When a HDCP authentication is in progress, if the display sink is
hot unplugged, all DDC/AUX transaction related to the HDCP
authentication will fail.
This patch moves those kind of HDCP DDC/AUX failures into the debug
logs instead of errors.
v2:
Bksv invalid state is provided as debug msg
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540291288-22185-1-git-send-email-ramalingam.c@intel.com
HDCP check link is invoked only on CP_IRQ detection, instead of all
short pulses.
v3:
No Changes.
v4:
Added sean in cc and collected the reviewed-by received.
v5:
No Change.
v6:
No Change.
v7:
No Change.
v8:
Rebased.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540286550-20399-3-git-send-email-ramalingam.c@intel.com
Just sorting this "if" block from newer to older platform.
The main difference here is the addition of a
missing case with return false that should never occur.
And if it occurs it is better than to raise a warn
than use the icl one.
The gen >= 11 was already present in the previous logic,
although hidden.
So, in summary no real functional change.
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022171526.15641-3-rodrigo.vivi@intel.com
Since when it was introduced we forgot to add
this case so ICL was using a wrong signal_levels
as reference.
Fixes: fb5c8e9d43 ("drm/i915/icl: Implement voltage swing programming sequence for Combo PHY DDI")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181017215652.26841-1-rodrigo.vivi@intel.com
Another user of crtc->config gone. The functions it calls also
needed crtc->config, so convert those as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Still pass m_n struct to intel_pch_transcoder_set_m_n (Ville)]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181011100457.8776-3-maarten.lankhorst@linux.intel.com
LSPCON chips can generate YCBCR outputs, if asked nicely :).
In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes
Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes
So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.
V2: rebase
V3: Addressed review comments from Ville
- add enum crtc_output_format instead of bool ycbcr420
- use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
cases in this way we will have YCBCR 4:4:4 framework ready (except
the ABI part)
V4: Added r-b from Maarten (for v3)
Addressed review comments from Ville:
- Do not add a non-atomic state variable to determine lspcon output.
Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
- Change the state bool name from external scaling to something more
relavent.
- Keep the info and adjusted_mode structures const.
- use crtc_state instead of pipe_config.
- Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase
PS: Ignored following warnings to match the current formatting:
drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
-:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
+#define TRANS_MSA_SAMPLING_444 (2<<1)
^
-:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
+#define TRANS_MSA_CLRSP_YCBCR (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com
This patch adds an enum "intel_output_format" to represent
the output format of a particular CRTC. This enum will be
used to produce a RGB/YCBCR4:4:4/YCBCR4:2:0 output format
during the atomic modeset calculations.
V5:
- Created this separate patch to introduce and init output_format.
- Initialize parameters of output_format_str respectively (Jani N).
- Call it intel_output_format than crtc_output_format(Ville).
- Set output format in pipe_config for every encoder (Ville).
- Get rid of extra DRM_DEBUG_KMS during get_pipe_config (Ville)
V6: Rebase
V7: Fixed alignment warnings (checkpatch)
V8: Another check[atch warning for alignment
V9: Rebase
V10: Rebase on top of DSI restructure
V11: Addressed review comment from Ville
- Set CRTC format for pre-HSW get_pipe_config() function too.
Added Ville's R-B
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-1-git-send-email-shashank.sharma@intel.com
This patch fixes the original commit c0cfb10d9e ("drm/i915/edp:
Do not do link training fallback or prune modes on EDP") that causes
a blank screen in case of certain eDP panels (Eg: seen on Dell XPS13 9350)
where first link training fails and a retraining is required by falling
back to lower link rate/lane count.
In case of some panels they advertise higher link rate/lane count
than whats required for supporting the panel's native mode.
But we always link train at highest link rate/lane count for eDP
and if that fails we can still fallback to lower link rate/lane count
as long as the fallback link BW still fits the native mode to avoid
pruning the panel's native mode yet retraining at fallback values
to recover from a blank screen.
v3:
* Add const for fixed_mode (Ville)
v2:
* Send uevent if link failure on eDP unconditionally
Fixes: c0cfb10d9e ("drm/i915/edp: Do not do link training fallback or prune modes on EDP")
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.17+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107489
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105338
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Alexander Wilson <alexander.wilson@ncf.edu>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009212804.702-1-manasi.d.navare@intel.com
Almost all of the connector destroy functions do the same thing. The
differences are in the edid, detect_edid and panel cleanups, but those
are safely NULL when not initialized. Roll out a common connector
destroy hook.
Inspired by commit bc3213c444 ("drm/i915: Drop the eDP check from
intel_dp_connector_destroy()").
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009141103.20387-1-jani.nikula@intel.com
As long as the connector was zeroed during allocation calling
intel_panel_fini() is safe even if we haven't initialized
the panel struct explicitly. So let's drop the useless eDP
check from dp connector destruction.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181008134641.24868-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Always print out the information whether the port and sink can each
do MST. And let's include the modparam in the debug output as well.
Makes life a little less confusing when you don't have to wonder
why MST isn't kicking in.
This does cause a slight change in our behaviour towards the sink.
Previously we only read the MSTM_CAP register after passing all
the other checks. Now we will read that register regardless. Hopefully
some crazy sink doesn't get confused by a simple register read.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003184210.1306-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
We've opted to use the maximum link rate and lane count for eDP panels,
because typically the maximum supported configuration reported by the
panel has matched the native resolution requirements of the panel, and
optimizing the link has lead to problems.
With eDP 1.4 rate select method and DSC features, this is decreasingly
the case. There's a need to optimize the link parameters. Moreover,
already eDP 1.3 states fast link with fewer lanes is preferred over the
wide and slow. (Wide and slow should still be more reliable for longer
cable lengths.)
Additionally, there have been reports of panels failing on arbitrary
link configurations, although arguably all configurations they claim to
support should work.
Optimize eDP 1.4+ link config fast and narrow.
Side note: The implementation has a near duplicate of the link config
function, with just the two inner for loops turned inside out. Perhaps
there'd be a way to make this, say, more table driven to reduce the
duplication, but seems like that would lead to duplication in the table
generation. We'll also have to see how the link config optimization for
DSC turns out.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: "Lee, Shawn C" <shawn.c.lee@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105267
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905095321.13843-1-jani.nikula@intel.com
There are two copies of the same code called from long and short
pulse handlers.
v2: Rebase due to s/int status/enum drm_connector_status in
intel_dp_detect()
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-6-dhinakaran.pandiyan@intel.com
The intel_dp->detect_done flag is no more useful. Pull
intel_dp_long_pulse() into the lone caller,
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-5-dhinakaran.pandiyan@intel.com
A crtc modeset lock was added for link retraining but
intel_dp_retrain_link() knows to take the necessary locks since
commit c85d200e83 ("drm/i915: Move SST DP link retraining into the
->post_hotplug() hook")
v2: Drop AUX power domain reference in the early return path
Fixes: c85d200e83 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-4-dhinakaran.pandiyan@intel.com
We have two cases of intel_dp to intel_encoder conversions, use a
local variable to store the conversion.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-3-dhinakaran.pandiyan@intel.com
Commit '3cf71bc9904d ("drm/i915: Re-apply "Perform link quality check,
unconditionally during long pulse"")' applies a work around for sinks
that don't signal link loss. The work around does not need to have to be
that broad as the issue was seen with only one particular monitor; limit
this only for external displays as eDP features like PSR turn off the link
and the driver ends up retraining the link seeeing that link is not
synchronized.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-2-dhinakaran.pandiyan@intel.com
Comment claims link needs to be retrained because the connected sink raised
a long pulse to indicate link loss. If the sink did so,
intel_dp_hotplug() would have handled link retraining. Looking at the
logs in Bugzilla referenced in commit '3cf71bc9904d ("drm/i915: Re-apply
Perform link quality check, unconditionally during long pulse"")', the
issue is that the sink does not trigger an interrupt. What we want is
->detect() from user space to check link status and retrain. Ville's
review for the original patch also indicates the same root cause. So,
rewrite the comment.
v2: Patch split and rewrote comment.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jan-Marek Glogowski <glogow@fbihome.de>
References: 3cf71bc990 ("drm/i915: Re-apply "Perform link quality check, unconditionally during long pulse"")
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927205735.16651-1-dhinakaran.pandiyan@intel.com
So far we have only been calling
drm_connector_init_panel_orientation_property(), which checks for
panel orientation quirks in the drm_panel_orientation_quirks.c file,
for DSI panels as so far only devices with DSI panels have had panels
which are not mounted up right.
The new GPD win2 device uses a portrait screen in a landscape case,
so now we've a device with an eDP panel which needs the panel-orientation
property to let the fbcon code and userspace know that the image needs to
be fixed-up.
This commit makes intel_edp_init_connector() call
drm_connector_init_panel_orientation_property() so that the property
gets added.
Reported-and-tested-by: russianneuromancer@ya.ru
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180909133457.10636-2-hdegoede@redhat.com
UAPI Changes:
- None
Cross-subsystem Changes:
- None
Core Changes:
- Allow drivers to disable features with per-device granularity (Ville)
- Use EOPNOTSUPP when iface/feature is unsupported instead of
EINVAL/errno soup (Chris)
- Simplify M/N DP quirk by using constant N to limit size of M/N (Shawn)
- add quirk for LG LP140WF6-SPM1 eDP panel (Shawn)
Driver Changes:
- i915/amdgpu: Disable DRIVER_ATOMIC for older/unsupported devices (Ville)
- sun4i: add support for R40 HDMI PHY (Icenowy)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Lee, Shawn C <shawn.c.lee@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAluiqZAACgkQlvcN/ahK
BwrD7gf+O9hI1+sWAKs9/D2xz5G0Ap/wTUtPZprVx+UMg833T4E3q5esSTvlKd5q
QdijWWFZ3Eu7osQB5QTvCHpJ1F1Q9DScYdD5rd0WRhZBGnBd2guFziFRhleXpQH1
CTo/xjS4Y1l1wEildvZdjPaDfXE0Q+uK8kl11AIVoYQvW6V28/pwCW+mmfMfQG4D
lC9Lj5iPTDGLmbT3DZcH9ZUU8CZreJVPDn+mi8XsAOGt55YlCphl5XsOabNRzpCh
5VYZbauJqrlfa3/cbVuFpTqjqR5XRlMvzgdYH2Wa+9JreiReNCDs3CVL4YnLWe0p
PIfE6ZC2ucX831aZOodV7KtwtLYc/Q==
=oPPq
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-09-19' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.20:
UAPI Changes:
- None
Cross-subsystem Changes:
- None
Core Changes:
- Allow drivers to disable features with per-device granularity (Ville)
- Use EOPNOTSUPP when iface/feature is unsupported instead of
EINVAL/errno soup (Chris)
- Simplify M/N DP quirk by using constant N to limit size of M/N (Shawn)
- add quirk for LG LP140WF6-SPM1 eDP panel (Shawn)
Driver Changes:
- i915/amdgpu: Disable DRIVER_ATOMIC for older/unsupported devices (Ville)
- sun4i: add support for R40 HDMI PHY (Icenowy)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180919200218.GA186644@art_vandelay
Some DP dongles in particular seem to be fussy about too large
link M/N values. Set specific value for N divider can resolve
this issue per dongle vendor's comment. So configure N as
constant value (0x8000) to instead of reduce M/N formula when
specific DP dongle connected.
v2: add more comments for issue description and fix typo.
v3: add lost commit messages back for version 2
v4: send patch to both intel-gfx and dri-devel
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1536733371-25004-3-git-send-email-shawn.c.lee@intel.com
This re-applies the workaround for "some DP sinks, [which] are a
little nuts" from commit 1a36147bb9 ("drm/i915: Perform link
quality check unconditionally during long pulse").
It makes the secondary AOC E2460P monitor connected via DP to an
acer Veriton N4640G usable again.
This hunk was dropped in commit c85d200e83 ("drm/i915: Move SST
DP link retraining into the ->post_hotplug() hook")
Fixes: c85d200e83 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
[Cleaned up commit message, added stable cc]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180825191035.3945-1-lyude@redhat.com
Unlike the other ports, TC ports are not available to use as soon as
we get a hotplug. The TC PHYs can be shared between multiple
controllers: display, USB, etc. As a result, handshaking through FIA
is required around connect and disconnect to cleanly transfer
ownership with the controller and set the type-C power state.
This patch implements the flow sequences described by our
specification. We opt to grab ownership of the ports as soon as we get
the hotplugs in order to simplify the interactions and avoid surprises
in the user space side. We may consider changing this in the future,
once we improve our testing capabilities on this area.
v2:
* This unifies the DP and HDMI patches so we can discuss everything
at once so people looking at random single patches can actually
understand the direction.
* I found out the spec was updated a while ago. There's a small
difference in the connect flow and the patch was updated for that.
* Our spec also now gives a good explanation on what is really
happening. As a result, comments were added.
* Add some more comments as requested by Rodrigo (Rodrigo).
v3:
* Downgrade a DRM_ERROR that shouldn't ever happen but we can't act
on in case it does (Chris).
BSpec: 21750, 4250.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801173441.9789-1-paulo.r.zanoni@intel.com
For a TBT sequence, we need to set the IO type to TBT
in DDI_AUX_CTL.
v2: Avoid duplications.(Paulo)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532648115-29795-2-git-send-email-anusha.srivatsa@intel.com
The short pulse handler checks if channel equalization is okay and
goes onto retrain a link if there are active MST links. This retraining
path is not meant for new MST connections, but due to a bug elsewhere, if
active_mst_links is < 0 the boolean check for active_mst_links passes and
we proceed to retrain a new link. This results in a sequence of failed link
training attempts, most likely due to the hardware not setup for link
training at that point i.e., missing the DDI pre_enable sequence.
[ 80.301272] [drm:intel_dp_check_mst_status] channel EQ not ok, retraining
[ 80.301312] [drm:intel_ddi_prepare_link_retrain] *ERROR* Timeout waiting for DDI BUF C idle bit
The above error gives us a hint something went wrong before link
training started.
Check for a positive value of active_mst_links and throw in a warning for
invalid active_mst_links as debug aid.
Cc: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Tested-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718171943.3246-1-dhinakaran.pandiyan@intel.com
The Gen11 TypeC PHY DDI Buffer chapter, PHY Clock Gating Programming
section says that PHY clock gating should be disabled before starting
voltage swing programming, then enabled after any link training is
complete.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-6-paulo.r.zanoni@intel.com
Programming this register is part of the Enable Sequence for
DisplayPort on ICL. Do as the spec says.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-5-paulo.r.zanoni@intel.com
In ICL, Flexible IO Adapter (FIA) muxes data and clocks of USB 3.1,
tbt and display controller. In DP alt mode FIA configure the
number of lanes and will be used apart from DPCD read to calculate max
available lanes for DP enablement.
v2 (from Paulo): Simple rebase.
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com> (v1).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[Paulo: significant rewrite of the patch.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-4-paulo.r.zanoni@intel.com
The type is detected based on the live status bits. Once detected,
it's not supposed to be changed, so we have some sanity checks for
that.
v2: Rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-3-paulo.r.zanoni@intel.com
Do like the other functions and check for the status bits. The "Hot
Plug Detection" page from our documentation says we can't just use the
ISR bits on the CPU side (North Display, which has the TC and TBT
modes), so use the correct register: DFLEXDPSP, TC Live State field.
v2: Rebase.
v3:
- Simplify true/false assignment (Rodrigo).
- Reorganize is_gen if ladder (Rodrigo).
- Don't use the ISR for TC/TBT CPU bits.
v4:
- Improve commit message wording (Lucas).
v5:
- COMMIT_LOG_LONG_LINE (Checkpatch).
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> (v3).
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725195927.12059-1-paulo.r.zanoni@intel.com
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
-----BEGIN PGP SIGNATURE-----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=HyBh
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-07-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.19:
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718200826.GA20165@juma
It was originally introduced following the VESA spec in order to validate PSR.
However we found so many issues around sink_crc that instead of helping PSR
development it only brought another layer of trouble to the table.
So, sink_crc has been a black whole for us in question of time, effort and hope.
First of the problems is that HW statement is clear: "Do not attempt to use
aux communication with PSR enabled". So the main reason behind sink_crc is
already compromised.
For a while we had hope on the aux-mutex could workaround this problem on SKL+
platforms, but that mutex was not reliable, not tested,
and we shouldn't use according to HW engineers.
Also, nor source, nor sink designed and implemented the sink_crc to be used like
we are trying to use here.
Well, the sink side of things is also apparently not prepared for this
case. Each panel that we tried seemed to have a different behavior with same
code and same source.
So, for all the time we lost on trying to ducktape all these different issues
I believe it is now time to move PSR to a more reliable validation.
Maybe not a perfect one as we dreamed for this sink_crc, but at least more
reliable.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705192528.30515-1-rodrigo.vivi@intel.com
Since there's very few callers of these I've decided to do them all in
one patch. With this the unecessarily long drm_mode_connector_ prefix
is gone from the codebase! The only exception being struct
drm_mode_connector_set_property, which is part of the uapi so can't be
renamed.
Again done with sed+some manual fixups for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-8-daniel.vetter@ffwll.ch
Instead of looping over ports and hpd_pins, let's loop over
the encoders when doing hotplug processing. And instead of
depending on dev_priv->irq_port[] to tell us whether the
encoder has the ->hpd_pulse() hook or not, we can just
check for that directly. So we can just nuke irq_port[] entirely.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-5-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Rather than looping over all the ports and picking the encoder based on
the port, let's just loop over all the encoders instead. Gets rid of
some irq_port[] usage, which is a bit of an eye sore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705164357.28512-4-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
eDP spec states that sink device will do a short pulse in HPD
line when there is a PSR/PSR2 error that needs to be handled by
source, this is handling the first and most simples error:
DP_PSR_SINK_INTERNAL_ERROR.
Here taking the safest approach and disabling PSR(at least until
the next modeset), to avoid multiple rendering issues due to
bad pannels.
v5:
added lockdep_assert in psr_disable and renamed psr_disable()
to intel_psr_disable_locked()
v4:
Using CAN_PSR instead of HAS_PSR in intel_psr_short_pulse
v3:
disabling PSR instead of exiting on error
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626201644.21932-2-jose.souza@intel.com
This became dead code with commit 309bd8ed46 ("drm/i915: Reinstate
GMBUS and AUX interrupts on gen4/g4x").
v2: Move comment about HW behavior to where decision is made to enable
MSI (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180523180435.18042-1-lucas.demarchi@intel.com
DP spec 1.4 supports training pattern set 4 (TPS4) for HBR3 link
rate. This will be used in link training's channel equalization
phase if supported by both source and sink.
This patch adds the helpers to check if HBR3 is supported and uses
TPS4 in training pattern selection during link training.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611222655.5696-2-paulo.r.zanoni@intel.com
While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.
We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.
Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe26 ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.
v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180613160553.11664-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.
Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.
To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.
Cc: stable@vger.kernel.org
Cc: Vito Caputo <vcaputo@pengaru.com>
Reported-by: Vito Caputo <vcaputo@pengaru.com>
Fixes: e995ca0b81 ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Add support for DP_AUX_E. Here we also introduce the bits for the AUX
power well E, however ICL power well support is still not enabled yet,
so the power well is not used.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-2-paulo.r.zanoni@intel.com
By moving the check from psr_compute_config() to psr_init_dpcd(), we get
to set the dev_priv->psr.sink_support flag only when the panel is
capable of changing power state. An additional benefit is that the check
will be performed only at init time instead of every atomic_check.
This should change the psr_basic IGT failures on HSW to skips.
v2: Return early when SET_POWER_CAPABLE bit is 0 (Jose)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106217
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106346
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180511195145.3829-2-dhinakaran.pandiyan@intel.com
The power sequencer has bits to allow DP C to be used for eDP.
Currently we assume this will never happen, but I guess it could
theoretically be a thing. Make the code do the right thing in that
case, and toss in a MISSING_CASE() for any other port.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518152931.13104-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Clean up the DP pipe select bits. To make the whole situation a bit
less ugly we'll start to share the same code between .get_hw_state(),
the port state asserts, and the VLV power sequencer code.
v2: Return PIPE_A for cpt/ppt when the port isn't selected by
any transcoder. Returning INVALID_PIPE explodes *somewhere*
on some machines (can't immediately see where though). This
now matches the old behaviour.
v3: Order the defines shift,mask,value (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518152931.13104-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit dc911f5bd8.
Per the report, no matter what display mode you select with xrandr, the
i915 driver will always select the alternate fixed mode. For the
reporter this means that the display will always run at 40Hz which is
quite annoying. This may be due to the mode comparison.
But there are some other potential issues. The choice of alt_fixed_mode
seems dubious. It's the first non-preferred mode, but there are no
guarantees that the only difference would be refresh rate. Similarly,
there may be more than one preferred mode in the probed modes list, and
the commit changes the preferred mode selection to choose the last one
on the list instead of the first.
(Note that the probed modes list is the raw, unfiltered, unsorted list
of modes from drm_add_edid_modes(), not the pretty result after a
drm_helper_probe_single_connector_modes() call.)
Finally, we already have eerily similar code in place to find the
downclock mode for DRRS that seems like could be reused here.
Back to the drawing board.
Note: This is a hand-crafted revert due to conflicts. If it fails to
backport, please just try reverting the original commit directly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105469
Reported-by: Rune Petersen <rune@megahurts.dk>
Reported-by: Mark Spencer <n7u4722r35@ynzlx.anonbox.net>
Fixes: dc911f5bd8 ("drm/i915/edp: Allow alternate fixed mode for eDP if available.")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516080110.22770-1-jani.nikula@intel.com
Almost all of the GEN7 checks in the DP code are actually looking for
IVB. HSW doesn't even take these codepaths, and VLV is excluded on
account of not having port A. So let's change the checks to IS_IVB to
make the code less confusing.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-3-ville.syrjala@linux.intel.com
All DDI platforms support the full set of preemph settings for each
supported vswing, so let's use the same code for them. We'll also move
the code into intel_ddi.c so that it sits closer to the actual buf trans
tables.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Use intel_ddi_dp_voltage_max() for HSW/BDW too instead of letting these
fall through the if ladder in a weird way. This function will look at
the actual buf trans tables we have for HSW/BDW to determine the max
vswing level.
It looks to me like the current code leads HSW port A down the IVB port
A path, HSW port B+ and BDW fall through to the very end. Both cases do
result in the correct max vswing level 2, but it's very hard to see that
from the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517170309.28630-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
On intel_dp_compute_config() we were calculating the needed vco
for eDP on gen9 and we stashing it in
intel_atomic_state.cdclk.logical.vco
However few moments later on intel_modeset_checks() we fully
replace entire intel_atomic_state.cdclk.logical with
dev_priv->cdclk.logical fully overwriting the logical desired
vco for eDP on gen9.
So, with wrong VCO value we end up with wrong desired cdclk, but
also it will raise a lot of WARNs: On gen9, when we read
CDCLK_CTL to verify if we configured properly the desired
frequency the CD Frequency Select bits [27:26] == 10b can mean
337.5 or 308.57 MHz depending on the VCO. So if we have wrong
VCO value stashed we will believe the frequency selection didn't
stick and start to raise WARNs of cdclk mismatch.
[ 42.857519] [drm:intel_dump_cdclk_state [i915]] Changing CDCLK to 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 42.897269] cdclk state doesn't match!
[ 42.901052] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[ 42.938004] RIP: 0010:intel_set_cdclk+0x5d/0x110 [i915]
[ 43.155253] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[ 43.170277] [drm:intel_dump_cdclk_state [i915]] [hw state] 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 43.182566] [drm:intel_dump_cdclk_state [i915]] [sw state] 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
v2: Move the entire eDP's vco logical adjustment to inside
the skl_modeset_calc_cdclk as suggested by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: bb0f4aab0e ("drm/i915: Track full cdclk state for the logical and actual cdclk frequencies")
Cc: <stable@vger.kernel.org> # v4.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20180502175255.5344-1-rodrigo.vivi@intel.com
For now, there's just the one link config selection, optimizing for slow
and wide link. No functional changes.
Keep the debug logging in the caller, to avoid duplication later on if
alternative link confing selection gets added.
v2: Improved commit message
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64848b76bf90d6ceecd7ec6b5add28531e0b1a41.1524730974.git.jani.nikula@intel.com
We call intel_dp_compute_rate() in intel_dp_compute_config() only to be
able to debug log the link_bw and rate_select parameters; we don't use
the parameters here for anything else. We call intel_dp_compute_rate()
again during link training where we actually need and use the
parameters.
Move the debug logging of link_bw and rate_select to
intel_dp_link_training_clock_recovery(), and clean up the extra
intel_dp_compute_rate() call and extra clutter from the already
overcrowded intel_dp_compute_config().
v2: Rewrote commit message (Rodrigo, Manasi)
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c5cf6a179e2d244eceb6bb80a792765d9efbee4f.1524730974.git.jani.nikula@intel.com
AFAIK CHV was supposed to have HBR2 originally, but in the end the feature
was dropped. We still have some code leftovers from those early days.
Eliminate them.
The extra bit for the training pattern seems to be dead in the hardware.
I can set it (in fact I can set almost any reserved bit in the
registers) but it doesn't seem to interfere with the operation of the
hardware. Either that or I'm very lucky that my displays complete link
training with the incorrect pattern being sent out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302095656.19662-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
LSPCON likes to throw short HPDs during the enable seqeunce prior to the
link being trained. These obviously result in the channel CR/EQ check
failing and thus we schedule a pointless hotplug work to retrain the
link. Avoid that by ignoring the bad CR/EQ status until we've actually
initially trained the link.
I've not actually investigated to see what LSPCON is trying to signal
with the short pulse. But as long as it signals anything I think we're
supposed to check the link status anyway, so I don't really see other
good ways to solve this. I've not seen these short pulses being
generated by normal DP sinks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-5-ville.syrjala@linux.intel.com
Doing link retraining from the short pulse handler is problematic since
that might introduce deadlocks with MST sideband processing. Currently
we don't retrain MST links from this code, but we want to change that.
So better to move the entire thing to the hotplug work. We can utilize
the new encoder->hotplug() hook for this.
The only thing we leave in the short pulse handler is the link status
check. That one still depends on the link parameters stored under
intel_dp, so no locking around that but races should be mostly harmless
as the actual retraining code will recheck the link state if we
end up there by mistake.
v2: Rebase due to ->post_hotplug() now being just ->hotplug()
Check the connector type to figure out if we should do
the HDMI thing or the DP think for DDI
[pushed with whitespace changes for sparse]
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-3-ville.syrjala@linux.intel.com
The LG 4k TV I have doesn't deassert HPD when I turn the TV off, but
when I turn it back on it will pulse the HPD line. By that time it has
forgotten everything we told it about scrambling and the clock ratio.
Hence if we want to get a picture out if it again we have to tell it
whether we're currently sending scrambled data or not. Implement
that via the encoder->hotplug() hook.
v2: Force a full modeset to not follow the HDMI 2.0 spec more
closely (Shashank)
[pushed with whitespace fixes to make sparse happy]
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117192149.17760-1-ville.syrjala@linux.intel.com
We have two instances of the code to fill out the header for the aux
message. Pull it into a small helper.
v2: Rebase due to txbuf[] changes
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222212802.4826-1-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Let's try to keep the details on the AKSV stuff concentrated
in one place. So move the control bit and +5 data size handling
there.
v2: Increase txbuf[] to include the payload which intel_dp_aux_xfer()
will still load into the registers even though the hardware
will ignore it
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222212732.4665-1-ville.syrjala@linux.intel.com
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
To pull in the HDCP changes, especially wait_for changes to drm/i915
that Chris wants to build on top of.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
dp_rates[] array is a superset of all the link rates supported
by sink devices. DP 1.3 specification adds HBR3 (8.1Gbps) link rate
to the set of link rates supported by sink. This patch adds this rate
to dp_rates[] array that gets used to populate the sink_rates[]
array limited by max rate obtained from DP_MAX_LINK_RATE DPCD register.
v2:
* Rebased on top of Jani's localized rates patch
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519857110-26916-1-git-send-email-manasi.d.navare@intel.com
Driver Changes:
- Lift alpha_support protection from Cannonlake (Rodrigo)
* Meaning the driver should mostly work for the hardware we had
at our disposal when testing
* Used to be preliminary_hw_support
- Add missing Cannonlake PCI device ID of 0x5A4C (Rodrigo)
- Cannonlake port register fix (Mahesh)
- Fix Dell Venue 8 Pro black screen after modeset (Hans)
- Fix for always returning zero out-fence from execbuf (Daniele)
- Fix HDMI audio when no no relevant video output is active (Jani)
- Fix memleak of VBT data on driver_unload (Hans)
- Fix for KASAN found locking issue (Maarten)
- RCU barrier consolidation to improve igt/gem_sync/idle (Chris)
- Optimizations to IRQ handlers (Chris)
- vblank tracking improvements (64-bit resolution, PM) (Dhinakaran)
- Pipe select bit corrections (Ville)
- Reduce runtime computed device_info fields (Chris)
- Tune down some WARN_ONs to GEM_BUG_ON now that CI has good coverage (Chris)
- A bunch of kerneldoc warning fixes (Chris)
* tag 'drm-intel-next-2018-02-21' of git://anongit.freedesktop.org/drm/drm-intel: (113 commits)
drm/i915: Update DRIVER_DATE to 20180221
drm/i915/fbc: Use PLANE_HAS_FENCE to determine if the plane is fenced
drm/i915/fbdev: Use the PLANE_HAS_FENCE flags from the time of pinning
drm/i915: Move the policy for placement of the GGTT vma into the caller
drm/i915: Also check view->type for a normal GGTT view
drm/i915: Drop WaDoubleCursorLP3Latency:ivb
drm/i915: Set the primary plane pipe select bits on gen4
drm/i915: Don't set cursor pipe select bits on g4x+
drm/i915: Assert that we don't overflow frontbuffer tracking bits
drm/i915: Track number of pending freed objects
drm/i915/: Initialise trans_min for skl_compute_transition_wm()
drm/i915: Clear the in-use marker on execbuf failure
drm/i915: Prune gen8_gt_irq_handler
drm/i915: Track GT interrupt handling using the master iir
drm/i915: Remove WARN_ONCE for failing to pm_runtime_if_in_use
drm: intel_dpio_phy: fix kernel-doc comments at nested struct
drm/i915: Release connector iterator on a digital port conflict.
drm/i915/execlists: Remove too early assert
drm/i915: Assert that we always complete a submission to guc/execlists
drm: move read_domains and write_domain into i915
...
Localize link rate arrays by moving them to the functions where they're
used. Further clarify the distinction between source and sink
capabilities. Split pre and post Haswell arrays, and get rid of the
array size arithmetics. Use a direct rate value in the paranoia case of
no common rates find.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227105911.4485-1-jani.nikula@intel.com
While it seems totally unlikely that any system would mix a cpu/north
aux channel with a pch/south port (or vice versa) we should still
consult intel_dp->aux_ch rather than encoder->port when figuring out
which clock is actually used by the aux ch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-5-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #irc
Currently, BXT_PP is hardcoded with value '0'.
It practically disabled eDP backlight on MRB (BXT) platform.
This patch will tell which BXT_PP registers (there are two set of
PP_CONTROL in the spec) to be used as defined in VBT (Video Bios Timing
table) and this will enabled eDP backlight controller on MRB (BXT)
platform.
v2:
- Remove unnecessary information in commit message.
- Assign vbt.backlight.controller to a backlight_controller variable and
return the variable value.
v3:
- Rebased to latest code base.
- updated commit title.
Signed-off-by: Mustamin B Mustaffa <mustamin.b.mustaffa@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180227030734.37901-1-mustamin.b.mustaffa@intel.com
The core already takes care of the delay before retrying. The delay now
changes to (500, 600)us instead of (500 + 1000, 600 + 1500)us.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-5-dhinakaran.pandiyan@intel.com
intel_edp_init_dpcd() is cluttered with PSR specific DPCD checks and
intel_dp.c is huge.
No functional change intended.
v2: Rebased.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-3-dhinakaran.pandiyan@intel.com
The usual if ladder order should be from newest to oldest
platform. However the CNL conditional statement was misplaced.
This patch sets the DP source for platforms starting from the newest
to oldest.
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519701075-9894-1-git-send-email-manasi.d.navare@intel.com
Just store function pointers that give us the correct register offsets
instead of storing the register offsets themselves. Slightly less
efficient perhaps but saves a few bytes and better matches how we do
things elsewhere.
v2: Keep a local array of data registers (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-3-ville.syrjala@linux.intel.com
Since we no longer have a 1:1 correspondence between ports and AUX
channels, let's give AUX channels their own enum. Makes it easier
to tell the apples from the oranges, and we get rid of the
port E AUX power domain FIXME since we now derive the power domain
from the actual AUX CH.
v2: Rebase due to AUX F
v3: Split out the power domain fix (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v2
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v2
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-2-ville.syrjala@linux.intel.com
Select the aux power domain based on the aux ch rather than based on
the port. Now we can rid ourselves of the port E FIXME as well.
v2: Split from the enum aux_ch patch (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> #v1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222181036.15251-1-ville.syrjala@linux.intel.com
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEfxcpfMSgdnQMs+QqlvcN/ahKBwoFAlqDR7wACgkQlvcN/ahK
BwrxxAgAm3HrrSvtfFPooUsVuodl7KxUF9Mc/MzCNkakP3+Gs0PBE6pp+PhpcBT4
7WwkONTvVKgtnhoIzl8k0Xp8TrDZDWFzpDUluug2knr4nHHkksXtimnz9sfyzGHw
s5XofrV8KQe710grKvUry1VtBrlGRGchd+Xjg1bl+BONnwTmJ8c53npa+d6X0nnt
c+qlP7U9ZawIb59eSL98CuaYsH8oQcMya/jUlb96ky+mx4ugHv9J3ePYIZTqqNDq
/YY1xVhlDQx8iKx7yUp8mreHp5tBL/o3hNNmLMnPDx8jwZfKt7R9MZHH+RRhgl71
TZJmZMUmUyUntVV9NVim8GVHMyDcYQ==
=3uTU
-----END PGP SIGNATURE-----
Merge tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Add HDCP support to i915 drm driver.
* tag 'topic/hdcp-2018-02-13' of git://anongit.freedesktop.org/drm/drm-misc: (26 commits)
drm/i915: fix misalignment in HDCP register def
drm/i915: Reauthenticate HDCP on failure
drm/i915: Detect panel's hdcp capability
drm/i915: Optimize HDCP key load
drm/i915: Retry HDCP bksv read
drm/i915: Connector info in HDCP debug msgs
drm/i915: Stop encryption for repeater with no sink
drm/i915: Handle failure from 2nd stage HDCP auth
drm/i915: Downgrade hdcp logs from INFO to DEBUG_KMS
drm/i915: Restore HDCP DRM_INFO when with no downstream
drm/i915: Check for downstream topology errors
drm/i915: Start repeater auth on READY/CP_IRQ
drm/i915: II stage HDCP auth for repeater only
drm/i915: Extending HDCP for HSW, BDW and BXT+
drm/i915/dp: Fix compilation of intel_dp_hdcp_check_link
drm/i915: Only disable HDCP when it's active
drm/i915: Don't allow HDCP on PORT E/F
drm/i915: Implement HDCP for DisplayPort
drm/i915: Implement HDCP for HDMI
drm/i915: Add function to output Aksv over GMBUS
...
While the comment singles out Port A or B, the code says Port A or *D*.
Looking at the history it seems that the comment was added after the code,
so it seems likely that the code is correct, not the comment.
CC: Jani Nikula <jani.nikula@intel.com>
CC: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180209130755.11893-1-david.weinehall@linux.intel.com
DP HDCP1.4 spec mandates that An can be written to panel only after
detecting the panel's hdcp capability.
For DP 0th Bit of Bcaps register indicates the panel's hdcp capability
For HDMI valid BKSV indicates the panel's hdcp capability.
For HDMI it is optional to detect the panel's hdcp capability before
An Write.
v2:
Added comments explaining the need for action [Seanpaul].
Made panel's hdcp capability detection optional for hdmi [Seanpaul].
Defined a func for reading bcaps for DP [Seanpaul].
v3:
Removed the NULL initialization [Seanpaul].
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1517609350-10698-7-git-send-email-ramalingam.c@intel.com
We have the max DP link rate info available in VBT since BDB version
216, included in child device config since commit c4fb60b9ab
("drm/i915/bios: add DP max link rate to VBT child device
struct"). Parse it and use it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a8b1364d1f2394fba3062b6ad11b474744ea4366.1517482774.git.jani.nikula@intel.com
Make the limiting rate based instead of messing with the array size.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cb03b9419191a7d6359bf371aacb2d3725c746de.1517482774.git.jani.nikula@intel.com
