RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil_addba_rx_request allocates the rx reorder buffer regardless
of use_rx_hw_reordering settings.
Fix this by checking wil->use_rx_hw_reordering before allocating
the reorder buffer.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil6210 supports channels 1-3 of the 60GHz band.
New FW added support for channel 4. Add support for channel 4 also in
wil6210 driver.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset file is not used and may cause race conditions
with operational driver if used.
Signed-off-by: Karthick Gopalasubramanian <kargop@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx99 is typically configured via a monitor mode interface, which does
not get added to the driver as a vif. Since the code currently expects
a configured virtual interface for tx99, enabling tx99 via debugfs fails.
Since the vif is not needed anyway, remove all checks for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@codeaurora.org: s/CPTCFG/CONFIG/]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Array firstep_table is being assigned but is never used
hence it is redundant and can be removed.
Cleans up clang warning:
warning: 'firstep_table' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove extra parentheses to fix the clang warning of extraneous
parentheses.
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 has the MAC_PCU_ADDR1 configured properly
and hence it will not send spurious ack frames
during boot up.
Hence the reset_rx_filter workaround is not needed
for WCN3990. Add a hw_param to indicate if hardware rx
filter reset is needed and skip the reset_rx_filter for
WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When continuously running wifi up/down sequence, the napi poll
can be scheduled after the CE buffers being freed by ath10k_pci_flush
Steps:
In a certain condition, during wifi down below scenario might occur.
ath10k_stop->ath10k_hif_stop->napi_schedule->ath10k_pci_flush->napi_poll(napi_synchronize).
In the above scenario, CE buffer entries will be freed up and become NULL in
ath10k_pci_flush. And the napi_poll has been invoked after the flush process
and it will try to get the skb from the CE buffer entry and perform some action on that.
Since the CE buffer already cleaned by pci flush this action will create NULL
pointer dereference and trigger below kernel panic.
Unable to handle kernel NULL pointer dereference at virtual address 0000005c
PC is at ath10k_pci_htt_rx_cb+0x64/0x3ec [ath10k_pci]
ath10k_pci_htt_rx_cb [ath10k_pci]
ath10k_ce_per_engine_service+0x74/0xc4 [ath10k_pci]
ath10k_ce_per_engine_service [ath10k_pci]
ath10k_ce_per_engine_service_any+0x74/0x80 [ath10k_pci]
ath10k_ce_per_engine_service_any [ath10k_pci]
ath10k_pci_napi_poll+0x48/0xec [ath10k_pci]
ath10k_pci_napi_poll [ath10k_pci]
net_rx_action+0xac/0x160
net_rx_action
__do_softirq+0xdc/0x208
__do_softirq
irq_exit+0x84/0xe0
irq_exit
__handle_domain_irq+0x80/0xa0
__handle_domain_irq
gic_handle_irq+0x38/0x5c
gic_handle_irq
__irq_usr+0x44/0x60
Tested on QCA4019 and firmware version 10.4.3.2.1.1-00010
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HW requires Rx buffers to be 4 bytes aligned. Modify the driver to
meet this requirement.
Enable OFU rdy valid bug fix, to prevent hang in oful34_rx while
there is back-pressure from host during RX.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver doesn't support secured boot flow, hence
prevent FW download in case HW is configured for such a flow.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently wil6210 ignores the channel field in the
cfg80211_mgmt_tx_params struct for wil_cfg80211_ops mgmt_tx operation
and sends all management frames on the serving channel.
Add support for off-channel transmission of management frames
(WIPHY_FLAG_OFFCHAN_TX) in AP mode. This is useful in enterprise APs
for sending custom probe request frames.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Single MSI is the current default configuration.
With multiple MSI interrupts configuration, Tx/Rx processing could
run in parallel on different CPU cores and allow better balance
between the cores.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device can be different from the default name.
In such a case use a corresponding board file name.
If such a board file is not present FW download procedure will fail.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.
Increase the timeout to support these scenarios.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW can support BACK window size 64 for performance improvements.
A new FW capability is added for notifying the host on the increased
max BACK win size support.
Defining WIL_MAX_AGG_WSIZE_64 and WIL_MAX_AMPDU_SIZE_128 to be used
in this case.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Scan is allowed only on client interfaces (STA/P2P).
Allow scan on AP interface so that the AP can discover rouge
or unauthorized neighbor APs.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can request FW to report link statistics using
WMI_LINK_STATS_CMDID.
FW will report statistics with WMI_LINK_STATS_EVENTID.
Two categories of statistics defined: basic and global.
New "link_stats" debugfs is used for requesting basic statistics
report (write) and for reading the basic statistics (read).
"link_stats_global" debugfs is used for requesting and reading the
global statistics.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With some tool chains compilation fails due to type
mismatch of the arguments passed to min().
Use min_t() to solve these compilation errors.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extend MSI support to 3-MSI in order to load balance the tx\rx
interrupts between different cores.
use_msi module parameter has changed to n_msi. Usage:
- Set n_msi to 0 for using INTx
- Set n_msi to 1 for using single MSI
- Set n_msi to 3 for using 3-MSI
In 3-MSI configuration MSI 0 is used for TX interrupts, MSI 1
is used for RX interrupts and MSI 2 is used for MISC interrupts.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW file name for Talyn device is different from the default name.
This patch searches for Talyn specific FW file name and fallback
to the default FW file in case it is not present.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the driver sets CHECKSUM_UNNECESSARY only in case the HW
doesn't report checksum error.
As ip_summed value is not initialized it is not clear what
the driver will report to the network stack in case of HW checksum
error or in case HW doesn't calculate checksum.
Initialize ip_summed to CHECKSUM_NONE to guarantee checksum
calculation by the network stack in the above cases.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collect statistics of TX latency. The latency is measured from the time
the HW gets aware of new SKB to transmit until the HW indicates tx
complete for this SKB.
The statistics are shown via new "tx_latency" debugfs.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to recent change in FW, driver will be notified of corrupted Rx
packets (e.g. MIC error).
Drop such packets before they are delivered to network stack.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Store the last received multicast sequence number (SN) part of the TID
info. Drop Rx multicast packets with retry bit set which their SN
is equal to the last received.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The flag needs to be cleared for the last packet in the list, not the
first one. Fixes some issues with multicast packet loss for powersave
clients connected to an ath9k AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lower limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ensure that a buffer gets tracked as part of the block-ack window as
soon as it's dequeued from the tid for the first time. Ensure that
double calls to ath_tx_addto_baw (e.g. on retransmission) don't cause
any issues.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes missed indications of end of U-APSD service period to mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The checks already prevents periodic cal from being started while noise
floor calibration runs. It is missing checks for the other way around.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9002 code and the QCA AR9003+ reference code do the same.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath6kl_bmi_init() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The QCA4019 hw1.0 firmware 10.4-3.2.1-00050 and 10.4-3.5.3-00053 (and most
likely all other) seem to ignore the WMI_CHAN_FLAG_DFS flag during the
scan. This results in transmission (probe requests) on channels which are
not "available" for transmissions.
Since the firmware is closed source and nothing can be done from our side
to fix the problem in it, the driver has to work around this problem. The
WMI_CHAN_FLAG_PASSIVE seems to be interpreted by the firmware to not
scan actively on a channel unless an AP was detected on it. Simple probe
requests will then be transmitted by the STA on the channel.
ath10k must therefore also use this flag when it queues a radar channel for
scanning. This should reduce the chance of an active scan when the channel
might be "unusable" for transmissions.
Fixes: e8a50f8ba4 ("ath10k: introduce DFS implementation")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These were recently introduced and found by checkpatch:
drivers/net/wireless/ath/ath10k/mac.c:6118: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6121: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6124: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Debugfs support to do hardware warm reset with WMI command
WMI_PDEV_PARAM_PDEV_RESET for 10.4 and 10.2.4(if wmi
service is enabled in the firmware for backward compatibility).
This change is purely for debugging purpose when hardware hangs/mutes.
This hardware reset won't affect the connectivity but there will be small
pause in data traffic. Here we are doing BB/MAC level reset and hence
whenever the BB/MAC watchdog is triggered, it does a hardware_chip_reset.
So the target will be in the active state.
Below command used to warm reset the hardware.
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/warm_hw_reset
Tested in QCA988X with firmware ver 10.2.4.70.45
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is only code refactoring as all call sites of
ath10k_htt_tx_alloc_msdu_id() take the same lock it can be moved into the
id_get function and the assertion dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variables netlen, orig_buf, orig_len, dropped and stats are assigned values
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'netlen' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_buf' set but not used [-Wunused-but-set-variable]
warning: variable 'orig_len' set but not used [-Wunused-but-set-variable]
warning: variable 'dropped' set but not used [-Wunused-but-set-variable]
warning: variable 'stats' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
