[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A comparison error made it possible to not iterate through all the
specified prefetch modes.
[how]
Correct "<" to "<="
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Yongqiang Sun <Yongqiang.Sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During headless boot, DIG may be on which causes HW/SW discrepancies.
To avoid this we power down hardware on boot if DIG is turned on. With
introduction of multiple eDP, hardware power down is being bypassed
under certain conditions.
[How]
Fixed hardware power down bypass, and ensured hardware will power down
if DIG is on and seamless boot is not enabled.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Theoretically, per DP 1.4a spec, sink device needs to AUX_ACK 00340h
write. However, due to hardware limitation, some sink devices have no
00340h dpcd address at all. This results in sink side fails to reply
ACK, and consequently cause source side keep retrying DPCD write on DPCD
00340h. This results in significant delay when DPCD 00340h write is
triggered (e.g. at S3 resume).
[How]
Check whether sink device could ACK on DPCD 00340h write on boot. If
sink device fails to ACK, then remember that, so we won't write to DPCD
00340h later on.
There will be a drm.debug KMS level message to inform user once a 00340h
DPCD write is skipped on purpose.
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Print a debug message when dcc validation fails in the display driver.
Most DCC enablement related errors are from userspace. Adding a debug
print in case of a failure from display driver will aid quicker triage.
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Regression found in some embedded panels traces back to the earliest
upstreamed ASSR patch. The changed code flow are causing problems
with some panels.
[How]
- Change ASSR enabling code while preserving original code flow
as much as possible
- Simplify the code on guarding with internal display flag
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213779
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1620
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Populate dtbclk values from bwparams for dcn302, dcn303.
[How]
dtbclk values are fetched from bandwidthparams for all DPM levels and
for DPM levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN31 doesn't have MALL in DMUB so to avoid sending unknown commands to
DMUB just remove the function pointer.
[how]
Remove apply_idle_power_optimizations from function pointers structure
for DCN31
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We're missing a default value for dram_channel_width_bytes in the
DCN3.1 SOC bounding box and we don't currently have the interface in
place to query the actual value from VBIOS.
Put in a hardcoded default until we have the interface in place.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.
In the case where the hardcode is also missing we can't lightup display.
[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Initialize socclk entries in bandwidth params for dcn302, dcn303.
[How]
Fetch the sockclk values from smu for the DPM levels and for the DPM
levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vertical and horizontal borders in timings are treated as increasing the
active area - vblank and hblank actually shrink.
Our input into DML does not include these borders so it incorrectly
assumes it has more time than available for vstartup and tmdl
calculations for some modes with borders.
An example of such a timing would be 640x480@72Hz:
h_total: 832
h_border_left: 8
h_addressable: 640
h_border_right: 8
h_front_porch: 16
h_sync_width: 40
v_total: 520
v_border_top: 8
v_addressable: 480
v_border_bottom: 8
v_front_porch: 1
v_sync_width: 3
pix_clk_100hz: 315000
[How]
Include borders as part of destination vactive/hactive.
This change DCN20+ so it has wide impact, but the destination vactive
and hactive are only really used for vstartup calculation anyway.
Most modes do not have vertical or horizontal borders.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A comparison error made it possible to not iterate through all the
specified prefetch modes.
[how]
Correct "<" to "<="
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Yongqiang Sun <Yongqiang.Sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add reserved bits for future feature development
- Fix issue with mismatch with type const
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This tends to take miliseconds in certain scenarios and we'd rather not
wait that long. Due to how this interacts with det size update and
locking waiting should not be necessary as compbuf updates before
unlock.
Add a watch for config error instead as that is something we actually do
care about.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reserve padding bytes for new feature implementation
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Extend existing state collection functions to add some additional
registers useful for debug, and add state collection function for DC
hubbub
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Lowering clocks when entering S2 Idle state causes DMUB to hang with
Diags.
[how]
Do not enter S2 optimization with Diags on dcn301 to prevent DMUB hang.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The units of the time_per_pixel variable were incorrect, this had to be
changed for the code to properly function.
[how]
The change was very straightforward, only required one line of code to
be changed where the calculation was done.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current logic checks if there's an upper pipe whose viewport
completely covers the current pipe viewport.
This fails in pipe splitting case as you can have layer 1 pipe that
crosses the two layer 0 pipes where it's contained in both, but neither
covers it completely, hence we allow the cursor on both layers.
[How]
Instead of trying to "sum up" rectangles from the higher level pipes
which could leave gaps and would not work generically, we will assume if
there's an upper layer that is active, it will control the HW cursor.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
currently dc has never reset this dpcd_cap.dpcd_rev.
[how]
ideally we should reset this before redo detection.
change the passive dongle only for now to reduce the impact.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 72a7cf0aec ("drm/amd/display: Keep linebuffer pixel depth at
30bpp for DCE-11.0.") doesn't seems to have fixed 10bit 4K rendering over
DisplayPort for CIK GPUs. On my machine with a HAWAII GPU I get a broken
image that looks like it has an effective resolution of 1920x1080 but
scaled up in an irregular way. Reverting the commit or applying this
patch fixes the problem on v5.14-rc1.
Fixes: 72a7cf0aec ("drm/amd/display: Keep linebuffer pixel depth at 30bpp for DCE-11.0.")
Acked-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 72a7cf0aec ("drm/amd/display: Keep linebuffer pixel depth at
30bpp for DCE-11.0.") doesn't seems to have fixed 10bit 4K rendering over
DisplayPort for CIK GPUs. On my machine with a HAWAII GPU I get a broken
image that looks like it has an effective resolution of 1920x1080 but
scaled up in an irregular way. Reverting the commit or applying this
patch fixes the problem on v5.14-rc1.
Fixes: 72a7cf0aec ("drm/amd/display: Keep linebuffer pixel depth at 30bpp for DCE-11.0.")
Acked-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't populate the const array common_rates on the stack but instead it
static. Makes the object code smaller by 80 bytes:
Before:
text data bss dec hex filename
268019 98322 256 366597 59805 ../display/amdgpu_dm/amdgpu_dm.o
After:
text data bss dec hex filename
267843 98418 256 366517 597b5 ../display/amdgpu_dm/amdgpu_dm.o
Reduction of 80 bytes
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the unknown CEA parse case on DMUB-enabled ASICs, dmesg will
print an error message like below, this will be captured by
automation tools as it has the word like ERROR during boot up
and treated as a false error, as it does not break bootup process.
So use DRM_WARN printing for this.
[drm:amdgpu_dm_update_freesync_caps [amdgpu]] *ERROR* Unknown EDID CEA parser results
v2: Use DRM_WARN to print such info.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The original logic is to update eDP's backlight level
on every amdgpu dm atomic commit, which causes excessive
DMUB write. As a result, when playing game or moving window
around, DMUB timeout and system lagging are observed.
[How]
We only need to update eDP's backlight level when current level
doesn't match requested level.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 2b7605d73b
Some displays are not lighting up when put in LTTPR Transparent Mode
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
We're only treating TMDS as a valid target for infoframe updates which
results in PSR being unable to transition from state 4 to state 5.
[How]
Also allow infoframe updates for DCN3.1 - following how we handle
this path for earlier ASIC as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The original logic is to update eDP's backlight level
on every amdgpu dm atomic commit, which causes excessive
DMUB write. As a result, when playing game or moving window
around, DMUB timeout and system lagging are observed.
[How]
We only need to update eDP's backlight level when current level
doesn't match requested level.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
EDID CTS requires at least 2k (16 blocks) to be readable.
[How]
Increase EDID buffer size to 2k
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When requesting clocks from SMU which takes MHz inputs, DC will round
down KHz when converting to MHz, thus potentially requesting too low a
clock value.
[How]
Round up (ceil) when converting KHz to MHz for clock requests to SMU.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Updated SCR definition for FW boot options for Separate DCN init
for DMUB FW loaded in VBL
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Type adjustments and formatting fixes.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 2b7605d73b
Some displays are not lighting up when put in LTTPR Transparent Mode
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're only treating TMDS as a valid target for infoframe updates which
results in PSR being unable to transition from state 4 to state 5.
[How]
Also allow infoframe updates for DCN3.1 - following how we handle
this path for earlier ASIC as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changes in DM needed to support Freesync HDMI on DMUB.
[How]
Change implementation to parse CEA blocks in case of DMUB-enabled ASICs.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added NULL checks before two problematic statements
Signed-off-by: Wang <anguwang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dmub would notify x86 response time violation by GPINT_DATAOUT
[How]
1. Use GPINT_DATAOUT to trigger x86 interrupt
2. Register GPINT_DATAOUT interrupt handler.
3. Trigger ACR while GPINT_DATAOUT occurred.
Signed-off-by: Chun-Liang Chang <Chun-Liang.Chang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a difference between our default behavior and override
behavior. For default behavior we need to decide link training settings
within specs' limitation and mandates.
For override behavior we do not need to follow all these requirements.
We are isolating override decision to its own function to maintain the
integrity of our specs compliant default behavior.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Extend existing support for DCN2.1 DMUB diagnostic logging to
DCN3.1 so we can collect useful information if the DMUB hangs.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Setting CONFIG_FRAME_WARN=0 should disable 'stack frame larger than'
warnings. This is useful for example in KASAN builds. Make the dml
Makefile respect this config.
Fixes the following build warnings with CONFIG_KASAN=y and
CONFIG_FRAME_WARN=0:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn30/display_mode_vba_30.c:3642:6:
warning: stack frame size of 2216 bytes in function
'dml30_ModeSupportAndSystemConfigurationFull' [-Wframe-larger-than=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn31/display_mode_vba_31.c:3957:6:
warning: stack frame size of 2568 bytes in function
'dml31_ModeSupportAndSystemConfigurationFull' [-Wframe-larger-than=]
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Reka Norman <rekanorman@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also copy over the part that makes old gcc handling cross-platform.
Fixes: df7a1658f2 ("drm/amdgpu/dc: fix DCN3.1 Makefile for PPC64")
Fixes: 926d6972ef ("drm/amd/display: Add DCN3.1 blocks to the DC Makefile")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During GPU reset, when receiving a DMCUB OUTBUX0 interrupt,
DAL code will set it to be OUTBOX interrupt and sets hw interrupt.
However, OUTBOX interrupt is not registered yet, so a NULL pointer
access will be executed.
Call Trace:
dal_irq_service_set+0x30/0x90 [amdgpu]
dc_interrupt_set+0x24/0x30 [amdgpu]
amdgpu_dm_set_dmub_outbox_irq_state+0x22/0x30 [amdgpu]
amdgpu_irq_update+0x77/0xa0 [amdgpu]
amdgpu_irq_gpu_reset_resume_helper+0x67/0xa0 [amdgpu]
amdgpu_do_asic_reset+0x219/0x260 [amdgpu]
amdgpu_device_gpu_recover.cold+0x8c5/0xb64 [amdgpu]
amdgpu_debugfs_gpu_recover_show+0x2c/0x60 [amdgpu]
seq_read_iter+0xc2/0x450
? do_anonymous_page+0x22c/0x3b0
seq_read+0xf9/0x140
full_proxy_read+0x5c/0x90
vfs_read+0xaa/0x190
ksys_read+0x67/0xe0
__x64_sys_read+0x1a/0x20
Fixes: effbf6ca7e ("drm/amdgpu/display: remove an old DCN3 guard")
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-and-tested-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
valid DAL irq should be < DAL_IRQ_SOURCES_NUMBER.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-and-tested-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit 33f409e60e.
The patch that we are reverting here was originally applied because it
fixes multiple IGT issues and flickering in Android. However, after a
discussion with Sean Paul and Mark, it looks like that this patch might
cause problems on ChromeOS. For this reason, we decided to revert this
patch.
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Mark Yacoub <markyacoub@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Sometimes, DP receiver chip power-controlled externally by an
Embedded Controller could be treated and used as eDP,
if it drives mobile display. In this case,
we shouldn't be doing power-sequencing, hence we can skip
waiting for T7-ready and T9-ready."
[How]
Added a feature mask to enable eDP no power sequencing feature.
To enable this, set 0x10 flag in amdgpu.dcfeaturemask on
Linux command line.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Introduce CMD for EDID CEA block parsing
- Add SCR5 definition for reporting eDP power sequencer status
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Increase width of some variables to avoid comparing integers of
different widths
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Updating the file to fix the missing line
Signed-off-by: Logush Oliver <ollogush@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
recent VBIOS dce_infotable reference clock change caused a I2c regression.
instead of relying on vbios, let's get it from HW directly.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After panel power up, if PSR entry attempted too early,
PSR state may get stuck in transition.
This could happen if the panel is not ready
to respond to the SDP PSR entry message.
In this case dmub f/w is unable to abort PSR entry
since abortion is not permitted after the SDP has been sent.
[How]
Skip 5 pageflips before PSR enable.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some SOC BB paramters may vary per SKU, and it does
not make sense for driver to hardcode these values.
This change was added for dcn30 and dcn301, but not
for dcn302 and dcn303
[how]
Parse the values from VBIOS if available, and use
them if valid
Fixes: 93669c8e48 ("drm/amd/display: get socBB from VBIOS")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
extended_end_address can only be calculated from the extended_address and
extended_size
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The voltage swing has to start from the minimum level when transmit TPS1 over
Main-Link in clock recovery sequence.
The lane settings from current design will inherit the existing VS/PE values
that could be adjusted by Repeater X, and to use the adjusted voltage swing level
in Repeater X-1 or DPRX could violate DP specs.
[How]
To reset VS from lane settings after LTTPRs have been trained to meet the requirement.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some timings with a large VBlank cause the value to overflow the
register related, while also producing other wrong values in DML output.
[how]
Clamp VStartup at the DCN3.1 maximum value
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When video plane is rotate the cursor position is incorrect and not
matching the desktop location.
[How]
When a plane is rotated 90 or 270 degrees, the src_rect.width and height
should be swapped when determining the scaling factor compared to the
dst_rect.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dml/dcn31/display_rq_dlg_calc_31.c:
55:12-42: duplicated argument to && or ||
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Function 'dpp1_full_bypass' is declared twice, so remove the repeated
declaration and unnessary blank line.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix
the following warning by replacing a /* fall through */ comment
with the new pseudo-keyword macro fallthrough:
rivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:672:4: warning: unannotated fall-through between switch labels [-Wimplicit-fallthrough]
case AUX_TRANSACTION_REPLY_I2C_OVER_AUX_DEFER:
^
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings, so in order to globally enable
-Wimplicit-fallthrough for Clang, these comments need to be
replaced with fallthrough; in the whole codebase.
Link: https://github.com/KSPP/linux/issues/115
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GCC reports the following warning with W=1:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_psr.c:70:13:
warning:
variable ‘dc’ set but not used [-Wunused-but-set-variable]
70 | struct dc *dc = NULL;
| ^~
This variable is not used in function, this commit remove it to
fix the warning.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GCC reports the following warning with W=1:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:3635:17:
warning:
variable ‘status’ set but not used [-Wunused-but-set-variable]
3635 | enum dc_status status = DC_ERROR_UNEXPECTED;
| ^~~~~~
The variable should be used for error check, let's fix it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Recently, we added support for an experimental feature named Freesync
video; for more details on that, refer to:
commit 6f59f229f8 ("drm/amd/display: Skip modeset for front porch change")
commit d10cd527f5 ("drm/amd/display: Add freesync video modes based on preferred modes")
commit 0eb1af2e82 ("drm/amd/display: Add module parameter for freesync video mode")
Nevertheless, we did not document it in detail in our driver. This
commit introduces a kernel-doc and expands the module parameter
description.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current watermarks end up programming lowers watermarks which
results in screen flickering and underflow for certain modes like 1440p.
[How]
Add 11us to stutter exit & stutter enter plus exit watermark.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn31/dcn31_resource.c:917:56-57:
pstate_enabled: first occurrence line 935, second occurrence line 937
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP LL Compliance tests require that the first DPCD transactions after a
hotplug have a timeout interval of 3.2 ms. In cases where LTTPR is
disabled, this means that the first reads from DP_SET_POWER and DP_DPCD_REV must have an extended
timeout.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When changing the DISPCLK_WDIVIDER value from 126 to 127, the change in
clock rate is too great for the FIFOs to handle. This can cause visible
corruption during clock change.
HW has handed down this register sequence to fix the issue.
[HOW]
The sequence, from HW:
a. 127 -> 126
Read DIG_FIFO_CAL_AVERAGE_LEVEL
FIFO level N = DIG_FIFO_CAL_AVERAGE_LEVEL / 4
Set DCCG_FIFO_ERRDET_OVR_EN = 1
Write 1 to OTGx_DROP_PIXEL for (N-4) times
Set DCCG_FIFO_ERRDET_OVR_EN = 0
Write DENTIST_DISPCLK_RDIVIDER = 126
Because of frequency stepping, sequence a can be executed to change the
divider from 127 to any other divider value.
b. 126 -> 127
Read DIG_FIFO_CAL_AVERAGE_LEVEL
FIFO level N = DIG_FIFO_CAL_AVERAGE_LEVEL / 4
Set DCCG_FIFO_ERRDET_OVR_EN = 1
Write 1 to OTGx_ADD_PIXEL for (12-N) times
Set DCCG_FIFO_ERRDET_OVR_EN = 0
Write DENTIST_DISPCLK_RDIVIDER = 127
Because of frequency stepping, divider must first be set from any other
divider value to 126 before executing sequence b.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware has handed down a new sequence requiring the value of this
register be read from clk_mgr.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 spec says that multiple LTTPRs must not be accessed in a
single AUX transaction.
There may be other places in future where breaking up AUX accesses is
necessary.
[HOW]
Partition the entire DPCD address space into blocks. When an incoming AUX
request spans multiple blocks, break up the request into multiple requests.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP 2.0 SCR specifies that
"A DPTX shall distinguish I2C_DEFER|AUX_ACK from AUX_DEFER. AUX retries
due to
I2C_DEFER are not counted as part of minimum 7 retires (sic) upon
AUX_DEFER’s"
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP 2.0 SCR specifies that TX devices must retry at least 7 times when
receiving an AUX DEFER reply from RX. In addition, the specification
states that the TX shall not retry indefinitely, and gives a suggestive
timeout interval of 50ms.
[HOW]
Keep retrying until both 7 or more retries have been made, and the 50ms
interval has passed.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
7 is the minimum number of retries TX must attempt on an AUX DEFER, not
the maximum.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some DPCD addresses, notably LTTPR Capability registers, are expected to
be read all together in a single DPCD transaction. Rather than force callers to
read registers they don't need, we want to quietly extend the addresses
read, and only return back the values the caller asked for.
This does not affect DPCD writes.
[HOW]
Create an additional layer above AUX to perform 'checked' DPCD
transactions.
Iterate through an array of DPCD address ranges that are marked as being
contiguous. If a requested read falls within one of those ranges, extend
the read to include the entire range.
After DPCD has been queried, copy the requested bytes into the caller's
data buffer, and deallocate all resources used.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DP specifies that an LTTPR device is only present if PHY_REPEATER_CNT is
0x80, 0x40, 0x20, 0x10, 0x08, 0x04, 0x02, or 0x01.
All other values should be considered no LTTPRs present.
[HOW]
Function dp_convert_to_count already does this check. Use it to determine
if PHY_REPEATER_CNT is a valid LTTPR count.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP2.0 requires that LT be performed with PHY_REPEATER_MODE
programmed to 0x55 (Transparent) whenever PHY_REPEATER_CNT is any value
other than 0x80, 0x40, 0x20, 0x10, 0x08, 0x04, 0x02, or 0x01.
[HOW]
Write Non-Transparent (0xAA) to PHY_REPEATER_MODE when LTTPRs detected and Non-Transparent is
requested.
Write Transparent in all other cases.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 Spec states that a DPTX shall put LTTPRs into Transparent
mode after reading LTTPR Capability registers on HPD.
The wording of the SCR is somewhat ambiguous as to whether
Transparent mode must be set explicity, or is implicitly set on LTTPR
capability read. Explicitly setting Transparent mode after LTTPR
capability read should cover all
cases.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 requires that LTTPR caps be read first on hotplug.
For the sake of consistency, this should also be the case on bootup.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want LTTPR capabilities to be readable from more places than just
retrieve_link_cap
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
A new SCR for the DP2.0 spec requires that LTTPR caps be the first thing
read from DPCD upon hotplug.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Improve the maintain/read abilities of dm code.
[How]
Create amdgpu_dm_psr.c/h files.
Move psr function from amdgpu_dm.c
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixed:
- LTTPR improvements
- Backlight improvements
- eDP hotplug detection
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To change the swizzle visual confirm reference pipe from top pipe to
bottom pipe due to bottom pipe information would be more important
for multiple overlay case.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move mst start top mgr in dc_link_detect layer.
Remove unused same_dpcd variable.
Move PEAK_FACTOR_X1000 and LINK_TRAINING_MAX_VERIFY_RETRY
to the proper header for defining dc link internal constant.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Tune backlight ramping profiles for each Vari-Bright level to suit
customer preferences
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some custom platforms use eDP hotplug events to notify panel
capability changes that should be reported
[How]
Add a DC config option that unblocks eDP hotplug events
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Ability to triage DMCUB is improved with availability of certain
dmub registers not currently captured in crash dump diagnostic data.
[HOW]
Add dmub registers to diagnostic data collection.
Thanks Nicholas Kazlauskas for awesome input on this!
Signed-off-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For each CRTC state, check the size of Gamma and Degamma LUTs so
unexpected and larger sizes wouldn't slip through.
TEST: IGT:kms_color::pipe-invalid-gamma-lut-sizes
v2: fix assignments in if clauses, Mark's email.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
PG registers are absent in beige goby, so programming these registers
generate call trace. Fix this by adding a dummy function in dcn303
initialization function which prevents writing to non existant registers.
Fixes: cd6d421e3d ("drm/amd/display: Initial DC support for Beige Goby")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/dml/dcn31/display_mode_vba_31.c:
3539:12-42: duplicated argument to && or ||
./drivers/gpu/drm/amd/display/dc/dml/dcn31/display_mode_vba_31.c:
5677:87-123: duplicated argument to && or ||
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use ARRAY_SIZE instead of dividing sizeof array with sizeof an
element.
Clean up the following coccicheck warning:
./drivers/gpu/drm/amd/display/dc/core/dc_resource.c:448:47-48: WARNING:
Use ARRAY_SIZE.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up the following includecheck warning:
./drivers/gpu/drm/amd/display/dc/dcn31/dcn31_hwseq.c: clk_mgr.h is
included more than once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support a new visual confirm mode: swizzle to show the specific
color at the screen border according to different surface swizzle mode.
Currently we only support the Linear mode with red color.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
- Commit from userspace could cause link stream to disable and hdcp
auth to reset when the HDCP has already been enabled at the moment.
CP should fall back to DESIRED from ENABLED in such cases.
- This change was previously reverted due to a regression caused, which
has now been cleared.
[HOW]
In hdcp display removal, change CP to DESIRED if at the moment CP
is ENABLED before the auth reset and removal of linked list element.
Signed-off-by: Dingchen (David) Zhang <dingchen.zhang@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is an assert in cases where transition from ODM 2:1
to ODM 1:1 (bypass)
[How]
Remove assert since this case is now valid.
Update diags tests for ODM transitions.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Found a use case (IPKVM) that DP-VGA active dongle does
not return any EDID and the mentioned commit broke it.
[How]
This reverts "Disconnect non-DP with no EDID"
Signed-off-by: Roy Chan <roy.chan@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add debugfs entry to force dsc decoding at PCON when DSC capable
external RX is connected. In such case, it is free to test DSC
decoding at external RX or at PCON.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When calculating recout width for an MPO plane on a mode that's using
ODM combine, driver can calculate a negative value, resulting in a
crash.
[How]
For negative widths, use zero such that validation will prune the
configuration correctly and disallow MPO.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For DCN30 and later, there is no data in DML arrays indexed by state at
index num_states.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DISPCLK_MAX_ERRDET_CYCLES must be 7 to prevent connection loss when
changing DENTIST_DISPCLK_WDIVIDER from 126 to 127 and back.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence that requires access to these
registers.
v2: squash in DCN3.1 fixes (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence which requires access to the FIFO
ERRDET SW Override register.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Rearranging pipes with multiple displays and multiple planes cannot be
done atomically and requires a much improved sequence to deal with it.
[How]
To workaround such issues, prefer avoid pipe-split policy for
multidisplay scenarios.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When OS overrides training link training parameters
for MST device to SST mode, MST resources are not
released and leak of the resource may result crash and
incorrect MST discovery during following hot plugs.
[how]
Retaining sink object to be reused by SST link and
releasing MST resources.
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Allow specifying which panel to take PSR Residency
measurements from.
[how]
Pass panel instance to DMUB through GPINT in the upper
8 bits of the parameter.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Add call to get the last used VTOTAL from DC
Signed-off-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
SET_CONFIG transactions with DMUB is not used and removed.
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We update scaling settings when scaling mode has been changed.
However when changing mode from native resolution the scaling mode previously
set gets ignored.
[How]
Perform scaling settings update on modeset.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add support for transmitting training pattern sequences for links whose
encoders have been dynamically assigned.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP equalization phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change was found to break some high-refresh modes. Reverting
to unblock mainline.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently there is no way to visually identify if there is one or more
layers presented fullscreen on the display
[HOW]
Add new visual confirm colors in get_surface_visual_confirm_color for
planes with layer_index > 0
Signed-off-by: Evgenii Krasnikov <Evgenii.Krasnikov@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why + How]
Visual confirm has no asic-specific logic,
so we can refactor and unify these functions
that are currently spread out across multiple
dcn files.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
This will allow visual confirm to updated independently
of MPCC blending updates.
v2: squash in DCN3.1 fixes
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This disablement would be specific for Nav10 and shouldn’t be propagated to the other programs.
[How]
Power gating is controlled by driver.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSCCLK validation is not necessary because DSCCLK is derrived from
DISPCLK, therefore if DISPCLK validation passes, DSCCLK is valid, too.
Doing DSCLK validation in addition to DISPCLK leads to modes being
wrongly rejected when DSCCLK was incorrectly set outside of DML.
[how]
Remove DSCCLK validation because it's implicitly validated under DISPCLK
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some DPRX will issue CP_IRQ when user disconnects a display
that has been authenticated.
Since display is being disconnecting dpcd read will fail.
This will cause us to attempt HDCP retry on disconnection.
We are adding a 100ms delay before retry.
So we will only start retry if within 100ms there is no disconnection call
to HDCP module.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Updating PSR interfaces to allow PSR enablement
per eDP panel.
[how]
- Copying PSR command structures to DC
- Changing function interfaces to pass panel instance
- Communicating with DMUB per link instead of assuming
to use a single one
-Iterating through all PSR capable panels when enabling/disabling
all
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DCC on/off, stutter period is calculated before DCC has fully transitioned.
This results in incorrect stutter period calculation.
[How]
Trigger a full update when DCC changes between on/off.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two spelling mistakes in dml_print messages, fix these and
clear up checkpatch warning on overly wide line length.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up the following includecheck warning:
./drivers/gpu/drm/amd/display/dc/dce110/dce110_hw_sequencer.c:
dce110_hw_sequencer.h is included more than once.
No functional change.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The functions can be called both in _rcu context as well
as while holding the lock.
v2: add some kerneldoc as suggested by Daniel
v3: fix indentation
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210602111714.212426-7-christian.koenig@amd.com
Port the necessary changes from previous DCN versions.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
