The direct register access ioctls were defined as kernel internal only,
but they are very useful for debugging hardware from userspace and are
used as such. Officially export them.
VIDIOC_INT_[SG]_REGISTER is renamed to VIDIOC_DBG_[SG]_REGISTER
Definition of ioctl and struct v4l2_register is moved from v4l2-common.h
to videodev2.h.
Types used in struct v4l2_register are changed to the userspace
exportable versions (u32 -> __u32, etc).
Use of VIDIOC_DBG_S_REGISTER requires CAP_SYS_ADMIN permission, so move
the check into the video_ioctl2() dispatcher so it doesn't need to be
duplicated in each driver's call-back function. CAP_SYS_ADMIN check is
added to pvrusb2 (which doesn't use video_ioctl2).
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for these ioctls to the video_ioctl2 system and the cx88
driver.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Nexus CA needs to use a different routing on saa7115 module.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The keymap is based on a previous patch by Jussi Kukkonen.
This remote is identified by subsystem_device id 0x1010.
Signed-off-by: Ville-Pekka Vainio <vpivaini@cs.helsinki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the following compile error:
<-- snip -->
...
LD drivers/media/video/built-in.o
drivers/media/video/saa7134/built-in.o:(.data+0x85ec): multiple definition of `ir_rc5_remote_gap'
drivers/media/video/bt8xx/built-in.o:(.data+0x734c): first defined here
drivers/media/video/saa7134/built-in.o:(.data+0x85f0): multiple definition of `ir_rc5_key_timeout'
drivers/media/video/bt8xx/built-in.o:(.data+0x7350): first defined here
make[4]: *** [drivers/media/video/built-in.o] Error 1
<-- snip -->
Since this variables were needlessly global, this patch implements the
trivial fix of making them static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The commands CX2341X_DEC_SET_AUDIO_OUTPUT, CX2341X_DEC_SET_AV_DELAY and
CX2341X_ENC_SET_3_2_PULLDOWN are not implemented in the Conexant firmware.
So these commands are removed. This also means that the V4L2_CID_MPEG_VIDEO_PULLDOWN
control in cx2341x.c and pvrusb2-hdw.c is removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Besides adding the board specific code, this patch moves
the RC5 decoding code from bt8xx to ir-functions.c to make it available
for all drivers.
Signed-off-by: Marc Fargas <telenieko.telenieko.com>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
include/media/ir-common.h:78: error: field 'work' has incomplete type
drivers/media/common/ir-functions.c: In function 'ir_rc5_timer_end':
drivers/media/common/ir-functions.c:301: error: 'jiffies' undeclared (first use in this function)
drivers/media/common/ir-functions.c:301: error: (Each undeclared identifier is reported only once)
drivers/media/common/ir-functions.c:301: error: for each function it appears in.)
drivers/media/common/ir-functions.c:347: error: 'HZ' undeclared (first use in this function)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some tuners require using cGainNormal instead of cGainLow for
high sensibility on FM reception.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert SAA7146_IER_{DIS,EN}ABLE macros to inline functions.
Fixes a problem with macro expansion (reported by C.Y.M).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Protect the access to the IER register of the SAA7146 by the device
spinlock. I2C transfers may use interrupt mode now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This converts the budget-ci driver so that it uses ir-common for some of its
IR processing. In particular, the keymap for the Nova-T (sub 13c2:1011) is
switched to the Hauppauge grey/black keymap, of which the keys on the
supplied R808 remote control form a subset.
The old budget-ci keymap is moved to ir-keymaps.c and is used for other
remotes.
The debounce logic for buggy remotes (i.e. Zenith) is made conditional the
new debounce parameter and defaults to off (so that repeat keypresses aren't
ignored for all working remotes).
Some parts are based on Darren Salt's dvb-ir patchset.
Signed-off-by: David Hardeman <david@hardeman.nu>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
video_ioctl2 will auto-generate standard entries at ENUM_FMT.
Also, now, a driver may return a subset of the video array at
the return, to be stored as the current_norm.
For example, a driver may ask for V4L2_STD_PAL. At return,
driver may change it to V4L2_STD_PAL_B. This way, a futher call
to G_STD will return the exact detected video std.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to input from Steven Toth from Hauppauge the tveeprom module has
been extended to detect the presence of an IR transmitter (aka IR-blaster).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds a V4L2 driver for the OmniVision OV7670 camera.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Two defines for V4L2, needed by the Cafe camera driver:
1) Add the RGB444 image format
2) Add the "init" internal command which is separate from "reset".
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A generic change to cards to allow any board to specify whether
it needs the wm8775 module loaded (by the core) or not.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (180 commits)
V4L/DVB (4641): Trivial: use lowercase letters in hex subsystem ids
V4L/DVB (4639): Cx88: add autodetection for alternate revision of Leadtek PVR
V4L/DVB (4638): Basic DVB-T and analog TV support for the HVR1300.
V4L/DVB (4637): Add a default method for VIDIOC_G_PARM
V4L/DVB (4635): Extend bttv and saa7134 to check for both AGP and PCI PCI failure case
V4L/DVB (4634): Zr36120: implement pcipci checks
V4L/DVB (4632): Zoran: Implement pcipci failure check
V4L/DVB (4631): Av7110: remove V4L2_CAP_VBI_CAPTURE flag
V4L/DVB (4630): Av7110: FW_LOADER depemdency fixed
V4L/DVB (4629): Saa7134: add card support for Proteus Pro 2309
V4L/DVB (4628): Fix VIDIOC_ENUMSTD ioctl in videodev.c
V4L/DVB (4627): Vivi crashes with mplayer
V4L/DVB (4626): On saa7111/7113, LUMA_CTRL need a different value
V4L/DVB (4624): Tvaudio: Replaced kernel_thread() with kthread_run()
V4L/DVB (4622): Copy-paste bug in videodev.c
V4L/DVB (4620): Fix AGC configuration for MOD3000P-based boards
V4L/DVB (4619): Fixes some I2C dependencies on V4L devices
V4L/DVB (4617): Problem with dibusb-mb.c USB IDs
V4L/DVB (4616): [PATCH] Nebula DigiTV USB RC support
V4L/DVB (4614): Export symbol saa7134_tvaudio_setmute from saa7134 for saa7134-alsa
...
Add card support for Proteus Pro 2309, based on saa7130 bridge
Signed-off-by: Michal Majchrowicz <mmajchrowicz@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The extra argument makes it possible to reset subsystems of a chip if
that is supported.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a tuner config parameter for TDA9887, default_pll_gating_18, that
changes the L standard PLL gating value from 36% to 0% (datasheet says
0%, tda9887 code says 18%).
Turn this on for Microtune 4049FM5, as recomended by tuner datasheet.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Norwood PCI TV Tuner (non-pro)
Signed-off-by: Peter Naulls <peter@chocky.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All radio devices use an obsolete mode of opening/release driver.
Since this is not V4L1 core, better to keep the method available for more
time than to rewrite open/release without a radio device to test, since the
newer method is much more complex than the previous one (although providing
support for multiple opens and multiple devices).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We get hundreds of these:
include/media/v4l2-dev.h:348: warning: ignoring return value of 'class_device_create_file', declared with attribute warn_unused_result
Handle it, and propagate the __must_check back a level.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
V4L1 support should be disabled when no CONFIG_VIDEO_V4L1_COMPAT is defined,
to allow checking for broken V4L2 ports. This is very important during the
migration phase for V4L2 API.
However, userspace apps should be capable of using both APIs, since they need
to test at runtime, via VIDIOCGCAP ioctl, if V4L1 is supported. So, when
__KERNEL__ is not defined, those ioctls and corresponding structs should be
visible.
This patch also removes the obsolete defines HAVE_V4L1 and HAVE_V4L2, that
where causing some confusion, and were replaced by CONFIG_VIDEO_V4L1_COMPAT
and CONFIG_VIDEO_V4L2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Check __must_check warnings for class_device_register and class_device_create_file
video_device_create_file was declared as a void, but instead should
return the int value of class_device_create_file.
Move the check from bttv-driver.c into v4l2-dev.h, because all other
callers of video_device_create_file must also be checked.
Replace the call to class_device_create_file in videodev.c with
video_device_create_file, as defined in v4l2-dev.h, so that the
return value of class_device_create_file will be checked.
Check the return value of class_device_register in videodev.c and
pvrusb2-sysfs.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Many tda9887 settings depend on the chosen tuner. Expand the tuner parameters
to include these tda9887 settings.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
A card number is not unique enough. Instead, let the caller specify the
prefix of the status messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_CID_MPEG_STREAM_VBI_FMT controls if and how VBI data is embedded in
an MPEG stream. Currently only one format is supported: the format designed
for the ivtv driver. This should be extended with new standard formats
(such as defined for DVB) in the future.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Most uses a tda988[5/6/7] IF demodulator as part of the device.
Having this as a separate stuff makes harder to configure it, since there
are some tda9887 options that are tuner-dependent and should be bound into
tuner-types structures.
This patch merges tda9887 module into tuner. More work is required to make
tuner-types to properly use it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It's better to use explicit enums. It reduces the chance of someone
inserting new enums in the middle which would break things.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CX2341X port was always set to 'memory', but 'streaming' is also possible
ivtv uses the memory (DMA) interface with the CX2341X, while pvrusb2 and
cx88-blackbird use the streaming interface. This setting is now selectable
by the driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds the cx2341x.c module that handles the programming of the Conexant
cx23415/6 MPEG encoder chip used by cx88-blackbird, pvrusb2 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Control processing is often duplicated in the various drivers. Unfortunately,
simple things like the names of controls are often different between drivers,
even though it is the same controls. Adding in the new extended controls and
the need for having control helper functions became apparent.
Several functions have now been added to v4l2-common to do things like
filling the v4l2_queryctrl and v4l2_querymenu structs, to check for
valid control input and to move to the next control when enumerating
over all controls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
videodev.c copies the control list specified in struct v4l2_ext_controls
to kernel space.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The videodev.h and videodev2.h describe the public API for V4L and V4L2.
It shouldn't have there any kernel-specific stuff. Those were moved to
v4l2-dev.h.
This patch removes some uneeded headers and include v4l2-common.h on all
V4L driver. This header includes device implementation of V4L2 API provided
on v4l2-dev.h as well as V4L2 internal ioctls that provides connections
between master driver and its i2c devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Videodev now is capable of better handling V4L2 api, by
processing V4L2 ioctls and using callbacks to the driver.
The drivers should be migrated to the newer way and the older
one will be obsoleted soon.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for a new cx88 card, including it's remote
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for the older (?) Pinnacle PCTV remotes (with all buttons
colored in grey). There's no autodetection for the type of remote, though;
saa7134 defaults to the colored one, to use the grey remote the
"pinnacle_remote=1" option must be passed to the saa7134 module
Signed-off-by: Sylvain Pasche <sylvain.pasche@gmail.com>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Date:
There are several drivers now using those cx2341x registers. This patch
creates a separate header for those registers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add v4l2 compatibility
Include the decompressor (legal problem has been resolv by Alan Cox)
Faster decoder and easier to maintain, optimize, ...
Can export to userland compressed stream
Support more cameras, lot of bugs are fixed.
Signed-off-by: Luc Saillard <luc@saillard.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently in /sys/class/dvb/dvbX.demuxY/ we have:
dev
uevent
With the patch, we have (for a PCI DVB device):
dev
device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:03:0d.0
uevent
So userspace tools can (finally) work out which physical device a DVB adapter
refers to. Previously you had to kinda look through dmesg and hope that it
hadn't been dumped out of the buffer. This makes debugging a lot easier if
the system has been up for a long time!
This is done by adding an extra 'struct device *' parameter to
dvb_register_adapter(). It will work with any kind of standard
linux 'device'. Additionally, if someone has an embedded system which does
things differently, they can simply supply 'NULL' and the behaviour will be
as before - the link will simply not appear.
Ack'd-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some saa7115-based cards use a different crystal frequency and a different
audio clock generation. Add a new VIDIOC_INT_S_CRYSTAL_FREQ command to be
able to set these values.
Also change the default APLL setting to 0. It makes no sense to have the
audio clock independent from the video clock, this can lead to audio/video
synchronization problems. Setting this to 0 is also consistent with the old
saa7114.c source and the way the Hauppauge Windows driver sets it.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Renamed various msp3400 routing defines to be more consistent and less
confusing. Esp. the MSP_DSP_OUT defines were confusing since it is really
a DSP input.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for the uPD64031A NEC Electronics Ghost Reduction i2c device
- Add support for the uPD6408x NEC Electronics 3-Dimensional Y/C separation
i2c device.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Takeru Komoriya <komoriya@paken.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- implement VIDIOC_INT_S_AUDIO_ROUTING for msp3400 and tvaudio
- use the new command in bttv, pvrusb2 and em28xx.
- remove the now obsolete MSP_SET_MATRIX from msp3400 (yeah!)
- remove the obsolete VIDIOC_S_AUDIO from msp3400.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved msp3400.h to msp3400-driver.h.
Created media/msp3400.h with the new routing defines and lots of comments.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cleanup audio input handling in bttv and tvaudio:
- inputs were specified that were never used
- mute was handled as a special input which led to confusing code
- confusing naming made it difficult to see if the setting was for
i2c or gpio.
The old audiochip.h input names moved to tvaudio.h. Currently this
is used both by tvaudio and msp3400 until the msp3400 implements the
new msp3400-specific inputs.
Detect in bttv the tvaudio and msp3400 i2c clients and use these
client pointers to set the inputs directly instead of broadcasting the
command.
Removed AUDC_SET_INPUT. Now replaced by VIDIOC_S_AUDIO. This will be
replaced again later by the new ROUTING commands.
Removed VIDIOC_G_AUDIO implementations in i2c drivers: this command is
a user level command and not to be used internally. It wasn't called at
all anyway.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I2C_foo were used for some i2c addresses. Bad, since those constants could
mean other i2c chip things.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Missing a Makefile for bt8xx
- rds.h were at wrong directory, since it is a global header for an internal
interface
- tda7432 and tda9875 were dependent from bttv.h
- bttv.h were holding i2c addresses
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Video_buf were concerned to allow PCI devices to be used as
video capture devices. This patch extends video_buf features
by virtualizing pci-dependent functions and allowing other
type of devices to use it.
It is still DMA centric, although it may be used also by
devices that emulates scatter/gather behavior or a DMA device
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, em28xx uses saa7115 instead of saa711x.
saa7115 driver is capable of handling saa 7113, 7114 and 7115.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added tuner_lg_taln_pal_secam_ranges
- renamed tuner 66 from TUNER_LG_NTSC_TALN_MINI to TUNER_LG_TALN
- updated FlyTV mini Asus Digimatrix with new tuner
Thanks-to: Rickard Osser <ricky@osser.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The tuner used in DViCO FusionHDTV DVB-T hybrid is made by Thomson
- renamed tuner and dvb_pll structs accordingly
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the FE6600 tuner used on the DVB-T Hybrid board.
Add support for the Zarlink ZL10353 DVB-T demodulator, which supersedes the
MT352, used on the DViCO FusionHDTV DVB-T Hybrid and later model Plus boards.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added a new function that allows printing ioctl arguments.
This makes easier to include debug code under v4l ioctl
handling.
Also fixed some declarations on internal ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for xc3028 to v4l which adds support for:
* Terratec Hybrid XS (analogue)
* Hauppauge HVR 900 (analogue)
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner_params element is an array of undefined length,
with each array member being a set of parameters for each
video standard type.
The number of members in the tuner_params array
will be stored in tuners[]->count
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Move config byte from tuner_params to tuner_range struct.
- dvb tuners must be able to set different config byte for each range.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add new internal VIDIOC_INT commands for setting the tuner mode,
for putting a chip into standby mode and to set/get the routing
of inputs/outputs of audio or video of a chip. These new commands
will replace older commands that are no longer up to the task.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove duplicated keymaps and add keymap for KWorld LTV883IR.
Thanks to Jon Ferguson <jon@sd-6.org>.
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- All the keymaps have the same structure, and can be shared between different
chips, so it makes no sense having them scattered between the input files.
This aggregates them all at ir-common module.
- Added new Hauppauge remote (Hauppauge grey), contributed by J.O. Aho
<trizt@iname.com> (with some small changes)
Changed KEY_KPx (keypad numerals) references to KEY_x, to avoid problems
when NumLock is off (suggested by Peter Missel <peter.missel@onlinehome.de>)
- Some cleanups at IR code
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tuner_params->tda988x is unused right now, so let's disable it for 2.6.16
- This is currently happening at the card level, but the plan
is to move this configuration into the tuner_params configuration.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Moved MSP_SET_MATRIX to v4l2-common.h
- Fix typos and integer overflows in tea5767.c
- Split old freq field into a tv_freq and a radio_freq. Prevents
that a radio tuner is initialized with a tv frequency or vice versa.
- When switching to radio mode initialize the tuner with the last
used radio frequency (this was already done for the TV mode).
As a result of these changes the tuner module now remembers the
last set radio and TV frequencies, which is what you would expect
to happen.
- Move out of range frequencies to the closest valid frequency as per
v4l2 API spec.
- Fix incorrect initial radio frequency (multiplier is 16000, not 16)
- Add boundary check for out of range frequencies.
- Use new flag to check if the order of the CB and freq. depends on
the last set frequency. That is needed for some tuners or you can
get static as a result. The flag is added for those tuners where I know
that the datasheet indicates that this is necessary.
- For this new check use the last set div value, not the last frequency
as radio frequencies are always much higher due to the 16000 multiplier.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tda988x parameters should be defined per tuner_param_type,
for each tuner_params array member.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add param_type dvbs2
- disable all dvb param_types, which will not
be needed until we merge dvb-pll.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for Samsung tuner TCPN 2121P30A, used in
Hauppauge PVR-500 cards.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tunertype struct redefined to allow one or more tuner_params structs
per tuner definition, one for each video standard.
- Each tuner_params struct has an element containing an arbitrary
amount of tuner_ranges.
(this is needed for dvb tuners - to be handled later)
- A tuner_range may be referenced by multiple tuner_params structs.
There are many duplicates in here. Reusing tuner_range structs,
rather than defining new ones for each tuner, will cut down on
memory usage, and is preferred when possible.
- tunertype struct contains an element, has_tda988x.
We must set this for all tunertypes that contain a tda988x
chip, and then we can remove this setting from the various
card structs.
- Improves tuners array memory usage efficiency.
- Right now, all tuners are using the first tuner_params[] array element
for analog mode. In the future, we will be merging similar tuner
definitions together, such that each tuner definition will have a
tuner_params struct for each available video standard. At that point,
the tuner_params[] array element will be chosen based on the video
standard in use.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Debug global var is already used inside kernel, so renamed
debug to tuner_debug for the tuner module
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Debug global var is already used inside kernel.
- v4l_dbg now expects the debug var
- global vars inside msp34xx renamed to msp_*
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Implemented v4l2 api for sliced vbi data output
to pass WSS data from userspace to the av7110
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Convert diagnostics over to the new v4l2-common.h macros.
- deprecated tuner_debug option, the new option is debug.
- renamed cx25840_debug to debug.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Added new v4l_err, v4l_warn, v4l_info and v4l_dbg macros to
v4l2-common.h for use in v4l-dvb i2c drivers. This ensures
a unique prefix for each device instance.
- At a later stage these macros may be reimplemented using the
device-generic macros from device.h.
- Converted the msp3400 driver to the new macros.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Now, all internal ioctls are at v4l2-common.h
- removed unused ioctl at saa6752hs.h
- all debug ioctl code moved to v4l2-common.c
- removed duplicated stuff from other cards
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Calculate the audio master clock registers from the actual
frequencies. This simplifies the code and it also prepares
for adding CGC2 support.
- VIDIOC_INT_AUDIO_CLOCK_FREQ now receives an u32 instead of
an enum. It is more generic and actually easier to implement.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Added some comments to make clearer how to use ioctl api to handle
multiple tuners at the same board.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Created a new ioctl to control I2S speed. Old calls to an
inadequate V4L2 API replaced.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Corrected Thomson DTT 7611 tuner programming, based on spec sheet
- renamed to Thomson DTT 761x
- applies to DTT 7611 7611A 7612 7613 7613A 7614 7615 7615A
(DTT 7610 is similar, but slightly different programming)
- corrected frequency ranges for analog and digital modes
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Debug message changed to be coherent with other modules
- added ntsc parameter
- parameters moved to the beginning at the file
- tuner_status moved to a better position.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Set the tuner takeover point to 0x10 for NTSC/radio and 0x14 for PAL/SECAM.
- Allow override through TDA9887_SET_CONFIG
- PAL-N belongs with PAL-BG as does PAL-H. PAL-Nc belongs to PAL-M
- Add SECAM-BGH
- Set video freq to cVideoIF_38_90 for DK standards.
- Add cTunerGainLow to radio, change deemphasis to 75 for mono.
- Add ntsc module param for 'M' and 'J' (Japanese) standards.
- Fix module handling for 2.4.
- Now able to select all standards through pal/secam/ntsc module options
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Remove AUDC_CONFIG_PINNACLE horror. This also fixes radio support
for mt20xx tuners.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Fix wrong tuner.h define for tuner 46 (it's a Panasonic, not a Microtune).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Now when kbuild passes KBUILD_MODNAME with "" do not __stringify it when
used. Remove __stringnify for all users.
This also fixes the output of:
$ ls -l /sys/module/
drwxr-xr-x 4 root root 0 2006-01-05 14:24 pcmcia
drwxr-xr-x 4 root root 0 2006-01-05 14:24 pcmcia_core
drwxr-xr-x 3 root root 0 2006-01-05 14:24 "processor"
drwxr-xr-x 3 root root 0 2006-01-05 14:24 "psmouse"
The quoting of the module names will be gone again.
Thanks to GregKH + Kay Sievers for reproting this.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers/media/video and usb/media drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add workaround for Hauppauge PVR150 hardware problem with tuner models 85, 99
and 112 (model numbers as reported by tveeprom). The audio standard
autodetection does not always work correctly for these models.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added a mac address field to the tveeprom structure.
- allow callers to query the MAC address.
- removed some redundant eeprom parsing code in cx88-cards.c (specific to
Hauppauge DVB products) Instead, placed calls directly to the single eeprom
parsing function in tveeprom.c
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a new include for internal V4L2 ioctls and API
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- The pinnacle handler & remote are common to saa7134 PCI boards and em28xx
USB boards, so the keymap was moved to ir-common and the keyhandler is back
to ir-kbd-i2c
- request_module("ir-kbd-i2c") is no longer necessary at saa7134-core since
saa7134.ko now depends on ir-kbd-i2c.ko to get the keyhandler
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Some changes to allow compiling cx88 and saa7134 without V4L1 support.
- This patch will help obsoleting V4L1 API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- New config option for tda9887 to specifically set intercarrier
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Several Improvement on I2C IR handling for em2820:
- moved Pinnacle IR table (ir_codes_em2820) to em2820-input.c
- IR struct renamed and moved to a header file.
- New file to handle em2820-specific IR.
- Some cleanups.
- attach now detects I2C IR and calls em2820-specific IR code
- IR compat code moved to compat.h
- New header with struct IR_i2c there, to allow it to be
used by board-specific input handlers.
- Some improvements at em28xx board detection:
- Board detection message improved to show interface and class.
- Now it doesn't touch audio interfaces.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Include newer I2C ID at ../linux/include/media/id.h:
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Added analog support for ATI HDTV Wonder
Signed-off-by: Kirk Lapray <kirk.lapray@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Set IF of tda8275 according to tv norm.
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Update the tveeprom tuner list with the tuner
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix several redefinitions of i2c IDs. i2c IDs must not be defined
outside of i2c-id.h.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Henk Vergonet <henk@god.dyndns.org>
Acked-by: Mark McClelland <mark@alpha.dyndns.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Include saa6588 compiler option and files.
- Fix comment on tuner.h
- linux/utsname.h replaced by linux/version.h to compile on vanilla 2.6.13
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove $Id CVS logs for V4L files
- Included newer cards.
- Added a new NEC protocol for ir based on pulse distance.
- Enable ATSC support for DViCO FusionHDTV5 Gold.
- Added tuner LG NTSC (TALN mini series).
- Fixed tea5767 autodetection.
- Resolve more tuner types.
- Commented debug function removed from mainstream.
- Remove comments from mainstream. Still on development tree.
- linux/version dependencies removed.
- BTSC Lang1 now is set to auto_stereo mode.
- New tuner standby API.
- i2c-core.c uses hexadecimal for the i2c address, so it should stay consistent.
Signed-off-by: Uli Luckas <luckas@musoft.de>
Signed-off-by: Mac Michaels <wmichaels1@earthlink.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Hermann Pitton <hermann.pitton@onlinehome.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all #include <linux/version.h> and all references to LINUX_VERSION_CODE
and KERNEL_VERSION. Based on patch by Olaf Hering.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In theory, there should be no more users of I2C_ALGO_* at this point.
However, it happens that several drivers were using I2C_ALGO_* for
adapter ids, so we need to correct these before we can get rid of all
the I2C_ALGO_* definitions.
Note that this also fixes a bug in media/video/tvaudio.c:
/* don't attach on saa7146 based cards,
because dedicated drivers are used */
if ((adap->id & I2C_ALGO_SAA7146))
return 0;
This test was plain broken, as it would succeed for many more adapters
than just the saa7146: any those id would share at least one bit with
the saa7146 id. We are really lucky that the few other adapters we want
this driver to work with did not fulfill that condition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Fixed some bttv card numbers.
- BTTV and SAA7134 version numbers incremented to reflect changes.
- pci_dma_supported() is called after pci_set_dma_mask() which
already did check that for us. This patch removes the unneeded call to
pci_dma_supported() at bttv-driver.c
- Ensure a sufficient I2C bus idle time between 2 messages for
saa7134-i2c.c
- It is important to write at first to MO_GP3_IO for cx88-tvaudio.c
- Use try_to_freeze() instead of refrigerator at msp3400.c
- Recognizing the MFPE05-2 Tuner at tveeprom.c
- Add new parameter to help identify radio chipsets at tuner module:
show_i2c=1 will show 16 reading bytes from detected tuners.
- BTTV does generate some Unimplemented IOCTL log at tuner module:
0x40046d11(dir=1,tp=0x6d,nr=17,sz=4) means that it is sending
MSP3400 calls to non-msp3400 tuners. Warning eliminated.
VIDIOSAUDIO is also called, so debug messages updated. It is still
requiring IOCTL implementation.
- Added two more tuners.
- Add support for the SVideo input on the GDI Black Gold.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Graham Bevan <graham.bevan@ntlworld.com>
Signed-off-by: Torsten Seeboth <Torsten.Seeboth@t-online.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t.online.de>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make two needlessly global structs static
- #if 0 the EXPORT_SYMBOL'ed but unused function tveeprom_dump
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fixed a trouble on tuner-core that generates erros on computers with more
than one TV card.
- Rename tuner structures fields.
- Tail spaces removed.
- I2C cleanups and converged to a basic reference structure.
- Removed unused structures.
- Fix setting frequency on tda8290.
- Added code for TEA5767 autodetection.
- Standby mode support implemented. It is used to disable
a non used tuner. Currenlty implemented on tea5767.
- New macro: set_type disables other tuner when changing mode.
- Some cleanups.
- Use 50 kHz step when tunning radio for most tuners to improve precision.
Signed-off-by: Fabien Perrot <perrot1983@yahoo.fr>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-By: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add new Typhoon DVB-T Cardbus.
- DVB-T support for MD7134 cardbus and the PCI variants
- initial DVB-T support for Lifeview Flydvb-t duo
- DVB-T support for Philips TOUGH reference design
- Don't turn off the xtal output of tda8274/75 in sleep mode
- Let Kconfig decide whether to include frontend-specific code in saa7134-dvb.
- Removed unused structures.
Signed-off-by: Juergen Orschiedt <jorschiedt@web.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
*tuner-core.c:
- some tuner_info msgs will be generated only if insmod opt
tuner_debug enabled.
- Implemented tuner-core support for VIDIO_S_TUNER to allow
changing mono/stereo mode
- Remove unneeded config options.
- I2C_CLIENT_MULTI option removed.
- support for Philips FMD12ME hybrid tuner
- allow to initialize with another tuner
- Move PHILIPS_FMD initialization code to set_type function,
* tda8290:
- Fix dumb error in tda8290 tunning.
- Radio tuner uses high-precision step instead of 62.5 KHz.
*tea5767.c:
- tuner_info msgs will be generated only if insmod tuner option
tuner_debug enabled.
- some cleanups for better reading.
- Radio tuner uses high-precision step instead of 62.5 KHz.
- Changing radio mode stereo/mono for tea5767 working.
*tuner-simple.c:
- TNF9533-D/IF UHF fixup.
- Radio tuners now uses high-precision step instead of 62.5 KHz.
*mt20xx.c:
- Radio tuner uses high-precision step instead of 62.5 KHz.
*tda9887.c:
- tab and blank spaces corrections.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Nickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for various SAA7134 cards and brings some fixes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Fabrice Aeschbacher <fabrice.aeschbacher@laposte.net>
Signed-off-by: Hermann Pitton <hermann.pitton@onlinehome.de>.
Signed-off-by: Nickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tuner improvements and additions. TEA5767 FM tuner added. Several small
fixes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Nickolay V Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch adds support for the PixelView Ultra Pro video capture
card in v4l.
- It removes the remote control key definitions from ir-kbd-gpio.c and
moves them to ir-common.c so that they can be shared between bt878 and
cx88 based cards.
- The patch also moves the FUSIONHDTV_3_GOLD_Q card from number 27 to 28
to regain compatibility with the V4L cvs.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
tuner-core.c, tuner.h:
- tuner-core changed to support multiple I2C devices used on some
adapters;
- Kconfig now has an option (CONFIG_TUNER_MULTI_I2C) to enable this new
behavor;
- By default, even enabling CONFIG_TUNER_MULTI_I2C, tuner-core emulates
the old behavor, using first I2C device for both FM and TV;
- There is a new i2c command (TUNER_SET_ADDR) to allow tuner clients to
select I2C address for FM or TV tuner;
- Tuner I2C dettach now generates a warning on syslog if failed.
tuner-simple.c:
- TVision TVF-8531MF and TVF-5533 MF tuner included. It uses, by
default, I2C on 0xC2 address for TV and on 0xC0 for Radio. Both TV and
FM Radio mode are working.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modified dvb_register_adapter() to avoid kmalloc/kfree. Drivers have to embed
struct dvb_adapter into their private data struct from now on. (Andreas
Oberritter)
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
