This patch migrates most of the rx producer ring variables to a new
tg3_rx_prodring_set structure and modifies the code accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later patches are going to complicate the ring initialization routines.
This patch breaks out the setup and teardown of the rx producer rings
into separate functions to make the code more readable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch attempts to document the various rx buffer sizes used by the
driver and how they relate to each other.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves where the jumbo capable and msi support flags are
located. This is prep work for the addition of msix support flags.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch separates the code that sets up the mini producer ring from
the code that sets up the jumbo producer rings. The 5717 asic rev
devices do not have a mini ring, but do have a jumbo frame
implementation similar to the 5704 and previous devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes up the NVRAM detection switch statements to conform
to the kernel coding style.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new device ID for those 5785 devices that will only
use 10/100 phys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device firmware uses the MDIO bus during early setup. If the driver
modifies the MDIO bus configuration while it is in use by the firmware,
any number of bad things can happen. This patch delays MDIO setup until
after the firmware posts its magic signature, signifying initialization
is complete.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the bearer_priority to be less than TIPC_MIN_LINK_PRI and greater than
TIPC_MAX_LINK_PRI is logically impossible.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
create_proc_read_entry() is going to be removed soon.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
- no_ether_link : If set to 1, do not use ETHER_LINK
- ether_link_active_low : If set to 1, ETHER_LINK is active low.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On TI's DA850/OMAP-L138 EVM, MAC address is stored in SPI
flash which is accessed using MTD interface.
This patch delays the initialization of DaVinci EMAC driver
by changing module_init to late_initcall. This helps SPI and
MTD drivers to get initialized before EMAC thereby enabling
EMAC driver to read the MAC address while booting and use it.
Tested with NFS on DM644x, DM6467, DA830/OMAP-L137 and
DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the copy of the MD5 authentication key from tcp_check_req().
This key has already been copied by tcp_v4_syn_recv_sock() or
tcp_v6_syn_recv_sock().
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a per-qdisc bitmap for pfifo_fast giving availability
of skbs for each band. This allows faster lookup for a skb when
there are no high priority skbs. Also, it helps in (rare) cases
when there are no skbs on the list, where an immediate lookup is
faster than iterating through the three bands.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a received IPv6 Router Advertisement, the kernel
creates or updates an IPv6 Neighbor Cache entry for the sender --
but presently this does not occur if IPv6 forwarding is enabled
(net.ipv6.conf.*.forwarding = 1), or if IPv6 Router Advertisements
are not accepted (net.ipv6.conf.*.accept_ra = 0), because in these
cases processing of the Router Advertisement has already halted.
This patch allows the Neighbor Cache to be updated in these cases,
while still avoiding any modification to routes or link parameters.
This continues to satisfy RFC 4861, since any entry created in the
Neighbor Cache as the result of a received Router Advertisement is
still placed in the STALE state.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Better small packet receive performance.
- Better handling of Flow control on 5709.
- Fixed iSCSI TMP ABORT TASK problem.
- Added iSCSI TCP timestamp option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition in the time-wait sockets code that can lead
to premature termination of FIN_WAIT2 and, subsequently, to RST
generation when the FIN,ACK from the peer finally arrives:
Time TCP header
0.000000 30755 > http [SYN] Seq=0 Win=2920 Len=0 MSS=1460 TSV=282912 TSER=0
0.000008 http > 30755 aSYN, ACK] Seq=0 Ack=1 Win=2896 Len=0 MSS=1460 TSV=...
0.136899 HEAD /1b.html?n1Lg=v1 HTTP/1.0 [Packet size limited during capture]
0.136934 HTTP/1.0 200 OK [Packet size limited during capture]
0.136945 http > 30755 [FIN, ACK] Seq=187 Ack=207 Win=2690 Len=0 TSV=270521...
0.136974 30755 > http [ACK] Seq=207 Ack=187 Win=2734 Len=0 TSV=283049 TSER=...
0.177983 30755 > http [ACK] Seq=207 Ack=188 Win=2733 Len=0 TSV=283089 TSER=...
0.238618 30755 > http [FIN, ACK] Seq=207 Ack=188 Win=2733 Len=0 TSV=283151...
0.238625 http > 30755 [RST] Seq=188 Win=0 Len=0
Say twdr->slot = 1 and we are running inet_twdr_hangman and in this
instance inet_twdr_do_twkill_work returns 1. At that point we will
mark slot 1 and schedule inet_twdr_twkill_work. We will also make
twdr->slot = 2.
Next, a connection is closed and tcp_time_wait(TCP_FIN_WAIT2, timeo)
is called which will create a new FIN_WAIT2 time-wait socket and will
place it in the last to be reached slot, i.e. twdr->slot = 1.
At this point say inet_twdr_twkill_work will run which will start
destroying the time-wait sockets in slot 1, including the just added
TCP_FIN_WAIT2 one.
To avoid this issue we increment the slot only if all entries in the
slot have been purged.
This change may delay the slots cleanup by a time-wait death row
period but only if the worker thread didn't had the time to run/purge
the current slot in the next period (6 seconds with default sysctl
settings). However, on such a busy system even without this change we
would probably see delays...
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is rework and cleanup of the resize function.
Some bugs we had. We were using ->parent when we should use
node_parent(). Also we used ->parent which is not assigned by
inflate in inflate loop.
Also a fix to set thresholds to power 2 to fit halve
and double strategy.
max_resize is renamed to max_work which better indicates
it's function.
Reaching max_work is not an error, so warning is removed.
max_work only limits amount of work done per resize.
(limits CPU-usage, outstanding memory etc).
The clean-up makes it relatively easy to add fixed sized
root-nodes if we would like to decrease the memory pressure
on routers with large routing tables and dynamic routing.
If we'll need that...
Its been tested with 280k routes.
Work done together with Robert Olsson.
Signed-off-by: Jens Låås <jens.laas@its.uu.se>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
if tunnel parameters have frag_off set to IP_DF, pmtudisc on the ipv4 link
will be performed by deriving the mtu from the ipv4 link and setting the
DF-Flag of the encapsulating IPv4 Header. If fragmentation is needed on the
way, the IPv4 pmtu gets adjusted, the ipv6 package will be resent eventually,
using the new and lower mtu and everyone is happy.
If the frag_off parameter is unset, the mtu for the tunnel will be derived
from the tunnel device or the ipv6 pmtu, which might be higher than the ipv4
pmtu. In that case we must allow the fragmentation of the IPv4 packet because
the IPv6 mtu wouldn't 'learn' from the adjusted IPv4 pmtu, resulting in
frequent icmp_frag_needed and package loss on the IPv6 layer.
This patch allows fragmentation when tunnel was created with parameter
nopmtudisc, like in ipip/gre tunnels.
Signed-off-by: Sascha Hlusiak <contact@saschahlusiak.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing some forwarding benchmarks, I noticed
ip_rt_send_redirect() is rather expensive, even if send_redirects is
false for the device.
Fix is to avoid two atomic ops, we dont really need to take a
reference on in_dev
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce keepalive_probes(tp) helper, and use it, like
keepalive_time_when(tp) and keepalive_intvl_when(tp)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the 10G iSCSI code to reuse the function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like after rename device proc entry is unusable,
because of no ->read_proc or ->proc_fops.
And create_proc_entry() is deprecated.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase module version, and cleanup module info.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simpler to have one place that spins and accounts for delays,
this will also make the last packet be detected faster for more
repeatable timing.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes how the pktgen thread spins/waits between
packets if delay is configured. It uses a high res timer to
wait for time to arrive.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel ktime_t is a nice generic infrastructure for mananging
high resolution times, as is done in pktgen.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If not using delay then no need to update next_tx after
each packet sent. This allows pktgen to send faster especially
on systems with slower clock sources.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle standard (and non-standard) return values in a switch.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_alloc_skb is NUMA node aware.
Also, don't exhaust atomic emergency pool. Don't want pktgen
to cause OOM behaviour.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The if statement to test for "should a new packet be used"
can be simplified.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do some reorganization of transmit logic path:
* move transmit queue full idle to separate routine
* add a cpu_relax()
* eliminate some of the uneeded goto's
* if queue is still stopped, go back to main thread loop.
* don't give up transmitting if quantum is exhausted (be greedy)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the callers were freeing skb after stopping device.
Remove unneeded forward decl.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't force inlining where not needed. Gcc does better job
of deciding to inline local functions.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of minor functions can be written more compactly.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX completions were running in a workqueue queued by the ISR. This
patch moves the processing of TX completions to an existing RSS NAPI
context.
Now each irq vector runs NAPI for one RSS ring and one or more TX
completion rings.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we downshift to MSI/Legacy if we don't get enough vectors for
cpu_count RSS rings plus cpu_count TX completion rings. This patch
allows running MSIX with the vector count that the platform provides.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have three types of RX rings.
1) Default ring - services rx_ring for broadcast/multicast, handles
firmware events, and errors.
2) TX completion ring - handles only outbound completions.
3) RSS ring - handles only inbound completions.
This patch gets rid of the default ring type and moves it's functionality
into the first RSS ring. This makes better use of MSIX vectors since
they are a limited resource on some platforms.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bonding: Have bond_check_dev_link examine netif_running
Some network devices do not call netif_carrier_off when they
are set administratively down. Have the bonding link check function
also inspect the netif_running state. Ignore netif_running if the
bond_check_dev_link function is called with "reporting" set, as in that
case it's inspecting the capabilities of the non-netif_carrier device
driver.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
max_bonds is of type int and cannot be greater than INT_MAX.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding can use compare_ether_addr() in bond_release.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propogate the vlan_features of the slave devices to the bonding
master device, using the same logic as for regular features.
Tested by Or Gerlitz <ogerlitz@voltaire.com>, who also removed
the debug logic from the original test patch.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
