There is a problem when ipvlan slaves are created on a master device that
is a vmxnet3 device (ipvlan in VMware guests). The vmxnet3 driver does not
support unicast address filtering. When an ipvlan device is brought up in
ipvlan_open(), the ipvlan driver calls dev_uc_add() to add the hardware
address of the vmxnet3 master device to the unicast address list of the
master device, phy_dev->uc. This inevitably leads to the vmxnet3 master
device being forced into promiscuous mode by __dev_set_rx_mode().
Promiscuous mode is switched on the master despite the fact that there is
still only one hardware address that the master device should use for
filtering in order for the ipvlan device to be able to receive packets.
The comment above struct net_device describes the uc_promisc member as a
"counter, that indicates, that promiscuous mode has been enabled due to
the need to listen to additional unicast addresses in a device that does
not implement ndo_set_rx_mode()". Moreover, the design of ipvlan
guarantees that only the hardware address of a master device,
phy_dev->dev_addr, will be used to transmit and receive all packets from
its ipvlan slaves. Thus, the unicast address list of the master device
should not be modified by ipvlan_open() and ipvlan_stop() in order to make
ipvlan a workable option on masters that do not support unicast address
filtering.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver")
Reported-by: Per Sundstrom <per.sundstrom@redqube.se>
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable_lookup_get_insert_key doesn't have a parameter `data`. It
does have a parameter `key`, however.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
pkaustub@cisco.com is bouncing, remove it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are a couple of read locks that should be write locks.
Fixes: fbb39807e9 ("ionic: support sr-iov operations")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur says:
====================
QorIQ DPAA FMan erratum A050385 workaround
Changes in v2:
- added CONFIG_DPAA_ERRATUM_A050385
- removed unnecessary parenthesis
- changed alignment defines to use only decimal values
The patch set implements the workaround for FMan erratum A050385:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
To reproduce this issue when the workaround is not applied, one
needs to ensure the FMan DMA transaction queue is already full
when a transaction split occurs so the system must be under high
traffic load (i.e. multiple ports at line rate). After the errata
occurs, the traffic stops. The only SoC impacted by this is the
LS1043A, the other ARM DPAA 1 SoC or the PPC DPAA 1 SoCs do not
have this erratum.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Align buffers, data start, SG fragment length to avoid DMA splits.
These changes prevent the A050385 erratum to manifest itself:
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LS1043A SoC is affected by the A050385 erratum stating that
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak thus stopping further packet processing.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FMAN DMA read or writes under heavy traffic load may cause FMAN
internal resource leak; thus stopping further packet processing.
The FMAN internal queue can overflow when FMAN splits single
read or write transactions into multiple smaller transactions
such that more than 17 AXI transactions are in flight from FMAN
to interconnect. When the FMAN internal queue overflows, it can
stall further packet processing. The issue can occur with any one
of the following three conditions:
1. FMAN AXI transaction crosses 4K address boundary (Errata
A010022)
2. FMAN DMA address for an AXI transaction is not 16 byte
aligned, i.e. the last 4 bits of an address are non-zero
3. Scatter Gather (SG) frames have more than one SG buffer in
the SG list and any one of the buffers, except the last
buffer in the SG list has data size that is not a multiple
of 16 bytes, i.e., other than 16, 32, 48, 64, etc.
With any one of the above three conditions present, there is
likelihood of stalled FMAN packet processing, especially under
stress with multiple ports injecting line-rate traffic.
To avoid situations that stall FMAN packet processing, all of the
above three conditions must be avoided; therefore, configure the
system with the following rules:
1. Frame buffers must not span a 4KB address boundary, unless
the frame start address is 256 byte aligned
2. All FMAN DMA start addresses (for example, BMAN buffer
address, FD[address] + FD[offset]) are 16B aligned
3. SG table and buffer addresses are 16B aligned and the size
of SG buffers are multiple of 16 bytes, except for the last
SG buffer that can be of any size.
Additional workaround notes:
- Address alignment of 64 bytes is recommended for maximally
efficient system bus transactions (although 16 byte alignment is
sufficient to avoid the stall condition)
- To support frame sizes that are larger than 4K bytes, there are
two options:
1. Large single buffer frames that span a 4KB page boundary can
be converted into SG frames to avoid transaction splits at
the 4KB boundary,
2. Align the large single buffer to 256B address boundaries,
ensure that the frame address plus offset is 256B aligned.
- If software generated SG frames have buffers that are unaligned
and with random non-multiple of 16 byte lengths, before
transmitting such frames via FMAN, frames will need to be copied
into a new single buffer or multiple buffer SG frame that is
compliant with the three rules listed above.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Patches to bump position index from sysctl seq_next,
from Vasilin Averin.
2) Release flowtable hook from error path, from Florian Westphal.
3) Patches to add missing netlink attribute validation,
from Jakub Kicinski.
4) Missing NFTA_CHAIN_FLAGS in nf_tables_fill_chain_info().
5) Infinite loop in module autoload if extension is not available,
from Florian Westphal.
6) Missing module ownership in inet/nat chain type definition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently passive MPTCP socket can skip including the DACK
option - if the peer sends data before accept() completes.
The above happens because the msk 'can_ack' flag is set
only after the accept() call.
Such missing DACK option may cause - as per RFC spec -
unwanted fallback to TCP.
This change addresses the issue using the key material
available in the current subflow, if any, to create a suitable
dack option when msk ack seq is not yet available.
v1 -> v2:
- adavance the generated ack after the initial MPC packet
Fixes: d22f4988ff ("mptcp: process MP_CAPABLE data option")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to commit 674d9de02a ("NFC: Fix possible memory
corruption when handling SHDLC I-Frame commands") and commit d7ee81ad09
("NFC: nci: Add some bounds checking in nci_hci_cmd_received()") which
added range checks on "pipe".
The "pipe" variable comes skb->data[0] in nfc_hci_msg_rx_work().
It's in the 0-255 range. We're using it as the array index into the
hdev->pipes[] array which has NFC_HCI_MAX_PIPES (128) members.
Fixes: 118278f20a ("NFC: hci: Add pipes table to reference them with a tuple {gate, host}")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When local NET_RX backlog is full due to traffic overrun,
peer veth tx_dropped counter increases. At that time, list
local veth stats, rx_dropped has double value of peer
tx_dropped, even bigger than transmit packets by peer.
In NET_RX softirq process, if any packet drop case happens,
it increases dev's rx_dropped counter and returns NET_RX_DROP.
At veth tx side, it records any error returned from peer netif_rx
into local dev tx_dropped counter.
In veth get stats process, it puts local dev rx_dropped and
peer dev tx_dropped into together as local rx_drpped value.
So that it shows double value of real dropped packets number in
this case.
This patch ignores peer tx_dropped when counting local rx_dropped,
since peer tx_dropped is duplicated to local rx_dropped at most cases.
Signed-off-by: Jiang Lidong <jianglidong3@jd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.6. Only two small fixes this time.
iwlwifi
* fix another initialisation regression with 3168 devices
mt76
* fix memory corruption with too many rx fragments
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeYQGUAAoJEG4XJFUm622bJPoIAJ9lKMQWzHP7s/PouMw4qa3l
KyQHl0uZe6clEULYFi89vaUUzjmTZqsBkQXsKM+0cppxx1IxukLFtQw8UqgEWbpB
eSDajpB5tvt7gSvLjGLyXtxZzj7Bn5T0IdgcPLxg9lmp0EwW/ycbX/XTCDqZSSq0
IHkYKjRBoIhJ+JTZVYGPIk3GDwSb3PTVeT9C239Rj6Jhwou0p1vlopOjAsIr3dv9
PIf/+21wHTtAgVejxKSQV4qUrNT2/J27gXht3hLwkm8goQV01z/3z03bQhEpfvm5
CJr0hZAjLIR1T5RvYCqb41nhTFznlmrBYsozy1EtpMJGfGbNQ2XvRGZCU964lnk=
=5YYp
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-03-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
Second set of fixes for v5.6. Only two small fixes this time.
iwlwifi
* fix another initialisation regression with 3168 devices
mt76
* fix memory corruption with too many rx fragments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We now ignore the "completion" event when using tx queue timestamping,
and only pay attention to the two (high and low) timestamp events. The
NIC will send a pair of timestamp events for every packet transmitted.
The current firmware may merge the completion events, and it is possible
that future versions may reorder the completion and timestamp events.
As such the completion event is not useful.
Without this patch in place a merged completion event on a queue with
timestamping will cause a "spurious TX completion" error. This affects
SFN8000-series adapters.
Signed-off-by: Tom Zhao <tzhao@solarflare.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fibre port supports auto-negotiation, the IMP(Intelligent
Management Process) processes the speed of auto-negotiation
and the user's speed separately.
For below case, the port will get a not link up problem.
step 1: disables auto-negotiation and sets speed to A, then
the driver's MAC speed will be updated to A.
step 2: enables auto-negotiation and MAC gets negotiated
speed B, then the driver's MAC speed will be updated to B
through querying in periodical task.
step 3: MAC gets new negotiated speed A.
step 4: disables auto-negotiation and sets speed to B before
periodical task query new MAC speed A, the driver will ignore
the speed configuration.
This patch fixes it by skipping speed and duplex checking when
fibre port supports auto-negotiation.
Fixes: 22f48e24a2 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nft will loop forever if the kernel doesn't support an expression:
1. nft_expr_type_get() appends the family specific name to the module list.
2. -EAGAIN is returned to nfnetlink, nfnetlink calls abort path.
3. abort path sets ->done to true and calls request_module for the
expression.
4. nfnetlink replays the batch, we end up in nft_expr_type_get() again.
5. nft_expr_type_get attempts to append family-specific name. This
one already exists on the list, so we continue
6. nft_expr_type_get adds the generic expression name to the module
list. -EAGAIN is returned, nfnetlink calls abort path.
7. abort path encounters the family-specific expression which
has 'done' set, so it gets removed.
8. abort path requests the generic expression name, sets done to true.
9. batch is replayed.
If the expression could not be loaded, then we will end up back at 1),
because the family-specific name got removed and the cycle starts again.
Note that userspace can SIGKILL the nft process to stop the cycle, but
the desired behaviour is to return an error after the generic expr name
fails to load the expression.
Fixes: eb014de4fd ("netfilter: nf_tables: autoload modules from the abort path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When registers a phy_device successful, should terminate the loop
or the phy_device would be registered in other addr. If there are
multiple PHYs without reg properties, it will go wrong.
Signed-off-by: Dajun Jin <adajunjin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware can support more than 8 queues currently limited by
netif_get_num_default_rss_queues(). So, rework and fix checks for max
number of queues to allocate. The checks should be based on how many are
actually supported by hardware, OR the number of online cpus; whichever
is lower.
Fixes: 5952dde723 ("cxgb4: set maximal number of default RSS queues")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
This should improve the error message when the PHY validate in the MAC
driver failed. I ran into this problem multiple times that I put wrong
interface values into the device tree and was searching why it is
failing with -22 (-EINVAL). This should make it easier to spot the
problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink trigger command does not exist. While rewriting the
documentation for devlink into the reStructuredText format,
documentation for the trigger command was accidentally merged in. This
occurred because the author was also working on a potential extension to
devlink regions which included this trigger command, and accidentally
squashed the documentation incorrectly.
Further review eventually settled on using the previously unused "new"
command instead of creating a new trigger command.
Fix this by removing mention of the trigger command from the
documentation.
Fixes: 0b0f945f54 ("devlink: add a file documenting devlink regions", 2020-01-10)
Noticed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for tunnel source and
destination ports to the netlink policy.
Fixes: af308b94a2 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add missing attribute validation for NFTA_PAYLOAD_CSUM_FLAGS
to the netlink policy.
Fixes: 1814096980 ("netfilter: nft_payload: layer 4 checksum adjustment for pseudoheader fields")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If hook registration fails, the hooks allocated via nft_netdev_hook_alloc
need to be freed.
We can't change the goto label to 'goto 5' -- while it does fix the memleak
it does cause a warning splat from the netfilter core (the hooks were not
registered).
Fixes: 3f0465a9ef ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables")
Reported-by: syzbot+a2ff6fa45162a5ed4dd3@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Without patch:
# dd if=/proc/net/ip_tables_matches # original file output
conntrack
conntrack
conntrack
recent
recent
icmp
udplite
udp
tcp
0+1 records in
0+1 records out
65 bytes copied, 5.4074e-05 s, 1.2 MB/s
# dd if=/proc/net/ip_tables_matches bs=62 skip=1
dd: /proc/net/ip_tables_matches: cannot skip to specified offset
cp <<< end of last line
tcp <<< and then unexpected whole last line once again
0+1 records in
0+1 records out
7 bytes copied, 0.000102447 s, 68.3 kB/s
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Without the patch:
# dd if=/proc/net/xt_recent/SSH # original file outpt
src=127.0.0.4 ttl: 0 last_seen: 6275444819 oldest_pkt: 1 6275444819
src=127.0.0.2 ttl: 0 last_seen: 6275438906 oldest_pkt: 1 6275438906
src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
0+1 records in
0+1 records out
204 bytes copied, 6.1332e-05 s, 3.3 MB/s
Read after lseek into middle of last line (offset 140 in example below)
generates expected end of last line and then unexpected whole last line
once again
# dd if=/proc/net/xt_recent/SSH bs=140 skip=1
dd: /proc/net/xt_recent/SSH: cannot skip to specified offset
127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
src=127.0.0.3 ttl: 0 last_seen: 6275441953 oldest_pkt: 1 6275441953
0+1 records in
0+1 records out
132 bytes copied, 6.2487e-05 s, 2.1 MB/s
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If .next function does not change position index,
following .show function will repeat output related
to current position index.
Cc: stable@vger.kernel.org
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Place phylink_start()/phylink_stop() inside dsa_port_enable() and
dsa_port_disable(), which ensures that we call phylink_stop() before
tearing down phylink - which is a documented requirement. Failure
to do so can cause use-after-free bugs.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu says:
====================
Fix IPv6 peer route update
Currently we have two issues for peer route update on IPv6.
1. When update peer route metric, we only updated the local one.
2. If peer address changed, we didn't remove the old one and add new one.
The first two patches fixed these issues and the third patch add new
tests to cover it.
With the fixes and updated test:
]# ./fib_tests.sh
IPv6 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
TEST: Set metric with peer route on local side [ OK ]
TEST: User specified metric on local address [ OK ]
TEST: Set metric with peer route on peer side [ OK ]
TEST: Modify metric with peer route on local side [ OK ]
TEST: Modify metric with peer route on peer side [ OK ]
IPv4 prefix route tests
TEST: Default metric [ OK ]
TEST: User specified metric on first device [ OK ]
TEST: User specified metric on second device [ OK ]
TEST: Delete of address on first device [ OK ]
TEST: Modify metric of address [ OK ]
TEST: Prefix route removed on link down [ OK ]
TEST: Prefix route with metric on link up [ OK ]
TEST: Modify metric of .0/24 address [ OK ]
TEST: Set metric of address with peer route [ OK ]
TEST: Modify metric of address with peer route [ OK ]
Tests passed: 22
Tests failed: 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update {ipv4, ipv6}_addr_metric_test with
1. Set metric of address with peer route and see if the route added
correctly.
2. Modify metric and peer address for peer route and see if the route
changed correctly.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we modify the peer route and changed it to a new one, we should
remove the old route first. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::3 proto kernel metric 256 pref medium
This patch depend on the previous patch "net/ipv6: need update peer route
when modify metric" to update new peer route after delete old one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we modify the route metric, the peer address's route need also
be updated. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 60 pref medium
2001:db8::2 proto kernel metric 60 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 60 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 61 pref medium
Fixes: 8308f3ff17 ("net/ipv6: Add support for specifying metric of connected routes")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: add missing netlink policies
Recent one-off fixes motivated me to do some grepping for
more missing netlink attribute policies. I didn't manage
to even produce a KASAN splat with these, but it should
be possible with sufficient luck. All the missing policies
are pretty trivial (NLA_Uxx).
I've only tested the devlink patches, the rest compiles.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for vendor subcommand attributes
to the netlink policy.
Fixes: 9e58095f96 ("NFC: netlink: Implement vendor command support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for NFC_ATTR_TARGET_INDEX
to the netlink policy.
Fixes: 4d63adfe12 ("NFC: Add NFC_CMD_DEACTIVATE_TARGET support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for NFC_ATTR_SE_INDEX
to the netlink policy.
Fixes: 5ce3f32b52 ("NFC: netlink: SE API implementation")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for TIPC_NLA_PROP_MTU
to the netlink policy.
Fixes: 901271e040 ("tipc: implement configuration of UDP media MTU")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for TEAM_ATTR_OPTION_ARRAY_INDEX
to the netlink policy.
Fixes: b13033262d ("team: introduce array options")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for TEAM_ATTR_OPTION_PORT_IFINDEX
to the netlink policy.
Fixes: 80f7c6683f ("team: add support for per-port options")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for TCA_TAPRIO_ATTR_TXTIME_DELAY
to the netlink policy.
Fixes: 4cfd5779bd ("taprio: Add support for txtime-assist mode")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing attribute validation for TCA_FQ_ORPHAN_MASK
to the netlink policy.
Fixes: 06eb395fa9 ("pkt_sched: fq: better control of DDOS traffic")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
