The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.
Fixes: ca89319483 ("net: dsa: b53: Keep CPU port as tagged in all VLANs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume in the bcm_sf2 driver that the DSA master network device
supports ethtool_ops::{get,set}_wol operations, which is not a given.
Avoid de-referencing potentially non-existent function pointers and
check them as we should.
Fixes: 96e65d7f3f ("net: dsa: bcm_sf2: add support for Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS. The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions. The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag offload_fwd_mark is set as the switch can forward frames by
itself.
This can be considered a fix to a problem introduced in commit
c2e866911e where the port membership are not set in sync. The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.
Fixes: c2e866911e ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using an external PHY, ports 9 and 10 can support 2500BaseT.
So set this link mode in the mask when validating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the source and destination port of a CFP rule match, we must set
the loopback bit enable to allow that, otherwise the frame is discarded.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return CFP policer statistics (Green, Yellow or Red) as part of the
standard ethtool statistics. This helps debug when CFP rules may not be
hit (0 counter).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding CFP statistics, we will need to overlay the
standard B53 statistics, so create specific bcm_sf2_sw_* functions to
call into their b53_common.c counterpart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need a dedicated statistics mutex since we leverage
b53_common for statistics now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Fixes: b2ddc48a81 ("net: dsa: b53: Do not fail when IRQ are not initialized")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update this driver to use the flow_rule infrastructure, hence we can use
the same code to populate hardware IR from ethtool_rx_flow and the
cls_flower interfaces.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU port vector contains a bit per port of the switch. The code
wrongly used it as a port number, and incremented a port counter. This
resulted in the wrong interfaces counter being incremented, and
potentially going off the end of the array of ports.
Fix this by using the source port ID for the violation, which really
is a port number.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Tested-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 65f60e4582 ("net: dsa: mv88e6xxx: Keep ATU/VTU violation statistics")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MediaTek MT7621 SoC device contains a 7530 switch, and the existing
linux kernel 7530 DSA switch driver can be used with it.
The bulk of the changes required stem from the 7621 having different
regulator and pad setup. The existing setup of these in the 7530
driver appears to be very specific to its implemtation in the Mediatek
7623 SoC. (Not entirely surprising given the 7623 is a quad core ARM
based SoC, and the 7621 is a dual core, dual thread MIPS based SoC).
Create a new devicetree type, "mediatek,mt7621", to support the 7530
switch in the 7621 SoC. There appears to be no usable ID register to
distinguish it from a 7530 in other hardware at runtime. This is used
to carry out the appropriate configuration and setup.
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duec to a typo, mv88e6390_serdes_irq_setup() calls itself, rather than
mv88e6390x_serdes_irq_setup(). It then blows the stack, and shortly
after the machine blows up.
Fixes: 2defda1f4b ("net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In RGMII mode we should not have any delay in port MAC, so disable
the delay.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.
Also fix up the related struct device_node leaks.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org> # 4.19: 36156f9241
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform-device driver data is set on successful probe and will
never be NULL on remove (or we have much bigger problems).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.
Also fix up the related struct device_node leaks.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable <stable@vger.kernel.org> # 4.20
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable and deregister the switch on late probe errors to
avoid use-after-free when the device-resource-managed switch is freed.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable <stable@vger.kernel.org> # 4.20
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses GPIO descriptors only, <linux/of_gpio.h>
is not used so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not use the old GPIO includes so drop
them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's
return their error codes upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports. In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60. Port 6 is the host port.
Setting a zero value can be used to stop port from receiving.
However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate. This does not apply to
multicast and broadcast addresses though. To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.
Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to handle optional reset GPIO in the KSZ switch driver. The switch
has a reset GPIO line which can be controlled by the CPU, so make sure it is
configured correctly in such setups.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ksz_9477_reg.h to ksz9477_reg.h for consistency as the product
name is always KSZ####.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break KSZ9477 DSA driver into two files in preparation to add more KSZ
switch drivers.
Add common functions in ksz_common.h so that other KSZ switch drivers
can access code in ksz_common.c.
Add ksz_spi.h for common functions used by KSZ switch SPI drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ksz_spi.c to ksz9477_spi.c and update Kconfig in preparation to add
more KSZ switch drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename some functions with ksz9477 prefix to separate chip specific code
from common code.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up code according to patch check suggestions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace license with GPL.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.
Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.
This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize mutex before use. Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.
On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c499696e79 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e79 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:
b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'
Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.
Fixes: 7a8c7f5c30 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, make the driver depend on this config option.
User mode Linux does not have CONFIG_HAS_IOMEM set and the driver was
failing on this architecture.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In both 802.3z and SGMII modes we need to configure the MAC accordingly
to flip between Fiber and SGMII modes, and we need to read the MAC
status from the SGMII in-band control word.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18,
fix that offset so we access the correct registers. This would make us
not access the correct SerDes Digital control words, status would be
fine and so we would not be correctly flipping between Fiber and SGMII
modes resulting in incorrect status words being pulled into the SerDes
digital status register.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLINK takes care of filing the right information into
state->an_enabled, get rid of the read from the SerDes's BMCR register.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one code block when returning because the interface type is
unsupported and also check if some unsupported port gets configured.
In addition fix a double the and use dsa_is_cpu_port() instated of
manually getting the CPU port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value from of_reset_control_array_get_exclusive() is not
checked correctly. The test is done against a wrong variable. This
patch fix it.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a cut/paste error and a typo which results in ATU miss violations
not being reported.
Fixes: 0977644c50 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Device Tree is not providing the per-port interrupts, do not fail
during b53_srab_irq_enable() but instead bail out gracefully. The SRAB driver
is used on the BCM5301X (Northstar) platforms which do not yet have the SRAB
interrupts wired up.
Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.
The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.
The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6xxx can have external PHYs attached to certain ports and those
PHYs could even be on different MDIO bus than the one within the switch.
This patch makes sure that ports with such PHYs are configured correctly
according to the information provided by the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Built-in PHY ports are still being polled, avoid generating spurious
and duplicate events which the PHY library resolves through polling
anyways.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "pause" variable is only initialized on BCM5301x.
Fixes: 5e004460f8 ("net: dsa: b53: Add helper to set link parameters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case B53_SRAB is enabled, but not B53_SERDES, we can get the
following linking error:
ERROR: "b53_serdes_init" [drivers/net/dsa/b53/b53_srab.ko] undefined!
We also need to ifdef the body of b53_srab_serdes_map_lane() since it
would not be used when B53_SERDES is disabled and that would produce a
warning.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Northstar Plus SerDes which is accessed through a
special page of the switch. Since this is something that most people
probably will not want to use, make it a configurable option with a
default on ARCH_BCM_NSP where it is the most useful currently.
The SerDes supports both SGMII and 1000baseX modes for both lanes, and
2500baseX for one of the lanes, and is internally looking like a
seemingly standard MII PHY, except for the few bits that got repurposed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHYLINK, things are reasonably straight forward since we
do not yet support SerDes interfaces, that leaves us with just
MLO_AN_PHY and MLO_AN_FIXED to deal with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the logic from b53_adjust_link() responsible for overriding a
given port's link, speed, duplex and pause settings and make two helper
functions to set the port's configuration and the port's link settings.
We will make use of both, as separate functions while adding PHYLINK
support next.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB driver to manage per-port interrupts. Since we cannot
sleep during b53_io_ops, schedule a workqueue whenever we get a port
specific interrupt. We will later make use of this to call back into
PHYLINK when there is e.g: a link state change.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches expose individual interrupt line(s) for port specific
event(s), allow configuring these interrupts at an appropriate time
during port_enable/disable callbacks where all port specific resources
are known to be set-up and ready for use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family has one SERDES interface, which can be used by either
port 4 or port 5. Add interrupt support for the SERDES interface, and
report when the link status changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing to the needed page, actually write the value to the
register!
Fixes: 09cb7dfd3f ("net: dsa: mv88e6xxx: describe PHY page and SerDes")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SRAB driver is the default way to communicate with the integrated
switch on iProc platforms and the MMAP driver is the way to communicate
with the integrated switch on DSL BCM63xx and CM BCM33xx.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards the interrupt can be shared between multiple devices.
For example on Turris Mox the interrupt is shared between all switches.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz9477 is superset of ksz9xx series, driver just works
out of the box for ksz9897 chip with this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added a new error path, but we need to drop the lock before we return.
Fixes: 2d2e1dd299 ("net: dsa: mv88e6xxx: Cache the port cmode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to test if these flags are set but there are some && vs &
typos.
Fixes: efd1ba6af9 ("net: dsa: mv88e6xxx: Add SERDES phydev_mac_change up for 6390")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The totally undocumented IO mode needs to be set to enumerator
0 to enable port 4 also known as WAN in most configurations,
for ordinary traffic. The 3 bits in the register come up as
010 after reset, but need to be set to 000.
The Realtek source code contains a name for these bits, but
no explanation of what the 8 different IO modes may be.
Set it to zero for the time being and drop a comment so
people know what is going on if they run into trouble. This
"mode zero" works fine with the D-Link DIR-685 with
RTL8366RB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port changes CMODE, the SERDES interface being used can change.
Disable interrupts for the old SERDES interface, and enable interrupts
on the new.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
