Supposedly on some platforms we can get extra atomicity guarantees for
CURPOS if we write it between the CURCNTR and CURBASE. Let's move the
CURPOS handling into the platform specific hooks to make the possible
without having to pass the calculated CURPOS around. And while at it,
do the same for the CURBASE to avoid passing that either.
v2: Use I915_WRITE_FW() and grab uncore.lock
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> #v1
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-7-ville.syrjala@linux.intel.com
Move the CURPOS calculations to seprate function. This will allow
sharing the code between the 845/865 vs. others codepaths when we
otherwise split them apart.
v2: Don't pass intel_plane as it's not needed
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-6-ville.syrjala@linux.intel.com
Move cursor_base, cursor_cntl, and cursor_size from intel_crtc
into intel_plane so that we don't need the crtc for cursor stuff
so much.
Also entirely nuke cursor_addr which IMO doesn't provide any benefit
since it's not actually used by the cursor code itself. I'm not 100%
sure what the SKL+ DDB is code is after by looking at cursor_addr so
I just make it do its checks unconditionally. If that's not correct
then we should likely replace it with somehting like
plane_state->visible.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The remaining cursor base address calculations are spread
around into several different locations. Just pull it all
into one place.
v2: Don't pass intel_plane as we don't really need it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170327185546.2977-4-ville.syrjala@linux.intel.com
Now that the watermarks are in order, it should be safe to enable sprite
planes on g4x. We alreday have the code in fact, we just call it ilk_.
Let's rename to g4x_ and let it loose.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-16-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Implement proper two stage watermark programming for g4x. As with
other pre-SKL platforms, the watermark registers aren't double
buffered on g4x. Hence we must sequence the watermark update
carefully around plane updates.
The code is quite heavily modelled on the VLV/CHV code, with some
fairly significant differences due to the different hardware
architecture:
* g4x doesn't use inverted watermark values
* CxSR actually affects the watermarks since it controls memory self
refresh in addition to the max FIFO mode
* A further HPLL SR mode is possible with higher memory wakeup
latency
* g4x has FBC2 and so it also has FBC watermarks
* max FIFO mode for primary plane only (cursor is allowed, sprite is not)
* g4x has no manual FIFO repartitioning
* some TLB miss related workarounds are needed for the watermarks
Actually the hardware is quite similar to ILK+ in many ways. The
most visible differences are in the actual watermakr register
layout. ILK revamped that part quite heavily whereas g4x is still
using the layout inherited from earlier platforms.
Note that we didn't previously enable the HPLL SR on g4x. So in order
to not introduce too many functional changes in this patch I've not
actually enabled it here either, even though the code is now fully
ready for it. We'll enable it separately later on.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170421181432.15216-13-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The current code looks like a typo, the specification calls for setting
bits 31:24 to 0x8C, while preserving bits 23:0. Fix things accordingly.
I'm not aware of the typo causing a real problem, so the fix is only for
consistency.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494408113-379-1-git-send-email-imre.deak@intel.com
If "crtc" is NULL, then my static checker complains that "ret" isn't
initialized on that path. It doesn't really cause a problem unless
"ret" is somehow set to -EDEADLK which is not likely.
Chris Wilson also noticed another error path where "ret" isn't set
correctly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170414195425.GA8144@mwanda
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This reverts commit ea49c9acf2.
mode_config.mutex was originally added to fix WARNs in connector
functions, but now that atomic nonblocking modeset support is
included, we will likely never hold any any lock at all.
The WARN mentioned in commit bbf35e9def ("drm/i915:
Pass atomic state to intel_audio_codec_enable, v2."), so it's
safe to revert this now.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491312168-18147-1-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten needs both the new connector->atomic_check hook and the
connection_mutex locking changes in the probe helpers to be able to
start merging the connector property conversion to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Last drm-misc-next pull req for 4.12
Core changes:
- fb_helper checkpatch cleanup and simplified _add_one_connector() (Thierry)
- drm_ioctl and drm_sysfs improved/gained documentation (Daniel)
- [ABI] Repurpose reserved field in drm_event_vblank for crtc_id (Ander)
- Plumb acquire ctx through legacy paths to avoid lock_all and legacy_backoff
(Daniel)
- Add connector_atomic_check to check conn constraints on modeset (Maarten)
- Add drm_of_find_panel_or_bridge to remove boilerplate in drivers (Rob)
Driver changes:
- meson moved to drm-misc (Neil)
- Added support for Amlogic GX SoCs in dw-hdmi (Neil)
- Rockchip unbind actually cleans up the things bind initializes (Jeffy)
- A couple misc fixes in virtio, dw-hdmi
NOTE: this also includes a backmerge of drm-next as well rc5 (we needed vmwgfx
as well as the new synopsys media formats)
* tag 'drm-misc-next-2017-04-07' of git://anongit.freedesktop.org/git/drm-misc: (77 commits)
Revert "drm: Don't allow interruptions when opening debugfs/crc"
drm: Only take cursor locks when the cursor plane exists
drm/vmwgfx: Fix fbdev emulation using legacy functions
drm/rockchip: Shutdown all crtcs when unbinding drm
drm/rockchip: Reorder drm bind/unbind sequence
drm/rockchip: analogix_dp: Disable clock when unbinding
drm/rockchip: vop: Unprepare clocks when unbinding
drm/rockchip: vop: Enable pm domain before vop_initial
drm/rockchip: cdn-dp: Don't unregister audio dev when unbinding
drm/rockchip: cdn-dp: Don't try to release firmware when not loaded
drm: bridge: analogix: Destroy connector & encoder when unbinding
drm: bridge: analogix: Disable clock when unbinding
drm: bridge: analogix: Unregister dp aux when unbinding
drm: bridge: analogix: Detach panel when unbinding analogix dp
drm: Don't allow interruptions when opening debugfs/crc
drm/virtio: don't leak bo on drm_gem_object_init failure
drm: bridge: dw-hdmi: fix input format/encoding from plat_data
drm: omap: use common OF graph helpers
drm: convert drivers to use drm_of_find_panel_or_bridge
drm: convert drivers to use of_graph_get_remote_node
...
Last 4.12 feature pile:
GVT updates:
- Add mdev attribute group for per-vgpu info
- Time slice based vGPU scheduling QoS support (Gao Ping)
- Initial KBL support for E3 server (Han Xu)
- other misc.
i915:
- lots and lots of small fixes and improvements all over
- refactor fw_domain code (Chris Wilson)
- improve guc code (Oscar Mateo)
- refactor cursor/sprite code, precompute more for less overhead in
the critical path (Ville)
- refactor guc/huc fw loading code a bit (Michal Wajdeczko)
* tag 'drm-intel-testing-2017-04-03' of git://anongit.freedesktop.org/git/drm-intel: (121 commits)
drm/i915: Update DRIVER_DATE to 20170403
drm/i915: Clear gt.active_requests before checking idle status
drm/i915/uc: Drop use of MISSING_CASE on trivial enums
drm/i915: make a few DDI functions static
drm/i915: Combine reset_all_global_seqno() loops into one
drm/i915: Remove redudant wait for each engine to idle from seqno wrap
drm/i915: Wait for all engines to be idle as part of i915_gem_wait_for_idle()
drm/i915: Move retire-requests into i915_gem_wait_for_idle()
drm/i915/uc: Move fw path check to fetch_uc_fw()
drm/i915/huc: Remove unused intel_huc_fini()
drm/i915/uc: Add intel_uc_fw_fini()
drm/i915/uc: Add intel_uc_fw_type_repr()
drm/i915/uc: Move intel_uc_fw_status_repr() to intel_uc.h
drivers: gpu: drm: i915L intel_lpe_audio: Fix kerneldoc comments
drm/i915: Suppress busy status for engines if wedged
drm/i915: Do request retirement before marking engines as wedged
drm/i915: Drop verbose and archaic "ring" from our internal engine names
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/guc: Take enable_guc_loading check out of GEM core code
...
By using the same structure for both interruptible and
uninterruptible locking in shrinker code, combined with the
information that mm.interruptible is only being written to, the
code can be greatly simplified.
Also removing the i915_gem_ prefix from the locking functions so
that nobody in their wildest dreams considers exporting them.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1491562175-27680-1-git-send-email-joonas.lahtinen@linux.intel.com
mode_valid() called from drm_helper_probe_single_connector_modes()
may need to look at connector->state because what a valid mode is may
depend on connector properties being set. For example some HDMI modes
might be rejected when a connector property forces the connector
into DVI mode.
Some implementations of detect() already lock all state,
so we have to pass an acquire_ctx to them to prevent a deadlock.
This means changing the function signature of detect() slightly,
and passing the acquire_ctx for locking multiple crtc's.
For the callbacks, it will always be non-zero. To allow callers
not to worry about this, drm_helper_probe_detect_ctx is added
which might handle -EDEADLK for you.
Changes since v1:
- Always set ctx parameter.
Changes since v2:
- Always take connection_mutex when probing.
Changes since v3:
- Remove the ctx from intel_dp_long_pulse, and add
WARN_ON(!connection_mutex) (danvet)
- Update docs to clarify the locking situation. (danvet)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1491504920-4017-1-git-send-email-maarten.lankhorst@linux.intel.com
It just doesn't work. It probably stopped working way, way before that
(e.g. i915 grabbed random mutexes all over in modeset code at least
since gen6), but with atomic and all the ww_mutex stuff it's indeed
hopeless.
Remove ->mode_set_base_atomic from the 2 atomic drivers (i915 and
nouveau) that still had one (both had dummy implementations already
anyway), and shunt atomic drivers in the helpers debug_enter/leave
functions.
I'll leave the code in for radeon and amdgpu, but I think as soon as
amdgpu is atomic we should think about just ripping it out. Only
having it around for radeon and pre-nv50 is rather pointless. This
would also allow us to nuke all that code from fbdev.
Funny part is that _all_ kms drivers set this hook, despite that no
one else provides the required ->mode_set_base_atomic implementation.
The reason I'm jumping on this is that I want to wire up a full
acquire ctx for the benefit of atomic drivers, everywhere. And the
debug_enter/leave implementations call ->gamma_set. And there's just
no way ever we can create an acquire_ctx in the nmi context of kgdb.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-11-daniel.vetter@ffwll.ch
We do set DRIVER_ATOMIC now.
Note that the comment is outdated, the property paths switched over to
checking drm_drv_uses_atomic_modeset() a while ago. Which means this
can't even break if we revert DRIVER_ATOMIC again.
v2: Add note that this is even safer (Maarten).
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-9-daniel.vetter@ffwll.ch
With all the callers of drm_modeset_lock_crtc gone, and all the places
it was formerly used properly wiring the acquire ctx through, we can
remove this.
The only hidden context magic we still have is now the global one.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170403083304.9083-4-daniel.vetter@ffwll.ch
We're clearing the legacy_cursor_update flag before calling
drm_atomic_helper_setup_commit() which means the helper will
wait for the flip to complete before cleaning up the framebuffers.
That's not what we want for the legacy cursor, so let's clear
the flag after setting up the commit.
Also toss in a FIXME about solving these problems in a nicer
way using the fabled vblank workers.
v2: Also unsync with legacy page flips
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Rafael Ristovski <rafael.ristovski@gmail.com>
Fixes: a5509abda4 ("drm/i915: Fix legacy cursor vs. watermarks for ILK-BDW")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170329142123.5923-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
v2 of the commit 2c77bb29d3 ("drm: simplify the locking in the GETCRTC ioctl")
accidentally introduced a unrelated change in intel_display.c, revert the
unrelated change.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 2c77bb29d3 ("drm: simplify the locking in the GETCRTC ioctl")
Reported-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/6be47261-475f-c190-af56-c136677246d9@linux.intel.com
No need to grab both plane and crtc locks at the same time, we can do
them one after the other. If userspace races it'll get what it
deserves either way.
This removes another user of drm_modeset_lock_crtc. There's only one
left.
v2: Make sure all access to primary->state is properly protected
(Harry).
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170328070145.21520-1-daniel.vetter@ffwll.ch
Just rolling it out, no code change here.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170322215058.8671-3-daniel.vetter@ffwll.ch
Several major vendor USB-C->HDMI converters, in particular the DA200,
fail to recover a 5.4 GHz 1 lane signal if the link N is greater than
0x80000.
The link M and N depend on the pixel clock and link clock ratio. With
current code link N exceeds 0x80000 only when link clock >= 540000
kHz. Except for the eDP intermediate link clocks, at least the four
least significant bits are always zero. Just one bit shift right would
be enough to bring even the DP 1.4 810000 kHz link clock under 0x80000
link N. The pixel clock for modes that require a link clock >= 540000
kHz would also have several least significant bits zero. Unless the user
provides a mode with an odd pixel clock value, we can reduce the numbers
to reach the goal, with no loss in precision.
The DP spec even mentions sources making choices that "allow for static
and relatively small Mvid and Nvid values", thus reducing the link M/N
regardless of the sink in question seems justified.
Everything here is based on the work and information gathered by Clint
Taylor <clinton.a.taylor@intel.com>. This is just an iteration to reduce
the parameters regardless of lane count, link rate, or sink.
Reference: http://patchwork.freedesktop.org/patch/msgid/1490225256-11667-1-git-send-email-clinton.a.taylor@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93578
Tested-by: Mads <mads@ab3.no>
Tested-by: PJ <foobar@pjmodos.net>
Tested-by: François Guerraz <kubrick@fgv6.net>
Tested-by: Lev Popov <leo@nabam.net>
Tested-by: Igor Krivenko <igor.s.krivenko@gmail.com>
Tested-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490614405-23337-1-git-send-email-jani.nikula@intel.com
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
All it does is pick the encoder and call intel_get_shared_dpll(). We
can just do this in the caller. One less indirection level during code
reading.
As another plus, now the two callers of intel_get_shared_dpll() are
{ironlake,haswell}_crtc_compute_clock().
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1490209125-20046-2-git-send-email-paulo.r.zanoni@intel.com
All the pre-SKL sprite planes compute the x/y/tile offsets in a
similar way. There are a couple of minor differences but the primary
planes have those as well. Thus i9xx_check_plane_surface()
already does what we need, so let's use it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-7-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The effective difference between i9xx_update_primary_plane()
and ironlake_update_primary_plane() is only the HSW/BDW
DSPOFFSET special case. So bring that over into
i9xx_update_primary_plane() and eliminate the duplicated code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-6-ville.syrjala@linux.intel.com
Extract the primary plane surfae offset/x/y calculations for
pre-SKL platforms into a common function, and call it during the
atomic check phase to reduce the amount of stuff we have to do
during the commit phase. SKL is already doing this.
v2: Update the comment about the rotation adjustments to
match the code better (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-5-ville.syrjala@linux.intel.com
Computing the plane control register value is branchy so moving it out
from the plane commit hook seems prudent. Let's pre-compute it during
the atomic check phase and store the result in the plane state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-4-ville.syrjala@linux.intel.com
Share the code to compute the primary plane control register value
between the i9xx and ilk codepaths as the differences are minimal.
Actually there are no differences between g4x and ilk, so the
current split doesn't really make any sense.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Pull the code to calculate the pre-SKL primary plane control register
value into separate functions. Allows us to pre-compute it in the
future.
v2: Split the pre-ilk vs. ilk+ unification to a separate patch (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170323192712.30682-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
On SKL the planes are uniform so the "sprites" can use the
primary plane code perfectly fine. The only difference we
have is the color key handling, but since we never enable that
for the primary plane the same code works just fine.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170317211808.14693-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
The only time we need to emit a flush inside request emission is after
an execbuffer, for which we can use the full __i915_add_request(). All
other instances want the simpler i915_add_request() without flushing, so
remove the useless helper.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170317114709.8388-1-chris@chris-wilson.co.uk
I915_RESET_IN_PROGRESS is being used for both signaling the requirement
to i915_mutex_lock_interruptible() to avoid taking the struct_mutex and
to instruct a waiter (already holding the struct_mutex) to perform the
reset. To allow for a little more coordination, split these two meaning
into a couple of distinct flags. I915_RESET_BACKOFF tells
i915_mutex_lock_interruptible() not to acquire the mutex and
I915_RESET_HANDOFF tells the waiter to call i915_reset().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170316171305.12972-1-chris@chris-wilson.co.uk
Optimize the plane register accesses a little bit by grabbing
the uncore lock manually across the entire pile of accesses and
using I915_READ_FW().
This helps keep the pipe update vblank evade critical section
below our 100 usec deadline, particularly with lockdep enabled.
And in general we want to keep that critical section as short
as possible as it's executed with interrupts disabled.
Not all plane updates currently happen from within the vblank evade
critical section, so we must use the irqsave/irqrestore variants
of the spinlock functions in the plane hooks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-5-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Pull all the plane register writes closer together to avoid having
a lot of unrelated stuff in between them. This will make things more
clear once we'll grab the uncore lock around the entire bunch. Also
in the future we might even consider moving more of the register
value computation out from the plane update hooks. This should make
that easier to do.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170309154434.29303-4-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Add a big fat warning in __intel_display_resume that the old state is
invalid, and use the correct state everywhere.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489071125-917-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[mlankhorst: Change one occurence of conn_state to new_conn_state in
verify_connector_state, and drop old_conn_state there]
The trouble here is that looking at all connector->state in the
verifier isn't good, because that's run from the commit work, which
doesn't hold the connection_mutex. Which means we're only allowed to
look at states in our atomic update.
The simple fix for future proofing would be to switch over to
drm_for_each_connector_in_state, but that has the problem that the
verification then fails if not all connectors are in the state. And we
also need to be careful to check both old and new encoders, and not
screw things up when an encoder gets reassigned.
Note that this isn't the full fix, since we still look at
connector->state. To fix that, we need Maarten's patch series to
switch over to state pointers within drm_atomic_state, but that's a
different series.
v2: Use oldnew iterator (Maarten).
v3: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-6-daniel.vetter@ffwll.ch
This gets rid of the last users of for_each_intel_connector(), remove
that too.
At first I wasn't sure whether the 2 loops in the modeset state
checker should instead only loop over the connectors in the atomic
commit. But we never add connectors to an atomic update if they don't
(or won't have) a CRTC assigned, which means there'd be a gap in check
coverage. Hence loop over everything on those too.
v2: Rebase onto the iter_get/put->iter_begin/end rename.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-5-daniel.vetter@ffwll.ch
Drive-by fixup while looking at all the connector_list walkers -
holding connection_mutex does actually _not_ give you locking to look
at the legacy drm_connector->encoder->crtc pointer chain. That one is
solely owned by the atomic commit workers. Instead we must inspect the
atomic state.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301095226.30584-4-daniel.vetter@ffwll.ch
DRM_UT_CORE generates way too much noise usually, so having the
framebuffer init failures use DRM_UT_CORE is a pain when trying to
find out the reason why you failed in creating a framebuffer.
Let's use DRM_UT_KMS for these debug messages instead.
v2: s/at less than/at most/ in the debug message (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-6-ville.syrjala@linux.intel.com
Let's try to keep the alignment requirements in one place, and so
towards that end let's move the AUX_DIST alignment handling into
intel_surf_alignment() alongside the main surface alignment stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307194210.13400-3-ville.syrjala@linux.intel.com
