Pull char/misc driver fixes from Greg KH:
"Here are a small number of char/misc driver fixes for 5.17-rc4 for
reported issues. They contain:
- phy driver fixes
- iio driver fix
- eeprom driver fix
- speakup regression fix
- fastrpc fix
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
iio: buffer: Fix file related error handling in IIO_BUFFER_GET_FD_IOCTL
speakup-dectlk: Restore pitch setting
bus: mhi: pci_generic: Add mru_default for Cinterion MV31-W
bus: mhi: pci_generic: Add mru_default for Foxconn SDX55
eeprom: ee1004: limit i2c reads to I2C_SMBUS_BLOCK_MAX
misc: fastrpc: avoid double fput() on failed usercopy
phy: dphy: Correct clk_pre parameter
phy: phy-mtk-tphy: Fix duplicated argument in phy-mtk-tphy
phy: stm32: fix a refcount leak in stm32_usbphyc_pll_enable()
phy: xilinx: zynqmp: Fix bus width setting for SGMII
phy: cadence: Sierra: fix error handling bugs in probe()
phy: ti: Fix missing sentinel for clk_div_table
phy: broadcom: Kconfig: Fix PHY_BRCM_USB config option
phy: usb: Leave some clocks running during suspend
it will cause hwmon node of power1_label is not created.
v2:
the hwmon node of "power1_label" is always needed for all ASICs.
and the patch will remove ASIC type check for "power1_label".
Fixes: ae07970a06 ("drm/amd/pm: add support for hwmon control of slow and fast PPT limit on vangogh")
Signed-off-by: Yang Wang <KevinYang.Wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Even if can_apply_edp_fast_boot is set to 1 at boot, this flag will
be cleared to 0 at S3 resume.
[How]
Keep eDP Vdd on when eDP stream is already enabled.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt order are mapped 1 to 1 to otg id.
e.g. if irq_src=26 corresponds to otg0 then 27->otg1, 28->otg2...
Linux DM registers pflip interrupts per number of crtcs.
In fused pipe case crtc numbers can be less than otg id.
e.g. if one pipe out of 3(otg#0-2) is fused adev->mode_info.num_crtc=2
so DM only registers irq_src 26,27.
This is a bug since if pipe#2 remains unfused DM never gets
otg2 pflip interrupt (irq_src=28)
That may results in gfx failure due to pflip timeout.
[How]
Register pflip interrupts per max num of otg instead of num_crtc
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A number of BIOS versions have a problem with the watermarks table not
being configured properly. This manifests as a very scary looking warning
during resume from s0i3. This should be harmless in most cases and is well
understood, so decrease the assertion to a clearer warning about the problem.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 7707f7227f ("drm/rockchip: Add support for afbc") switched up
the rk3399_vop_big[] register windows, but it did so incorrectly.
The biggest problem is in rk3288_win23_data[] vs.
rk3368_win23_data[] .format field:
RK3288's format: VOP_REG(RK3288_WIN2_CTRL0, 0x7, 1)
RK3368's format: VOP_REG(RK3368_WIN2_CTRL0, 0x3, 5)
Bits 5:6 (i.e., shift 5, mask 0x3) are correct for RK3399, according to
the TRM.
There are a few other small differences between the 3288 and 3368
definitions that were swapped in commit 7707f7227f. I reviewed them to
the best of my ability according to the RK3399 TRM and fixed them up.
This fixes IOMMU issues (and display errors) when testing with BG24
color formats.
Fixes: 7707f7227f ("drm/rockchip: Add support for afbc")
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119161104.1.I1d01436bef35165a8cdfe9308789c0badb5ff46a@changeid
On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.
We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.
And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.
Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 15512021eb)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Architectures others than x86 have a stub implementation calling
WARN_ON_ONCE(). The appropriate headers need to be included, otherwise
the header-test target will fail with:
HDRTEST drivers/gpu/drm/i915/i915_mm.h
In file included from <command-line>:
./drivers/gpu/drm/i915/i915_mm.h: In function ‘remap_io_mapping’:
./drivers/gpu/drm/i915/i915_mm.h:26:2: error: implicit declaration of function ‘WARN_ON_ONCE’ [-Werror=implicit-function-declaration]
26 | WARN_ON_ONCE(1);
| ^~~~~~~~~~~~
v2: Do not include <linux/printk.h> since call to pr_err() has been
removed
Fixes: 67c430bbaa ("drm/i915: Skip remap_io_mapping() for non-x86 platforms")
Cc: Siva Mullati <siva.mullati@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Siva Mullati <siva.mullati@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220131165926.3230642-3-lucas.demarchi@intel.com
(cherry picked from commit 377c675f3c)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
Fixes: 57fb32e632 ("drm/vc4: hdmi: Block odd horizontal timings")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127135116.298278-1-maxime@cerno.tech
The code that set the scdc_enabled flag to ensure it was
disabled at boot time also ran on Pi0-3 where there is no
SCDC support. This lead to a warning in vc4_hdmi_encoder_post_crtc_disable
due to vc4_hdmi_disable_scrambling being called and trying to
read (and write) register HDMI_SCRAMBLER_CTL which doesn't
exist on those platforms.
Only set the flag should the interface be configured to support
more than HDMI 1.4.
Fixes: 1998646129 ("drm/vc4: hdmi: Introduce a scdc_enabled flag")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127134559.292778-1-maxime@cerno.tech
The eDP link rate reported by the DP_MAX_LINK_RATE dpcd register (0xa) is
contradictory to the highest rate supported reported by
EDID (0xc = LINK_RATE_RBR2). The effects of this compounded with commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")' results
in no display modes being found and a dark panel.
For now, simply force the maximum supported link rate for the eDP attached
2018 15" Apple Retina panels.
Additionally, we must also check the firmware revision since the device ID
reported by the DPCD is identical to that of the more capable 16,1,
incorrectly quirking it. We also use said firmware check to quirk the
refreshed 15,1 models with Vega graphics as they use a slightly newer
firmware version.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
The original latencies were causing underflow in some modes.
Resolution: 2880x1620@60p when HDR enable
[How]
1. Replace with the up-to-date watermark values based on new measurments
2. Correct the ddr_wm_table name to DDR5 on DCN31
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
There is underflow / visual corruption DCN301, for high
bandwidth MST DSC configurations such as 2x1440p144 or 2x4k60.
[How]
Use up-to-date watermark values for DCN301.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We observed a GPU hang when querying GMC CG state(i.e.,
cat amdgpu_pm_info) on cyan skillfish. Acctually, cyan
skillfish doesn't support any CG features.
Just prevent it from accessing GMC CG registers.
Signed-off-by: Lang Yu <Lang.Yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This will cause misconfigured systems to not run the GPU suspend
routines.
* In APUs that are properly configured system will go into s2idle.
* In APUs that are intended to be S3 but user selects
s2idle the GPU will stay fully powered for the suspend.
* In APUs that are intended to be s2idle and system misconfigured
the GPU will stay fully powered for the suspend.
* In systems that are intended to be s2idle, but AMD dGPU is also
present, the dGPU will go through S3
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will be used to help make decisions on what to do in
misconfigured systems.
v2: squash in semicolon fix from Stephen Rothwell
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
GuC updates shared memory and KMD reads it. Since this is not
synchronized, we run into a race where the value read is inconsistent.
Sometimes the inconsistency is in reading the upper MSB bytes of the
last_switch_in value. 2 types of cases are seen - upper 8 bits are zero
and upper 24 bits are zero. Since these are non-zero values, it is
not trivial to determine validity of these values. Instead we read the
values multiple times until they are consistent. In test runs, 3
attempts results in consistent values. The upper bound is set to 6
attempts and may need to be tuned as per any new occurences.
Since the duration that gt is parked can vary, the patch also updates
the gt timestamp on unpark before starting the worker.
v2:
- Initialize i
- Use READ_ONCE to access engine record
Fixes: 77cdd054dd ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125020124.788679-2-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 512712a824)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
On some OEM setups users can configure the BIOS for S3 or S2idle.
When configured to S3 users can still choose 's2idle' in the kernel by
using `/sys/power/mem_sleep`. Before commit 6dc8265f98 ("drm/amdgpu:
always reset the asic in suspend (v2)"), the GPU would crash. Now when
configured this way, the system should resume but will use more power.
As such, adjust the `amdpu_acpi_is_s0ix function` to warn users about
potential power consumption issues during their first attempt at
suspending.
Reported-by: Bjoren Dasse <bjoern.daase@gmail.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1824
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.
This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.
Signed-off-by: Nick Lopez <github@glowingmonkey.org>
Fixes: 4d4e9907ff ("drm/nouveau/bios: guard against out-of-bounds accesses to image")
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org
Smatch detected a divide by zero bug in check_overlay_scaling().
drivers/gpu/drm/i915/display/intel_overlay.c:976 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_height'.
drivers/gpu/drm/i915/display/intel_overlay.c:980 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_width'.
Prevent this by ensuring that the dst height and width are non-zero.
Fixes: 02e792fbaa ("drm/i915: implement drmmode overlay support v4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124122409.GA31673@kili
(cherry picked from commit cf5b64f7f1)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Pull drm fixes from Dave Airlie:
"This week's regular normal fixes. amdgpu and msm make up the bulk of
it, with a scattering of fixes elsewhere.
atomic:
- fix CRTC handling during modeset
privcy-screen:
- honor acpi=off
ttm:
- build fix for um
panel:
- add orientation quirk for 1NetBook OneXPlayer
amdgpu:
- Proper fix for otg synchronization logic regression
- DCN3.01 fixes
- Filter out secondary radeon PCI IDs
- udelay fixes
- Fix a memory leak in an error path
msm:
- parameter check fixes
- put_device balancing
- idle/suspend fixes
etnaviv:
- relax submit size checks
vc4:
- fix potential deadlock in DSI code
ast:
- revert 1600x900 mode change"
* tag 'drm-fixes-2022-01-28' of git://anongit.freedesktop.org/drm/drm: (25 commits)
drm/privacy-screen: honor acpi=off in detect_thinkpad_privacy_screen
Revert "drm/ast: Support 1600x900 with 108MHz PCLK"
drm/amdgpu/display: Remove t_srx_delay_us.
drm/amd/display: Wrap dcn301_calculate_wm_and_dlg for FPU.
drm/amd/display: Fix FP start/end for dcn30_internal_validate_bw.
drm/amd/display/dc/calcs/dce_calcs: Fix a memleak in calculate_bandwidth()
drm/amdgpu/display: use msleep rather than udelay for long delays
drm/amdgpu/display: adjust msleep limit in dp_wait_for_training_aux_rd_interval
drm/amdgpu: filter out radeon secondary ids as well
drm/amd/display: change FIFO reset condition to embedded display only
drm/amd/display: Correct MPC split policy for DCN301
drm/amd/display: Fix for otg synchronization logic
drm/etnaviv: relax submit size limits
drm/msm/gpu: Cancel idle/boost work on suspend
drm/msm/gpu: Wait for idle before suspending
drm/atomic: Add the crtc to affected crtc only if uapi.enable = true
drm/msm/dsi: invalid parameter check in msm_dsi_phy_enable
drm/msm/a6xx: Add missing suspend_count increment
drm/msm: Fix wrong size calculation
drm/msm/dpu: invalid parameter check in dpu_setup_dspp_pcc
...
