intel_dp_set_infoframes() call in intel_ddi_post_disable_dp() will
take care to disable all enabled infoframes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514232247.144542-4-jose.souza@intel.com
An async-put on an encoder specific power domain (for instance the AUX
PW domain) may be pending when removing the encoder. Make sure any such
async-puts are complete while the corresponding encoder is still in place
since at least AUX power wells require this to do a power well->PHY
lookup.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526143729.2563672-1-imre.deak@intel.com
On ADL-P, it's possible to enable the stream splitter on pipe B in
addition to pipe A.
Bspec: 50174
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526082903.26395-1-jani.nikula@intel.com
On ADL_P besides programming the PLL accordingly the DP/HDMI link rate
should be also programmed to the DDI_BUF_CTL register, do that.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-16-lucas.demarchi@intel.com
Define and use DP voltage swing and pre-emphasis translation tables
for ADL-P.
v2:
- Update according to recent bspec updates; there are now separate
tables for RBR/HBR and HBR2/HBR3. (Anusha)
BSpec: 54956
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-14-lucas.demarchi@intel.com
ADL-P have basically the same TC connection and disconnection
sequences as ICL and TGL, the major difference is the new registers.
So here adding functions without the icl prefix in the name and
making the new functions call the platform specific function to access
the correct register.
v2:
- Retain DDI TC PHY ownership flag during modesetting.
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-6-lucas.demarchi@intel.com
Disable loadgen sharing for DP link rate 1.62 GHz and HDMI 5.94 GHz.
For all other modes, we can enable loadgen sharing feature.
BSpec: 55359
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-13-matthew.d.roper@intel.com
The DDI naming template for display version 12 went A-C, TC1-TC6. With
XE_LPD, that naming scheme for DDI's has now changed to A-E, TC1-TC4.
The XE_LPD design keeps the register offsets and bitfields relating to
the TC outputs in the same location they were previously. The new "D"
and "E" outputs now take the locations that were previously used by TC5
and TC6 outputs, or what we would have considered to be outputs "H" and
"I" under the legacy lettering scheme.
For the most part everything will just work as long as we initialize the
output with the proper 'enum port' value. However we do need to take
care to pick the correct AUX channel when parsing the VBT (e.g., a
reference to 'AUX D' is actually asking us to use the 8th aux channel,
not the fourth). We should also make sure that our encoders and aux
channels are named appropriately so that it's easier to correlate driver
debug messages with the bspec instructions.
v2:
- Update handling of TGL_TRANS_CLK_SEL_PORT. (Jose)
v3:
- Add hpd_pin to handle outputs D and E (Jose)
- Fixed conversion of BIOS port to aux ch for TC ports (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-2-matthew.d.roper@intel.com
So far if we had a mismatch between the state asked and what was
programmed in hardware for PSR, this mismatch would go unnoticed.
So here adding the PSR to the hardware configuration readout,
EDP_PSR_CTL and EDP_PSR2_CTL can't be directly read because its state
flips due to other factors like frontbuffer modifications and CRC.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210418002126.87882-1-jose.souza@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Just let bxt/glk fall back to intel_hpd_pin_default() instead
of using skl_hpd_pin() or cnl_hpd_pin(). Doesn't really matter
since both functions will end up returning the correct hpd pin
anyway, but I find it a bit less confusing when bxt/glk are
fully separated from the logic for the other platforms.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210412054607.18133-5-ville.syrjala@linux.intel.com
Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the
display code, we should also kill off our use of the IS_GEN9_* macros
too. We'll do the conversion manually this time instead of using
Coccinelle since the most logical substitution can depend heavily on the
code context, and sometimes we can keep the code simpler if we make
additional adjustments such as swapping the order of if/else arms.
v2:
- Restore a lost negation in intel_pll_is_valid().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com
(cherry picked from commit 70bfb30743)
[Jani: cherry picked to topic branch to reduce conflicts]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
Add intel_bios_encoder_data pointer to encoder, and use it for hdmi and
dp iboost. For starters, we only set the encoder->devdata for DDI
encoders, i.e. we can only use it for data that is used by DDI encoders.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4bc49244ce68e136e5b21db4c4e6554bec9ac0fb.1615998927.git.jani.nikula@intel.com
Stop caching the information in ddi_port_info. We're phasing out
ddi_port_info usage completely, and prefer using the VBT child device
information directly using the provided helpers.
v2:
- Remove supports_typec_usb & supports_tbt from ddi_vbt_port_info (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b04bd183e7554aeb4bc3962af90d63171aa32fc2.1615998927.git.jani.nikula@intel.com
Start using struct intel_bios_encoder_data directly. We'll start
sanitizing the child device data directly as well, instead of the cached
data in ddi_port_info[]. The one downside here is having to store a
non-const pointer back to intel_bios_encoder_data.
Eventually we'll be able to have a direct pointer from encoder to
intel_bios_encoder_data, removing the need to go through the
ddi_port_info[] array altogether. And we'll be able to remove all the
cached data in ddi_port_info[].
v2:
- Remove supports_dp and supports_edp from ddi_port_info too
- Add devdata != NULL check in intel_bios_is_port_edp()
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> # v1
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/061df32a012ff640060920fcd730fb23f8717ee8.1615998927.git.jani.nikula@intel.com
Let's check that we actually found the PLL before doing the
port_clock readout, just in case the hardware was severly
misprogrammed by the previous guy. Not sure the hw would
even survive such misprogramming without hanging but no
real harm in checking anyway.
Cc: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210310194351.6233-1-ville.syrjala@linux.intel.com
Reviewed-by: Karthik B S <karthik.b.s@intel.com>
Now that all the encoder clock stuff is uniformly abstracted
for all hsw+ platforms, let's extend icl_sanitize_encoder_pll_mapping()
to cover all of them.
Not sure there is a particular benefit in doing so, but less special
cases always makes me happy.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-7-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Support reading out the current state of the DDI clock.
Not sure we really want this. Seems a bit excessive just to
restore the debug print to icl_sanitize_encoder_pll_mapping()?
But maybe there's more use for it?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Move the *_get_ddi_pll() stuff into the encodet->get_config() hook.
There it neatly sits next to the matching .{enable,disable}_clock()
functions.
In order to avoid excessive boilerplate I changed the behaviour
such that all platforms now do the readout via
crtc_state->port_dpll[].
ICL+ TC is still a bit special due to TBTPLL not having a functional
.get_freq(). Should probably change that by adopting the LCPLL
approach, but that would require a fairly substantial rework of the
DPLL ID handling. So leave it for later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-5-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
On platforms/outputs without a working frame counter we rely
on the vblank code to cook up the frame counter from the timestamps.
That requires that vblank support is enabled. Thus we need to
move the pipe enable/disable tracepoints to the other side
of the drm_vblank_{on,off}() calls. There shouldn't really be
much happening between these old and new call sites so the
tracepoints should still provide reasonable data.
The alternative would be to give up on having the frame counter
values in the trace which would render the tracepoints more or
less pointless.
v2: Missed one case in intel_ddi_post_disable()
Drop the now useless i915_trace.h includes
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-2-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Add splitter configuration to crtc state, and read it where
supported. Also add splitter state dumping. The stream splitter will be
required for eDP MSO.
v4:
- Catch invalid splitter configuration (Uma)
v3:
- Convert segment timings to full panel timings.
- Refer to splitter instead of mso in crtc state.
- Dump splitter state.
v2: Add warning for mso being enabled on pipes other than A.
Cc: Nischal Varide <nischal.varide@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/95cbe1c9d45edf3e3ec252e49fb49055def98155.1614682842.git.jani.nikula@intel.com
Instead of every new platform having yet another masive
copy of the whole PLL sanitation code, let's just reuse the
.disable_clock() hook for this purpose. We do need to plug
this into the ICL+ DSI code for that, but fortunately it
already has a suitable function we can use.
We do lose the debug message though on account of not bothering
to check if the clock is actually enabled or not before turning
it off. We could introduce yet another vfunc to query the current
state, but not sure it's worth the hassle?
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-14-ville.syrjala@linux.intel.com
Since .{enable,disable}_clock() are already vfuncs it's a bit silly to
have if-ladders inside them. Just provide specialized version for adl-s
and rkl so we don't need any of that.
v2: s/dev_priv/i915/ (Lucas)
Fix typos in platform names (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-13-ville.syrjala@linux.intel.com
The other DDI .enable_clock() functions are trying to protect us
against pll==NULL. A bit tempted to throw out all the WARNs as
just unnecessary noise, but I guess they might have some use
when poking around the shared_dpll code (not sure it wouldn't
oops elsewhere though). So let's unify it all and sprinkle in
the missing WARNs for icl/dg1.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-11-ville.syrjala@linux.intel.com
The current code attempts to protect the RMWs into global
clock routing registers with a mutex, but forgets to do so
in a few places. Let's remedy that.
Note that at the moment we serialize all modesets onto single
wq, so this shouldn't actually matter. But maybe one day we
wish to attempt parallel modesets again...
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-10-ville.syrjala@linux.intel.com
For ICL+ we have several styles of clock routing for DDIs:
1) TC DDI + TC PHY
-> needs DDI_CLK_SEL==MG/TBT part form intel_ddi_clk_{select,disable}()
and ICL_DPCLKA_CFGCR0_TC_CLK_OFF part form icl_{map,unmap}_plls_to_ports()
2) ICL/TGL combo DDI + combo PHY
-> just need the stuff from icl_{map,unmap}_plls_to_ports()
3) JSL/EHL TC DDI + combo PHY
-> needs DDI_CLK_SEL==MG part from intel_ddi_clk_{select,disable}() and
the full combo style clock selection from icl_{map,unmap}_plls_to_ports()
4) ADLS/RKL
-> these use both TC and combo DDIs with combo PHYs, however they
always use the full combo style clock selection as per
icl_{map,unmap}_plls_to_ports() and do not use DDI_CLK_SEL at all,
thus get treated the same as 2)
We extract all that from the current mess in the following way:
1) icl_ddi_tc_{enable,disable}_clock()
2) icl_ddi_combo_{enable,disable}_clock()
3) jsl_ddi_tc_{enable,disable}_clock()
4) for now we reuse icl_ddi_combo_{enable,disable}_clock() here
v2: s/dev_priv/i915/ (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-8-ville.syrjala@linux.intel.com
Yank out the HSW/BDW code from intel_ddi_clk_{select,disable}()
and put it into the new encoder .{enable,disable}_clock() vfuncs.
v2: s/dev_priv/i915/ (Lucas)
v3: Deal with FDI
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-4-ville.syrjala@linux.intel.com
The current code dealing with the clock routing for DDI encoders
is a maintenance nightmare. Let's start cleaning it up by allowing
the encoder to provide vfuncs for enablign/disabling the clock.
We leave them initially unimplemented, falling back to the old
if-else approach.
v2: Convert the FDI enable sequence
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-3-ville.syrjala@linux.intel.com
We want to put all DDI clock routing code into one place.
Unify the FDI enable sequence to use the standard function
instead of hand rolling its own. The disable sequence already
uses the normal thing.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-2-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Next, let's start introducing the HPD pin mappings for Intel's new gen9_bc
platform in order to make hotplugging display connectors work. Since
gen9_bc is just a TGP PCH along with a CML CPU, except with the same HPD
mappings as ICL, we simply add a skl_hpd_pin function that is shared
between gen9 and gen9_bc which handles both the traditional gen9 HPD pin
mappings and the Icelake HPD pin mappings that gen9_bc uses.
Changes since v4:
* Split this into its own commit
* Introduce skl_hpd_pin() like vsyrjala suggested and use that instead of
sticking our HPD pin mappings in TGP code
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
[originally from Tejas's work]
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209212832.1401815-4-lyude@redhat.com
Lane Reversal is required for some of the DDI ports. This information
is populated in VBT and driver should read the same and set the
polarity while enabling the port. This patch handles the same.
It helps fix a display blankout issue on DP ports on certain
platforms.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210211114209.23866-1-uma.shankar@intel.com
This moves the code from various places and consolidates it
into one new file.
v2:
- rename skl_program_plane -> skl_program_plane_scaler (Ville)
- also move skl_pfit_enable, and consequently make some skl_scaler_*
functions static to skl_scaler.c (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2fa703ffc7b96a41c392fd5ebbd2e6e4ffb6fb05.1612536383.git.jani.nikula@intel.com
Rework the plane init calls to do the gen test one level higher.
Rework some of the plane helpers so they can live in new file,
there is still some scope to clean up the plane/fb interactions
later.
v2: drop atomic code back, rename file to Ville suggestions,
add header file.
v3: move scaler bits back
v4: drop wrong new includes (Ville)
v5: integrate the ccs gen12 changes
v6: fix unrelated code movement (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Jani: fixed up sparse warnings.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4e88a5c6b9ab3b93cc2b6c7d78c26ae86f6abbd0.1612536383.git.jani.nikula@intel.com
Ville suggested this, these tables are probably better being
standalone.
This fixes up the cnl/bxt interfaces to be like the others,
the intel one I left alone since it has a few extra entrypoints.
v2: add back missing rocketlake bits.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Jani: made some functions static]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/def9eed2581d71863ccdf35f323b525facc2482c.1612467466.git.jani.nikula@intel.com
We shouldn't really trust tc_mode on non-TC PHYs since we never
initialize it explicitly. So let's check for the PHY type first.
Fortunately TC_PORT_TBT_ALT happens to be zero so I don't think
there's an actual bug here, just a possibility for a future one
if someone rearranges the enum values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In thunderbolt mode the PHY is owned by the thunderbolt controller.
We are not supposed to touch it. So skip the vswing programming
as well (we already skipped the other steps not applicable to TBT).
Touching this stuff could supposedly interfere with the PHY
programming done by the thunderbolt controller.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Add changes to configure port clock registers for ADL-S. Combo phy port
clocks are configured by DPCLKA_CFGCR0 and DPCLKA_CFGCR1 registers.
The DDI to internal clock mappings in DPCLKA_CFGCR0 register for ADL-S
translates to
DDI A -> DDIA
DDI B -> USBC1
DDI I -> USBC2
For DPCLKA_CFGCR1
DDI J -> USBC3
DDI K -> USBC4
Bspec: 50287
Bspec: 53812
Bspec: 53723
v2: Replace I915_READ() with intel_de_read().(Jani)
v3:
- Use reg variable to assign ADLS specific registers inorder to replace
branching with intel_de_read/write() calls.(mdroper)
- Reuse icl_get_ddi_pll() for ADLS to fix issue with updating active
dpll on driver load.(aswarup)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125140753.347998-7-aditya.swarup@intel.com
If VRR is enabled, the sink should ignore MSA parameters
and regenerate incoming video stream without depending
on these parameters. Hence set the MSA_TIMING_PAR_IGNORE_EN
bit if VRR is enabled.
Reset this bit on VRR disable.
v2:
* ACtually set the dpcd msa ignore bit (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-13-manasi.d.navare@intel.com
This patch disables the VRR enable and VRR PUSH
bits in the HW during commit modeset disable sequence.
Thsi disable will happen when the port is disabled
or when the userspace sets VRR prop to false and
requests to disable VRR.
v2:
* Use intel_de_rmw (Jani N)
v3:
* Remove rmw (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-12-manasi.d.navare@intel.com
This patch computes the VRR parameters from VRR crtc states
and configures them in VRR registers during CRTC enable in
the modeset enable sequence.
v2:
* Remove initialization to 0 (Jani N)
* Use correct pipe %c (Jani N)
v3:
* Remove debug prints (Ville)
* Use cpu_trans instead of pipe for TRANS_VRR regs (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-10-manasi.d.navare@intel.com
Get rid of the "I like my random new style best" approach and unify
the handling for the DDI buf trans table sanity checks once again.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201207203512.1718-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The MH PHY vswing table does have all the entries these days. Get
rid of the old hacks in the code which claim otherwise.
This hack was totally bogus anyway. The correct way to handle the
lack of those two entries would have been to declare our max
vswing and pre-emph to both be level 2.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Fixes: 9f7ffa2979 ("drm/i915/tc/icl: Update TC vswing tables")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201207203512.1718-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
I accidentally added the compliance test hacks only to
intel_dp_hotplug() which doesn't even get used on any DDI
platform. Put the same crap into intel_ddi_hotplug().
Cc: Imre Deak <imre.deak@intel.com>
Fixes: 193af12cd6 ("drm/i915: Shove the PHY test into the hotplug work")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114205046.8247-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
In a long overdue refactoring, split out all panel sequencer code from
intel_dp.c to new intel_pps.[ch].
The first part is mostly just code movement as-is, without cleanups or
functional changes.
We need to add a vlv_get_dpll() helper to get at the vlv/chv dpll from
pps code.
v2: Rebase.
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/14cc59d5734432ad976cd49ff8efce8fa413e5b2.1610127741.git.jani.nikula@intel.com
hdcp_port_data is specific to a port on which HDCP
encryption is getting enabled, so encapsulate it to
intel_digital_port.
This will be required to enable HDCP 2.2 stream encryption.
v2:
- 's/port_data/hdcp_port_data'. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-12-anshuman.gupta@intel.com
Both HDCP_{1.x,2.x} requires to select/deselect Multistream HDCP bit
in TRANS_DDI_FUNC_CTL in order to enable/disable stream HDCP
encryption over DP MST Transport Link.
HDCP 1.4 stream encryption requires to validate the stream encryption
status in HDCP_STATUS_{TRANSCODER,PORT} register driving that link
in order to enable/disable the stream encryption.
Both of above requirement are same for all Gen with respect to
B.Spec Documentation.
v2:
- Cosmetic changes function name, error msg print and
stream typo fixes. [Uma]
v3:
- uniformity for connector detail in DMESG. [Ram]
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-8-anshuman.gupta@intel.com
Gen12 has H/W delta with respect to HDCP{1.x,2.x} display engine
instances lies in Transcoder instead of DDI as in Gen11.
This requires hdcp driver to use mst_master_transcoder for link
authentication and stream transcoder for stream encryption
separately.
This will be used for both HDCP 1.4 and HDCP 2.2 over DP MST
on Gen12.
Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111081120.28417-6-anshuman.gupta@intel.com
DG1's vswing tables are the same for eDP and HDMI but have slight
differences from ICL/TGL for DP.
v2:
- Use a "_hbr2_hbr3" suffix on the table name to make it more clear
that the same table is used for both HBR2 and HBR3 link rates.
(Swathi)
Bspec: 49291
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108222528.1954514-1-matthew.d.roper@intel.com
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
There was some misinterpretation of specification, when DDIX_USED is
set, the next bit means 0 for DP and 1 for HDMI.
Anyways this misinterpretation is not causing any issues, this change
is just to comply with specification.
Also as for us it do not matters if it is HDMI or DP, not checking the
port type that HTI is using.
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108134802.21280-1-jose.souza@intel.com
The bspec has been updated with new vswing programming for RKL DP. No
data is provided for HDMI or eDP, so for now we'll continue to assume
that those are the same as TGL.
Bspec: 49291
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218040535.45492-1-matthew.d.roper@intel.com
Reviewed-by: Swathi Dhanavanthri <swathi.dhanavanthri@intel.com>
If PCON has capability to convert RGB->YCbCr colorspace and also
to 444->420 downsampling then for any YUV420 only mode, we can
let the PCON do all the conversion. If the PCON supports
RGB->YCbCr conversion for all BT2020, BT709, BT601, choose
the one that is selected by userspace via connector colorspace
property, otherwise default to BT601.
v2: As suggested by Uma Shankar, considered case for colorspace
BT709 and BT2020, and default to BT601. Also appended dir
'display' in commit message.
v3: Fixed typo in condition for printing one of the error msg.
v4: As suggested by Uma Shankar:
-Fixed bug in determining the colorspace for RGB->YCbCr conversion.
-Fixed minor formatting issues
Also updated the commit message as per latest changes.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
[Jani: Fixed checkpatch PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-16-ankit.k.nautiyal@intel.com
When a source supporting DSC1.1 is connected to DSC1.2 HDMI2.1 sink
via DP HDMI2.1 PCON, the PCON can be configured to decode the
DSC1.1 compressed stream and encode to DSC1.2. It then sends the
DSC1.2 compressed stream to the HDMI2.1 sink.
This patch configures the PCON for DSC1.1 to DSC1.2 encoding, based
on the PCON's DSC encoder capablities and HDMI2.1 sink's DSC decoder
capabilities.
v2: Addressed review comments from Uma Shankar:
-fixed the error in packing pps parameter values
-added check for pcon in the pcon related function
-appended display in commit message
v3: Only consider non-zero DSC FRL b/w for determining max FRL b/w
supported by sink.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
[Jani: Fixed checkpatch BRACES, LINE_SPACING, PARENTHESIS_ALIGNMENT.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-15-ankit.k.nautiyal@intel.com
This patch calls functions to check FRL training requirements
for an HDMI2.1 sink, when connected through PCON.
The call is made before the DP link training. In case FRL is not
required or failure during FRL training, the TMDS mode is selected
for the pcon.
v2: moved check_frl_training() just after FEC READY, before
starting DP link training.
v3: rebase
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218103723.30844-11-ankit.k.nautiyal@intel.com
The Bspec does not mention polling the FEC Enable
Live status bit. That is only there for debug purposes.
So remove the polling from driver.
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201125072634.27664-1-manasi.d.navare@intel.com
Lspcon has Infoframes as well as DIP for HDR metadata(DRM Infoframe).
Create a separate mechanism for lspcon compared to HDMI in order to
address the same and ensure future scalability.
v2: Streamlined this as per Ville's suggestions, making sure that
HDMI infoframe versions are directly returned instead of a redundant
and confusing DIP overhead.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201130204738.2443-12-uma.shankar@intel.com
Skip iterating over bigjoiner slaves, only the master has the state we
care about.
Add the width of the bigjoiner slave to the reconstructed fb.
Hide the bigjoiner slave to userspace, and double the mode on bigjoiner
master.
And last, disable bigjoiner slave from primary if reconstruction fails.
v3:
* Fix the ddi_get_config slave error (Ankit Nautiyal)
v2:
* Unsupported bigjoiner config for initial fb (Ville)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala:
* Don't do any hw->uapi state copy for bigjoiner slave
* We still have hw.mode so no need to pass it in
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-7-manasi.d.navare@intel.com
Enabling is done in a special sequence and so should plane updates
be. Ideally the end user never notices the second pipe is used.
This way ideally everything will be tear free, and updates are
really atomic as userspace expects it.
This uses generic modeset_enables() calls like trans port sync
but still has special handling for disable since for slave we
should not disable things like encoder, plls that are not enabled
for slave.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala: Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-6-manasi.d.navare@intel.com
Make vdsc work when no output is enabled. The big joiner needs VDSC
on the slave, so enable it and set the appropriate bits.
So remove encoder usage from dsc functions.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-5-manasi.d.navare@intel.com
I totally fumbled the ?: usage when generating the DDI encoder
names. Reverse the things that need reversing, and to make it
a bit less messy add a few macros to hide the arithmetic on the
port enums.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Fixes: 2d709a5a62 ("drm/i915: Give DDI encoders even better names")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117154028.8516-1-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Currently the DPLL .get_freq() uses pll->state.hw_state which
is not the thing we actually read out (except during driver
load/resume). Outside of that pll->state.hw_state is just the
thing we committed last time around. During state check we
just read the thing into crtc_state->dpll_hw_state, so that
is what we should use for calculating the DPLL output frequency.
I think we used to do this so that the results of the readout
were actually used, but somehow it got changed when the
.get_freq() refactoring happened.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109231239.17002-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
JSL has update in vswing table for eDP.
BSpec: 21257
Changes since V1:
- Fixed few checkpatch errors
Cc: Souza Jose <jose.souza@intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020053657.99890-1-tejaskumarx.surendrakumar.upadhyay@intel.com
DG1 uses 2 registers for the ddi clock mapping, with PHY A and B using
DPCLKA_CFGCR0 and PHY C and D using DPCLKA1_CFGCR0. Hide this behind a
single macro that chooses the correct register according to the phy
being accessed, use the correct bitfields for each pll/phy and implement
separate functions for DG1 since it doesn't share much with ICL/TGL
anymore.
The previous values were correct for PHY A and B since they were using
the same register as before and the bitfields were matching.
v2: Add comment and try to simplify DG1_DPCLKA* macros by reusing
previous ones
v3:
- Fix DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK() after wrong macro reuse
- Move phy -> id map to a separate macro (Aditya)
- Remove DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK where not required
(Aditya)
- Use drm_WARN_ON
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Aditya Swarup <aditya.swarup@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106210006.837953-1-lucas.demarchi@intel.com
Let's pimp the DDI encoder->name to reflect what the spec calls them.
Ie. on pre-tgl DDI A-F, on tgl+ DDI A-C or DDI TC1-6.
Also since each encoder is really a combination of the DDI and the PHY
we include the PHY name as well.
ICL is a bit special since it already has the two different types
of DDIs (combo or TC) but it still calls them just DDI A-F regarless
of the type. For that let's add an extra "(TC)" note to remind
is which type of DDI it really is.
The code is darn ugly, but not sure there's much we can do about it.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-4-ville.syrjala@linux.intel.com
DG1 has one more combo phy port, no TC and all irq handling goes through
SDE, like for MCC.
v2: Also change intel_hpd_pin_default() to include DG1 mapping
v3, v4: Rebase on hpd refactor
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-2-lucas.demarchi@intel.com
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.
Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c
Cc : Matt Roper <matthew.d.roper@intel.com>
Cc : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com
Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Recent update in documentation defeatured eDP HBR3 for EHL and JSL.
v2:
- Remove dead code in ehl_get_combo_buf_trans()
v3:
- Rebase
BSpec: 32247
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005175447.93430-1-jose.souza@intel.com
Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.
A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.
The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3
v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.
v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com
Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.
v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com
On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[ 3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[ 3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D
Seems like the lspcon chip on the system only gets powered after the
cable is plugged.
Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.
v6:
- Rebase on latest for-linux-next.
v5:
- Consolidate lspcon_resume() with lspcon_init().
- Move more logic into lspcon code.
v4:
- Trust VBT in intel_infoframe_init().
- Init lspcon in intel_dp_detect().
v3:
- Make sure it's handled under long HPD case.
v2:
- Move lspcon_init() inside of intel_dp_hpd_pulse().
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com
Now that we've plumbed the crtc state all the way down we can
eliminate the DP_TP_{CTL,STATUS} register offsets from intel_dp,
and instead we derive them directly from the crtc state.
And thus we can get rid of the nasty hack in intel_ddi_get_config()
which mutates intel_dp during the readout.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-12-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.
Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.
v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com
