Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate the arrays on the stack, instead make them static.
Makes the object code smaller by over 950 bytes:
Before:
text data bss dec hex filename
26144 18768 352 45264 b0d0 drivers/hwmon/asc7621.o
After:
text data bss dec hex filename
25029 18928 352 44309 ad15 drivers/hwmon/asc7621.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TI LM5066I hotswap controller is a more accurate version of the
LM5066 device already supported. It has different measurement conversion
coefficients than the LM5066, so it needs to be recognized as a
different device.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When converting the DIRECT format CURRENT_IN and POWER commands, make
the offset coefficient ("b") predicate on the value of the current limit
setting.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps:
- VR13.0 mode, 10-mV DAC - 0x24
- VR13.0 mode, 5-mV DAC - 0x27
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor IBM CFF power supplies with hwmon over
pmbus.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
[groeck: drop 'default n'; include bitops.h instead of jiffies.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TSI channel has a 4 channel mux connected to it and is normally
used for touchscreen support. The hardware may alternatively
use it as general purpose adc.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If the touchscreen pins are used as general purpose analogue
input, the touchscreen driver should not be used. The pins
will be handled by the existing hwmon driver instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix checkpatch warnings about S_IRUGO being less readable than
providing the permissions octal as '0444'.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add register details an channels definition for using the TSI
registers in the hwmon driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With CONFIG_THERMAL=m, a built-in aspeed pwm tacho driver causes
a link error:
drivers/hwmon/aspeed-pwm-tacho.o: In function `aspeed_pwm_tacho_probe':
aspeed-pwm-tacho.c:(.text+0x7f0): undefined reference to `thermal_of_cooling_device_register'
This adds a dependency similar to what other hwmon drivers use,
ensuring that the aspeed driver cannot be built-in in this
case but has to be a module. With THERMAL=n, we still allow building it.
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Export all the available status registers through debugfs. This is
useful for hardware diagnostics, especially on multi-page pmbus devices,
as user-space access of the i2c space could corrupt the pmbus page
accounting.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support in aspeed-pwm-tacho driver for cooling device creation.
This cooling device could be bound to a thermal zone
for the thermal control. Device will appear in /sys/class/thermal
folder as cooling_deviceX. Then it could be bound to particular
thermal zones. Allow specification of the cooling levels
vector - PWM duty cycle values in a range from 0 to 255
which correspond to thermal cooling states.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It's add support for cooling device creation to
aspeed-pwm-tacho.
Cooling device could be bound to a thermal zone
for the thermal control.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add PB_STATUS_INPUT as the generic alarm bit for iin and pin. We also
need to redo the status register checking before setting up the boolean
attribute, since it won't necessarily check STATUS_WORD if the device
doesn't support it, which we need for this bit.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pmbus always reads byte data from the status register, even if
configured to use STATUS_WORD. Use a function pointer to read the
correct amount of data from the registers.
Also switch to try STATUS_WORD first before STATUS_BYTE on init.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the storage of status registers to 16 bit values. This allows us
to store all the bits of STATUS_WORD.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After a suspend / resume cycle we possibly need to reapply chip registers
settings that we had set or fixed in a probe path, since they might have
been reset to default values or set incorrectly by a BIOS again.
Tested on a Gigabyte M720-US3 board, which requires routing internal VCCH5V
to in7 (and had it wrong again on resume from S3).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
[groeck: Return value from it87_resume_sio() is unused; make it void]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit splits out chip registers setting code on probe path to
separate functions so they can be reused for setting the device properly
again when system resumes from suspend.
While we are at it let's also make clear that on IT8720 and IT8782 it's
the VCCH5V line that is (possibly) routed to in7.
This will make it consistent with a similar message that it printed on
IT8783.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3562 320 8 3890 f32 drivers/hwmon/i5k_amb.o
File size After adding 'const':
text data bss dec hex filename
3658 224 8 3890 f32 drivers/hwmon/i5k_amb.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10055 7032 0 17087 42bf drivers/hwmon/adt7475.o
File size After adding 'const':
text data bss dec hex filename
10567 6520 0 17087 42bf drivers/hwmon/adt7475.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2304 2936 0 5240 1478 drivers/hwmon/adc128d818.o
File size After adding 'const':
text data bss dec hex filename
2344 2872 0 5216 1460 drivers/hwmon/adc128d818.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6161 9400 0 15561 3cc9 drivers/hwmon/nct7802.o
File size After adding 'const':
text data bss dec hex filename
6465 9080 0 15545 3cb9 drivers/hwmon/nct7802.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6655 304 0 6959 1b2f drivers/hwmon/hwmon.o
File size After adding 'const':
text data bss dec hex filename
6703 240 0 6943 1b1f drivers/hwmon/hwmon.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If stts751 hw by some reason reports conversion rate bigger then 9:
ret = i2c_smbus_read_byte_data(priv->client, STTS751_REG_RATE);
then dereferencing stts751_intervals[priv->interval] leads to buffer
overrun.
The patch adds sanity check for value stored on chip.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 7f07ec0fa1 ("hwmon: new driver for ST stts751 thermal sensor")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
sysfs store functions should return the number of bytes written.
Returning zero results in an endless loop.
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Thilo Cestonaro <thilo.cestonaro@ts.fujitsu.com>
[groeck: Clean up documentation change and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix loop preventing some platforms from waking up via the power
button in s2idle.
intel-vbtn:
- match power button on press rather than release
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZhjtgAAoJEKbMaAwKp3647u4IALEnsRt10hj2ognbpQUPxqzB
uwjlQ7ukqwWVbpgElQ6q2hKUFHNnk2CGuzIEjvRKpme0UpsSPUQRPZGeUGDmvC3l
cOxNSmyTJkmeCEU9G7yj1NrcaOEFQ9iRLrZmSRnYBSWBgjzYdpfC/xog2y8mVkgO
FQAU2ul9Ph5eXEOTQBw56LtzsraJtBdV76aKESuJEAw3h0E8svhLeV43caVic/Go
Yv9aRZRkj/5oQHwXe+GC5K4dFdWFYZ9iGLQFHgcICRACcUq7p0ysVvf8YMVQplyR
Xm2j8Dq1ierId5g90p5fznIM4BeBnIM2Iclkk4dPaIrP3Fogd9eq1gvxQKvWgpY=
=IOnZ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fix from Darren Hart:
"Fix loop preventing some platforms from waking up via the power button
in s2idle:
- intel-vbtn: match power button on press rather than release"
* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: intel-vbtn: match power button on press rather than release
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlmHbBAACgkQ8vlZVpUN
gaMu3gf+LpI5bI1XA3R8KbXB2snnz6wM7OzArfqvreX+m+xP1CK6nVpAIgpkZqfw
QkQ1xPJk7Q25vex/pPcsgLO0Vxf0i4vpydK+fYnf30S4WvGQVq6OHZWFFv2zM2YB
7TWxjG+KryM7j6JSXdUiSTKP3nX84TW/IMIWuZMR1nuOa8N5M4yD3uc+3EBTjSbq
P/dxfmkp2hQKnlZVBWqCjJDhtxwUYTF4iZ/pbSVeGbgHCh1674ml+airb4K9ltNU
0vR0JChD12YJaafjaAyIrqqKwDGvnN+H5wyhCodEV9w8jthbcU04Jfmi1auB9UxT
y7/sgbV64W2o5hBwxY3RXjZkVLpDsw==
=Mtr7
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
Pull MIPS fixes from Ralf Baechle:
"This fixes two build issues for ralink platforms, both due to missing
#includes which used to be included indirectly via other headers"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: mt7620: Add missing header
MIPS: ralink: Fix build error due to missing header
The latest change of compat_sys_sigpending in commit 8f13621abc
("sigpending(): move compat to native") has broken it in two ways.
First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.
Second, on big endian architectures these bytes are being written in the
wrong order.
This bug was found by strace test suite.
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621abc ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug was found by a static code checker tool for copy paste
problems.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks. This may
caused the superblock being corrupted with zero blocks count.
Fixes: 1c6bd7173d
Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+
When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.
Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.
Besides that, we clean up unnecessary check and move some relative checks
into it.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>
ext4_xattr_inode_read() currently reads each block sequentially while
waiting for io operation to complete before moving on to the next
block. This prevents request merging in block layer.
Add a ext4_bread_batch() function that starts reads for all blocks
then optionally waits for them to complete. A similar logic is used
in ext4_find_entry(), so update that code to use the new function.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
When an xattr block has a single reference, block is updated inplace
and it is reinserted to the cache. Later, a cache lookup is performed
to see whether an existing block has the same contents. This cache
lookup will most of the time return the just inserted entry so
deduplication is not achieved.
Running the following test script will produce two xattr blocks which
can be observed in "File ACL: " line of debugfs output:
mke2fs -b 1024 -I 128 -F -O extent /dev/sdb 1G
mount /dev/sdb /mnt/sdb
touch /mnt/sdb/{x,y}
setfattr -n user.1 -v aaa /mnt/sdb/x
setfattr -n user.2 -v bbb /mnt/sdb/x
setfattr -n user.1 -v aaa /mnt/sdb/y
setfattr -n user.2 -v bbb /mnt/sdb/y
debugfs -R 'stat x' /dev/sdb | cat
debugfs -R 'stat y' /dev/sdb | cat
This patch defers the reinsertion to the cache so that we can locate
other blocks with the same contents.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
