GDB uses a PTRACE_PEEKUSR call with offset 0 to see
if a thread is alive, so provide a success return for
this particular special case.
Signed-off-by: David S. Miller <davem@davemloft.net>
This effectively undoes the PCI resource allocation changes done in
commit b408cbc704, but leaves the cleanups
of that commit in place.
We're going back to marking the resources reported by e820 busy _before_
doing PCI probing, so that any PCI resource that clashes with the BIOS-
reported memory map will be reloacted to a non-clashing area.
The reason? Larry Finger reports that his laptop has the cardbus
controller set up by the BIOS so that it conflicts with the e820 memory
map, and needs to be relocated. See
http://bugzilla.kernel.org/show_bug.cgi?id=6337
for more details.
We'll have to work out how to handle the fbcon problem that caused that
commit in the first place in some other way.
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: <bjk@luxsci.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Or rather compute it based on the table length automatically.
This also has the intended side effect of not warning for new system calls
anymore.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix CONFIG_REORDER.
The value of cflags-y was assined to CFLAGS before cflags-y was assigned
the value used for CONFIG_REORDER.
Use cflags-y for all CFLAGS options in the Makefile to avoid this
happening again.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In linux-2.6.16, we have noticed a problem where the gs base value
returned from an arch_prtcl(ARCH_GET_GS, ...) call will be incorrect if:
- the current/calling task has NOT set its own gs base yet to a
non-zero value,
- some other task that ran on the same processor previously set their
own gs base to a non-zero value.
In this situation, the ARCH_GET_GS code will read and return the
MSR_KERNEL_GS_BASE msr register.
However, since the __switch_to() code does NOT load/zero the
MSR_KERNEL_GS_BASE register when the task that is switched IN has a zero
next->gs value, the caller of arch_prctl(ARCH_GET_GS, ...) will get back
the value of some previous tasks's gs base value instead of 0.
Change the arch_prctl() ARCH_GET_GS code to only read and return
the MSR_KERNEL_GS_BASE msr register if the 'gs' register of the calling
task is non-zero.
Side note: Since in addition to using arch_prctl(ARCH_SET_GS, ...),
a task can also setup a gs base value by using modify_ldt() and write
an index value into 'gs' from user space, the patch below reads
'gs' instead of using thread.gs, since in the modify_ldt() case,
the thread.gs value will be 0, and incorrect value would be returned
(the task->thread.gs value).
When the user has not set its own gs base value and the 'gs'
register is zero, then the MSR_KERNEL_GS_BASE register will not be
read and a value of zero will be returned by reading and returning
'task->thread.gs'.
The first patch shown below is an attempt at implementing this
approach.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the HPET timer is enabled, the clock can drift by ~3 seconds a day.
This is due to the HPET timer not being initialized with the correct
setting (still using PIT count).
If HZ changes, this drift can become even more pronounced.
HPET patch initializes tick_nsec with correct tick_nsec settings for
HPET timer.
Vojtech comments:
"It's not entirely correct (it assumes the HPET ticks totally
exactly), but it's significantly better than assuming the PIT error
there."
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mostly to get better handling when a extended config space
access has to fallback to Type1.
Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Previously only the first bus would be checked against Type 1.
Why 16? Checking all would need too much memory and we
can assume that systems with more than 16 busses have better than
average quality BIOS.
This is an additional defense against bad MCFG tables.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Intel EM64T CPUs handle uncanonical return addresses differently
from AMD CPUs.
The exception is reported in the SYSRET, not the next instruction.
This leads to the kernel exception handler running on the user stack
with the wrong GS because the kernel didn't expect exceptions
on this instruction.
This version of the patch has the teething problems that plagued an earlier
version fixed.
This is CVE-2006-0744
Thanks to Ernie Petrides and Asit B. Mallick for analysis and initial
patches.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Machine checks can stall the machine for a long time and
it's not good to trigger the nmi watchdog during that.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This prevents crashes on dual core system when enough ticks are lost.
Replaces earlier patch by me.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMD systems have a modern APIC that supports 8 bit IDs, but
don't have a XAPIC version number. Add a new "modern_apic"
subfunction that handles this correctly and use it (nearly)
everywhere where XAPIC is tested for.
I removed one wart: the code specified that external APICs
would use an 8bit APIC ID. But I checked a real 82093 data sheet
and it says clearly that they only use 4bit. So I removed
this special case since it would a bit awkward to implement now.
I removed the valid APIC tests in mptable parsing completely. On any modern
system they only check against the full field width (8bit) anyways
and are no-ops. This also fixes them doing the wrong thing
on >8 core Opterons.
This makes i386 boot again on 16 core Opterons.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Needed for other checks later in ACPI.
Pointed out by Len Brown
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When nolapic was passed or the local APIC was disabled
for another reason ACPI would still parse the IO-APICs
until these were explicitely disabled with noapic.
Usually this resulted in a non booting configuration unless
"nolapic noapic" was used.
I also disabled the local APIC parsing in this case, although
that's only cosmetic (suppresses a few printks)
This hopefully makes nolapic work in all cases.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Horus systems don't have anything on bus 0 which makes
the Type 1 sanity checks fail. Use the DMI BIOS year to
check for newer systems and always assume Type 1 works on them.
I used 2001 as an pretty arbitary cutoff year.
Cc: gregkh@suse.de
Cc: Navin Boppuri <navin.boppuri@newisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a user for the e820_all_mapped function:
There have been several machines that don't have a working MMCONFIG,
often because of a buggy MCFG table in the ACPI bios. This patch adds a
simple sanity check that detects a whole bunch of these cases, and when
it detects it, linux now boots rather than crash-and-burns.
The accuracy of this detection can in principle be improved if there was
a "is this entire range in e820 with THIS attribute", but no such
function exist and the complexity needed for this is not really worth
it; this simple check already catches most cases anyway.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a e820_all_mapped() function which checks if the entire range
<start,end> is mapped with type.
This is done by moving the local start variable to the end of each
known-good region; if at the end of the function the start address is
still before end, there must be a part that's not of the correct type;
otherwise it's a good region.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename e820_mapped to e820_any_mapped since it tests if any part of the
range is mapped according to the type.
Later steps will introduce e820_all_mapped which will check if the
entire range is mapped with the type. Both have their merit.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The node setup code would try to allocate the node metadata in the node
itself, but that fails if there is no memory in there.
This can happen with memory hotplug when the hotplug area defines an so
far empty node.
Now use bootmem to try to allocate the mem_map in other nodes.
And if it fails don't panic, but just ignore the node.
To make this work I added a new __alloc_bootmem_nopanic function that
does what its name implies.
TBD should try to use nearby nodes here. Currently we just use any.
It's hard to do it better because bootmem doesn't have proper fallback
lists yet.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Keith Mannthey, Andi Kleen
Implement memory hotadd without sparsemem. The memory in the SRAT
hotadd area is just preserved instead and can be activated later.
There are a few restrictions:
- Only one continuous hotadd area allowed per node
The main problem is dealing with the many buggy SRAT tables
that are out there. The strategy here is to reject anything
suspicious.
Originally from Keith Mannthey, with several hacks and changes by AK
and also contributions from Andrew Morton
[ TBD: Problems pointed out by KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>:
1) Goto's rebuild_zonelist patch will not work if CONFIG_MEMORY_HOTPLUG=n.
Rebuilding zonelist is necessary when the system has just memory <
4G at boot, and hot add memory > 4G. because x86_64 has DMA32,
ZONE_NORAML is not included into zonelist at boot time if system
doesn't have memory >4G at boot.
[AK: should just force the higher zones at boot time when SRAT tells us]
2) zone and node's spanned_pages and present_pages are not incremented.
They should be.
For example, our server (ia64/Fujitsu PrimeQuest) can equip memory
from 4G to 1T(maybe 2T in future), and SRAT will *always* say we have
possible 1T +memory. (Microsoft requires "write all possible memory
in SRAT") When we reserve memmap for possible 1T memory, Linux will
not work well in +minimum 4G configuraion ;)
[AK: needs limiting to 5-10% of max memory]
]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Memory hotadd doesn't need SPARSEMEM, but can be handled by just preallocating
mem_maps. This only needs some untangling of ifdefs to enable the necessary
code even without SPARSEMEM.
Originally from Keith Mannthey, hacked by AK.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just call IRET always, no need for any special cases.
Needed for the next bug fix.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Wire up sys_sync_file_range() into syscall tables.
[SPARC]: Wire up sys_splice() into the syscall tables.
[SPARC64]: Update defconfig.
[SPARC64]: Align address in huge_pte_alloc().
[SPARC64]: Document the instruction checks we do in do_sparc64_fault().
[SPARC64]: Make tsb_sync() mm comparison more precise.
Patch from Pavel Pisa
This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.
There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.
Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(We'd only added the number, which meant that actually trying
to use splice just went off into la-la-land)
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update misc OMAP core code from linux-omap tree:
- McBSP updates by Samuel Ortiz, Andrzej Zaborowski
- Whitespace cleanups by Ladislav Michl
- Other fixes by various linux-omap developers
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP framebuffer low-level init code from linux-omap tree
by Imre Deak.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP PM code from linux-omap tree:
- Move PM code from plat-omap to mach-omap1 and mach-omap2
by Tony Lindgren
- Add minimal PM support for omap24xx by Tony Lindgren and
Richard Woodruff
- Misc updates to omap1 PM code by Tuukka Tikkanen et al
- Updates to the SRAM code needed for PM and FB by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP GPIO code from linux-omap tree:
- Fix omap16xx edge control by Juha Yrjola
- Support for additional omap16xx trigger modes by Dirk Behme
- Fix edge detection by Tony Lindgren et al.
- Better support for omap15xx and omap310 by Andrej Zaborowski
- Fix omap15xx interrupt bug by Petukhov Nikolay
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP pin multiplexing code from linux-omap tree.
This patch adds new pin configurations by various OMAP
developers, and suport for omap730 by Brian Swetland.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP timers from linux-omap tree. The highlights of the
patch are:
- Move timer32k code from mach-omap1 to plat-omap and make it
work also on omap24xx by Tony Lindgren
- Add support for dmtimer idle check for PM by Tuukka Tikkanen
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP clock framework from linux-omap tree.
The highlights of the patch are:
- Add support for omap730 clocks by Andrzej Zaborowski
- Fix compile warnings by Dirk Behme
- Add support for using dev id by Tony Lindgren and Komal Shah
- Move memory timings and PRCM into separate files by Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the platform device resources for the Ethernet and
MMC peripherals. It also adds platform device information for the NAND
(SmartMedia), I2C and the RTC.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
