This patch fixes the follwing build failure on powerpc:-
> Today's linux-next build (powerpc allyesconfig) failed like this:
>
> drivers/regulator/userspace-consumer.c:43: error: conflicting types
> for 'show_state'
> include/linux/sched.h:273: note: previous definition of 'show_state'
> was here
>
> Caused by commit 5defa2bce704ca4151cfe24e4297aa7797cafd22 ("regulator:
> add userspace-consumer driver") which I have reverted for today.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.
The chip is controlled through the I2C bus.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mlx4: Add strong ordering to local inval and fast reg work requests
IB/ehca: Remove superfluous bitmasks from QP control block
RDMA/cxgb3: Limit fast register size based on T3 limitations
RDMA/cxgb3: Report correct port state and MTU
mlx4_core: Add module parameter for number of MTTs per segment
IB/mthca: Add module parameter for number of MTTs per segment
RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
infiniband: Remove void casts
IB/ehca: Increment version number
IB/ehca: Remove unnecessary memory operations for userspace queue pairs
IB/ehca: Fall back to vmalloc() for big allocations
IB/ehca: Replace vmalloc() with kmalloc() for queue allocation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits)
atmel-mci: add MCI2 register definitions
atmel-mci: Integrate AT91 specific definition in header file
tmio_mmc: allow compilation for ASIC3
mmc_block: do not DMA to stack
sdhci: Print ADMA status and pointer on debug
tmio_mmc: fix clock setup
tmio_mmc: map SD control registers after enabling the MFD cell
tmio_mmc: correct probe return value for num_resources != 3
tmio_mmc: don't use set_irq_type
tmio_mmc: add bus_shift support
MFD,mmc: tmio_mmc: make HCLK configurable
mmc_spi: don't use EINVAL for possible transmission errors
cb710: more cleanup for the DEBUG case.
sdhci: platform driver for SDHCI
mxcmmc: remove frequency workaround
cb710: handle DEBUG define in Makefile
cb710: add missing parenthesis
cb710: fix printk format string
mmc: Driver for CB710/720 memory card reader (MMC part)
pxamci: add regulator support.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix inverted wheel for bluetooth version of apple mighty mouse
HID: no more reinitializtion is needed in post_reset
HID: hidraw -- fix comment about accepted devices
HID: Multitouch support for the N-Trig touchscreen
HID: add new multitouch and digitizer contants
HID: autocentering support for Logitech Force 3D Pro
HID: fix hid-ff drivers so that devices work even without ff support
HID: force feedback support for SmartJoy PLUS PS2/USB adapter
HID: Wacom Graphire Bluetooth driver
HID: autocentering support for Logitech G25 Racing Wheel
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice. Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time. This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice. Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.
Reported-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New revision of Atmel MCI interface adds new features. This is a update of
register definition in header file. This new MCI IP is called MCI2.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The MCI IP is shared among AVR32 and AT91 SOCs.
AT91 has specific bit definitions in the user interface of MCI SD/MMC IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
In the write recovery routine, the data to get from the card
is allocated from the stack. The DMA mapping documentation says
explicitly stack memory is not mappable by any of the DMA calls.
Change to using kmalloc() to allocate the memory for the result
from the card and then free it once we've finished with the
transaction.
[ Changed to GFP_KERNEL allocation - Pierre Ossman ]
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
If using ADMA, then we should print the ADMA error
and current pointer in sdhci_dumpregs() when any
debug is requested.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch fixes the clock setup in tmio_mmc.
* Incorrect divider setting
* Cruft written to the clock registers (seemingly harmless but Not
Good (tm))
It also eliminates some unnecessary ifs and tidies the loop syntax.
Thanks to Philipp Zabel who discovered the divider issue, commenting
"Except for the SDCLK = HCLK (divider bypassed) case, the clock
setting resulted in double the requested frequency.
The smallest possible frequency (f_max/512) is configured with
a divider setting 0x80, not 0x40."
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
ASIC3 can disable the memory, so we need to wait for mfd_cell->enable
to enable the memory before we can map the SD control registers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Use an IRQF_TRIGGER_ flag in request_irq instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Added a platform driver which uses the SDHCI core.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Changes pxamci.c to use the regulator subsystem. Uses the regulator case
CONFIG_REGULATOR is defined and a matching is regulator is provided, or
falls back to pdata->setpower otherwise. A warning is displayed case
both a valid regulator and pdata is set, and the regulator is used.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because of granularity issues, sometimes we told the hardware to change
to the voltage we were already at. Rework the logic so this doesn't
happen.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
A pointer to mmc_omap_probe which lives in .init.text is passed to the
core via platform_driver_register and so the kernel might oops if probe
is called after the init code is discarded.
As requested by David Brownell platform_driver_probe is used instead of
moving the probe function to .devinit.text. This saves some memory, but
might have the downside that a device being registered after the call to
mmc_omap_init but before the init sections are discarded will not be
bound anymore to the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Speedup for slow cards by transfering more data at once.
This patch also reduces the amount of wear-out of the flash
blocks because fewer partial blocks are written.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix oops on unaligned user access
avr32: Add support for Mediama RMTx add-on board for ATNGW100
avr32: Change Atmel ATNGW100 config to add choice of add-on board
Fix MIMC200 board LCD init
avr32: Fix clash in ATMEL_USART_ flags
avr32: remove obsolete hw_interrupt_type
avr32: Solves problem with inverted MCI detect pin on Merisc board
atmel-mci: Add support for inverted detect pin
* 'next-i2c' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-ocores: Can add I2C devices to the bus
i2c-s3c2410: move to using platform idtable to match devices
i2c: OMAP3: Better noise suppression for fast/standard modes
i2c: OMAP2/3: Fix scll/sclh calculations
i2c: Blackfin TWI: implement I2C_FUNC_SMBUS_I2C_BLOCK functionality
i2c: Blackfin TWI: fix transfer errors with repeat start
i2c: Blackfin TWI: fix REPEAT START mode doesn't repeat
i2c: Blackfin TWI: make sure we don't end up with a CLKDIV=0
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (35 commits)
hwrng: timeriomem - Fix potential oops (request_mem_region/__devinit)
crypto: api - Use formatting of module name
crypto: testmgr - Allow hash test vectors longer than a page
crypto: testmgr - Check all test vector lengths
crypto: hifn_795x - fix __dev{init,exit} markings
crypto: tcrypt - Do not exit on success in fips mode
crypto: compress - Return produced bytes in crypto_{,de}compress_{update,final}
hwrng: via_rng - Support VIA Nano hardware RNG on X86_64 builds
hwrng: via_rng - Support VIA Nano hardware RNG
hwrng: via_rng - The VIA Hardware RNG driver is for the CPU, not Chipset
crypto: testmgr - Skip algs not flagged fips_allowed in fips mode
crypto: testmgr - Mark algs allowed in fips mode
crypto: testmgr - Add ctr(aes) test vectors
crypto: testmgr - Dynamically allocate xbuf and axbuf
crypto: testmgr - Print self-test pass notices in fips mode
crypto: testmgr - Catch base cipher self-test failures in fips mode
crypto: testmgr - Add ansi_cprng test vectors
crypto: testmgr - Add infrastructure for ansi_cprng self-tests
crypto: testmgr - Add self-tests for rfc4309(ccm(aes))
crypto: testmgr - Handle AEAD test vectors expected to fail verification
...
drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
make[1]: *** [drivers/net/cnic.o] Error 1
make: *** [drivers/net/cnic.o] Error 2
Caused by not including linux/module.h
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix cnic build for case of CONFIG_INET=n.
Fix cnic build for case of CONFIG_IPV6=m and CONFIG_CNIC=y.
Fixes these build errors:
cnic.c:(.text+0x236a1d): undefined reference to `ip_route_output_key'
cnic.c:(.text+0x15a8e8): undefined reference to `ip6_route_output'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.
OMAP3430 TRM gives the following equations:
F/S: tLow = (scll + 7) * internal_clk
tHigh = (sclh + 5) * internal_clk
HS: tLow = (scll + 7) * fclk
tHigh = (sclh + 5) * fclk
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
speed tLow tHigh
3400 160 ns 60 ns
1700 320 ns 120 ns
and for F/S:
speed tLow tHigh
400 1300 ns 600 ns
100 4700 ns 4000 ns
By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
