A very small number of devices don't use the flow control offered by
requestor lines. In these specific cases, the pxa dma driver should be
aware of that and not try to use a requestor line.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The valid pchan range is 0 ~ d->dma_requests - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When putting back a descriptor to the free descs list, some fields are
not set to 0, it can cause bugs if someone uses it without having this
in mind.
Descriptor are not put back one by one so it is easier to clean
descriptors when we request them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The addressing mode we were using was not only incrementing the address at
each microblock, but also at each data boundary, which was severely slowing
the transfer, without any benefit since we were not using the data stride.
Switch to the micro block increment only in order to get back to an
acceptable performance level.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 6007ccb577 ("dmaengine: xdmac: Add interleaved transfer support")
Cc: stable@vger.kernel.org #4.2
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dmitry Vyukov reported the following using trinity and the memory
error detector AddressSanitizer
(https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerForKernel).
[ 124.575597] ERROR: AddressSanitizer: heap-buffer-overflow on
address ffff88002e280000
[ 124.576801] ffff88002e280000 is located 131938492886538 bytes to
the left of 28857600-byte region [ffffffff81282e0a, ffffffff82e0830a)
[ 124.578633] Accessed by thread T10915:
[ 124.579295] inlined in describe_heap_address
./arch/x86/mm/asan/report.c:164
[ 124.579295] #0 ffffffff810dd277 in asan_report_error
./arch/x86/mm/asan/report.c:278
[ 124.580137] #1 ffffffff810dc6a0 in asan_check_region
./arch/x86/mm/asan/asan.c:37
[ 124.581050] #2 ffffffff810dd423 in __tsan_read8 ??:0
[ 124.581893] #3 ffffffff8107c093 in get_wchan
./arch/x86/kernel/process_64.c:444
The address checks in the 64bit implementation of get_wchan() are
wrong in several ways:
- The lower bound of the stack is not the start of the stack
page. It's the start of the stack page plus sizeof (struct
thread_info)
- The upper bound must be:
top_of_stack - TOP_OF_KERNEL_STACK_PADDING - 2 * sizeof(unsigned long).
The 2 * sizeof(unsigned long) is required because the stack pointer
points at the frame pointer. The layout on the stack is: ... IP FP
... IP FP. So we need to make sure that both IP and FP are in the
bounds.
Fix the bound checks and get rid of the mix of numeric constants, u64
and unsigned long. Making all unsigned long allows us to use the same
function for 32bit as well.
Use READ_ONCE() when accessing the stack. This does not prevent a
concurrent wakeup of the task and the stack changing, but at least it
avoids TOCTOU.
Also check task state at the end of the loop. Again that does not
prevent concurrent changes, but it avoids walking for nothing.
Add proper comments while at it.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Based-on-patch-from: Wolfram Gloger <wmglo@dent.med.uni-muenchen.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@alien8.de>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: kasan-dev <kasan-dev@googlegroups.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Wolfram Gloger <wmglo@dent.med.uni-muenchen.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20150930083302.694788319@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
pm_runtime_enable is called in probe to enable runtime PM
for wm8962 codec, but pm_runtime_disable isn't called in remove
callback, nor is called in error path if probe fails after runtime
PM is enabled, this causes unbalanced pm_runtime_enable.
This patch Adds pm_runtime_disable in remove callback and error path,
to balance pm_runtime_enable.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull RCU fixes from Ingo Molnar:
"Two RCU fixes:
- work around bug with recent GCC versions.
- fix false positive lockdep splat"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Suppress lockdep false positive for rcp->exp_funnel_mutex
rcu: Change _wait_rcu_gp() to work around GCC bug 67055
As reported by Dmitry Vyukov, we really shouldn't do ipc_addid() before
having initialized the IPC object state. Yes, we initialize the IPC
object in a locked state, but with all the lockless RCU lookup work,
that IPC object lock no longer means that the state cannot be seen.
We already did this for the IPC semaphore code (see commit e8577d1f03:
"ipc/sem.c: fully initialize sem_array before making it visible") but we
clearly forgot about msg and shm.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was added for completeness, but we don't have any users
for it yet. Daniel noted that it may be racy. Remove it.
Change-Id: I5f5546f8911a4f294008a62dc86a73f3face38d1
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The CONFIG_MIPS_MT symbol can be selected by CONFIG_MIPS_VPE_LOADER in
addition to CONFIG_MIPS_MT_SMP. We only want MT code in the CPS SMP boot
vector if we're using MT for SMP. Thus switch the config symbol we ifdef
against to CONFIG_MIPS_MT_SMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10867/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MT-specific code in mips_cps_boot_vpes can safely be omitted from
kernels which don't support MT, with the default VPE==0 case being used
as it would be after the has_mt (Config3.MT) check failed at runtime.
Discarding the code entirely will save us a few bytes & allow cleaner
handling of MT ASE instructions by later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The has_mt macro ended with a branch, leaving its callers with a delay
slot that would be executed if Config3.MT is not set. However it would
not be executed if Config3 (or earlier Config registers) don't exist
which makes it somewhat inconsistent at best. Fill the delay slot in the
macro & fix the mips_cps_boot_vpes caller appropriately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.16+
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32
zone, as is the case for some 32-bit kernels, then massage_gfp_flags()
will cause DMA memory allocated for devices with a 32..63-bit
coherent_dma_mask to fall back to using __GFP_DMA, even though there may
only be 32-bits of physical address available anyway.
Correct that case to compare against a mask the size of phys_addr_t
instead of always using a 64-bit mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: a2e715a86c ("MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.")
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 2.6.36+
Patchwork: https://patchwork.linux-mips.org/patch/9610/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Digi 002/003 family uses asynchronous transaction for messaging.
The address to transmit this message is stored on a certain register.
This commit allocates a range of address on OHCI 1394 host controller
to handle the messaging. As long as I know, the purpose of this message
seems to notify lost of synchronization. While, the meaning of content
of the message is not clear.
Actual examples of this messaging:
* When clock source is set as internal:
- 0x00007051
- 0x00007052
- 0x00007054
- 0x00007057
- 0x00007058
* When clock source is set as somewhat external:
- 0x00009000
- 0x00009010
- 0x00009020
- 0x00009021
- 0x00009022
The lost often occurs when using internal clock source. In this case,
users hear sounds with quite short gap every several minutes. In fact,
the lost is recovered temporarily.
When using with external clock source, the lost seems not to occur. The
mechanism is not clear yet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds PCM functionality to transmit/receive PCM samples.
Any PCM substreams are jointed because incoming/outgoing AMDTP streams
are bound. When one of PCM substream is running or external clock source
is selected, current sampling rate is used. Else, the sampling rate is
changed as an userspace application requests.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds proc node to show current clock status for debugging.
As long as testing Digi 002 rack, registers can show local clock rate,
local clock source. When external clock input such as S/PDIF is
connected, the registers show the detection and external clock rate.
Additionally, the registers show the mode of optical digital input
interface. Although, a tester with Digi 003 rack reports this makes no
sense. Further investigation is required for Digi 003 series.
Besides, in Digi 002 rack, the S/PDIF format must be IEC 60958-4,
so-called professional.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to manage streaming.
The streaming is not controlled by CMP in IEC 61883-6. It's controlled by
IEEE 1394 write transaction to certain addresses.
Several clock sources are available, while there're no differences about
packet transmission. The value of SYT field in transmitted packets is
always zero. Thus, streams in both direction don't build synchronization.
And the device always requires received packets to transmit packets. This
driver keeps to transfer outgoing stream even if they're not required.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Digi 002/003 family uses its own format for data blocks. The format is
quite similar to AM824 in IEC 61883-6, while there're some differences:
* The Valid Bit Length (VBL) code is always 0x40 in Multi-bit Linear Audio
(MBLA) data channel.
* The first data channel includes MIDI messages, against IEC 61883-6
recommendation.
* The Counter field is always zero in MIDI conformant data channel.
* Sequence multiplexing in IEC 61883-6 is not applied to the MIDI
conformant data channel.
* PCM samples are scrambled in received AMDTP packets. We call the way
as Double-Oh-Three (DOT). The algorithm was discovered by
Robin Gareus and Damien Zammit in 2012.
This commit adds data processing layer to satisfy these differences.
There's a quirk about transmission mode for received packets. When this
driver applies non-blocking mode to outgoing packets with isochronous
channel 2 or more, after 15 to 20 seconds since playbacking, any PCM
samples causes noisy sound on the device. With isochronous channel 0 or 1,
this doesn't occur. As long as I investigated, this quirk is not observed
when applying blocking mode to the received packets.
This driver applies blocking mode to outgoing packets, while non-blocking
mode to incoming packgets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for Digidesign 002/003 family. This commit
just creates/removes card instance according to bus event. More functions
will be added in following commits.
Digidesign 002/003 family consists of:
* Agere FW802B for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* ALTERA ACEX EP1K50 for IEC 61883 layer and DSP controller
* ADSP-21065L for signal processing
[minor cleanup using skip_spaces() by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
drm_kms_helper_poll_enable() is called from a context in
intel_hpd_irq_storm_disable() where the the mode_config mutex is
already locked.
When this function was converted to lock this mutex in
commit 8c4ccc4ab6 ("drm/probe-helper: Grab mode_config.mutex
in poll_init/enable") a deadlock occurred.
Call the newly implemented non-locking version of this function.
Changes since v1:
- use function name suffix '_locked' for the function that
is to be called from a locked context.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm_kms_helper_poll_enable() was converted to lock the mode_config
mutex in commit 8c4ccc4ab6
("drm/probe-helper: Grab mode_config.mutex in poll_init/enable").
This disregarded the cases where this function is called from a context
where this mutex is already locked.
Add a non-locking version as well.
Changes since v1:
- use function name suffix '_locked' for the function that
is to be called from a locked context.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21
to do tune, assume there were 10 clock phase need to try, phase 0 to
phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so
the last CMD19/CMD21 will get CRC error, host->need_retune was set and
cause mmc_retune was called, then dead loop of mmc_retune
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03 ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When we're out of command buffer space, we turn on the command buffer
processed irq without re-checking for finished command buffers afterwards.
This might lead to a missed irq and the command submission process waiting
forever for space.
Fix this by rerunning the command buffer submission handler whenever we're
out of command space. This ensures both that we don't needlessly turn on
the irq, and that if we decide to turn on the irq, we recheck for finished
command buffers before going to sleep.
Reported-and-tested-by: Bryan Li <ldexin@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The lack of const leads to a compile warning after merging i915
upstream tree:
drivers/gpu/drm/i915/intel_audio.c:147:13: note: expected 'struct drm_display_mode *' but argument is of type 'const struct drm_display_mode *'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case we have less than maximum allowed channels (8) and autoconfiguration is
enabled the DWC_PARAMS read is wrong because it uses different arithmetic to
what is needed for channel priority setup.
Re-do the caclulations properly. This now works on AVR32 board well.
Fixes: fed2574b3c (dw_dmac: introduce software emulation of LLP transfers)
Cc: yitian.bu@tangramtek.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The only thing mode_fixup was doing was set the adjusted_mode->vrefresh to
60, but it already has the value of 60 when the decon_mode_fixup() is
called. That means this call is actually pointless and can be removed.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The only thing mode_fixup was doing was set the adjusted_mode->vrefresh to
60, but it already has the value of 60 when the fimd_mode_fixup() is
called. That means this call is actually pointless and can be removed.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch fixes an over flow issue with the TX ring descriptor. Each
descriptor is 32B in size and an operation requires 2 of these
descriptors.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_release_channel() decrements privatecnt counter and almost all dma_get*
function increments it with the exception of dma_get_slave_channel().
In most cases this does not cause issue since normally the channel is not
requested and released, but if a driver requests DMA channel via
dma_get_slave_channel() and releases the channel the privatecnt will be
unbalanced and this will prevent for example getting channel for memcpy.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Protect the rotator_clk_crtl() function with an #ifdef CONFIG_PM guard
to avoid "defined but not used" warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Protect the fimc_clk_ctrl() function with an #ifdef CONFIG_PM guard to
avoid "defined but not used" warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Protect the suspend and resume callbacks with an #ifdef CONFIG_PM_SLEEP
guard to avoid "defined but not used" warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Don't create a fake mmap offset in exynos_drm_gem_dumb_map_offset. If
not, it will call drm_gem_create_mmap_offset whenever user requests
DRM_IOCTL_MODE_MAP_DUMB ioctl.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The drm_gem_object_release() function already performs this cleanup,
so there is no reason to do it explicitly.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All the user of these functions are inside exynos-drm driver and
you don't need to export the symbols for that case.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The beginning of statement in function is next line of a brace.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
By if statment, some function callings are written twice. It needs
several line feed by indentation in if statment. Make to one function
calling from outside if statment.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The exynos_drm_gem_init() is used only in exynos_drm_gem.c file. Make it
static and don't export it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
They will be freed right or was freed already, so NULL assignment is
unnecessary.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When obj->import_attach is existed, code calling drm_prime_gem_destroy()
was removed from commit 67e93c808b ("drm/exynos: stop copying sg
table"), and it's a fault.
The drm_prime_gem_destroy() is cleanup function which GEM drivers need
to call when they use drm_gem_prime_import() to import dma-bufs, so
exynos-drm driver using drm_gem_prime_import() needs calling
drm_prime_gem_destroy().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no guarantee that DMA addresses are the same as physical
addresses, but dma_to_pfn() knows how to convert a dma_addr_t to a PFN
which can then be converted to a struct page.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
