Some x86 microarchitectures fuse a subset of cmp/test/ALU instructions
with branch instructions, and thus perf annotate highlight such valid
pairs as fused.
When annotated with source, perf uses struct disasm_line to contain
either source or instruction line from objdump output. Usually, a C
statement generates multiple instructions which include such
cmp/test/ALU + branch instruction pairs. But in case of assembly
function, each individual assembly source line generate one
instruction.
The 'perf annotate' instruction fusion logic assumes the previous
disasm_line as the previous instruction line, which is wrong because,
for assembly function, previous disasm_line contains source line. And
thus perf fails to highlight valid fused instruction pairs for assembly
functions.
Fix it by searching backward until we find an instruction line and
consider that disasm_line as fused with current branch instruction.
Before:
│ cmpq %rcx, RIP+8(%rsp)
0.00 │ cmp %rcx,0x88(%rsp)
│ je .Lerror_bad_iret <--- Source line
0.14 │ ┌──je b4 <--- Instruction line
│ │movl %ecx, %eax
After:
│ cmpq %rcx, RIP+8(%rsp)
0.00 │ ┌──cmp %rcx,0x88(%rsp)
│ │je .Lerror_bad_iret
0.14 │ ├──je b4
│ │movl %ecx, %eax
Reviewed-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kim Phillips <kim.phillips@amd.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https //lore.kernel.org/r/20210911043854.8373-1-ravi.bangoria@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull devicetree fixes from Rob Herring:
- Revert fw_devlink tracking 'phy-handle' links. This broke at least a
few platforms. A better solution is being worked on.
- Add Samsung UFS binding which fell thru the cracks
- Doc reference fixes from Mauro
- Fix for restricted DMA error handling
* tag 'devicetree-fixes-for-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: arm: Fix Toradex compatible typo
of: restricted dma: Fix condition for rmem init
dt-bindings: arm: mediatek: mmsys: update mediatek,mmsys.yaml reference
dt-bindings: net: dsa: sja1105: update nxp,sja1105.yaml reference
dt-bindings: ufs: Add bindings for Samsung ufs host
Revert "of: property: fw_devlink: Add support for "phy-handle" property"
The TGA boards were based on the DECchip 21030 PCI graphics accelerator
used mainly for alpha, and existed in a TURBOchannel (TC) version for
the DECstation (MIPS) workstations.
However, the config option for the TGA code is a bit confused, and says
depends on FB && (ALPHA || TC)
because people didn't really want to enable the option for random PCI
environments, so the "ALPHA" stands in for that case (while the TC case
is then the MIPS DECstation case).
So that config dependency is kind of a mixture of architecture and bus
choices. But it's incorrect, in that there were non-PCI-based alpha
hardware, and then the driver just causes warnings:
drivers/video/fbdev/tgafb.c:1532:13: error: ‘tgafb_unregister’ defined but not used [-Werror=unused-function]
1532 | static void tgafb_unregister(struct device *dev)
| ^~~~~~~~~~~~~~~~
drivers/video/fbdev/tgafb.c:1387:12: error: ‘tgafb_register’ defined but not used [-Werror=unused-function]
1387 | static int tgafb_register(struct device *dev)
| ^~~~~~~~~~~~~~
so let's make the config option dependencies a bit more explict:
depends on FB
depends on PCI || TC
depends on ALPHA || TC
where that first "FB" is the software configuration dependency, the
second "PCI || TC" is the hardware bus dependency, while that final
"ALPHA || TC" dependency is the "don't bother asking except for these
situations.
We could make that third case have "COMPILE_TEST" as an option, and mark
the register/unregister functions as __maybe_unused, but I'm not sure
it's really worth it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Jensen IO functions are overly copmplicated because some of the IO
addresses refer to special 'local IO' ports, and they get accessed
differently.
That then makes gcc not actually inline them, and since they were marked
"extern inline" when included through the regular <asm/io.h> path, and
then only marked "inline" when included from sys_jensen.c, you never
necessarily got a body for the IO functions at all.
The intent of the sys_jensen.c code is to actually get the non-inlined
copy generated, so remove the 'inline' from the magic macro that is
supposed to sort this all out.
Also, do not mix 'extern inline' functions (that may or may not be
inlined and will not generate a function body if they are not) with
'static inline' (that _will_ generate a function body when not inlined).
Because gcc will complain about this situation:
error: ‘jensen_bus_outb’ is static but used in inline function ‘jensen_outb’ which is not static
because gcc basically doesn't know whether to generate a body for that
static inline function or not for that call site.
So make all of these use that __EXTERN_INLINE marker. Gcc will
generally not inline these things on use, and then generate the function
body out-of-line in sys_jensen.c.
This makes the core IO functions build for the alpha Jensen config.
Not that the rest then builds, because it turns out Jensen also doesn't
enable PCI, which then makes other drievrs very unhappy, but that's a
separate issue.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without CONFIG_PM enabled, the SET_RUNTIME_PM_OPS() macro ends up being
empty, and the only use of tegra_slink_runtime_{resume,suspend} goes
away, resulting in
drivers/spi/spi-tegra20-slink.c:1200:12: error: ‘tegra_slink_runtime_resume’ defined but not used [-Werror=unused-function]
1200 | static int tegra_slink_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-tegra20-slink.c:1188:12: error: ‘tegra_slink_runtime_suspend’ defined but not used [-Werror=unused-function]
1188 | static int tegra_slink_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
mark the functions __maybe_unused to make the build happy.
This hits the alpha allmodconfig build (and others).
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_dma_set_restricted_buffer fails to handle negative return values from
of_property_count_elems_of_size, e.g. when the property does not exist.
This results in an attempt to assign a non-existent reserved memory
region to the device and a warning being printed. Fix the condition to
take negative values into account.
Fixes: f3cfd136ae ("of: restricted dma: Don't fail device probe on rmem init failure")
Cc: Will Deacon <will@kernel.org>
Signed-off-by: David Brazdil <dbrazdil@google.com>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210917131423.2760155-1-dbrazdil@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Pull power management fixes from Rafael Wysocki:
"These fix two cpufreq issues, one in the intel_pstate driver and one
in the core.
Specifics:
- Prevent intel_pstate from avoiding to use HWP, even if instructed
to do so via the kernel command line, when HWP has been enabled
already by the platform firmware (Doug Smythies).
- Prevent use-after-free from occurring in the schedutil cpufreq
governor on exit by fixing a core helper function that attempts to
access memory associated with a kobject after calling kobject_put()
on it (James Morse)"
* tag 'pm-5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: schedutil: Destroy mutex before kobject_put() frees the memory
cpufreq: intel_pstate: Override parameters if HWP forced by BIOS
Pull dma-mapping fixes from Christoph Hellwig:
- page align size in sparc32 arch_dma_alloc (Andreas Larsson)
- tone down a new dma-debug message (Hamza Mahfooz)
- fix the kerneldoc for dma_map_sg_attrs (me)
* tag 'dma-mapping-5.15-1' of git://git.infradead.org/users/hch/dma-mapping:
sparc32: page align size in arch_dma_alloc
dma-debug: prevent an error message from causing runtime problems
dma-mapping: fix the kerneldoc for dma_map_sg_attrs
Pull PCI fixes from Bjorn Helgaas:
- Defer VPD sizing until we actually need the contents; fixes a
boot-time slowdown reported by Dave Jones (Bjorn Helgaas)
- Stop clobbering OF fwnodes when we look for an ACPI fwnode; fixes a
virtio-iommu boot regression (Jean-Philippe Brucker)
- Add AMD GPU multi-function power dependencies; fixes runtime power
management, including GPU resume and temp and fan sensor issues (Evan
Quan)
- Update VMD maintainer to Nirmal Patel (Jon Derrick)
* tag 'pci-v5.15-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add Nirmal Patel as VMD maintainer
PCI: Add AMD GPU multi-function power dependencies
PCI/ACPI: Don't reset a fwnode set by OF
PCI/VPD: Defer VPD sizing until first access
Pull io_uring iov_iter retry fixes from Jens Axboe:
"This adds a helper to save/restore iov_iter state, and modifies
io_uring to use it.
After that is done, we can now kill the iter->truncated addition that
we added for this release. The io_uring change is being overly
cautious with the save/restore/advance, but better safe than sorry and
we can always improve that and reduce the overhead if it proves to be
of concern. The only case to be worried about in this regard is huge
IO, where iteration can take a while to iterate segments.
I spent some time writing test cases, and expanded the coverage quite
a bit from the last posting of this. liburing carries this regression
test case now:
https://git.kernel.dk/cgit/liburing/tree/test/file-verify.c
which exercises all of this. It now also supports provided buffers,
and explicitly tests for end-of-file/device truncation as well.
On top of that, Pavel sanitized the IOPOLL retry path to follow the
exact same pattern as normal IO"
* tag 'iov_iter.3-5.15-2021-09-17' of git://git.kernel.dk/linux-block:
io_uring: move iopoll reissue into regular IO path
Revert "iov_iter: track truncated size"
io_uring: use iov_iter state save/restore helpers
iov_iter: add helper to save iov_iter state
Pull io_uring fixes from Jens Axboe:
"Mostly fixes for regressions in this cycle, but also a few fixes that
predate this release.
The odd one out is a tweak to the direct files added in this release,
where attempting to reuse a slot is allowed instead of needing an
explicit removal of that slot first. It's a considerable improvement
in usability to that API, hence I'm sending it for -rc2.
- io-wq race fix and cleanup (Hao)
- loop_rw_iter() type fix
- SQPOLL max worker race fix
- Allow poll arm for O_NONBLOCK files, fixing a case where it's
impossible to properly use io_uring if you cannot modify the file
flags
- Allow direct open to simply reuse a slot, instead of needing it
explicitly removed first (Pavel)
- Fix a case where we missed signal mask restoring in cqring_wait, if
we hit -EFAULT (Xiaoguang)"
* tag 'io_uring-5.15-2021-09-17' of git://git.kernel.dk/linux-block:
io_uring: allow retry for O_NONBLOCK if async is supported
io_uring: auto-removal for direct open/accept
io_uring: fix missing sigmask restore in io_cqring_wait()
io_uring: pin SQPOLL data before unlocking ring lock
io-wq: provide IO_WQ_* constants for IORING_REGISTER_IOWQ_MAX_WORKERS arg items
io-wq: fix potential race of acct->nr_workers
io-wq: code clean of io_wqe_create_worker()
io_uring: ensure symmetry in handling iter types in loop_rw_iter()
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- fix ANA state updates when a namespace is not present (Anton
Eidelman)
- nvmet: fix a width vs precision bug in
nvmet_subsys_attr_serial_show (Dan Carpenter)
- avoid race in shutdown namespace removal (Daniel Wagner)
- fix io_work priority inversion in nvme-tcp (Keith Busch)
- destroy cm id before destroy qp to avoid use after free (Ruozhu
Li)
- blk-integrity profile registration fixes (Christoph, Lihong)
- blk-cgroup UAF fix (Li)
- blk-mq tag iterator fix (Ming)
- blkcg memory leak fix (Yanfei)
* tag 'block-5.15-2021-09-17' of git://git.kernel.dk/linux-block:
blk-cgroup: fix UAF by grabbing blkcg lock before destroying blkg pd
blkcg: fix memory leak in blk_iolatency_init
nvme: remove the call to nvme_update_disk_info in nvme_ns_remove
block: flush the integrity workqueue in blk_integrity_unregister
block: check if a profile is actually registered in blk_integrity_unregister
nvme-tcp: fix io_work priority inversion
nvme-rdma: destroy cm id before destroy qp to avoid use after free
nvme-multipath: fix ANA state updates when a namespace is not present
nvme: avoid race in shutdown namespace removal
nvmet: fix a width vs precision bug in nvmet_subsys_attr_serial_show()
blk-mq: avoid to iterate over stale request
Pull arm64 fixes and cleanups from Catalin Marinas:
- Fix the memset() size when re-initialising the SVE state.
- Mark __stack_chk_guard as __ro_after_init.
- Remove duplicate include.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Mark __stack_chk_guard as __ro_after_init
arm64/kernel: remove duplicate include in process.c
arm64/sve: Use correct size when reinitialising SVE state
Pull xen fixes from Juergen Gross:
- The first hunk of a Xen swiotlb fixup series fixing multiple minor
issues and doing some small cleanups
- Some further Xen related fixes avoiding WARN() splats when running as
Xen guests or dom0
- A Kconfig fix allowing the pvcalls frontend to be built as a module
* tag 'for-linus-5.15b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
swiotlb-xen: drop DEFAULT_NSLABS
swiotlb-xen: arrange to have buffer info logged
swiotlb-xen: drop leftover __ref
swiotlb-xen: limit init retries
swiotlb-xen: suppress certain init retries
swiotlb-xen: maintain slab count properly
swiotlb-xen: fix late init retry
swiotlb-xen: avoid double free
xen/pvcalls: backend can be a module
xen: fix usage of pmd_populate in mremap for pv guests
xen: reset legacy rtc flag for PV domU
PM: base: power: don't try to use non-existing RTC for storing data
xen/balloon: use a kernel thread instead a workqueue
Pull drm fixes from Dave Airlie:
"Slightly busier than usual rc2, but mostly scattered amdgpu fixes,
some i915 and etnaviv resolves an MMU/runtime PM blowup.
amdgpu:
- UBSAN fix
- Powerplay table update fix
- Fix use after free in BO moves
- Debugfs init fixes
- vblank workqueue fixes for headless devices
- FPU fixes
- sysfs_emit fixes
- SMU updates for cyan skillfish
- Backlight fixes when DMCU is not initialized
- DP MST fixes
- HDCP compliance fix
- Link training fix
- Runtime pm fix
- Panel orientation fixes
- Display GPUVM fix for yellow carp
- Add missing license
amdkfd:
- Drop PCI atomics requirement if proper firmware is available
- Suspend/resume fixes for IOMMUv2 cases
radeon:
- AGP fix
i915:
- Propagate DP link training error returns
- Use max link params for eDP 1.3 and earlier
- Build warning fixes
- Gem selftest fixes
- Ensure wakeref is held before hardware access
etnaviv:
- MMU context vs runtime PM fix"
* tag 'drm-fixes-2021-09-17' of git://anongit.freedesktop.org/drm/drm: (44 commits)
drm/amdgpu/display: add a proper license to dc_link_dp.c
drm/amd/display: Fix white screen page fault for gpuvm
amd/display: enable panel orientation quirks
drm/amdgpu: Demote TMZ unsupported log message from warning to info
drm/amdgpu: Drop inline from amdgpu_ras_eeprom_max_record_count
drm/amd/pm: fix runpm hang when amdgpu loaded prior to sound driver
drm/radeon: pass drm dev radeon_agp_head_init directly
drm/amdgpu: move iommu_resume before ip init/resume
drm/amdgpu: add amdgpu_amdkfd_resume_iommu
drm/amdkfd: separate kfd_iommu_resume from kfd_resume
drm/amd/display: Link training retry fix for abort case
drm/amd/display: Fix unstable HPCP compliance on Chrome Barcelo
drm/amd/display: dsc mst 2 4K displays go dark with 2 lane HBR3
drm/amd/display: Get backlight from PWM if DMCU is not initialized
drm/amdkfd: make needs_pcie_atomics FW-version dependent
drm/amdgpu: add manual sclk/vddc setting support for cyan skilfish(v3)
drm/amdgpu: add some pptable funcs for cyan skilfish(v3)
drm/amdgpu: update SMU driver interface for cyan skilfish(v3)
drm/amdgpu: update SMU PPSMC for cyan skilfish
drm/amdgpu: fix sysfs_emit/sysfs_emit_at warnings(v2)
...
tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
mod_timer(&sp->tx_t, jiffies + ((when + 1) * HZ) / 100);
and the SIXP_TXDELAY walue is sent as a byte over the wire.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
Fixes: 7c49abb4c2 ("drm/rockchip: cdn-dp-core: Make cdn_dp_core_suspend/resume static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers pass a pointer to volatile data to virt_to_bus() and
virt_to_phys(), and that works fine. One exception is alpha. This
results in a number of compile errors such as
drivers/net/wan/lmc/lmc_main.c: In function 'lmc_softreset':
drivers/net/wan/lmc/lmc_main.c:1782:50: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
drivers/atm/ambassador.c: In function 'do_loader_command':
drivers/atm/ambassador.c:1747:58: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
Declare the parameter of virt_to_phys and virt_to_bus as pointer to
volatile to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver isn't enabled most places because of the ISA config
dependency, but alpha still has it. And I think the 'Jensen' actually
did have an ISA slot.
However, it doesn't build cleanly, because the "Vortex bus master" code
just casts the skb->data pointer to 'int':
outl((int) (skb->data), ioaddr + Wn7_MasterAddr);
which is all kinds of broken. Even on a good old traditional PC/AT it
would be broken because the high bits will be random kernel address
bits, but presumably the hardware ignores those bits. I mean, it's ISA.
We're talking 16MB dma limits. The "good old days".
Make the build happy with this kind of craziness by using the proper
isa_virt_to_bus() handling that the full bus master code uses anyway
(the Vortex bus mastering is a limited special case).
Who knows, this might even work.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc fix from Helge Deller:
"Fix a build warning when using the PAGE0 pointer"
* tag 'for-5.15/parisc-4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Use absolute_pointer() to define PAGE0
Pull m68k fixes from Geert Uytterhoeven:
- Warning fixes to mitigate CONFIG_WERROR=y
* tag 'm68k-for-v5.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: mvme: Remove overdue #warnings in RTC handling
m68k: Double cast io functions to unsigned long
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[Why]
The "base_addr_is_mc_addr" field was added for dcn3.1 support but
pa_config was never updated to set it to false.
Uninitialized memory causes it to be set to true which results in
address mistranslation and white screen.
[How]
Use memset to ensure all fields are initialized to 0 by default.
Fixes: 64b1d0e8d5 ("drm/amd/display: Add DCN3.1 HWSEQ")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch allows panel orientation quirks from DRM core to be
used. They attach a DRM connector property "panel orientation"
which indicates in which direction the panel has been mounted.
Some machines have the internal screen mounted with a rotation.
Since the panel orientation quirks need the native mode from the
EDID, check for it in amdgpu_dm_connector_ddc_get_modes.
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the user cannot do anything about the unsupported Trusted Memory Zone
(TMZ) feature, do not warn about it, but make it informational, so
demote the log level from warning to info.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was unusual; normally, inline functions are declared static as
well, and defined in a header file if used by multiple compilation
units. The latter would be more involved in this case, so just drop
the inline declaration for now.
Fixes compile failure building for ppc64le on RHEL 8:
In file included from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.h:32,
from ../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:33:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c: In function ‘amdgpu_ras_recovery_init’:
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras_eeprom.h:90:17: error: inlining failed in call
to ‘always_inline’ ‘amdgpu_ras_eeprom_max_record_count’: function body not available
90 | inline uint32_t amdgpu_ras_eeprom_max_record_count(void);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1985:34: note: called from here
1985 | max_eeprom_records_len = amdgpu_ras_eeprom_max_record_count();
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: c84d46707e "drm/amdgpu: validate bad page threshold in ras(v3)"
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current RUNPM mechanism relies on PMFW to master the timing for BACO
in/exit. And that needs cooperation from sound driver for dstate
change notification for function 1(audio). Otherwise(on sound driver
missing), BACO cannot be kicked in correctly and hang will be observed
on RUNPM exit.
By switching back to legacy message way on sound driver missing,
we are able to fix the runpm hang observed for the scenario below:
amdgpu driver loaded -> runpm suspend kicked -> sound driver loaded
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-and-tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If link training is aborted, it shall be retried if sink is present.
[How]
Check hpd status to find out whether sink is present or not. If sink is
present, then link training shall be tried again with same settings.
Otherwise, link training shall be aborted.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.
[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state
from pbn -> dsc target bpp_x16
bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.
from dsc target bpp_x16 -> pbn
within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);
drm_dp_calc_pbn_mode(int clock, int bpp, bool dsc)
{
return DIV_ROUND_UP_ULL(mul_u32_u32(clock * (bpp / 16), 64 * 1006),
8 * 54 * 1000 * 1000);
}
bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.
pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.
[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc
Cc: stable@vger.kernel.org
Reviewed-by: Scott Foster <Scott.Foster@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.
Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.
We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1666
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On some GPUs the PCIe atomic requirement for KFD depends on the MEC
firmware version. Add a firmware version check for this. The minimum
firmware version that works without atomics can be updated in the
device_info structure for each GPU type.
Move PCIe atomic detection from kgd2kfd_probe into kgd2kfd_device_init
because the MEC firmware is not loaded yet at the probe stage.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add manual sclk/vddc setting supoort via pp_od_clk_voltage sysfs
to maintain consistency with other asics. As cyan skillfish doesn't
support DPM, there is only a single frequency and voltage to adjust.
v2: maintain consistency and add command guide.
v3: adjust user settings storage and coding style.
Command guide:
echo vc point sclk vddc > pp_od_clk_voltage
"vc" - sclk voltage curve
"point" - must be 0
"sclk" - target value of sclk(MHz), should be in safe range
"vddc" - target value of vddc(mV), a 6.25(mV) stepping is
recommended and should be in safe range (the real
vddc is an approximation of target value)
echo c > pp_od_clk_voltage
"c" - commit the changes of sclk and vddc, only after
the commit command, the target values set by "vc"
command will take effect
echo r > pp_od_clk_voltage
"r" - reset sclk and vddc to default value, a subsequent
commit command is needed to take effect
Example:
1) Check default sclk and vddc
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 862mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
2) Set sclk to 1500MHz and vddc to 700mV
$ echo vc 0 1500 700 > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1500Mhz *
OD_VDDC:
0: 693mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
3) Reset sclk and vddc to default
$ echo r > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 874mV *
OD_RANGE:
SCLK: 1000Mhz 2000Mhz
VDDC: 700mV 1129mV
NOTE:
We don't specify an explicit safe range, you can set any values
between min and max at your own risk. Enjoy!
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
