This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dynamic ITR algorithm depends on a calculation of usecs which
assumes that the interrupts have been firing constantly at the interrupt
throttle rate. This is not guaranteed because we could have a low packet
rate, or have been polling in software.
We'll estimate whether this is the case by using jiffies to determine if
we've been too long. If the time difference of jiffies is larger we are
guaranteed to have an incorrect calculation. If the time difference of
jiffies is smaller we might have been polling some but the difference
shouldn't affect the calculation too much.
This ensures that we don't get stuck in BULK latency during certain rare
situations where we receive bursts of packets that force us into NAPI
polling.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit c56625d597 ("i40e/i40evf: change dynamic interrupt
thresholds") a new higher latency ITR setting called I40E_ULTRA_LATENCY
was added with a cryptic comment about how it was meant for adjusting Rx
more aggressively when streaming small packets.
This mode was attempting to calculate packets per second and then kick
in when we have a huge number of small packets.
Unfortunately, the ULTRA setting was kicking in for workloads it wasn't
intended for including single-thread UDP_STREAM workloads.
This wasn't caught for a variety of reasons. First, the ip_defrag
routines were improved somewhat which makes the UDP_STREAM test still
reasonable at 10GbE, even when dropped down to 8k interrupts a second.
Additionally, some other obvious workloads appear to work fine, such
as TCP_STREAM.
The number 40k doesn't make sense for a number of reasons. First, we
absolutely can do more than 40k packets per second. Second, we calculate
the value inline in an integer, which sometimes can overflow resulting
in using incorrect values.
If we fix this overflow it makes it even more likely that we'll enter
ULTRA mode which is the opposite of what we want.
The ULTRA mode was added originally as a way to reduce CPU utilization
during a small packet workload where we weren't keeping up anyways. It
should never have been kicking in during these other workloads.
Given the issues outlined above, let's remove the ULTRA latency mode. If
necessary, a better solution to the CPU utilization issue for small
packet workloads will be added in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 96db776a36 ("i40e/vf: fix interrupt affinity bug")
we added some code to force exit of polling in case we did
not have the correct CPU. This is important since it was possible for
the IRQ affinity to be changed while the CPU is pegged at 100%. This can
result in the polling routine being stuck on the wrong CPU until
traffic finally stops.
Unfortunately, the implementation, "if the CPU is correct, exit as
normal, otherwise, fall-through to the end-polling exit" is incredibly
confusing to reason about. In this case, the normal flow looks like the
exception, while the exception actually occurs far away from the if
statement and comment.
We recently discovered and fixed a bug in this code because we were
incorrectly initializing the affinity mask.
Re-write the code so that the exceptional case is handled at the check,
rather than having the logic be spread through the regular exit flow.
This does end up with minor code duplication, but the resulting code is
much easier to reason about.
The new logic is identical, but inverted. If we are running on a CPU not
in our affinity mask, we'll exit polling. However, the code flow is much
easier to understand.
Note that we don't actually have to check for MSI-X, because in the MSI
case we'll only have one q_vector, but its default affinity mask should
be correct as it includes all CPUs when it's initialized. Further, we
could at some point add code to setup the notifier for the non-MSI-X
case and enable this workaround for that case too, if desired, though
there isn't much gain since its unlikely to be the common case.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we don't have MSI-X enabled, we handle interrupts on all icr0. This
is a special case, so let's move the conditional into
i40e_update_enable_itr() in order to make i40e_napi_poll easier to
read about.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit hosts and with CONFIG_DEBUG_LOCK_ALLOC we should be seeing a
lockdep splat indicating this seqcount is not correctly initialized, fix
that.
Fixes: 980e9b1186 ("i40e: Add support for 64 bit netstats")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiler reported several places where driver compared
signed and unsigned types. Cast or change the types to remove
the warnings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This just reorders some local vars and makes the code flow
clearer.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds proper XDP_TX action support. For each Tx ring, an
additional XDP Tx ring is allocated and setup. This version does the
DMA mapping in the fast-path, which will penalize performance for
IOMMU enabled systems. Further, debugfs support is not wired up for
the XDP Tx rings.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This commit adds basic XDP support for i40e derived NICs. All XDP
actions will end up in XDP_DROP.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent commit to refactor the driver and remove the hw_disabled_flags
field accidentally introduced two regressions. First, we overwrote
pf->flags which removed various key flags including the MSI-X settings.
Additionally, it was intended that we have now two flags,
HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done,
and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere.
This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely
updates pf->flags instead of overwriting it.
Without this patch we will have many problems including disabling MSI-X
support, and we'll attempt to use HW ATR eviction on devices which do
not support it.
Fixes: 47994c119a ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.
Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.
Fixes: f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.
It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.
Add an i40e_ptp_tx_hang() function similar to the already existing
i40e_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.
Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.
There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver uses a bit lock to indicate when a Tx timestamp is in
progress to avoid attempting to timestamp multiple packets at once. This
is required because hardware only has registers to handle one request at
a time.
There is a corner case where we failed to cleanup the bit lock after
a failed transmit. This can potentially result in a state bit being
locked forever.
Add some cleanup code to i40e_xmit_frame_ring to check and make sure we
cleanup incase of these failures. We also modify i40e_tx_map to return
an error code indication DMA failure.
Reported-by: Reported-by: David Mirabito <davidm@metamako.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hw_disabled_flags field was added as a way of signifying that
a feature was automatically or temporarily disabled. However, we
actually only use this for FDir features. Replace its use with new
_AUTO_DISABLED flags instead. This is more readable, because you aren't
setting an *_ENABLED flag to *disable* the feature.
Additionally, clean up a few areas where we used these bits. First, we
don't really need to set the auto-disable flag for ATR if we're fully
disabling the feature via ethtool.
Second, we should always clear the auto-disable bits in case they somehow
got set when the feature was disabled. However, avoid displaying
a message that we've re-enabled the feature.
Third, we shouldn't be re-enabling ATR in the SB ntuple add flow,
because it might have been disabled due to space constraints. Instead,
we should just wait for the fdir_check_and_reenable to be called by the
watchdog.
Overall, this change allows us to simplify some code by removing an
extra field we didn't need, and the result should make it more clear as
to what we're actually doing with these flags.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of assuming our flags fit within an unsigned long, use
DECLARE_BITMAP which will ensure that we always allocate enough space.
Additionally, use __I40E_STATE_SIZE__ markers as the last element of the
enumeration so that the size of the BITMAP is compile-time assigned
rather than programmer-time assigned. This ensures that potential future
flag additions do not actually overrun the array. This is especially
important as 32bit systems would only have 32bit longs instead of 64bit
longs as we generally have assumed in the prior code.
This change also removes a dereference of the state fields throughout
the code, so it does have a bit of code churn. The conversions were
automated using sed replacements with an alternation
s/&(vsi->back|vsi|pf)->state/\1->state/
s/&adapter->vsi.state/adapter->vsi.state/
For debugfs, we modify the printing so that we can display chunks of the
state value on new lines. This ensures that we can print the entire set
of state values. Additionally, we now print them as 08lx to ensure that
they display nicely.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid using the same named flags for both vsi->state and pf->state. This
makes code review easier, as it is more likely that future authors will
use the correct state field when checking bits. Previous commits already
found issues with at least one check, and possibly others may be
incorrect.
This reduces confusion as it is more clear what each flag represents,
and which flags are valid for which state field.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds tracepoints to the i40e and i40evf drivers to which
BPF programs can be attached for feature testing and verification.
It's expected that an attached BPF program will identify and count or
log some interesting subset of traffic. The bcc-tools package is
helpful there for containing all the BPF arcana in a handy Python
wrapper. Though you can make these tracepoints log trace messages, the
messages themselves probably won't be very useful (other to verify the
tracepoint is being called while you're debugging your BPF program).
The idea here is that tracepoints have such low performance cost when
disabled that we can leave these in the upstream drivers. This may
eventually enable the instrumentation of unmodified customer systems
should the need arise to verify a NIC feature is working as expected.
In general this enables one set of feature verification tools to be
used on these drivers whether they're built with the kernel or
separately.
Users are advised against using these tracepoints for anything other
than a diagnostic tool. They have a performance impact when enabled,
and their exact placement and form may change as we see how well they
work in practice for the purposes above.
Change-ID: Id6014a7322c0e6d08068114dd20bd156f2f6435e
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue I introduced when I converted the code over to
using the length field to determine if a descriptor was done or not. It
turns out that we are also processing programming descriptors in the Rx
path and need to have these processed even though the length field will be
0 on these packets. What will happen with a programming descriptor is that
we will receive a descriptor that has the SPH bit set, and the header
length and packet length fields cleared.
To account for this we should be checking for the bit for split header
being set even though we aren't actually using header split. This bit is
set in the length field to indicate if a programming descriptor response is
contained in the descriptor. Since we don't support header split we don't
need to perform the extra checks of using a fixed value for the entire
length field.
In addition I am moving the function for checking if a filter is a
programming status filter into the i40e_txrx.c file since there is no
longer support for FCoE it doesn't make sense to keep this file in i40e.h.
Change-ID: I12c359c3dc70adb9d6b92b27324bb2c7f04c1a06
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to improve the performance of the Rx path.
Specifically by using build_skb we have several distinct advantages.
In the case of small frames we were previously using a copy-break approach.
This means that we were allocating a page fragment to use for skb->head,
and were having to copy the packet into that region. Both of those calls
are now avoided since we just build the skb around the data.
In the case of large frames the gains are much more significant.
Specifically we were having to allocate skb->head, and copy the headers as
before. However in addition we were having to parse the header using
eth_get_headlen which could be quite expensive. All of this is avoided by
building the frame around the data. I have seen gains as high as 30% when
using VXLAN for instance due to just header pulling overhead.
Finally with all this in place it also sets us up to start looking at
enabling XDP. Specifically we now have a path in which the data is in the
page and the frame is built around it. So if we parse it with XDP before
we call build_skb we can take care of any necessary processing there.
Change-ID: Id4bdd618e94473d41f892417e5d8019639e421e3
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds padding to the start of frames to make room for headroom
for us to eventually start using build_skb. Right now we guarantee at
least NET_SKB_PAD + NET_IP_ALIGN, however we allocate more space if more is
available. For example on x86 the headroom should be 192 bytes.
On systems that have too large of a cache line size to support storing 1.5K
padding and shared info we default to using 3K buffers and reserve
everything that isn't used for skb_shared_info or the data buffer for
headroom.
Change-ID: I33c641c9a1ea10cf7cc484c2d20985368d2d709a
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are situations where adding padding to the front and back of an Rx
buffer will require that we add additional padding. Specifically if
NET_IP_ALIGN is non-zero, or the MTU size is larger than 7.5K we would need
to use 2K buffers which leaves us with no room for the padding.
To preemptively address these cases I am adding support for 3K buffers to
the Rx path so that we can provide the additional padding needed in the
event of NET_IP_ALIGN being non-zero or a cache line being greater than 64.
Change-ID: I938bc1ba611285428df39a613cd66f98e60b55c7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch greatly reduces the unneeded complexity in the
i40e_detect_recover_hung_queue code path. The previous implementation
set a 'hung bit' which would then get cleared while polling. If the
detection routine was called a second time with the bit already set, we
would issue a software interrupt. This patch makes it such that if
interrupts are disabled and we have pending TX descriptors, we trigger a
software interrupt since in, the worst case, queues are already clean
and we have an extra interrupt.
Additionally this patch removes the workaround for lost interrupts as
calling napi_reschedule in this context can cause software interrupts to
fire on the wrong CPU.
Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a minor cleanup so that we are always updating pf->flags when we
make a change to the private flags instead of updating a mix of either
pf->flags and/or pf->hw_disabled_flags.
In addition I went through and cleaned out all the spots where we were
using the X722 define in regards to this flag.
Lastly since we changed the logic I went through and flushed out any
redundancy and cleaned up the handling of the flags in the Tx path.
Change-ID: I79ff95a7272bb2533251ff11ef91e89ccb80b610
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Re-word the error message displayed when adding a filter with an
invalid flow type. Additionally, report a distinct error message when
the IPv4 protocol is at fault.
Change-ID: Iba3d85b87f8d383c97c8bdd180df34a6adf3ee67
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to clean up the code in preparation for us adding
support for build_skb. Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.
Specifically with this change we split out the code for adding a page to an
exiting skb.
Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions. This allows us
to commonize the bits that handle either freeing or recycling the buffers.
As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer. It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.
Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.
The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer. We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.
Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a minor clean-up to make the i40e/i40evf process_skb_fields
function look a little more like what we have in igb. The Rx checksum
function called out a need for skb->protocol but I can't see where it
actually needs it. I am assuming this is something that was likely
refactored out some time ago as the Rx checksum code has gone through a few
rewrites.
Change-ID: I0b4668a34d90b61b66ded7c7c26e19a3e2d06251
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to reset skb back to NULL when we have freed it in the Rx cleanup
path. I found one spot where this wasn't occurring so this patch fixes it.
Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
I also found and fixed a store forwarding stall from where we were
assigning "*new_buff = *old_buff". By breaking it up into individual
copies we can avoid this and as a result the performance is slightly
improved.
Change-ID: I1d3880dece4133eca3c32423b04a5467321ccc52
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable FDir filters for SCTPv4 packets using the ethtool ntuple
interface to enable filters. The ethtool API does not allow masking on
the verification tag.
Change-Id: I093e88a8143994c7e6f4b7b17a0bd5cf861d18e4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for flexible payloads passed via ethtool user-def field.
This support is somewhat limited due to hardware design. The input set
can only be programmed once per filter type, and the flexible offset is
part of this filter input set. This means that the user cannot program
both a regular and a flexible filter at the same time for a given flow
type. Additionally, the user may not program two flexible filters of the
same flow type with different offsets, although they are allowed to
configure different values at that offset location.
We support a single flexible word (2byte) value per protocol type, and
we handle the FLX_PIT register using a list of flexible entries so that
each flow type may be configured separately.
Due to hardware implementation, the flexible data is offset from the
start of the packet payload, and thus may not be in part of the header
data. For this reason, the offset provided by the user defined data is
interpreted as a byte offset from the start of the matching payload.
Previous implementations have tried to represent the offset as from the
start of the frame, but this is not feasible because header sizes may
change due to options.
Change-Id: 36ed27995e97de63f9aea5ade5778ff038d6f811
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move ATR exit check after we have sent the TCP/IPv4 filter to the ring
successfully. This avoids an issue where we potentially update the
filter count without actually succeeding in adding the filter. Now, we
only increment the fd_tcp_rule after we've succeeded. Additionally, we
will re-enable ATR mode only after deletion of the filter is actually
posted to the FDIR ring.
Change-ID: If5c1dea422081cc5e2de65618b01b4c3bf6bd586
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of setting err=true and checking this to determine when to free
the raw_packet near the end of the function, simply kfree and return
immediately. The resulting code is a bit cleaner and has one less
variable. This also resolves a subtle bug in the ipv4 case which could
fail to add the first filter and then never free the memory, resulting
in a small memory leak.
Change-ID: I7583aac033481dc794b4acaa14445059c8930ff1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code originally included src_ip and dst_ip with enough space to
support ipv6 filters. However, no actual support for ipv6 filters has
been implemented. Thus, remove the arrays and just use __be32 values.
Should ipv6 support be added in the future, we can replace these with
a union that has sizes for both values.
Change-Id: I1bc04032244a80eb6ebc8a4e6c723a4a665c1dd5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.
Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we
are able to see performance improvements on architectures that implement
either one due to the fact that page mapping and unmapping only has to
sync what is actually being used instead of the entire buffer. In addition
by enabling the weak ordering attribute enables a performance improvement
for architectures that can associate a memory ordering with a DMA buffer
such as Sparc.
Change-ID: If176824e8231c5b24b8a5d55b339a6026738fc75
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix, or rather, avoid a sparse warning caused by the fact that
csum_replace_by_diff expects to receive a __wsum value. Since the
calculation appears to work, simply typecast the passed paylen value to
__wsum to avoid the warning.
This seems pretty fishy since __wsum was obviously annotated as
a separate type on purpose, so this throws the entire calculation into
question. Since it currently appears to behave as expected, the typecast
is probably safe.
Change-ID: I4fdc5cddd589abc16098176e8a61127e761488f4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a bug introduced with the addition of the per queue
ITR feature support in ethtool. With that addition, there were
functions added which converted the ITR settings to binary values.
The IS_ENABLED macros that run on those values check whether a bit
is set or not and with the value being binary, the bit check always
returned ITR disabled which prevents any updating of the ITR rate.
This patch fixes the problem by changing the functions to return the
current ITR value instead and renaming it to better reflect
its function. These functions now provide a value which will be
accurately asessed and update the ITR as intended.
Change-ID: I14f1d088d052e27f652aaa3113e186415ddea1fc
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original comment implies that the only location where the raw_packet
buffer will be freed is in i40e_clean_tx_ring() which is incorrect. In
fact this isn't even the normal case. Update the comment explaining
where the memory is freed.
Change-ID: Ie0defc35ed1c3af183f81fdc60b6d783707a5595
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reorganize the i40e_pull_tail() logic, doing it in i40e_add_rx_frag()
where it's cheaper. The igb driver does this the same way.
Also renames i40e_page_is_reserved() to reflect what it actually
tests.
Change-ID: Icd9cc507aae1fcdc02308b3a09034111b4c24071
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reduces the size of struct i40e_rx_buffer by one pointer,
and makes the i40e driver a little more consistent with the igb driver
in terms of packets that span buffers.
We do this by moving the skb field from struct i40e_rx_buffer to
struct i40e_ring. We pass the skb we already have (or NULL if we
don't) to i40e_fetch_rx_buffer(), which skips the skb allocation if we
already have one for this packet.
Change-ID: I4ad48a531844494ba0c5d8e1a62209a057f661b0
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On packet RX, we perform a DMA sync for CPU before passing the
packet up. Here we limit that sync to the actual length of the
incoming packet, rather than always syncing the entire buffer.
Change-ID: I626aaf6c37275a8ce9e81efcaa773f327b331487
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does some quick work to pull some of the data off of the stack
and hopefully start storing it in the Tx buffer info section of the Tx
ring. Ideally we should be moving away from having to store much of
anything on the stack and can just maintain it all in the descriptor rings.
Change-ID: I4b4715ea1920e122502482b3f9e56a9a6cb1e9fe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the function i40e_napi-poll() returns 0 when it clean completely
the Rx rings, but this foul budget accounting in core code.
Fix this by returning the actual work done, capped to budget - 1, since
the core doesn't allow to return the full budget when the driver modifies
the NAPI status
This is based on a similar change that was made for the ixgbe driver by
Paolo Abeni.
Change-ID: Ic3d93ad2fa2fc8ce3164bc461e69367da0f9173b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reorders the logic at the end of i40e_tx_map to address the
fact that the logic was rather convoluted and much larger than it needed
to be.
In order to try and coalesce the code paths I have updated some of the
comments and repurposed some of the variables in order to reduce
unnecessary overhead.
This patch does the following:
1. Quit tracking skb->xmit_more with a flag, just max out packet_stride
2. Drop tail_bump and do_rs and instead just use desc_count and td_cmd
3. Pull comments from ixgbe that make need for wmb() more explicit.
Change-ID: Ic7da85ec75043c634e87fef958109789bcc6317c
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a common method for finding a VSI by type. The main
motivation for doing this is that the Flow Director path actually had two
ways of handling this, one stopped on first match and one did not. This
patch makes it so that all callers of this function will get the same
approach for finding a VSI.
Change-ID: Ibf25de8acd8466582520694424aa87da66965fbd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current Rx timestamp hang logic is not very robust because it does
not notice a register is hung until all four timestamps have been
latched and we wait a full 5 seconds. Replace this logic with a newer Rx
hang detection based on storing the jiffies when we first notice
a receive timestamp event. We store each register's time separately,
along with a flag indicating if it is currently latched. Upon first
transitioning to latch, we will update the latch_events[i] jiffies
value. This indicates the time we first noticed this event. The watchdog
routine will simply check that the either the flag has been cleared, or
we have passed at least one second. In this case, it is able to clear
the Rx timestamp register under the assumption that it was for a dropped
frame. The benefit if this strategy is that we should be able to
detect and clear out stalled RXTIME_H registers before we exhaust the
supply of 4, and avoid complete stall of Rx timestamp events.
Change-ID: Id55458c0cd7a5dd0c951ff2b8ac0b2509364131f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When hardware has taken a timestamp for a received packet, it indicates
which RXTIME register the timestamp was placed in by some bits in the
receive descriptor. It uses 3 bits, one to indicate if the descriptor
index is valid (ie: there was a timestamp) and 2 bits to indicate which
of the 4 registers to read. However, the driver currently does not check
the TSYNVALID bit and only checks the index. It assumes a zero index
means no timestamp, and a non zero index means a timestamp occurred.
While this appears to be true, it prevents ever reading a timestamp in
RXTIME[0], and causes the first timestamp the device captures to be
ignored.
Fix this by using the TSYNVALID bit correctly as the true indicator of
whether the packet has an associated timestamp.
Also rename the variable rsyn to tsyn as this is more descriptive and
matches the register names.
Change-ID: I4437e8f3a3df2c2ddb458b0fb61420f3dafc4c12
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up several pieces of redundant code in the Rx clean-up
paths.
The first bit is that hdr_addr and the status_err_len portions of the Rx
descriptor represent the same value. As such there is no point in setting
them to 0 before setting them to 0. I'm dropping the second spot where we
are updating the value to 0 so that we only have 1 write for this value
instead of 2.
The second piece is the checking for the DD bit in the packet. We only
need to check for a non-zero value for the status_err_len because if the
device is done with the descriptor it will have written something back and
the DD is just one piece of it. In addition I have moved the reading of
the Rx descriptor bits related to rx_ptype down so that they are actually
below the dma_rmb() call so that we are guaranteed that we don't have any
funky 64b on 32b calls causing any ordering issues.
Change-ID: I256e44a025d3c64a7224aaaec37c852bfcb1871b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in which a 'perfect storm' can occur and cause
interrupts to fail to be correctly affinitized. This causes unexpected
behavior and has a substantial impact on performance when it happens.
The bug occurs if there is heavy traffic, any number of CPUs that have
an i40e interrupt are pegged at 100%, and the interrupt afffinity for
those CPUs is changed. Instead of moving to the new CPU, the interrupt
continues to be polled while there is heavy traffic.
The bug is most readily realized as the driver is first brought up and
all interrupts start on CPU0. If there is heavy traffic and the
interrupt starts polling before the interrupt is affinitized, the
interrupt will be stuck on CPU0 until traffic stops. The bug, however,
can also be wrought out more simply by affinitizing all the interrupts
to a single CPU and then attempting to move any of those interrupts off
while there is heavy traffic.
This patch fixes the bug by registering for update notifications from
the kernel when the interrupt affinity changes. When that fires, we
cache the intended affinity mask. Then, while polling, if the cpu is
pegged at 100% and we failed to clean the rings, we check to make sure
we have the correct affinity and stop polling if we're firing on the
wrong CPU. When the kernel successfully moves the interrupt, it will
start polling on the correct CPU. The performance impact is minimal
since the only time this section gets executed is when performance is
already compromised by the CPU.
Change-ID: I4410a880159b9dba1f8297aa72bef36dca34e830
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We cannot currently support SCTP in the hardware, and IPV4_FLOW is not used
anywhere by the software so we can go through and drop the functionality
related to these two flow types.
In addition we cannot support masking based on the protocol value so if the
user is expecting a value other than TCP or UDP we should simply return an
error rather then trying to allocate a filter for a rule that will only
partially match what the user requested.
Change-ID: I10d52bb97d8104d76255fe244551814ff9531a63
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can reorder the busy wait loop at the start of the Flow Director
transmit function to reduce the overall code size while still retaining the
same functionality. As such I am taking advantage of the opportunity to do
so.
Change-ID: I34c403ca001953c6ac9816e65d5305e73d869026
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit a75e8005d5 ("i40e: queue-specific settings for interrupt
moderation") the i40e driver gained support for setting interrupt
moderation values per queue. This patch adds support for this feature
to the i40evf driver as well. In addition, a few changes are made to
the i40e implementation to add function header documentation comments,
as well.
This behaves in a similar fashion to the implementation in i40e. Thus,
requesting the moderation value when no queue is provided will report
queue 0 value, while setting the value without a queue will set all
queues at once.
Change-ID: I1f310a57c8e6c84a8524c178d44d1b7a6d3a848e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This interface was only ever meant for debug only. Since it is not
supposed to be here we are removing it.
Change-ID: Id771a1e5e7d3e2b4b7f56591b61fb48c921e1d04
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In an effort to improve code readability I am splitting the Flow Director
filter configuration out into a separate function like we have done for the
standard xmit path. The general idea is to provide a single block of code
that translates the flow specification into a proper Flow Director
descriptor.
Change-ID: Id355ad8030c4e6c72c57504fa09de60c976a8ffe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a txring_txq function which allows us to convert a
i40e_ring/i40evf_ring to a netdev_tx_queue structure. This way we
can avoid having to make a multi-line function call for all the spots
that need access to this.
Change-ID: Ic063b71d8b92ea406d2c32e798c8e2b02809d65b
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx cleanup flow was incorrectly assuming it could check for the flow
director bits after it had unmapped the buffer. However in this case it
results in us trying to free a raw_buf as though it is an sk_buff.
To fix this I am moving up the flag test for the FD_SB bit so that when
find a non-NULL skb or raw_buf value we then check the flag and use the
appropriate call to free the buffer.
Change-ID: I6284034ba1ea87c9922e56f6eb3181f7f09bddde
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some locations that disable ATR accidentally used the "full" disable by
disabling the flag in the standard flags field. This incorrectly forces
ATR off permanently instead of temporarily disabling it. In addition,
some code locations accidentally set the ATR flag enabled when they only
meant to clear the auto_disable_flags. This results in ignoring the
user's ethtool private flag settings.
Additionally, when disabling ATR via ethtool, we did not perform a flush
of the FD table. This results in the previously assigned ATR rules still
functioning which was not expected.
Cleanup all these areas so that automatic disable uses only the
auto_disable_flag. Fix the flush code so that we can trigger a flush
even when we've disabled ATR and SB support, as otherwise the flush
doesn't work. Fix ethtool setting to actually request a flush. Fix
NETIF_F_NTUPLE flag to only clear the auto_disable setting and not
enable the full feature.
Change-ID: Ib2486111f8031bd16943e9308757b276305c03b5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver was incorrectly assuming that we would always be pulling
no more than 1 descriptor from each fragment. It is in fact possible for
us to end up with the case where 2 descriptors worth of data may be pulled
when a frame is larger than one of the pieces generated when aligning the
payload to either 4K or pieces smaller than 16K.
To adjust for this we just need to make certain to test all the way to the
end of the fragments as it is possible for us to span 2 descriptors in the
block before us so we need to guarantee that even the last 6 descriptors
have enough data to fill a full frame.
Change-ID: Ic2ecb4d6b745f447d334e66c14002152f50e2f99
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-07-22
This series contains updates to i40e and i40evf.
Heinrich Schuchardt found a possible null pointer being dereferenced in
i40e_debug_aq(), fixed the issue by doing the variable assignment after
we are sure the pointer is not null.
Avinash fixed an issue when link was down, we were not showing the
correct advertised link modes.
Mitch cleans up a useless initializer since the variable is assigned
right away. Refactors the receive filter handling to properly track
filter adds and deletes so the driver will not lose filters during a
reset and up/down cycles. Also added a tracking mechanism so that the
driver knows when to enter and leave promiscuous mode.
Catherine removes a device id which is not needed (or used). Moves
a mutex lock since we need to lock the client list around the
i40e_client_release() call to prevent the release from interrupting
the client instances while they are being added.
Joshua adds Hyper-V specific VF device ids.
Amitoj Kaur Chawla cleans up a redundant memset() call before a memcpy().
Stefan Assmann adds the missing link advertise for some x710 NICs.
Tushar Dave fixes and issue found on SPARC, where a PF reset clears MAC
filters and if a platform-specific MAC address is used, the driver has
to explicitly write default MAC address to MAC filters otherwise all
incoming traffic destined to the default MAC address will be dropped
after reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This initializer isn't needed because the variable is assigned right
away.
Change-ID: I6ce3edb3f4e0364db248a7a0bcc62ca95c01d941
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are a couple of issues I found in i40e_rx_checksum while doing some
recent testing. As a result I have found the Rx checksum logic is pretty
much broken and returning that the checksum is valid for tunnels in cases
where it is not.
First the inner types are not the correct values to use to test for if a
tunnel is present or not. In addition the inner protocol types are not a
bitmask as such performing an OR of the values doesn't make sense. I have
instead changed the code so that the inner protocol types are used to
determine if we report CHECKSUM_UNNECESSARY or not. For anything that does
not end in UDP, TCP, or SCTP it doesn't make much sense to report a
checksum offload since it won't contain a checksum anyway.
This leaves us with the need to set the csum_level based on some value.
For that purpose I am using the tunnel_type field. If the tunnel type is
GRENAT or greater then this means we have a GRE or UDP tunnel with an inner
header. In the case of GRE or UDP we will have a possible checksum present
so for this reason it should be safe to set the csum_level to 1 to indicate
that we are reporting the state of the inner header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for offloading IPXIP6 type packets that represent
either IPv4 or IPv6 encapsulated inside of an IPv6 outer IP header. In
addition with this change we should also be able to support FOU
encapsulated traffic with outer IPv6 headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This logic is inverted. If the RXHASH flag is set, then we should go
ahead and call skb_set_hash.
Change-ID: Ib2e30356dced1d3e939c8061ab6ad5bd94197e7c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is part 1 of the Rx refactor series, just including
changes to i40e.
This refactor aligns the receive routine with the one in
ixgbe which was highly optimized. This reduces the code
we have to maintain and allows for (hopefully) more readable
and maintainable RX hot path.
In order to do this:
- consolidate the receive path into a single function that doesn't
use packet split but *does* use pages for Rx buffers.
- remove the old _1buf routine
- consolidate several routines into helper functions
- remove ethtool control over packet split
Change-ID: I5ca100721de65992aa0114f8b4bac844b84758e0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As part of preparation for the rx-refactor, remove the
packet split receive routine and ancillary code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the interpretation of a tunnel. This removes
some code and lets us start using the hardware's parsing.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that i40e and i40evf can use GSO_PARTIAL to support
segmentation for frames with checksums enabled in outer headers. As a
result we can now send data over these types of tunnels at over 20Gb/s
versus the 12Gb/s that was previously possible on my system.
The advantage with the i40e parts is that this offload is mostly
transparent as the hardware still deals with the inner and/or outer IPv4
headers so the IP ID is still incrementing for both when this offload is
performed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was offloading the VLAN tag into the skb
any time there was a VLAN tag and the hardware stripping was
enabled. Just check to make sure it's enabled before put_tag.
Change-Id: Ife95290c06edd9a616393b38679923938b382241
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the documentation it turns out enabling IPIP and SIT offloads
for i40e is pretty straightforward. As such I decided to enable them with
this patch. In my testing I am seeing an improvement of 8 to 10 Gb/s
for IPIP and SIT tunnels with this offload enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a bug introduced based on my interpretation of the
XL710 datasheet. Specifically section 8.4.1 states that "A single transmit
packet may span up to 8 buffers (up to 8 data descriptors per packet
including both the header and payload buffers)." It then later goes on to
say that each segment for a TSO obeys the previous rule, however it then
refers to TSO header and the segment payload buffers.
I believe the actual limit for fragments with TSO and a skbuff that has
payload data in the header portion of the buffer is actually only 7
fragments as the skb->data portion counts as 2 buffers, one for the TSO
header, and one for a segment payload buffer.
Fixes: 2d37490b82 ("i40e/i40evf: Rewrite logic for 8 descriptor per packet check")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As it turns out, calling into other files from hot path hurts
performance a lot. In this case the majority of the time we
call "check FCoE" and the packet is *not* FCoE, but this call
was taking 5% of our total cycles spent on receive.
Change-ID: I080552c26e7060bc7b78504dc2763f6f0b3d8c76
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of the tx_ring arguments can be deleted since they are not used.
Change-ID: I99275b0f191d7f63ec2f05061919904940c36f31
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A local variable could move down inside the context where it is used.
Change-ID: I9caba9e1eacf921037077f2665cbce83fd8e95d6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With IPv4 and IPv6 now using the same format for checksums based on the
length of the frame we need to update the i40e and i40evf drivers so that
they correctly account for lengths greater than or equal to 64K.
With this patch the driver should now correctly update checksums for frames
up to 16776960 in length which should be more than large enough for all
possible TSO frames in the near future.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simple cast to fix a sparse warning.
Fixes: commit 5453205cd0 ("i40e/i40evf: Enable support for
SKB_GSO_UDP_TUNNEL_CSUM")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk Tx clean for skbs. In order to enable it we need
to pass the napi_budget value as that is used to determine if we are truly
running in NAPI mode or if we are simply calling the routine from netpoll
with a budget of 0. In order to avoid adding too many more variables I
thought it best to pass the VSI directly in a fashion similar to what we do
on igb and ixgbe with the q_vector.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the polling routines for i40e and i40evf we were using bitwise operators
to avoid the side effects of the logical operators, specifically the fact
that if the first case is true with "||" we skip the second case, or if it
is false with "&&" we skip the second case. This fixes an earlier patch
that converted the bitwise operators over to the logical operators and
instead replaces the entire thing with just an if statement since it should
be more readable what we are trying to do this way.
Fixes: 1a36d7fadd ("i40e/i40evf: use logical operators, not bitwise")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
From what I can tell the practical limitation on the size of the Tx data
buffer is the fact that the Tx descriptor is limited to 14 bits. As such
we cannot use 16K as is typically used on the other Intel drivers. However
artificially limiting ourselves to 8K can be expensive as this means that
we will consume up to 10 descriptors (1 context, 1 for header, and 9 for
payload, non-8K aligned) in a single send.
I propose that we can reduce this by increasing the maximum data for a 4K
aligned block to 12K. We can reduce the descriptors used for a 32K aligned
block by 1 by increasing the size like this. In addition we still have the
4K - 1 of space that is still unused. We can use this as a bit of extra
padding when dealing with data that is not aligned to 4K.
By aligning the descriptors after the first to 4K we can improve the
efficiency of PCIe accesses as we can avoid using byte enables and can fetch
full TLP transactions after the first fetch of the buffer. This helps to
improve PCIe efficiency. Below is the results of testing before and after
with this patch:
Recv Send Send Utilization Service Demand
Socket Socket Message Elapsed Send Recv Send Recv
Size Size Size Time Throughput local remote local remote
bytes bytes bytes secs. 10^6bits/s % S % U us/KB us/KB
Before:
87380 16384 16384 10.00 33682.24 20.27 -1.00 0.592 -1.00
After:
87380 16384 16384 10.00 34204.08 20.54 -1.00 0.590 -1.00
So the net result of this patch is that we have a small gain in throughput
due to a reduction in overhead for putting together the frame.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For i40e driver, each vector has its own ITR register. However, there
are no concept of queue-specific settings in the driver proper. Only
global variable is used to store ITR values. That will cause problems
especially when resetting the vector. The specific ITR values could be
lost.
This patch move rx_itr_setting and tx_itr_setting to i40e_ring to store
specific ITR register for each queue.
i40e_get_coalesce and i40e_set_coalesce are also modified accordingly to
support queue-specific settings. To make it compatible with old ethtool,
if user doesn't specify the queue number, i40e_get_coalesce will return
queue 0's value. While i40e_set_coalesce will apply value to all queues.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On all of the other Intel drivers we place checksum close to TSO as they
have a significant amount in common and it can help to reduce the decision
tree for how to handle the frame as the first check in TSO is to see if
checksumming is offloaded, and if it is not we can skip _BOTH_ TSO and Tx
checksum offload based on a single check.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to rewrite the logic for how we determine if we can
transmit the frame or if it needs to be linearized.
The previous code for this function was using a mix of division and modulus
division as a part of computing if we need to take the slow path. Instead
I have replaced this by simply working with a sliding window which will
tell us if the frame would be capable of causing a single packet to span
several descriptors.
The logic for the scan is fairly simple. If any given group of 6 fragments
is less than gso_size - 1 then it is possible for us to have one byte
coming out of the first fragment, 6 fragments, and one or more bytes coming
out of the last fragment. This gives us a total of 8 fragments
which exceeds what we can allow so we send such frames to be linearized.
Arguably the use of modulus might be more exact as the approach I propose
may generate some false positives. However the likelihood of us taking much
of a hit for those false positives is fairly low, and I would rather not
add more overhead in the case where we are receiving a frame composed of 4K
pages.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In an upcoming patch I would like to have access to the descriptor count
used for the data portion of the frame. For this reason I am splitting up
the descriptor count function from the function that stops the ring.
Also in order to try and reduce unnecessary duplication of code I am moving
the slow-path portions of the code out of being inline calls so that we can
just jump to them and process them instead of having to build them into
each function that calls them.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the code for determining the L4 protocol and L3 header
length so that when IPv6 extension headers are being used we can determine
the offset and type of the L4 protocol.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains a number of fixes to make certain that we are using
the correct protocols when parsing both the inner and outer headers of a
frame that is mixed between IPv4 and IPv6 for inner and outer.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL722 has support for providing the outer UDP tunnel checksum on
transmits. Make use of this feature to support segmenting UDP tunnels with
outer checksums enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is mostly a minor clean-up for the Rx checksum path in order to avoid
some of the unnecessary conditional checks that were being applied.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add exception handling to the Tx checksum path so that we can handle cases
of TSO where the frame is bad, or Tx checksum where we didn't recognize a
protocol
Drop I40E_TX_FLAGS_CSUM as it is unused, move the CHECKSUM_PARTIAL check
into the function itself so that we can decrease indent.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
