Reduce code size in the message transfer function by factoring out
a single-message transfer function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of I2C timeout, reset the HW only after the HW status
is read, otherwise the staus will be lost.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The delay in the driver seems to be not needed, so remove it.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Markus Grape <markus.grape@stericsson.com>
Tested-by: Per Persson <per.xb.persson@stericsson.com>
Tested-by: Chethan Krishna N <chethan.krishna@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
1) Increase RX FIFO threshold so that there is a reduction in
the number of interrupts handled to complete a transaction.
2) Fill TX FIFO in the write function.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It is seen that i2c-nomadik controller randomly stops generating the
interrupts leading to a i2c timeout. As a workaround to this problem,
add retries to the on going transfer on failure.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use the pm_runtime API for pins control.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[deleted some surplus runtime PM code]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Modify the code to:
1)Print the cause of i2c failure only if the status is set to ABORT.
2)Print slave address on send/receive fail, will help in which slave
failed.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Correct the incorrect initialization of adapter timeout not to be
in milliseconds, as it needs to be done in jiffies.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The abort cause string itself is an error, so remove the redundant
explicit error message.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The code was returning bad error numbers or just -1 in some cases.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This on-chip I2C controller needs to fetch the regulator
representing its voltage domain so that it won't be switched off.
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* Fix white space.
* Rename labels to something meaningful.
* Prefix defines with PORT_ to avoid collision with macros from
<linux/parport.h>.
* Add const markers where possible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Don't let other driver config options influence us, as it makes the
code more complex and fragile for a small benefit. There's nothing
wrong with instantiating I2C devices even if they don't have a driver.
And we're talking about 835 extra bytes in the binary on x86-64,
that's hardly worth arguing about.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Woodhouse <david.woodhouse@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Scanning the BIOS memory for the apanel information is costly, so
avoid doing it on non-Fujitsu machines.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I don't know if Fujitsu is ever going to produce Patsburg-based
machines, but if they do, I'd rather not probe the secondary (IDF)
SMBus channels. At least not until we have a good reason for doing so.
On a side note, I'm not even sure if it is right to enable detection
of HWMON and DDC devices on the IDF channels. Time will tell...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the SMBus controller DeviceID for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Ignore R_SH_NONE module relocations.
SH: SE7751: Fix pcibios_map_platform_irq prototype.
sh: remove warning and warning_symbol from struct stacktrace_ops
sh: wire up sys_sendmmsg.
clocksource: sh_tmu: Runtime PM support
clocksource: sh_tmu: __clocksource_updatefreq_hz() update
clocksource: sh_cmt: Runtime PM support
clocksource: sh_cmt: __clocksource_updatefreq_hz() update
dmaengine: shdma: synchronize RCU before freeing, simplify spinlock
dmaengine: shdma: add runtime- and system-level power management
dmaengine: shdma: fix locking
sh: sh-sci: sh7377 and sh73a0 build fixes
sh: cosmetic improvement: use an existing pointer
serial: sh-sci: suspend/resume wakeup support V2
serial: sh-sci: Runtime PM support
sh: select IRQ_FORCED_THREADING.
sh: intc: Set virtual IRQs as nothread.
sh: fixup fpu.o compile order
i2c: add a module alias to the sh-mobile driver
ALSA: add a module alias to the FSI driver
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be44
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
alg_data is already a pointer which must be passed directly.
Reported-by: Dieter Ripp <ripp@systecnet.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ben Dooks <ben-i2c@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support to the i2c-sh_mobile driver for setting
the I2C bus speed using platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the clock string magic from the i2c-sh_mobile driver
now when all platforms support clkdev properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This enables debouncing of the I2C lines. The debounce period is
2 * the debounce register field value, in terms of the I2C block's main
clock. The Tegra TRM indicates that a setting yielding >50nS is
desirable. Hence, a setting of 2 => 4 clocks @ 72MHz => ~55nS.
Signed-off-by: Ken Radtke <kradtke@nvidia.com>
[swarren: Added commit description body,
Fixed 80-column limit, Reverted file permission change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A repeated start should be used for all but the last msg in an xfer. The
NOSTART flag is for skipping the START frame (addr/rw)
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Re-init the I2C controller when an IRQ arrives with no
I2C_INT_STATUS bits set to indicate why the interrupt was sent.
Storms of such mystery interrupts are infrequently seen.
Dump some more status when these interrupts arrive. Set an error
for the current request and wake up the requester (rather than
timing out the request or possibly silently ignoring the interrupts).
If the I2C block is inside the DVC, also ACK the DVC I2C transfer
done interrupt in the ISR error return path, as is done for the
normal return path.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
[swarren: Fix minor checkpatch whitespace issue, commit tag]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For Tegra i2c controller to function properly new slave mode must be
enabled.
swarren notes:
In particular, I found this was needed when working on enabling the
Tegra audio driver on the Seaboard board. There are two different PCB
layouts for this board; a "clamshell" version, which works just fine
without this change, and the original non-clamshell version, which needs
this change in order for I2C to operate correctly. Without it, I2C
probing fails for some devices, e.g. with:
wm8903 0-001a: Device with ID register 0 is not a WM8903
wm8903 0-001a: asoc: failed to probe CODEC wm8903.0-001a: -19
asoc: failed to instantiate card tegra-wm8903: -19
ALSA device list:
No soundcards found.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use a standard list with proper locking to handle the list of
adapters. Thankfully it only matters on systems with more than one
parallel port, which are very rare.
Thanks to Lukasz Kapiec for reporting the problem to me.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Move the SMBus device ID definitions of recent devices from pci_ids.h
to the i2c-i801.c driver file. They don't have to be shared, as they
are clearly identified and only used in this driver. In the future,
such IDs will go to i2c-i801 directly. This will make adding support
for new devices much faster and easier, as it will avoid cross-
subsystem patch sets and merge conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Seth Heasley <seth.heasley@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch enables I2C driver autoloading on sh-mobile systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Apparently some distros set i2c-algo-bit.bit_test to 1 by
default. In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added. In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails. This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36221
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [.38 down to .34]
When warning on the use of deprecated i2c_driver methods
attach_adapter and detach_adapter, mention the name of the driver
which needs to be updated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
i2c-pxa2xx: Don't clear isr bits too early
i2c-pxa2xx: Fix register offsets
i2c-pxa2xx: pass of_node from platform driver to adapter and publish
i2c-pxa2xx: check timeout correctly
i2c-pxa2xx: add support for shared IRQ handler
i2c-pxa2xx: Add PCI support for PXA I2C controller
ARM: pxa2xx: reorganize I2C files
i2c-pxa2xx: use dynamic register layout
i2c-mxs: set controller to pio queue mode after reset
i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
isr is passed later into i2c_pxa_irq_txempty and
i2c_pxa_irq_rxfull and they may use some other bits
than irq sources.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix regression that was introduced by dynamic register layout.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
the of_node will auto-publish devices which are added to the device
tree.
Commit 925bb9c6 aka ("of/i2c: Fix module load order issue caused by
of_i2c.c) moved the of_i2c_register_devices() function from the i2c core
back to the drivers. This patch does the same thing for the pxa driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
timeout here maybe 0 if the event occured and a task with a higher
priority stole the cpu and we were sleeping longer than the timeout
value we specified.
In case of a real timeout I changed the error code to I2C_RETRY so we
retry the transfer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Sodaville has three of them on a single IRQ. IRQF_DISABLED is removed
because it is a NOP allready and scheduled for removal.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Sodaville I2C controller is almost the same as found on PXA2xx. The
difference:
- the register are at a different offset
- no slave support
The PCI probe code adds three platform devices which are probed then by
the platform code.
The X86 part also adds dummy clock defines because we don't have HW
clock support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.
This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
pxa910_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This will prepare the driver to handle register layouts where certain
registers are not available at all.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
mxs_reset_block() clears the PIO_QUEUE_MODE bit. So we have
to set it again after a controller reset.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the SMBus Controller DeviceIDs for the Intel DH89xxCC PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The last legitimate user of i2c_driver.attach_adapter and
.detach_adapter is gone, so we can finally deprecate these callbacks.
The last few drivers which still use these will have to be updated to
make use of standard I2C device instantiation ways instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the standard driver core mechanism to keep track of i2c adapters
present on the system: i2c_for_each_dev and a notifier. This will let
us deprecate and ultimately remove the legacy attach_adapter and
detach_adapter callbacks in i2c_driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Introduce i2c_for_each_dev(), an i2c device iterator with proper
locking for use by i2c-dev. This is needed so that we can get rid of
the attach_adapter and detach_adapter legacy callback functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename the parameter of i2c_get_adapter() to "nr", to make it clear we
are passing an adapter number and not an adapter ID (which have gone
away by now.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus/2639/i2c-1' of git://git.fluff.org/bjdooks/linux:
i2c-mpc: Add support for 64bit system
i2c: add driver for Freescale i.MX28
i2c: tegra: Add i2c support
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32: (40 commits)
unicore32: rewrite arch-specific tlb.h to use asm-generic version
unicore32: modify io_p2v and io_v2p macros, and adjust PKUNITY_mmio_BASEs
unicore32: replace unicore32-specific iomap functions with generic lib implementation
unicore32 machine related: add frame buffer driver for pkunity-v3 soc
unicore32 machine related files: add i2c bus drivers for pkunity-v3 soc
unicore32 io: redefine __REG(x) and re-use readl/writel funcs
unicore32 i8042 upgrade and bugfix: adjust resource request region type
unicore32 upgrade to v2.6.38-rc5: add one more paramter for pte_alloc_map call
unicore32 i8042: adjust io funcs of i8042-unicore32io.h
unicore32: rename PKUNITY_IOSPACE_BASE to PKUNITY_MMIO_BASE
unicore32: modify function names and parameters for irq_chips
unicore32: remove unused lines in arch/unicore32/include/asm/irq.h
unicore32 time.c: change calculate method for clock_event_device
unicore32: ADD MAINTAINER for unicore32 architecture
unicore32 machine related files: ps2 driver
unicore32 machine related files: pci bus handling
unicore32 machine related files: hardware registers
unicore32 machine related files: core files
unicore32 additional architecture files: boot process
unicore32 additional architecture files: low-level lib: misc
...
Acked-by: Arnd Bergmann <arnd@arndb.de>
change from original version -- by advice of Jean Delvare
1. remove global variable i2c_reg, replaced by local variables
2. replace ENXIO with ENODEV when no platform resources
3. add adapter->nr assignment before i2c_add_numbered_adapter() call
4. add judgement for i2c_del_adapter() return value
5. release adapter when driver removed
6. add __devexit for puv3_i2c_remove() function
7. modify several names to more appropriated ones
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
Currently i2c-mpc supports 32bit system only, this modification makes it
supported on both 32-bit and 64-bit systems. The P5020 is the first
64-bit PPC system with the i2c-mpc controller.
Based in patch from Xulei <B33228@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
ocores_i2c_of_probe needs to use a const __be32 type for handing
device tree property values. This patch fixed the following build
warning:
CC drivers/i2c/busses/i2c-ocores.o
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:254: warning: assignment discards qualifiers from pointer target type
drivers/i2c/busses/i2c-ocores.c:261: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.
This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support new device OKI SEMICONDUCTOR ML7213 IOH.
The ML7213 which is for IVI(In-Vehicle Infotainment) is a companion
chip for the Atom E6xx series and compatible with the Intel EG20T
PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently only supporting the PIOQUEUE-mode, because DMA-support for
this platform is not yet in mainline. When it becomes available and
support has been added to this driver, it will also be suitable for
i.MX23 and STMP3xxx.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Adds I2C bus driver for nVidia Tegra SoCs. Tegra includes 4 I2C
controllers, one of which is inside the Dynamic Voltage Controller
and has a slightly different register map.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.
On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.
The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: Richard woodruff <r-woodruff2@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer. However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:
1) runtime PM is disabled, either at compile time or dynamically
via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
leaving the i2c driver active (NOTE: runtime suspend transitions are
disabled during system suspend, so i2c activity during system
suspend will runtime resume the device, but not runtime (re)suspend it.)
Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.
NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use strlcpy instead of strncpy.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for the Diolan U2C-12 USB-I2C adapter.
It also updates MAINTAINERS to list the author as maintainer.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the PM core wishes to transition away from the legacy suspend
and resume methods and since removing them makes using PM core features
like runtime PM much easier start warning when a driver is registered
using the legacy methods.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When devices use dev_pm_ops the I2C API is implementing standard functionality
for integration with runtime PM and for checking for the presence of a per
device op. The PM core provides pm_generic_ functions implementing this
behaviour - use them to reduce coupling with future PM updates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove real devices first and dummy devices last. This gives device
driver which instantiated dummy devices themselves a chance to clean
them up before we do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: stable@kernel.org
The SCx200 ACB driver supports ISA hardware as well as PCI. The PCI
hardware is CS5535/CS5536 based, and the device that it grabs is handled by
the cs5535-mfd driver. This converts the SCx200 driver to use a
platform_driver rather than the previous PCI hackery.
The driver used to manually track the iface list (via linked list); now it
only does this for ISA devices. PCI ifaces are handled through standard
driver model lists.
It's unclear what happens in case of errors in the old ISA code; rather than
pretending the code actually cares, I've dropped the (implicit) ignorance
of return values and marked it with a comment.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/i2c-2638' of git://git.fluff.org/bjdooks/linux:
i2c-bfin-twi: move setup to the earlier subsys initcall
i2c-bfin-twi: handle faulty slave devices better
i2c-mv64xxx: send repeated START between messages in xfer
i2c-nomadik: fix regression on adapter name
i2c-omap: Set latency requirements only once for several messages
i2c-eg20t: add driver for Intel EG20T
i2c-ocores: add some device tree documentation
i2c-ocores: Use devres for resource allocation
i2c-ocores: Adapt for device tree
i2c-iop3xx: add iomem annotation
Some systems using this bus sometimes have very basic devices such as
regulators on the bus, so the I2C bus master needs to be loaded early.
This also matches the behavior of many other I2C bus master drivers.
Therefore initialize via subsys_initcall().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Faulty slave devices might drive SDA low after a transfer finishes. So,
when this scenario is detected, have the master generate up to 9 extra
clocks until the SDA is properly released.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The I2C specification explicitly describes both SDA and SCL as
bidirectional lines. An I2C master with a read-only SCL is thus not
compliant. If a slow slave stretches the clock, errors will happen,
so the bus can't be considered as reliable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use a function pointer to decide whether to call i2c_add_adapter or
i2c_add_numbered_adapter. This makes the code more compact than the
current strategy of having the common code in a separate function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.
E.G. something like:
---------- ---------- Bus segment 1 - - - - -
| | SCL/SDA | |-------------- | |
| |------------| |
| | | | Bus segment 2 | |
| Linux | GPIO 1..N | MUX |--------------- Devices
| |------------| | | |
| | | | Bus segment M
| | | |---------------| |
---------- ---------- - - - - -
SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 5a0e3ad6af added direct inclusion
of <linux/slab.h> to those source files that appeared to need it, but
somehow missed this. On most architectures <linux/slab.h> is still
indirectly included, but there are exceptions such as alpha.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As stated into file include/linux/i2c.h we must send a repeated START
between messages in the same xfer groupset:
* Except when I2C "protocol mangling" is used, all I2C adapters implement
* the standard rules for I2C transactions. Each transaction begins with a
* START. That is followed by the slave address, and a bit encoding read
* versus write. Then follow all the data bytes, possibly including a byte
* with SMBus PEC. The transfer terminates with a NAK, or when all those
* bytes have been transferred and ACKed. If this is the last message in a
* group, it is followed by a STOP. Otherwise it is followed by the next
* @i2c_msg transaction segment, beginning with a (repeated) START.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Mauro Barella <mbarella@vds-it.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Nomadik I2C adapter does not provide a name for the struct
passed into i2c_add_numbered_adapter() causing a regression on
2.6.37-rc3 due to commit 2236baa75f
adding sanity checks for adapters. Fix this by providing a name
proper.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ordinary I2C read consist of two messages. First a write operation
to tell register address and then read operation to get data.
CPU wake up latency is set and removed twice in read case.
Set latency requirement before the message processing loop
and remove the requirement after the loop to remove latency
adjustment operations between the messages.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This puts some documentation for the device tree configuration at the head
of the driver file. Hopefully this can get moved to a common area for this
type of documentation at a later date; unfortunately, there isn't really
such a place in the kernel tree at this time.
Furthermore, the regstep and clock-frequency parameters are really bus
parameters and should probably be passed to the driver in a better way.
Consider that a TODO.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch converts the i2c-cores driver to use devres routines for
resource allocation.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adapts the i2c-ocores driver for being defined and configured via
a device tree description.
The device tree bits need to be protected by CONFIG_OF guards as this is
still an optional feature.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Eliminate unnecessary casts and the following sparse warnings:
drivers/i2c/busses/i2c-iop3xx.c:65:9: warning: incorrect type in argument 1 (different base types)
drivers/i2c/busses/i2c-iop3xx.c:65:9: expected void const volatile [noderef] <asn:2>*<noident>
drivers/i2c/busses/i2c-iop3xx.c:65:9: got unsigned int
[ the previous warning is repeated 18 times ]
drivers/i2c/busses/i2c-iop3xx.c:456:33: warning: cast removes address space of expression
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This gets caught by the new sanity check code. Instead of the slash use a
different symbol. This was originally found by Major Lee who proposed a
rather more complex patch which changed the name according to the chip
type.
On the basis that we are in a late -rc and making Linus grumpy isn't always
a good idea (however fun) this is a simple alternative.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure I2C adapters being registered have the required struct
fields set. If they don't, problems will happen later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
This patch converts the i2c driver to use PM runtime apis
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
These are the extra 'Integrated Device Function' SMBus controllers found
on the Patsburg chipset. Mention the absence of slave mode support.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's poor form to keep driver state in global variables rather than
per-instance. It never really mattered in practice when there was only
one controller on the chipset, but the latest chipsets do have more
than one controller, so now we care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-2637/i2c-all' of git://git.fluff.org/bjdooks/linux:
i2c-intel-mid: Driver depends on PCI
i2c-intel-mid: support for Moorestown and Medfield platform
i2c-nomadik: fixup bus delays
i2c-nomadik: support smbus emulation
i2c-nomadik: dynamic clocking
i2c-nomadik: documentation fixes
i2c-s3c2410: Enable i2c clock only when doing some transfert
i2c-intel-mid driver uses PCI data structs and interfaces,
so it should depend on PCI. Fixes these build errors:
drivers/i2c/busses/i2c-intel-mid.c:977: error: implicit declaration of function 'pci_request_region'
drivers/i2c/busses/i2c-intel-mid.c:1077: error: implicit declaration of function 'pci_release_region'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ba Zheng <zheng.ba@intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
(Updated to address Ben's comments. With regard to the message segment
restriction it's not something we hit on the actual platform so while
I will investigate that further I don't think its a blocker to submission.
At worst its a spot over-restrictive)
From: Wen Wang <wen.w.wang@intel.com>
Initial release of the driver. Updated and verified on hardware.
Cleaned up as follows
Alan Cox:
Squash down the switches into tables, and use the PCI ident field. We
could perhaps take this further and put the platform and port number into
this.
uint32t -> u32
bracketing of case statements
spacing and '!' usage
Check the speed (which is now 0/1/2) is valid and ignore otherwise.
Fix remaining problems/suggestions from Jean's review
Fix items from Ben's review
Arjan van de Ven:
Initial power management hooks
Yong Wang <youg.y.wang@intel.com>:
Shared IRQ support
Wen Wang <wen.w.wang@intel.com>:
D3 support
Fixes for OCT test runs
Interrupt optimisations
Hong Liu <hong.liu@intel.com>
The runtime PM code is working on the wrong device (i2c_adapter->dev).
The correct one should be pci_dev->dev. This breaks attached i2c
slave devices with runtime PM enabled. Slave device needs to runtime
resume parent device before runtime resuming itself, but we always get
error since we don't have pm_runtime callback for i2c_adapter->dev.
Bin Yang <bin.yang@intel.com>:
Update speed table
Saadi Maalem <saadi.maalem@intel.com>:
Clear all interrupts in the hardware init
Celine Chotard <celinex.chotard@intel.com>:
Correct ordering of clear/disable of IRQs
Signed-off-by: Wen Wang <wen.w.wang@intel.com>
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Bin Yang <bin.yang@intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
NULL-terminating pci_device_id in pch_dma.c and scx200_acb.c
for appying MODULE_DEVICE_TABLE (to publish modalias-es).
Signed-off-by: Dzianis Kahanovich <mahatma@eu.by>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
ctrl_* is deprecated. We should to use __raw_*.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We were missing a transfer delay in one execution path leading to
hangs and the bus timeout was too low leading to errors under
stress tests.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We can do smbus emulation so flag this and drop the duplicate
flags implied from smbus emulation.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This makes sure the Nomadik I2C bus driver silicon is only clocked
when really needed, saving some microamps here and there when
there is no I2C traffic.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This fixes some kerneldoc and assorted documenatation in the
Nomadik I2C driver without semantic impact.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Transactions not acked can happen every now and then, in particular
during device detection, and various transaction types can be used for
this purpose. So stop logging this event, except when debugging is
enabled. This is what other similar drivers (e.g. i2c-i801 or
i2c-piix4) do.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The underlying I2C adapter may or may not be present when this driver
gets initialized, and may disappear later, so there is no safe time at
which the probe and remove functions can be discarded.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for PCA9541, an I2C Bus Master Selector.
The driver is modeled as single channel I2C Multiplexer to be able to utilize
the I2C multiplexer framework.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Check the class flags before allocating the temporary i2c_client
structure, to avoid allocating it when we don't need it.
Also optimize the inner loop a bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
The "new_device" sysfs interface has been there for quite some time
now, nobody complained about it so it must be good enough. Time to
remove the warning and call it stable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michael Lawnick <ml.lawnick@gmx.de>
The functions the functions amd_ec_wait_write and amd_ec_wait_read have an
unsigned return type, but return a negative constant to indicate an error
condition.
A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
identifier f;
constant C;
@@
unsigned f(...)
{ <+...
* return -C;
...+> }
// </smpl>
Fixing amd_ec_wait_write and amd_ec_wait_read leads to the need to adjust
the return type of the functions amd_ec_write and amd_ec_read, which are
the only functions that call amd_ec_wait_write and amd_ec_wait_read.
amd_ec_write and amd_ec_read, in turn, are only called from within the
function amd8111_access, which already returns a signed typed value. Each
of the calls to amd_ec_write and amd_ec_read are updated using the
following semantic patch:
// <smpl>
@@
@@
+ status = amd_ec_write
- amd_ec_write
(...);
+ if (status) return status;
@@
@@
+ status = amd_ec_read
- amd_ec_read
(...);
+ if (status) return status;
// </smpl>
The patch also adds the declaration of the status variable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
These drivers don't use anything which is defined in <linux/i2c-id.h>.
This header file was never meant to be included directly anyway, and
will be deleted soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
i2c->adap.name shouldn't be used in request_irq.
Instead the driver name "i2c-pca-platform" should be used.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
drivers/i2c/algos/Kconfig makes all the algorithms dependent on
!I2C_HELPER_AUTO, which triggers a Kconfig warning about broken
dependencies when some driver selects one of the algorithms. Ideally
we would make only the prompts dependent on !I2C_HELPER_AUTO, however
Kconfig doesn't currently support that. So we have to redefine the
symbols separately for the I2C_HELPER_AUTO=y case.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Michal Marek <mmarek@suse.cz>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc/44x: Update ppc44x_defconfig
powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option
fsl_rio: Add comments for sRIO registers.
powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig
powerpc/fsl-booke: Add p5020 DS board support
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes
powerpc/fsl-booke: Add support for FSL 64-bit e5500 core
powerpc/85xx: add cache-sram support
powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board
powerpc: Fix compile error with paca code on ppc64e
powerpc/fsl-booke: Add p3041 DS board support
oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt.
powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips
powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers
powerpc/fsl_booke: Add support to boot from core other than 0
powerpc/p1022: Add probing for individual DMA channels
powerpc/fsl_soc: Search all global-utilities nodes for rstccr
powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT
powerpc/mpc83xx: Support for MPC8308 P1M board
...
Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
This patch modify the s3c2410 i2c driver behaviour to enable the
i2c clock only when needed. I'm not sure if this has a big impact
on power usage but at least it's fixing a bug with the uda1380
codec which needs to be hard reset'ed if the i2c clock is enabled
before it's powered on (at least on h1940).
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch updates the defines for Intel devices in
include/linux/pci_ids.h, referenced in arch/x86/pci/irq.c and
drivers/i2c/busses/i2c-i801.c, reflecting approved legal branding, and
using fuller code-names for products under development.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The i2c_imx_trx_complete() function is using
wait_event_interruptible_timeout() to wait for the I2C controller to
signal that it has completed an I2C bus operation. If the process that
causes the I2C operation receives a signal, the wait will be
interrupted, returning an error. It is better to let the I2C operation
finished before handling the signal (i.e. returning into userspace).
It is safe to use wait_event_timeout() instead, because the timeout
will allow the process to exit if the I2C bus hangs. It's also better
to allow the I2C operation to finish, because unacknowledged I2C
operations can cause the I2C bus to hang.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is an improvement to 4bba0fd8d1
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
