This patch has a one line oops fix, plus related cleanups.
- The bugfix uses microframe scheduling data given to the hardware to
test "is this a periodic QH", rather than testing for nonzero period.
(Prevents an oops by providing the correct answer.)
- The cleanup going along with the patch should make it clearer what's
going on whenever those bitfields are accessed.
The bug came about when, around January, two new kinds of EHCI interrupt
scheduling operation were added, involving both the high speed (24 KBytes
per millisec) and low/full speed (1-64 bytes per millisec) microframe
scheduling. A driver for the Edirol UA-1000 Audio Capture Unit ran into
the oops; it used one of the newly supported high speed modes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In yenta_socket, we default to using the resource setting of the CardBus
bridge. However, this is a PCI-bus-centric view of resources and thus needs
to be converted to generic resources first. Therefore, add a call to
pcibios_bus_to_resource() call in between. This function is a mere wrapper on
x86 and friends, however on some others it already exists, is added in this
patch (alpha, arm, ppc, ppc64) or still needs to be provided (parisc -- where
is its pcibios_resource_to_bus() ?).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0. This leaves such
a device in an inaccessible state. The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.
The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.
Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot. Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.
Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification. This is
especially true since often many devices are covered by the same
driver. It likely would be necessary to replicate code across dozens
of drivers.
The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register. I believe it is safe to include
this patch as part of the PCI infrastructure.
The cleanest implementation of pci_restore_bars was to call
pci_update_resource. Unfortunately, that does not currently exist
for the sparc64 architecture. The patch below includes a null
implemenation of pci_update_resource for sparc64.
Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Revert this June 17 patch: it broke persistence of timers across execve().
Cc: Roland McGrath <roland@redhat.com>
Cc: george anzinger <george@mvista.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The IA32 ptrace emulation currently returns the wrong registers for fs/gs;
it's returning what x86_64 calls gs_base. We need regs.gsindex in order
for GDB to correctly locate the TLS area. Without this patch, the 32-bit
GDB testsuite bombs on a 64-bit kernel. With it, results look about like
I'd expect, although there are still a handful of kernel-related failures
(vsyscall related?).
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We had a user whose apps weren't working correctly because his "rtc" wasn't
working fully.
For the sake of simplicity, it seems sensible to always enable HPET RTC
emulation.
Remove a special config option for HPET_EMULATE_RTC and make it directly
depend on HPET_TIMER and RTC. This will avoid the hangs when EMULATE_RTC
is not configured and when some userlevel script depends on RTC interrupt,
as in:
http://bugzilla.kernel.org/show_bug.cgi?id=4904
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mremap's move_vma is applying __vm_stat_account to the old vma which may
have already been freed: move it to just before the do_munmap.
mremapping to and fro with CONFIG_DEBUG_SLAB=y showed /proc/<pid>/status
VmSize and VmData wrapping just like in kernel bugzilla #4842, and fixed by
this patch - worth including in 2.6.13, though not yet confirmed that it
fixes that specific report from Frank van Maarseveen.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The included patch fixes a problem where a inotify client would receive a
delete event before the file was actually deleted. The bug affects both
dnotify & inotify.
Signed-off-by: John McCutchan <ttb@tentacle.dhs.org>
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The inotify help text still refers to the character device. Update it.
Fixes kernel bug #4993.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes sure that a keyring that failed to instantiate
properly is destroyed without oopsing [CAN-2005-2099].
The problem occurs in three stages:
(1) The key allocator initialises the type-specific data to all zeroes. In
the case of a keyring, this will become a link in the keyring name list
when the keyring is instantiated.
(2) If a user (any user) attempts to add a keyring with anything other than
an empty payload, the keyring instantiation function will fail with an
error and won't add the keyring to the name list.
(3) The keyring's destructor then sees that the keyring has a description
(name) and tries to remove the keyring from the name list, which oopses
because the link pointers are both zero.
This bug permits any user to take down a box trivially.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch prevents an error during the key session joining operation
from hanging future joins in the D state [CAN-2005-2098].
The problem is that the error handling path for the KEYCTL_JOIN_SESSION_KEYRING
operation has one error path that doesn't release the session management
semaphore. Further attempts to get the semaphore will then sleep for ever in
the D state.
This can happen in four situations, all involving an attempt to allocate a new
session keyring:
(1) ENOMEM.
(2) The users key quota being reached.
(3) A keyring name that is an empty string.
(4) A keyring name that is too long.
Any user may attempt this operation, and so any user can cause the problem to
occur.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The kexec boot is not successful on some power machines since all CPUs are
getting removed from global interrupt queue (GIQ) before kexec boot. Some
systems always expect at least one CPU in GIQ. Hence, this patch will make
sure that only secondary CPUs are removed from GIQ.
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This code was never designed to handle more than one instance of do_work()
running at once.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent change to never ignore the bitmap, revealed that the bitmap isn't
begin flushed properly when an array is stopped.
We call bitmap_daemon_work three times as there is a three-stage pipeline for
flushing updates to the bitmap file.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Firstly, R1BIO_Degraded was being set in a number of places in the resync
code, but is never used there, so get rid of those settings.
Then: When doing a resync, we want to clear the bit in the bitmap iff the
array will be non-degraded when the sync has completed. However the current
code would clear the bitmap if the array was non-degraded when the resync
*started*, which obviously isn't right (it is for 'resync' but not for
'recovery' - i.e. rebuilding a failed drive).
This patch calculated 'still_degraded' and uses the to tell bitmap_start_sync
whether this sync should clear the corresponding bit.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The code currently will ignore the bitmap if the array seem to be in-sync.
This is wrong if the array is degraded, and probably wrong anyway. If the
bitmap says some chunks are not in in-sync, and the superblock says everything
IS in sync, then something is clearly wrong, and it is safer to trust the
bitmap.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Until the bitmap code was added,
modprobe md
would load the md module. But now the md module is called 'md-mod', so we
really need an alias for backwards comparability.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
no_overlay bttv parameter implemented to fix OOPS on some PCI chipsets
(like some VIA) with these behaviors:
1) If pci_quicks does identify the chip as having troubles to
handle PCI2PCI transfers, no_overlay defaults to 1. The user may force
it to 0, to reenable (not recommended).
2) For newer chipsets not blacklisted, no_overlay=1 is provided as a
workaround until PCI chipset included on /drivers/pci/quirks.c
Thanks to Bodo Eggert <7eggert@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_KEXEC breaks UP builds because of a misspelled smp_release_cpus().
Also, the function isn't defined unless built with CONFIG_SMP but it is
needed if we are to go from a UP to SMP kernel. Enable it and document it.
Thanks to Steven Winiecki for reporting this and to Milton for remembering
how it's supposed to work and why.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch fixes oops caused by ide interfaces not on pci. pcibus_to_node
causes the kernel to crash otherwise. Patch also adds a BUG_ON to check if
hwif is NULL.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Cc: Andi Kleen <ak@muc.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Michael Gernoth
As discussed on the handhelds.org Jornada mailinglist, I take over
maintainership of the currently unmaintained Jornada 720-port in
the mainline kernel.
Signed-off-by: Michael Gernoth <michael@gernoth.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several people noticed we dropped quite a bit on benchmark figures.
OK, it was my fault but unfortunately I discovered I ran out of brown
paper bags a while ago and forgot to reorder them.
The issue is that a construct introduced in the conversion of the
driver to use the transport class keyed off whether the block request
was tagged or not. However, the aic7xxx driver doesn't properly set
up the block layer TCQ (it uses the wrong API), so the driver now
things all requests are untagged and we keep it to a queue depth of a
single element. Oops.
The fix is to use the correct TCQ API.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
x86_64 had hardcoded the VM_ numbers so it broke down when the numbers
were changed.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes five bugs in the key management syscall interface:
(1) add_key() returns 0 rather than EINVAL if the key type is "".
Checking the key type isn't "" should be left to lookup_user_key().
(2) request_key() returns ENOKEY rather than EPERM if the key type begins
with a ".".
lookup_user_key() can't do this because internal key types begin with a
".".
(3) Key revocation always returns 0, even if it fails.
(4) Key read can return EAGAIN rather than EACCES under some circumstances.
A key is permitted to by read by a process if it doesn't grant read
access, but it does grant search access and it is in the process's
keyrings. That search returns EAGAIN if it fails, and this needs
translating to EACCES.
(5) request_key() never adds the new key to the destination keyring if one is
supplied.
The wrong macro was being used to test for an error condition: PTR_ERR()
will always return true, whether or not there's an error; this should've
been IS_ERR().
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-Off-By: Linus Torvalds <torvalds@osdl.org>
This removes the calls to device_suspend() from the shutdown path that
were added sometime during 2.6.13-rc*. They aren't working properly on
a number of configs (I got reports from both ppc powerbook users and x86
users) causing the system to not shutdown anymore.
I think it isn't the right approach at the moment anyway. We have
already a shutdown() callback for the drivers that actually care about
shutdown and the suspend() code isn't yet in a good enough shape to be
so much generalized. Also, the semantics of suspend and shutdown are
slightly different on a number of setups and the way this was patched in
provides little way for drivers to cleanly differenciate. It should
have been at least a different message.
For 2.6.13, I think we should revert to 2.6.12 behaviour and have a
working suspend back.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Fix a typo causing a warning in the arm oprofile backtrace code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM fault handler is optimised to make the fast path, err, fast.
The renumbering of the VM_FAULT_* codes broke this because numbers
were used instead of the definitions. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ACPI now uses kmalloc(...,GPF_ATOMIC) during suspend/resume.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For 2.6.12 behaviour, this (EXPERIMENTAL) driver
should not be built.
Update the driver source with latest from Luming.
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Burst mode isn't ready for prime time,
but can be enabled for test via "ec_burst=1"
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Patch from Ian Campbell
On PXA255 there is no way to disable the watchdog. Turning off OIER[E3]
as suggested in the existing comment does not work.
I posted a note to the ARM mailing list a little while ago asking for
opinions from people using SA1100. There was one reponse from Nico who
believes that the SA1100 is the same as the PXA255 in this respect.
You also asked me to involve the watchdog maintainer which I tried to
do but didn't hear anything back. There are only a couple of other
drivers which can't stop the watchdog and there seems to be no
consistancy regarding printing an error etc. I decided to print
something since that matches the case for all the other drivers when
NOWAYOUT is turned on.
Also, I changed the device .name to "watchdog" like most of the other
watchdogs. udev uses it as the device name (by default) and spaces etc.
get in the way.
Superceded 2833/1 because 2.6.13-rc4 caused rejects.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This allows the serial driver autconf to work properly on all the IXP
serial ports. W/o it we basically put the serial port in an unrecoverable
state and lose console.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The IEEE 754 standard specifies that the result of (x - x), where x is
a valid number, should be -0 if the rounding mode is towards minus
infinity or +0 otherwise.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Michael Burian
This file is maintained by RMK's machine registry, it should not be patched.
Signed-off-by: Michael Burian <dynmail1@gassner-waagen.at>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
