- Changes for ti-sysc for omap5 left uart3 with debug flags that should
not be set
- Fix a new dtc warning started showing up for omap3-gta04 grap_port
- With the generic MMC card detection code we need to fix the gpio
in dts for n900 and am335x-shc
* tag 'omap-for-v5.0/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: dts: Remove unnecessary idle flags for omap5 uart3
ARM: dts: omap4-droid4: Fix typo in cpcap IRQ flags
ARM: OMAP: dts: N950/N9: fix onenand timings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes a long standing typo in device-tree for DA850 in interrupt
number for timer. It did not affect us so far because we use non-DT
timer driver within mach-davinci. This was caught while migrating to
clocksource driver.
* tag 'davinci-fixes-for-v5.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: fix interrupt numbers for clocksource
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcO/B7AAoJEFBXWFqHsHzOsl4IAL1ubDbUA4T+mbL5joEdmZYZ
iOBVLq5L22uyqUU0i3qSoRi0Tym0ZKXJvP1XdNTlK4fJgabTlvJFlIssBM1FhUMk
pmIDrlCZeoMY1iIJ2OHQ9On9njRA/B+ClZFzFAPR/8iLMC70RB5NMKa8uXYxSQ21
EGjIlNsITD4F/IGt9eqdgt5fnfewgbnumxehvbcYPdreXVRuAyWXlPtc17mI+uof
DmnfANdDZ/VREGJwekQIu2D/VRo6jfC5jc24ixX4Fp5kPZ0CGmXxRzQmTVcm9QQ4
3jRMKf2PXlvW5vcqXLMoGJljVbeYITrF7ycswHge0LPs37ghjW+crAv5TzN6Agg=
=HZIA
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.0:
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
* tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the uart1 node such that the clock will be enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the lpc_ctrl node in the quanta-q71l dts such that the LPC_CLK is
enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added uart2 and uart3 in Facebook Tiogapass for routing serial input
from Host to BMC for SoL via LPC.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added lpc control for enabling lpc clock and lpc snoop devices to
Facebook Tiogapass device tree.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add reset property for dma, can and sdram on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Commit 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") moved some omap4 timers to probe with ti-sysc
interconnect target module. Turns out this broke pwm-omap-dmtimer
for reparenting of the timer clock.
With ti-sysc, we can now configure the clock sources in the dts with
assigned-clocks and assigned-clock-parents.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A CPUfreq driver, like the ARM big.LITTLE driver used on the TC2 board,
which provide the Energy Model with power cost information via the
PM_OPP of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The compatible string for the LCD panel used for the Q8 tablets are just
a placeholder that was shown to be compatible with the actual panels
found on these devices. The real panels do not have any identifiable
markings and vary between production runs.
The compatibe string previously used had a pixel clock that could not
be accurately reproduced on Allwinner hardware, and discussions on
whether a margin should be added to the display drivers and how large
a margin was acceptable had stalled.
Now that we have a panel model that is actually used with Allwinner
hardware, has the same dimensions, and the timings have been shown to
work with the nameless panels, we can use that one instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A13 Q8 tablet, following the A13 reference tablet design, has the
system's fixed 3.3V rail feed the VCC supply of the LCD panel.
Additional voltage rails used by the panel are generated using a
regulator fed from the unregulated IPSOUT output of the PMIC. The latter
is unrepresentable in the device tree. Both are controlled with MOSFETs
by the enable GPIO added in the previous patch. The actual enable or
reset pin for the panel is tied directly to LCD-VCC after the MOSFET.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the AXP209 GPIOs, we can toggle the LCD panel enable
line. Add the GPIO phandle to the panel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The panel backlight and enable GPIO comments were incorrectly placed
in the input port, while it should have been in the panel node itself.
Move them to the correct position.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the GPIOs on the AXP209, we can control the LCD
backlight with them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mmc.txt didn't explicitly say disable-wp is for SD card slot
only, but that is what it was designed for in the first place.
Remove all disable-wp from emmc or sdio controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The change removes redundant #address-cells and #size-cells properties from
gpio-keys-polled compatible device nodes found in lpc4357-ea4357-devkit and
lpc4350-hitex-eval board DTS files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Commit 225da7e65a ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7c ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Q8 tablets follow the A23/A33 tablet reference design, and normally
use a "generic" 800x480 LCD panel. The actual panel may vary between
production runs, and there are no visible markings denoting its model.
This patch uses a panel that has the same dimensions and timings that
are close to what was provided in the vendor fex files.
Since there are also A33 Q8 tablets with 1024x600 panels, this patch
only sets the compatible string for A23 Q8 tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Q8 design for A23/A33 tablets have an 18-bit RGB LCD panel connected
to the LCD interface on the SoC, the DC1SW output on the PMIC providing
power for the LCD, and PH7 toggling the reset pin for the panel.
This patch adds a device node for the panel, describing the above, and
enables the display pipeline.
The actual model or compatible string for the panel should be added in
the tablet device tree file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that the compatible strings for the display pipeline on the A23 have
been added to the bindings, add the corresponding compatibles to the
device nodes already in the A23/A33 shared dtsi.
While the A23 has the TCON ch1 clock defined in the CCU, and the channel
1 registers are available, it does not have any means to use channel 1
due to a lack of downstream encoders, and the enable bit for channel 1 is
hard-wired to 0 (off). Hence the ch1 clock is left out.
As the MIPI DSI output device is not officially documented, and there
are no reference devices to test it, it is not covered by this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The display pipeline has the same structure, resources and connections
on both the A23 and A33. The differences include:
- compatible strings
- extra clock, reset control, and IO region for SAT in the backend
only found on the A33
- missing ch1 clock for the TCON
However, while the A23 has the TCON ch1 clock defined in the CCU, and
the channel 1 registers are available, it does not have any means to
use channel 1 due to a lack of downstream encoders, and the enable bit
for channel 1 is hard-wired to 0 (off).
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
Fixes: d7b843df13 ("ARM: dts: sun8i: add NAND controller node for A23/A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is an ARM + FPGA instrumentation board used at telescopes in
Antarctica, Chile, and Canada:
https://pole.uchicago.edu/https://arxiv.org/abs/1608.03025https://chime-experiment.ca/
With these commits and a suitable userspace, we can boot the board, load
a FPGA bitstream, and communicate with the RTL design. Most of the board's
telemetry sensors (temperatures, voltages) are functional but detailed
testing is to follow.
We are weaning ourselves off TI's "official" kernel for this SOC, which
has been stuck at 2.6.37 and is not really fit for use. To anyone at TI:
despite good silicon and some dedicated support enginers, your
open-source software strategy for these parts has not worked well.
Please get in touch with me if you'd like to have a constructive
discussion about ways to improve it.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: dropped fpga@1 as linux,spidev is still undocumented]
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO3/4 and MCSPI2/3/4 are now present. Lightly tested on am3874
platform.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: split to apply hwmod and dts changes separately]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ethernet works in kernel only if we use some binary u-boot from the
past which have support for KS8851.
The u-boot sources are not available for this mysterious u-boot image
people tends to hold on... Mainline u-bott does not have ethernet support
for sdp4430 and if we use that the ethernet is not working.
After some debugging I have managed to get the ethernet working with
mainline u-boot while not breaking the networking with the case when we
boot with the mysterious binary u-boot.
Basically we were missing bunch of pinmux settings and the 'magic'
gpio_138 handling in kernel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the legacy "linux,wakeup" boolean property is already replaced
with "wakeup-source". However few occurrences of old property has popped
up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit aeda5003d0 ("Input: matrix_keypad - change
name of wakeup property to "wakeup-source"")
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the unnecessary properties #address-cells and #size-cells
of node pinmux as there are no child-nodes with property reg.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it. Code was tested on the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.
Drop the A31 fallback compatible.
Fixes: f89120b6f5 ("ARM: dts: sun8i: Add the H3/H5 CSI controller")
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of
IRQ_TYPE_NONE") started warning about incorrect dts usage for irqs.
ARM GIC only supports active-high interrupts for SPI (Shared Peripheral
Interrupts), and the Palmas PMIC by default is active-low.
Palmas PMIC allows changing the interrupt polarity using register
PALMAS_POLARITY_CTRL_INT_POLARITY, but configuring sys_nirq1 with
a pull-down and setting PALMAS_POLARITY_CTRL_INT_POLARITY made the
Palmas RTC interrupts stop working. This can be easily tested with
kernel tools rtctest.c.
Turns out the SoC inverts the sys_nirq pins for GIC as they do not go
through a peripheral device but go directly to the MPUSS wakeupgen.
I've verified this by muxing the interrupt line temporarily to gpio_wk16
instead of sys_nirq1. with a gpio, the interrupt works fine both
active-low and active-high with the SoC internal pull configured and
palmas polarity configured. But as sys_nirq1, the interrupt only works
when configured ACTIVE_LOW for palmas, and ACTIVE_HIGH for GIC.
Note that there was a similar issue earlier with tegra114 and palmas
interrupt polarity that got fixed by commit df545d1cd0 ("mfd: palmas:
Provide irq flags through DT/platform data"). However, the difference
between omap5 and tegra114 is that tegra inverts the palmas interrupt
twice, once when entering tegra PMC, and again when exiting tegra PMC
to GIC.
Let's fix the issue by adding a custom wakeupgen_irq_set_type() for
wakeupgen and invert any interrupts with wrong polarity. Let's also
warn about any non-sysnirq pins using wrong polarity. Note that we
also need to update the dts for the level as IRQ_TYPE_NONE never
has irq_set_type() called, and let's add some comments and use proper
pin nameing to avoid more confusion later on.
Cc: Belisko Marek <marek.belisko@gmail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
cd pin on mmc1 is GPIO_ACTIVE_LOW not GPIO_ACTIVE_HIGH
Fixes: e63201f194 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We're currently getting a warning with make dtbs:
arch/arm/boot/dts/omap3-gta04.dtsi:720.7-727.4: Warning (graph_port):
/ocp@68000000/dss@48050000/encoder@48050c0 0/port: graph node unit
address error, expected "0"
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wrong polarity of card detect GPIO pin leads to the system not
booting from external mmc, if the back cover of N900 is closed.
When the cover is open the system boots fine.
This wasn't noticed before, because of a bug, which was fixed
by commit e63201f19 (mmc: omap_hsmmc: Delete platform data GPIO
CD and WP).
Kernels up to 4.19 ignored the card detect GPIO from DT.
Fixes: e63201f194 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enable HDMI output on sun8i-h3-nanopi-m1-plus.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for Renesas RZ/A2M evaluation board.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic support for the RZ/A2 (R7S9210) SoC.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41f ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch is to add external trigger stamp fifo support
for 1588 timer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the device tree bindings for USB OTG support. Driver was tested
using on a LG Nexus 5 (hammerhead) phone. This patch is based on work
from Jonathan Marek and from the other msm8974 devices.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the gpio-ranges property to pm8941_gpios so that the GPIO
pins are initialized by the GPIO framework and not pinctrl. This fixes
a circular dependency so GPIO hogging can be used on this board.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds WiFi support to the LG Nexus 5 (hammerhead) phone.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: Enabled wlan_regulator_pin and wlan_sleep_clk_pin]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
All the GSBI blocks are marking their GIC IRQ lines as
"IRQ_TYPE_NONE" but there is no such thing: all GIC IRQ
lines have a trigger type.
That yields the following warning from the GIC driver:
WARNING: CPU: 0 PID: 1 at ../drivers/irqchip/irq-gic.c:1016
gic_irq_domain_translate+0xdc/0xe4
(...)
Mark all of these IRQ_TYPE_LEVEL_HIGH as is common so this
warning goes away.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The GSBI module complains:
gsbi 16500000.gsbi: missing mode configuration
gsbi: probe of 16500000.gsbi failed with error -22
gsbi 16600000.gsbi: missing mode configuration
gsbi: probe of 16600000.gsbi failed with error -22
gsbi 19800000.gsbi: GSBI port protocol: 2 crci: 0
So we should mark these GSBIs as "disabled" in the SoC
file by default.
If boards appear that make use of them, we can simply
set status = "ok" in the DTS for them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Vexpress motherboard MMCI requires dedicated interrupts for CMD and PIO,
which obviously should be expressed as a list. Current form uses tuple
and it works fine since interrupt-cells equal to 1.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Reviewed-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
MPS2 UART requires dedicated interrupts for RX, TX and overflow, which
obviously should be expressed as a list. Current form uses tuple and
it has worked so far because NVIC has interrupt-cells equal to 1.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Inspur on5263m5 is an Intel Xeon OCP server that uses the ASPEED
AST2500 BMC.
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
[joel: Rework commit message]
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds nodes for the Video Engine and the associated reserved memory
for the A10. Up to 96 MiB of memory are dedicated to the CMA pool.
The VPU can only map the first 256 MiB of DRAM, so the reserved memory
pool has to be located in that area. Following Allwinner's decision in
downstream software, the last 96 MiB of the first 256 MiB of RAM are
reserved for this purpose.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A10 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on Rev. 1.00 of the R-Car H1 datasheet.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The timer interrupts specified in commit 3652e2741f ("ARM: dts:
da850: Add clocks") are wrong but since the current timer code
hard-codes them, the bug was never spotted.
This patch must go into stable since, once we introduce a proper
clocksource driver, devices with buggy device tree will stop booting.
Fixes: 3652e2741f ("ARM: dts: da850: Add clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Added ADC and other sensor devices present in the Facebook Tiogapass
machine.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the description of the four Keyboard Controller Style (KCS)
IPMI communication channels present in the ASPEED BMC. They are disabled
by default.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Allows the GPIO controller to be used as an interrupt parent.
of_irq_find_parent() skips interrupt controller nodes that do
not have the #interrupt-cells property.
Signed-off-by: Mark Walton <mark.walton@serialtek.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add Delta Electronics power supply DPS-650-AB.
Signed-off-by: Xiaoting Liu <xiaoting.liu@hxt-semitech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Device tree binding of Memory Controller has been changed: GART has been
squashed into the MC, there are a new mandatory clock and #iommu-cells
properties, the compatible has been changed to 'tegra20-mc-gart'.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add reset property for gpio, i2c, sdmmc, nand, qspi, spi, uart, and
watchdog on base socfpga and socfpga_arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This matches licensing used by other BCM53573 files and BCM5301X.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXDjK7AAKCRALBhiOFHI7
1eZfAJ0X/MrjG/MB1NSlJ2kUGmBs5MnnswCdFZpNF4okkjtwyWoCoBsp9X3kUkw=
=vYNz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 5.0
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX6SX has same GPT type as i.MX6DL, in GPT driver, it uses
below TIMER_OF_DECLARE, so the backward compatible should be
"fsl,imx6dl-gpt", correct it.
TIMER_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
rv1108-elgin-r1 board is based on Rockchip RV1108 SoC.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the pin settings for the SPI pins so they can be used across
multiple boards.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pass the 'dma-names' property to the SPI ports so that DMA can
be supported.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the core display subsystem and vop nodes to rk3066.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Define the required properties to enable I2C bus recovery supported by
the I2C subsystem.
This patch adds GPIO based I2C fault injector for Digi Connectcore SOM.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds definitions for ESDHC1 for Digi Connectore SOM & JSK.
This interface can be used to boot a module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In fact, the RTC battery can only be connected outside the module,
so this patch moves the PMIC RTC property and its power from SOM dts
to JSK.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The interrupt controller is located at the physical address 0x10040000.
This patch changes the unit name of the controller to reflect the actual
address.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of the legacy "gpio-key,wakeup" and "enable-sdio-wakeup" boolean
properties are already replaced with "wakeup-source". However few
occurrences of old property has popped up again, probably from the
remnants in downstream trees. Almost all of those were remove couple
of years back.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit 700a38b27e ("Input: gpio_keys - switch to using
generic device properties") and commit 0dbcdc0622 ("mmc: core: enable
support for the standard "wakeup-source" property")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dspi3 is used as slave controller on vf610-bk4, and the default
'#address-cells = <1>;' setting in vfxxx.dtsi causes the following DTC
warning.
DTC arch/arm/boot/dts/vf610-bk4.dtb
../arch/arm/boot/dts/vfxxx.dtsi:550.24-563.6: Warning (spi_bus_bridge): /soc/aips-bus@40080000/spi@400ad000: incorrect #address-cells for SPI bus
also defined at ../arch/arm/boot/dts/vf610-bk4.dts:107.8-119.3
arch/arm/boot/dts/vf610-bk4.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
For spi device used as slave controller, '#address-cells' should be 0.
Let's overwrite the property in vf610-bk4.dts to fix the warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NHK15 panel is specified inside the display controller,
which works for the DPI-type DT parsing the old fbdev code
used, but for the DRM driver it needs to be spawn as its own
device, so we move it out of the display controller.
We also drop the panel timings: this should be determined
by the hardware or a device-specific compatible string, not
by this type of encoding into the device tree. It turns out
that this hardware is strapped to the right configuration
at boot already and we the driver just reads out the
hardware-specified resolution and timings. Drop the
"panel,dpi" compatible string altogether.
Fix a comment error in the DTS file while we're at it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
