This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for this new phy ID.
Signed-off-by: Rick Hoover <RHoover@digilentinc.com>
Signed-off-by: Steven Wang <steven.wang@digilentinc.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This phy is on Xilinx ZC702 zynq development board.
Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use macros from linux/marvell_phy.h instead of duplicate
magic phy ID in the driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove trailing white space
- Remove spaces before tag
- Fix comments
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_init_eee has to exit with an error when the
local device and its link partner both do not support EEE.
So this patch fixes a problem when verify this.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_spi_driver() removes some boilerplate and makes the code
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM63xx PHY driver is for the SoC internal PHYs, flag these
as internal PHY devices.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libphy currently always reports a PHY as an external transceiver from
the ethtool output. This is inaccurate, because some drivers should be
able to tell that a PHY device is an internal transceiver of an Ethernet
MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers
just like other flags, and a corresponding helper: phy_is_internal()
which can be used by networking drivers to query if a given
PHY device is internal.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently no way for an Ethernet MAC driver servicing PHY link
interrupts to notify this to the PHY state machine without defining its
own state machine. Since most drivers are not so special, introduce a
helper: phy_mac_interrupt() which can be called from a link up/down
interrupt routine to update the PHY state machine. To avoid code
duplication some refactoring has been done to expose the workqueue and
its corresponding callback internally.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY device is registered with the special IRQ value
PHY_IGNORE_INTERRUPT (-2) it will not properly be handled by the PHY
library:
- it continues to poll its register, while we do not want this
because such PHY link events or register changes are serviced by an
Ethernet MAC
- it will still try to configure PHY interrupts at the PHY level, such
interrupts do not exist at the PHY but at the MAC level
- the state machine only handles PHY_POLL, but should also handle
PHY_IGNORE_INTERRUPT similarly
This patch updates the PHY state machine and initialization paths to
account for the specific PHY_IGNORE_INTERRUPT. Based on an earlier patch
by Thomas Petazzoni, and reworked to add the missing bits. Add a helper
phy_interrupt_is_valid() which specifically tests for a PHY interrupt
not to be PHY_POLL or PHY_IGNORE_INTERRUPT and use it throughout the
code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phylib uses workqueues for multiple purposes. There is no real dependency of
scheduling these on the cpu which scheduled them.
On a idle system, it is observed that and idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.
This patch replaces system_wq with system_power_efficient_wq for PHYLIB.
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.
Also fix some comment formatting to make it consistent and to comply
with the netdev style.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of fixed speed set up for a NIC (e.g. ethtool -s eth0 autoneg off speed
100 duplex full) with an ethernet cable plugged off, the mentioned algorithm
slows down a NIC speed, so further cable hook-up leads to nonoperable link state.
Signed-off-by: Kirill Kapranov <kapranoff@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver macro removes some boilerplate and
simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_platform_driver macro removes some boilerplate and
simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag MICREL_PHY_50MHZ_CLK is not of exclusive use of KSZ8051
model. At least KSZ8021 and KSZ8031 models also use it.
This patch moves the handling of this and future flags to a
separate function so that the different PHY models can call it on
their init function, if needed.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special
initialization of "Operation Mode Strap Override" in reg 0x16
introduced in 212ea99 (phy/micrel: Implement support for KSZ8021).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function is only used in this file, should be static and not
an exported symbol.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phyter KSZ9021 has hardware bug. If asymmetric pause is enabled,
then it is necessary to disconnect and then reconnect the ethernet
cable to get the phyter working. The solution is to disable the
asymmetric pause.
Signed-off-by: Vlastimil Kosar <ikosar@fit.vutbr.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory leak in phy_device_free() for the case when phy_device*
returned by phy_device_create() is not registered in the system.
Bug description:
phy_device_create() sets name of kobject using dev_set_name(), which
allocates memory using kvasprintf(), but this memory isn't freed if
the underlying device isn't registered properly, because kobject_cleanup()
is not called in that case. This can happen (and actually is happening on
our machines) if phy_device_register(), called by mdiobus_scan(), fails.
Patch description:
Embedded struct device is initialized in phy_device_create() and it
counterpart phy_device_free() just drops one reference to the device,
which leads to proper deinitialization including releasing the kobject
name memory.
Signed-off-by: Petr Malat <oss@malat.biz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
This patch replaces the horribly coded of_count_named_gpios() with a
call to of_count_phandle_with_args() which is far more efficient. This
also changes the return value of of_gpio_count() & of_gpio_named_count()
from 'unsigned int' to 'int' so that it can return an error code. All
the users of that function are fixed up to correctly handle a negative
return value.
v2: Split GPIO portion into a separate patch
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc failures already get standardized OOM
messages and a dump_stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary of changes:
.Newly added phys
-KSZ8081/KSZ8091, which has some phy ids.
-KSZ8061
-KSZ9031, which is Gigabit phy.
-KSZ886X, which has a switch function.
-KSZ8031, which has a same phy ids with KSZ8021.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimal driver to manage the
Realtek RTL8211E 10/100/1000 Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code that always enables copper/fiber autoselect,
ignoring the DIS_FC strapping pin. The default value for this
register is autoselect on anyway, and if you explicitly disable
autoselect via strapping you probably really don't want
autoselect.
Signed-off-by: Stef van Os <stef.van.os@prodrive.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct a mistake made in the previous commit due to reckless
copy-and-pasting.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SMSC PHY in power down mode can't be used.
If a SMSC PHY is in this mode in the config_init
stage, the mode "all capable" is set. So the PHY
could then be used.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added functions for ack_interrupt and config_intr. Tested on an mpc5200b
powerpc board.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
this will allow to detect the link between the switch and the soc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mdio-gpio driver is probed via device trees, the platform
device id is set as -1, However the pdev->id is re-used as bus-id for
while creating mdio gpio bus.
So
For device tree case the mdio-gpio bus name appears as "gpio-ffffffff"
where as
for non-device tree case the bus name appears as "gpio-<bus-num>"
Which means the bus_id is fixed in device tree case, so we can't have
two mdio gpio buses via device trees. Assigning a logical bus number
via device tree solves the problem and the bus name is much consistent
with non-device tree bus name.
Without this patch
1. we can't support two mdio-gpio buses via device trees.
2. we should always pass gpio-ffffffff as bus name to phy_connect, very
different to non-device tree bus name.
So, setting up the bus_id via aliases from device tree is the right
solution and other drivers do similar thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-enables Energy Detect Power Down (EDPD) mode for the
LAN8710/LAN8720. EDPD mode was disabled in a previous commit,
(b629820d18), because it was causing the
PHY to not be able to detect a link when cold started without a cable
connected.
The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of
each other in order to set the ENERGYON bit and exit EDPD mode. If a
link partner does send the pulses within this interval, the PHY will
remained powered down.
This workaround will manually toggle the PHY on/off upon calls to
read_status in order to generate link test pulses if the link is down.
If a link partner is present, it will respond to the pulses, which will
cause the ENERGYON bit to be set and will cause the EDPD mode to be
exited.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit aa731872f7.
As pointed out by Ben Hutchings, this change is not correct.
mdiobus_unregister() can't be called if the bus isn't registered yet,
however this change can result in situations which cause that to
happen.
Part of the confusion here revolves around the fact that the
callers of this module control registration/unregistration,
rather than the module itself.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both these PHYs support interrupt generation on IC pin 32.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a phy_id sysfs attribute to MDIO devices, containing the
32-bit PHY identifier reported by the device. This attribute can
be useful when debugging problems related to phy drivers. Other
enumerable buses already have similar attributes.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on commit b27393aecf
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that of_mdio_find_bus() matches the prototype in the header (and
stop sparse complaining) by including the header with the prototype.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8710/LAN8720 chips do have broken the "FlexPWR" smart power-saving
capability. Enabling it leads to the PHY not being able to detect Link when
cold-started without cable connected. Thus, make sure this is disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christian Hohnstaedt <chohnstaedt@innominate.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper handling of the buggy revision A2 of LXT973 phy, adding
precautions linked to ERRATA Item 4:
Revision A2 of LXT973 chip randomly returns the contents of the previous even
register when you read a odd register regularly
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8021 PHY was previously caught by KS8051, which is not correct.
This PHY needs additional setup if it is strapped for address 0. In such
case an reserved bit must be written in the 0x16, "Operation Mode Strap
Override" register. According to the KS8051 datasheet, that bit means
"PHY Address 0 in non-broadcast" and it indeed behaves as such on KSZ8021.
The issue where the ethernet controller (Freescale FEC) did not communicate
with network is fixed by writing this bit as 1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP Hardware Clock devices appear as class devices in sysfs. This patch
changes the registration API to use the parent device, clarifying the
clock's relationship to the underlying device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver has no MODULE_LICENSE attribute in its source which
results in a kernel taint if I load this:
root@(none):~# modprobe bcm87xx
bcm87xx: module license 'unspecified' taints kernel.
Since the first lines of the source code clearly state:
* This file is subject to the terms and conditions of the GNU General
* Public License. See the file "COPYING" in the main directory of this
* archive for more details.
I think it's safe to add the MODULE_LICENSE("GPL") macro and thus remove
the kernel taint.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-mux-mmioreg.c uses function of_address_to_resource(), which is defined
in linux/of_address.h. This fixes a compilation error:
drivers/net/phy/mdio-mux-mmioreg.c: In function 'mdio_mux_mmioreg_probe':
drivers/net/phy/mdio-mux-mmioreg.c:83:2: error: implicit declaration of
function 'of_address_to_resource'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA. The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).
Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the way device tree support is added in mdio-gpio
driver. I found lot of code duplication which is not necessary.
Also strangely a new platform driver was also introduced for device tree
support. All this forced me to do this cleanup patch.
After this patch, the driver probe checks the of_node pointer to get the
data from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper functions which translate IEEE MDIO Manageable Device (MMD)
Energy-Efficient Ethernet (EEE) registers 3.20, 7.60 and 7.61 to and from
the comparable ethtool supported/advertised settings will be needed by
drivers other than those in PHYLIB (e.g. e1000e in a follow-on patch).
In the same fashion as similar translation functions in linux/mii.h, move
these functions from the PHYLIB core to the linux/mdio.h header file so the
code will not have to be duplicated in each driver needing MMD-to-ethtool
(and vice-versa) translations. The function and some variable names have
been renamed to be more descriptive.
Not tested on the only hardware that currently calls the related functions,
stmmac, because I don't have access to any. Has been compile tested and
the translations have been tested on a locally modified version of e1000e.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-mux driver scans all child mdio nodes, without regard to whether
the node is actually used. Some device trees include all possible
mdio-mux nodes and rely on the boot loader to disable those that are not
present, based on some run-time configuration. Those nodes need to be
skipped.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
Get the MDIO bus controller addresses from the device tree, small
clean up in use of devm_*
Remove, now unused, platform device setup code.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3938/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I no longer have a mailbox at smsc.com, and I've had two reports
that that email address now bounces from people trying to
contact me. This patch updates all references to that invalid
address to one that I can be contacted on more permanently.
This patch also updates the maintainer status to reflect
the fact I'm no longer directly paid to maintain these drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
With lockdep enabled we get:
=============================================
[ INFO: possible recursive locking detected ]
3.4.4-Cavium-Octeon+ #313 Not tainted
---------------------------------------------
kworker/u:1/36 is trying to acquire lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813da7e8>] mdio_mux_read+0x38/0xa0
but task is already holding lock:
(&bus->mdio_lock){+.+...}, at: [<ffffffff813d79e4>] mdiobus_read+0x44/0x88
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&bus->mdio_lock);
lock(&bus->mdio_lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
.
.
.
This is a false positive, since we are indeed using 'nested' locking,
we need to use mutex_lock_nested().
Now in theory we can stack multiple MDIO multiplexers, but that would
require passing the nesting level (which is difficult to know) to
mutex_lock_nested(). Instead we assume the simple case of a single
level of nesting. Since these are only warning messages, it isn't so
important to solve the general case.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
broadcom, not marvell.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If registering of one of them fails, all already registered drivers
of this module will be unregistered.
Use the new register/unregister functions in all drivers
registering more than one driver.
amd.c, realtek.c: Simplify: directly return registration result.
Tested with broadcom.c
All others compile-tested.
Signed-off-by: Christian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx phys don't support autonegotiation, so don't use it by
default, as otherwise phy_state_machine() will try to enable it (using
c22 requests, which also don't make any sense for the bcm78xx).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).
An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.
In the end, this patch also adds the EEE ethtool support implementing:
o phy_ethtool_set_eee
o phy_ethtool_get_eee
v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
values according to ethtool API (thanks to Ben's feedback).
Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
Fixed the phy_init_eee function: we need to check which link mode
was autonegotiated and then the corresponding bits in 7.60 and 7.61
registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/phy_device.c: In function ‘get_phy_device’:
drivers/net/phy/phy_device.c:340:14: warning: ‘phy_id’ may be used uninitialized in this function [-Wmaybe-uninitialized]
GCC can't see that when we return zero we always initialize
phy_id and that's the only path where we use it.
Initialize phy_id to zero to shut it up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for BCM8706 and BCM8727 devices. These are a 10Gig PHYs
which use MII_ADDR_C45 addressing. They are always 10G full duplex, so
there is no autonegotiation. All we do is report link state and send
interrupts when it changes.
If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow PHY drivers to supply their own device matching function
(match_phy_device()), or to be matched OF compatible properties.
PHYs following IEEE802.3 clause 45 have more than one device
identifier constants, which breaks the default device matching code.
Other 10G PHYs don't follow the standard manufacturer/device
identifier register layout standards, but they do use the standard
MDIO bus protocols for register access. Both of these require
adjustments to the PHY driver to device matching code.
If the there is an of_node associated with such a PHY, we can match it
to its driver using the "compatible" properties, just as we do with
certain platform devices. If the "compatible" property match fails,
first check if there is a driver supplied matching function, and if
not fall back to the existing identifier matching rules.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS. Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag. Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.
get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false. The follow-on patch to of_mdio.c will pass true where
appropriate.
EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
On a freescale imx6q platform, a hardware phy chip KSZ9021 is
recognized as a KS8001 chip by the current driver like this:
eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721]
KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id
0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't
distinguish them. So change phy_id_mask to resolve this problem.
Although the micrel datasheet says that the 4 LSB of phyid2 register
contains the chip revision number and the current driver is designed
to follow this rule, in reality the chip implementation doesn't follow
it.
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging style.
Add pr_fmt and missing newlines.
Remove embedded prefixes.
Neaten phy_print_status to avoid using KERN_CONT.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in drivers/net/phy:
Warning(drivers/net/phy/mdio_bus.c:109): No description found for parameter 'mdio_bus_np'
Warning(drivers/net/phy/mdio_bus.c:109): Excess function parameter 'mdio_np' description in 'of_mdio_find_bus'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the interrupt mask for IC101 A/G devices
and now enables the link/speed/duplex interrupts.
This is done by setting the "INTR pin used" bit and cleaning
all the other bits in the Register 17.
Reported-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only referenced from within phy_device.c, so there is
no reason to export it. In fact, we can make it static.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_OF_MDIO is tristate and will be m if PHYLIB is m. Use
IS_ENABLED macro to prevent build error:
ERROR: "of_mdio_find_bus" [drivers/net/phy/mdio-mux.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO pins select which sub bus is connected to the master.
Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a somewhat generic framework for MDIO bus
multiplexers. It is modeled on the I2C multiplexer.
The multiplexer is needed if there are multiple PHYs with the same
address connected to the same MDIO bus adepter, or if there is
insufficient electrical drive capability for all the connected PHY
devices.
Conceptually it could look something like this:
------------------
| Control Signal |
--------+---------
|
--------------- --------+------
| MDIO MASTER |---| Multiplexer |
--------------- --+-------+----
| |
C C
h h
i i
l l
d d
| |
--------- A B ---------
| | | | | |
| PHY@1 +-------+ +---+ PHY@1 |
| | | | | |
--------- | | ---------
--------- | | ---------
| | | | | |
| PHY@2 +-------+ +---+ PHY@2 |
| | | |
--------- ---------
This framework configures the bus topology from device tree data. The
mechanics of switching the multiplexer is left to device specific
drivers.
The follow-on patch contains a multiplexer driven by GPIO lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add of_mdio_find_bus() which allows an mii_bus to be located given its
associated the device tree node.
This is needed by the follow-on patch to add a driver for MDIO bus
multiplexers.
The of_mdiobus_register() function is modified so that the device tree
node is recorded in the mii_bus. Then we can find it again by
iterating over all mdio_bus_class devices.
Because the OF device tree has now become an integral part of the
kernel, this can live in mdio_bus.c (which contains the needed
mdio_bus_class structure) instead of of_mdio.c.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register() so
we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: netdev@vger.kernel.org
Acked-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
