If reloading the static config fails for whatever reason, for example if
sja1105_static_config_check_valid() fails, then we "goto out_unlock_ptp"
but we print anyway that "Reset switch and programmed static config.",
which is confusing because we didn't. We also do a bunch of other stuff
like reprogram the XPCS and reload the credit-based shapers, as if a
switch reset took place, which didn't.
So just unlock the PTP lock and goto out, skipping all of that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sja1105_static_config_check_valid() is coded up to detect
whether TTEthernet is supported based on device ID, and this check was
not updated to cover SJA1110.
However, it is desirable to have as few checks for the device ID as
possible, so the driver core is more generic. So what we can do is look
at the static config table operations implemented by that specific
switch family (populated by sja1105_static_config_init) whether the
schedule table has a non-zero maximum entry count (meaning that it is
supported) or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that powering down the BASE_TIMER_CLK does not turn off the
microcontroller, just its timers, including the one for the watchdog.
So the embedded microcontroller is still running, and potentially still
doing things.
To prevent unwanted interference, we should power down the BASE_MCSS_CLK
as well (MCSS = microcontroller subsystem).
The trouble is that currently we turn off the BASE_TIMER_CLK for SJA1110
from the .clocking_setup() method, mostly because this is a Clock
Generation Unit (CGU) setting which was traditionally configured in that
method for SJA1105. But in SJA1105, the CGU was used for bringing up the
port clocks at the proper speeds, and in SJA1110 it's not (but rather
for initial configuration), so it's best that we rebrand the
sja1110_clocking_setup() method into what it really is - an implementation
of the .disable_microcontroller() method.
Since disabling the microcontroller only needs to be done once, at probe
time, we can choose the best place to do that as being in sja1105_setup(),
before we upload the static config to the device. This guarantees that
the static config being used by the switch afterwards is really ours.
Note that the procedure to upload a static config necessarily resets the
switch. This already did not reset the microcontroller, only the switch
core, so since the .disable_microcontroller() method is guaranteed to be
called by that point, if it's disabled, it remains disabled. Add a
comment to make that clear.
With the code movement for SJA1110 from .clocking_setup() to
.disable_microcontroller(), both methods are optional and are guarded by
"if" conditions.
Tested by enabling in the device tree the rev-mii switch port 0 that
goes towards the microcontroller, and flashing a firmware that would
have networking. Without this patch, the microcontroller can be pinged,
with this patch it cannot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward supervision frames between redunant HSR ports. This was broken
in the last commit.
Fixes: 1a42624aec ("net: dsa: xrs700x: allow HSR/PRP supervision dupes for node_table")
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer dev can never be null, the null check is redundant
and can be removed. Cleans up a static analysis warning that
pointer priv is dereferencing dev before dev is being null
checked.
Addresses-Coverity: ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct sja1105_regs tables are not modified during the runtime of
the driver, so they can be made constant. In fact, struct sja1105_info
already holds a const pointer to these.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.
The patch was tested on a KSZ8873RLL switch with following results:
- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)
- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mapping for LINK_MD register to enable cable testing functionality.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phylink support to the ksz8795 driver to provide
configuration exceptions on quirky KSZ8863 and KSZ8873 ports.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some micrel devices share the same PHY register defines. This patch
moves them to one common header so other drivers can reuse them.
And reuse generic MII_* defines where possible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC treats 2500base-x same as SGMII (yay for that) except that it
must be set to a different speed.
Extend all places that check for SGMII to also check for 2500base-x.
Also add the missing 2500base-x compatibility matrix entry for SJA1110D.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the xMII Mode Parameters Table to be properly configured for SGMII
mode on SJA1110, we need to set the "special" bit, since SGMII is
officially bitwise coded as 0b0011 in SJA1105 (decimal 3, equal to
XMII_MODE_SGMII), and as 0b1011 in SJA1110 (decimal 11).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the SJA1110, the PCS of each SERDES-capable port is accessed through
a different memory window which is 0x100 bytes in size, denoted by
"pcs_base".
In each PCS register access window, the XPCS MMDs are accessed in an
indirect way: in pages/banks of up to 0x100 addresses each. Changing the
page/bank is done by writing to a special register at the end of the
access window.
The MDIO register map accessed indirectly through the indirect banked
method described above is similar to what SJA1105 has: upper 5 bits are
the MMD, lower 16 bits are the MDIO address within that MMD.
Since the PHY ID reported by the XPCS inside SJA1110 is also all zeroes
(like SJA1105), we need to trap those reads and return a fake PHY ID so
that the xpcs driver can apply some specific fixups for our integration.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire to use the generic driver for the Synopsys XPCS
located in drivers/net/pcs, and to achieve that, the sja1105 driver must
expose an MDIO bus for the SGMII PCS, because the XPCS probes as an
mdio_device.
In preparation of the SJA1110 which in fact has a different access
procedure for the SJA1105, we register this PCS MDIO bus once in the
common code, but we implement function pointers for the read and write
methods. In this patch there is a single implementation for them.
There is exactly one MDIO bus for the PCS, this will contain all PCSes
at MDIO addresses equal to the port number.
We delete a bunch of hardware support code because the xpcs driver
already does what we need.
We need to hack up the MDIO reads for the PHY ID, since our XPCS
instantiation returns zeroes and there are some specific fixups which
need to be applied by the xpcs driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX timestamping procedure for SJA1105 is a bit unconventional
because the transmit procedure itself is unconventional.
Control packets (and therefore PTP as well) are transmitted to a
specific port in SJA1105 using "management routes" which must be written
over SPI to the switch. These are one-shot rules that match by
destination MAC address on traffic coming from the CPU port, and select
the precise destination port for that packet. So to transmit a packet
from NET_TX softirq context, we actually need to defer to a process
context so that we can perform that SPI write before we send the packet.
The DSA master dev_queue_xmit() runs in process context, and we poll
until the switch confirms it took the TX timestamp, then we annotate the
skb clone with that TX timestamp. This is why the sja1105 driver does
not need an skb queue for TX timestamping.
But the SJA1110 is a bit (not much!) more conventional, and you can
request 2-step TX timestamping through the DSA header, as well as give
the switch a cookie (timestamp ID) which it will give back to you when
it has the timestamp. So now we do need a queue for keeping the skb
clones until their TX timestamps become available.
The interesting part is that the metadata frames from SJA1105 haven't
disappeared completely. On SJA1105 they were used as follow-ups which
contained RX timestamps, but on SJA1110 they are actually TX completion
packets, which contain a variable (up to 32) array of timestamps.
Why an array? Because:
- not only is the TX timestamp on the egress port being communicated,
but also the RX timestamp on the CPU port. Nice, but we don't care
about that, so we ignore it.
- because a packet could be multicast to multiple egress ports, each
port takes its own timestamp, and the TX completion packet contains
the individual timestamps on each port.
This is unconventional because switches typically have a timestamping
FIFO and raise an interrupt, but this one doesn't. So the tagger needs
to detect and parse meta frames, and call into the main switch driver,
which pairs the timestamps with the skbs in the TX timestamping queue
which are waiting for one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is really easy, since the full RX timestamp is in the DSA trailer
and the tagger code transfers it to SJA1105_SKB_CB(skb)->tstamp, we just
need to move it to the skb shared info region. This is as opposed to
SJA1105, where the RX timestamp was received in a meta frame (so there
needed to be a state machine to pair the 2 packets) and the timestamp
was partial (so the packet, once matched with its timestamp, needed to
be added to an RX timestamping queue where the PTP aux worker would
reconstruct that timestamp).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 has improved a few things compared to SJA1105:
- To send a control packet from the host port with SJA1105, one needed
to program a one-shot "management route" over SPI. This is no longer
true with SJA1110, you can actually send "in-band control extensions"
in the packets sent by DSA, these are in fact DSA tags which contain
the destination port and switch ID.
- When receiving a control packet from the switch with SJA1105, the
source port and switch ID were written in bytes 3 and 4 of the
destination MAC address of the frame (which was a very poor shot at a
DSA header). If the control packet also had an RX timestamp, that
timestamp was sent in an actual follow-up packet, so there were
reordering concerns on multi-core/multi-queue DSA masters, where the
metadata frame with the RX timestamp might get processed before the
actual packet to which that timestamp belonged (there is no way to
pair a packet to its timestamp other than the order in which they were
received). On SJA1110, this is no longer true, control packets have
the source port, switch ID and timestamp all in the DSA tags.
- Timestamps from the switch were partial: to get a 64-bit timestamp as
required by PTP stacks, one would need to take the partial 24-bit or
32-bit timestamp from the packet, then read the current PTP time very
quickly, and then patch in the high bits of the current PTP time into
the captured partial timestamp, to reconstruct what the full 64-bit
timestamp must have been. That is awful because packet processing is
done in NAPI context, but reading the current PTP time is done over
SPI and therefore needs sleepable context.
But it also aggravated a few things:
- Not only is there a DSA header in SJA1110, but there is a DSA trailer
in fact, too. So DSA needs to be extended to support taggers which
have both a header and a trailer. Very unconventional - my understanding
is that the trailer exists because the timestamps couldn't be prepared
in time for putting them in the header area.
- Like SJA1105, not all packets sent to the CPU have the DSA tag added
to them, only control packets do:
* the ones which match the destination MAC filters/traps in
MAC_FLTRES1 and MAC_FLTRES0
* the ones which match FDB entries which have TRAP or TAKETS bits set
So we could in theory hack something up to request the switch to take
timestamps for all packets that reach the CPU, and those would be
DSA-tagged and contain the source port / switch ID by virtue of the
fact that there needs to be a timestamp trailer provided. BUT:
- The SJA1110 does not parse its own DSA tags in a way that is useful
for routing in cross-chip topologies, a la Marvell. And the sja1105
driver already supports cross-chip bridging from the SJA1105 days.
It does that by automatically setting up the DSA links as VLAN trunks
which contain all the necessary tag_8021q RX VLANs that must be
communicated between the switches that span the same bridge. So when
using tag_8021q on sja1105, it is possible to have 2 switches with
ports sw0p0, sw0p1, sw1p0, sw1p1, and 2 VLAN-unaware bridges br0 and
br1, and br0 can take sw0p0 and sw1p0, and br1 can take sw0p1 and
sw1p1, and forwarding will happen according to the expected rules of
the Linux bridge.
We like that, and we don't want that to go away, so as a matter of
fact, the SJA1110 tagger still needs to support tag_8021q.
So the sja1110 tagger is a hybrid between tag_8021q for data packets,
and the native hardware support for control packets.
On RX, packets have a 13-byte trailer if they contain an RX timestamp.
That trailer is padded in such a way that its byte 8 (the start of the
"residence time" field - not parsed by Linux because we don't care) is
aligned on a 16 byte boundary. So the padding has a variable length
between 0 and 15 bytes. The DSA header contains the offset of the
beginning of the padding relative to the beginning of the frame (and the
end of the padding is obviously the end of the packet minus 13 bytes,
the length of the trailer). So we discard it.
Packets which don't have a trailer contain the source port and switch ID
information in the header (they are "trap-to-host" packets). Packets
which have a trailer contain the source port and switch ID in the trailer.
On TX, the destination port mask and switch ID is always in the trailer,
so we always need to say in the header that a trailer is present.
The header needs a custom EtherType and this was chosen as 0xdadc, after
0xdada which is for Marvell and 0xdadb which is for VLANs in
VLAN-unaware mode on SJA1105 (and SJA1110 in fact too).
Because we use tag_8021q in concert with the native tagging protocol,
control packets will have 2 DSA tags.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SJA1105, RX timestamps for packets sent to the CPU are transmitted in
separate follow-up packets (metadata frames). These contain partial
timestamps (24 or 32 bits) which are kept in SJA1105_SKB_CB(skb)->meta_tstamp.
Thankfully, SJA1110 improved that, and the RX timestamps are now
transmitted in-band with the actual packet, in the timestamp trailer.
The RX timestamps are now full-width 64 bits.
Because we process the RX DSA tags in the rcv() method in the tagger,
but we would like to preserve the DSA code structure in that we populate
the skb timestamp in the port_rxtstamp() call which only happens later,
the implication is that we must somehow pass the 64-bit timestamp from
the rcv() method all the way to port_rxtstamp(). We can use the skb->cb
for that.
Rename the meta_tstamp from struct sja1105_skb_cb from "meta_tstamp" to
"tstamp", and increase its size to 64 bits.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SJA1105, there is support for a cascade port which is presumably
connected to a downstream SJA1105 switch. The upstream one does not take
PTP timestamps for packets received on this port, presumably because the
downstream switch already did (and for PTP, it only makes sense for the
leaf nodes in a DSA switch tree to do that).
I haven't been able to validate that feature in a fully assembled setup,
so I am disabling the feature by setting the cascade port to an unused
port value (ds->num_ports).
In SJA1110, multiple cascade ports are supported, and CASC_PORT became
a bit mask from a port number. So when CASC_PORT is set to ds->num_ports
(which is 11 on SJA1110), it is actually set to 0b1011, so ports 3, 1
and 0 are configured as cascade ports and we cannot take RX timestamps
on them.
So we need to introduce a check for SJA1110 and set things differently
(to zero there), so that the cascading feature is properly disabled and
RX timestamps can be taken on all ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As opposed to SJA1105 where there are parts with TTEthernet and parts
without, in SJA1110 all parts support it, but it must be enabled in the
static config. So enable it unconditionally. We use it for the tc-taprio
and tc-gate offload.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return code variable rc is being set to return error values in two
places in sja1105_mdiobus_base_tx_register and yet it is not being
returned, the function always returns 0 instead. Fix this by replacing
the return 0 with the return code rc.
Addresses-Coverity: ("Unused value")
Fixes: 5a8f09748e ("net: dsa: sja1105: register the MDIO buses for 100base-T1 and 100base-TX")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code check "reg" but "ret" was intended so the error handling will
never trigger.
Fixes: 7c9896e378 ("net: dsa: qca8k: check return value of read functions correctly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "hi" variable is a u64 but the qca8k_read() writes to the top 32
bits of it. That will work on little endian systems but it's a bit
subtle. It's cleaner to make declare "hi" as a u32. We will still need
to cast it when we shift it later on in the function but that's fine.
Fixes: 7c9896e378 ("net: dsa: qca8k: check return value of read functions correctly")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ca89319483 ("net: dsa: b53: Keep CPU port as tagged in all
VLANs") forced the CPU port to be always tagged in any VLAN membership.
This was necessary back then because we did not support Broadcom tags
for all configurations so the only way to differentiate tagged and
untagged traffic while DSA_TAG_PROTO_NONE was used was to force the CPU
port into being always tagged.
With most configurations enabling Broadcom tags, especially after
8fab459e69 ("net: dsa: b53: Enable Broadcom tags for 531x5/539x
families") we do not need to apply this unconditional force tagging of
the CPU port in all VLANs.
A helper function is introduced to faciliate the encapsulation of the
specific condition requiring the CPU port to be tagged in all VLANs and
the dsa_switch_ops::untag_bridge_pvid boolean is moved to when
dsa_switch_ops::setup is called when we have already determined the
tagging protocol we will be using.
Reported-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on the static initialization done by ocelot_init_port()
which enables flow control unconditionally, set SYS_PAUSE_CFG_PAUSE_ENA
according to the parameters negotiated by the PHY.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 contains two types of integrated PHYs: one 100base-TX PHY
and multiple 100base-T1 PHYs.
The access procedure for the 100base-T1 PHYs is also different than it
is for the 100base-TX one. So we register 2 MDIO buses, one for the
base-TX and the other for the base-T1. Each bus has an OF node which is
a child of the "mdio" subnode of the switch, and they are recognized by
compatible string.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 has an extra configuration in the General Parameters Table
through which the user can select the buffer reservation config.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 is basically an SJA1105 with more ports, some integrated
PHYs (100base-T1 and 100base-TX) and an embedded microcontroller which
can be disabled, and the switch core can be controlled by a host running
Linux, over SPI.
This patch contains:
- the static and dynamic config packing functions, for the tables that
are common with SJA1105
- one more static config tables which is "unique" to the SJA1110
(actually it is a rehash of stuff that was placed somewhere else in
SJA1105): the PCP Remapping Table
- a reset and clock configuration procedure for the SJA1110 switch.
This resets just the switch subsystem, and gates off the clock which
powers on the embedded microcontroller.
- an RGMII delay configuration procedure for SJA1110, which is very
similar to SJA1105, but different enough for us to be unable to reuse
it (this is a pattern that repeats itself)
- some adaptations to dynamic config table entries which are no longer
programmed in the same way. For example, to delete a VLAN, you used to
write an entry through the dynamic reconfiguration interface with the
desired VLAN ID, and with the VALIDENT bit set to false. Now, the VLAN
table entries contain a TYPE_ENTRY field, which must be set to zero
(in a backwards-incompatible way) in order for the entry to be deleted,
or to some other entry for the VLAN to match "inner tagged" or "outer
tagged" packets.
- a similar thing for the static config: the xMII Mode Parameters Table
encoding for SGMII and MII (the latter just when attached to a
100base-TX PHY) just isn't what it used to be in SJA1105. They are
identical, except there is an extra "special" bit which needs to be
set. Set it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using is_zero_ether_addr() instead of directly use
memcmp() to determine if the ethernet address is all
zeros.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that both RevMII as well as RevRMII exist, we can deprecate the
sja1105,role-mac and sja1105,role-phy properties and simply let the user
select that a port operates in MII PHY role by using
phy-mode = "rev-mii";
or in RMII PHY role by using
phy-mode = "rev-rmii";
There are no fixed-link MII or RMII properties in mainline device trees,
and the setup itself is fairly uncommon, so there shouldn't be risks of
breaking compatibility.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has an intermediate way of determining whether the
RGMII delays should be applied by the PHY or by itself: by looking at
the port role (PHY or MAC). The port can be put in the PHY role either
explicitly (sja1105,role-phy) or implicitly (fixed-link).
We want to deprecate the sja1105,role-phy property, so all that remains
is the fixed-link property. Introduce a "fixed_link" array of booleans
in the driver, and use that to determine whether RGMII delays must be
applied or not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an inbound policy filter which matches the HSR/PRP supervision
MAC range and forwards to the CPU port without discarding duplicates.
This is required to correctly populate time_in[A] and time_in[B] in the
HSR/PRP node_table. Leave the policy disabled by default and
enable/disable it when joining/leaving hsr.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1105 has a static configuration comprised of a number of tables
with entries. Some of these can be read and modified at runtime as well,
through the dynamic configuration interface.
As a careful reader can notice from the comments in this file, the
software interface for accessing a table entry through the dynamic
reconfiguration is a bit of a no man's land, and varies wildly across
switch generations and even from one kind of table to another.
I have tried my best to come up with a software representation of a
'common denominator' SPI command to access a table entry through the
dynamic configuration interface:
struct sja1105_dyn_cmd {
bool search;
u64 valid; /* must be set to 1 */
u64 rdwrset; /* 0 to read, 1 to write */
u64 errors;
u64 valident; /* 0 if entry is invalid, 1 if valid */
u64 index;
};
Relevant to this patch is the VALIDENT bit, which for READ commands is
populated by the switch and lets us know if we're looking at junk or at
a real table entry.
In SJA1105, the dynamic reconfiguration interface for management routes
has notably not implemented the VALIDENT bit, leading to a workaround to
ignore this field in sja1105_dynamic_config_read(), as it will be set to
zero, but the data is valid nonetheless.
In SJA1110, this pattern has sadly been abused to death, and while there
are many more tables which can be read back over the dynamic config
interface compared to SJA1105, their handling isn't in any way more
uniform. Generally speaking, if there is a single possible entry in a
given table, and loading that table in the static config is mandatory as
per the documentation, then the VALIDENT bit is deemed as redundant and
more than likely not implemented.
So it is time to make the workaround more official, and add a bit to the
flags implemented by dynamic config tables. It will be used by more
tables when SJA1110 support arrives.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In SJA1105, the xMII Mode Parameters Table field called PHY_MAC denotes
the 'role' of the port, be it a PHY or a MAC. This makes a difference in
the MII and RMII protocols, but RGMII is symmetric, so either PHY or MAC
settings result in the same hardware behavior.
The SJA1110 is different, and the RGMII ports only work when configured
in MAC mode, so keep the port roles in MAC mode unconditionally.
Why we had an RGMII port in the PHY role in the first place was because
we wanted to have a way in the driver to denote whether RGMII delays
should be applied based on the phy-mode property or not. This is already
done in sja1105_parse_rgmii_delays() based on an intermediary
struct sja1105_dt_port (which contains the port role). So it is a
logical fallacy to use the hardware configuration as a scratchpad for
driver data, it isn't necessary.
We can also remove the gating condition for applying RGMII delays only
for ports in the PHY role. The .setup_rgmii_delay() method looks at
the priv->rgmii_rx_delay[port] and priv->rgmii_tx_delay[port] properties
which are already populated properly (in the case of a port in the MAC
role they are false). Removing this condition generates a few more SPI
writes for these ports (clearing the RGMII delays) which are perhaps
useless for SJA1105P/Q/R/S, where we know that the delays are disabled
by default. But for SJA1110, the firmware on the embedded microcontroller
might have done something funny, so it's always a good idea to clear the
RGMII delays if that's what Linux expects.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to support the new speed of 2500Mbps, the SJA1110 has achieved
the great performance of changing the encoding in the MAC Configuration
Table for the port speeds of 10, 100, 1000 compared to SJA1105.
Because this is a common driver, we need a layer of indirection in order
to program the hardware with the right values irrespective of switch
generation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On the SJA1105, all ports support the parallel "xMII" protocols (MII,
RMII, RGMII) except for port 4 on SJA1105R/S which supports only SGMII.
This was relatively easy to model, by special-casing the SGMII port.
On the SJA1110, certain ports can be pinmuxed between SGMII and xMII, or
between SGMII and an internal 100base-TX PHY. This creates problems,
because the driver's assumption so far was that if a port supports
SGMII, it uses SGMII.
We allow the device tree to tell us how the port pinmuxing is done, and
check that against a PHY interface type compatibility matrix for
plausibility.
The other big change is that instead of doing SGMII configuration based
on what the port supports, we do it based on what is the configured
phy_mode of the port.
The 2500base-x support added in this patch is not complete.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far we've succeeded in operating without keeping a copy of the
phy-mode in the driver, since we already have the static config and we
can look at the xMII Mode Parameters Table which already holds that
information.
But with the SJA1110, we cannot make the distinction between sgmii and
2500base-x, because to the hardware's static config, it's all SGMII.
So add a phy_mode property per port inside struct sja1105_private.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Looking at the SGMII PCS from SJA1110, which is accessed indirectly
through a different base address as can be seen in the next patch, it
appears odd that the address accessed through indirection still
references the base address from the SJA1105S register map (first MDIO
register is at 0x1f0000), when it could index the SGMII registers
starting from zero.
Except that the 0x1f0000 is not a base address at all, it seems. It is
0x1f << 16 | 0x0000, and 0x1f is coding for the vendor-specific MMD2.
So, it turns out, the Synopsys PCS implements all its registers inside
the vendor-specific MMDs 1 and 2 (0x1e and 0x1f). This explains why the
PCS has no overlaps (for the other MMDs) with other register regions of
the switch (because no other MMDs are implemented).
Change the code to remove the SGMII "base address" and explicitly encode
the MMD for reads/writes. This will become necessary for SJA1110 support.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The SJA1105 R and S switches have 1 SGMII port (port 4). Because there
is only one such port, there is no "port" parameter in the configuration
code for the SGMII PCS.
However, the SJA1110 can have up to 4 SGMII ports, each with its own
SGMII register map. So we need to generalize the logic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit f2f3e09396be ("net: dsa: sja1105: be compatible with
"ethernet-ports" OF node name"), DSA supports the "ethernet-ports" name
for the container node of the ports, but the sja1105 driver doesn't,
because it handles some device tree parsing of its own.
Add the second node name as a fallback.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now we can check qca8k_read() return value correctly, so if
it fails, we need return directly.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current return type of qca8k_mii_read32() and qca8k_read() are
unsigned, it can't be negative, so the return value check is
unuseful. For check the return value correctly, change return
type of the read functions and add a output parameter to store
the read value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Also enable phy errata workaround on 9567 since has the same errata as
the 9477 according to the manufacture's documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shared frame buffer of the SJA1110 is larger than that of SJA1105,
which is natural due to the fact that there are more ports.
Introduce yet another property in struct sja1105_info which encodes the
maximum number of 128 byte blocks that can be used for frame buffers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1110 policer array is similar in layout with SJA1105, except it
contains one multicast policer per port at the end.
Detect the presence of multicast policers based on the maximum number of
supported L2 Policing Table entries, and make those policers have a
shared index equal to the port's default policer. Letting the user
configure these policers is not supported at the moment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using sja1105_xfer_buf results in a higher overhead and is harder to
read.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that the port count is different, some static config
tables have a different number of elements in SJA1105 compared to
SJA1110. Such an example is the L2 Policing table, which has 45 entries
in SJA1105 (one per port x traffic class, and one broadcast policer per
port) and 110 entries in SJA1110 (one per port x traffic class, one
broadcast and one multicast policer per port).
Similarly, the MAC Configuration Table, the L2 Forwarding table, all
have a different number of elements simply because the port count is
different, and although this can be accounted for by looking at
ds->ports, the policing table can't because of the presence of the extra
multicast policers.
The common denominator for the static config initializers for these
tables is that they must set up all the entries within that table.
So the simplest way to account for these differences in a uniform manner
is to look at struct sja1105_table_ops::max_entry_count. For the sake of
uniformity, this patch makes that change also for tables whose number of
elements did not change in SJA1110, like the xMII Mode Parameters, the
L2 Lookup Parameters, General Parameters, AVB Parameters (all of these
are singleton tables with a single entry).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two distinct code paths which enter sja1105_clocking.c, one
through sja1105_clocking_setup() and the other through
sja1105_clocking_setup_port():
sja1105_static_config_reload sja1105_setup
| |
| +------------------+
| |
v v
sja1105_clocking_setup sja1105_adjust_port_config
| |
v |
sja1105_clocking_setup_port <------------------+
As opposed to SJA1105, the SJA1110 does not need any configuration of
the Clock Generation Unit in order for xMII ports to work. Just RGMII
internal delays need to be configured, and that is done inside
sja1105_clocking_setup_port for the RGMII ports.
So this patch introduces the concept of a "reserved address", which the
CGU configuration functions from sja1105_clocking.c must check before
proceeding to do anything. The SJA1110 will have reserved addresses for
the CGU PLLs for MII/RMII/RGMII.
Additionally, make sja1105_clocking_setup() a function pointer so it can
be overridden by the SJA1110. Even though nothing port-related needs to
be done in the CGU, there are some operations such as disabling the
watchdog clock which are unique to the SJA1110.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If @port is unused, then dsa_upstream_port(ds, port) returns @port,
which means we cannot assume the CPU port can be retrieved this way.
The sja1105 switches support a single CPU port, so just iterate over the
switch ports and stop at the first CPU port we see.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a SJA1105_MAX_NUM_PORTS macro which at the moment is equal to
SJA1105_NUM_PORTS (5). With the introduction of SJA1110, these
structures will need to hold information for up to 11 ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not put unused ports in the forwarding domain, and do not allocate
FDB entries for dynamic address learning for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver will gain support for the next-gen SJA1110 switch,
which is very similar except for the fact it has more than 5 ports.
So we need to replace the hardcoded SJA1105_NUM_PORTS in this driver
with ds->num_ports. This patch is as mechanical as possible (save for
the fact that ds->num_ports is not an integer constant expression).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running this sequence of operations:
ip link add br0 type bridge vlan_filtering 1
ip link set swp4 master br0
bridge vlan add dev swp4 vid 1
We observe the traffic sent on swp4 is still untagged, even though the
bridge has overwritten the existing VLAN entry:
port vlan ids
swp4 1 PVID
br0 1 PVID Egress Untagged
This happens because we didn't consider that the 'bridge vlan add'
command just overwrites VLANs like it's nothing. We treat the 'vid 1
pvid untagged' and the 'vid 1' as two separate VLANs, and the first
still has precedence when calling sja1105_build_vlan_table. Obviously
there is a disagreement regarding semantics, and we end up doing
something unexpected from the PoV of the bridge.
Let's actually consider an "existing VLAN" to be one which is on the
same port, and has the same VLAN ID, as one we already have, and update
it if it has different flags than we do.
The first blamed commit is the one introducing the bug, the second one
is the latest on top of which the bugfix still applies.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Fixes: 5899ee367a ("net: dsa: tag_8021q: add a context structure")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One thing became visible when writing the blamed commit, and that was
that STP and PTP frames injected by net/dsa/tag_sja1105.c using the
deferred xmit mechanism are always classified to the pvid of the CPU
port, regardless of whatever VLAN there might be in these packets.
So a decision needed to be taken regarding the mechanism through which
we should ensure that delivery of STP and PTP traffic is possible when
we are in a VLAN awareness mode that involves tag_8021q. This is because
tag_8021q is not concerned with managing the pvid of the CPU port, since
as far as tag_8021q is concerned, no traffic should be sent as untagged
from the CPU port. So we end up not actually having a pvid on the CPU
port if we only listen to tag_8021q, and unless we do something about it.
The decision taken at the time was to keep VLAN 1 in the list of
priv->dsa_8021q_vlans, and make it a pvid of the CPU port. This ensures
that STP and PTP frames can always be sent to the outside world.
However there is a problem. If we do the following while we are in
the best_effort_vlan_filtering=true mode:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan del dev swp2 vid 1
Then untagged and pvid-tagged frames should be dropped. But we observe
that they aren't, and this is because of the precaution we took that VID
1 is always installed on all ports.
So clearly VLAN 1 is not good for this purpose. What about VLAN 0?
Well, VLAN 0 is managed by the 8021q module, and that module wants to
ensure that 802.1p tagged frames are always received by a port, and are
always transmitted as VLAN-tagged (with VLAN ID 0). Whereas we want our
STP and PTP frames to be untagged if the stack sent them as untagged -
we don't want the driver to just decide out of the blue that it adds
VID 0 to some packets.
So what to do?
Well, there is one other VLAN that is reserved, and that is 4095:
$ ip link add link swp2 name swp2.4095 type vlan id 4095
Error: 8021q: Invalid VLAN id.
$ bridge vlan add dev swp2 vid 4095
Error: bridge: Vlan id is invalid.
After we made this change, VLAN 1 is indeed forwarded and/or dropped
according to the bridge VLAN table, there are no further alterations
done by the sja1105 driver.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver continues probing when a port is configured for an
unsupported PHY interface type, instead it should stop.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any of sja1105_static_config_load(), sja1105_clocking_setup() or
sja1105_devlink_setup() fails, we can't just return in the middle of
sja1105_setup() or memory will leak. Add a cleanup path.
Fixes: 0a7bdbc23d ("net: dsa: sja1105: move devlink param code to sja1105_devlink.c")
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other drivers which pretty much end their .probe() execution with
dsa_register_switch(), the sja1105 does some extra stuff. When that
fails with -ENOMEM, the driver is quick to return that, forgetting to
call dsa_unregister_switch(). Not critical, but a bug nonetheless.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Fixes: a68578c20a ("net: dsa: Make deferred_xmit private to sja1105")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of the sja1105_dynamic_config.c file there is a diagram
of the dynamic config interface layout:
packed_buf
|
V
+-----------------------------------------+------------------+
| ENTRY BUFFER | COMMAND BUFFER |
+-----------------------------------------+------------------+
<----------------------- packed_size ------------------------>
So in order to pack/unpack the command bits into the buffer,
sja1105_vl_lookup_cmd_packing must first advance the buffer pointer by
the length of the entry. This is similar to what the other *cmd_packing
functions do.
This bug exists because the command packing function for P/Q/R/S was
copied from the E/T generation, and on E/T, the command was actually
embedded within the entry buffer itself.
Fixes: 94f94d4acf ("net: dsa: sja1105: add static tables for virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCR_MATRIX field was set to all 1's when VLAN filtering is enabled, but
was not reset when it is disabled, which may cause traffic leaks:
ip link add br0 type bridge vlan_filtering 1
ip link add br1 type bridge vlan_filtering 1
ip link set swp0 master br0
ip link set swp1 master br1
ip link set br0 type bridge vlan_filtering 0
ip link set br1 type bridge vlan_filtering 0
# traffic in br0 and br1 will start leaking to each other
As port_bridge_{add,del} have set up PCR_MATRIX properly, remove the
PCR_MATRIX write from mt7530_port_set_vlan_aware.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot call bcm_sf2_reg_rgmii_cntrl() for a port that is not RGMII,
yet we do that in bcm_sf2_sw_mac_link_up() irrespective of the port's
interface. Move that read until we have properly qualified the PHY
interface mode. This avoids triggering a warning on 7278 platforms that
have GMII ports.
Fixes: 55cfeb3969 ("net: dsa: bcm_sf2: add function finding RGMII register")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current internal sja1105 driver API is optimized for retrieving many
statistics counters at once. But the switch does not do atomic snapshotting
for them anyway.
In case we start reporting the hardware port counters through
ndo_get_stats64 as well, not just ethtool, it would be good to be able
to read individual port counters and not all of them.
Additionally, since Arnd Bergmann's commit ae1804de93 ("dsa: sja1105:
dynamically allocate stats structure"), sja1105_get_ethtool_stats
allocates memory dynamically, since struct sja1105_port_status was
deemed to consume too much stack memory. That is not ideal.
The large structure is only needed because of the burst read.
If we read statistics one by one, we can consume less memory, and
we can avoid dynamic allocation.
Additionally, latency-sensitive interfaces such as PTP operations (for
phc2sys) might suffer if the SPI mutex is being held for too long, which
happens in the case of SPI burst reads. By reading counters one by one,
we give a chance for higher priority processes to preempt and take the
SPI bus mutex for accessing the PTP clock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The queue levels are not counters, but instead they represent the
occupancy of the MAC TX queues. Having these in ethtool port counters is
not helpful, so remove them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static config of the sja1105 switch is a long stream of bytes which
is programmed to the hardware in chunks (portions with the chip select
continuously asserted) of max 256 bytes each. Each chunk is a
spi_message composed of 2 spi_transfers: the buffer with the data and a
preceding buffer with the SPI access header.
Only that certain SPI controllers, such as the spi-sc18is602 I2C-to-SPI
bridge, cannot keep the chip select asserted for that long.
The spi_max_transfer_size() and spi_max_message_size() functions are how
the controller can impose its hardware limitations upon the SPI
peripheral driver.
For the sja1105 driver to work with these controllers, both buffers must
be smaller than the transfer limit, and their sum must be smaller than
the message limit.
Regression-tested on a switch connected to a controller with no
limitations (spi-fsl-dspi) as well as with one with caps for both
max_transfer_size and max_message_size (spi-sc18is602).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver has been described by Mark Brown as "not using the
[ SPI ] API at all idiomatically" due to the use of cs_change:
https://patchwork.kernel.org/project/netdevbpf/patch/20210520135031.2969183-1-olteanv@gmail.com/
According to include/linux/spi/spi.h, the chip select is supposed to be
asserted for the entire length of a SPI message, as long as cs_change is
false for all member transfers. The cs_change flag changes the following:
(i) When a non-final SPI transfer has cs_change = true, the chip select
should temporarily deassert and then reassert starting with the next
transfer.
(ii) When a final SPI transfer has cs_change = true, the chip select
should remain asserted until the following SPI message.
The sja1105 driver only uses cs_change for its first property, to form a
single SPI message whose layout can be seen below:
this is an entire, single spi_message
_______________________________________________________________________________________________
/ \
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
| hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] |
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
cs_change false true false true false false
____________________________ _____________________________ _____________________________
CS line __/ \/ \ ... / \__
The fact of the matter is that spi_max_message_size() has an ambiguous
meaning if any non-final transfer has cs_change = true.
If the SPI master has a limitation in that it cannot keep the chip
select asserted for more than, say, 200 bytes (like the spi-sc18is602),
the normal thing for it to do is to implement .max_transfer_size and
.max_message_size, and limit both to 200: in the "worst case" where
cs_change is always false, then the controller can, indeed, not send
messages larger than 200 bytes.
But the fact that the SPI controller's max_message_size does not
necessarily mean that we cannot send messages larger than that.
Notably, if the SPI master special-cases the transfers with cs_change
and treats every chip select toggling as an entirely new transaction,
then a SPI message can easily exceed that limit. So there is a
temptation to ignore the controller's reported max_message_size when
using cs_change = true in non-final transfers.
But that can lead to false conclusions. As Mark points out, the SPI
controller might have a different kind of limitation with the max
message size, that has nothing at all to do with how long it can keep
the chip select asserted.
For example, that might be the case if the device is able to offload the
chip select changes to the hardware as part of the data stream, and it
packs the entire stream of commands+data (corresponding to a SPI
message) into a single DMA transfer that is itself limited in size.
So the only thing we can do is avoid ambiguity by not using cs_change at
all. Instead of sending a single spi_message, we now send multiple SPI
messages as follows:
spi_message 0 spi_message 1 spi_message n
____________________________ ___________________________ _____________________________
/ \ / \ / \
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
| hdr_xfer[0] | chunk_xfer[0] | hdr_xfer[1] | chunk_xfer[1] | | hdr_xfer[n] | chunk_xfer[n] |
+-------------+---------------+-------------+---------------+ ... +-------------+---------------+
cs_change false true false true false false
____________________________ _____________________________ _____________________________
CS line __/ \/ \ ... / \__
which is clearer because the max_message_size limit is now easier to
enforce. What is transmitted on the wire stays, of course, the same.
Additionally, because we send no more than 2 transfers at a time, we now
avoid dynamic memory allocation too, which might be seen as an
improvement by some.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MT7530 interrupt controller to handle internal PHYs.
In order to assign an IRQ number to each PHY, the registration of MDIO bus
is also done in this driver.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function qca8k_vlan_add()
and qca8k_vlan_del() in the error handling case.
Fixes: 028f5f8ef4 ("net: dsa: qca8k: handle error with qca8k_read operation")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define get_phy_flags to pass switch_Revision needed to tweak the
internal PHY with debug values based on the revision.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve the internal mdio read/write bus access by caching the value
without accessing it for every read/write.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to setup_mdio_bus for internal phy declaration. Introduce a
flag to use the legacy port phy mapping by default and use the direct
mapping if a mdio node is detected in the switch node. Register a
dedicated mdio internal mdio bus to address the different mapping
between port and phy if the mdio node is detected.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The witch require some extra delay after setting page or the next
read/write can use still use the old page. Add a delay after the
set_page function to address this as it's done in QSDK legacy driver.
Some timeouts were notice with VLAN and phy function, enlarge the
mdio busy wait timeout to fix these problems.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_MASTER operation have a dedicated busy wait that is not protected
by the mdio mutex. This can cause situation where the MASTER operation
is done and a normal operation is executed between the MASTER read/write
and the MASTER busy_wait. Rework the qca8k_mdio_read/write function to
address this issue by binding the lock for the whole MASTER operation
and not only the mdio read/write common operation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear MDIO_MASTER_EN bit from MDIO_MASTER_CTRL after read/write
operation. The MDIO_MASTER_EN bit is not reset after read/write
operation and the next operation can be wrongly interpreted by the
switch as a mdio operation. This cause a production of wrong/garbage
data from the switch and underfined bheavior. (random port drop,
unplugged port flagged with link up, wrong port speed)
Also on driver remove the MASTER_CTRL can be left set and cause the
malfunction of any next driver using the mdio device.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy qsdk code used a different delay instead of the max value.
Qsdk use 1 ns for rx and 2 ns for tx. Make these values configurable
using the standard rx/tx-internal-delay-ps ethernet binding and apply
qsdk values by default. The connected gmac doesn't add any delay so no
additional delay is added to tx/rx.
On this switch the delay is actually in ns so value should be in the
1000 order. Any value converted from ps to ns by dividing it by 1000
as the switch max value for delay is 3ns.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dsa now also supports ethernet-ports. Add this new binding as a fallback
if the ports node can't be found.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k internal phy driver require some special debug value to be set
based on the switch revision. Rework the switch id read function to
also read the chip revision.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch qca8327 needs special settings for the GLOBAL_FC_THRES regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit port5 rx delay to qca8337. This is taken from the legacy QSDK code
that limits the rx delay on port5 to only this particular switch version,
on other switch only the tx and rx delay for port0 are needed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port 5 of the qca8337 have some problem in flood condition. The
original legacy driver had some specific buffer and priority settings
for the different port suggested by the QCA switch team. Add this
missing settings to improve switch stability under load condition.
The packet priority tweak is only needed for the qca8337 switch and
other qca8k switch are not affected.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8327 switch is a low tier version of the more recent qca8337.
It does share the same regs used by the qca8k driver and can be
supported with minimal change.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate errors from qca8k_busy_wait instead of hardcoding return
value.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k_rmw can fail. Rework any user to handle error values and
correctly return. Change qca8k_rmw to return the error code or 0 instead
of the reg value. The reg returned by qca8k_rmw wasn't used anywhere,
so this doesn't cause any functional change.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k_write can fail. Rework any user to handle error values and
correctly return.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8k_read can fail. Rework any user to handle error values and
correctly return.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a remote possibility, the set_page function can fail. Since this is
a critical part of the write/read qca8k regs, propagate the error and
terminate any read/write operation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put bus in local variable to improve faster access to the mdio bus.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iopoll macro instead of while loop.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change pr_err and pr_warn to dev variant.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 316bcffe44 ("net: dsa: felix: disable always guard band bit for
TAS config") disabled the guard band and broke 802.3Qbv compliance.
There are two issues here:
(1) Without the guard band the end of the scheduling window could be
overrun by a frame in transit.
(2) Frames that don't fit into a configured window will still be sent.
The reason for both issues is that the switch will schedule the _start_
of a frame transmission inside the predefined window without taking the
length of the frame into account. Thus, we'll need the guard band which
will close the gate early, so that a complete frame can still be sent.
Revert the commit and add a note.
For a lengthy discussion see [1].
[1] https://lore.kernel.org/netdev/c7618025da6723418c56a54fe4683bd7@walle.cc/
Fixes: 316bcffe44 ("net: dsa: felix: disable always guard band bit for TAS config")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_switch_alloc() will return NULL only if allocation is failed. So,
the proper return value is -ENOMEM.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible NULL pointer dereference in case devm_kzalloc() failed to
allocate memory
Fixes: cc13e52c3a ("net: dsa: microchip: Add Microchip KSZ8863 SPI based driver support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible NULL pointer dereference in case devm_kzalloc() failed to
allocate memory.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the for-loop in ksz8_port_init_cnt is causing a static
analysis infinite loop warning with the comparison of
mib->cnt_ptr < dev->reg_mib_cnt. This occurs because mib->cnt_ptr
is a u8 and dev->reg_mib_cnt is an int and the analyzer determines
that mib->cnt_ptr potentially can wrap around to zero if the value
in dev->reg_mib_cnt is > 255. However, this value is never this
large, it is always less than 256 so make reg_mib_cnt a u8.
Addresses-Coverity: ("Infinite loop")
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210428120010.337959-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add KSZ88X3 driver support. We add support for the KXZ88X3 three port
switches using the Microchip SMI Interface. They are supported using the
MDIO-Bitbang Interface.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ88X3 driver support. We add support for the KXZ88X3 three port
switches using the SPI Interface.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add support for the ksz8863 and ksz8873 chips which are
using the same register patterns but other offsets as the
ksz8795.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get this driver used with other switches the functions need
to use different offsets and register shifts. This patch changes the
direct use of the register defines to register description structures,
which can be set depending on the chips register layout.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the cpu interface selection code to a individual
function specific for ksz8795. It will make it simpler to customize the
code path for different switches supported by this driver.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be used on other chips of this type. To reflect
this we rename the drivers prefix from ksz8795 to ksz8.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.
This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was a waste to clone skb directly in dsa_skb_tx_timestamp().
For one-step timestamping, a clone was not needed. For any failure of
port_txtstamp (this may usually happen), the skb clone had to be freed.
So this patch moves skb cloning for tx timestamp out of dsa core, and
let drivers clone skb in port_txtstamp if they really need.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ptp_classify_raw out of dsa core driver for handling tx
timestamp request. Let device drivers do this if they want.
Not all drivers want to limit tx timestamping for only PTP
packet.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check tx timestamp request in core driver at very beginning of
dsa_skb_tx_timestamp(), so that most skbs not requiring tx
timestamp just return. And drop such checking in device drivers.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .serdes_get_lane op used the magic value 0xff to indicate a valid
SERDES lane and 0 signaled that a non-SERDES mode was set on the port.
Unfortunately, "0" is also a valid lane ID, so even when these ports
where configured to e.g. RGMII the driver would set them up as SERDES
ports.
- Replace 0xff with 0 to indicate a valid lane ID. The number is on
the one hand just as arbitrary, but it is at least the first valid one
and therefore less of a surprise.
- Follow the other .serdes_get_lane implementations and return -ENODEV
in the case where no SERDES is assigned to the port.
Fixes: f5be107c33 ("net: dsa: mv88e6xxx: Support serdes ports on MV88E6097/6095/6185")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the raw PVT data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event of the VTU being loaded to the brim with 4k
entries, the last one was placed in the buffer, but the size reported
to devlink was off-by-one. Make sure that the final entry is available
to the caller.
Fixes: ca4d632aef ("net: dsa: mv88e6xxx: Export VTU as devlink region")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because ADRR is not a thing.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For devices that supports both regular and Ethertyped DSA tags, allow
the user to change the protocol.
Additionally, because there are ethernet controllers that do not
handle regular DSA tags in all cases, also allow the protocol to be
changed on devices with undocumented support for EDSA. But, in those
cases, make sure to log the fact that an undocumented feature has been
enabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devices are capable of using regular DSA tags. Support for
Ethertyped DSA tags sort into three categories:
1. No support. Older chips fall into this category.
2. Full support. Datasheet explicitly supports configuring the CPU
port to receive FORWARDs with a DSA tag.
3. Undocumented support. Datasheet lists the configuration from
category 2 as "reserved for future use", but does empirically
behave like a category 2 device.
So, instead of listing the one true protocol that should be used by a
particular chip, specify the level of support for EDSA (support for
regular DSA is implicit on all chips). As before, we use EDSA for all
chips that fully supports it.
In upcoming changes, we will use this information to support
dynamically changing the tag protocol.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amethyst internal PHYs also report empty model number in MII_PHYSID2.
Fill in switch product number, as is done for Topaz and Peridot.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALWAYS_GUARD_BAND_SCH_Q bit in TAS config register is descripted as
this:
0: Guard band is implemented for nonschedule queues to schedule
queues transition.
1: Guard band is implemented for any queue to schedule queue
transition.
The driver set guard band be implemented for any queue to schedule queue
transition before, which will make each GCL time slot reserve a guard
band time that can pass the max SDU frame. Because guard band time could
not be set in tc-taprio now, it will use about 12000ns to pass 1500B max
SDU. This limits each GCL time interval to be more than 12000ns.
This patch change the guard band to be only implemented for nonschedule
queues to schedule queues transition, so that there is no need to reserve
guard band on each GCL. Users can manually add guard band time for each
schedule queues in their configuration if they want.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit fee2d54641 ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d54641 ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three minor changes:
- When disabling PLL, there is no need to call core_write_mmd_indirect
directly, use the core_write wrapper instead like the rest of the code
in the function does. This change helps with consistency and
readability. Move the comment to the definition of
core_read_mmd_indirect where it belongs.
- Disable both core and TRGMII Tx clocks prior to reconfiguring.
Previously, only the core clock was disabled, but not TRGMII Tx clock.
So disable both, then configure them, then re-enable both, for
consistency.
- The core clock enable bit (REG_GSWCK_EN) is written redundantly three
times. Simplify the code and only write the register only once at the
end of clock reconfiguration to enable both core and TRGMII Tx clocks.
Tested on Ubiquiti ER-X running the GMAC0 and MT7530 in TRGMII mode.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the driver name, ASIC ID and the switch name via devlink. This is a
useful information for user space tooling.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify compatible string against hardware.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to use all PHYs on GRX300 and GRX330. The ARX300
has 3 and the GRX330 has 4 integrated PHYs connected to different
ports compared to VRX200. Each integrated PHY can work as single
Gigabit Ethernet PHY (GMII) or as double Fast Ethernet PHY (MII).
Allowed port configurations:
xRX200:
GMAC0: RGMII, MII, REVMII or RMII port
GMAC1: RGMII, MII, REVMII or RMII port
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX300:
GMAC0: RGMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII) or RGMII port
xRX330:
GMAC0: RGMII, GMII or RMII port
GMAC1: GPHY2 (GMII)
GMAC2: GPHY0 (GMII)
GMAC3: GPHY0 (MII) or GPHY3 (GMII)
GMAC4: GPHY1 (GMII)
GMAC5: GPHY1 (MII), RGMII or RMII port
Tested on D-Link DWR966 (xRX330) with OpenWRT.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0b5294483c ("net: dsa: mv88e6xxx: scratch: Fixup kerneldoc")
has addressed some but not all kerneldoc warnings for the Global 2
Scratch register accessors. Namely, we have some mismatches between
the function names in the kerneldoc and the ones in the actual code.
Let's adjust the comments so that they match the functions they're
sitting next to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove CONFIG_HAVE_NET_DSA.
CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers
should have selected CONFIG_NET_DSA manually.
Currently, all drivers has explicit 'depends on NET_DSA', so this is
no more needed.
2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones.
- dropped !S390 dependency which was introduced to be sure NET_DSA
can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years
ago and the PHY library itself doesn't depend on !S390 since
commit 870a2b5e4f ("phylib: remove !S390 dependeny from Kconfig");
- INET dependency is kept to be sure we can select NET_SWITCHDEV;
- NETDEVICES dependency is kept to be sure we can select PHYLINK.
3. DSA drivers menu now depends on NET_DSA.
Instead on 'depends on NET_DSA' on every single driver, the entire
menu now depends on it. This eliminates a lot of duplicated lines
from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can
be only m or n).
This also has a nice side effect that there's no more empty menu on
configurations without DSA.
4. Kbuild will now descend into 'drivers/net/dsa' only when
CONFIG_NET_DSA is y or m.
This is safe since no objects inside this folder can be built without
DSA core, as well as when CONFIG_NET_DSA=m, no objects can be
built-in.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e9bf96943b.
The topic of the reverted patch is the support for switches with global
VLAN filtering, added by commit 061f6a505a ("net: dsa: Add
ndo_vlan_rx_{add, kill}_vid implementation"). Be there a switch with 4
ports swp0 -> swp3, and the following setup:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
ip link set swp1 master br0
What would happen with VLAN-tagged traffic received on standalone ports
swp2 and swp3? Well, it would get dropped, were it not for the
.ndo_vlan_rx_add_vid and .ndo_vlan_rx_kill_vid implementations (called
from vlan_vid_add and vlan_vid_del respectively). Basically, for DSA
switches where VLAN filtering is a global attribute, we enforce the
standalone ports to have 'rx-vlan-filter: off [fixed]' in their ethtool
features, which lets the user know that all VLAN-tagged packets that are
not explicitly added in the RX filtering list are dropped.
As for the sja1105 driver, at the time of the reverted patch, it was
operating in a pretty handicapped mode when it had ports under a bridge
with vlan_filtering=1. Specifically, it was unable to terminate traffic
through the CPU port (for further explanation see "Traffic support" in
Documentation/networking/dsa/sja1105.rst).
However, since then, the sja1105 driver has made considerable progress,
and that limitation is no longer as severe now. Specifically, since
commit 2cafa72e51 ("net: dsa: sja1105: add a new
best_effort_vlan_filtering devlink parameter"), the driver is able to
perform CPU termination even when some ports are under bridges with
vlan_filtering=1. Then, since commit 8841f6e63f ("net: dsa: sja1105:
make devlink property best_effort_vlan_filtering true by default"), this
even became the default operating mode.
So we can now take advantage of the logic in the DSA core.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These switches have two modes of classifying broadcast:
1. Broadcast is multicast.
2. Broadcast is its own unique thing that is always flooded
everywhere.
This driver uses the first option, making sure to load the broadcast
address into all active databases. Because of this, we can support
per-port broadcast flooding by (1) making sure to only set the subset
of ports that have it enabled whenever joining a new bridge or VLAN,
and (2) by updating all active databases whenever the setting is
changed on a port.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to control automatic learning per port.
Many chips have an explicit "LearningDisable"-bit that can be used for
this, but we opt for setting/clearing the PAV instead, as it works on
all devices at least as far back as 6083.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In accordance with the comment in dsa_port_bridge_leave, standalone
ports shall be configured to flood all types of traffic. This change
aligns the mv88e6xxx driver with that policy.
Previously a standalone port would initially not egress any unknown
traffic, but after joining and then leaving a bridge, it would.
This does not matter that much since we only ever send FROM_CPUs on
standalone ports, but it seems prudent to make sure that the initial
values match those that are applied after a bridging/unbridging cycle.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the conventional declaration style of a MAC address in the
kernel (u8 addr[ETH_ALEN]) for the broadcast address, then set it
using the existing helper.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has a somewhat quirky protocol for reading out the VTU
entry for a particular VID. But there is no reason why we cannot
create a better API for ourselves in the driver.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the intricacies of correctly iterating over the VTU to a common
implementation.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is a part of a LAG, the ATU will create dynamic entries
belonging to the LAG ID when learning is enabled. So trying to
fast-age those out using the constituent port will have no
effect. Unfortunately the hardware does not support move operations on
LAGs so there is no obvious way to transform the request to target the
LAG instead.
Instead we document this known limitation and at least avoid wasting
any time on it.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM4908 has only 1 RGMII reg for controlling port 7.
Fixes: 73b7a60479 ("net: dsa: bcm_sf2: support BCM4908's integrated switch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple macro like REG_RGMII_CNTRL_P() is insufficient as:
1. It doesn't validate port argument
2. It doesn't support chipsets with non-lineral RGMII regs layout
Missing port validation could result in getting register offset from out
of array. Random memory -> random offset -> random reads/writes. It
affected e.g. BCM4908 for REG_RGMII_CNTRL_P(7).
Fixes: a78e86ed58 ("net: dsa: bcm_sf2: Prepare for different register layouts")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree support to b53_mmap.c while keeping platform devices support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16-bit Port Policy CTL register from older chips is on 6393x changed
to Port Policy MGMT CTL, which can access more data, but indirectly and
via 8-bit registers.
The original 16-bit value is divided into first two 8-bit register in
the Port Policy MGMT CTL.
We can therefore use the previous code to compute the mask and shift,
and then
- if 0 <= shift < 8, we access register 0 in Port Policy MGMT CTL
- if 8 <= shift < 16, we access register 1 in Port Policy MGMT CTL
There are in fact other possible policy settings for Amethyst which
could be added here, but this can be done in the future.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6393X device is a single-chip integration of a 11-port
Ethernet switch with eight integrated Gigabit Ethernet (GbE)
transceivers and three 10-Gigabit interfaces.
This patch adds functionalities specific to mv88e6393x family (88E6393X,
88E6193X and 88E6191X).
The main differences between previous devices and this one are:
- port 0 can be a SERDES port
- all SERDESes are one-lane, eg. no XAUI nor RXAUI
- on the other hand the SERDESes can do USXGMII, 10GBASER and 5GBASER
(on 6191X only one SERDES is capable of more than 1g; USXGMII is not
yet supported with this change)
- Port Policy CTL register is changed to Port Policy MGMT CTL register,
via which several more registers can be accessed indirectly
- egress monitor port is configured differently
- ingress monitor/CPU/mirror ports are configured differently and can be
configured per port (ie. each port can have different ingress monitor
port, for example)
- port speed AltBit works differently than previously
- PHY registers can be also accessed via MDIO address 0x18 and 0x19
(on previous devices they could be accessed only via Global 2 offsets
0x18 and 0x19, which means two indirections; this feature is not yet
leveraged with thiis commit)
Co-developed-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Ashkan Boldaji <ashkan.boldaji@digi.com>
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Co-developed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two implementations of the .set_egress_port method, and both
of them, if successful, set chip->*gress_dest_port variable.
To avoid code repetition, wrap this method into
mv88e6xxx_set_egress_port.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 is no more an error case with MV88E6393 family
which has serdes lane numbers 0, 9 or 10.
So with this change .serdes_get_lane will return lane number
or -errno (-ENODEV or -EOPNOTSUPP).
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tags are used on BCM5325, BCM5365 and BCM63xx switches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM63xx switches are present on bcm63xx and bmips devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support port MDB and bridge flag operations.
As the hardware can manage multicast forwarding itself, offload_fwd_mark
can be unconditionally set to true.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
