The config.speed_hz is just setted at the two lines ahead of it,
obviously we don't need to copy the code to set the config.speed_hz
again. Remove it for a cleanup.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The chip select line was configured as output with the initial value
being active explicitly. It was later deasserted during
spi_bitbang_setup() without any clock activity in between. So it makes
no sense to activate the device at all and the chip select line can
better start non-active.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI FIFO and memory in
place of legacy Tegra APB DMA.
The new driver is selected if legacy driver is not
selected and new DMA driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we're gonna use runtime PM it's a pretty good idea to actually
enable it in probe() and disable it in remove() too, so it
gets used for real. Up until now we only fooled around with the
reference count.
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This ASIC variant has been deleted from the ARM tree, no need
to keep support around.
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ffbbdd2132
"spi: create a message queueing infrastructure"
Accidentally deleted the logic to disable the port
when unused leading to higher power consumption.
Fix this up.
Cc: stable@kernel.org
Cc: Vinit Shenoy <vinit.shenoy@st.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1a77b127ae (OMAP : SPI : use devm_* functions) converted the SPI
device controller state to use devm_kzalloc(). Unfortunately, this
is used against an unbound struct device, which results in the
following when the device is bound to its driver:
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/drivers/base/dd.c:257 driver_probe_device+0x78/0x21c()
Modules linked in:
Backtrace:
[<c0017d0c>] (dump_backtrace+0x0/0x10c) from [<c033e208>] (dump_stack+0x18/0x1c) r7:00000000 r6:c01ff28c r5:c040050c r4:00000101
[<c033e1f0>] (dump_stack+0x0/0x1c) from [<c00337ec>] (warn_slowpath_common+0x58/0x70)
[<c0033794>] (warn_slowpath_common+0x0/0x70) from [<c0033828>] (warn_slowpath_null+0x24/0x2c)
[<c0033804>] (warn_slowpath_null+0x0/0x2c) from [<c01ff28c>] (driver_probe_device+0x78/0x21c)
[<c01ff214>] (driver_probe_device+0x0/0x21c) from [<c01ff49c>] (__driver_attach+0x6c/0x90)
[<c01ff430>] (__driver_attach+0x0/0x90) from [<c01fda70>] (bus_for_each_dev+0x58/0x98)
[<c01fda18>] (bus_for_each_dev+0x0/0x98) from [<c01ff0f4>] (driver_attach+0x20/0x28)
[<c01ff0d4>] (driver_attach+0x0/0x28) from [<c01fe2f4>] (bus_add_driver+0xb4/0x230)
[<c01fe240>] (bus_add_driver+0x0/0x230) from [<c01ffb24>] (driver_register+0xac/0x138)
[<c01ffa78>] (driver_register+0x0/0x138) from [<c0215d4c>] (spi_register_driver+0x4c/0x60)
[<c0215d00>] (spi_register_driver+0x0/0x60) from [<c045414c>] (ks8851_init+0x14/0x1c)
[<c0454138>] (ks8851_init+0x0/0x1c) from [<c0008770>] (do_one_initcall+0x9c/0x164)
[<c00086d4>] (do_one_initcall+0x0/0x164) from [<c0436410>] (kernel_init+0x128/0x210)
[<c04362e8>] (kernel_init+0x0/0x210) from [<c0038754>] (do_exit+0x0/0x72c)
---[ end trace 4dcda79f5e89dd84 ]---
ks8851 spi1.0: message enable is 0
ks8851 spi1.0: eth0: revision 0, MAC 08:00:28:01:4d:c6, IRQ 194, has EEPROM
Fix this by partially reverting the original commit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
Bug fixes and new features for SPI device drivers. Also move device
tree support code out of drivers/of and into drivers/spi/spi.c where
it makes more sense.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/Ux1
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI changes from Grant Likely:
"Bug fixes and new features for SPI device drivers. Also move device
tree support code out of drivers/of and into drivers/spi/spi.c where
it makes more sense."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi: By default setup spi_masters with 1 chipselect and dynamics bus number
SPI: PRIMA2: use the newest APIs of PINCTRL to fix compiling errors
spi/spi-fsl-spi: reference correct pdata in fsl_spi_cs_control
spi: refactor spi-coldfire-qspi to use SPI queue framework.
spi/omap2-mcspi: convert to the pump message infrastructure
spi/rspi: add dmaengine support
spi/topcliff: use correct __devexit_p annotation
spi: Dont call prepare/unprepare transfer if not populated
spi/ep93xx: clean probe/remove routines
spi/devicetree: Move devicetree support code into spi directory
spi: use module_pci_driver
spi/omap2-mcspi: Trivial optimisation
spi: omap2-mcspi: add support for pm_runtime autosuspend
spi/omap: Remove bus_num usage for instance index
OMAP : SPI : use devm_* functions
spi: omap2-mcspi: convert to module_platform_driver
spi: omap2-mcspi: make it behave as a module
The modalias attribute of spi devices doesn't have the "spi:" prefix
that is used in the UEVENT and in spi device drivers. This patch adds
the prefix so the modprobe can correctly match modules to devices.
Reported-by: David Daney <david.daney@cavium.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Trivial simplification. Instead of requiring spi master drivers to
always set the bus number (even when a dynamic number is desired),
this patch modifies spi_alloc_master() to initialize num_chipselect to
1 (because there will always be at least one CS) and bus_num to -1 for
dynamic allocation. This simplifies the code needed to be written for
drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix the compiling errors:
drivers/spi/spi-sirf.c: In function 'spi_sirfsoc_probe':
drivers/spi/spi-sirf.c:563: error: implicit declaration of function 'pinmux_get'
drivers/spi/spi-sirf.c:563: warning: assignment makes pointer from integer without a cast
drivers/spi/spi-sirf.c:568: error: implicit declaration of function 'pinmux_enable'
drivers/spi/spi-sirf.c:602: error: implicit declaration of function 'pinmux_disable'
drivers/spi/spi-sirf.c:603: error: implicit declaration of function 'pinmux_put'
make[3]: *** [drivers/spi/spi-sirf.o] Error 1
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed spi device initialization of dev.parent pointer
to be the master's device pointer instead of his parent.
This introduced a bug in spi-fsl-spi, since its usage of spi device
pointer was not updated accordingly. This was later fixed by commit
5039a86, "spi/mpc83xx: fix NULL pdata dereference bug", but it missed
another spot on fsl_spi_cs_control function where we also need to update
usage of spi device pointer. This change address that.
Cc: stable@vger.kernel.org
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the new SPI queue framework; remove use of workqueue, replace
mcfqspi_transfer with mcfqspi_transfer_one_message, add
mcfqspi_prepare_transfer_hw and mcfqspi_unprepare_transfer_hw, update power
management routines.
Signed-off-by: Steven King <sfking@fdwdc.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the OMAP SPI driver to use the SPI infrastructure
pump message queue.Also fixes the below warning.
master is unqueued, this is deprecated
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds dmaengine supporting using sh_dma driver. The module
receives data by DMAC, it also needs TX DMAC to generate SPI's clocks.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
__devexit functions are discarded when CONFIG_HOTPLUG
is not set, so the symbol needs to be referenced carefully.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the prepare/unprepare transfer are called unconditionally.
The assumption is that every driver using the spi core queue infrastructure
has to populate the prepare and unprepare functions. This encourages
drivers to populate empty functions to prevent crashing.
This patch prevents the call to prepare/unprepare if not populated.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[grant.likely: fix whitespace defect]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use devm_* functions for managing devres resources.
Also use local variable irq and remove irq variable from
struct ep93xx_spi, as it is needed only in probe routine.
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Hannu Heikkinen <hannuxx@iki.fi>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch ensures that the last bit of a transfer gets correctly
flushed out of the register.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This condition is used to determine 8 bits or 16 and 32 bits transfer.
Obviously it is reversed.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since the member was dropped from the common Blackfin header, we need
to stop using it in the SPORT driver too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
No other SPI controller has this field, and SPI clients should be setting
this up in their own drivers. So drop it from the Blackfin controller to
keep people from using it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each transfer may have its own bits per word.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This controller is only for blackfin 5xx soc, so rename it to BFIN5XX
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, if we request for frequency greater than maximum possible, spi driver
returns error.
For example, if the spi block src frequency is 333/4 MHz, i.e. 83.33.. MHz,
maximum frequency programmable would be src/2. Which would come around 41.6...
It is difficult to pass frequency in these figures. We normally try to program
in round figures, like 42 MHz and it should get programmed to <=
requested_frequency, i.e. 41.6...
For this to happen, we must not return error even if requested freq is higher
than max possible. But should program it to max possible.
Reported-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We were not properly advertising the MODE bits supported by this driver, fix
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We do not need to use a flag to indicate if the master driver is stopping
it is sufficient to perform spi master unregistering in the platform
driver's remove function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the bcm63xx SPI driver to use the SPI infrastructure
pump message queue. Since we were previously sleeping in the SPI
driver's transfer() function (which is not allowed) this is now fixed as well.
To complete that conversion a certain number of changes have been made:
- the transfer len is split into multiple hardware transfers in case its
size is bigger than the hardware FIFO size
- the FIFO refill is no longer done in the interrupt context, which was a
bad idea leading to quick interrupt handler re-entrancy
Tested-by: Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A new enum indicating the dma channel direction was introduced by:
commit 49920bc669
dmaengine: add new enum dma_transfer_direction
The following commit changed spi-ep93xx to use the new enum:
commit a485df4b44
spi, serial: move to dma_transfer_direction
In doing so a sparse warning was introduced:
warning: mixing different enum types
int enum dma_data_direction versus
int enum dma_transfer_direction
This is produced because the 'dir' passed in ep93xx_spi_dma_prepare
is an enum dma_data_direction and is being used to set the
dma_slave_config 'direction' which is now an enum dma_transfer_direction.
Fix this by converting spi-ep93xx to use the new enum type in all
places.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calculate_effective_freq() was still not optimized and there were cases when it
returned without error and with values of cpsr and scr as zero.
Also, the variable named found is not used well.
This patch targets to optimize and correct this routine. Tested for SPEAr.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Vinit Kamalaksha Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Newer SoCs from the S3C24XX line, namely S3C2416/2443/2450 contain
hsspi-controllers compatible with the s3c64xx type.
The previous patches enabled platform support for it, so make the
driver also usable for the S3C24xx architecture.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
pl022 ssp controller supports word lengths from 4 to 16 (or 32) bits.
Currently implemented checks were incorrect. It has following check
if (pl022->vendor->max_bpw >= 32)
which must be checking for <=.
Also error print message is incorrect, that prints "range is from 1 to
16".
Fix both these issues.
Signed-off-by: Vinit Shenoy <vinit.shenoy@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pull ARM fixes from Russell King:
"Nothing too disasterous, the biggest thing being the removal of the
regulator support for vcore in the AMBA driver; only one SoC was using
this and it got broken during the last merge window, which then
started causing problems for other people. Mutual agreement was
reached for it to be removed."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7386/1: jump_label: fixup for rename to static_key
ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
ARM: 7383/1: nommu: populate vectors page from paging_init
ARM: 7381/1: nommu: fix typo in mm/Kconfig
ARM: 7380/1: DT: do not add a zero-sized memory property
ARM: 7379/1: DT: fix atags_to_fdt() second call site
ARM: 7366/3: amba: Remove AMBA level regulator support
ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented
Miscellaneous driver bug fixes. No major changes in this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tw/j
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI bug fixes from Grant Likely:
"Miscellaneous driver bug fixes. No major changes in this branch."
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi/imx: prevent NULL pointer dereference in spi_imx_probe()
spi/imx: mark base member in spi_imx_data as __iomem
spi/mpc83xx: fix NULL pdata dereference bug
spi/davinci: Fix DMA API usage in davinci
spi/pL022: include types.h to remove compilation warnings
The SPI device tree support code isn't shared by any other subsystem. It can
be moved into the core drivers/spi directory and the exported symbol can be
removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
The AMBA bus regulator support is being used to model on/off switches
for power domains which isn't terribly idiomatic for modern kernels with
the generic power domain code and creates integration problems on platforms
which don't use regulators for their power domains as it's hard to tell
the difference between a regulator that is needed but failed to be provided
and one that isn't supposed to be there (though DT does make that easier).
Platforms that wish to use the regulator API to manage their power domains
can indirect via the power domain interface.
This feature is only used with the vape supply of the db8500 PRCMU
driver which supplies the UARTs and MMC controllers, none of which have
support for managing vcore at runtime in mainline (only pl022 SPI
controller does). Update that supply to have an always_on constraint
until the power domain support for the system is updated so that it is
enabled for these users, this is likely to have no impact on practical
systems as probably at least one of these devices will be active and
cause AMBA to hold the supply on anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When no platform_data is present and either 'spi-num-chipselects' is
not defined in the DT or 'cs-gpios' has less entries than
'spi-num-chipselects' specifies, the NULL platform_data pointer is
being dereferenced.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts the drivers in drivers/spi/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Trivial optimisation of tmp variable by directly writing the value
to the register.
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Adds support for configuring the omap2-mcspi driver use autosuspend for
runtime power management. This can reduce the latency in starting an
spi transfer by not suspending the device immediately following
completion of a transfer. If another transfer then takes place before
the autosuspend timeout (2 secs), the call to resume the device can
return immediately saving some save/ restore cycles.
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
