Fix recreating the channel VSIs during the reset flow to reconfigure
the Tx rings and the queue context associated with the channel VSI.
Also update the next_base_queue for the VSI while rebuilding the
channel VSIs after a reset.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that i40e_vsi_config_tc() has the pf and hw variable defined, use
them, instead of dereferencing vsi->back. Much easier to read.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver (and the entire netdev layer for that matter) assumes
that TC0 will always be present in our DCB configuration.
Unfortunately, this isn't always the case. Rather than fail to
configure the VSI, let's go ahead and try to make it work, even
though DCB will end up being disabled by the kernel.
If the driver fails to configure DCB, the driver queries what's
valid, then writes that back to the hardware, always forcing TC0.
This fixes a bug where the driver could fail to adhere to ETS BW
allocations if 8 TCs were configured on the switch.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In VFs, there is a known issue which can cause writebacks
to not occur when interrupts are disabled and there are
less than 4 descriptors resulting in TX timeout. Timeout
can also occur due to lost interrupt.
The current implementation for detecting and recovering
from hung queues in the PF is problematic because it actually
actively encourages lost interrupts. By triggering a SW
interrupt, interrupts are forced on. If we are already in
napi_poll and an interrupt fires, napi_poll will not be
rescheduled and the interrupt is effectively lost; thereby
potentially *causing* hung queues.
This patch checks whether packets are being processed between
every watchdog cycle and determine potential hung queue and
fires triggers SW interrupt only for that particular queue.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some weird circumstances with DCB enabled, the firmware can fail to
configure the VSI, leaving us with zero traffic classes. Check for this
state when we configure RSS to avoid a panic.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds new I40E_NVMUPD_GET_AQ_EVENT state to allow
retrieval of AdminQ events as a result of AdminQ commands sent
to firmware.
Add preservation flags support on X722 devices for NVM update
AdminQ function wrapper. Add new parameter and handling to
nvmupdate admin queue function intended to allow nvmupdate tool
to configure the preservation flags in the AdminQ command.
This is required to implement FlatNVM on X722 devices.
Signed-off-by: Pawel Jablonski <pawel.jablonski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the i40e driver from 2.1.14 to 2.3.2.
Bump the i40evf driver from 3.0.1 to 3.2.2
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When filter configuration is not supported, drivers should return
-EOPNOTSUPP so the core can react correctly.
Fixes: 2f4b411a3d ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, such as with bridging, it is possible that the
stack will add a devices own MAC address to its unicast address list.
If, later, the stack deletes this address, then the i40e driver will
receive a request to remove this address.
The driver stores its current MAC address as part of the MAC/VLAN hash
array, since it is convenient and matches exactly how the hardware
expects to be told which traffic to receive.
This causes a problem, since for more devices, the MAC address is stored
separately, and requests to delete a unicast address should not have the
ability to remove the filter for the MAC address.
Fix this by forcing a check on every address sync to ensure we do not
remove the device address.
There is a very narrow possibility of a race between .set_mac and
.set_rx_mode, if we don't change netdev->dev_addr before updating our
internal MAC list in .set_mac. This might be possible if .set_rx_mode is
going to remove MAC "XYZ" from the list, at the same time as .set_mac
changes our dev_addr to MAC "XYZ", we might possibly queue a delete,
then an add in .set_mac, then queue a delete in .set_rx_mode's
dev_uc_sync and then update netdev->dev_addr. We can avoid this by
moving the copy into dev_addr prior to the changes to the MAC filter
list.
A similar race on the other side does not cause problems, as if we're
changing our MAC form A to B, and we race with .set_rx_mode, it could
queue a delete from A, we'd update our address, and allow the delete.
This seems like a race, but in reality we're about to queue a delete of
A anyways, so it would not cause any issues.
A race in the initialization code is unlikely because the netdevice has
not yet been fully initialized and the stack should not be adding or
removing addresses yet.
Note that we don't (yet) need similar code for the VF driver because it
does not make use of __dev_uc_sync and __dev_mc_sync, but instead roles
its own method for handling updates to the MAC/VLAN list, which already
has code to protect against removal of the hardware address.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since UDP based filters are not supported via big buffer cloud
filters, remove UDP support. Also change a few return types to
indicate unsupported vs invalid configuration.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding cloud filters could fail for a number of reasons,
unsupported filter fields for example, which fails during
validation of fields itself. This will not result in admin
command errors and converting the admin queue status to posix
error code using i40e_aq_rc_to_posix would result in incorrect
error values. If the failure was due to AQ error itself,
reporting that correctly is handled in the inner function.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After a reset we rebuild the VSIs which is going to clobber any
promiscuous settings we had before reset. This makes it so that we
restore the promiscuous settings we had before reset.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is safe to remove the upper limit of 64 queues on a channel
VSI. The upper bound is determined by the VSI's num_queue_pairs
and gets validated when the queue mapping info through mqprio
interface is subject to bound checking in the driver.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tc-flower based hardware offloads. tc flower
filter provided by the kernel is configured as driver specific
cloud filter. The patch implements functions and admin queue
commands needed to support cloud filters in the driver and
adds cloud filters to configure these tc-flower filters.
The classification function of the filter is to direct matched
packets to a traffic class. The hardware traffic class is set
based on the the classid reserved in the range :ffe0 - :ffef.
Match Dst MAC and route to TC0:
prio 1 flower dst_mac 3c:fd:fe:a0:d6:70 skip_sw\
hw_tc 1
Match Dst IPv4,Dst Port and route to TC1:
prio 2 flower dst_ip 192.168.3.5/32\
ip_proto udp dst_port 25 skip_sw\
hw_tc 2
Match Dst IPv6,Dst Port and route to TC1:
prio 3 flower dst_ip fe8::200:1\
ip_proto udp dst_port 66 skip_sw\
hw_tc 2
Delete tc flower filter:
Example:
Flow Director Sideband is disabled while configuring cloud filters
via tc-flower and until any cloud filter exists.
Unsupported matches when cloud filters are added using enhanced
big buffer cloud filter mode of underlying switch include:
1. source port and source IP
2. Combined MAC address and IP fields.
3. Not specifying L4 port
These filter matches can however be used to redirect traffic to
the main VSI (tc 0) which does not require the enhanced big buffer
cloud filter support.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jingjing Wu <jingjing.wu@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce the cloud filter data structure and cleanup of cloud
filters associated with the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add definitions for L4 filters and switch modes based on cloud filters
modes and extend the set switch config command to include the
additional cloud filter mode.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add mapping of TCs with the seids of the channel VSIs. TC0
will be mapped to the main VSI seid and all other TCs are
mapped to the seid of the corresponding channel VSI.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whether or not there are vectors_left, we only need to redistribute
our vectors if we didn't get as many as we requested. With the current
check, the code will try to redistribute even if we did in fact get all
the vectors we requested - this can happen when we have more CPUs than
we do vectors. This restores an earlier check to be sure we only
redistribute if we didn't get the full count we requested.
Fixes: 4ce20abc64 (i40e: fix MSI-X vector redistribution if hw limit is reached)
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A cleanup of the PM code left an incorrect #ifdef in place, leading
to a harmless build warning:
drivers/net/ethernet/intel/i40e/i40e_main.c:12223:12: error: 'i40e_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:12185:12: error: 'i40e_suspend' defined but not used [-Werror=unused-function]
It's easier to use __maybe_unused attributes here, since you
can't pick the wrong one.
Fixes: 0e5d3da400 ("i40e: use newer generic PM support instead of legacy PM callbacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-17
This series contains updates to i40e and ethtool.
Alan provides most of the changes in this series which are mainly fixes
and cleanups. Renamed the ethtool "cmd" variable to "ks", since the new
ethtool API passes us ksettings structs instead of command structs.
Cleaned up an ifdef that was not accomplishing anything. Added function
header comments to provide better documentation. Fixed two issues in
i40e_get_link_ksettings(), by calling
ethtool_link_ksettings_zero_link_mode() to ensure the advertising and
link masks are cleared before we start setting bits. Cleaned up and fixed
code comments which were incorrect. Separated the setting of autoneg in
i40e_phy_types_to_ethtool() into its own conditional to clarify what PHYs
support and advertise autoneg, and makes it easier to add new PHY types in
the future. Added ethtool functionality to intersect two link masks
together to find the common ground between them. Overhauled i40e to
ensure that the new ethtool API macros are being used, instead of the
old ones. Fixed the usage of unsigned 64-bit division which is not
supported on all architectures.
Sudheer adds support for 25G Active Optical Cables (AOC) and Active Copper
Cables (ACC) PHY types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Switches test of .data field to
.function, since .data will be going away.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52eb1ff93e98 ("i40e: Add support setting TC max bandwidth rates")
and commit 1ea6f21ae530 ("i40e: Refactor VF BW rate limiting") add some
needed functionality for TC bandwidth rate limiting. Unfortunately they
introduce several usages of unsigned 64-bit division which needs to be
handled special by the kernel to support all architectures.
Fixes: 52eb1ff93e98 ("i40e: Add support setting TC max bandwidth
rates")
Fixes: 1ea6f21ae530 ("i40e: Refactor VF BW rate limiting")
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables setting up maximum Tx rates for the traffic
classes in i40e. The maximum rate is offloaded to the hardware through
the mqprio framework by specifying the mode option as 'channel' and
shaper option as 'bw_rlimit' and is configured for the VSI. Configuring
minimum Tx rate limit is not supported in the device. The minimum
usable value for Tx rate is 50Mbps.
Example:
# tc qdisc add dev eth0 root mqprio num_tc 2 map 0 0 0 0 1 1 1 1\
queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\
max_rate 4Gbit 5Gbit
To dump the bandwidth rates:
# tc qdisc show dev eth0
qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0
queues:(0:3) (4:7)
mode:channel
shaper:bw_rlimit max_rate:4Gbit 5Gbit
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the BW rate limiting for Tx traffic
on the VF to be reused in the next patch for rate limiting Tx
traffic for the VSIs on the PF as well.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver is modified to enable the new mqprio hardware
offload mode and factor the TCs and queue configuration by
creating channel VSIs. In this mode, the priority to traffic
class mapping and the user specified queue ranges are used
to configure the traffic classes by setting the mode option to
'channel'.
Example:
map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\
hw 1 mode channel
qdisc mqprio 8038: root tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0
queues:(0:1) (2:3) (4:4) (5:5)
mode:channel
shaper:dcb
The HW channels created are removed and all the queue configuration
is set to default when the qdisc is detached from the root of the
device.
This patch also disables setting up channels via ethtool (ethtool -L)
when the TCs are configured using mqprio scheduler.
The patch also limits setting ethtool Rx flow hash indirection
(ethtool -X eth0 equal N) to max queues configured via mqprio.
The Rx flow hash indirection input through ethtool should be
validated so that it is within in the queue range configured via
tc/mqprio. The bound checking is achieved by reporting the current
rss size to the kernel when queues are configured via mqprio.
Example:
map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\
hw 1 mode channel
Cannot set RX flow hash configuration: Invalid argument
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch sets up the infrastructure for offloading TCs and
queue configurations to the hardware by creating HW channels(VSI).
A new channel is created for each of the traffic class
configuration offloaded via mqprio framework except for the first TC
(TC0). TC0 for the main VSI is also reconfigured as per user provided
queue parameters. Queue counts that are not power-of-2 are handled by
reconfiguring RSS by reprogramming LUTs using the queue count value.
This patch also handles configuring the TX rings for the channels,
setting up the RX queue map for channel.
Also, the channels so created are removed and all the queue
configuration is set to default when the qdisc is detached from the
root of the device.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce a macro for the bit setting the PF reset flag and
update its usages. This makes it easier to use this flag
in functions to be introduced in future without encountering
checkpatch issues related to alignment and line over 80
characters.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a typo in i40e_vsi_alloc_arrays() documentation.
The first parameter name should be "vsi" instead of "type".
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recently, the kernel gained support for enabling XPS and QoS at the
same time. Thus, we no longer need to worry about the number of
traffic classes when enabling XPS.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lrxq thresh value tells hardware to immediately interrupt when there
are fewer than N*64 packets left in the ring.
Counter intuitively, empirical testing has shown that decreasing this
value from 2 to 1, and thus changing from an immediate interrupt at
fewer than 128 descriptors down to 64 descriptors causes a small
increase in the maximum total packets per second we can receive. This
increase occurs even when we're polling with interrupts masked, as the
hardware must still handle interrupts internally even if we've disabled
them in software.
Also reduce the value for any VFs we allocate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the past we changed driver behavior to not clear the PBA when
re-enabling interrupts. This change was motivated by the flawed belief
that clearing the PBA would cause a lost interrupt if a receive
interrupt occurred while interrupts were disabled.
According to empirical testing this isn't the case. Additionally, the
data sheet specifically says that we should set the CLEARPBA bit when
re-enabling interrupts in a polling setup.
This reverts commit 40d72a5098 ("i40e/i40evf: don't lose interrupts")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ITR register expects to be programmed in units of 2 microseconds.
Because of this, all of the drivers I40E_ITR_* constants are in terms of
this 2 microsecond register.
Unfortunately, the rx_itr_default value is expected to be programmed in
microseconds.
Effectively the driver defaults to an ITR value of half the expected
value (in terms of minimum microseconds between interrupts).
Fix this by changing the default values to be calculated using
ITR_REG_TO_USEC macro which indicates that we're converting from the
register units into microseconds.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements the PCI error handler reset_prepare and reset_done.
This allows us to handle function level reset. Without this patch we
are unable to perform and recover from an FLR correctly and this will cause
VFs to be unable to recover from an FLR on the PF.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there is no space for more flow director filters and user requested to
add a new one it is rejected by firmware and automatically removed from the
filter list maintained by driver. This behaviour is correct. Afterwards
existing filter can be removed making free slot for the new one. This
however causes the newly added filter to be accepted by firmware but
removed from driver filter list resulting in not showing after issuing
'ethtool -n <dev_name>'.
This happened due to not clearing the variable pf->fd_inv which stores
filter number to be removed from the list when firmware refused to add the
requested filter. It caused the filter with this specific ID to be
constantly removed once it was added to the list although it has been
accepted by firmware and effectively applied to the NIC.
It was fixed by clearing pf->fd_inv variable after removal of the filter
from the list when it was rejected by firmware.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch causes error message to be displayed when NIC detects
insertion of module that does not meet thermal requirements.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes some code that was accidentally added to
the wrong function with a merge error. Fixes: c53934c6d1
("i40e: fix: do not sleep in netdev_ops")
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using set_bit and friends, we should be using actual
bitmaps, and fix all the locations where we might access
it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Starting with XL710 FW 5.3 PTP L4 was disabled for XL710 due to a bug. The
bug has since been resolved in XL710 FW >6.0 and PTP L4 can now be
re-enabled on those devices with updated firmware.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, when setting up the IRQ for a q_vector, we set an affinity
hint based on the v_idx of that q_vector. Meaning a loop iterates on
v_idx, which is an incremental value, and the cpumask is created based
on this value.
This is a problem in systems with multiple logical CPUs per core (like in
simultaneous multithreading (SMT) scenarios). If we disable some logical
CPUs, by turning SMT off for example, we will end up with a sparse
cpu_online_mask, i.e., only the first CPU in a core is online, and
incremental filling in q_vector cpumask might lead to multiple offline
CPUs being assigned to q_vectors.
Example: if we have a system with 8 cores each one containing 8 logical
CPUs (SMT == 8 in this case), we have 64 CPUs in total. But if SMT is
disabled, only the 1st CPU in each core remains online, so the
cpu_online_mask in this case would have only 8 bits set, in a sparse way.
In general case, when SMT is off the cpu_online_mask has only C bits set:
0, 1*N, 2*N, ..., C*(N-1) where
C == # of cores;
N == # of logical CPUs per core.
In our example, only bits 0, 8, 16, 24, 32, 40, 48, 56 would be set.
Instead, we should only assign hints for CPUs which are online. Even
better, the kernel already provides a function, cpumask_local_spread()
which takes an index and returns a CPU, spreading the interrupts across
local NUMA nodes first, and then remote ones if necessary.
Since we generally have a 1:1 mapping between vectors and CPUs, there
is no real advantage to spreading vectors to local CPUs first. In order
to avoid mismatch of the default XPS hints, we'll pass -1 so that it
spreads across all CPUs without regard to the node locality.
Note that we don't need to change the q_vector->affinity_mask as this is
initialized to cpu_possible_mask, until an actual affinity is set and
then notified back to us.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
By default, our devices do source pruning, that is, they drop receive
packets that have the source MAC matching one of the receive filters.
Unfortunately, this breaks ARP monitoring in channel bonding, as the
bonding driver expects devices to receive ARPs containing their own
source address.
Add an ethtool private flag to control this feature.
Also, remove the netif_running() check when we process our private
flags. It's OK to reset when the device is closed and in most cases we
need the reset the apply these changes.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable i40e to pass traffic with VLAN tags using the 802.1ad ethernet
protocol ID (0x88a8).
This requires NIC firmware providing version 1.7 of the API. With
older NIC firmware 802.1ad tagged packets will continue to be dropped.
No VLAN offloads nor RSS are supported for 802.1ad VLANs.
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a machine has more CPUs than queue pairs, e.g. 512 cores, the
counting gets a little funky and turns off Flow Director with the
message:
not enough queues for Flow Director. Flow Director feature is disabled
This patch limits the number of lan queues initially allocated to
be sure we have some left for FD and other features.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver now supports two different devices with two different
firmware versions. So be smart about how we handle these. Move the FW
version macros to the appropriate header file, and add a convenience
macro that checks the version based on the device. Then use this macro
to check whether or not the driver can use the new link info API.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On some platforms with a large number of CPUs, we will allocate many IRQ
vectors. When hibernating, the system will attempt to migrate all of the
vectors back to CPU0 when shutting down all the other CPUs. It is
possible that we have so many vectors that it cannot re-assign them to
CPU0. This is even more likely if we have many devices installed in one
platform.
The end result is failure to hibernate, as it is not possible to
shutdown the CPUs. We can avoid this by disabling MSI-X and clearing our
interrupt scheme when the device is suspended. A more ideal solution
would be some method for the stack to properly handle this for all
drivers, rather than on a case-by-case basis for each driver to fix
itself.
However, until this more ideal solution exists, we can do our part and
shutdown our IRQs during suspend, which should allow systems with
a large number of CPUs to safely suspend or hibernate.
It may be worth investigating if we should shut down even further when
we suspend as it may make the path cleaner, but this was the minimum fix
for the hibernation issue mentioned here.
Testing-hints:
This affects systems with a large number of CPUs, and with multiple
devices enabled. Without this change, those platforms are unable to
hibernate at all.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although the service task does check the suspended status before
running, it might already be part way through running when we go to
suspend. Lets ensure that the service task is stopped and will not be
restarted again until we finish resuming. This ensures that service task
code does not cause strange interactions with the suspend/resume
handlers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When handling suspend and resume callbacks we want to make sure that (a)
we don't suspend again if we're already suspended and (b) we don't
resume again if we're already resuming. Lets make sure we test_and_set
the __I40E_SUSPENDED bit in i40e_suspend which ensures that a suspend
call when already suspended will exit early. Additionally, if
__I40E_SUSPENDED is not set when we begin resuming, exit early as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop using the old legacy PM support, since we now have stable support
for the newer generic PM callbacks.
This has several advantages. First, we no longer have to manage our
own pci_save_state() and power changes, as it's preferred to have the
PCI stack do this. Second, these routines get called for both hibernate
and suspend to ram, so we can have the driver properly handle all the
suspend/resume flows that it needs to.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We currently (mis)use the __I40E_RECOVERY_PENDING bit to determine when
we should actually request a new IRQ in i40e_setup_misc_vector().
This led to a design mistake where we open-coded the re-setup of the
miscellaneous vector in i40e_resume() instead of using the function
provided. If we did not open-code this and instead tried to use the
i40e_setup_misc_vector() function, it would lead to never reallocating
the IRQ.
This would lead to a second i40e_suspend() call failing to free the
vector due to a NULL pointer dereference.
A future patch is going to re-work how the i40e_suspend() and
i40e_resume() flows work to clear all IRQ vectors, which would require
us to use i40e_setup_misc_vector() directly. Since during this time the
__I40E_RECOVERY_PENDING bit is set, we'll never re-allocate the vector.
Rather than leaving the open-coded setup in i40e_resume() lets just fix
the problem properly in i40e_setup_misc_vector().
Introduce a new state bit which indicates when the IRQ has been
assigned, which will be set when i40e_setup_misc_vector is first called.
This ultimately resolves the issue of re-requesting the vector, without
overloading the __I40E_RECOVERY_PENDING state. This ensures that the
suspend/resume cycle can use the setup function instead of open-coding
the re-request during resume.
Additionally, since the only callers of i40e_stop_misc_vector also want
to free it, move this code directly into the function to avoid
duplication. Due to the new functionality, rename it to
i40e_free_misc_vector().
This lets us drop the extra calls to free and re-enable the vector
during i40e_suspend() and i40e_resume(). We don't need to call
i40e_setup_misc_Vector() in i40e_resume() because it gets called by the
i40e_rebuild() call.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
An errata with GLQF_PCNT causes it to not wrap as expected. This
can cause an error in flow director statistics. This patch resets
affected counters just after reading.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fortville and Fort Park devices are often on different firmware release
schedules. This change relaxes the minor version warning message,
so it is only displayed for older FW warning version for old
firmware Fortville 3 or earlier.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit replaces usage of vsi->back in i40e_print_link_message()
(which is actually a PF pointer) with temp variable.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_print_link_message() is intended to compare new
link state with current link state and print log message
only if the new state is different from current state.
However in current driver the new state does not get updated
when link is going down because of the if condition. When an
interface is brought down, vsi->state is set to I40E_VSI_DOWN
in i40e_vsi_close() and later i40e_print_link_message() does
not get invoked in i40e_link_event due to if condition. Hence
link down message doesn't appear when link is going down. The
down state is seen later during i40e_open() and old state
gets printed. The actual link state doesn't get updated in
i40e_close() or i40e_open() but when i40e_handle_link_event is
called inside i40e_clean_adminq_subtask.
This change allows i40e_print_link_message() to be called when
interface is going down and keeps the state information updated.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In current driver, when ifconfig ethx up is done, the link state
doesn't transition to UP inside i40e_open(). It changes after AQ
command response is handled in i40e_handle_link_event().
When pf->hw.phy.link_info.link_info is DOWN inside i40e_open(),
The state is transient and invalid. So log message gets printed
based on incorrect info (i.e link_info and an_info).
This commit removes check for unqualified module inside
i40e_up_complete(). The existing check in i40e_handle_link_event()
logs the error message based on correct link state information.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On older kernels a call to irq_set_affinity_hint does not guarantee that
the IRQ affinity will be set. If nothing else on the system sets the IRQ
affinity this can result in a bug in the i40e_napi_poll() routine where
we notice that our interrupt fired on the "wrong" CPU according to our
internal affinity_mask variable.
This results in a bug where we continuously tell NAPI to stop polling to
move the interrupt to a new CPU, but the CPU never changes because our
affinity mask does not match the actual mask setup for the IRQ.
The root problem is a mismatched affinity mask value. So lets initialize
the value to cpu_possible_mask instead. This ensures that prior to the
first time we get an IRQ affinity notification we'll have the mask set
to include every possible CPU.
We use cpu_possible_mask instead of cpu_online_mask since the former is
almost certainly never going to change, while the later might change
after we've made a copy.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 3ffa037d7f ("i40e: Set XPS bit mask to zero in DCB mode")
we've tried to reset the XPS settings by building a custom
empty CPU mask.
This workaround is not necessary because we're not really removing the
XPS setting, but simply setting it so that no CPU is valid.
Second, we shorten the code further by using zalloc_cpumask_var instead
of a separate call to bitmap_zero().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where an error return value is
set, but without an immediate exit, the value can be overwritten
by the following code execution. The condition at this point
is not fatal, so remove the error assignment and comment the
intent for future code maintainers
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch improves the system log message. The log message will
be expanded to include the FEC mode the FW requested before link
was established.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In new versions of GCC since 7.x a new warning exists which warns when
a string is truncated before all of the format can be completed.
When we setup VMDQ netdev names we are copying a pre-existing interface
name which could be up to 15 characters in length. Since we also add
4 bytes, v, the literal %, the d and a \0 null, we would overrun the
available size unless snprintf truncated for us.
The snprintf call will of course truncate on the end, so lets instead
modify the code to force truncation of the copied netdev name by
4 characters, to create enough space for the 4 bytes we're adding.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the header file cpumask.h, we shouldn't be directly copying
a cpumask_t, since its a bitmap and might not be copied correctly. Lets
use the provided cpumask_copy() function instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40e_vsi_add_vlan we treat attempting to add VID=0 as an error,
because it does not do what the caller might expect. We already special
case VID=0 in i40e_vlan_rx_add_vid so that we avoid this error when
adding the VLAN.
This special casing is necessary so that we do not add the VLAN=0 filter
since we don't want to stop receiving untagged traffic. Unfortunately,
not all callers of i40e_vsi_add_vlan are aware of this, including when
we add VLANs from a VF device.
Rather than special casing every single caller of i40e_vsi_add_vlan,
lets just move this check internally. This makes the code simpler
because the caller does not need to be aware of how VLAN=0 is special,
and we don't forget to add this check in new places.
This fixes a harmless error message displaying when adding a VLAN from
within a VF. The message was meaningless but there is no reason to
confuse end users and system administrators, and this is now avoided.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem with the HW ATR eviction feature where the
NVM setting was incorrect. This patch detects the issue on X720
adapters and disables the feature if the NVM setting is incorrect.
Without this patch, HW ATR Evict feature does not work on broken NVMs
and is not detected either. If the HW ATR Evict feature is disabled
the SW Eviction feature will take effect.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit b499ffb0a2 ("i40e: Look up MAC address in Open Firmware
or IDPROM"), we've had support for obtaining the MAC address
form Open Firmware or IDPROM.
This code relied on sending the Open Firmware address directly to the
device firmware instead of relying on our MAC/VLAN filter list. Thus,
a work around was introduced in commit b1b15df592 ("i40e: Explicitly
write platform-specific mac address after PF reset")
We refactored the Open Firmware address enablement code in the ill-named
commit 41c4c2b50d ("i40e: allow look-up of MAC address from Open
Firmware or IDPROM")
Since this refactor, we no longer even set I40E_FLAG_PF_MAC. Further, we
don't need this work around, because we actually store the MAC address
as part of the MAC/VLAN filter hash. Thus, we will restore the address
correctly upon reset.
The refactor above failed to revert the workaround, so do that now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of flags found in pf->flags has grown quite large, and there
are a lot of different types of flags. Most of the flags are simply
hardware features which are enabled on some firmware or some MAC types.
Other flags are dynamic run-time flags which enable or disable certain
features of the driver.
Separate these two types of flags into pf->hw_features and pf->flags.
The hw_features list will contain a set of features which are enabled at
init time. This will not contain toggles or otherwise dynamically
changing features. These flags should not need atomic protections, as
they will be set once during init and then be essentially read only.
Everything else will remain in the flags variable. These flags may be
modified at any time during run time. A future patch may wish to convert
these flags into set_bit/clear_bit/test_bit or similar approach to
ensure atomic correctness.
The I40E_FLAG_MFP_ENABLED flag may be a good fit for hw_features but
currently is used by ethtool in the private flags settings, and thus has
been left as part of flags.
Additionally, I40E_FLAG_DCB_CAPABLE may be a good fit for the
hw_features but this patch has not tried to untangle it yet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X722 pf flag setup should happen before the VMDq RSS queue count is
initialized for VMDq VSI to get the right number of queues for RSS in
case of X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the kernel supports double VLAN tags, we should at least play
nice. Adjust the max packet size to account for two VLAN tags, not just
one.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill the XDP prog_id with the id just like we do in other XDP enabled
drivers such as ixgbe. This is needed so that on dump we can retrieve
the attached program based on the id, and dump BPF insns, opcodes, etc
back to user space. Only XDP driver missing this is currently i40e.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver attempts to display the UDP tunnel name by doing a check
against the type, where for non-zero types we use "vxlan" and for zero
type we use "geneve". This is not future proof, because if new tunnel
types get added, we'll incorrectly label them. It also depends on the
value of UDP_TUNNEL_TYPE_GENEVE == 0, which is brittle.
Instead, replace this with a function that can return a constant string
depending on the type. For now we'll use "unknown" for types we don't
know about, and we can expand this in the future if new types get added.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiler reported several places where driver compared
signed and unsigned types. Cast or change the types to remove
the warnings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During certain events such as a CORER, multiple devices will run a work
task to handle some cleanup. This can cause issues due to
a single-threaded workqueue which can mean that a device doesn't cleanup
in time. Prevent this by removing the single-threaded restriction on the
module workqueue. This avoids the need to add more complex yielding
logic in our service task routine. This is also similar to what other
drivers such as fm10k do.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem found in systems when entering
S4 state. This patch fixes the problem by ensuring that
the misc vector's IRQ is disabled as well. Without this
patch a stack trace can be seen upon entering S4 state.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We recently refactored i40e_do_reset() and its friends to be able to
hold the RTNL lock only for the portions that actually need to be
protected. However, a separate refactoring added several new callers of
these functions during the PCIe error recovery and suspend/resume
cycles.
When merging the changes together, it was not noticed that we could
reduce the RTNL scope by letting the reset function handle the lock
itself, as previously it was not possible.
Fix this by replacing these call sites to indicate that the reset
function should handle its own lock. This enables multiple PFs to reset
or resume simultaneously without serializing the resets via the RTNL
lock. The end result is that on systems with lots of PFs and VFs the
resets don't stall waiting for each other to finish.
It is probable that we can also do the same for i40e_do_reset_safe, but
this author did not research that change carefully enough to be
confident.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When IWARP is enabled, we weren't clearing the PE_CRITERR, just logging
it and removing it from the mask. We need to do a corer to reset the
PE_CRITERR register, so set the bit for that as we handle the
interrupt.
We should also be checking for the error against the PFINT_ICR0 register,
and only need to clear it in the value getting written to
PFINT_ICR0_ENA.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When disabling interrupts, we should only be clearing the CAUSE_ENA bit,
not clearing the whole register. Clearing the whole register sets the
NEXTQ_IDX field to 0 instead of 0x7ff which can confuse the Firmware in
some reset sequences.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which the driver does not correctly exit overflow
promiscuous mode. This can occur if "too many" mac filters are added,
putting the driver into overflow promiscuous mode, and the filters are
then removed. When the failed filters are removed, the driver reports
exiting overflow promiscuous mode which is correct, however traffic
continues to be received as if in promiscuous mode still.
The bug occurs because the conditional for toggling promiscuous mode was
set to only execute when promiscuous mode was enabled and not when it
was disabled as well. This patch fixes the conditional to correctly
execute when promiscuous mode is toggled and not just enabled. Without
this patch, the driver is unable to correctly exit overflow promiscuous
mode.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for OEM firmware version. If OEM specific
adapter is detected ethtool reports OEM product version in firmware
version string instead of etrack id.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Partition bandwidth control is not in just one form of MFP (multi-function
partitioning), so make the code more generic and be sure to nudge the Tx
scheduler for all MFP.
Copyright updated to 2017.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds proper XDP_TX action support. For each Tx ring, an
additional XDP Tx ring is allocated and setup. This version does the
DMA mapping in the fast-path, which will penalize performance for
IOMMU enabled systems. Further, debugfs support is not wired up for
the XDP Tx rings.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds basic XDP support for i40e derived NICs. All XDP
actions will end up in XDP_DROP.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:
[49.013] i40e 0002:01:00.0: bad reset request 0x00000020
Commit d19cb64b92 ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.
This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.
Fixes: 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b92 ("i40e: separate PF and VSI state flags")
Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an i40e_ptp_tx_hang() function similar to the already existing
i40e_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There's no reason to pass a *vsi pointer if we already have the *pf
pointer in the only location where we call this function. Lets update
the signature and directly pass the *pf data structure pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.
Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.
Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.
Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.
Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.
This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation
s/&(vsi->back|vsi|pf)->state/\1->state/
s/&adapter->vsi.state/adapter->vsi.state/
For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid using the same named flags for both vsi->state and pf->state. This
makes code review easier, as it is more likely that future authors will
use the correct state field when checking bits. Previous commits already
found issues with at least one check, and possibly others may be
incorrect.
This reduces confusion as it is more clear what each flag represents,
and which flags are valid for which state field.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The delay was added because of a desire to ensure that the VF driver can
finish up removing. However, pci_disable_sriov already has its own
ssleep() call that will sleep for an entire second, so there is no
reason to add extra delay on top of this by using msleep here. In
practice, an msleep() won't have a huge impact on timing but there is no
real value in keeping it, so lets just simplify the code and remove it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a major oversight in that we were not reprogramming the
ports after a reset. As a result we completely lost all of the Rx tunnel
offloads on receive including Rx checksum, RSS on inner headers, and ATR.
The fix for this is pretty standard as all we needed to do is reset the
filter bits to pending for all active filters and schedule the sync event.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The .index field of i40e_udp_port_config represents the udp port number.
Rename this variable to port so that it is more obvious.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These flags represent the state of the VF at various times. Do not
spell them as _STAT_ which can be confusing to readers who may think
these refer to statistics.
Change-ID: I6bc092cd472e8276896a1fd7498aced2084312df
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This state bit was added as a way for DCB to avoid having to wait for
the queues to disable when handling LLDP events. The logic for this was
burried deep within stop Tx and stop Rx queue code. First, let's rename
it so that it does not appear to only affect Tx when infact it modifies
both Tx and Rx flow. Second we can move it up into the i40e_stop_rings()
function, and we can simply re-use the i40e_stop_rings_no_wait() so that
we don't have to bury the implementation as deep into the call stack.
An alternative might be to remove the state bit and instead attempt to
shut down everything directly in DCP flow. This, however, is not ideal
because it creates yet another separate shutdown routine that we'd have
to maintain. In the current implementation any changes will be made to
both flows.
Change-ID: I68e1ccb901af320862bca395e9c9746f08e8b17c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there are a lot of active VFs, it can take multiple seconds to
finish resetting all of them during certain flows., which can cause some
VFs to fail to wait long enough for the reset to occur. The user might
see messages like "Never saw reset" or "Reset never finished" and the VF
driver will stop functioning properly.
The naive solution would be to simply increase the wait timer. We can
get much more clever. Notice that i40e_reset_vf is run in a serialized
fashion, and includes lots of delays.
There are two prominent delays which take most of the time. First, when
we begin resetting VFs, we have multiple 10ms delays which accrue
because we reset each VF in a serial fashion. These delays accumulate to
almost 4 seconds when handling the maximum number of VFs (128).
Secondly, there is a massive 50ms delay for each time we disable queues
on a VSI. This delay is necessary to allow HW to finish disabling queues
before we restore functionality. However, just like with the first case,
we are paying the cost for each VF, rather than disabling all VFs and
waiting once.
Both of these can be fixed, but required some previous refactoring to
handle the special case. First, we will need the
i40e_vsi_wait_queues_disabled function which was previously DCB
specific. Second, we will need to implement our own
i40e_vsi_stop_rings_no_wait function which will handle the stopping of
rings without the delays.
Finally, implement an i40e_reset_all_vfs function, which will first
start the reset of all VFs, and pay the wait cost all at once, rather
than serially waiting for each VF before we start processing then next
one. After the VF has been reset, we'll disable all the VF queues, and
then wait for them to disable. Again, we'll organize the flow such that
we pay the wait cost only once.
Finally, after we've disabled queues we'll go ahead and begin restoring
VF functionality. The result is reducing the wait time by a large factor
and ensuring that VFs do not timeout when waiting in the VF driver.
Change-ID: Ia6e8cf8d98131b78aec89db78afb8d905c9b12be
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch will need to be able to handle controlling queues without
waiting until all VSIs are handled. Factor out the direct queue
modification so that we can easily re-use this code. The result is also
a bit easier to read since we don't embed multiple single-letter loop
counters.
Change-ID: Id923cbfa43127b1c24d8ed4f809b1012c736d9ac
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We made some effort to reduce the RTNL lock scope when resetting and
rebuilding the PF. Unfortunately we still held the RTNL lock during the
VF reset operation, which meant that multiple PFs could not reset in
parallel due to the global lock. For now, further reduce the scope by
not holding the RTNL lock while resetting VFs. This allows multiple PFs
to reset in a timely manner.
Change-ID: I2fbf823a0063f24dff67676cad09f0bbf83ee4ce
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds tracepoints to the i40e and i40evf drivers to which
BPF programs can be attached for feature testing and verification.
It's expected that an attached BPF program will identify and count or
log some interesting subset of traffic. The bcc-tools package is
helpful there for containing all the BPF arcana in a handy Python
wrapper. Though you can make these tracepoints log trace messages, the
messages themselves probably won't be very useful (other to verify the
tracepoint is being called while you're debugging your BPF program).
The idea here is that tracepoints have such low performance cost when
disabled that we can leave these in the upstream drivers. This may
eventually enable the instrumentation of unmodified customer systems
should the need arise to verify a NIC feature is working as expected.
In general this enables one set of feature verification tools to be
used on these drivers whether they're built with the kernel or
separately.
Users are advised against using these tracepoints for anything other
than a diagnostic tool. They have a performance impact when enabled,
and their exact placement and form may change as we see how well they
work in practice for the purposes above.
Change-ID: Id6014a7322c0e6d08068114dd20bd156f2f6435e
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds padding to the start of frames to make room for headroom
for us to eventually start using build_skb. Right now we guarantee at
least NET_SKB_PAD + NET_IP_ALIGN, however we allocate more space if more is
available. For example on x86 the headroom should be 192 bytes.
On systems that have too large of a cache line size to support storing 1.5K
padding and shared info we default to using 3K buffers and reserve
everything that isn't used for skb_shared_info or the data buffer for
headroom.
Change-ID: I33c641c9a1ea10cf7cc484c2d20985368d2d709a
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are situations where adding padding to the front and back of an Rx
buffer will require that we add additional padding. Specifically if
NET_IP_ALIGN is non-zero, or the MTU size is larger than 7.5K we would need
to use 2K buffers which leaves us with no room for the padding.
To preemptively address these cases I am adding support for 3K buffers to
the Rx path so that we can provide the additional padding needed in the
event of NET_IP_ALIGN being non-zero or a cache line being greater than 64.
Change-ID: I938bc1ba611285428df39a613cd66f98e60b55c7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag
definitions.
Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can simply check both Tx and Rx queues in a single loop, rather than
repeating the loop twice.
Change-ID: Ic06f26b0e3c2620e0e33c1a2999edda488e647ad
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Look up the MAC address from the eth_get_platform_mac_address() function
first before checking what the firmware provides. We already handle the
case of re-writing the MAC-VLAN filter, so there is no need to add extra
code for this. However, update the comment where we do this to indicate
that it does impact the Open Firmware MAC address case.
Change-ID: I73e59fbe0b0e7e6f3ee9f5170d0bd3a4d5faf4db
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path. The previous implementation
set a 'hung bit' which would then get cleared while polling. If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt. This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.
Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.
Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously rtnl lock was held during whole reset procedure that
was stopping other PFs running their reset procedures. In the result
reset was not handled properly and host reset was the only way
to recover.
Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954
Signed-off-by: Maciej Sosin <maciej.sosin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The client interface is only intended for use on devices that support
iWarp. Only register with the client if this is the case.
This fixes a panic when loading i40iw on X710 devices.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the driver is removed or shut down, close any attached clients
(i.e. i40iw). This prevents a panic seen sometimes on forced driver
removal or system shutdown when iWarp is running.
Change-ID: I4f6161e5a73ffbb2fd5883567b007310302bfcb5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a capability negotiation between VF and PF using ENCAP/
ENCAP_CSUM offload flags in order for the VF to support outer checksum
and TSO offloads for encapsulated packets. These capabilities were assumed
by default and enabled in current hardware. Going forward, these features
needs to be negotiated with PF before advertising to the stack.
Additionally, strip out the mac.type checks for X722 since outer checksums
are enabled based on the ENCAP_CSUM offload negotiation flag and maintain
consistency between drivers in how the features are configured.
Change-ID: Ie380a6f57eca557a2bb575b66b12fae36d308920
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a delay to Rx queue disables to accommodate HW needs.
v2: Added missing check for disable only, additional details on the
need for the ugly delay and fixed spacing on comment.
Change-ID: I2864ca667ce5dcc2cc44f8718113b719742a46a1
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way we handle the maximum frame size for the Rx
path. Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount. With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size. This makes the behavior more
consistent with the other drivers such as igb which had similar logic. In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.
Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The goto found here for when in MFP mode is pointless. It jumps to the
end of a series of if blocks. However, right after this statement is
a closing '}' for this if block, which will result in the program flow
going to the exact same location as the goto statement indicates. Thus,
regardless of whether we are in MFP mode, the program flow will resume
from the same location.
This arose due to various refactoring which did not notice that this
goto became essentially a no-op.
To properly understand this diff you will need to view a larger context
than is given by default.
Change-ID: I088f73c3831aa5c4e2281380c7a3ce605594300c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a case where we miss an arq element if a new one is added before we
enable interrupts and exit the arq subtask loop. This occurs frequently
with RDMA running on Windows VF and causes long delays that prevent SMB
from establishing connections.
Change-ID: I3e1c8b2b960c12857d9b8275bea2c1563674392e
Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since FCoE isn't supported by the i40e products there isn't much point in
carrying around code that will always evaluate to false. This patch goes
through and strips out the code in several spots so that we don't go around
carrying variables and/or code that is always going to evaluate to false or
0.
Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed no longer needed delays. At preproduction stage those delays were
needed but now these delays are not needed.
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in the driver where the calculation of the
RSS size was not taking into account the number of traffic classes
enabled. This patch factors in the traffic classes both in
the initial configuration of the table as well as reconfiguration.
Change-ID: I34dcd345ce52faf1d6b9614bea28d450cfd5f621
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When testing the epoll w/ busy poll code I found that I could get into a
state where the i40e driver had q_vectors w/ active NAPI that had no rings.
This was resulting in a divide by zero error. To correct it I am updating
the driver code so that we only support NAPI on q_vectors that have 1 or
more rings allocated to them.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a complex if->continue->else->break construction in
i40e_next_filter. We can simply use hlist_for_each_entry_continue
instead. This drops a lot of confusing code. The resulting code is much
easier to understand the intention, and follows the more normal pattern
for using hlist loops. We could have also used a break with a "return
next" at the end of the function, instead of return NULL, but the
current implementation is explicitly clear that when you reach the end
of the loop you get a NULL value. The alternative construction is less
clear since the reader would have to know that next is NULL at the end
of the loop.
Change-Id: Ife74ca451dd79d7f0d93c672bd42092d324d4a03
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable FDir filters for SCTPv4 packets using the ethtool ntuple
interface to enable filters. The ethtool API does not allow masking on
the verification tag.
Change-Id: I093e88a8143994c7e6f4b7b17a0bd5cf861d18e4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for flexible payloads passed via ethtool user-def field.
This support is somewhat limited due to hardware design. The input set
can only be programmed once per filter type, and the flexible offset is
part of this filter input set. This means that the user cannot program
both a regular and a flexible filter at the same time for a given flow
type. Additionally, the user may not program two flexible filters of the
same flow type with different offsets, although they are allowed to
configure different values at that offset location.
We support a single flexible word (2byte) value per protocol type, and
we handle the FLX_PIT register using a list of flexible entries so that
each flow type may be configured separately.
Due to hardware implementation, the flexible data is offset from the
start of the packet payload, and thus may not be in part of the header
data. For this reason, the offset provided by the user defined data is
interpreted as a byte offset from the start of the matching payload.
Previous implementations have tried to represent the offset as from the
start of the frame, but this is not feasible because header sizes may
change due to options.
Change-Id: 36ed27995e97de63f9aea5ade5778ff038d6f811
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ensure that the default input set is correctly reprogrammed when
cleaning up after disabling flow director support. This ensures that the
programmed value will be in a clean state.
Although we do not yet have support for SCTPv4 filters, a future patch
will add support for this protocol, so we will correctly restore the
SCTPv4 input set here as well. Note that strictly speaking the default
hardware value for SCTP includes matching the verification tag. However,
the ethtool API does not have support for specifying this value, so
there is no reason to keep the verification field enabled.
This patch is the next step on the way to enabling partial tuple filters
which will be implemented in a following patch.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When flushing and replaying FDIR filters, it is possible we would
disable ATR, and then re-enable it even though we should have kept
it disabled due to existing TCP/IPv4 filters. Fix this by checking
whether we have TCP4/IPv4 filters before re-enabling.
Alternatively, we could instead restore ATR and then replay filters,
however, this would cause us to rapidly enable and then disable ATR in
some cases.
Change-ID: I076e4cc1e4409bce7f98f3c213295433a4ff43d8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we're about to reprogram the filters, we need to ensure that the
fd_tcp_rule count is correctly reset to 0. Otherwise, we will keep
a stale count that does not accurately reflect the number of programmed
TCPv4 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fdir_filter_restore re-adds all existing filters, which already
checks when adding a TCPv4 filter to disable ATR. We don't need to make
the check twice, so remove this redundant code.
Change-ID: Ia0b0690e23523915199d601494557def135c9d7f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.
This patch essentially reverts b3f5c7bc88 ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.
Fixes: b3f5c7bc88 ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.
Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch clarifies the reason for removal of automatically
firmware-generated filter and explicit addition of filter which
accepts frames with any VLAN id.
Change-ID: Iabf180b6d61c4d8a36d3bcf8457c377a6f2aca0e
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue that RSS offloading only works on PF0 by
using the direct register writing of the hash keys for the VFs instead
of using the admin queue command to do so.
Change-ID: Ia02cda7dbaa23def342e8786097a2c03db6f580b
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a solution to avoid adding too many queues to num_lan_msix.
A recent refactor of queue pairs accidentally added all remaining
vectors to the num_lan_msix which can have adverse performance issues,
due to enabling more queues than the number of CPU cores.
This patch removes the old calculation, and replaces it with a simple
algorithm.
1) add queue pairs up to num_online_cpus(), but capped at half of total
vectors
2) then add alternative features such as flow directory and similar
3) finally, add the remaining vectors back to queue pairs, but capped
such that the total number of queue pairs does not exceed
num_online_cpus().
Change-ID: I668abf67d5011a1248866daba8885f4ff00cb8d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(KISS is Keep It Simple, Stupid. Or is it?)
The client interface vastly overengineered for what it needs to do.
It was originally designed to support multiple clients on multiple
netdevs, possibly even with multiple drivers. None of this happened,
and now we know that there will only ever be one client for i40e
(i40iw) and one for i40evf (i40iwvf). So, time for some KISS. Since
i40e and i40evf are a Dynasty, we'll simplify this one to match the
VF interface.
First, be a Destroyer and remove all of the lists and locks required
to support multiple clients. Keep one static around to keep track of
one client, and track the client instances for each netdev in the
driver's pf (or adapter) struct. Now it's Almost Human.
Since we already know the client type is iWarp, get rid of any checks
for this. Same for VSI type - it's always going to be the same type,
so it's just a Parasite.
While we're at it, fix up some comments. This makes the function
headers actually match the functions.
These changes reduce code complexity, simplify maintenance,
squash some lurking timing bugs, and allow us to Rock and Roll All
Nite.
Change-ID: I1ea79948ad73b8685272451440a34507f9a9012e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following message is logged from time to time when using i40e:
NOHZ: local_softirq_pending 08
i40e may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame. The problem is the same as what was
described in commit ec13ee8014 ("virtio_net: invoke softirqs after
__napi_schedule") and this patch applies the same fix to i40e.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists an intermittent bug which causes the 'Link Detected'
field reported by the 'ethtool <iface>' command to be 'Yes' when
in fact, there is no link. This patch fixes the problem by
enabling temporary link polling when i40e_get_link_status returns
an error. This causes the driver to remember that an admin queue
command failed and polls, until the function returns with a success.
Change-Id: I64c69b008db4017b8729f3fc27b8f65c8fe2eaa0
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This ensures that the pvid which is stored in __le16 format is converted
to the CPU format. This will fix comparison issues on Big Endian
platforms.
Change-ID: I92c80d1315dc2a0f9f095d5a0c48d461beb052ed
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This call is made just prior to running i40e_link_event. In
i40e_link_event, we set hw->phy.get_link_info to true just prior to
calling i40e_get_link_status, which conveniently runs
i40e_update_link_info for us. Thus, we are running i40e_update_link_info
twice, which seems like something we don't need to do...
Change-ID: I36467a570f44b7546d218c99e134ff97c2709315
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a call to the mac_address_write admin q function during
power down to update the PRTPM_SAH/SAL registers with the MC_MAG_EN bit
thus enabling multicast magic packet wakeup.
A FW workaround is needed to write the multicast magic wake up enable
bit in the PRTPM_SAH register. The FW expects the mac address write
admin q cmd to be called first with one of the WRITE_TYPE_LAA flags
and then with the multicast relevant flags.
*Note: This solution only works for X722 devices currently. A PFR will
clear the previously mentioned bit by default, but X722 has support for a
WOL_PRESERVE_ON_PFR flag which prevents the bit from being cleared. Once
other devices support this flag, this solution should work as well.
Change-ID: I51bd5b8535bd9051c2676e27c999c1657f786827
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which the driver is unable to exit overflow
promiscuous mode after having added "too many" mac filters. It is
expected that after triggering overflow promiscuous, removing the
failed/extra filters should then disable overflow promiscuous mode.
The bug exists because we were intentionally skipping the sync_vsi_filter
path in cases where we were removing failed filters since they shouldn't
have been added to the firmware in the first place, however we still
need to go through the sync_vsi_filter code path to determine whether or
not it is ok to exit overflow promiscuous mode. This patch fixes the
bug by making sure we go through the sync_vsi_filter path in cases of
failed filters.
Change-ID: I634d249ca3e5fa50729553137c295e73e7722143
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
