Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.15 kernel cycle, no
core changes at all this time, just driver work!
New drivers:
- New subdriver for Intel Keem Bay (an ARM-based SoC)
- New subdriver for Qualcomm MDM9607 and SM6115
- New subdriver for ST Microelectronics STM32MP135
- New subdriver for Freescale i.MX8ULP ("Ultra Low Power")
- New subdriver for Ingenic X2100
- Support for Qualcomm PMC8180, PMC8180C, SA8155p-adp PMIC GPIO
- Support Samsung Exynos850
- Support Renesas RZ/G2L
Enhancements:
- A major refactoring of the Rockchip driver, breaking part of it out
to a separate GPIO driver in drivers/gpio
- Pin bias support on Renesas r8a77995
- Add SCI pins support to Ingenic JZ4755 and JZ4760
- Mediatek device tree bindings converted to YAML"
* tag 'pinctrl-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (53 commits)
pinctrl: renesas: Add RZ/G2L pin and gpio controller driver
pinctrl: samsung: Add Exynos850 SoC specific data
dt-bindings: pinctrl: samsung: Add Exynos850 doc
MAINTAINERS: Add maintainers for amd-pinctrl driver
pinctrl: Add Intel Keem Bay pinctrl driver
dt-bindings: pinctrl: Add bindings for Intel Keembay pinctrl driver
pinctrl: zynqmp: Drop pinctrl_unregister for devm_ registered device
dt-bindings: pinctrl: qcom-pmic-gpio: Remove the interrupts property
dt-bindings: pinctrl: qcom-pmic-gpio: Convert qcom pmic gpio bindings to YAML
dt-bindings: pinctrl: mt8195: Use real world values for drive-strength arguments
dt-bindings: mediatek: convert pinctrl to yaml
arm: dts: mt8183: Move pinfunc to include/dt-bindings/pinctrl
arm: dts: mt8135: Move pinfunc to include/dt-bindings/pinctrl
pinctrl: ingenic: Add .max_register in regmap_config
pinctrl: ingenic: Fix bias config for X2000(E)
pinctrl: ingenic: Fix incorrect pull up/down info
pinctrl: Ingenic: Add pinctrl driver for X2100.
dt-bindings: pinctrl: Add bindings for Ingenic X2100.
pinctrl: Ingenic: Add SSI pins support for JZ4755 and JZ4760.
pinctrl: Ingenic: Improve the code.
...
Pull ARM SoC DT updates from Arnd Bergmann:
"As usual, the bulk of work in the SoC tree goes into DT files, this
time with a roughly even split between 32-bit and 64-bit SoCs rather
than the usual mostly 64-bit changes.
New SoCs:
- Microchip SAMA7 SoC family based on Cortex-A7, a new 32-bit
platform based on the older SAMA5 series.
- Qualcomm Snapdragon SDM636 and SM8150, variations of the existing
phone SoCs.
- Renesas R-Car H3e-2G and M3e-2G SoCs, variations of older Renesas
SoCs.
New boards:
- Marvell CN913x reference boards
- ASpeed AST2600 BMC implementations for Facebook Cloudripper, Elbert
and Fuji server boards.
- Snapdragon 665 based Sony Xperia 10II
- Snapdragon MSM8916 based Xiaomi Redmi 2
- Snapdragon MSM8226 based Samsung Galaxy S3 Neo
- NXP i.MX based 32-bit boards:
- DHCOM based PicoITX
- DHSOM based DRC0ỉ
- SolidRun SolidSense
- SKOV i.MX6 boards.
- NXP i.MX based 64-bit boards:
- Nitrogen8 SoM and MNT Reform2
- LS1088A based Traverse Ten64
- i.MX8M based GW7902.
- NVIDIA Jetson TX2 NX Developer Kit
- 4KOpen STiH418-b2264 development board
- ux500 based Samsung phones: Gavini, Codina and Kyle
- TI AM335x based Sancloud BBE Lite
- ixp4xx dts files to replace all old board files
Other changes:
- Treewide fixes for dtc warnings
- Rockchips i/o domain support
- TI OMAP/AM3 CPSW switch driver support
- Improved device support for allwinner, aspeed, qualcomm, NXP,
nvidia, Renesas, Samsung, Amlogic, Mediatek, ixp4xx, stm32, sti,
OMAP and actions"
* tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (412 commits)
arm/arm64: dts: Fix remaining dtc 'unit_address_format' warnings
ARM: dts: rockchip: Add SFC to RV1108
arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
ARM: dts: aspeed: p10bmc: Add power control pins
ARM: dts: aspeed: cloudripper: Add comments for "mdio1"
ARM: dts: aspeed: minipack: Update flash partition table
dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board
dt-bindings: vendor-prefixes: add Traverse Technologies
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
arm64: dts: ls1088a: add missing PMU node
arm64: dts: ls1088a: add internal PCS for DPMAC1 node
ARM: dts: imx6qp-prtwd3: configure ENET_REF clock to 125MHz
ARM: dts: vf610-zii-dev-rev-b: Remove #address-cells and #size-cells property from at93c46d dt node
ARM: dts: add SKOV imx6q and imx6dl based boards
dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
arm64: dts: imx8mq-reform2: add sound support
arm64: dts: imx8m: drop interrupt-affinity for pmu
arm64: dts: imx8qxp: update pmu compatible
arm64: dts: imx8mm: update pmu compatible
...
Pull drm updates from Dave Airlie:
"Highlights:
- i915 has seen a lot of refactoring and uAPI cleanups due to a
change in the upstream direction going forward
This has all been audited with known userspace, but there may be
some pitfalls that were missed.
- i915 now uses common TTM to enable discrete memory on DG1/2 GPUs
- i915 enables Jasper and Elkhart Lake by default and has preliminary
XeHP/DG2 support
- amdgpu adds support for Cyan Skillfish
- lots of implicit fencing rules documented and fixed up in drivers
- msm now uses the core scheduler
- the irq midlayer has been removed for non-legacy drivers
- the sysfb code now works on more than x86.
Otherwise the usual smattering of stuff everywhere, panels, bridges,
refactorings.
Detailed summary:
core:
- extract i915 eDP backlight into core
- DP aux bus support
- drm_device.irq_enabled removed
- port drivers to native irq interfaces
- export gem shadow plane handling for vgem
- print proper driver name in framebuffer registration
- driver fixes for implicit fencing rules
- ARM fixed rate compression modifier added
- updated fb damage handling
- rmfb ioctl logging/docs
- drop drm_gem_object_put_locked
- define DRM_FORMAT_MAX_PLANES
- add gem fb vmap/vunmap helpers
- add lockdep_assert(once) helpers
- mark drm irq midlayer as legacy
- use offset adjusted bo mapping conversion
vgaarb:
- cleanups
fbdev:
- extend efifb handling to all arches
- div by 0 fixes for multiple drivers
udmabuf:
- add hugepage mapping support
dma-buf:
- non-dynamic exporter fixups
- document implicit fencing rules
amdgpu:
- Initial Cyan Skillfish support
- switch virtual DCE over to vkms based atomic
- VCN/JPEG power down fixes
- NAVI PCIE link handling fixes
- AMD HDMI freesync fixes
- Yellow Carp + Beige Goby fixes
- Clockgating/S0ix/SMU/EEPROM fixes
- embed hw fence in job
- rework dma-resv handling
- ensure eviction to system ram
amdkfd:
- uapi: SVM address range query added
- sysfs leak fix
- GPUVM TLB optimizations
- vmfault/migration counters
i915:
- Enable JSL and EHL by default
- preliminary XeHP/DG2 support
- remove all CNL support (never shipped)
- move to TTM for discrete memory support
- allow mixed object mmap handling
- GEM uAPI spring cleaning
- add I915_MMAP_OBJECT_FIXED
- reinstate ADL-P mmap ioctls
- drop a bunch of unused by userspace features
- disable and remove GPU relocations
- revert some i915 misfeatures
- major refactoring of GuC for Gen11+
- execbuffer object locking separate step
- reject caching/set-domain on discrete
- Enable pipe DMC loading on XE-LPD and ADL-P
- add PSF GV point support
- Refactor and fix DDI buffer translations
- Clean up FBC CFB allocation code
- Finish INTEL_GEN() and friends macro conversions
nouveau:
- add eDP backlight support
- implicit fence fix
msm:
- a680/7c3 support
- drm/scheduler conversion
panfrost:
- rework GPU reset
virtio:
- fix fencing for planes
ast:
- add detect support
bochs:
- move to tiny GPU driver
vc4:
- use hotplug irqs
- HDMI codec support
vmwgfx:
- use internal vmware device headers
ingenic:
- demidlayering irq
rcar-du:
- shutdown fixes
- convert to bridge connector helpers
zynqmp-dsub:
- misc fixes
mgag200:
- convert PLL handling to atomic
mediatek:
- MT8133 AAL support
- gem mmap object support
- MT8167 support
etnaviv:
- NXP Layerscape LS1028A SoC support
- GEM mmap cleanups
tegra:
- new user API
exynos:
- missing unlock fix
- build warning fix
- use refcount_t"
* tag 'drm-next-2021-08-31-1' of git://anongit.freedesktop.org/drm/drm: (1318 commits)
drm/amd/display: Move AllowDRAMSelfRefreshOrDRAMClockChangeInVblank to bounding box
drm/amd/display: Remove duplicate dml init
drm/amd/display: Update bounding box states (v2)
drm/amd/display: Update number of DCN3 clock states
drm/amdgpu: disable GFX CGCG in aldebaran
drm/amdgpu: Clear RAS interrupt status on aldebaran
drm/amdgpu: Add support for RAS XGMI err query
drm/amdkfd: Account for SH/SE count when setting up cu masks.
drm/amdgpu: rename amdgpu_bo_get_preferred_pin_domain
drm/amdgpu: drop redundant cancel_delayed_work_sync call
drm/amdgpu: add missing cleanups for more ASICs on UVD/VCE suspend
drm/amdgpu: add missing cleanups for Polaris12 UVD/VCE on suspend
drm/amdkfd: map SVM range with correct access permission
drm/amdkfd: check access permisson to restore retry fault
drm/amdgpu: Update RAS XGMI Error Query
drm/amdgpu: Add driver infrastructure for MCA RAS
drm/amd/display: Add Logging for HDMI color depth information
drm/amd/amdgpu: consolidate PSP TA init shared buf functions
drm/amd/amdgpu: add name field back to ras_common_if
drm/amdgpu: Fix build with missing pm_suspend_target_state module export
...
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt patches for 5.15-rc1.
Nothing huge in here, just lots of constant forward progress on a
number of different drivers and hardware support:
- more USB 4/Thunderbolt support added
- dwc3 driver updates and additions
- usb gadget fixes and addtions for new types
- udc gadget driver updates
- host controller updates
- removal of obsolete drivers
- other minor driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (148 commits)
usb: isp1760: otg control register access
usb: isp1760: use the right irq status bit
usb: isp1760: write to status and address register
usb: isp1760: fix qtd fill length
usb: isp1760: fix memory pool initialization
usb: typec: tcpm: Fix spelling mistake "atleast" -> "at least"
usb: dwc2: Fix spelling mistake "was't" -> "wasn't"
usb: renesas_usbhs: Fix spelling mistake "faile" -> "failed"
usb: host: xhci-rcar: Don't reload firmware after the completion
usb: xhci-mtk: allow bandwidth table rollover
usb: mtu3: fix random remote wakeup
usb: mtu3: return successful suspend status
usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint
usb: xhci-mtk: modify the SOF/ITP interval for mt8195
usb: xhci-mtk: add a member of num_esit
usb: xhci-mtk: check boundary before check tt
usb: xhci-mtk: update fs bus bandwidth by bw_budget_table
usb: xhci-mtk: fix issue of out-of-bounds array access
usb: xhci-mtk: support option to disable usb2 ports
usb: xhci-mtk: fix use-after-free of mtk->hcd
...
Pull networking updates from Jakub Kicinski:
"Core:
- Enable memcg accounting for various networking objects.
BPF:
- Introduce bpf timers.
- Add perf link and opaque bpf_cookie which the program can read out
again, to be used in libbpf-based USDT library.
- Add bpf_task_pt_regs() helper to access user space pt_regs in
kprobes, to help user space stack unwinding.
- Add support for UNIX sockets for BPF sockmap.
- Extend BPF iterator support for UNIX domain sockets.
- Allow BPF TCP congestion control progs and bpf iterators to call
bpf_setsockopt(), e.g. to switch to another congestion control
algorithm.
Protocols:
- Support IOAM Pre-allocated Trace with IPv6.
- Support Management Component Transport Protocol.
- bridge: multicast: add vlan support.
- netfilter: add hooks for the SRv6 lightweight tunnel driver.
- tcp:
- enable mid-stream window clamping (by user space or BPF)
- allow data-less, empty-cookie SYN with TFO_SERVER_COOKIE_NOT_REQD
- more accurate DSACK processing for RACK-TLP
- mptcp:
- add full mesh path manager option
- add partial support for MP_FAIL
- improve use of backup subflows
- optimize option processing
- af_unix: add OOB notification support.
- ipv6: add IFLA_INET6_RA_MTU to expose MTU value advertised by the
router.
- mac80211: Target Wake Time support in AP mode.
- can: j1939: extend UAPI to notify about RX status.
Driver APIs:
- Add page frag support in page pool API.
- Many improvements to the DSA (distributed switch) APIs.
- ethtool: extend IRQ coalesce uAPI with timer reset modes.
- devlink: control which auxiliary devices are created.
- Support CAN PHYs via the generic PHY subsystem.
- Proper cross-chip support for tag_8021q.
- Allow TX forwarding for the software bridge data path to be
offloaded to capable devices.
Drivers:
- veth: more flexible channels number configuration.
- openvswitch: introduce per-cpu upcall dispatch.
- Add internet mix (IMIX) mode to pktgen.
- Transparently handle XDP operations in the bonding driver.
- Add LiteETH network driver.
- Renesas (ravb):
- support Gigabit Ethernet IP
- NXP Ethernet switch (sja1105):
- fast aging support
- support for "H" switch topologies
- traffic termination for ports under VLAN-aware bridge
- Intel 1G Ethernet
- support getcrosststamp() with PCIe PTM (Precision Time
Measurement) for better time sync
- support Credit-Based Shaper (CBS) offload, enabling HW traffic
prioritization and bandwidth reservation
- Broadcom Ethernet (bnxt)
- support pulse-per-second output
- support larger Rx rings
- Mellanox Ethernet (mlx5)
- support ethtool RSS contexts and MQPRIO channel mode
- support LAG offload with bridging
- support devlink rate limit API
- support packet sampling on tunnels
- Huawei Ethernet (hns3):
- basic devlink support
- add extended IRQ coalescing support
- report extended link state
- Netronome Ethernet (nfp):
- add conntrack offload support
- Broadcom WiFi (brcmfmac):
- add WPA3 Personal with FT to supported cipher suites
- support 43752 SDIO device
- Intel WiFi (iwlwifi):
- support scanning hidden 6GHz networks
- support for a new hardware family (Bz)
- Xen pv driver:
- harden netfront against malicious backends
- Qualcomm mobile
- ipa: refactor power management and enable automatic suspend
- mhi: move MBIM to WWAN subsystem interfaces
Refactor:
- Ambient BPF run context and cgroup storage cleanup.
- Compat rework for ndo_ioctl.
Old code removal:
- prism54 remove the obsoleted driver, deprecated by the p54 driver.
- wan: remove sbni/granch driver"
* tag 'net-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1715 commits)
net: Add depends on OF_NET for LiteX's LiteETH
ipv6: seg6: remove duplicated include
net: hns3: remove unnecessary spaces
net: hns3: add some required spaces
net: hns3: clean up a type mismatch warning
net: hns3: refine function hns3_set_default_feature()
ipv6: remove duplicated 'net/lwtunnel.h' include
net: w5100: check return value after calling platform_get_resource()
net/mlxbf_gige: Make use of devm_platform_ioremap_resourcexxx()
net: mdio: mscc-miim: Make use of the helper function devm_platform_ioremap_resource()
net: mdio-ipq4019: Make use of devm_platform_ioremap_resource()
fou: remove sparse errors
ipv4: fix endianness issue in inet_rtm_getroute_build_skb()
octeontx2-af: Set proper errorcode for IPv4 checksum errors
octeontx2-af: Fix static code analyzer reported issues
octeontx2-af: Fix mailbox errors in nix_rss_flowkey_cfg
octeontx2-af: Fix loop in free and unmap counter
af_unix: fix potential NULL deref in unix_dgram_connect()
dpaa2-eth: Replace strlcpy with strscpy
octeontx2-af: Use NDC TX for transmit packet data
...
This adds the interrupt for the Sparx5 Frame DMA.
If this configuration is present the Sparx5 SwitchDev driver will use the
Frame DMA feature, and if not it will use register based injection and
extraction for sending and receiving frames to the CPU.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvebu dt64 for 5.15 (part 1)
- DTS updates for Marvell Armada CN913x platforms
+ Add support for Armada CN913x Development Board topology "B"
+ Add support for Armada CN913x Reference Design boards (CRB)
+ Fixes the NAND partitioning scheme in DTS eliminating gap between
consecutive partitions
+ Fix 10Gb ports PHY mode names
- Extend PCIe MEM space on Armada 37xx: useful for some combination
of PCIe cards where the initial 16MB was not enough
* tag 'mvebu-dt64-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
arch/arm64: dts: change 10gbase-kr to 10gbase-r in Armada
arm64: dts: add support for Marvell cn9130-crb platform
dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards
arm64: dts: cn913x: add device trees for topology B boards
Link: https://lore.kernel.org/r/878s10ypxe.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM64: DT: HiSilicon ARM64 DT updates for 5.15
- Address a PCI bus range warning of the hi3660 SoC
* tag 'hisi-arm64-dt-for-5.15' of git://github.com/hisilicon/linux-hisi:
arm64: dts: HiSilicon: hi3660: address a PCI warning
Link: https://lore.kernel.org/r/611B9BE9.8050904@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 updates for v5.15
SDM660 and SDM630 was concluded to be similar enough that they should be
merged, and the derivative SDM636 was added to the bunch. The combined
platform gained support for GPU, DMA, I2C, IMEM, display, power-domains,
SDHCI, thermal, USB, interconnects, VADC, WLED and audio remoteproc. The
Sony Xperia "Ganges" platform was similarly merged with "Nile", got
cleaned up and gained touchscreen, USB, volume keys and uSD support.
IPQ6018 gains USB2 and PCIe support and a few minor fixes. IPQ8074
gains SCM, PRNG and Crypto support and a DT style update of the PCIe
nodes.
MSM8916 gains Coresight STM support. The Xiaomi Redmi 2 is introduced,
with touchscreen, notification LED and IMU support. MSM8996 gains
support for GPU cooling and v3.0 of the SoC, which is used to introduce
support for the Sony Xperia X Performance, XZ and XZs phones.
SC7180 finally gains DisplayPort support and LPASS is updated
accordingly. A number of fixes are introduced and with the newly
introduced DRM aux bus in place Trogdor's panel is moved under the eDP
bridge. SC7280 gained USB, eMMC, SD-card, QFPROM and IPA support, the
new IDP2 board was added.
SM6126 (aka Snapdragon 665) was introduced, together with the Sony
Xperia 10II phone with support for framebuffer, USB, eMMC and volume
keys.
SM8150 gained inline crypto support for UFS enabled, CPU opp-tables was
introduced to scale DDR and L3 frequencies and SPI nodes where added, in
addition to a number of smaller fixes.
SM8250 gained a number of minor fixes and had its serial engines wired
up to use the GENI wrappers' DMA engines.
SM8350 had wakeup-parent defined for the TLMM gpio node and I2C13 was
introduced.
SDM845 display clocks was corrected and Lenovo Yoga C630 got IPA enabled
and now has working LTE connectivity.
Additionally a number of minor fixes throughout to correct DT validation
warnings.
Lastly v5.14-rc3 is merge in to resolve the merge conflicts caused by
the USB maintainer deciding to fix a regression in his tree.
* tag 'qcom-arm64-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (114 commits)
arm64: dts: qcom: sm8250: assign DSI clock source parents
arm64: dts: qcom: sdm845-mtp: assign DSI clock source parents
arm64: dts: qcom: sdm845: assign DSI clock source parents
arm64: dts: qcom: sc7180: assign DSI clock source parents
arm64: dts: qcom: sc7280-idp: Add device tree files for IDP2
dt-bindings: arm: qcom: Document qcom,sc7280-idp2 board
arm64: dts: qcom: sm8350: fix IPA interconnects
arm64: dts: qcom: sc7180: define ipa_fw_mem node
arm64: dts: qcom: sc7280: enable IPA for sc7280-idp
arm64: dts: qcom: sc7280: add IPA information
arm64: dts: qcom: sc7180-trogdor: Move panel under the bridge chip
arm64: dts: qcom: ipq8074: add PRNG node
arm64: dts: qcom: ipq8074: add crypto nodes
arm64: dts: qcom: sm8350: add qupv3_id_1/i2c13 nodes
arm64: dts: qcom: ipq6018: Add pcie support
arm64: dts: qcom: pm8150b: Add DTS node for PMIC VBUS booster
arm64: dts: qcom: sm8150: add SPI nodes
arm64: dts: qcom: msm8916: Enable CoreSight STM component
arm64: dts: qcom: sc7280: Add qfprom node
arm64: dts: qcom: sc7280: Fixup the cpufreq node
...
Link: https://lore.kernel.org/r/20210816231223.586597-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Current PCIe MEM space of size 16 MB is not enough for some combination
of PCIe cards (e.g. NVMe disk together with ath11k wifi card). ARM Trusted
Firmware for Armada 3700 platform already assigns 128 MB for PCIe window,
so extend PCIe MEM space to the end of 128 MB PCIe window which allows to
allocate more PCIe BARs for more PCIe cards.
Without this change some combination of PCIe cards cannot be used and
kernel show error messages in dmesg during initialization:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:00:00.0: BAR 6: assigned [mem 0xe8000000-0xe80007ff pref]
pci 0000:01:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:01:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:02:03.0: BAR 8: no space for [mem size 0x01000000]
pci 0000:02:03.0: BAR 8: failed to assign [mem size 0x01000000]
pci 0000:02:07.0: BAR 8: no space for [mem size 0x00100000]
pci 0000:02:07.0: BAR 8: failed to assign [mem size 0x00100000]
pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit]
pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit]
Due to bugs in U-Boot port for Turris Mox, the second range in Turris Mox
kernel DTS file for PCIe must start at 16 MB offset. Otherwise U-Boot
crashes during loading of kernel DTB file. This bug is present only in
U-Boot code for Turris Mox and therefore other Armada 3700 devices are not
affected by this bug. Bug is fixed in U-Boot version 2021.07.
To not break booting new kernels on existing versions of U-Boot on Turris
Mox, use first 16 MB range for IO and second range with rest of PCIe window
for MEM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 76f6386b25 ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The USB maintainer felt the strong need to push '1f958f3dff42
("Revert "arm64: dts: qcom: Harmonize DWC USB3 DT nodes name"")'
through the usb tree, so merge v5.14-rc3 to resolve the resulting merge
conflicts.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Qualcomm ARM64 fixes for v5.14
This fixes three regressions across Angler and Bullhead, introduced by
advancements in the platform definition. It then corrects the powerdown
GPIOs for the speaker amps on C630 and lastly fixes a typo that assigned
CPU7 in SC7280 to the wrong CPUfreq domain.
* tag 'qcom-arm64-fixes-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sdm845-oneplus: fix reserved-mem
arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem
arm64: dts: qcom: sc7280: Fixup cpufreq domain info for cpu7
arm64: dts: qcom: msm8992-bullhead: Fix cont_splash_mem mapping
arm64: dts: qcom: msm8992-bullhead: Remove PSCI
arm64: dts: qcom: c630: fix correct powerdown pin for WSA881x
Link: https://lore.kernel.org/r/20210816205030.576348-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v5.15-rc1
Contains a couple of fixes across the board and adds support for the
recently released NVIDIA Jetson TX2 NX Developer Kit.
* tag 'tegra-for-5.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix compatible string for Tegra132 CPUs
arm64: tegra: Add missing interconnects property for USB on Tegra186
arm64: tegra: Add NVIDIA Jetson TX2 NX Developer Kit support
arm64: tegra: Add PWM nodes on Tegra186
arm64: tegra194: p2888: Correct interrupt trigger type of temperature sensor
arm64: tegra: Fix Tegra194 PCIe EP compatible string
Link: https://lore.kernel.org/r/20210813162157.2820913-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
qup-i2c devices on sc7180 are clocked with a fixed clock (19.2 MHz)
Though qup-i2c does not support DVFS, it still needs to vote for a
performance state on 'CX' to satisfy the 19.2 Mhz clock frequency
requirement.
Use 'required-opps' to pass this information from
device tree, and also add the power-domains property to specify
the CX power-domain.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Traverse Technologies Ten64 is a Mini-ITX form factor
networking board using the NXP LS1088A SoC.
This device tree only describes features which the mainline
kernel currently has support for, such as some I2C-connected
devices that are not described at present.
System documentation may be found at ten64doc.traverse.com.au
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> # for the MAC/PHY
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Performance Manager Unit was not described in the DTS
which meant performance event monitoring was not possible.
This was exposed by a change to the PMU handling in KVM
in 5.11-rc3 which now prevents a PMU being exposed to a
guest when the host does not provide one:
"KVM: arm64: Don't access PMCR_EL0 when no PMU is available"
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A previous patch added the PCS for DPMAC2 only, as
used for the AQR PHY on the LS1088ARDB.
DPMAC1 PCS access is required for PHYLINK SFP support
on the Traverse Ten64 board.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds sound support to the Reform2.
It differs from the downstream implementation in that the codec
is used as the BCLK and FSYNC master and the i.MX8MQ only supplies
a fixed 25MHz MCLK from the oscillator. This allows to support
a wider range of audio rates by using the codec PLL and to shut
down the audio PLLs on the i.MX8MQ SoC side.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8QXP features four Cortex-A35 cores, use more accurate
compatible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM features four Cortex-A53 cores, update the compatible
to use more accurate "arm,cortex-a53-pmu"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The USB hub has it's reset as GPIO4_IO17 but can be sub-loaded and
VBUS provided by a VBUS regulator with GPIO4_IO2 as the enable and
GPIO1_IO15 as the active-low over-current.
Enable pull-up for GPIO4_IO17 to keep hub out of reset and move VBUS
enable to GPIO4_IO2. Additionally enable pull-up on GPIO1_IO15 so that
if the hub is loaded it never over-currents.
This allows USB to work in both configurations without a device-tree
change.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW700x PMIC does not have an interrupt. Remove the invalid pin
config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the 2 available CSI interfaces on the i.MX8MQ with the MIPI-CSI2
receiver (new driver) and the CSI Bridge that provides the user buffers
(existing driver).
An image sensor is to be connected to the MIPIs' second port, to be described
in board files.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8 MPlus SoC integrates Cadence HIFI4 DSP. This core runs either a
custom firmware or the open source SOF firmware [1]
DSP device is handled by SOF OF driver found in
sound/soc/sof/sof-of-dev.c
Notice that the DSP node makes use of:
- dsp_reserved, a reserved memory region for various Audio
resources (e.g firmware loading, audio buffers, etc).
- Messaging Unit (mu2) for passing notifications betweem ARM
core and DSP.
[1] https://thesofproject.github.io/latest/platforms/index.html
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Unnecessary blank lines do NOT help readability, so remove them.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following dtc build warning is seen with W=1:
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts:291.14-397.4: Warning (avoid_unnecessary_addr_size): /soc@0/bus@30800000/i2c@30a20000/gsc@20: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unnecessary #address-cells/#size-cells to fix it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following warnings reported by checkpatch:
arch/..../imx8qxp-ai_ml.dts:198: WARNING: please, no space before tabs
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the IRQs for both the QSGMII PHYs and the 10GBASE-R PHY found
on the LS1088ARDB board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the DTS nodes corresponding to the 4 10GBASE-R PHYs to describe
their IRQ lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the DTS nodes for both the AR8035 and the AQR107 PHYs in order to
describe their IRQ lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the driver is registered, it produces a warning when
registering the PCI bridge:
[ 5.363450] pci_bus 0000:00: root bus resource [bus 00-01]
[ 5.396998] pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-01] (conflicts with (null) [bus 00-01])
[ 5.284831] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
The reason is that the bus-range is wrong. Address it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
