Kalle Valo says:
====================
wireless-next patches for v5.18
Third set of patches for v5.18. Smaller set this time, support for
mt7921u and some work on MBSSID support. Also a workaround for rfkill
userspace event.
Major changes:
mac80211
* MBSSID beacon handling in AP mode
rfkill
* make new event layout opt-in to workaround buggy user space
rtlwifi
* support On Networks N150 device id
mt76
* mt7915: MBSSID and 6 GHz band support
* new driver mt7921u
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These function is used to stop transmitting when we are going to switch
channels or do some RF calibration. Before these operations, we need to
stop channel transmission and backup setting into parameter tx_en. After
operations are done, resume transmitting by backup parameter tx_en.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-13-pkshih@realtek.com
The format of RF parameter is changed; it doesn't encode delay parameters
into table, but the delay coding becomes regular pair of register address
and value.
To help firmware to recover RF register settings, we need to download
these parameters to firmware. For v1 format, only download partial
parameters (ignore them with addr < 0x100).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-6-pkshih@realtek.com
Building iwlmei without CONFIG_CFG80211 causes a link-time warning:
ld.lld: error: undefined symbol: ieee80211_hdrlen
>>> referenced by net.c
>>> net/wireless/intel/iwlwifi/mei/net.o:(iwl_mei_tx_copy_to_csme) in archive drivers/built-in.a
Add an explicit dependency to avoid this. In theory it should not
be needed here, but it also seems pointless to allow IWLMEI
for configurations without CFG80211.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Emmanuel Grumbach <Emmanuel.grumbach@intel.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220316183617.1470631-1-arnd@kernel.org
When setup monitor mode in DFS channel, mt76 send CH_SWITCH_DFS to
fw for channel config. This would cause rx performance bad while
monitoring frames. Settings CH_SWITCH_NORMAL in monitor mode would
get the same performance as normal channels.
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
IEEE80211_CONF_CHANGE_MONITOR would be set every time even when vif runs as
sta mode.
If vif runs as sta mode, the beacon filter would be falsely enabled
earlier than the associated state.
That is not the behavior the firmware expects and also breaks the original
logic of sta mode. Thus, we only limit the operation to set the beacon
filter only for monitor mode when IEEE80211_CONF_CHANGE_MONITOR is set.
Fixes: 4ad65a5461 ("mt76: mt7921: toggle runtime-pm adding a monitor vif")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Due to the missing IEEE80211_RADIOTAP_HE_DATA1_BW_RU_ALLOC_KNOWN in
status report, the HE rate in wirehsark/tcpdump always shows wrong value.
Applications will refer to IEEE80211_RADIOTAP_HE_DATA5_DATA_BW_RU_ALLOC
when the flag is set and shows the correct data rate.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Firmware initialization can take a while. Move mt7921_init_hw routine in
a dedicated work in order to not slow down bootstrap process.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce __mt76u_init unitility routine and move mt7615 usb bus ops
into mt7615 module in order to allow specifying driver specific
parameter.
This is a preliminary patch to add usb support to mt7921 driver.
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Various spelling mistakes in comments.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some of beamforming mib counters are moved to different offsets
or registers in newer chipsets.
Fixes: 99ad32a4ca ("mt76: mt7915: add support for MT7986")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop invalid rssi value to calculate a reasonable report
Fixes: 4550fb9e98 ("mt76: improve signal strength reporting")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Switch to use le32/16_get_bits() to simplfy codes and specify
the size explicitly to avoid potential issues.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't populate the read-only array ba_range on the stack but
instead make it static const. Also makes the object code a little
smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If devm_pinctrl_get() fails then it leads to an error pointer
dereference. Add a check to prevent that.
Fixes: 99ad32a4ca ("mt76: mt7915: add support for MT7986")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A-die 7976 has different offset and uses different channel group
definition on txpower init values.
Fixes: 99ad32a4ca ("mt76: mt7915: add support for MT7986")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since there are no HT & VHT IEs being sent in 6ghz,
some capabilities judgement and parsing for wtbl &
starec configuration should be modified to reflect such changes.
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Money Wang <Money.Wang@mediatek.com>
Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This improves rate reach performance on units with polarized antennas.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt7921s driver may receive frames with fragment buffers. If there is a
CTS packet received in monitor mode, the payload is 10 bytes only and
need 6 bytes header padding after RXD buffer. However, only RXD in the
first linear buffer, if we pull buffer size RXD-size+6 bytes with
skb_pull(), that would trigger "BUG_ON(skb->len < skb->data_len)" in
__skb_pull().
To avoid the nonlinear buffer issue, enlarge the RXD size from 128 to
256 to make sure all MCU operation in linear buffer.
[ 52.007562] kernel BUG at include/linux/skbuff.h:2313!
[ 52.007578] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 52.007987] pc : skb_pull+0x48/0x4c
[ 52.008015] lr : mt7921_queue_rx_skb+0x494/0x890 [mt7921_common]
[ 52.008361] Call trace:
[ 52.008377] skb_pull+0x48/0x4c
[ 52.008400] mt76s_net_worker+0x134/0x1b0 [mt76_sdio 35339a92c6eb7d4bbcc806a1d22f56365565135c]
[ 52.008431] __mt76_worker_fn+0xe8/0x170 [mt76 ef716597d11a77150bc07e3fdd68eeb0f9b56917]
[ 52.008449] kthread+0x148/0x3ac
[ 52.008466] ret_from_fork+0x10/0x30
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix mt7921_queues_acq implementation according to the vendor sdk.
Fixes: 474a9f21e2 ("mt76: mt7921: add debugfs support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
