Hyper-V identifies vCPUs by Virtual Processor Index, which can be
queried via HV_X64_MSR_VP_INDEX msr. It is defined by the spec as a
sequential number which can't exceed the maximum number of vCPUs per VM.
APIC ids can be sparse and thus aren't a valid replacement for VP
indices.
Current KVM uses its internal vcpu index as VP_INDEX. However, to make
it predictable and persistent across VM migrations, the userspace has to
control the value of VP_INDEX.
This patch achieves that, by storing vp_index explicitly on vcpu, and
allowing HV_X64_MSR_VP_INDEX to be set from the host side. For
compatibility it's initialized to KVM vcpu index. Also a few variables
are renamed to make clear distinction betweed this Hyper-V vp_index and
KVM vcpu_id (== APIC id). Besides, a new capability,
KVM_CAP_HYPERV_VP_INDEX, is added to allow the userspace to skip
attempting msr writes where unsupported, to avoid spamming error logs.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Adds another flag bit (bit 2) to MSR_KVM_ASYNC_PF_EN. If bit 2 is 1,
async page faults are delivered to L1 as #PF vmexits; if bit 2 is 0,
kvm_can_do_async_pf returns 0 if in guest mode.
This is similar to what svm.c wanted to do all along, but it is only
enabled for Linux as L1 hypervisor. Foreign hypervisors must never
receive async page faults as vmexits, because they'd probably be very
confused about that.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There is a flaw in the Hyper-V SynIC implementation in KVM: when message
page or event flags page is enabled by setting the corresponding msr,
KVM zeroes it out. This is problematic because on migration the
corresponding MSRs are loaded on the destination, so the content of
those pages is lost.
This went unnoticed so far because the only user of those pages was
in-KVM hyperv synic timers, which could continue working despite that
zeroing.
Newer QEMU uses those pages for Hyper-V VMBus implementation, and
zeroing them breaks the migration.
Besides, in newer QEMU the content of those pages is fully managed by
QEMU, so zeroing them is undesirable even when writing the MSRs from the
guest side.
To support this new scheme, introduce a new capability,
KVM_CAP_HYPERV_SYNIC2, which, when enabled, makes sure that the synic
pages aren't zeroed out in KVM.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Adds the plumbing to disable A/D bits in the MMU based on a new role
bit, ad_disabled. When A/D is disabled, the MMU operates as though A/D
aren't available (i.e., using access tracking faults instead).
To avoid SP -> kvm_mmu_page.role.ad_disabled lookups all over the
place, A/D disablement is now stored in the SPTE. This state is stored
in the SPTE by tweaking the use of SPTE_SPECIAL_MASK for access
tracking. Rather than just setting SPTE_SPECIAL_MASK when an
access-tracking SPTE is non-present, we now always set
SPTE_SPECIAL_MASK for access-tracking SPTEs.
Signed-off-by: Peter Feiner <pfeiner@google.com>
[Use role.ad_disabled even for direct (non-shadow) EPT page tables. Add
documentation and a few MMU_WARN_ONs. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts
pending.
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=6hNK
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.13
- vcpu request overhaul
- allow timer and PMU to have their interrupt number
selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
Conflicts:
arch/s390/include/asm/kvm_host.h
In some cases, userspace needs to get or set all ais states for example
migration. So we introduce a new group KVM_DEV_FLIC_AISM_ALL to provide
interfaces to get or set the adapter-interruption-suppression mode for
all ISCs. The corresponding documentation is updated.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
* Add the struct used in the ioctls to get and set CMMA attributes.
* Add the two functions needed to get and set the CMMA attributes for
guest pages.
* Add the two ioctls that use the aforementioned functions.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
* Add a migration state bitmap to keep track of which pages have dirty
CMMA information.
* Disable CMMA by default, so we can track if it's used or not. Enable
it on first use like we do for storage keys (unless we are doing a
migration).
* Creates a VM attribute to enter and leave migration mode.
* In migration mode, CMMA is disabled in the SIE block, so ESSA is
always interpreted and emulated in software.
* Free the migration state on VM destroy.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Now that userspace can set the virtual SMT mode by enabling the
KVM_CAP_PPC_SMT capability, it is useful for userspace to be able
to query the set of possible virtual SMT modes. This provides a
new capability, KVM_CAP_PPC_SMT_POSSIBLE, to provide this
information. The return value is a bitmap of possible modes, with
bit N set if virtual SMT mode 2^N is available. That is, 1 indicates
SMT1 is available, 2 indicates that SMT2 is available, 3 indicates
that both SMT1 and SMT2 are available, and so on.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This introduces a new KVM capability to control how KVM behaves
on machine check exception (MCE) in HV KVM guests.
If this capability has not been enabled, KVM redirects machine check
exceptions to guest's 0x200 vector, if the address in error belongs to
the guest. With this capability enabled, KVM will cause a guest exit
with the exit reason indicating an NMI.
The new capability is required to avoid problems if a new kernel/KVM
is used with an old QEMU, running a guest that doesn't issue
"ibm,nmi-register". As old QEMU does not understand the NMI exit
type, it treats it as a fatal error. However, the guest could have
handled the machine check error if the exception was delivered to
guest's 0x200 interrupt vector instead of NMI exit in case of old
QEMU.
[paulus@ozlabs.org - Reworded the commit message to be clearer,
enable only on HV KVM.]
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This allows userspace to set the desired virtual SMT (simultaneous
multithreading) mode for a VM, that is, the number of VCPUs that
get assigned to each virtual core. Previously, the virtual SMT mode
was fixed to the number of threads per subcore, and if userspace
wanted to have fewer vcpus per vcore, then it would achieve that by
using a sparse CPU numbering. This had the disadvantage that the
vcpu numbers can get quite large, particularly for SMT1 guests on
a POWER8 with 8 threads per core. With this patch, userspace can
set its desired virtual SMT mode and then use contiguous vcpu
numbering.
On POWER8, where the threading mode is "strict", the virtual SMT mode
must be less than or equal to the number of threads per subcore. On
POWER9, which implements a "loose" threading mode, the virtual SMT
mode can be any power of 2 between 1 and 8, even though there is
effectively one thread per subcore, since the threads are independent
and can all be in different partitions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
First we define an ABI using the vcpu devices that lets userspace set
the interrupt numbers for the various timers on both the 32-bit and
64-bit KVM/ARM implementations.
Second, we add the definitions for the groups and attributes introduced
by the above ABI. (We add the PMU define on the 32-bit side as well for
symmetry and it may get used some day.)
Third, we set up the arch-specific vcpu device operation handlers to
call into the timer code for anything related to the
KVM_ARM_VCPU_TIMER_CTRL group.
Fourth, we implement support for getting and setting the timer interrupt
numbers using the above defined ABI in the arch timer code.
Fifth, we introduce error checking upon enabling the arch timer (which
is called when first running a VCPU) to check that all VCPUs are
configured to use the same PPI for the timer (as mandated by the
architecture) and that the virtual and physical timers are not
configured to use the same IRQ number.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Since we got support for devices in userspace which allows reporting the
PMU overflow output status to userspace, we should actually allow
creating the PMU on systems without an in-kernel irqchip, which in turn
requires us to slightly clarify error codes for the ABI and move things
around for the initialization phase.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZEZihAAoJEEtpOizt6ddyGDYH/jmGjDMnryORn2P2o10dUQKJ
RnHTQYnpOYqnprlkFtZFpmK+mjl/a8R1Btb7GK2EwmovTR95pMYPRqtrCTOL0aQA
4OToh7+vFGatwxsGCS6utazdhmx0UT/LhO/GEF4G1zOb7eVa4ZtS1NKLP2WjPD1E
RU3Qn8wa0pESv3tJScv8qo2+PWVX4krbFllhY2Hk0AkVQcI66ExkdVq4ikm1eUXn
rxzIayLG2bv3KEPNCzozdwoY9tDL+b40q6vN/RHGJmM05SZbbSx2/Bkw2RbslSpD
2hvhHWX7xeuEBcd5mZO7sP4WS3hM/BI8eX7q+uMeNJ9B+nM82yjGfOTtglVi2cc=
=JfvQ
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12-round2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
Second round of KVM/ARM Changes for v4.12.
Changes include:
- A fix related to the 32-bit idmap stub
- A fix to the bitmask used to deode the operands of an AArch32 CP
instruction
- We have moved the files shared between arch/arm/kvm and
arch/arm64/kvm to virt/kvm/arm
- We add support for saving/restoring the virtual ITS state to
userspace
Clarify what is meant by the save/restore ABI only supporting virtual
physical interrupts.
Relax the requirement of the order that the collection entries are
written in and be clear that there is no particular ordering enforced.
Some cosmetic changes in the capitalization of ID names to align with
the GICv3 manual and remove the empty line in the bottom of the patch.
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
support; virtual interrupt controller performance improvements; support
for userspace virtual interrupt controller (slower, but necessary for
KVM on the weird Broadcom SoCs used by the Raspberry Pi 3)
* MIPS: basic support for hardware virtualization (ImgTec
P5600/P6600/I6400 and Cavium Octeon III)
* PPC: in-kernel acceleration for VFIO
* s390: support for guests without storage keys; adapter interruption
suppression
* x86: usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits; emulation of CPL3 CPUID faulting
* generic: first part of VCPU thread request API; kvm_stat improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZEHUkAAoJEL/70l94x66DBeYH/09wrpJ2FjU4Rqv7FxmqgWfH
9WGi4wvn/Z+XzQSyfMJiu2SfZVzU69/Y67OMHudy7vBT6knB+ziM7Ntoiu/hUfbG
0g5KsDX79FW15HuvuuGh9kSjUsj7qsQdyPZwP4FW/6ZoDArV9mibSvdjSmiUSMV/
2wxaoLzjoShdOuCe9EABaPhKK0XCrOYkygT6Paz1pItDxaSn8iW3ulaCuWMprUfG
Niq+dFemK464E4yn6HVD88xg5j2eUM6bfuXB3qR3eTR76mHLgtwejBzZdDjLG9fk
32PNYKhJNomBxHVqtksJ9/7cSR6iNPs7neQ1XHemKWTuYqwYQMlPj1NDy0aslQU=
=IsiZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- HYP mode stub supports kexec/kdump on 32-bit
- improved PMU support
- virtual interrupt controller performance improvements
- support for userspace virtual interrupt controller (slower, but
necessary for KVM on the weird Broadcom SoCs used by the Raspberry
Pi 3)
MIPS:
- basic support for hardware virtualization (ImgTec P5600/P6600/I6400
and Cavium Octeon III)
PPC:
- in-kernel acceleration for VFIO
s390:
- support for guests without storage keys
- adapter interruption suppression
x86:
- usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits
- emulation of CPL3 CPUID faulting
generic:
- first part of VCPU thread request API
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
kvm: nVMX: Don't validate disabled secondary controls
KVM: put back #ifndef CONFIG_S390 around kvm_vcpu_kick
Revert "KVM: Support vCPU-based gfn->hva cache"
tools/kvm: fix top level makefile
KVM: x86: don't hold kvm->lock in KVM_SET_GSI_ROUTING
KVM: Documentation: remove VM mmap documentation
kvm: nVMX: Remove superfluous VMX instruction fault checks
KVM: x86: fix emulation of RSM and IRET instructions
KVM: mark requests that need synchronization
KVM: return if kvm_vcpu_wake_up() did wake up the VCPU
KVM: add explicit barrier to kvm_vcpu_kick
KVM: perform a wake_up in kvm_make_all_cpus_request
KVM: mark requests that do not need a wakeup
KVM: remove #ifndef CONFIG_S390 around kvm_vcpu_wake_up
KVM: x86: always use kvm_make_request instead of set_bit
KVM: add kvm_{test,clear}_request to replace {test,clear}_bit
s390: kvm: Cpu model support for msa6, msa7 and msa8
KVM: x86: remove irq disablement around KVM_SET_CLOCK/KVM_GET_CLOCK
kvm: better MWAIT emulation for guests
KVM: x86: virtualize cpuid faulting
...
Add description for how to save GICV3 LPI pending bit into
guest RAM pending tables.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Add description for how to access ITS registers and how to save/restore
ITS tables into/from memory.
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Since commit 80f5b5e700 ("KVM: remove vm mmap method"), the VM mmap
handler is gone. Remove the corresponding documentation.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Changes include:
- Using the common sysreg definitions between KVM and arm64
- Improved hyp-stub implementation with support for kexec and kdump on the 32-bit side
- Proper PMU exception handling
- Performance improvements of our GIC handling
- Support for irqchip in userspace with in-kernel arch-timers and PMU support
- A fix for a race condition in our PSCI code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY/IasAAoJEEtpOizt6ddyd7gH/2N3BIMxi/Uqigx0e0byA43s
f+8gNq8A71VBTERGW2l9QP1/AZAXpQYNWdWmN2jn+91x2yoVL7AT00gEsliSLEZv
tqZaTGFXKi1vNihYrxEWm1mfVNzhRrnbW6vjLrO4J5Advq7T3OWhNuVt2BLTxz3Y
h0iqOWNVrUD9h3QSBFH8tz7yXhguDTSppAcXbE0tACdRu4vN50wqEWokHJG5TsMG
Tl3KYWrcc3YCKlAJGuJi7t5rMrXk+g1q6HnxlIN6OSk0POC2Vmw9/Gigtltj1Qwh
ZEAwsnka/U8ak8WaWeZa3EsGTSFSoAk/+pKv2FB8mFN+uOmWDqVlEiol4dW49AY=
=mEOk
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.12.
Changes include:
- Using the common sysreg definitions between KVM and arm64
- Improved hyp-stub implementation with support for kexec and kdump on the 32-bit side
- Proper PMU exception handling
- Performance improvements of our GIC handling
- Support for irqchip in userspace with in-kernel arch-timers and PMU support
- A fix for a race condition in our PSCI code
Conflicts:
Documentation/virtual/kvm/api.txt
include/uapi/linux/kvm.h
- Detect all function codes for KMA and export the features
for use in the cpu model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=elz2
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: MSA8 feature for guests
- Detect all function codes for KMA and export the features
for use in the cpu model
msa6 and msa7 require no changes.
msa8 adds kma instruction and feature area.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Guests that are heavy on futexes end up IPI'ing each other a lot. That
can lead to significant slowdowns and latency increase for those guests
when running within KVM.
If only a single guest is needed on a host, we have a lot of spare host
CPU time we can throw at the problem. Modern CPUs implement a feature
called "MWAIT" which allows guests to wake up sleeping remote CPUs without
an IPI - thus without an exit - at the expense of never going out of guest
context.
The decision whether this is something sensible to use should be up to the
VM admin, so to user space. We can however allow MWAIT execution on systems
that support it properly hardware wise.
This patch adds a CAP to user space and a KVM cpuid leaf to indicate
availability of native MWAIT execution. With that enabled, the worst a
guest can do is waste as many cycles as a "jmp ." would do, so it's not
a privilege problem.
We consciously do *not* expose the feature in our CPUID bitmap, as most
people will want to benefit from sleeping vCPUs to allow for over commit.
Reported-by: "Gabriel L. Somlo" <gsomlo@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[agraf: fix amd, change commit message]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows the host kernel to handle H_PUT_TCE, H_PUT_TCE_INDIRECT
and H_STUFF_TCE requests targeted an IOMMU TCE table used for VFIO
without passing them to user space which saves time on switching
to user space and back.
This adds H_PUT_TCE/H_PUT_TCE_INDIRECT/H_STUFF_TCE handlers to KVM.
KVM tries to handle a TCE request in the real mode, if failed
it passes the request to the virtual mode to complete the operation.
If it a virtual mode handler fails, the request is passed to
the user space; this is not expected to happen though.
To avoid dealing with page use counters (which is tricky in real mode),
this only accelerates SPAPR TCE IOMMU v2 clients which are required
to pre-register the userspace memory. The very first TCE request will
be handled in the VFIO SPAPR TCE driver anyway as the userspace view
of the TCE table (iommu_table::it_userspace) is not allocated till
the very first mapping happens and we cannot call vmalloc in real mode.
If we fail to update a hardware IOMMU table unexpected reason, we just
clear it and move on as there is nothing really we can do about it -
for example, if we hot plug a VFIO device to a guest, existing TCE tables
will be mirrored automatically to the hardware and there is no interface
to report to the guest about possible failures.
This adds new attribute - KVM_DEV_VFIO_GROUP_SET_SPAPR_TCE - to
the VFIO KVM device. It takes a VFIO group fd and SPAPR TCE table fd
and associates a physical IOMMU table with the SPAPR TCE table (which
is a guest view of the hardware IOMMU table). The iommu_table object
is cached and referenced so we do not have to look up for it in real mode.
This does not implement the UNSET counterpart as there is no use for it -
once the acceleration is enabled, the existing userspace won't
disable it unless a VFIO container is destroyed; this adds necessary
cleanup to the KVM_DEV_VFIO_GROUP_DEL handler.
This advertises the new KVM_CAP_SPAPR_TCE_VFIO capability to the user
space.
This adds real mode version of WARN_ON_ONCE() as the generic version
causes problems with rcu_sched. Since we testing what vmalloc_to_phys()
returns in the code, this also adds a check for already existing
vmalloc_to_phys() call in kvmppc_rm_h_put_tce_indirect().
This finally makes use of vfio_external_user_iommu_id() which was
introduced quite some time ago and was considered for removal.
Tests show that this patch increases transmission speed from 220MB/s
to 750..1020MB/s on 10Gb network (Chelsea CXGB3 10Gb ethernet card).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
1. guarded storage support for guests
This contains an s390 base Linux feature branch that is necessary
to implement the KVM part
2. Provide an interface to implement adapter interruption suppression
which is necessary for proper zPCI support
3. Use more defines instead of numbers
4. Provide logging for lazy enablement of runtime instrumentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iQIcBAABAgAGBQJY50fGAAoJEBF7vIC1phx8TK4P/0y7J6go7NFniVXf0K5/teAZ
kH6BRwoWQDCGAwkpz8fqhKTNxdEq1bjLS5aNf2R3oGt61yoKim4GLSYeRymhKWo0
WZbwq8VpCWxjysx4wyg1nm4J05EDqaPvfxtD9ONCxZNXvPeZR5pIY1uo3twuNROS
z+bOtP1YK7FyzbgGsHnc47YKrOMa3LwTQfAAhf3eVHs5f9cksIqlQYlo/H7fJY96
Z3qpZmrwWP5avZAenxfUKS2dEiT2lzFvUP1waYwm4sZ7fImdgBRlnFzFK/O7qiIV
c9KHW+qao37NU1AsqJibXZvFQBJixKxWa8nCKsagpkZAMDoPNoutHsxXpNJNrp4S
Zq+OWbiYRKXnndGI94RtMUE+bmRvcj37a648+nwzRPA9N889GQR829qKLANsqCwY
7bM3gE9d5BkAASp0uZ4bgrfyU4tlGTH8WLNSLM+upeOGjWEk3HdOEFuJQNspgaWQ
oaAl4TROQhGvZXYxzTHP26jEG0IAIkUd2CUULAe8lZ2vk+kc4xPAfhjQ41DFembz
fDMXXKgjtHvT6Z5USbGJdkOBkhzGyOuETZJyrj7D60OmlHXeoBPgWIJ21cS8ZU4F
M0cM+1DcXbOOKjfIbZRbLh9OdAhBya8VzHnyw7T2vl9hXIAhEH9MwTfVsnBujdca
Q4BBOIh3HV9VfT0exaaF
=Jtjb
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux
From: Christian Borntraeger <borntraeger@de.ibm.com>
KVM: s390: features for 4.12
1. guarded storage support for guests
This contains an s390 base Linux feature branch that is necessary
to implement the KVM part
2. Provide an interface to implement adapter interruption suppression
which is necessary for proper zPCI support
3. Use more defines instead of numbers
4. Provide logging for lazy enablement of runtime instrumentation
We have 2 modes for dealing with interrupts in the ARM world. We can
either handle them all using hardware acceleration through the vgic or
we can emulate a gic in user space and only drive CPU IRQ pins from
there.
Unfortunately, when driving IRQs from user space, we never tell user
space about events from devices emulated inside the kernel, which may
result in interrupt line state changes, so we lose out on for example
timer and PMU events if we run with user space gic emulation.
Define an ABI to publish such device output levels to userspace.
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In order to help people understanding the hyp-stub API that exists
between the host kernel and the hypervisor mode (whether a hypervisor
has been installed or not), let's document said API.
As with any form of documentation, I expect it to become obsolete
and completely misleading within 20 minutes after having being merged.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Legacy device assignment has been deprecated since 4.2 (released
1.5 years ago). VFIO is better and everyone should have switched to it.
If they haven't, this should convince them. :)
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce a cap to enable AIS facility bit, and add documentation
for this capability.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add basic support for the MIPS Virtualization Module (generally known as
MIPS VZ) in KVM. We primarily support the ImgTec P5600, P6600, I6400,
and Cavium Octeon III cores so far. Support is included for the
following VZ / guest hardware features:
- MIPS32 and MIPS64, r5 (VZ requires r5 or later) and r6
- TLBs with GuestID (IMG cores) or Root ASID Dealias (Octeon III)
- Shared physical root/guest TLB (IMG cores)
- FPU / MSA
- Cop0 timer (up to 1GHz for now due to soft timer limit)
- Segmentation control (EVA)
- Hardware page table walker (HTW) both for root and guest TLB
Also included is a proper implementation of the TLBR instruction for the
trap & emulate MIPS KVM implementation.
Preliminary MIPS architecture changes are applied directly with Ralf's
ack.
-----BEGIN PGP SIGNATURE-----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=smiL
-----END PGP SIGNATURE-----
Merge tag 'kvm_mips_4.12_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/kvm-mips
From: James Hogan <james.hogan@imgtec.com>
KVM: MIPS: VZ support, Octeon III, and TLBR
Add basic support for the MIPS Virtualization Module (generally known as
MIPS VZ) in KVM. We primarily support the ImgTec P5600, P6600, I6400,
and Cavium Octeon III cores so far. Support is included for the
following VZ / guest hardware features:
- MIPS32 and MIPS64, r5 (VZ requires r5 or later) and r6
- TLBs with GuestID (IMG cores) or Root ASID Dealias (Octeon III)
- Shared physical root/guest TLB (IMG cores)
- FPU / MSA
- Cop0 timer (up to 1GHz for now due to soft timer limit)
- Segmentation control (EVA)
- Hardware page table walker (HTW) both for root and guest TLB
Also included is a proper implementation of the TLBR instruction for the
trap & emulate MIPS KVM implementation.
Preliminary MIPS architecture changes are applied directly with Ralf's
ack.
Inject adapter interrupts on a specified adapter which allows to
retrieve the adapter flags, e.g. if the adapter is subject to AIS
facility or not. And add documentation for this interface.
For adapters subject to AIS, handle the airq injection suppression
for a given ISC according to the interruption mode:
- before injection, if NO-Interruptions Mode, just return 0 and
suppress, otherwise, allow the injection.
- after injection, if SINGLE-Interruption Mode, change it to
NO-Interruptions Mode to suppress the following interrupts.
Besides, add tracepoint for suppressed airq and AIS mode transitions.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Provide an interface for userspace to modify AIS
(adapter-interruption-suppression) mode state, and add documentation
for the interface. Allowed target modes are ALL-Interruptions mode
and SINGLE-Interruption mode.
We introduce the 'simm' and 'nimm' fields in kvm_s390_float_interrupt
to store interruption modes for each ISC. Each bit in 'simm' and
'nimm' targets to one ISC, and collaboratively indicate three modes:
ALL-Interruptions, SINGLE-Interruption and NO-Interruptions. This
interface can initiate most transitions between the states; transition
from SINGLE-Interruption to NO-Interruptions via adapter interrupt
injection will be introduced in a following patch. The meaningful
combinations are as follows:
interruption mode | simm bit | nimm bit
------------------|----------|----------
ALL | 0 | 0
SINGLE | 1 | 0
NO | 1 | 1
Besides, add tracepoint to track AIS mode transitions.
Co-Authored-By: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In order to properly implement adapter-interruption suppression, we
need a way for userspace to specify which adapters are subject to
suppression. Let's convert the existing (and unused) 'pad' field into
a 'flags' field and define a flag value for suppressible adapters.
Besides, add documentation for the interface.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY5MItAAoJEEtpOizt6ddy4mUH/1Z2rt2mUAYFQpWD/vy9WMxf
zJKMtcLlZZGjeU78zFfWuOxEo1bbDO+tOTV1docNnY8xjyszCZ5XKOqMeo2a7Vfh
1QYHxJTOmgxcRmMsOnJpqUXhhYm9hDxrbU88U/wvoNllLjWBea01ZXiJbWFPBssT
jrdtcCVstDGp3x3D91RgYNNzj9jNw80RBekACZZwYokDRpBZyUb8DYKfUgABFEKT
UPiHrxb8UOVqvbCuXMBNzhUZcuMoAh3oY02R9sV7u1QOXAJYfRV4fOV12fIcYbHf
tnyU8cCxEkSI1pHrpVG6SStcMt8yznQ+UPo0okQNBJXim2yI8+QKHtQlvx7Tjo8=
=tPDd
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
From: Christoffer Dall <cdall@linaro.org>
KVM/ARM Fixes for v4.11-rc6
Fixes include:
- Fix a problem with GICv3 userspace save/restore
- Clarify GICv2 userspace save/restore ABI
- Be more careful in clearing GIC LRs
- Add missing synchronization primitive to our MMU handling code
As an oversight, for GICv2, we accidentally export the GICC_PMR register
in the format of the GICH_VMCR.VMPriMask field in the lower 5 bits of a
word, meaning that userspace must always use the lower 5 bits to
communicate with the KVM device and must shift the value left by 3
places to obtain the actual priority mask level.
Since GICv3 supports the full 8 bits of priority masking in the ICH_VMCR,
we have to fix the value we export when emulating a GICv2 on top of a
hardware GICv3 and exporting the emulated GICv2 state to userspace.
Take the chance to clarify this aspect of the ABI.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
Add emulation of Memory Accessibility Attribute Registers (MAARs) when
necessary. We can't actually do anything with whatever the guest
provides, but it may not be possible to clear Guest.Config5.MRP so we
have to emulate at least a pair of MAARs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_PWBase, CP0_PWField, CP0_PWSize, and
CP0_PWCtl registers for controlling the guest hardware page table walker
(HTW) present on P5600 and P6600 cores. These guest registers need
initialising on R6, context switching, and exposing via the KVM ioctl
API when they are present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_SegCtl0, CP0_SegCtl1, and CP0_SegCtl2
registers, as found on P5600 and P6600 cores. These guest registers need
initialising, context switching, and exposing via the KVM ioctl API when
they are present.
They also require the GVA -> GPA translation code for handling a GVA
root exception to be updated to interpret the segmentation registers and
decode the faulting instruction enough to detect EVA memory access
instructions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_ContextConfig and CP0_XContextConfig
(MIPS64 only) registers, as found on P5600 and P6600 cores. These guest
registers need initialising, context switching, and exposing via the KVM
ioctl API when they are present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add support for VZ guest CP0_BadInstr and CP0_BadInstrP registers, as
found on most VZ capable cores. These guest registers need context
switching, and exposing via the KVM ioctl API when they are present.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add the main support for the MIPS Virtualization ASE (A.K.A. VZ) to MIPS
KVM. The bulk of this work is in vz.c, with various new state and
definitions elsewhere.
Enough is implemented to be able to run on a minimal VZ core. Further
patches will fill out support for guest features which are optional or
can be disabled.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add a new KVM_CAP_MIPS_64BIT capability to indicate that 64-bit MIPS
guests are available and supported. In this case it should still be
possible to run 32-bit guest code. If not available it won't be possible
to run 64-bit guest code and the instructions may not be available, or
the kernel may not support full context switching of 64-bit registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Add new KVM_CAP_MIPS_VZ and KVM_CAP_MIPS_TE capabilities, and in order
to allow MIPS KVM to support VZ without confusing old users (which
expect the trap & emulate implementation), define and start checking
KVM_CREATE_VM type codes.
The codes available are:
- KVM_VM_MIPS_TE = 0
This is the current value expected from the user, and will create a
VM using trap & emulate in user mode, confined to the user mode
address space. This may in future become unavailable if the kernel is
only configured to support VZ, in which case the EINVAL error will be
returned and KVM_CAP_MIPS_TE won't be available even though
KVM_CAP_MIPS_VZ is.
- KVM_VM_MIPS_VZ = 1
This can be provided when the KVM_CAP_MIPS_VZ capability is available
to create a VM using VZ, with a fully virtualized guest virtual
address space. If VZ support is unavailable in the kernel, the EINVAL
error will be returned (although old kernels without the
KVM_CAP_MIPS_VZ capability may well succeed and create a trap &
emulate VM).
This is designed to allow the desired implementation (T&E vs VZ) to be
potentially chosen at runtime rather than being fixed in the kernel
configuration.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Emulate the HYPCALL instruction added in the VZ ASE and used by the MIPS
paravirtualised guest support that is already merged. The new hypcall.c
handles arguments and the return value. No actual hypercalls are yet
supported, but this still allows us to safely step over hypercalls and
set an error code in the return value for forward compatibility.
Non-zero HYPCALL codes are not handled.
We also document the hypercall ABI which asm/kvm_para.h uses.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-doc@vger.kernel.org
This patch adds guarded storage support for KVM guest. We need to
setup the necessary control blocks, the kvm_run structure for the
new registers, the necessary wrappers for VSIE, as well as the
machine check save areas.
GS is enabled lazily and the register saving and reloading is done in
KVM code. As this feature adds new content for migration, we provide
a new capability for enablement (KVM_CAP_S390_GS).
Signed-off-by: Fan Zhang <zhangfan@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEEUOvtSCFqLxY/7px3jc41VjAi5XoFAli6ANEPHGNvcmJldEBs
d24ubmV0AAoJEI3ONVYwIuV6GcsQAKQsgmXmT+3ZpoCDzGF/MvZLra8/xjYSWqKZ
jXsUKFmlef7aHZRC79Vw0VyEJdNc+QrmoXCNr9BVl4+z8curDbsGE9/dgV05shAL
vbCuDLNkAYb4o7Kld8cAJQxefs/C/+8CIFZAICICz7L6rgutz8NluVkO7mdqQrYD
2uJl3P2paXKiLDqb2MANGJL9C9ALUnArTopjyK9MIBapuPulVHZse33Ytd4V0951
RKMIEPccZetioZC55qnO2O5sJ+O7nXNIQafzggy1rA2MIcHnkm/zARdBfYgevJBf
dgqfumkCB8Wc/8oB+XRNyKDNH6IXyTk3rd1QssVZVmHlDLB3cfBMpDl5cKV5D3BX
DOrLxPL8Cf8CGbAvyjQcd4b8qaYMJ/fSu2yJFFcL0nOjEucIKBzhIj5cxsGSKcsF
6d5ubv9sXvwzrKxhTkU5mPoE4J+zyaBs+NCE9qEZoxbjokufETEGXWoCMLTXRkiG
mwD52F+QG0aBHEMMh7kgRwxsoGdY9Tm4u6FL/IppUswG0I/Vobp7AwApRwCBzHIM
/V92Be1Ye6bwWatdUZs2NGXP6yy1eBVv7rEof5+2WVwUiLNcFEaHV/1r6fUbj73u
MtKkz3NiVUApPXapa4rTkyjynv+EL7Vexkv6n81JVKHaztODOiIIHSvIBHvXz2wD
Bpxrsx4j
=tZdW
-----END PGP SIGNATURE-----
Merge tag 'docs-4.11-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A few fixes for the docs tree, including one for a 4.11 build
regression"
* tag 'docs-4.11-fixes' of git://git.lwn.net/linux:
Documentation/sphinx: fix primary_domain configuration
docs: Fix htmldocs build failure
doc/ko_KR/memory-barriers: Update control-dependencies section
pcieaer doc: update the link
Documentation: Update path to sysrq.txt
