This patch is an attempt to limit HDMI 2.0 SCDC setup when :
- the SoC embeds an HDMI 1.4 only controller
- the EDID supports SCDC but not scrambling
- the EDID supports SCDC scrambling but not for low TMDS bit rates,
while only supporting low TMDS bit rates
This to avoid communicating with the SCDC DDC slave uncessary, and
setting the DW-HDMI TMDS Scrambler setup when not supported by the
underlying hardware.
Reported-by: Rob Herring <robh@kernel.org>
Fixes: 264fce6cc2 ("drm/bridge: dw-hdmi: Add SCDC and TMDS Scrambling support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190315095414.28520-1-narmstrong@baylibre.com
DMT monitors does not necessarely report a maximum TMDS clock
in a VSDB EDID extension.
In this case, all modes are wrongly rejected, including
the DRM fallback EDID.
This patch only rejects modes whith clock > max_tmds_clock if
the max_tmds_clock is specified. This will only reject
4:2:0 HDMI2.0 modes, who reports a clock > max_tmds_clock.
Reported-by: Maxime Jourdan <mjourdan@baylibre.com>
Fixes: d7d8fb7046 ("drm/meson: add HDMI div40 TMDS mode")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320081110.1718-1-narmstrong@baylibre.com
meson_drv_unbind() doesn't unregister the IRQ handler, which can lead to
use-after-free if the IRQ fires after unbind:
[ 64.656876] Unable to handle kernel paging request at virtual address ffff000011706dbc
...
[ 64.662001] pc : meson_irq+0x18/0x30 [meson_drm]
I'm assuming that a similar problem could happen on the error path of
bind(), so uninstall the IRQ handler there as well.
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-2-jean-philippe.brucker@arm.com
meson_drv_bind() registers a meson_drm struct as the device's privdata,
but meson_drv_unbind() tries to retrieve a drm_device. This may cause a
segfault on shutdown:
[ 5194.593429] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000197
...
[ 5194.788850] Call trace:
[ 5194.791349] drm_dev_unregister+0x1c/0x118 [drm]
[ 5194.795848] meson_drv_unbind+0x50/0x78 [meson_drm]
Retrieve the right pointer in meson_drv_unbind().
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-1-jean-philippe.brucker@arm.com
Rather than setting debug output flags during early init, its makes
more sense to simply re-define ACPI_DEBUG_DEFAULT specifically for
Linux.
ACPICA commit 60903715711f4b00ca1831779a8a23279a66497d
Link: https://github.com/acpica/acpica/commit/60903715
Fixes: ce5cbf5349 ("ACPI: Set debug output flags independent of ACPICA")
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With this patch multicast packets with a limited number of destinations
(current default: 16) will be split and transmitted by the originator as
individual unicast transmissions.
Wifi broadcasts with their low bitrate are still a costly undertaking.
In a mesh network this cost multiplies with the overall size of the mesh
network. Therefore using multiple unicast transmissions instead of
broadcast flooding is almost always less burdensome for the mesh
network.
The maximum amount of unicast packets can be configured via the newly
introduced multicast_fanout parameter. If this limit is exceeded
distribution will fall back to classic broadcast flooding.
The multicast-to-unicast conversion is performed on the initial
multicast sender node and counts on a final destination node, mesh-wide
basis (and not next hop, neighbor node basis).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Currently incoming ARP Replies, for example via a DHT-PUT message, do
not update the timeout for an already existing DAT entry. These ARP
Replies are dropped instead.
This however defeats the purpose of the DHCPACK snooping, for instance.
Right now, a DAT entry in the DHT will be purged every five minutes,
likely leading to a mesh-wide ARP Request broadcast after this timeout.
Which then recreates the entry. The idea of the DHCPACK snooping is to
be able to update an entry before a timeout happens, to avoid ARP Request
flooding.
This patch fixes this issue by updating a DAT entry on incoming
ARP Replies even if a matching DAT entry already exists. While still
filtering the ARP Reply towards the soft-interface, to avoid duplicate
messages on the client device side.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The send functions in batman-adv are expected to consume the skb when
either the data is queued up for the underlying driver or when some
precondition failed. batadv_dat_send_data didn't do this and instead
created a copy of the skb, modified it and queued the copy up for
transmission. The caller has to take care that the skb is handled correctly
(for example free'd) when batadv_dat_send_data returns.
This unclear behavior already lead to memory leaks in the recent past.
Renaming the function to batadv_dat_forward_data should make it easier to
identify that the data is forwarded but the skb is not actually
send+consumed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux-merge.git repository on git.open-mesh.org is used since 8 years
to send PRs for net.git and net-next.git. It is time to officially specify
list it as SCM tree.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The #batman channel on freenode was created to discuss various B.A.T.M.A.N.
related topics (like batman-adv).
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
While it is acceptable to discuss problems on the mailing list, it is
easier to track bugs in the official bugtracker. Registration is required
to get access to the submission form.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The sysfs files to read and modify the configuration settings were replaced
by the batadv generic netlink family. They are also marked as obsolete in
the ABI documentation. But not all users of this functionality might follow
changes in the Documentation/ABI/obsolete/ folder. They might benefit from
a warning messages about the deprecation of the functionality which they
just tried to access
batman_adv: [Deprecated]: batctl (pid 30381) Use of sysfs file "orig_interval".
Use batadv genl family instead
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The sysfs files are replaced by the batadv generic netlink family. The old
sysfs configuration interface was frowned upon by other kernel developers.
But the files cannot be removed immediately because userspace tools might
still depend on it. Instead schedule for its removal in 2021.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The sysfs files will be marked as deprecated in the near future. They are
already replaced by the batadv generic netlink family. Add an Kconfig
option to disable the sysfs support for users who want to test their tools
or want to safe some space. This setting should currently still be enabled
by default to keep backward compatible with legacy tools.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The sysfs files will be marked as deprecated in the near future. They
are already replaced by the batadv generic netlink family. The
documentation should not advertise its usage anymore and instead
promote the generic netlink family and a userspace tool to access it.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The debugfs files were marked as deprecated by commit 00caf6a2b3
("batman-adv: Mark debugfs functionality as deprecated"). The documentation
should not advertise its usage anymore and instead promote the generic
netlink family and a userspace tool to access it.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All files got a SPDX-License-Identifier with commit 7db7d9f369
("batman-adv: Add SPDX license identifier above copyright header"). All the
required information about the license conditions can be found in
LICENSES/.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The throughput_override sysfs file is not below the meshif but below a
hardif. The kobj has therefore not a pointer which can be used to find the
batadv_priv data. The pointer stored in the hardif object must be used
instead to find the correct meshif private data.
Fixes: 7e6f461efe ("batman-adv: Trigger genl notification on sysfs config change")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When CONFIG_CFG80211 isn't enabled the compiler correcly warns about
'sinfo.pertid' may be unused. It can also happen for other error
conditions that it not warn about.
net/batman-adv/bat_v_elp.c: In function ‘batadv_v_elp_get_throughput.isra.0’:
include/net/cfg80211.h:6370:13: warning: ‘sinfo.pertid’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
kfree(sinfo->pertid);
~~~~~^~~~~~~~
Rework so that we only release '&sinfo' if cfg80211_get_station returns
zero.
Fixes: 7d652669b6 ("batman-adv: release station info tidstats")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_global_free is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: 7683fdc1e8 ("batman-adv: protect the local and the global trans-tables with rcu")
Reported-by: Martin Weinelt <martin@linuxlounge.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_tt_local_remove is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: ef72706a05 ("batman-adv: protect tt_local_entry from concurrent delete events")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_hash_remove is a function which searches the hashtable for an
entry using a needle, a hashtable bucket selection function and a compare
function. It will lock the bucket list and delete an entry when the compare
function matches it with the needle. It returns the pointer to the
hlist_node which matches or NULL when no entry matches the needle.
The batadv_bla_del_claim is not itself protected in anyway to avoid that
any other function is modifying the hashtable between the search for the
entry and the call to batadv_hash_remove. It can therefore happen that the
entry either doesn't exist anymore or an entry was deleted which is not the
same object as the needle. In such an situation, the reference counter (for
the reference stored in the hashtable) must not be reduced for the needle.
Instead the reference counter of the actually removed entry has to be
reduced.
Otherwise the reference counter will underflow and the object might be
freed before all its references were dropped. The kref helpers reported
this problem as:
refcount_t: underflow; use-after-free.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In case devm_kzalloc, the patch returns ENOMEM to avoid potential
NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Now drm/udl driver uses drm_do_get_edid() function to retrieve and
validate all blocks of EDID data. Old approach had insufficient
validation routine and had problems with retrieving of extra blocks
Signed-off-by: Robert Tarasov <tutankhamen@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: Fix spelling mistakes]
Link: https://patchwork.freedesktop.org/patch/msgid/20190314225339.162386-1-tutankhamen@chromium.org
If userspace has open fd(s) when drm_dev_unplug() is run, it will result
in drm_dev_unregister() being called twice. First in drm_dev_unplug() and
then later in drm_release() through the call to drm_put_dev().
Since userspace already holds a ref on drm_device through the drm_minor,
it's not necessary to add extra ref counting based on no open file
handles. Instead just drm_dev_put() unconditionally in drm_dev_unplug().
We now have this:
- Userpace holds a ref on drm_device as long as there's open fd(s)
- The driver holds a ref on drm_device as long as it's bound to the
struct device
When both sides are done with drm_device, it is released.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208140103.28919-2-noralf@tronnes.org
Alexei Starovoitov says:
====================
pull-request: bpf 2019-03-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) libbpf verision fix up from Daniel.
2) fix liveness propagation from Jakub.
3) fix verbose print of refcounted regs from Martin.
4) fix for large map allocations from Martynas.
5) fix use after free in sanitize_ptr_alu from Xu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
First one is fixing version in Makefile and shared object and
second one clarifies bump in version. Thanks!
v1 -> v2:
- Fix up soname, thanks Stanislav!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The current documentation suggests that we would need to bump the
libbpf version on every change. Lets clarify this a bit more and
reflect what we do today in practice, that is, bumping it once per
development cycle.
Fixes: 76d1b894c5 ("libbpf: Document API and ABI conventions")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Even though libbpf's versioning script for the linker (libbpf.map)
is pointing to 0.0.2, the BPF_EXTRAVERSION in the Makefile has
not been updated along with it and is therefore still on 0.0.1.
While fixing up, I also noticed that the generated shared object
versioning information is missing, typical convention is to have
a linker name (libbpf.so), soname (libbpf.so.0) and real name
(libbpf.so.0.0.2) for library management. This is based upon the
LIBBPF_VERSION as well.
The build will then produce the following bpf libraries:
# ll libbpf*
libbpf.a
libbpf.so -> libbpf.so.0.0.2
libbpf.so.0 -> libbpf.so.0.0.2
libbpf.so.0.0.2
# readelf -d libbpf.so.0.0.2 | grep SONAME
0x000000000000000e (SONAME) Library soname: [libbpf.so.0]
And install them accordingly:
# rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld install
Auto-detecting system features:
... libelf: [ on ]
... bpf: [ on ]
CC /tmp/bld/libbpf.o
CC /tmp/bld/bpf.o
CC /tmp/bld/nlattr.o
CC /tmp/bld/btf.o
CC /tmp/bld/libbpf_errno.o
CC /tmp/bld/str_error.o
CC /tmp/bld/netlink.o
CC /tmp/bld/bpf_prog_linfo.o
CC /tmp/bld/libbpf_probes.o
CC /tmp/bld/xsk.o
LD /tmp/bld/libbpf-in.o
LINK /tmp/bld/libbpf.a
LINK /tmp/bld/libbpf.so.0.0.2
LINK /tmp/bld/test_libbpf
INSTALL /tmp/bld/libbpf.a
INSTALL /tmp/bld/libbpf.so.0.0.2
# ll /usr/local/lib64/libbpf.*
/usr/local/lib64/libbpf.a
/usr/local/lib64/libbpf.so -> libbpf.so.0.0.2
/usr/local/lib64/libbpf.so.0 -> libbpf.so.0.0.2
/usr/local/lib64/libbpf.so.0.0.2
Fixes: 1bf4b05810 ("tools: bpftool: add probes for eBPF program types")
Fixes: 1b76c13e4b ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
These are a couple of minor fixes for build issues and sparse warnings.
-----BEGIN PGP SIGNATURE-----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=OOzV
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-5.1-rc2' of git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v5.1-rc2
These are a couple of minor fixes for build issues and sparse warnings.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322131517.825-1-thierry.reding@gmail.com
If the downscaling fails and we end up with a best_depth of 0,
then ignore it.
This actually works around a cascade of failure, but it the
simplest fix for now.
The scaling patch broke the udl driver, as the udl driver doesn't
expose planes at all, so gets the two default 32-bit formats, but
the udl driver then ask for 16bpp fbdev, and the scaling code falls
over.
This fixes the udl driver since the scaled depth support was added.
Fixes: f4bd542bca ("drm/fb-helper: Scale back depth to supported maximum")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190315014621.21816-2-airlied@gmail.com
These three variables are set in one branch and used in another with
the same condition. But on some architectures they still generate
compiler warnings of the kind:
warning: 'inner_trans' may be used uninitialized in this function [-Wmaybe-uninitialized]
Silence these false positives. Use the straightforward approach to
always initialize them, if a bit superfluous.
Fixes: 868d523535 ("bpf: add bpf_skb_adjust_room encap flags")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Jiri Pirko says:
====================
devlink: small spring cleanup
Mostly cosmetics and janitor work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are becoming more dependent on NET_DEVLINK being selected
in configuration. With upcoming compat functions, the behavior would be
wrong in case devlink was not compiled in. So make the drivers select
NET_DEVLINK and rely on the functions being there, not just stubs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spinlock to protect port type and type_dev pointer consistency.
Without that, userspace may see inconsistent type and type_dev
combinations.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v1->v2:
- rebased
Signed-off-by: David S. Miller <davem@davemloft.net>
Port needs to be registered first before the type is set. Warn and
bail-out in case it is not.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the type set of devlink port after it is registered.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other driver, move the port type set after netdev registration
is done. Along with that, clear the type before unregistration.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the port attributes are static and cannot change during the port
lifetime, WARN_ON if some driver calls it after registration. Also, no
need to call notifications as it is noop anyway due to check of
devlink_port->registered there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since attrs are static during the existence of devlink port, set the
before registration of the port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since attrs are static during the existence of devlink port, set the
before registration of the port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__devlink_port_type_set() returns void, it makes no sense to pass it on,
so don't do that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevice is guaranteed to not disappear so we can rely that
devlink_port and devlink won't disappear as well. No need to take
devlink_mutex so don't take it here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink_port_type_eth_set() before devlink_port_register(). Bnxt
instances won't change type during lifetime. This avoids one extra
userspace devlink notification.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the attrs properly so delink has enough info to generate physical
port names.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink functions are in use, so include the related header file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
