Tracing used the priv pointer as an identifier,
which has the problem that we don't have it in
all code, and also some people say no pointers
should be "leaked" to userspace.
Use the device name instead, it is more useful
anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are only used in the DVM op_mode.
Also move the rfkill debug macros that
depend on them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to copy shadow_reg_enable into
hw_params since it is a pure hardware parameter
that will never change, we can access it from
the config directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As iwl_prepare_card_hw() is idempotent (and
many cards support AMT anyway) there's no
point in calling iwl_prepare_card_hw() only
for AMT capable devices -- call it always
and simplify the code that way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That name better reflects the contents
of the file and the fact that it isn't
related to iwl-ucode.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transport layer should only check the
hardware RF kill status, not impose any
policy or reaction based on it, so move
that out of it into the op_mode.
For now keep the restriction on loading
firmware, that will have to be removed
later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the mutex no longer needs to be
shared, so move it into iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fact that the mutex must be held is an
implementation detail of DVM, but something
has to ensure that no two synchronous cmds
are submitted concurrently. Move the lockdep
assertion into the DVM-specific code, but
also make the transport abort if there are
two concurrently commands.
The assertion is much more useful though as
the transport check can only catch it when
it actually happens, while the assertion
makes sure it can't possibly happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we cannot send any commands when the
uCode is in RF or CT kill, but that will not be
true for all new uCode versions, so we need to
move the check into the uCode specific code.
Also remove the duplicate rfkill check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrappers to send commands from the DVM
op-mode (which essentially consists of the
current driver). This will allow us to move
specific sanity checks there.
Also, this removes iwl_trans_send_cmd_pdu()
since that can now be taken care of in the
DVM-specific wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This file was recently introduced, but then
directly abused -- it contained private data
that shouldn't have been used by anything
but the implementation of firmware requests
and some very core code. Now that it is no
longer accessed by any code but the code in
iwl-drv.c, we can dissolve it.
Also rename the iwl_nic struct to iwl_drv to
better reflect where and how it is used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Through the driver, struct iwl_fw will
store the firmware. Split this out into
a separate file, iwl-fw.h, and make all
other code use it. To do this, also move
the log pointers into it, and remove the
knowledge of "nic" from everything.
Now the op_mode has a fw pointer, and
(unfortunately) for now the shared data
also needs to keep one for the transport
to access dump the error log -- I think
that will move later.
Since I wanted to constify the firmware
pointers, some more changes were needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
uCode loading belongs to the op_mode, as it
is dependent on various things there and the
commands sent during it are specific to it.
Move the prototypes to iwl-agn.h to indicate
this. To make this possible, also move all
the calibration handling (which is op_mode
dependent after all).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On A-MPDU frames, the hardware only reports valid signal strength data for
the last subframe. The driver also mangled rx_stats->rs_rssi using the
ATH_EP_RND macro in a way that may make sense for ANI, but definitely
not for reporting to mac80211.
This patch changes the code to calculate the signal strength from the rssi
directly instead of taking the average value, and flag everything but
the last subframe in an A-MPDU to tell mac80211 to ignore the signal strength
entirely, fixing signal strength fluctuation issues reported by various
users.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process rx status directly instead of separating the completion test from
the actual rx status processing.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way this is implemented (simply storing the last value) is absolutely
worthless for debugging anything, and the same information is also available
through the MAC sample feature, so there's no point in keeping this around.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They're more expensive than some of the other debug options and only used
in very rare situations, so it sometimes makes sense to disable them while
leaving in debugfs support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cold reset is more reliable for getting the hardware out of some specific
stuck states.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch includes:
Configure EMAC PHY clock source (clock from PHY or internal clock).
Do not advertise PHY half duplex capability as APM821XX EMAC does not support half duplex mode.
Add changes to support configuring jumbo frame for APM821XX EMAC.
[ Fix coding style -DaveM ]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default MTU for CAIF HSI was wrongly set to 15 * 4092 bytes.
The patch sets default MTU size to 4096.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing sparse warnings, the 2 functions are only used in same
file. Defining them as static and not exporting them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing functions that are no longer in use, but still exist
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_PORT functions are implemented in port.c, which is part
of mlx4_core, these functions are exported. The functions are in use by
the mlx4_en module (were originally part of mlx4_en).
Their declaration remained in mlx4_en module, moving the declaration to the right location.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac should be written as __be64 the gid. The warning was because
we changed the mac parameter, which is u64, by writing result of cpu_to_be64
into it. Fixing by using new variable of type __be64.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keys used for the hardware RSS topelitz hash are of type __be32
where the values provided by the driver are from array of u32,
this triggered sparse warning on incorrect type in assignment as of different base types.
Since these values are picked randomly,
the fix is to transform the key to __be32 by executing cpu_to_be_32()
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blue flame buffer is defined to be of type void __iomem *
but was passed to mlx4_bf_copy which gets unsigned long * .
This triggered sparse warning on different address spaces,
fix that by changing mlx4_bf_copy first param to be of type void __iomem * .
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings on incompatibility between the endianess of the ctrl_flags
field of struct mlx4_en_priv to the srcrb_flags field of struct
mlx4_wqe_ctrl_seg by changing the former to be __be32 instead of u32.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Localized the pdev->dev, and using dma_map instead of pci_map
There are multiple map/unmap operations on data path,
optimizing those by saving redundant pointer access.
Those places were identified as hot-spots when running kernel profiling
during some benchmarks.
The fixes had most impact when testing packet rate with small packets,
reducing several % from CPU load, and in some case being the difference
between reaching wire speed or being CPU bound.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silence the following warning:
"warn: returning -1 instead of -ENOMEM is sloppy".
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All other Atheros drivers run the AGC gain calibration and DC offset
calibration only after reset. Running them periodically has caused stability
issues on some (primarily AR2315/2413/5413/5414 based) devices, leading to
messages such as:
ath5k phy0: gain calibration timeout (2462MHz)
ath5k phy0: calibration of channel 11 failed
Related bug reports:
https://dev.openwrt.org/ticket/10574https://bugzilla.redhat.com/show_bug.cgi?id=795141
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some calibration types interfere with tx activity, but the queue stop does
not prevent that. In fact, some calibration types need tx activity to properly
function, so stopping the queues for them is counterproductive.
In some tests this patch has been shown to improve stability, especially in
AP or ad-hoc mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Generate a tsf from internal kernel clock. Prepare the path for having
different tsf offsets on each phy. This will be useful for testing
mesh synchronization algorithms.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This doesn't belong into the op_mode, it has
to be in the drv stop flow instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware request is a base driver flow,
it isn't related to any specific mode.
Move the code related to it into the
base driver file iwl-drv.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used from there, so should be in it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This shouldn't be in the op_mode, as it
will later be switchable at runtime.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch "iwlwifi: simplify auth/assoc flow"
caused a serious throughput degradation due
to me forgetting that there are HT settings
in the station table. To restore throughput,
set these parameters correctly when the sta
moves to assoc state.
This patch should probably be merged with
the auth/assoc redesign patch for upstream.
In that case, this paragraph should be added
to the commit log as the third paragraph
(before talking about RXON):
However, as we only get the station HT data
when the station moves into assoc state, we
also need to program this into the device
(and copy it into our database) then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are DVM specific, and shouldn't be
in iwl-shared.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only used in two places in the same file,
no need to be in iwl-shared.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, queue mapping is handled in the
transport. This may change, but until then
the code for it can be close to where it's
used rather than in iwl-shared.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is how the transport passes things
up into higher layers, so it belongs to
the transport API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_queue_inc_wrap/iwl_queue_dec_wrap aren't
shared functions, they are PCI-E specific,
so move them into the appropriate header.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The annotation/documentation is wrong, we call
it in a context that can't sleep.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just make the code easier to read with less indentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct iwl_rx_mem_buffer implementation details
(DMA address, list pointers) that the upper
layers don't need. Introduce iwl_rx_cmd_buffer
that is passed upstream and only contains the
needed data (the page). Additionally, access
this data only via accessor functions, allowing
us to change the implementation in the future.
These accessors are rxb_addr() (as before) and
rxb_steal_page() to take ownership of the data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CMD_WANT_SKB is set for a (synchronous)
command, the response is passed back to the
caller which is then responsible for freeing
it. Make this more abstract with real API,
passing directly the response packet in the
new cmd.resp_pkt member and also introduce
iwl_free_resp() to free the pages -- this
way the upper layers don't have to directly
touch the page implementation.
NOTE: This breaks IDI -- the new code isn't reflected there yet!
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently use the _irqsafe version, but that
isn't recommended together with ieee80211_rx()
as it can cause races. If the device reports
a TX-status and RX in that order then with the
current combination mac80211 might process them
in the other order, which can cause issues with
powersaving clients.
Use ieee80211_tx_status() to avoid this race.
Since we don't want to call it with locks held,
process the frame queues later -- this is fine
as they are on the stack.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new WoWLAN flow into the transport
there no longer is a need for this to be
shared, so move it into priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the WoWLAN suspend flow, instead of accessing
registers directly, ask the transport to do the
required setup at the end of suspend. If the
transport doesn't implement this, don't tell the
stack we support WoWLAN.
When the device suspends w/o WoWLAN, mac80211
will have stopped it already, which has already
called iwl_apm_stop() via stop_hw(). Thus, it
isn't necessary to call it again in pcie_suspend
and we can simply do nothing there.
This unifies the regular and WoWLAN suspend.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in the two branches of the #ifdef
is almost the same so move the common code
outside the #ifdef.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing to the global config structures
is always wrong. To protect against such
mistakes in the future, mark them const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's not really a good idea to write to the
global static configuration. Use the valid
TX/RX antenna information only from the HW
params struct except in the case where the
values from the config are used to override
the values from the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no SKU override, we always just use
it from EEPROM. As such, we can remove it
from the config and use it in hw_param only.
Since iwl_eeprom_check_sku() really needs
to fill it in also rename that to
iwl_eeprom_init_hw_params().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for the per-device debug
level that we expose in debugfs since the
module parameter is writable in sysfs.
At the same time, simplify code by changing
iwl_get_debug_level(shrd) & IWL_DL_ISR)
to
iwl_have_debug_level(IWL_DL_ISR)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With mac80211 now giving us station information
(via the sta_state callback) before auth/assoc
we can get rid of tx_sync by adding the station
early for the case of managed interfaces. Keep
AP mode actions the same for now.
As we now get the BSSID early, we can also get
rid of iwl_reprogram_ap_sta().
We can still optimise the number of RXONs we
send to the device, but that can be done later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason to set EXIT_PENDING when we
start removing the module, as mac80211 will
cleanly shut down the device in this case.
Additionally, there's no point in rejecting
commands to the device when we're cleaning up
as that only leads to unwanted errors from
mac80211 being printed, such as
failed to remove key (...) from hardware (-16)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some data doesn't need protection, some of the
lock places are simply useless, and some data
can be protected with the mutex instead. Thus
the shared lock can be removed by making those
changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The statistics are currently only half-heartedly
locked against concurrent reading & modification
so introduce a lock to really protect them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the transport has its own locking,
there's no need to have the sta_lock in the
shared data. Also, it can be a BH lock as
it's not used from IRQ handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of (ab)using the sta_lock, make the
transport layer lock its own TX queue data
structures with a lock per queue. This also
unifies with the cmd queue lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the powersave related functions we only need
to set a few parameters for the station command
and can otherwise leave it blank -- there's no
need to copy it from the database.
This allows us to not use the sta lock here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the code by returning directly in the
error case and replacing the switch/if with a
single if statement.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we TX, we hold the sta_lock for a long
time, a lot of which isn't needed. Reduce
the time we hold the lock. Note that this
doesn't really change anything as the code
is already under the other spinlock, but it
makes the code easier to read.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The station ID argument to the function
iwlagn_tx_cmd_build_hwcrypto isn't used
so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's only one place using this function, so
move it where it's needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be doing a shift (1 << FLAG_RADIO_DOWN) here before testing
the flag. As luck would have it, this test works almost correctly.
The current code tests for FLAG_RADIO_OFF instead of FLAG_RADIO_DOWN.
#define FLAG_RADIO_OFF 0 /* User disabling of MAC */
#define FLAG_RADIO_DOWN 1 /* ifup/ifdown disabling of MAC */
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we only monitor while associated, the following
can happen:
- we're associated, and the queue stuck check
runs, setting the queue "touch" time to X
- we disassociate, stopping the monitoring,
which leaves the time set to X
- almost 2s later, we associate, and enqueue
a frame
- before the frame is transmitted, we monitor
for stuck queues, and find the time set to
X, although it is now later than X + 2000ms,
so we decide that the queue is stuck and
erroneously restart the device
It happens more with P2P because there we can
go between associated/unassociated frequently.
Cc: stable@vger.kernel.org
Reported-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192ce when used with the RTL8188CE device would start at about
20 Mbps on a 54 Mbps connection, but quickly drop to 1 Mbps. One of the
symptoms is that the AP would need to retransmit each packet 4 of 5 times
before the driver would acknowledge it. Recovery is possible only by
unloading and reloading the driver. This problem was reported at
https://bugzilla.redhat.com/show_bug.cgi?id=770207.
The problem is due to a missing update of the gain setting.
Signed-off-by: Jingjun Wu <jingjun_wu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the possibility of having the mesh point and AP to be operated
simultaneously in one single radio. Previously, mesh point fails to generate the
mesh beacon if virtual AP is created for the same radio.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the signal strength (in dBm only for now) to
frames that are received via nl80211's various
frame APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a bug introduced by commit fe9a2603c, where the priority bits
in the schedule queue field were masked out.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
With runtime PM, if the ethernet cable is disconnected, the device is
transitioned to D3 state to conserve energy. If the system is shutdown
in this state, any register accesses in rtl_shutdown are dropped on
the floor. As the device was programmed by .runtime_suspend() to wake
on link changes, it is thus brought back up as soon as the link recovers.
Resuming every suspended device through the driver core would slow things
down and it is not clear how many devices really need it now.
Original report and D0 transition patch by Sameer Nanda. Patch has been
changed to comply with advices by Rafael J. Wysocki and the PM folks.
Reported-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe of each port, read and log the part number from VPD.
Remove the Falcon-specific board name lookup.
Initial version by Stuart Hodgson <smhodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Generate a test event on each event queue whenever the interface is
brought up, then after 1 second check that we have either handled a
test event or handled another IRQ for each event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
In case all event queues are broken for some reason, this means it
will only take about a second to check them all, rather than up to 32
seconds. This may also speed up testing in the successful case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
IRQ latency can be ridiculously high for various reasons, so our
current timeouts of 100 ms or 10 ms are too short.
Change the IRQ and event tests to use polling loops starting with a
delay of 1 tick and doubling that if necessary up to a maximum total
delay of approximately 1 second.
Raise the loopback packet RX timeout to 1 second.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
RX and TX completions on the same event queue are generally not associated
with the same flows. The inclusion of TX completions in the adaptive IRQ
score is more of a source of noise rather than useful feedback. Therefore,
do not include them in the score, and adjust the default threshold scores
down.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The in-tree driver has never supported Driverlink. The rest of the
comments are rather redundant, but we can usefully state what the
requirements are on the buffer state.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Fix tg3 to use BQL multi queue related netdev interfaces since the
device supports multi queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Reported-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing fancy:
- sent bytes count is notified in the start_xmit path right before
updating the owner bit in the hardware Tx descriptor (E. Dumazet)
- avoid useless tp->dev dereferencing in start_xmit (E. Dumazet)
Use of netdev_reset_queue is favored over proper accounting in
rtl8169_tx_clear_range since the latter would need more work for the
same result (nb: said accounting degenerates to nothing in xmit_frags).
Signed-off-by: Igor Maravic <igorm@etf.rs>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
In 'ql_adapter_initialize'
the first call for 'spin_unlock_irqrestore()' is with hw_flags = 0,
which is as good as 'spin_unlock_irq()' (unconditional interrupt
enabling). If this is intended, then for better performance
'spin_unlock_irqrestore()' can be replaced with 'spin_unlock_irq()'
and 'spin_lock_irqsave()' can be replaced by 'spin_lock_irq()
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new sparse errors introduced in commit 6221217199 (mlx4_en: dont
change mac_header on xmit)
Reported-by: Or Gerlitz <or.gerlitz@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tidying up some debug statements in brcms_c_ampdu_dotxstatus_complete()
that got broken strings to satisfy checkpatch, but the rules changed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As indicated in [1] on netdev mailing list drivers should not block
on the init_module() syscall. This patch defers the actual driver
registration to a workqueue so the init_module() syscall can complete
without delay.
[1] http://article.gmane.org/gmane.linux.network/217729/
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As indicated in [1] on netdev mailing list drivers should not block
on the init_module() syscall. This patch defers the actual driver
registration to a workqueue so the init_module() syscall can complete
without delay.
[1] http://article.gmane.org/gmane.linux.network/217729/
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The module init function of brcmfmac calls init functions for SDIO and
USB doing driver registration. This patch removes terminating the module
init when a driver registration for one host interface fails.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb code defines a structure for counting statistics. However,
it should use the statistics entry provided in brcmf_bus as that is
exposed to the net_device. The usb private statistics counter only
remains with counters for control packets between driver and usb
device.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several fields in this structure are only written once or not used
at all. Remaining two fields have been moved and brcmf_usb_attrib
definition has been removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_usb_up() the variable devinfo was checked for being
a NULL pointer, but this can not happen. Also the check was done
after dereferencing the pointer. This patch removes the check.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Kan Yan <kanyan@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver rtl8192cu is used with the debug level set to 3 or greater,
the result is "sleeping function called from invalid context" due to
an rcu_read_lock() call in the DM refresh routine in driver rtl8192c.
This lock is not necessary as the USB driver does not use the struct
being protected, thus the lock is set only when a PCI interface is
active.
This bug is reported in https://bugzilla.kernel.org/show_bug.cgi?id=42775.
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Cc: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In usb.c, routine _rtl_usb_init_sw() always returns 0, and rtl_usb_probe()
never checks the returned value. Thus we can change _rtl_usb_init_sw() to
a void routine. In addition, remove the underscore at the beginning of the
name of the routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the unlikely event of a misread of the USB end point count, the driver
generates a divide fault. To prevent this, add a check of the value
returned by _rtl_usb_init(). In addition, add some logging to indicate
why the condition occurred.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In mwifiex_drv_change_adhoc_chan() we pass channel to
mwifiex_bss_ioctl_ibss_channel() which sets the high 16 bits. This
works on little endian systems but not on big endian ones. I've changed
mwifiex_drv_change_adhoc_chan() to use a 16 bit variable. This matches
the other functions in the file.
I considered changing mwifiex_change_adhoc_chan() as well but it turns
out that the function isn't implemented so I just removed the
definition.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible to reload driver if insmod has failed due to
missing firmware.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 uses u8 for key indexes and so should rndis_wlan.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use new RNDIS_WLAN_NUM_KEYS for checks in add_wep_key() and add_wpa_key().
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'beacon_period' in 'struct ndis_80211_conf' is __le32 instead of __le16 so
le32_to_cpu must be used instead of le16_to_cpu.
Also correct 'beacon_interval' variables used for passing this value forward
from u16 to u32 and rename those variables 'beacon_period' This is to avoid
confusion because 'beacon_interval' is defined as __le16 at other structure,
'struct ndis_80211_fixed_ies'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we pick a high value for "offset" then it could lead to an integer
overflow and we would get past the check for:
if (offset + len > buflen) { ...
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These variables can never be less than zero because we cap them in
get_device_pmkids(). Let's make them unsigned here because it's simpler
to not have to worry about negative numbers when we read the code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never use the "len" variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If "offset" is negative then we can get past this check:
if (offset > CONTROL_BUFFER_SIZE)
Or if we pick a very high "req_ie_len" then we can get around the check:
if (offset + req_ie_len > CONTROL_BUFFER_SIZE)
I made "resp_ie_len" and "req_ie_len" unsigned. I don't know if it was
intentional that they were signed in the original.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the bcm5354 (Soc with integrated LP-PHY Wifi) with a recent
firmware >= 478.104 it runs out of memory after a very short time in
OpenWrt after doing an active scan or any thing else where packages are
send. This was cased by a gpio misconfiguration, the firmware triggered
the GPIO pins used for buttons on some devices and that caused an other
driver (OpenWrt diag) listening for these buttons irqs to send many
messages to the user space.
This patch fixes the bug for my devices (Asus WL-520GU) and makes it
work with firmware 666.2. Now the firmware just uses LED GPIO pin
number 1 and not the button pins any more.
This is the GPIO Pin layout used on my device, see [0].
GPIO pin layout:
pin# name type
0 power led
1 wlan led
2 reset button
3 ses buttom
This is the nvram configuration output of "nvram show |grep gpio"
related nvram configuration:
wl0gpio2=11
wl0gpio3=11
wl0gpio0=11
wl0gpio1=0x02
reset_gpio=2
[0]: https://dev.openwrt.org/browser/trunk/package/broadcom-diag/src/diag.c
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this does the same thing as the previous code
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
its better to zero initialize the 'valid_phy_rate_idx' array completely
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently if valid SSID list is provided in scan request, driver
performs specific SSID scan otherwise wildcard scan is chosen.
When wpa_supplicant provides valid SSID list followed by
zero-length SSID for wildcard scan, only specific SSID scan is
performed by driver. Actually driver is expected to do both type
of scanning in this case. The patch fixes this issue.
Also, use SSID list pointer provided by stack directly, instead
of copying SSID's to local structure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use struct cfg80211_ssid available in include/net/cfg80211.h
instead of having similar definition in driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1. Driver and firmware do not support 22Mbps and 72Mbps bitrates.
Remove them from the rate table advertised to cfg80211.
2. First 4 rates from mwifiex_rates table are not valid for
5GHz/A band. Set correct bitrate array's index and no of rates for
ieee80211_supported_band for 5GHz band.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so could cause the tx status queue to overflow during longer
periods of time without non-beacon tx. These events are also required
for proper drv_tx_last_beacon handling.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9003 uses a global tx status queue, processing tx status outside of
the regular tx tasklet is dangerous and messes up hardware/software
synchronization of tx status events.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The approach of this change is flawed, as it triggers tx status processing
from more callsites, yet the chips only have one global tx status queue.
Subsequent patches will properly fix the issue that this one tried to address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When authentication type is configured to NL80211_AUTHTYPE_AUTOMATIC,
driver tries to connect using open mode. The association is failed
if AP is configured in shared mode.
This patch adds code to try association using shared mode as well if
open mode association fails.
Now since we returned exact error code in association response handler
(instead of -1), corresponding changes are done in
mwifiex_process_cmdresp().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was broken by the commit 023ca58f1
"iwlwifi: Move the core suspend function to iwl-agn-lib"
where for some reason the code changed while moving,
from
.len[0] = sizeof(*key_data.rsc_tsc),
to
.len[0] = sizeof(key_data.rsc_tsc),
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a flag to indicate we initiated a recovery work
on purpose, in order to avoid triggering BUG() (when
the bug_on_recovery module param was set).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We didn't update the beacon interval on association
(or on a change notification when working as sta),
so the default interval (100ms) was always used.
Update the beacon interval according to the bss_conf
before starting the sta role (on association).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
return EBUSY on scan when there is any role
in ROC (not necessarily the one we are going
to use)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, CHANGE_CHANNEL indication while
associated is considered as roaming attempt.
However, with the new auth/assoc redesign,
we no longer have to handle this case,
so remove it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In some cases, the wrong vif type was set in the
change_interface callback (P2P_CLIENT/P2P_GO instead
of STA/AP)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The sesssion_counter has to be incremented each time
the dev is started (similar to sta role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx currently looks for AP authorization by registering
a netdev notifier and waiting for the IF_OPER_UP notification,
which is quite cumbersome.
Use the newly introduced sta_state callback (waiting
for assoc -> auth notification) instead, in order to
simplify it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement sta_state callback instead of the
sta_add/remove callbacks.
Update the fw regarding peer state and ht caps
only after the station was authorized. Otherwise,
the fw might try establishing BA session before
the sta is authorized.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On disassociation, check only whether the current vif
is idle, instead of checking whether the device is idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
device role is used for scanning and sending packets
before connection. however, since we don't need to
send packets before ibss creation, there is no need
to start the device on idle-off.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix log messages and corrects some typos
Change logging of failure to enable MSI/MSI-X to display device's PCI
address instead of eth%d. Rectify a typo.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the the existing allocation and free operations
so that they can be used individually.
This is to improve code readability, and also to prepare for
possible future changes like better error recovery and more
dynamic configuration (e.g on-the-fly resizing of the rings).
This change represents a straight up relocation of the existing
code into separate routines without changing any of the contained
code itself. Local variables are relocated as necessary.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since all that include/linux/if_ppp.h does is #include <linux/ppp-ioctl.h>,
this replaces the occurrences of #include <linux/if_ppp.h> with
#include <linux/ppp-ioctl.h>.
It also corrects an error in Documentation/networking/l2tp.txt, where
it referenced include/linux/if_ppp.h as the source of some definitions
that are actually now defined in include/linux/if_pppol2tp.h.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the definitions of the ioctls, constants and structures
relating to the ppp_generic interface to userspace out from if_ppp.h
to a new file, ppp-ioctl.h. The new file has my copyright since I
designed and implemented the ppp_generic interface in the late 1990s.
None of the contents of this file comes from the original if_ppp.h
published by Carnegie Mellon University.
Of the remainder of if_ppp.h, only the PPP_MTU definition was being
used, and this replaces the uses of it with PPP_MRU (which is identical).
Therefore, this replaces the entire file with the single line
#include <linux/ppp-ioctl.h>
which clearly doesn't contain any CMU code. Thus I have removed the
CMU copyright notice with its problematic advertising clause, and in
fact since it's only one trivial line I have not added any other
copyright notice.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the copyright notices on the PPP code that I developed
in the late 1990s from being copyright The Australian National
University to copyright Paul Mackerras. I can do this as I have an
acknowledgement in writing from the Head of the Computer Science
Department at ANU (where I worked then) that ANU does not claim any
intellectual property in this code.
While I'm at it, change the copyright notice from BSD-style to
GNU GPL like the rest of the kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRC reset causes the read DMA engine to go into a mode that breaks up
requests into 256 bytes. A PHY reset is required to bring it back to
the normal mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for weak memory model architectures to ensure that the chip will DMA
valid BD data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback on 9K packet fails because the chip has a DMA limit of 4K. The
loopback test logic uses a single BD for simplicity. Fix it by reducing
the jumbo packet size to the DMA limit.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the specific part which handles the PCAN-USB Pro adapter
from PEAK-System Technik (http://www.peak-system.com). The PCAN-USB Pro
adapter is a dual-channel USB 2.0 adapter compliant with CAN specifications
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
