* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cio: online_store - trigger recognition for boxed devices
[S390] cio: disallow online setting of device in transient state
[S390] cio: introduce notifier for boxed state
[S390] cio: introduce ccw_device_schedule_sch_unregister
[S390] cio: wake up on failed recognition
[S390] fix hypfs build failure
[PATCH] sysrq: include interrupt.h instead of irq.h
The current logic for dmi matching in efifb does not allow efifb to load
on all hardware that we can dmi match for.
For a real world example, boot with elilo (3.7 or 3.8 vanilla) and on a
Apple (MacBook) and EFI framebuffer driver will not load (you will have no
video). This specific hardware is efi v1.10, so we have UGA and not GOP.
Without special bootloader magic (i.e. extra elilo patches for UGA
graphics detection) no screen info will be passed to the kernel and as a
result efifb will not load.
This patch allows the dmi match to happen by moving it to earlier in
efifb_init, and sets the video type (in set_system) so that efifb can load
when we have a valid dmi match and already know the specifics of the
hardware.
Without this patch the efifb driver will fail to load in the event screen
info is not found and passed in by the bootloader, being that we will
never get to look for a dmi match. A primary reason for matching with dmi
is because not all bootloaders detect the video info properly. The
solution is that in the event of a dmi match, we should set
screen_info.orig_video_isVGA. Most bootloaders fail to set screen info on
Apple hardware, and this is a big problem for people who use Apple
hardware.
Tested on a MacBook SantaRosa with elilo-3.8 (vanilla) and resolves the
issue, the dmi match now works, EFI framebuffer now loads and video works.
Signed-off-by: Brian Maly <bmaly@redhat.com>
Acked-by: Huang Ying <ying.huang@intel.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Chandramouli Narayanan <mouli@linux.intel.com>
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove Kconfig option for tridentfb acceleration. The acceleration can be
switched off with modules "noaccel" parameter.
The acceleration for Trident chips was fixed in the 2.6.27 kernel.
Also, add CyberXXX and CyberBlade names to Kconfig option's name. It should
make easier to find the tridentfb choice for cyblafb driver's users. The
cyblafb driver has been replaced by the tridentfb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Save one fifo entry on cursor enabling and disabling.
Save another fifo entry for FB_CUR_SETPOS operation by removing redundant one.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A hardware cursor is left enabled in the fb_set_par() which is called when a
new console is created. This is inconsistent with software cursor's
behaviour.
Also, this makes a hardware cursor always visible in the Xfbdev (Xorg kdrive)
server.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Risto Suominen <risto.suominen@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove mutex from the nvidiafb_open/nvidiafb_release functions as these
operations are mutexed at fb layer.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add suspend/resume for the Acer Travelmate 290D/292LMi with the following
graphic-chip:
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV350
[Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA controller])
Subsystem: Acer Incorporated [ALI] TravelMate 290 [1025:005a]
Flags: bus master, 66MHz, medium devsel, latency 128, IRQ 10
Memory at a8000000 (32-bit, prefetchable) [size=128M]
I/O ports at c100 [size=256]
Memory at e0010000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at a0000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Capabilities: [50] Power Management version 2
Kernel driver in use: radeonfb
Kernel modules: radeonfb
Signed-off-by: Wolfgang Kroener <lkml@azog.de>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The blank operation should receive FB_BLANK_POWERDOWN, not VESA_POWERDOWN.
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrea Righi <righi.andrea@gmail.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Cc: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the vbemode option is used, uvesafb calls fb_get_mode() without first
setting the resolution in info->var. This results in a division by zero
in fb_get_mode(), as evidenced e.g. in [1]. Fix this by ensuring the
info->var structure is populated before fb_get_mode() is called.
[1] http://bugzilla.kernel.org/show_bug.cgi?id=11661#c37
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A tridentfb driver has all the functionality of the cyblafb driver without
the bugs of the latter.
Changes to the tridentfb driver:
- FBINFO_READS_FAST added to the tridentfb. The cyblafb used a blitter
for scrolling which is faster than color expansion on Cyberblade
chipsets. The blitter is slower on a discrete Blade3D core. Use the
blitter for scrolling in the tridentfb only for integrated Blade3D
cores. Now, scrolling speed is about equal for the tridentfb and the
cyblafb.
- a copyright notice addition is done on request of Jani Monoses (the
first author of the tridentfb).
Tested on AGP Blade3D card and PCChips
M787CLR motherboard: VIA C3 cpu +
VT8601 north bridge (aka Cyberblade/i1).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Jani Monoses" <jani@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the newer Samsung devices, such as found in the S3C2443,
S3C6400 or S3C6410 series SoC.
It currently does not support all the alpha- or chroma-key options but it
will support more exporting more than one framebuffer ready for adding
overlay and blending functions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no entry for n411.c to be built, include one in Makefile.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Otherwise this will already return 0 if iteration MAXLOOP-2 occurs in the
first loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michal Januszewski <michalj@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Michal Januszewski <michalj@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Ondrej Zajicek <santiago@crfreenet.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix cmap leak in removal path
- fix cmap leak when register_framebuffer fails
- check return value of fb_alloc_cmap
- don't continue with driver setup if register_framebuffer fails
[krzysztof.h1@wp.pl: spotted missing iounmap]
[randy.dunlap@oracle.com: move data declaration before any code]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With for(div = 0; div < max_clk_div; div++) { ... } div reaches max_clk_div.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Joe Perches <joe@perches.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The s1d13xxx chip provides two values of identification value: the
Production id (e.g 13506/13505/13806..) and a revision number 0,1,2,3).
Together these can help us to differentiate between similiar setups.
This patch adds the proper way of grabbing both those values and save them
for future reference (in order to decide what functions a card supports,
e.g acceleration).
We also move away from the concept of all s1d13xxx = s1d13806 when we
really support alot more.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify s1d13xxxfb_probe()]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix cmap leak in removal path
- fix cmap leak when register_framebuffer fails
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix cmap leak in removal path
- fix cmap leak when register_framebuffer fails
- check return value of fb_alloc_cmap
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix cmap leak when register_framebuffer fails.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- fix cmap leak in removal path
- fix cmap leak when register_framebuffer fails
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bad example code, no cookie!
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were leaking the cmap memory.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were leaking the cmap memory.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were leaking the cmap memory.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We were leaking both the cmap memory and the info struct memory.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a circular locking dependency in the frame buffer console driver
pushing down the mutex fb_info->lock.
Circular locking dependecies occur calling the blocking
fb_notifier_call_chain() with fb_info->lock held. Notifier callbacks can
try to acquire mm->mmap_sem, while fb_mmap() acquires the locks in the
reverse order mm->mmap_sem => fb_info->lock.
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix calculations of timings for interlaced modes.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix threshold register mask for Laguna chips otherwise some 8bpp modes are
garbled after selecting a 24bpp mode.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix handling of the Cirrus Logic GD5434 chip. Distinguish this chip from the
GD5430. It allows detecting memory size for both models correctly.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A memory clock (MCLK) is set at various places. Move the setting into one
place.
Set the MCLK only for Zorro cards as the x86 cards should be initialized by
BIOS.
Improve handling of the GD5434 (SD64).
Kill one annoying debug output "virtual offset: ...".
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an accelerator constant so almost all Cirrus are recognized as
accelerators by the fbset command.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cirrus' Alpine and Picasso4 chips uses DAC clock doubling to achieve full
range of pixclock frequencies.
[akpm@linux-foundation.org: fix spelling, use usual comment layout]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 32bpp is supported only on the latest Cirrus Logic chips. Use the
24bpp which is supported at least since Alpine chips (GD543x).
Change 32bpp mode setting to 24bpp mode. Change acceleration as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various fixes to make Cirrus GD5446 chip work.
Another Cirrus chip works with the cirrusfb. The gd5446 seems very
similar to Alpine chips.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balance iomap and iounmap and alloc and free calls in case of error druing
device register (probing).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add hardware color expansion (imageblit) function. It roughly doubles
scrolling speed of my Alpine card (GD5430).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fix color expansion for 16bpp and 32bpp modes in the
cirrusfb_RectFill().
- Make a function with a common blitter code (cirrusfb_set_blitter).
- Add fb_sync function to allow a higher layer synchronize with the
blitter.
- Kill one redundant blitter reset.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- The Laguna GD5465 (AGP) has one register more than non-AGP chips.
Recognize the AGP version and write a tile control register only on the
AGP version. Tested only on an AGP card.
- Bump up RAMDAC frequencies after X11 code. This allow to drive a flat
panel resolution 1680x1050 at 16bpp from the 4MB card.
- Fix screen start address overflow bits on Laguna cards (CRT1D
register).
- Fix exit path in the cirrusfb_pci_register() in case of error.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Break cirrusfb_decode_var() function into two parts:
cirrusfb_check_pixclock() which can be called from the
cirrusfb_check_var() aand merge rest into the cirrusfb_set_par_foo().
This allows rejecting modes with too high pixclock before before any
change to hardware state (and a console is messed up).
Also, fix RGB field's lengths for 8bpp modes to correct ones so X11 works
with fbdev driver with cirrusfb.
Kill some redundant function calls or register loads.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix 8bpp mode by adding handling of the Laguna chipsets to various places
and stop trashing a HDR register which probably does not exist on the
Laguna.
Fix compilation warnings about uninitialized variables also.
Finally, all 8bpp, 16bpp and 32bpp modes work on the Laguna chipset.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various improvements to the code:
- kill a structure with only one
field: multiplexing and use the
field directly
- move the cirrusfb_ops structure
down the file to kill forward
declarations
- move cirrusfb_init() to kill
forward declaration
- kill register loads done already
in the init_vgachip()
- kill assigments done by higher
layer in the cirrusfb_pan_display()
- do not overwrite line pitch bit in
the CL_CRT1D register
- kill btype variables if they were
used only once or twice
- add cpu_relax() in the busy waiting
loop
The fix to the CL_CRT1D register handling makess the 1024x768 32bpp mode
work. Previously, only lower resolution modes have worked with 32bpp.
Signed-off-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the 5-6-5 RGB mode instead of the 5-5-5 mode at 16bpp depth.
It fixes colors in the 16bpp modes on Cirrus Laguna chips.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Cc: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A line length is calculated twice: first in the cirrusfb_decode_var() then
in the cirrusfb_set_par_foo().
Use the first calculated value. A nice side effect is that 32bpp mode
works now.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert.uytterhoeven@gmail.com>
Cc: Arthur Marsh <arthur.marsh@internode.on.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Laguna chipsets use special registers which are available through the
mmio area. The cirrusfb driver does not use memory mapped registers for
the PCI cards.
Add the memory mapped area for Laguna chipsets and add basic usage of the
special Laguna registers after SVGALIB code.
This gives readable console at 16bpp on the GD-5465 (Laguna AGP). The
8bpp and 32bpp depths are still broken.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add additional overflow register setting for Laguna chips.
Also, simplify some code in the cirrusfb_pan_display() and
cirrusfb_blank().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix memory detection and clock setting for Cirrus Laguna chipsets
(GD5464/GD5465). The changes are done after the Xorg code.
The driver still does not display anything on the GD5465 but it switches
resolutions correctly at least.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert all printks to dev_dbg, dev_info or dev_err. Kill some excessive
debug information and code in the process.
[akpm@linux-foundation.org: printk fixes]
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GFP_KERNEL is legal here - we don't need to use gfp_any().
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
new_alarm is unsigned so test before the subtraction.
[akpm@linux-foundation.org: time-wrapping fix]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a postfix decrement retries will reach -1 rather than 0, so the
warning and error-out will not occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the EPSON RX8025 RTC. The date/time registers of this
chip are compatible with the DS1307.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the rtc-ds1307 driver to work with SMBus controllers like nforce2
that do not support i2c block transfers.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: BARRE Sebastien <sbarre@sdelcc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This isn't a hotpluggable device, so call platform_driver_probe
directly in parisc_rtc_init
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the return value of rtc_valid_tm() instead of just returning 0.
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
parisc_rtc now only includes an rtc_device pointer, so let's
just use the rtc_device type directly.
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RTC subsystem proides ops locking, no need to implement our own
Signed-off-by: dann frazier <dannf@hp.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- the LEAP_YEAR macro is buggy - it references its arg multiple times.
Fix this by turning it into a C function.
- give it a more approriate name
- Move it to rtc.h so that other .c files can use it, instead of copying it.
Cc: dann frazier <dannf@hp.com>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: stephane eranian <eranian@googlemail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are the only two ioctls so the ioctl() function is also removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bindings describes a case where MMC/SD/SDIO slot directly connected to
a SPI bus. Such setups are widely used on embedded PowerPC boards.
The patch also adds the mmc-spi-slot entry to the OpenFirmware modalias
table.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement full support for OF SPI bindings. Now the driver can manage its
own chip selects without any help from the board files and/or fsl_soc
constructors.
The "legacy" code is well isolated and could be removed as time goes by.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main purpose of this patch is to pass 'struct spi_device' to the chip
select handling routines. This is needed so that we could implement
full-fledged OpenFirmware support for this driver.
While at it, also:
- Replace two {de,activate}_cs routines by single cs_contol().
- Don't duplicate platform data callbacks in mpc83xx_spi struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch fixes following sparse warnings:
CHECK spi_mpc83xx.c
spi_mpc83xx.c:145:1: warning: symbol 'mpc83xx_spi_rx_buf_u8' was not declared. Should it be static?
spi_mpc83xx.c:146:1: warning: symbol 'mpc83xx_spi_rx_buf_u16' was not declared. Should it be static?
spi_mpc83xx.c:147:1: warning: symbol 'mpc83xx_spi_rx_buf_u32' was not declared. Should it be static?
spi_mpc83xx.c:148:1: warning: symbol 'mpc83xx_spi_tx_buf_u8' was not declared. Should it be static?
spi_mpc83xx.c:149:1: warning: symbol 'mpc83xx_spi_tx_buf_u16' was not declared. Should it be static?
spi_mpc83xx.c:150:1: warning: symbol 'mpc83xx_spi_tx_buf_u32' was not declared. Should it be static?
spi_mpc83xx.c:175:32: warning: incorrect type in initializer (different address spaces)
spi_mpc83xx.c:175:32: expected void *tmp_ptr
spi_mpc83xx.c:175:32: got unsigned int [noderef] <asn:2>*<noident>
spi_mpc83xx.c:183:26: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:183:26: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:183:26: got void *tmp_ptr
spi_mpc83xx.c:184:26: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:184:26: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:184:26: got void *tmp_ptr
spi_mpc83xx.c:287:31: warning: incorrect type in initializer (different address spaces)
spi_mpc83xx.c:287:31: expected void *tmp_ptr
spi_mpc83xx.c:287:31: got unsigned int [noderef] <asn:2>*<noident>
spi_mpc83xx.c:295:25: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:295:25: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:295:25: got void *tmp_ptr
spi_mpc83xx.c:296:25: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:296:25: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:296:25: got void *tmp_ptr
spi_mpc83xx.c:486:13: warning: symbol 'mpc83xx_spi_irq' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make use of the new abstraction layer and add a new transport layer for
spi. Works fine on a PXA based board.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This solves the dependency between lis3lv02d.[ch] and ACPI specific
methods. It introduces a ->bus_priv pointer to the device struct which is
casted to 'struct acpi_device' in the ACIP layer. Changed hp_accel.c
accordingly.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move lis3lv02d_init_device() down so that the forward declaration of
lis3lv02d_add_fs() becomes unnecessary.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a laptop HP Compaq 8710W, I compiled into my kernel the LIS3LV02DL
and HP_ACCEL module drivers. While loading it cannot recognize the laptop
model, so i am sending the necessary information to update the database of
axis orientations.
>When the laptop is horizontal the position reported is about 0 for X and Y
>and a positive value for Z
Yes, it is about 0,0,1000, the actual reading says: (-17,-26,1018);
> If the left side is elevated, X increases (becomes positive)
Yes, X goes toward to positive 1000.
>If the front side (where the touchpad is) is elevated, Y decreases (becomes negative)
No, Y goes toward to positive 1000.
>If the laptop is put upside-down, Z becomes negative
Yes, the laptop on a table Z gives 1000, and if upsidedown the Z reads
-1000.
So in few words the Y axis is inverted.
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two more laptops to whitelist.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.
I have tested the driver with my board, and it appears to work fine. With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power. With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power. I'm not drawing any current at the
moment, so this is reasonable. The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.
I didn't attempt to support changing any of the chip's settings or
enabling the FET. I'm not sure even how to do that and still fit within
the hwmon framework. :)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip
Signed-off-by: Davide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Andrew noted, adev is pretty poor name for symbol being exported.
Rename it to lis3.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Cc: <Quoc.Pham@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce keyed event wakeups inside the TTY code.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: William Lee Irwin III <wli@movementarian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a driver for Intersil's ISL29003 ambient light sensor device plus some
documentation. Inspired by tsl2550.c, a driver for a similar device.
It is put in drivers/misc for now until the industrial I/O framework gets
merged.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change hpilo open and close logic to spin for 10usec between checking device,
rather than every usec.
Because the loop is coded to take up to 10ms, it seemed prudent to
increase the interval between polling the device, to reduce the load on
the system and allow more other work to happen.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove PARPORT dependency for Auxiliary Display support.
This is not needed since the dependency for the KS0108 driver is
PARPORT_PC.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the filesystem freeze operation has been elevated to the VFS, and
is just an ioctl away, some sort of safety net for unintentionally frozen
root filesystems may be in order.
The timeout thaw originally proposed did not get merged, but perhaps
something like this would be useful in emergencies.
For example, freeze /path/to/mountpoint may freeze your root filesystem if
you forgot that you had that unmounted.
I chose 'j' as the last remaining character other than 'h' which is sort
of reserved for help (because help is generated on any unknown character).
I've tested this on a non-root fs with multiple (nested) freezers, as well
as on a system rendered unresponsive due to a frozen root fs.
[randy.dunlap@oracle.com: emergency thaw only if CONFIG_BLOCK enabled]
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: Takashi Sato <t-sato@yk.jp.nec.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the page_mkwrite prototype to take a struct vm_fault, and return
VM_FAULT_xxx flags. There should be no functional change.
This makes it possible to return much more detailed error information to
the VM (and also can provide more information eg. virtual_address to the
driver, which might be important in some special cases).
This is required for a subsequent fix. And will also make it easier to
merge page_mkwrite() with fault() in future.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <joel.becker@oracle.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Felix Blyakher <felixb@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct tty_operations::proc_fops took it's place and there is one less
create_proc_read_entry() user now!
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we use a shared legacy IRQ then our interrupt handler may be called
as soon as it is registered even though IRQs are disabled on the NIC.
Now that the legacy interrupt handler also checks for event delivery,
it may decide to schedule polling in this case. Ensure that the NAPI
context is valid but disabled at this point.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let driver depend on HAS_IOMEM to avoid build breakage on s390:
CC drivers/net/ethoc.o
drivers/net/ethoc.c: In function 'ethoc_read':
drivers/net/ethoc.c:221: error: implicit declaration of function 'ioread32'
drivers/net/ethoc.c: In function 'ethoc_write':
drivers/net/ethoc.c:226: error: implicit declaration of function 'iowrite32'
drivers/net/ethoc.c: In function 'ethoc_rx':
drivers/net/ethoc.c:405: error: implicit declaration of function 'memcpy_fromio'
drivers/net/ethoc.c: In function 'ethoc_start_xmit':
drivers/net/ethoc.c:828: error: implicit declaration of function 'memcpy_toio'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
... and access them afterwards. Simplify rq completing code while at it.
Spotted-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
No reason to need IDE built-in to be able to compile pmac driver.
Tested to work on 2.6.29-rc8 and 2.6.28.8 with ide and pmac as modules
inside an initramfs.
Signed-off-by: Gilles Espinasse <g.esp@free.fr>
Cc: sam@ravnborg.org
Cc: benh@kernel.crashing.org
[bart: remove now superfluous IDE check]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
As IDE cable used on Apple PowerBook/iBook laptops are always of "Short 40"
type when the firmware says it's 80 conductor one, the cable detection should
return ATA_CBL_PATA40_SHORT on those machines. This enables to automatically
use UDMA5 even with drives that doesn't correctly detect those cables on Apple
laptops.
Signed-off-by: TOMARI Hisanobu <posco.grubb@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: benh@kernel.crashing.org
[bart: beautify patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since SELECT_DRIVE() has boiled down to a mere dev_select() method call, it now
makes sense to just inline it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Turn selectproc() method into dev_select() method by teaching it to write to the
device register and moving it from 'struct ide_port_ops' to 'struct ide_tp_ops'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: benh@kernel.crashing.org
Cc: petkovbb@gmail.com
[bart: add ->dev_select to at91_ide.c and tx4939.c (__BIG_ENDIAN case)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move IDE_FTFLAG_{IN|OUT}_DATA flag handling out of tf_{read|load}() methods
into the only two functions where these flags actually need to be handled:
do_rw_taskfile() and ide_complete_cmd()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Handle IDE_FTFLAG_{IN|OUT}_DATA flags in tf_{read|load}() methods by calling
{in|out}put_data() methods to transfer 2 bytes -- this will allow us to move
that handling out of those methods altogether...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_{in|out|put_data() can be somewhat shortened by merging the paths doing
16-bit I/O...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The feature register has never been readable -- when its location is read, one
gets the error register value; hence rename IDE_TFLAG_IN_[HOB_]FEATURE into
IDE_TFLAG_IN_[HOB_]ERROR and introduce the 'hob_error' field into the 'struct
ide_taskfile' (despite the error register not really depending on the HOB bit).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Turn set_irq() method with its software reset hack into write_devctl() method
(for just writing a value into the device control register) at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make use of ATA_HOB instead of hard-coded value in the tf_read() method.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make use of ATA_ERR instead of hard-coded value in idedisk_set_max_address()
and idedisk_read_native_max_address().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for the CompactFlash specific PIO modes 5/6 and MWDMA modes 3/4.
Since there were no PIO5 capable hard drives produced and one would also need
66 MHz IDE clock to actually get the difference WRT the address setup timings
programmed, I decided to simply replace the old non-standard PIO mode 5 timings
with the CFA specified ones.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stf_xl@wp.pl
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bytes indicating current DMA mode in the identify data words 62, 63, and 88
should only change on setting a DMA mode, so stop clearing them on setting PIO
mode in ide_config_drive_speed(). While at it, correct SW/MW DMA mode masks...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The IDE code assumed for years that the bit 1 of the identify data word 53 also
covers the validity of the SW/MW DMA information in words 62 and 63, but it has
always covered only words 64 thru 70, with words 62 and 63 being defined in the
original ATA spec, not in ATA-2...
This fix however should only concern *very* old hard disks and rather old CF
cards...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make auide_{insw|outsw}() 'static' and mark them 'inline' as there's only one
call site for each: in the driver's {in|out}put_data() methods respectively...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix ide_init_sg_cmd() setup for non-fs requests.
* Convert ide_pc_intr() to use ide_pio_bytes() for floppy media.
* Remove no longer needed ide_io_buffers() and sg/sg_cnt fields
from struct ide_atapi_pc.
* Remove partial completions; kill idefloppy_update_buffers(), as a
result.
* Add some more debugging statements.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return number of bytes left to transfer from idetape_{in,out}put_buffers()
and number of bytes done from ide_tape_io_buffers().
* Fix padding for PIO transfers in ide_pc_intr() so read/write buffers are
always completely processed and then the transfer is padded if necessary.
* Remove invalid error messages.
* Remove now superfluous padding from ide{_io_buffers,tape_input_buffers}().
While at it:
* Set pc->bh to NULL in idetape_input_buffers() after all bh-s are done.
* Cache !!(pc->flags & PC_FLAG_WRITING) in local variable in ide_pc_intr().
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays it is not worth having a separate config option for
Amiga IDE Doubler support so always include it (it still needs
to be explicitly enabled by module parameter).
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
struct ide_atapi_pc is often allocated on the stack and size of ->pc_buf
size is 256 bytes. However since only ide_floppy_create_read_capacity_cmd()
and idetape_create_inquiry_cmd() require such size allocate buffers for
these pc-s explicitely and decrease ->pc_buf size to 64 bytes.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is no need for a separate ide_arm host driver nowadays
so merge it into ide_generic one.
While at it:
- return -EBUSY from ide_generic_init() if I/O resources are busy
- scale down ide_generic_check_pci_legacy_iobases() for CONFIG_PCI=n
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays we have "ide_generic.probe_mask=" module parameter
and ide_platform host driver so sysfs interface for adding
IDE interfaces is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide_map_sg() calls out from ide_build_sglist()
to ide_dma_prepare().
* Pass command to ide_destroy_dmatable().
* Rename ide_build_sglist() to ide_dma_map_sg()
and ide_destroy_dmatable() to ide_dma_unmap_sg().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set/clear drive->waiting_for_dma flag in the core code
instead of in ->dma_setup and ->dma_end methods.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move ide_map_sg() call from ->dma_setup implementations and
ide_destroy_dmatable() one from *_build_dmatable() to ide_dma_prepare().
There should be no functional changes caused by this patch.
Sergei:
Removed 'use_pio_instead' labels and replaced 'goto' with 'return 0' --
that required no changes to the follow-up patches...
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add (an optional) ->dma_check method for checking if DMA can be
used for a given command and fail DMA setup in ide_dma_prepare()
if necessary.
* Convert alim15x3 and trm290 host drivers to use ->dma_check.
* Rename ali15x3_dma_setup() to ali_dma_check() while at it.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use custom ->dma_{start,end} methods to handle trm290_prepare_drive()
there instead of in ->dma_setup method.
There should be no functional changes caused by this patch
(DMA support is disabled currently in trm290.c).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use custom ->dma_{start,end} methods to handle ns87415_prepare_drive()
there instead of in ->dma_setup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_dma_prepare() helper.
* Convert ide_issue_pc() and do_rw_taskfile() to use it.
* Make ide_build_sglist() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_dma_timeout() is only used by ide_dma_timeout_retry()
inline it there.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All custom ->dma_timeout implementations call the generic one thus it is
possible to have only an optional method for resetting DMA engine instead:
* Add ->dma_clear method and convert hpt366, pdc202xx_old and sl82c105
host drivers to use it.
* Always use ide_dma_timeout() in ide_dma_timeout_retry() and remove
->dma_timeout method.
* Make ide_dma_timeout() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cache drive->queue in local variable and use max().
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'thislen' is always <= cmd->nleft for non-fs requests so the transfer
padding inside the 'while (thislen > 0)' loop can happen only for fs
requests -- then move it out of the loop and unify with the transfer
padding for non-fs requests ('thislen' == 'len' for fs requests).
* blk_dump_rq_flags() dumps all request flags so it is enough to pass
only the function name to it.
* Update my Copyrights while at it.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use the following facts:
- rq->nr_sectors should now be always equal to (non-zero)
rq->hard_nr_sectors for fs requests
- REQ_TYPE_ATA_PC requests have never bio attached to them
- rq->hard_nr_sectors == 0 for REQ_TYPE_ATA_PC requests
- DMA is used only for fs, pc and REQ_TYPE_ATA_PC requests
- 'uptodate' is ignored for pc requests ('rc == 0' case)
and use the common completion path also for DMA requests.
There should be no functional changes caused by this patch
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert ide-cd to use scatterlists for PIO transfers and get rid of
partial completions (except on error) also for non-fs requests.
v2:
Do not map dataless commands to an sg since it oopses on the virt_to_page()
translation check when DEBUG_VIRTUAL is enabled. (from Borislav Petkov,
reported/bisected-by Tetsuo Handa).
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We now support arbitrary number of bytes per-IRQ also for fs requests
so remove ide_cd_check_transfer_size() and IDE_AFLAG_LIMIT_NFRAMES.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Export ide_pio_bytes().
* Add ->last_xfer_len field to struct ide_cmd.
* Add ide_cd_error_cmd() helper to ide-cd.
* Convert ide-cd to use scatterlists also for PIO transfers (fs requests
only for now) and get rid of partial completions (except when the error
happens -- which is still subject to change later because looking at
ATAPI spec it seems that the device is free to error the whole transfer
with setting the Error bit only on the last transfer chunk).
* Update ide_cd_{prepare_rw,restore_request,do_request}() accordingly.
* Inline ide_cd_restore_request() into cdrom_start_rw().
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Inline cdrom_end_request() into cdrom_newpc_intr()
and ide_cd_do_request().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move cdrom_end_request() calls from cdrom_decode_status()
and ide_cd_check_ireason() to cdrom_newpc_intr().
* Unify cdrom_newpc_intr() exit paths.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move setting REQ_FAILED flag out from 'end_request' exit path in
cdrom_newpc_intr() and also rename 'end_request' to 'out_end'.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move cdrom_end_request() calls from cdrom_start_rw()
and ide_cd_prepare_rw_request() to ide_cd_do_request().
* Unify ide_cd_do_request() exit paths.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It makes no sense to check for BSY bit being set as earlier OK_STAT()
check in cdrom_end_request() makes sure that BSY bit is cleared.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_end_rq() also for failed non-fs requests on completion
of REQUEST SENSE requests + use blk_rq_bytes() while at it.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use PageHighMem() instead of ifdefs in ide_pio_bytes()
(=> local IRQs won't be disabled when not necessary).
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add support for arbitrary transfer lengths to ide_pio_bytes()
and then inline ide_pio_multi() into ide_pio_datablock().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently¹, some ATAPI devices want to see the packet command first
before enabling DMA otherwise they simply hang indefinitely. Reorder the
two steps and start DMA only after having issued the command first.
[1] http://marc.info/?l=linux-kernel&m=123835520317235&w=2
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Reported-by: Michael Roth <mroth@nessie.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix some incorrect IDE_FTFLAG_* changes which slipped in commit
"ide: add "flagged" taskfile flags to struct ide_taskfile (v2)"
(commit 19710d25d5) few days ago.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On m68k:
| drivers/ide/ide-atapi.c: In function 'ide_io_buffers':
| drivers/ide/ide-atapi.c:87: error: implicit declaration of function 'sg_page'
| drivers/ide/ide-atapi.c:87: warning: passing argument 1 of 'PageHighMem' makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:91: warning: passing argument 1 of 'kmap_atomic' makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:96: error: implicit declaration of function 'sg_virt'
| drivers/ide/ide-atapi.c:96: warning: assignment makes pointer from integer without a cast
| drivers/ide/ide-atapi.c:107: error: implicit declaration of function 'sg_next'
| drivers/ide/ide-atapi.c:107: warning: assignment makes pointer from integer without a cast
[bart: Dmitri Vorobiev submitted similar patch fixing MIPS]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Unfortunately, I missed a catch when reviewing the patch committed as
201bffa4. Here is the fix to the currently broken handling of sleeping
devices. In particular, this is required to get the disk shock
protection code working again.
Reported-by: Christian Thaeter <ct@pipapo.org>
Cc: stable@kernel.org
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Start a new device recognition if someone writes to sysfs online attribute
of a boxed ccw device. The current test will fail, since cu_type != 0
for devices which were recognized before.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Return -EAGAIN on writes to sysfs online attribute if the corresponding
ccw device is in transient state.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a ccw device did not respond in time during internal io, we set it
into boxed state. With this patch we have the following behaviour:
* the ccw driver will get a notification if the device was online and
goes into the boxed state
* if the device was disconnected and got boxed nothing special is to be
done (it will be handled in reprobing later)
* if the device got boxed while initial sensing it will be unregistered
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce ccw_device_schedule_sch_unregister as a wrapper for queuing
ccw_device_call_sch_unregister on the slow_path_wq. This wrapper
will be used in the next patch.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Wake up even on failed device recognition, since this may be triggered
from a user trying to force a device online. With this patch a write
to the online sysfs attribute will not block for ever but return with
-EAGAIN in this case.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With "cpumask: update irq_desc to use cpumask_var_t"
we get this build failure on s390:
CC drivers/char/sysrq.o
In file included from drivers/char/sysrq.c:38:
include/linux/irq.h: In function 'init_alloc_desc_masks':
include/linux/irq.h:442: error: dereferencing pointer to incomplete type
drivers/char/sysrq.c should include interrupt.h instead of irq.h.
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
At present it is not possible for machine constraints to disable
regulators which have been left on when the system starts, for example
as a result of fixed default configurations in hardware. This means that
power may be wasted by these regulators if they are not in use.
Provide intial support for this with a late_initcall which will disable
any unused regulators if the machine has enabled this feature by calling
regulator_has_full_constraints(). If this has not been called then print
a warning to encourage users to fully specify their constraints so that
we can change this to be the default behaviour in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Don't set use_count for regulators that are enabled at boot since this
stops the supply being disabled by well-behaved consumers which do
balanced enables and disabled. Any consumers which don't do disables
which are not matched by enables are unable to share regulators - shared
regulators are the common case so the API should facilitate them.
Consumers that want to disable regulators that are enabled when they
start have two options:
- Do a regulator_enable() prior to the disable to bring the use count
in sync with the hardware state; this will ensure that if the
regulator was enabled by another driver then this consumer will play
nicely with it.
- Use regulator_force_disable(); this explicitly bypasses any checks
done by the core and documents the inability of the driver to share
the supply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add VPLL2 to the set of twl4030-family regulators exposed for
use by various drivers. It's commonly used to power the digital
video outputs (e.g. LCD or DVI displays) on OMAP3 systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix some refcounting issues in the regulator framework, supporting
regulator_disable() for regulators that were enabled at boot time
via machine constraints:
- Update those regulators' usecounts after enabling, so they
can cleanly be disabled at that level.
- Remove the problematic per-consumer usecount, so there's
only one level of enable/disable.
Buggy consumers could notice different bug symptoms. The main
example would be refcounting bugs; also, any (out-of-tree) users
of the experimental regulator_set_optimum_mode() stuff which
don't call it when they're done using a regulator.
This is a net minor codeshrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The consumer can print a message if required, some consumers may have
optional regulators and wish to downgrade the logging for them or ignore
their absence.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than incrementing the reference count for boot_on regulators
(which prevents them being disabled later on) simply force the
regulator to be enabled when applying the constraints. Previously
boot_on was essentially equivalent to always_on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Implement the recently added voltage step listing API for the WM835x
DCDCs and LDOs. DCDCs can use values up to 0x66, LDOs can use the full
range of values in the mask. Both masks are the lower bits of the
register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The VAUX4 voltage table scrolls onto a second page in many versions
of the TWL4030 family manuals. This doesn't mean we should ignore
those values! Some boards use the (fully supported) 2.8V setting.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Specifying voltage constraints is optional (and only needed if the
consumer is allowed to change the voltage) so don't complain unless
a voltage has been specified.
Also avoid surprises with a dangling else while we're here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.
These calls are intended to be used by MMC host adapters
using at least one regulator per host. Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Update previously-posted twl4030 regulator driver to export
supported voltages to upper layers using a new mechanism.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support most of the LDO regulators in the twl4030 family chips.
In the case of LDOs supporting MMC/SD, the voltage controls are
used; but in most other cases, the regulator framework is only
used to enable/disable a supplies, conserving power when a given
voltage rail is not needed.
The drivers/mfd/twl4030-core.c code already sets up the various
regulators according to board-specific configuration, and knows
that some chips don't provide the full set of voltage rails.
The omitted regulators are intended to be under hardware control,
such as during the hardware-mediated system powerup, powerdown,
and suspend states. Unless/until software hooks are known to
be safe, they won't be exported here.
These regulators implement the new get_status() operation, but
can't realistically implement get_mode(); the status output is
effectively the result of a vote, with the relevant hardware
inputs not exposed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a basic mechanism for regulators to report the discrete
voltages they support: list_voltage() enumerates them using
selectors numbered from 0 to an upper bound.
Use those methods to force machine-level constraints into bounds.
(Example: regulator supports 1.8V, 2.4V, 2.6V, 3.3V, and board
constraints for that rail are 2.0V to 3.6V ... so the range of
voltages is then 2.4V to 3.3V on this board.)
Export those voltages to the regulator consumer interface, so for
example regulator hooked up to an MMC/SD/SDIO slot can report the
actual voltage options available to cards connected there.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM835x regulators need a different register checking for force
mode on each DCDC. Previously the force mode status for DCDC1 was
checked.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is useful when wishing to run in a fixed operating mode that isn't
the default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Update the documentation to suggest the use of datasheet names for
the supplies requested by regulator consumers. Doing this makes it
easier to tie the design for a given platform up with the requirements
of the driver for a consumer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently regulator_unregister does not clear regulator <--> consumer
mapping.
This patch introduces unset_regulator_supplies that clear the map.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Commit 872ed3fe176833f7d43748eb88010da4bbd2f983 caused regulator drivers
to take the struct regulator_dev lock themselves which requires that the
struct be visible to them. Band aid this by making the struct visible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This allows users to enable or disable support for these regulators at
build time as they can for other regulators rather than having platforms
force the regulators to be built in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Previously it was not possible to do so, making it impossible for
machines to configure the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than having the regulator init data read from the platform_data
member of the struct device that is registered for the regulator make
the init data an explict argument passed in when registering. This
allows drivers to use the platform data for their own purposes if they
wish.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Regulator: Push lock out of _notifier_call_chain and into caller functions
(side effect of fixing deadlock in regulator_force_disable)
+ Add a voltage changed event.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Based on previous LKML discussions:
* Update docs for regulator sysfs class attributes to highlight
the fact that all current attributes are intended to be control
inputs, including notably "state" and "opmode" which previously
implied otherwise.
* Define a new regulator driver get_status() method, which is the
first method reporting regulator outputs instead of inputs.
It can report on/off and error status; or instead of simply
"on", report the actual operating mode.
For the moment, this is a sysfs-only interface, not accessible to
regulator clients. Such clients can use the current notification
interfaces to detect errors, if the regulator reports them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Minor cleanup to the regulator set_mode sysfs support:
switch to sysfs_streq() in set_mode(), which is also
a code shrink. Use the same strings that get_mode()
uses, shrinking data too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We currently update the metadata :
1/ every 3Megabytes
2/ When the place we will write new-layout data to is recorded in
the metadata as still containing old-layout data.
Rule one exists to avoid having to re-do too much reshaping in the
face of a crash/restart. So it should really be time based rather
than size based. So change it to "every 10 seconds".
Rule two turns out to be too harsh when restriping an array
'in-place', as in that case the metadata much be updates for every
stripe.
For the in-place update, it can only possibly be safe from a crash if
some user-space program data a backup of every e.g. few hundred
stripes before allowing them to be reshaped. In that case, the
constant metadata update is pointless.
So only update the metadata if the new metadata will report that the
end of the 'old-layout' data is beyond where we are currently
writing 'new-layout' data.
Signed-off-by: NeilBrown <neilb@suse.de>
... and to be certain the that make_request doesn't wait forever,
add a 'wake_up' when ->reshape_progress has been set to MaxSector
Signed-off-by: NeilBrown <neilb@suse.de>
This was only needed when the code was experimental. Most of it
is well tested now, so the option is no longer useful.
Signed-off-by: NeilBrown <neilb@suse.de>
When we are reshaping an array, it is very important that we read
the data from a particular sector offset before writing new data
at that offset.
In most cases when growing or shrinking an array we read long before
we even consider writing. But when restriping an array without
changing it size, there is a small possibility that we might have
some data to available write before the read has happened at the same
location. This would require some stripes to be in cache already.
To guard against this small possibility, we check, before writing,
that the 'old' stripe at the same location is not in the process of
being read. And we ensure that we mark all 'source' stripes as such
before allowing new 'destination' stripes to proceed.
Signed-off-by: NeilBrown <neilb@suse.de>
When no resync if happening, both of these files currently have
meaningless values (is slightly different ways).
Change them to "none" in that case.
Signed-off-by: NeilBrown <neilb@suse.de>
If an array has 3 or more devices, we allow the chunksize or layout
to be changed and when a reshape starts, we use these as the 'new'
values.
Signed-off-by: NeilBrown <neilb@suse.de>
This ensures that even when old and new stripes are overlapping,
we will try to read all of the old before having to write any
of the new.
Signed-off-by: NeilBrown <neilb@suse.de>
Add "prev_chunk" to raid5_conf_t, similar to "previous_raid_disks", to
remember what the chunk size was before the reshape that is currently
underway.
This seems like duplication with "chunk_size" and "new_chunk" in
mddev_t, and to some extent it is, but there are differences.
The values in mddev_t are always defined and often the same.
The prev* values are only defined if a reshape is underway.
Also (and more significantly) the raid5_conf_t values will be changed
at the same time (inside an appropriate lock) that the reshape is
started by setting reshape_position. In contrast, the new_chunk value
is set when the sysfs file is written which could be well before the
reshape starts.
Signed-off-by: NeilBrown <neilb@suse.de>
During a raid5 reshape, we have some stripes in the cache that are
'before' the reshape (and are still to be processed) and some that are
'after'. They are currently differentiated by having different
->disks values as the only reshape current supported involves changing
the number of disks.
However we will soon support reshapes that do not change the number
of disks (chunk parity or chunk size). So make the difference more
explicit with a 'generation' number.
Signed-off-by: NeilBrown <neilb@suse.de>
When reshaping a raid5 to have fewer devices, we work from the end of
the array to the beginning.
md_do_sync gives addresses to sync_request that go from the beginning
to the end. So largely ignore them use the internal state variable
"reshape_progress" to keep track of what to do next.
Never allow the size to be reduced below the minimum (4 for raid6,
3 otherwise).
We require that the size of the array has already been reduced before
the array is reshaped to a smaller size. This is because simply
reducing the size is an easily reversible operation, while the reshape
is immediately destructive and so is not reversible for the blocks at
the ends of the devices.
Thus to reshape an array to have fewer devices, you must first write
an appropriately small size to md/array_size.
When reshape finished, we remove any drives that are no longer
needed and fix up ->degraded.
Signed-off-by: NeilBrown <neilb@suse.de>
When reducing the number of devices in a raid4/5/6, the reshape
process has to start at the end of the array and work down to the
beginning. So we need to handle expand_progress and expand_lo
differently.
This patch renames "expand_progress" and "expand_lo" to avoid the
implication that anything is getting bigger (expand->reshape) and
every place they are used, we make sure that they are used the right
way depending on whether delta_disks is positive or negative.
Signed-off-by: NeilBrown <neilb@suse.de>
Currently raid5 (the only module that supports restriping)
notices that the reshape has finished be sync_request being
given a large value, and handles any cleanup them.
This patch changes it so md_check_recovery calls into an
explicit finish_reshape method as well.
The clean-up from sync_request can do things that need to be
done promptly, typically things local to the raid5_conf_t
structure.
The "finish_reshape" method is called under the mddev_lock
so it can do things involving reconfiguring the device.
This allows us to get rid of md_set_array_sectors_locked, which
would have caused a deadlock if you tried to stop and array
while a reshape was happening.
Signed-off-by: NeilBrown <neilb@suse.de>
This is the first of four patches which combine to allow md/raid5 to
reduce the number of devices in the array by restriping the data over
a subset of the devices.
If the number of disks in a raid4/5/6 is being reduced, then the
default size must be based on the new number, not the old number
of devices.
In general, it should be based on the smaller of new and old.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the raid6 data processing routines into a standalone module
(raid6_pq) to prepare them to be called from async_tx wrappers and other
non-md drivers/modules. This precludes a circular dependency of raid456
needing the async modules for data processing while those modules in
turn depend on raid456 for the base level synchronous raid6 routines.
To support this move:
1/ The exportable definitions in raid6.h move to include/linux/raid/pq.h
2/ The raid6_call, recovery calls, and table symbols are exported
3/ Extra #ifdef __KERNEL__ statements to enable the userspace raid6test to
compile
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Allow userspace to set the size of the array according to the following
semantics:
1/ size must be <= to the size returned by mddev->pers->size(mddev, 0, 0)
a) If size is set before the array is running, do_md_run will fail
if size is greater than the default size
b) A reshape attempt that reduces the default size to less than the set
array size should be blocked
2/ once userspace sets the size the kernel will not change it
3/ writing 'default' to this attribute returns control of the size to the
kernel and reverts to the size reported by the personality
Also, convert locations that need to know the default size from directly
reading ->array_sectors to <pers>_size. Resync/reshape operations
always follow the default size.
Finally, fixup other locations that read a number of 1k-blocks from
userspace to use strict_blocks_to_sectors() which checks for unsigned
long long to sector_t overflow and blocks to sectors overflow.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Get personalities out of the business of directly modifying
->array_sectors. Lays groundwork to introduce policy on when
->array_sectors can be modified.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for giving userspace control over ->array_sectors we need
to be able to retrieve the 'default' size, and the 'anticipated' size
when a reshape is requested. For personalities that do not reshape emit
a warning if anything but the default size is requested.
In the raid5 case we need to update ->previous_raid_disks to make the
new 'default' size available.
Reviewed-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Hello,
I found a typo Bosto"m" in FSF address.
And I am checking around linux source code.
Here is the only place which uses Bosto"m" (not Boston).
Signed-off-by: Atsushi SAKAI <sakaia@jp.fujitsu.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a raid6 is still in the layout that comes from converting raid5
into a raid6. this will allow us to convert it back again.
Signed-off-by: NeilBrown <neilb@suse.de>
2-drive raid5's aren't very interesting. But if you are converting
a raid1 into a raid5, you will at least temporarily have one. And
that it a good time to set the layout/chunksize for the new RAID5
if you aren't happy with the defaults.
layout and chunksize don't actually affect the placement of data
on a 2-drive raid5, so we just do some internal book-keeping.
Signed-off-by: NeilBrown <neilb@suse.de>
Implement this for RAID6 to be able to 'takeover' a RAID5 array. The
new RAID6 will use a layout which places Q on the last device, and
that device will be missing.
If there are any available spares, one will immediately have Q
recovered onto it.
Signed-off-by: NeilBrown <neilb@suse.de>
To be able to change the 'level' of an md/raid array, we need to
suspend the device so that no requests are active - then move some
pointers around etc.
The code already keeps counts of active requests and the ->quiesce
function can be used to wait until those counts hit zero.
However the quiesce function blocks new requests once they are all
ready 'inside' the personality module, and that is too late if we want
to replace the personality modules.
So make all md requests come in through a common md_make_request
function that keeps track of how many requests have entered the
modules but may not yet be on the internal reference counts.
Allow md_make_request to be blocked when we want to suspend the
device, and make it possible to wait for all those in-transit requests
to be added to internal lists so that ->quiesce can wait for them.
There is still a problem that when a request completes, we drop the
ref count inside the personality code so there is a short time between
when the refcount hits zero, and when the personality code is no
longer being used.
The personality code never blocks (schedule or spinlock) between
dropping the refcount and exiting the routine, so this should be safe
(as put_module calls synchronize_sched() before unmapping the module
code).
Signed-off-by: NeilBrown <neilb@suse.de>
Mostly md_unregister_thread is only called when we know that the
thread is NULL, but sometimes we need to check first. It is safer
to put the check inside md_unregister_thread itself.
Signed-off-by: NeilBrown <neilb@suse.de>
.. so that the code to create the private data structures is separate.
This will help with future code to change the level of an active
array.
Signed-off-by: NeilBrown <neilb@suse.de>
When an md array is undergoing a change, we have new_* fields that
show the new values.
When no change is happening, it is least confusing if these have
the same value as the normal fields.
This is true in most cases, but not when the values are set via sysfs.
So fix this up.
A subsequent patch will BUG_ON if these things aren't consistent.
Signed-off-by: NeilBrown <neilb@suse.de>
DDF requires RAID6 calculations over different devices in a different
order.
For md/raid6, we calculate over just the data devices, starting
immediately after the 'Q' block.
For ddf/raid6 we calculate over all devices, using zeros in place of
the P and Q blocks.
This requires unfortunately complex loops...
Signed-off-by: NeilBrown <neilb@suse.de>
DDF uses different layouts for P and Q blocks than current md/raid6
so add those that are missing.
Also add support for RAID6 layouts that are identical to various
raid5 layouts with the simple addition of one device to hold all of
the 'Q' blocks.
Finally add 'raid5' layouts to match raid4.
These last to will allow online level conversion.
Note that this does not provide correct support for DDF/raid6 yet
as the order in which data blocks are summed to produce the Q block
is significant and different between current md code and DDF
requirements.
Signed-off-by: NeilBrown <neilb@suse.de>
Rather than passing 'pd_idx' and 'qd_idx' to be filled in, pass
a 'struct stripe_head *' and fill in the relevant fields. This is
more extensible.
Signed-off-by: NeilBrown <neilb@suse.de>
Code currently assumes that the devices in a raid6 stripe are
0 1 ... N-1 P Q
in some rotated order. We will shortly add new layouts in which
this strict pattern is broken.
So remove this expectation. We still assume that the data disks
are roughly in-order. However P and Q can be inserted anywhere within
that order.
Signed-off-by: NeilBrown <neilb@suse.de>
This similar to the recent change to get_active_stripe.
There is no functional change, just come rearrangement to make
future patches cleaner.
Signed-off-by: NeilBrown <neilb@suse.de>
Rather than passing 'pd_idx' and 'disks' to these functions, just pass
'previous' which tells whether to use the 'previous' or 'current'
geometry during a reshape, and let init_stripe calculate
disks and pd_idx and anything else it might need.
This is not a substantial simplification and even adds a division.
However we will shortly be adding more complexity to init_stripe
to handle more interesting 'reshape' activities, and without this
change, the interface to these functions would get very complex.
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the "size" field of struct mdk_rdev_s to
"sectors" and changes this field to store sectors instead of
blocks.
All users of this field, linear.c, raid0.c and md.c, are fixed up
accordingly which gets rid of many multiplications and divisions.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the "size" field of struct mddev_s to "dev_sectors"
and stores the number of 512-byte sectors instead of the number of
1K-blocks in it.
All users of that field, including raid levels 1,4-6,10, are adjusted
accordingly. This simplifies the code a bit because it allows to get
rid of a couple of divisions/multiplications by two.
In order to make checkpatch happy, some minor coding style issues
have also been addressed. In particular, size_store() now uses
strict_strtoull() instead of simple_strtoull().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
When a drive is added to an array using ADD_NEW_DISK, there are two
places we can get certain flags from: the metadata on the disk or the
flags passed through the IOCTL.
For the WriteMostly flag (aka MD_DISK_WRITEMOSTLY) we take the value
from either of those sources depending on if it is set (i.e. we
effectively 'or' the two sources together).
This makes it awkward to clear, and is at best inconsistent.
As documented code (in mdadm) requires that setting
MD_DISK_WRITEMOSTLY in the ioctl will be effective, we resolve the
inconsistency by always using the value for this flag from the ioctl,
and ignoring the value on disk.
Signed-off-by: NeilBrown <neilb@suse.de>
Version 1.x metadata has the ability to record the status of a
partially completed drive recovery.
However we only update that record on a clean shutdown.
It would be nice to update it on unclean shutdowns too, particularly
when using a bitmap that removes much to the 'sync' effort after an
unclean shutdown.
One complication with checkpointing recovery is that we only know
where we are up to in terms of IO requests started, not which ones
have completed. And we need to know what has completed to record
how much is recovered. So occasionally pause the recovery until all
submitted requests are completed, then update the record of where
we are up to.
When we have a bitmap, we already do that pause occasionally to keep
the bitmap up-to-date. So enhance that code to record the recovery
offset and schedule a superblock update.
And when there is no bitmap, just pause 16 times during the resync to
do a checkpoint.
'16' is a fairly arbitrary number. But we don't really have any good
way to judge how often is acceptable, and it seems like a reasonable
number for now.
Signed-off-by: NeilBrown <neilb@suse.de>
This makes the includes more explicit, and is preparation for moving
md_k.h to drivers/md/md.h
Remove include/raid/md.h as its only remaining use was to #include
other files.
Signed-off-by: NeilBrown <neilb@suse.de>
.. as they are part of the user-space interface.
Also move MdpMinorShift into there so we can remove duplication.
Lastly move mdp_major in. It is less obviously part of the user-space
interface, but do_mounts_md.c uses it, and it is acting a bit like
user-space.
Signed-off-by: NeilBrown <neilb@suse.de>
Move the headers with the local structures for the disciplines and
bitmap.h into drivers/md/ so that they are more easily grepable for
hacking and not far away. md.h is left where it is for now as there
are some uses from the outside.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Use the -y variables instead of the old -objs so we can easily add
conditional objects to the modules. Also always use += to add
subobjects to avoid problems when placing additional objects in
some place in the file.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
MAJOR_NR was only required for magic in linux/blk.h in 2.4 or earlier
kernels, so no need to keep it around.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: NeilBrown <neilb@suse.de>
md: Add support for data integrity to MD
If all subdevices support the same protection format the MD device is
flagged as integrity capable.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we add some spares to an array and start recovery, and we have
a bitmap which is stored 'internally' on all devices, we call
bitmap_write_all to make sure the bitmap is correct on the new
device(s).
However that doesn't work as write_sb_page only writes to
'In_sync' devices, and devices undergoing recovery are not
'In_sync' until recovery finishes.
So extend write_sb_page (actually next_active_rdev) to include devices
that are under recovery.
Signed-off-by: NeilBrown <neilb@suse.de>
It is safe to clear a bit from the write-intent bitmap for a raid1
if we know the data has been written to all devices, which is
what the current test does.
But it is not always safe to update the 'events_cleared' counter in
that case. This is because one request could complete successfully
after some other request has partially failed.
So simply disable the clearing and updating of events_cleared whenever
the array is degraded. This might end up not clearing some bits that
could safely be cleared, but it is safest approach.
Note that the bug fixed here did not risk corrupting data by letting
the array get out-of-sync. Rather it meant that when a device is
removed and re-added to the array, it might incorrectly require a full
recovery rather than just recovering based on the bitmap.
Signed-off-by: NeilBrown <neilb@suse.de>
md currently insists that the chunk size used for write-intent
bitmaps (the amount of data that corresponds to one chunk)
be at least one page.
The reason for this restriction is lost in the mists of time,
but a review of the code (and a vague memory) suggests that the only
problem would be related to resync. Resync tries very hard to
work in multiples of a page, but also needs to sync with units
of a bitmap_chunk too.
This connection comes out in the bitmap_start_sync call.
So change bitmap_start_sync to always work in multiples of a page.
If the bitmap chunk size is less that one page, we flag multiple
chunks as 'syncing' and generally make them all appear to the
resync routines like one chunk.
All other code either already works with data ranges that could
span multiple chunks, or explicitly only cares about a single chunk.
Signed-off-by: Neil Brown <neilb@suse.de>
There are two problems with is_mddev_idle.
1/ sync_io is 'atomic_t' and hence 'int'. curr_events and all the
rest are 'long'.
So if sync_io were to wrap on a 64bit host, the value of
curr_events would go very negative suddenly, and take a very
long time to return to positive.
So do all calculations as 'int'. That gives us plenty of precision
for what we need.
2/ To initialise rdev->last_events we simply call is_mddev_idle, on
the assumption that it will make sure that last_events is in a
suitable range. It used to do this, but now it does not.
So now we need to be more explicit about initialisation.
Signed-off-by: NeilBrown <neilb@suse.de>
drivers/parisc/iosapic.c:717: error: incompatible types in assignment
irq_desc::affinity was changed from cpumask_t to cpumask_var_t in
7f7ace0cda (cpumask: update irq_desc to use cpumask_var_t)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
- depending on machine type, blink all leds or just the loadavg
leds twice a second on oops.
- cancel_rearming_delayed_workqueue() is obsolete,
use cancel_delayed_work_sync() instead
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
wireless: remove duplicated .ndo_set_mac_address
netfilter: xtables: fix IPv6 dependency in the cluster match
tg3: Add GRO support.
niu: Add GRO support.
ucc_geth: Fix use-after-of_node_put() in ucc_geth_probe().
gianfar: Fix use-after-of_node_put() in gfar_of_init().
kernel: remove HIPQUAD()
netpoll: store local and remote ip in net-endian
netfilter: fix endian bug in conntrack printks
dmascc: fix incomplete conversion to network_device_ops
gso: Fix support for linear packets
skbuff.h: fix missing kernel-doc
ni5010: convert to net_device_ops
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest-and-virtio:
lguest: barrier me harder
lguest: use bool instead of int
lguest: use KVM hypercalls
lguest: wire up pte_update/pte_update_defer
lguest: fix spurious BUG_ON() on invalid guest stack.
virtio: more neatening of virtio_ring macros.
virtio: fix BAD_RING, START_US and END_USE macros
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (fschmd) Add support for the FSC Hades IC
hwmon: (fschmd) Add support for the FSC Syleus IC
i2c-i801: Instantiate FSC hardware montioring chips
dmi: Let dmi_walk() users pass private data
hwmon: Define a standard interface for chassis intrusion detection
Move the pcf8591 driver to hwmon
hwmon: (w83627ehf) Only expose in6 or temp3 on the W83667HG
hwmon: (w83627ehf) Add support for W83667HG
hwmon: (w83627ehf) Invert fan pin variables logic
hwmon: (hdaps) Fix Thinkpad X41 axis inversion
hwmon: (hdaps) Allow inversion of separate axis
hwmon: (ds1621) Clean up documentation
hwmon: (ds1621) Avoid unneeded register access
hwmon: (ds1621) Clean up register access
hwmon: (ds1621) Reorder code statements
* 'proc-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/adobriyan/proc:
Revert "proc: revert /proc/uptime to ->read_proc hook"
proc 2/2: remove struct proc_dir_entry::owner
proc 1/2: do PDE usecounting even for ->read_proc, ->write_proc
proc: fix sparse warnings in pagemap_read()
proc: move fs/proc/inode-alloc.txt comment into a source file
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PCI PM: Make pci_prepare_to_sleep() disable wake-up if needed
radeonfb: Use __pci_complete_power_transition()
PCI PM: Introduce __pci_[start|complete]_power_transition() (rev. 2)
PCI PM: Restore config spaces of all devices during early resume
PCI PM: Make pci_set_power_state() handle devices with no PM support
PCI PM: Put devices into low power states during late suspend (rev. 2)
PCI PM: Move pci_restore_standard_config to pci-driver.c
PCI PM: Use pci_set_power_state during early resume
PCI PM: Consistently use variable name "error" for pm call return values
kexec: Change kexec jump code ordering
PM: Change hibernation code ordering
PM: Change suspend code ordering
PM: Rework handling of interrupts during suspend-resume
PM: Introduce functions for suspending and resuming device interrupts
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (53 commits)
drm: detect hdmi monitor by hdmi identifier (v3)
drm: drm_fops.c unlock missing on error path
drm: reorder struct drm_ioctl_desc to save space on 64 bit builds
radeon: add some new pci ids
drm: read EDID extensions from monitor
drm: Use a little stash on the stack to avoid kmalloc in most DRM ioctls.
drm/radeon: add regs required for occlusion queries support
drm/i915: check the return value from the copy from user
drm/radeon: fix logic in r600_page_table_init() to match ati_gart
drm/radeon: r600 ptes are 64-bit, cleanup cleanup function.
drm/radeon: don't call irq changes on r600 suspend/resume
drm/radeon: fix r600 writeback across suspend/resume
drm/radeon: fix r600 writeback setup.
drm: fix warnings about new mappings in info code.
drm/radeon: NULL noise: drivers/gpu/drm/radeon/radeon_*.c
drm/radeon: fix r600 pci mapping calls.
drm/radeon: r6xx/r7xx: fix possible oops in r600_page_table_cleanup()
radeon: call the correct idle function, logic got inverted.
drm/radeon: RS600: fix interrupt handling
drm/r600: fix rptr address along lines of previous fixes to radeon.
...
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
dma-debug: make memory range checks more consistent
dma-debug: warn of unmapping an invalid dma address
dma-debug: fix dma_debug_add_bus() definition for !CONFIG_DMA_API_DEBUG
dma-debug/x86: register pci bus for dma-debug leak detection
dma-debug: add a check dma memory leaks
dma-debug: add checks for kernel text and rodata
dma-debug: print stacktrace of mapping path on unmap error
dma-debug: Documentation update
dma-debug: x86 architecture bindings
dma-debug: add function to dump dma mappings
dma-debug: add checks for sync_single_sg_*
dma-debug: add checks for sync_single_range_*
dma-debug: add checks for sync_single_*
dma-debug: add checking for [alloc|free]_coherent
dma-debug: add add checking for map/unmap_sg
dma-debug: add checking for map/unmap_page/single
dma-debug: add core checking functions
dma-debug: add debugfs interface
dma-debug: add kernel command line parameters
dma-debug: add initialization code
...
Fix trivial conflicts due to whitespace changes in arch/x86/kernel/pci-nommu.c
If the device is not supposed to wake up the system, ie. when
device_may_wakeup(&dev->dev) returns 'false', pci_prepare_to_sleep()
should pass 'false' to pci_enable_wake() so that it calls the
platform to disable the wake-up capability of the device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use __pci_complete_power_transition() to finalize the transition into
D2 after programming the PMCSR of the device directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The radeonfb driver needs to program the device's PMCSR directly due
to some quirky hardware it has to handle (see
http://bugzilla.kernel.org/show_bug.cgi?id=12846 for details) and
after doing that it needs to call the platform (usually ACPI) to
finish the power transition of the device. Currently it uses
pci_set_power_state() for this purpose, however making a specific
assumption about the internal behavior of this function, which has
changed recently so that this assumption is no longer satisfied.
For this reason, introduce __pci_complete_power_transition() that may
be called by the radeonfb driver to complete the power transition of
the device. For symmetry, introduce __pci_start_power_transition().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At present the configuration spaces of PCI devices that have no
drivers or no PM support in the drivers (either legacy or through a
pm object) are not saved during suspend and, consequently, they are
not restored during resume. This generally may lead to the state of
the system being slightly inconsistent after the resume, so it's
better to save and restore the configuration spaces of these devices
as well.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a problem with PCI devices without any PM support (either
native or through the platform) that pci_set_power_state() always
returns error code for them, even if they are being put into D0.
However, such devices are always in D0, so pci_set_power_state()
should return success when attempting to put such a device into D0.
It also should update the current_state field for these devices as
appropriate. This modification is necessary so that the standard
configuration registers of these devices are successfully restored by
pci_restore_standard_config() during the "early" phase of resume.
In addition, pci_set_power_state() should check the value of
current_state before calling the platform to change the power state
of the device to avoid doing that unnecessarily.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Once we have allowed timer interrupts to be enabled during the late
phase of suspending devices, we are now able to use the generic
pci_set_power_state() to put PCI devices into low power states at
that time. We can also use some related platform callbacks, like the
ones preparing devices for wake-up, during the late suspend.
Doing this will allow us to avoid the race condition where a device
using shared interrupts is put into a low power state with interrupts
enabled and then an interrupt (for another device) comes in and
confuses its driver. At the same time, devices that don't support
the native PCI PM or that require some additional, platform-specific
operations to be carried out to put them into low power states will
be handled as appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move pci_restore_standard_config() from pci.c to pci-driver.c and
make it static.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Once we have allowed timer interrupts to be enabled during the early
phase of resuming devices, we are now able to use the generic
pci_set_power_state() to put PCI devices into D0 at that time. Then,
the platform-specific PM code will have a chance to handle devices
that don't implement the native PCI PM or that require some
additional, platform-specific operations to be carried out to power
them up. Also, by doing this we can simplify the code quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
I noticed two functions use a variable "i" to store the return value of PM
function calls while the rest of the file uses "error". As "i" normally
indicates a counter of some sort it seems better to keep this consistent.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use the functions introduced in by the previous patch,
suspend_device_irqs(), resume_device_irqs() and check_wakeup_irqs(),
to rework the handling of interrupts during suspend (hibernation) and
resume. Namely, interrupts will only be disabled on the CPU right
before suspending sysdevs, while device drivers will be prevented
from receiving interrupts, with the help of the new helper function,
before their "late" suspend callbacks run (and analogously during
resume).
In addition, since the device interrups are now disabled before the
CPU has turned all interrupts off and the CPU will ACK the interrupts
setting the IRQ_PENDING bit for them, check in sysdev_suspend() if
any wake-up interrupts are pending and abort suspend if that's the
case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Many thanks to Fujitsu Siemens Computers for providing docs and a
machine to test the driver on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Detect various FSC hwmon IC's based on DMI tables and then let
the i2c-i801 driver instantiate the i2c client devices. Note that
some of the info in the added table is indentical for all rows, still
this is kept in the table to keep the code general and thus (hopefully)
easily extensible in the future.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.
If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
The pin for in6 and temp3 is shared on the W83667HG, so only one of
these features can be supported on any given system. Let the driver
select which one depending on the temp3 disabled bit.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.
At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use positive logic for fan pin variables (variable is set if pin is
used for fan), instead of negative logic which is error prone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Gong Jun <JGong@nuvoton.com>
Fix for kernel.org bug #7154: hdaps inversion of actual Thinkpad
X41's Y-axis.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix for kernel.org bug #7154: hdaps inversion of each axis. This
version is based on the work from Michael Ruoss <miruoss@student.ethz.ch>.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Register access over SMBus isn't cheap, so avoid register access where
possible:
* Only write back the configuration register if it changed.
* Don't refresh the register cache when we don't have to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Fix a few oddities in how the ds1621 driver accesses the registers:
* We don't need a wrapper to access the configuration register.
* Check for error before calling swab16. Error checking isn't
complete yet, but that's a start.
* Device-specific read functions should never be called during
detection, as by definition we don't know what device we are talking
to at that point.
* Likewise, don't assume that register reads succeed during detection.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reorder the ds1621 driver code so that we can get rid of forward
function declarations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Impact: fix bug
This patch reworks the nv_msi_ht_cap_quirk() and will only try to avoid
to enable ht_msi on device following that root dev, and don't touch that
root dev, but only do that trick with end_device on the chain.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'x86-stage-3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (190 commits)
Revert "cpuacct: reduce one NULL check in fast-path"
Revert "x86: don't compile vsmp_64 for 32bit"
x86: Correct behaviour of irq affinity
x86: early_ioremap_init(), use __fix_to_virt(), because we are sure it's safe
x86: use default_cpu_mask_to_apicid for 64bit
x86: fix set_extra_move_desc calling
x86, PAT, PCI: Change vma prot in pci_mmap to reflect inherited prot
x86/dmi: fix dmi_alloc() section mismatches
x86: e820 fix various signedness issues in setup.c and e820.c
x86: apic/io_apic.c define msi_ir_chip and ir_ioapic_chip all the time
x86: irq.c keep CONFIG_X86_LOCAL_APIC interrupts together
x86: irq.c use same path for show_interrupts
x86: cpu/cpu.h cleanup
x86: Fix a couple of sparse warnings in arch/x86/kernel/apic/io_apic.c
Revert "x86: create a non-zero sized bm_pte only when needed"
x86: pci-nommu.c cleanup
x86: io_delay.c cleanup
x86: rtc.c cleanup
x86: i8253 cleanup
x86: kdebugfs.c cleanup
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (21 commits)
MIPS: Alchemy: PB1200: use SMC91X platform data.
MIPS: Alchemy: MIPS hazard workarounds are not required.
MIPS: Alchemy: provide cpu feature overrides.
MIPS: Alchemy: unify CPU model constants.
MIPS: Make a needlessly global symbol static in arch/mips/kernel/smp.c
MIPS: Fix global namespace pollution in arch/mips/kernel/smp-up.c
MIPS: Malta: make a needlessly global integer variable static
MIPS: Use BUG_ON() where possible.
MIPS: Convert obsolete irq_desc_t to struct irq_desc
MIPS: Enable GENERIC_HARDIRQS_NO__DO_IRQ for all platforms
MIPS: EMMA2RH: Set UART mapbase
MIPS: EMMA2RH: Use set_irq_chip_and_handler_name
MIPS: EMMA2RH: Use handle_edge_irq() handler for GPIO interrupts
MIPS: Mark Eins: Fix cascading interrupt dispatcher
MIPS: Au1000: convert to using gpiolib
MIPS: Stop using <asm-generic/int-l64.h>.
MIPS: Cavium: Add -Werror
MIPS: Makefile: Add simple make install target.
MIPS: Compat: Zero upper 32-bit of offset_high and offset_low.
MIPS: __raw_spin_lock() may spin forever on ticket wrap.
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (180 commits)
powerpc: clean up ssi.txt, add definition for fsl,ssi-asynchronous
powerpc/85xx: Add support for the "socrates" board (MPC8544).
powerpc: Fix bugs introduced by sysfs changes
powerpc: Sanitize stack pointer in signal handling code
powerpc: Add write barrier before enabling DTL flags
powerpc/83xx: Update ranges in gianfar node to match other dts
powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/85xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/83xx: Move gianfar mdio nodes under the ethernet nodes
powerpc/83xx: Add power management support for MPC837x boards
powerpc/mm: Introduce early_init_mmu() on 64-bit
powerpc/mm: Add option for non-atomic PTE updates to ppc64
powerpc/mm: Fix printk type warning in mmu_context_nohash
powerpc/mm: Rename arch/powerpc/kernel/mmap.c to mmap_64.c
powerpc/mm: Merge various PTE bits and accessors definitions
powerpc/mm: Tweak PTE bit combination definitions
powerpc/cell: Fix iommu exception reporting
powerpc/mm: e300c2/c3/c4 TLB errata workaround
powerpc/mm: Used free register to save a few cycles in SW TLB miss handling
powerpc/mm: Remove unused register usage in SW TLB miss handling
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (70 commits)
ide: keep track of number of bytes instead of sectors in struct ide_cmd
ide: remove ide_execute_pkt_cmd() (v2)
ide: add ->dma_timer_expiry method and remove ->dma_exec_cmd one (v2)
ide: set hwif->expiry prior to calling [__]ide_set_handler()
ide: use do_rw_taskfile() for ATA_CMD_PACKET commands
ide: pass command to ide_map_sg()
ide: remove ide_end_request()
ide: use ide_end_rq() in ide_complete_rq()
ide: pass number of bytes to complete to ide_complete_rq()
ide: remove BUG() from ide_complete_rq()
ide: move rq->errors quirk out from ide_end_request()
ide: pass error value to ide_complete_rq()
ide: sanitize ide_end_rq()
ide: add ide_end_rq() (v2)
ide: make ide_special_rq() BUG() on unknown requests
ide: sanitize ide_finish_cmd()
ide: use ide_complete_cmd() for REQ_UNPARK_HEADS
ide: use ide_complete_cmd() for head unload commands
ide: task_error() -> task_error_cmd()
ide: unify exit paths in task_pio_intr()
...
The tuner ops pointer wasn't set, so s_std never worked here.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_DRIVERIDs are no longer needed with v4l2_subdev and will be removed
from the kernel soon.
Cc: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No i2c modules are called with the V4L1 API anymore, so this can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace 'VIDIOC_' references in v4l i2c drivers by their new v4l2_subdev
callback names.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio and vbi parts still used an 'ioctl'-like interface. Replace this
with normal functions.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The audio and vbi functions where still called through an ioctl-like
interface, even though this is no longer needed with v4l2-subdev. Just
change each 'case' into a proper function and call that directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tuner-core.c contains a hack for cx88 board to prevent probing of certain
addresses:
/* HACK: Ignore 0x6b and 0x6f on cx88 boards.
* FusionHDTV5 RT Gold has an ir receiver at 0x6b
* and an RTC at 0x6f which can get corrupted if probed.
*/
With the new i2c API this hack no longer works. So instead change the
list of tuner probe addresses in the cx88 driver itself, which is much
more clean.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several i2c drivers still used v4l2_subdev_command, even though they were
converted to v4l2_subdev. Remove those unused .command callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda7432 is no longer used with the old-style i2c API, so I can remove
the support for that.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9875 is no longer used with the old-style i2c API, so I can remove
the support for that.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use wm8775 are now converted to v4l2_subdev, so I can remove
the support for the old-style i2c API.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert cx88 to use v4l2_subdev since the old i2c autoprobing mechanism
will be removed.
Added code to explicitly load tvaudio where needed. Also fix the rtc-isl1208
support: since that driver no longer supports autoprobing it has to be
loaded using the new i2c API.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use cx25840 are now converted to v4l2_subdev, so I can remove
the support for the old-style i2c API.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert this driver to v4l2_subdev. Note that currently the only card with
analog support in this driver is the HVR-1800. The analog tuner support in
this driver is limited to what is needed for this board. When analog support
is added for other cards, then the tuner load code will probably have to be
expanded to take care of those boards. For example, there is currently no
support for either radio tuners or tda9887 demods.
I'd like to thank Steven Toth for testing this on his HVR-1800.
Tested-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the firmware failed to be found the error message indicated
the incorrect filename.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When enumerating formats with VIDIOC_ENUM_FMT the uvcvideo driver does not
fill the reserved fields of the struct v4l2_fmtdesc with zeros as required by
V4L2 API revision 0.24 [1]. Add the missing initializations.
The patch was tested with v4l-test 0.10 [2] with CNF7129 webcam found on EeePC
901.
References:
[1] V4L2 API specification, revision 0.24
http://v4l2spec.bytesex.org/spec/r8367.htm
[2] v4l-test: Test environment for Video For Linux Two API
http://v4l-test.sourceforge.net/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces support for DVB-T for the following dibcom based card:
Elgato EyeTV DTT (USB-ID: 0fd9:0021)
Signed-off-by: Klaus Flittner <klaus@flittner.org>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the Yuan MC770 DVB-T (1164:0871).
Thanks to Xoan Loureiro.
Signed-off-by: Xoan Loureiro <x04n2.0@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the second part of the code cleanup changing the usb and pci-driver cores.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch cleans up the source code of the b2c2 flexcop-driver. It is the first of a total of two.
The code is now passing the checkpatch-script.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When resetting the PID-filter block a safety msleep(1) was injected. Now that the function is called from interrupt context, it was replaced with a udelay. It seems that this delay is not necessary at all, let's remove it for now and test a while.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a workaround in the i2c-code of the flexcop-driver to
fix support for SkyStar2 rev 2.7. There are not many devices out
there, that's why this bug was not revealed earlier.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
saa6588 is now only used through v4l2_subdev, so we can remove the old legacy
code.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Terratec Cinergy 600 TV MK3 supports the RDS decoder saa6588.
Add support to saa7134 for such devices.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
saa6588 can also be used by other drivers than just bttv. Move it to a
new RDS decoders category and add it as helper chip to bttv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since tda9875 support was merged into tvaudio the bttv driver no
longer needs tda9875 as helper driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since i2c autoprobing will disappear bttv needs to be converted to use
v4l2_subdev instead.
Without autoprobing the autoload module option has become obsolete. A warning
is generated if it is set, but it is otherwise ignored.
Since the bttv card definitions are of questionable value a new option was
introduced to allow the user to control which audio module is selected:
msp3400, tda7432 or tvaudio (or none at all).
By default bttv will use the card definitions and fallback on tvaudio as the
last resort.
If no audio device was found a warning is printed.
The saa6588 RDS device is now also explicitly probed since it is no longer
possible to autoprobe it. A new saa6588 module option was added to override
the card definition since I suspect more cards have this device than one
would guess from the card definitions.
Note that the probe addresses of the i2c modules are hardcoded in this
driver. Once all v4l drivers are converted to v4l2_subdev this will be
cleaned up. Such data belongs in an i2c driver header.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the tvaudio_remove function del_timer_sync(&chip->wt) is called.
However, chip->wt isn't always initialized depending on the type of
audio chip. Since del_timer_sync hangs when given an uninitialized timer
we should always initialize it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change allows bttv to use tvaudio for this device. Since this device
has the same i2c address as the tda9874 we need to support both in the same
tvaudio driver. This makes it possible for tvaudio to detect which chip is
used. Originally the tda9875 was only available in the dedicated tda9875
driver, but that makes life very hard for bttv since loading tvaudio might
misdetect a tda9875 as a tda9874.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mute control depends on CHIP_HAS_INPUTSEL, so test for that first.
The s/g_tuner code should check whether getmode/setmode is set at the
beginning instead of filling in the struct and discovering at
the end that this chip doesn't implement audiomodes after all (i.e. is
a simple muxer chip).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ->vidioc_(s|g|try|enum)_fmt_vid_cap() methods are only called on
VIDEO_CAPTURE buffers. Thus, there is no need to check or set the buffer's
'type' field since it must already be set to VIDEO_CAPTURE. Checking the
buffer type can be removed from zr364xx_vidioc_(s|g|try|enum)_fmt_vid_cap().
The v4l2 core code in v4l2_ioctl will zero out the structure the driver is
supposed to fill in for read-only ioctls. For read/write ioctls, all the
fields which aren't supplied from userspace will be zeroed out.
Zeroing code can be removed from zr364xx_vidioc_querycap(),
zr364xx_vidioc_enum_input(), zr364xx_vidioc_enum_fmt_vid_cap(), and
zr364xx_vidioc_g_fmt_vid_cap().
Cc: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core only allows buffer types for which the corresponding
->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(q|dq|query)buf() and vidioc_reqbufs().
Since this driver only defines ->vidioc_try_fmt_vid_cap() the checks can be
removed from vidioc_reqbufs(), vidioc_qbuf(), and vidioc_dqbuf().
The ->vidioc_(s|g|try|enum)_fmt_vid_cap() methods are only called on
VIDEO_CAPTURE buffers. Thus, there is no need to check or set the buffer's
'type' field since it must already be set to VIDEO_CAPTURE. So setting the
buffer type in vidioc_enum_fmt_vid_cap() can be removed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ->vidioc_(s|g|try|enum)_fmt_vid_cap() methods are only called on
VIDEO_CAPTURE buffers. Thus, there is no need to check or set the buffer's
'type' field since it must already be set to VIDEO_CAPTURE.
The v4l2-ioctl core only allows buffer types for which the corresponding
->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(q|dq|query)bufs() and vidioc_reqbufs().
Since this driver only defines ->vidioc_try_fmt_vid_cap() the checks can be
removed from vidioc_reqbufs(), vidioc_querybuf(), vidioc_qbuf(), and
vidioc_dqbuf(). Also, the buffer index is unsigned so it's not necessary
to check if it is less than zero.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ->vidioc_(s|g|try|enum)_fmt_vid_cap() methods are only called on
VIDEO_CAPTURE buffers. Thus, there is no need to check or set the 'type'
field since it must already be set to VIDEO_CAPTURE.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2 core code in v4l2_ioctl will zero out the structure the driver is
supposed to fill in for read-only ioctls. For read/write ioctls, all the
fields which aren't supplied from userspace will be zeroed out.
Zeroing code is removed from enum_input, g_tuner, g_frequency, querycap,
enum_fmt_vid_cap, g_fmt_vid_cap, and try_fmt_vid_cap.
The ->vidioc_(s|g|try|enum)_fmt_vid_cap() methods are only called on
VIDEO_CAPTURE buffers. Thus, there is no need to check or set the buffer's
'type' field since it must already be set to VIDEO_CAPTURE.
There also appeared to be a copy and paste error in
vidioc_try_fmt_vid_cap() that would set f->fmt.pix.sizeimage to zero.
Note that the s_fmt_vid_cap method doesn't appear to actually do anything.
Whatever parameters were requested are just silently ignored. Was this
intentional? Who knows, as the commit log entry for the driver just says,
"Add generic cx23417 hardware encoder support." There are no docs. A
comment like "this driver totally ignores the v4l2 spec w.r.t.
VIDIOC_S_FMT because ..." would have gone a long way.
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core only allows buffer types for which the corresponding
->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(q|dq|query)bufs() and vidioc_reqbufs().
This driver only defines ->vidioc_try_fmt_vid_cap() so only VIDEO_CAPTURE
buffers are allowed to be used with cafe_vidioc_reqbufs(),
cafe_vidioc_querybuf(), cafe_vidioc_qbuf(), and cafe_vidioc_dqbuf().
The ->vidioc_(s|g|try|enum)_fmt_vid_cap() methods are only called on
VIDEO_CAPTURE buffers. Thus, there is no need to check or set the buffer's
'type' field since it must already be set to VIDEO_CAPTURE. So the
check in cafe_vidioc_enum_fmt_vid_cap() can be removed.
The 'index' field of v4l2_buffer is unsigned so the checks for it being
less than zero can be removed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core only allows buffer types for which the corresponding
->vidioc_try_fmt_xxx() methods are defined to be used in vidioc_(g|s)_parm,
vidioc_(q|dq|query)buf, and vidioc_reqbufs.
Remove buffer type checking from vino_g_parm(), vino_s_parm(),
vino_reqbufs(), vino_querybuf(), vino_qbuf(), and vino_dqbuf(). This
reduced the indent level of the code so a few lines can be wrapped better.
Also fixed the C++ type comments.
The v4l2-ioctl core also provides structs that have been pre-zeroed for all
fields that driver is supposed to fill in, so remove zeroing code from
vino_enum_fmt_vid_cap(). Also, the format index is unsigned so it's not
necessary to check if it's less than zero.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core only allows buffer types for which the corresponding
->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(q|dq|query)bufs(), vidioc_reqbufs() and now vidioc_(s|g)_parm.
This driver only defines ->vidioc_try_fmt_vid_cap() so only VIDEO_CAPTURE
buffers are allowed to be used with vidioc_g_parm(), vidioc_qbuf(),
vidioc_dqbuf(), and vidioc_reqbufs().
Cc: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core now only allows buffer types for which the corresponding
->vidioc_try_fmt_xxx() methods are defined to be used in vidioc_(g|s)_parm.
This driver only defines ->vidioc_try_fmt_vid_cap() so only VIDEO_CAPTURE
buffers are allowed to be used with vidioc_s_parm() and vidioc_g_parm().
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core checks the buffer type now by only allowing buffer
types for which the corresponding ->vidioc_try_fmt_xxx() methods are
defined.
This driver only defines ->vidioc_try_fmt_vid_cap() so only VIDEO_CAPTURE
buffers are allowed to be used with vidioc_g_parm. Also,
->vidioc_enum_fmt_vid_cap() is only called for VIDEO_CAPTURE buffers.
There is no need to set the buffer type since it must already be the
correct value.
The struct which ->vidioc_querycap() is supposed to fill in is already
zeroed so it's not necessary to call memset on it.
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core only allows buffer types for which the corresponding
->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(q|dq|query)bufs(), vidioc_reqbufs() and now vidioc_(s|g)_parm.
The driver was only allowing VIDEO_CAPTURE buffers for g_parm, but since
the driver defines ->vidioc_try_fmt_vid_overlay() and
->vidioc_try_fmt_vbi_cap() it will now allow VIDEO_OVERLAY and VBI_CAPTURE
buffers as well. This should be fine as the driver only fills in the frame
rate field, which is just as valid for video overlay and vbi capture as it
is for video capture.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-ioctl core now only allows buffer types for which the
corresponding ->vidioc_try_fmt_xxx() methods are defined to be used with
vidioc_(g|s)_parm.
The driver was only allowing VIDEO_CAPTURE buffers for g_parm, but since
the driver defines ->vidioc_try_fmt_vid_overlay() it will now allow
VIDEO_OVERLAY buffers as well. This should be fine as the fields the
driver fills in, readbuffers and frame rate, aren't wrong for VIDEO_OVERLAY
buffers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return EINVAL if VIDIOC_S/G_PARM is called for a buffer type that the
driver doesn't define a ->vidioc_try_fmt_XXX() method for. Several other
ioctls, like QUERYBUF, QBUF, and DQBUF, etc. do this too. It saves each
driver from having to check if the buffer type is one that it supports.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers that use this device have been converted to v4l2_subdev, so
there is no more need to support autoprobing on kernels >= 2.6.22.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This card has the saa6752hs on 7-bit address 0x21 instead of 0x20. Add
support in the card definition struct to select which address to use and
update the definitions accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that don't set "config" directly in the set_type function will
end up with an invalid configuration value. Check that the value is sane,
otherwise initialize to 0.
Thanks to James Edward Geiger & Steven Toth for reporting this bug.
Cc: Steven Toth <stoth@linuxtv.org>
Cc: James Edward Geiger <james.e.geiger@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the debug output from stb6100_cfg.h as it is flooding
the syslog with tuning data during normal operation.
Signed-off-by: Artem Makhutov <artem@makhutov.org>
Acked-by: Manu Abraham <abraham.manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Makes the next capturing starting faster and more reliable.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the card is ejected on some systems you get a spew of messages as other
shared IRQ devices interrupt between the card eject and the card IRQ
disable.
We don't need to spew them all out
Closes#7472
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ioremap one was reported in October 2007 (Bug 9146), the kmalloc one
was blindingly obvious while looking at the ioremap one
The bug suggests some other configuration for lots of I/O memory (32MB per
device is ioremapped) but I'll leave that to the real maintainers
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Shared memory mappings on nommu machines require a get_unmapped_area
file operation that suggests an address for the mapping. This patch
adds a way for v4l2 drivers to provide this callback.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix printk format warning:
drivers/media/video/zoran/zoran_driver.c:345: warning: format '%lx'
expects type 'long unsigned int', but argument 5 has type 'phys_addr_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Separate tuning table for DVB-C solves tuning problem at 388MHz
TechnoTrend C-1501 DVB-C card does not lock on 388MHz. I assume that
existing frequency table is valid for DVB-T.
This is suggested by the name of the table: tda827xa_dvbt.
Added a table for DVB-C with the name tda827xa_dvbc.
Added runtime selection of the DVB-C table when the tuner is type
FE_QAM.
This should leave the behaviour of this driver with with DVB_T tuners
unchanged. This modification is in file tda827x.c
The tda827x.c gives the following warning message when debug=1:
tda827x: tda827x_config not defined, cannot set LNA gain!
Solved this by adding a tda827x_config struct in budget-ci.c.
Signed-off-by: Klaas de Waal <klaas.de.waal@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
unlock io_mutex in hdpvr_stop_streaming hdpvr_disconnect to allow the
streaming worker to stop before we flush the workqueue.
do not return to user space with mutex held in vidioc_encoder_cmd with
an unknown encoder command.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
simplifies check for available data with hdpvr_get_next_buffer
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/ce6230.c: In function ‘ce6230_i2c_xfer’:
drivers/media/dvb/dvb-usb/ce6230.c:107: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/usbvideo/vicam.c: In function ‘vicam_open’:
drivers/media/video/usbvideo/vicam.c:194: warning: ‘fw’ may be used uninitialized in this function
drivers/media/video/dabusb.c: In function ‘dabusb_probe’:
drivers/media/video/dabusb.c:337: warning: ‘fw’ may be used uninitialized in this function
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prefer the gspca sonixj driver for the Philips SPC600NC webcam instead of
the sn9c102 driver. As we've got userreports that it works with the gspca
driver, whereas it fails with the sn9c102 driver, see:
https://bugzilla.redhat.com/show_bug.cgi?id=477111
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code in the new sq905c.c is based upon the structure of the code in
gspca/sq905.c, and upon the code in libgphoto2/camlibs/digigr8, which supports
the same set of cameras in stillcam mode. I am a co-author of gspca/sq905.c and
I am the sole author of libgphoto2/camlibs/digigr8, which is licensed under the
LGPL. I hereby give myself permission to use my own code from libgphoto2 in
gspca/sq905c.c.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Forgot to include the tda9887 component when moving to v4l2-subdev. I
got fooled because its name is "tuner", the same as the tuner module.
Silly me.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove ancient IVTV_IOC_G_CODEC and IVTV_IOC_S_CODEC ioctl functions
from the pvrusb2 driver. These are very very old, were non-standard,
and were only present to keep MythTV happy (their implementation did
nothing except to report success). That was long ago; no recent
versions of MythTV should require this anymore.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change removes the old i2c module controlling layer from the
pvrusb2 driver. This is code that first had appeared in the driver
back in December 2005. It's history. Now we use v4l2-subdev. Please
note also that with this change, the driver will no longer be usable
in kernels older that 2.6.22.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-subdev infrastructure requires that an initialization call
must be issued to all attached sub-devices before normal operation can
start. This change satisfies that requirement.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a pvrusb2 driver instance first initializes, we need to be sure
to send out a complete state update for everything to all attached
modules. The old i2c layer did this by keeping a separate mask of
"stale" bits for each attached module - and setting that mask to all
stale when that module attaches. But the new sub-device adaptation
I've implemented here no longer has per-module stale bits. So instead
there's now a global "force dirty" bit that is set upon instance
initialization, before the sub-devices are attached. After the first
update, this bit is cleared, allowing for normal update-on-dirty
behavior. In this manner, we ensure that all sub-devices have been
properly synchronized at initialization.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner sub-device isn't going to work very well unless we tell it
the correct tuner type to use...
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sub-device update mechanism relies on various "dirty" bits in the
driver in order to know what pieces of state need to be propagated out
to the various sub-devices. But that won't work if the dirty bits are
cleared before the update gets a chance to run. This change ensures
that the update takes place before the dirty bits are cleared.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A sub-device won't successfully attach to our I2C adapter if its class
isn't set to zero. Right the class is still set to
I2C_CLASS_TV_ANALOG in order to allow the old mechanism to still
work. This change temporarily sets the class to zero during the
interval when the sub-device attaches. This code will get removed
when the old i2c layer is finally removed from the driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pvrusb2 driver had previously been using i2c module specific calls
to set the sample rate (a long long time ago this was needed). These
days it is safe to use a broadcast so let's just broadcast this when
communicating audio sample rate to sub-devices.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lay down a foundation whereby it becomes possible to send customized
updates to specific sub-devices. (This becomes useful for routing
configuration, which is a very sub-device specific operation.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pvrusb2 driver has a function that reports internal state. It can
be accessed from either the debug interface or as the result of a v4l
log status request. This change adds information listing sub-devices
to the report.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Other code may need to treat the video decoder sub-device in a special
manner, so this change implements code to recognize when such a
sub-device is connected to the driver, does any special processing for
it, and notes who the device is for future reference.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is another step in the v42l-subdev assimilation. This implements
various call-outs to sub-devices based on state changes within the
pvrusb2 driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement status fetching operations in terms of calling out to
sub-device(s).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement tie-in for v4l2 debug register access such that the
appropriate attached sub-device is handled.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trigger a broadcast to attached sub-devices when a logging request is made.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These changes set up the spot where we'll check for and set general
updates to any attached sub-devices.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tie up loose ends with v4l2-subdev setup. Set attached module's group
ID to match our internal ID, emit a few useful messages when
sub-devices are dealt with, implement better error legs, and fix an
error in the old i2c layer (caused by changes related to the
v4l2-subdev work here).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to keep a sub-device from promiscuously attaching to the
pvrusb2 driver, the i2c adapter's class must be cleared. This change
clears that class by default.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This implements a temporary mechanism to "untrack" an i2c module from
the old i2c layer. The v4l2-subdev related code in the driver will
use this to remove a sub-device from the old i2c layer. In the end,
once the old i2c layer is removed, this will also eventually go away.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set up new mechanism for declaring and loading appropriate sub-devices
when driver initializes. This is another part of the v4l2-subdev
adoption.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This introduces some additional isolation in the pvrusb2 from the old
i2c layer, a step along the way to separate the driver from that layer
and to make it easier to introduce the common v4l2-subdev framework as
the eventual replacement.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Define a v4l2_device instance in the pvrusb2 driver and initialize /
tear it down appropriately. This is a step in the v4l2-subdev
adoption effort.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the first step in the effort to move the pvrusb2 driver over
to using the v4l2-subdev framework. This commit involves mainly
splitting apart pvrusb2-i2c-core - part of it is the driver's I2C
adapter driver and the rest is the old i2c module handling logic. The
i2c module handling junk is moved out to pvrusb2-i2c-track and various
header references are correspondingly updated. Yes, this patch has a
huge pile of checkpatch complaints, but I'm NOT going to fix any of
it. Why? First, I'm moving a large chunk of existing code and I'm
not going to spend time adjusting it to match someone's idea of coding
style. Second, in the end I expect all that moved code to go away by
the time the rework is done so wasting time on it now to adhere to the
standard is in the end a large waste of time.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing URB_NO_TRANSFER_DMA_MAP flag, since the use of consistent memory
is not permitted for DMA on the ARM platform.
Thanks to Paul Thomas <pthomas8589@gmail.com> for providing sample ARM
hardware that was experiencing the oops (tested on the at91rm9200 based
LinuxStamp).
Thanks to David Brownell <david-b@pacbell.net> for providing insight into the
ARM memory architecture.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing URB_NO_TRANSFER_DMA_MAP flag, since the use of consistent memory
is not permitted for DMA on the ARM platform.
Thanks to Paul Thomas <pthomas8589@gmail.com> for providing sample ARM
hardware that was experiencing the oops (tested on the at91rm9200 based
LinuxStamp).
Thanks to David Brownell <david-b@pacbell.net> for providing insight into the
ARM memory architecture.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing URB_NO_TRANSFER_DMA_MAP flag, since the use of consistent memory
is not permitted for DMA on the ARM platform.
Thanks to Paul Thomas <pthomas8589@gmail.com> for providing sample ARM hardware
that was experiencing the oops (tested on the at91rm9200 based LinuxStamp).
Thanks to David Brownell <david-b@pacbell.net> for providing insight into the
ARM memory architecture.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The HVR-900 did not have a remote control defined, so it would not work. Add
the line for both versions of the product.
Thanks to Jens-Michael Hoffmann (#linuxtv user "jmho") for pointing out the
issue and testing the patch.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several Kconfig items using CUSTOMIZE. Yet, most use the English
writing CUSTOMISE. This generates lots of trouble, because people sometimes type
the Kbuild item different.
Let's standardise every occurrence using the same syntax.
The changes were generated by this small shell script:
for i in `find linux -type f`; do sed s,CUSTOMIZE,CUSTOMISE,g $i >/tmp/a && mv /tmp/a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for ProVideo PV-183 to bttv
This patch adds support for the ProVideo PV-183 card to the bttv
device driver. The PV-183 is a PCI card with 8 BT878 devices plus a Hint
Corp HiNT HB4 PCI-PCI Bridge. Each BT878 has two composite input channels
available. There are no tuners on this card.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to lack of hardware this conversion to v4l2_device/v4l2_subdev is
untested. If all goes well I should be able to test it in about a month,
but just in case I can't manage that it should be made clear in the code
that this isn't tested.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using VIDIOC_DBG_S/G_REGISTER is the standard way of reading/writing register
for advanced debugging under v4l2. In addition, using this means that the
cafe_ccic driver doesn't need to have knowledge about the used sensor: the
debug ioctl can be passed on to the sensor if it isn't for the host.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-i2c-drv-legacy.h and ov7670_command are no longer needed after the
cafe driver is converted to use v4l2_subdev.
Rather than using a large ov7670_control array, just call the handlers
via a simple switch and use v4l2_ctrl_query_fill() to handle queryctrl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert this driver to v4l2_device and removed the unnecessary cafe_dev_list.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These ops are used by the ov7670 driver, so these need to be added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Randy Dunlap <randy.dunlap@oracle.com>:
ERROR: "dvb_dummy_fe_ofdm_attach" [drivers/media/video/cx231xx/cx231xx-dvb.ko] undefined!
This happens since cx231xx DVB part still misses the frontend modules.
So, the dummy frontend were used for development. The proper fix is to
implement the DVB modules there, as they will be required.
While this won't happen, lets allow the compilation with or without the
dummy FE testing module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
au8522 is now dependent of V4L2, as reported by Randy Dunlap
<randy.dunlap@oracle.com>:
au8522_decoder.c:(.text+0x199898): undefined reference to `v4l2_ctrl_query_fill'
au8522_decoder.c:(.text+0x1998b3): undefined reference to `v4l2_ctrl_query_fill'
au8522_decoder.c:(.text+0x199944): undefined reference to `v4l2_device_unregister_subdev'
au8522_decoder.c:(.text+0x19997c): undefined reference to `v4l2_chip_ident_i2c_client'
au8522_decoder.c:(.text+0x199f1e): undefined reference to `v4l2_i2c_subdev_init'
Cc: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Kyle McMartin and Randy Dunlap:
drivers/media/video/au0828/au0828-video.c:1438: error: 'const struct v4l2_subdev_core_ops' has no member named 'g_register'
drivers/media/video/au0828/au0828-video.c:1453: error: 'const struct v4l2_subdev_core_ops' has no member named 's_register'
This patch properly implements those two API ioctls only when debug is
enabled.
Cc: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
normal_i2c and I2C_CLIENT_INSMOD are only necessary for kernels < 2.6.22.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-common doesn't have to be a module for it to call request_module().
Just remove that test.
Thanks-to: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The encoder commands ioctls are available in v4l2_ioctl_ops. Use them
and get rid of the custom ioctl handler and use video_ioctl2.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device encodes component video up to 1080i to a MPEG-TS stream with
H.264 video and stereo AAC audio. Newer firmwares accept also AC3
(up to 5.1) audio over optical SPDIF without reencoding.
Firmware upgrade is unimplemeted but rather unimportant since
the firmware sits on a flash chip.
The I2C adapter to drive the integrated infrared receiver/sender is
currently disabled due to a conflict with cx18-based devices.
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed some unnecessary memcpy()'s by reworking the compress_*_vbi_buf()
functions.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sliced VBI payloads that cx18 and ivtv would insert in the MPEG stream
did not have consistent endianess for the linemasks in the payload (a big
endian platform would write them out big endian). This change ensures the
linemasks are always stored as little-endian in the MPEG stream to ensure
cross platform consistency in parsing the generated MPEG stream.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per Hans Verkuil <hverkuil@xs4all.nl> instruction, remove the au8522_command
and replace v4l2-i2c-drv-legacy.h with v4l2-i2c-drv.h
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for reviewing the au8522 analog
support.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per Hans Verkuil <hverkuil@xs4all.nl> instruction, remove the deprecated
attach_inform/detach_inform routines, and convert over the i2c calls to
subdev calls.
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for providing feedback on the
au0828 analog support.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VBI support or the au0828 has the framework written but it does not yet
work. Rename the macro per Mauro's request.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take a pass over all of the au0828/au8522 files and cleanup all the codingstyle
issues. This patch does not make *any* functional change to the code.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the sake of completeness, include the "undefined" input type enumeration,
even though there is no path that can actually call it.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing this out.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were some braces left behind from when there was more code in the block.
Remove it.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing this out.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The userland callers are responsible for clearing the output buffers, so
remove the unneeded memset calls.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing this out.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure newly created v4l2 devices have a unique name, modeling the logic
after the cx18 driver.
Thanks to Andy Walls <awalls@radix.net> for pointing out the issue.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert over to using the new subdev framework for the au0828 bridge. This
includes using the new i2c probing mechanism.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the analog initialization failed to create the video device, we never
actually add the entry to the au0828_devlist. Therefore a panic occurs when
unregistering the analog subsystem.
Make it so we only remove the entry from the list if we added it to the list
in the first place.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is not valid to look for dev->board.input == NULL to detect an undefined
analog configuration section, since it is a member of the struct and not a
pointer (hence it will *always* be non-NULL). Do the check based on whether
the first input is actually a valid input type instead.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing sample hardware
of various configurations to test with.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the setup of the analog isoc handler into au0828-video.c, so it does not
occur if there is not an .input section defined for the board. Also fixes a
case where if there is an input section but the board does not actually have
analog support, the digital support will continue to work as expected.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing sample hardware
of various configurations to test with.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the g_chip_ident call work for the au0828/au8522. Discovered when testing
with the v4l2_compliance tool
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: fix merge conflict, due to a path change for analog demod]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it a little easier to read the debug messages for register read/write
operations
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a bug where enumerating the i2c for devices would result in false
positives. The root of the issue was the scanning was using SMBUS_QUICK
messages, which are zero length write requests (which our i2c adapter
implementation didn't handle). Because we never strobed any bytes onto the
bus, the status register would still contain the value from the previous
request.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the VBI support is not yet working for the au0828, don't advertise the
capability or create the /dev/vbi device.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't now how to make any variant of NTSC work other than NTSC-M, so don't
advertise that we support the other variants.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prior to now, we never relied on the Hauppauge tveeprom to identify which
tuner is associated with the board. Now that the HVR-950q determines what
the tuner is based on the eeprom, set the tuner ID appropriately.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing information on
the tveeprom organization.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the way boards are managed so that we can change the board description
based on the Hauppauge eeprom (modeled after cx88-cards.c).
Also, make sure that we don't load the analog stack if there are no analog
inputs defined in the board profile.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for providing information on
the various ways different Hauppauge boards can be configured.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Access using the hybrid state framework requires the list to be protected by
a mutex.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for reporting this during a
code review.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the analog parameters to the device profile for the HVR-850
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is an issue related to the i2c clock for addressing the xc5000. The
au0828 chip does not support clock stretching, which the xc5000 makes use of.
This results in cases where we silently get back garbage in i2c read
operations. To work around this issue until we slow down the i2c clock when
talking with that specific device.
This was not an issue before we had analog support because we never needed to
enumerate the i2c bus, and digital tuning never actually needed to perform
read operations against the xc5000.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the analog functionality found in the au0828 bridge
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab@redhat.com: fix compilation by adding linux/version.h]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the analog functionality in the au8522 analog/digital
demodulator
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
[mchehab: renamed drivers/media/video/au8522_decoder.c as drivers/media/dvb/frontends/au8522_decoder.c to avoid breaking bisect]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make use of the hybrid tuner framework so the analog and digital parts of the
au8522 demodulator can make use of the same shared state.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the au8522 is idle, put the chip into a low power mode (reduces power
consumption from 450ma to 346ma)
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the i2c messages to read and write registers, the two high order bits
of the first byte dictates whether it is a read or a write operation.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the au8522 state structure, as well as exposing functions needed by the
analog side of the demodulator into a common header file.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the au8522.c file to au8522_dig.c so that more source files can be
added to the driver while preserving the original name of au8522.ko
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc5000 driver has a bug where the IF is always set to whatever the first
caller to dvb_attach() provides. This fails when the device requires an IF
other than 5380 and the analog driver is loaded first through tuner-core
(which always supplies the hard-coded value of 5380).
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It appears TS discontinuity about one per 10 hrs if CAM used.
Patch to fix it.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CI high address lines disappears due to wrong data type used.
Patch to fix it.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_dev field of video_device wasn't initialized. The parent field
is derived from v4l2_dev, so that doesn't need to be set anymore.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Call v4l2_device_disconnect when the parent of a hotpluggable device
disconnects. This ensures that you do not have a pointer to a device that
is no longer present.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG quality of the images (quantization tables) is now settable by the
VIDIOC_S_JPEGCOMP ioctl.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- The video device is not allocated when mt9t031_init() is called, don't use
it in debug printk.
- The clock polarity is inverted in mt9t031_set_bus_param(), use the correct
one.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the phytec specific setting of the bus width
and switches to the more generic query_bus_param/set_bus_param
hooks
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the phytec specific setting of the bus width
and switches to the more generic query_bus_param/set_bus_param
hooks
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure videobuf_waiton() is used before freeing a buffer.
Without this fix we may return the buffer to the allocator
before the bus mastering operation is finished.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Tested-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera doesn't set up any image format without an explicit
S_FMT. According to the API this should be supported, for example,
capture-example.c from v4l2-apps by default doesn't issue an S_FMT. This
patch moves negotiating of available host-camera format translations to
probe() time, and restores the state from the last close() on the next
open(). This is needed for some drivers, which power down or reset
hardware after the last user closes the interface. This patch also has a
nice side-effect of avoiding multiple allocation anf freeing of format
translation tables.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the case, that we have to capture with a default format, i.e., when the
user doesn't call S_FMT, we have to use the field value according to the
default, configured at open() time.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently soc-camera doesn't set up any image format without an explicit S_FMT.
It seems this should be supported, since, for example, capture-example.c from
v4l2-apps by default doesn't issue an S_FMT. This patch configures a default
image format on open().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As host and camera drivers become more complex, differences between S_FMT and
S_CROP functionality grow, this patch separates them.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bt819 needs the parent driver to drive a GPIO pin low and high in order to
reset its fifo. Use the new notify callback for this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Normally the parent device of v4l2_device is used as the video device
node's parent. But if it was not set, then use the parent field in the
video_device struct.
This is needed in the cx88 driver, which has one core v4l2_device but
creates multiple pci devices (one each for raw and mpeg video).
So you cannot associate the core v4l2_device with a particular PCI device,
but you can do that for each video_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new support for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI board broke the
existing boards. Interrupts for the netup part were enabled and handled
without testing whether the current board actually had a netup -> instant
and fatal crash.
I've added tests to do this only for the CX23885_BOARD_NETUP_DUAL_DVBS2_CI
board.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug where all frame headers were being discarded, instead of being part of the
stream output, on MR97310A cameras.
The frame headers contain information which may be useful in processing
the video output and therefore should be kept and not discarded.
A corresponding patch to the decompression algorithm in
libv4lconvert/mr97310a.c corrects the change in frame offset.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setting state->frontend.demodulator_priv to NULL in the event of
a kzalloc error will result in an OOPS. Just remove that line.
Thanks to Matthias Schwarzott for pointing this out.
Cc: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the i2c sub-device cannot be found, then we must unregister the i2c_client.
Otherwise this will prevent a possible probe for a different device on that same
address.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll start off with MODULE_VERSION("0.1")
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
small whitespace cleanup - space missing after the *
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vfl_type field is set by the core, so anything you fill in here will
be overwritten. And it will be set to a VFL_TYPE_ value, not a VID_TYPE_
value which is an obsolete V4L1 type.
Since these V4L1 types have been made unavailable for V4L2 drivers, this
driver stopped compiling.
In this case the fix is just removing this assignment.
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This include isn't needed and so can be removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for Terratec Cinergy HT PCI MKII with card id 79.
Its more or less a copy of Pinnacle Hybrid PCTV.
Thanks to k1ngf1sher on forum.ubuntuusers.de for the idea to copy that card.
Signed-off-by: Stephan Wienczny <stephan@wienczny.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Print a message in case the new software IRQ watchdog detects a problem.
I choose the info message category, this can be changed if not appropriate.
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videodev module is missing the char-major-81-* alias that would
cause it to be auto-loaded when a device of that type is opened. This
patch adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Call pwc_construct before trying to talk to device to obtain vc interface so
that LED and power setup works the first time the video device is opened.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When unloading the cx8800 driver I sometimes get a general protection
fault. Analysis revealed a race in cx88_ir_stop(). It can be solved by
using a delayed work instead of a timer for infrared input polling.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The removal of the timer which polls the infrared input is racy.
Replacing the timer with a delayed work solves the problem.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The removal of the timer which polls the infrared input is racy.
Replacing the timer with a delayed work solves the problem.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The removal of the timer which polls the infrared input is racy.
Replacing the timer with a delayed work solves the problem.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It reduces the size of the driver over all, and the function names in
strings need to be manually kept up to date while __func__ doesn't.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many functions had a struct file pointer argument, but all they wants is
the struct zoran_fh pointer from the file's private data. Since every
caller of those functions already has the zoran_fh, just pass the that
instead. This saves a dereference in each function change.
While I'm at it, change the code formatting of affected functions to be
kernel standard style.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kmalloc() can fail for large video buffers. By default the kernel
complains loudly about allocation failures, but we don't want to
frighten the user, so ask kmalloc() to keep quiet on such failures.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lock_norm module parameter doesn't look terribly useful. If you
don't want to change the norm, just don't change it. As a matter of
fact, no other v4l driver has such a parameter.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The zoran driver had two kinds of buffer descriptors, one for jpg buffers
and one for raw buffers. They were mostly the same with only a couple
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
replace occurances of "HVR1150" with "HVR1120" - this was a typo.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are no drivers left that call msp3400 with V4L1 commands. Remove it
from this driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code to optimize the usercopy only checked the ioctl NR field. However,
this code is also called for non-V4L2 ioctls (either private or ioctls from
linux/dvb/audio.h and linux/dvb/video.h for decoder drivers like ivtv).
If such an ioctl has the same NR as a V4L2 ioctl, then disaster strikes.
Modified the code to check on the full command ID.
Thanks to Martin Dauskardt for tracing the ivtv breakage to this particular
change.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver isn't used in any legacy mode, so no need for v4l2-i2c-drv-legacy.h.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As announced VIDIOC_G_CHIP_IDENT_OLD is now removed for 2.6.30.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
changeset 04934e44e3784a1b969582e2d59afcec278470c6 removed the last implementation
that were still using the V4L1 obsoleted header.
Now, video_decoder.h is not used anymore by any driver.
Let's remove it and all references for it in Kernel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was never any build-time dependency of the dib0700 usb module on the
dib0070 tuner module. Now that the build-time dependencies of dib0700 on
dib3000mc, dib7000p and dib7000m have been removed in the previous changesets,
we can enable DVB_FE_CUSTOMISE for these modules under config DVB_USB_DIB0700
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function prototype is defined but the function itself does not exist.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It's much nicer if the log message tells you which io ports are possible,
rather than having to run modinfo or look it up in the source or manual.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tda827x driver supports a feature that the tda18271 driver was lacking
until now. This patch adds support for device-level configuration via the
tuner callback configuration interface.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L1 obsoleted header video_decoder.h is not used anymore by any driver. Only
a name decoding function at v4l2-ioctl still implements it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
