Xbox One controllers that shipped with or were upgraded to the 2015
firmware discard the current rumble packets we send. This patch changes
the Xbox One rumble packet to a form that both the newer and older
firmware will accept.
It is based on changes made to support newer Xbox One controllers in
the SteamOS brewmaster-4.1 kernel branch.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
added the according id and incresed XPAD_PKT_LEN to 64 as the elite
controller sends at least 33 byte messages [1].
Verified to be working by [2].
[1]: https://franticrain.github.io/sniffs/XboxOneSniff.html
[2]: https://github.com/paroj/xpad/issues/23
Signed-off-by: Pierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS
ioctl needs to be treated with special care, as it has the pointer
size encoded in the command.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit e7ec014a47 ("Input: twl6040-vibra - update for device tree support")
made the separate vibra DT node to a subnode of the twl6040.
It now calls of_find_node_by_name() to locate the "vibra" subnode.
This function has a side effect to call of_node_put on() for the twl6040
parent node passed in as a parameter. This causes trouble later on.
Solution: we must call of_node_get() before of_find_node_by_name()
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
fix checkpatch.pl warning about 'Prefer 'unsigned int' to bare use of
'unsigned''
Signed-off-by: Clifton Barnes <clifton.a.barnes@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
NULL pointer derefence happens when booting with DTB because the
platform data for haptic device is not set in supplied data from parent
MFD device.
The MFD device creates only platform data (from Device Tree) for itself,
not for haptic child.
Unable to handle kernel NULL pointer dereference at virtual address 0000009c
pgd = c0004000
[0000009c] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(max8997_haptic_probe) from [<c03f9cec>] (platform_drv_probe+0x4c/0xb0)
(platform_drv_probe) from [<c03f8440>] (driver_probe_device+0x214/0x2c0)
(driver_probe_device) from [<c03f8598>] (__driver_attach+0xac/0xb0)
(__driver_attach) from [<c03f67ac>] (bus_for_each_dev+0x68/0x9c)
(bus_for_each_dev) from [<c03f7a38>] (bus_add_driver+0x1a0/0x218)
(bus_add_driver) from [<c03f8db0>] (driver_register+0x78/0xf8)
(driver_register) from [<c0101774>] (do_one_initcall+0x90/0x1d8)
(do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
(kernel_init_freeable) from [<c06bb5b4>] (kernel_init+0x8/0x114)
(kernel_init) from [<c0107938>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 104594b01c ("Input: add driver support for MAX8997-haptic")
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As pointed out by Richard, the changes to the comment got missed off
the absolute mode patch somehow.
Signed-off-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Complete() will be run with interrupt enabled, so change to
spin_lock_irqsave().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The CM109 driver reported key press events of volume up / down and
record / playback mute buttons, but no release events. Report those events
properly by handling volume and mute keys seperately. For the record and
playback mute buttons, only presses are registered by the CM109, therefore
simulate press-n-release. This fixes the volume control buttons of various
USB headsets.
Signed-off-by: Florian Euchner <florian.euchner@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since memory for a private data is allocated by kzalloc() there is no
need to fill it with zeroes immediately after the allocation.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bitwise shift operator has lower priority than plus operator. So the
values on macros should be enclosed in parentheses.
For example, "(1 << 4 + 1)" means "(1 << (4 + 1))", but it is not expected
by the macros.
And also fix other two coding style problems reported by
scripts/checkpatch.pl.
Signed-off-by: Rui Teng <rui.teng@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If using IRQF_TRIGGER_FALLING, then there is a race here: if the reset
completes before we enable the IRQ, then CHG is already low and touch
will be broken.
This has been seen on Chromebook Pixel 2.
A workaround is to reconfig T18 COMMSCONFIG to enable the RETRIGEN bit
using mxt-app:
mxt-app -W -T18 44
mxt-app --backup
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A wrong decoding of the touch coordinate message causes a wrong touch
ID. Touch ID for dual touch must be 0 or 1.
According to the actual Neonode nine byte touch coordinate coding,
the state is transported in the lower nibble and the touch ID in
the higher nibble of payload byte five.
Signed-off-by: Knut Wohlrab <Knut.Wohlrab@de.bosch.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The mutex does not seem to be needed. twl4030-vibra doesn't
use one either.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit c6f39257c9 ("mfd: twl6040: Use regmap for register cache")
did remove the private cache for the vibra control registers and replaced
access within twl6040_get_vibralr_status() by calls to regmap. This is OK,
as long as twl6040_get_vibralr_status() uses already cached values or is
not called from interrupt context. But we call this in vibra_play() for
checking that the vibrator is not configured for audio mode.
The result is a "BUG: scheduling while atomic" if the first use of the
twl6040 is a vibra effect, because the first fetch is by reading the
twl6040 registers through (blocking) i2c and not from the cache.
As soon as the regmap has cached the status, further calls are fine.
The solution is to move the condition to the work() function which
runs in context that can block.
The original code returns -EBUSY, but the return value of ->play()
functions is ignored anyways. Hence, we do not loose functionality
by not returning an error but just reporting the issue to INFO loglevel.
Tested-on: Pyra (omap5) prototype
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For devm-managed input devices we should not modify input device's parent,
otherwise automatic release of resources will not work properly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For devm-managed input devices we should not modify input device's parent,
otherwise automatic release of resources will not work properly.
Tested-by: "H. Nikolaus Schaller" <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Returning ret is wrong. And checking for an error as well. User space
may call multiple times until the work is really scheduled.
twl4030-vibra.c also ignores the return value.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
commit 21fb9f0d5e ("Input: twl6040-vibra - use system workqueue")
says that it switches to use the system workqueue but it did neither
- remove the workqueue struct variable
- replace code to really use the system workqueue
Instead it calls queue_work() on uninitialized info->workqueue.
The result is a NULL pointer dereference in vibra_play().
Solution: use schedule_work
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The trigger delay algorithm that converts from microseconds to
the register value looks incorrect. According to most of the PMIC
documentation, the equation is
delay (Seconds) = (1 / 1024) * 2 ^ (x + 4)
except for one case where the documentation looks to have a
formatting issue and the equation looks like
delay (Seconds) = (1 / 1024) * 2 x + 4
Most likely this driver was written with the improper
documentation to begin with. According to the downstream sources
the valid delays are from 2 seconds to 1/64 second, and the
latter equation just doesn't make sense for that. Let's fix the
algorithm and the range check to match the documentation and the
downstream sources.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 92d57a73e4 ("input: Add support for Qualcomm PMIC8XXX power key")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We shouldn't assign the parent device of the input_dev to be the
parent MFD device, because this will be used for devres which causes
input_unregister_device to run after the haptics device has been
removed, since it is itself a child of the MFD device. The default
of using the haptics device itself as the parent is correct.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In Cygnus SOC touch screen controller registers are shared with ADC and
flex timer. Using readl/writel could lead to race condition. So touch
screen driver is enhanced to support register access using syscon framework
API's to take care of mutually exclusive access.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of doing the dance with macro that either resolves to a pointer or
NULL, let's switch to using SIMPLE_DEV_PM_OPS().
Also let's mark suspend and resume methods as __maybe_unused instead of
guarding them with an #ifdef and rely on linker to drop unused code. Doing
so should allow better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit f799a3d8fe ("Input: omap-keypad:
Remove dependencies to mach includes") removed users of the above
functions, but left them in the code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As of 35f8679f57 ("Input: omap-keypad -
remove dead check") we no longer declare keypresses as spurious, therefore
we can use constant delay between scans.
Suggested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the VID/PID combination for the Xbox One version of the Mad
Catz FightStick TE 2.
The functionality that this provides is about on par with what the
Windows drivers for the stick manage to deliver.
What works:
- Digital stick
- 6 main buttons
- Xbox button
- The two buttons on the back
- The locking buttons (preventing accidental Xbox button press)
What doesn't work:
- Two of the main buttons (don't work on Windows either)
- The "Haptic" button setting does not have an effect (not sure if it
works on Windows)
I added the MAP_TRIGGERS_TO_BUTTONS option but in my (limited) testing
there was no practical difference with or without. The FightStick does
not have triggers though so adding it makes sense.
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device can now easily be derived from the interface.
Stop leaving a private copy.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device can now easily be derived from the interface.
Stop leaving a private copy.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device can now easily be derived from the interface.
Stop leaving a private copy.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device can now easily be derived from the interface.
Stop leaving a private copy.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The gtco driver expects at least one valid endpoint. If given malicious
descriptors that specify 0 for the number of endpoints, it will crash in
the probe function. Ensure there is at least one endpoint on the interface
before using it.
Also let's fix a minor coding style issue.
The full correct report of this issue can be found in the public
Red Hat Bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=1283385
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Merge fourth patch-bomb from Andrew Morton:
"A lot more stuff than expected, sorry. A bunch of ocfs2 reviewing was
finished off.
- mhocko's oom-reaper out-of-memory-handler changes
- ocfs2 fixes and features
- KASAN feature work
- various fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (42 commits)
thp: fix typo in khugepaged_scan_pmd()
MAINTAINERS: fill entries for KASAN
mm/filemap: generic_file_read_iter(): check for zero reads unconditionally
kasan: test fix: warn if the UAF could not be detected in kmalloc_uaf2
mm, kasan: stackdepot implementation. Enable stackdepot for SLAB
arch, ftrace: for KASAN put hard/soft IRQ entries into separate sections
mm, kasan: add GFP flags to KASAN API
mm, kasan: SLAB support
kasan: modify kmalloc_large_oob_right(), add kmalloc_pagealloc_oob_right()
include/linux/oom.h: remove undefined oom_kills_count()/note_oom_kill()
mm/page_alloc: prevent merging between isolated and other pageblocks
drivers/memstick/host/r592.c: avoid gcc-6 warning
ocfs2: extend enough credits for freeing one truncate record while replaying truncate records
ocfs2: extend transaction for ocfs2_remove_rightmost_path() and ocfs2_update_edge_lengths() before to avoid inconsistency between inode and et
ocfs2/dlm: move lock to the tail of grant queue while doing in-place convert
ocfs2: solve a problem of crossing the boundary in updating backups
ocfs2: fix occurring deadlock by changing ocfs2_wq from global to local
ocfs2/dlm: fix BUG in dlm_move_lockres_to_recovery_list
ocfs2/dlm: fix race between convert and recovery
ocfs2: fix a deadlock issue in ocfs2_dio_end_io_write()
...
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
The BYD PS/2 protocol driver now uses absolute reporting mode and
should behave more like other touchpads; Synaptics driver needed to
extend one of its quirks to a newer firmware version, and a few USB
drivers got tightened up checks for the contents of their descriptors"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sur40 - fix DMA on stack
Input: ati_remote2 - fix crashes on detecting device with invalid descriptor
Input: synaptics - handle spurious release of trackstick buttons, again
Input: synaptics-rmi4 - remove check of Non-NULL array
Input: byd - enable absolute mode
Input: ims-pcu - sanity check against missing interfaces
Input: melfas_mip4 - add hw_version sysfs attribute
INPUT_COMPAT_TEST became much simpler after commit f4056b5284
("input: redefine INPUT_COMPAT_TEST as in_compat_syscall()") so we can
cleanly eliminate it altogether.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During the initialisation the driver uses a buffer on the stack for DMA.
That violates the cache coherency rules. The fix is to allocate the buffer
with kmalloc().
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ati_remote2 driver expects at least two interfaces with one
endpoint each. If given malicious descriptor that specify one
interface or no endpoints, it will crash in the probe function.
Ensure there is at least two interfaces and one endpoint for each
interface before using it.
The full disclosure: http://seclists.org/bugtraq/2016/Mar/90
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The input compat code should work like all other compat code: for 32-bit
syscalls, use the 32-bit ABI and for 64-bit syscalls, use the 64-bit
ABI. We have a helper for that (in_compat_syscall()): just use it.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW6+LJAAoJEFGvii+H/Hdh8kQP/2AKYzPZiw9fhLufsDPvXO5m
BVdLYVyA11oQjQk7/Bh+5Rjz8mR5Tfv4uAJUReC3FOIfC/oJNBfBxYJLDV/P8S0/
KaCEaZrpNmecKrsy+TjmFYtcRa51THAdjlWEUKRks/ZBjwP4YsNnh5reWe+wB7bS
NFbCNhpXFvYXaDGH8MRhKqdChzZkxi+lgOBcFCKvUYO5/o6g/ZRUD/0TXUItJDwh
F8ps5jImHC1imHeRIKWPNrrZqcYasKmObIhvOKMDcwNQPnjrAWq5QuFH4LFhGQ7d
7NMQrBpaGvZyUNBVtL7ZF1xCJ68wAg/ZvZUkKVkax9ubLbSgf6VXYLQEbq+lyFn7
H9A79xPAGN2nC9HsGnCqW0c0qgTOz0DIkbpuaxAGlzBt0zooc19i3cuUd7LX0NG8
ttLaIP1hX6rgvXSFnF0Ihe3iN5A90LTT3ldbn3A8awyS42vEAbUVL9ivRL21BUbB
ilSTO2W05a9HlIVe43o2euytaGvDYX7RbL/g3WcJLF1pA01RCIDQAI5usMpgF3bf
fJ7cszll0OVTTb5UzbfrNsxAn4oNtbwMIspMMFe17pbmxqh+4oomM3CkuTrMVQfB
pA7Uv0jh/mLCV6P52ZEsNiecn0/l0rID8d/DCHjunr2xBWIOrglzZ7n+vLTJMNJ6
72GVBkYRMLbRm+eph1Tp
=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Pull input updates from Dmitry Torokhov:
"The most notable item is addition of support for Synaptics RMI4
protocol which is native protocol for all current Synaptics devices
(touchscreens, touchpads). In later releases we'll switch devices
using HID and PS/2 protocol emulation to RMI4.
You will also get:
- BYD PS/2 touchpad protocol support for psmouse
- MELFAS MIP4 Touchscreen driver
- rotary encoder was moved away from legacy platform data and to
generic device properties API, devm_* API, and can now handle
encoders using more than 2 GPIOs
- Cypress touchpad driver was switched to devm_* API and device
properties
- other assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
ARM: pxa/raumfeld: use PROPERTY_ENTRY_INTEGER to define props
Input: synaptics-rmi4 - using logical instead of bitwise AND
Input: powermate - fix oops with malicious USB descriptors
Input: snvs_pwrkey - fix returned value check of syscon_regmap_lookup_by_phandle()
MAINTAINERS: add devicetree bindings to Input Drivers section
Input: synaptics-rmi4 - add device tree support to the SPI transport driver
Input: synaptics-rmi4 - add SPI transport driver
Input: synaptics-rmi4 - add support for F30
Input: synaptics-rmi4 - add support for F12
Input: synaptics-rmi4 - add device tree support for 2d sensors and F11
Input: synaptics-rmi4 - add support for 2D sensors and F11
Input: synaptics-rmi4 - add device tree support for RMI4 I2C devices
Input: synaptics-rmi4 - add I2C transport driver
Input: synaptics-rmi4 - add support for Synaptics RMI4 devices
Input: ad7879 - add device tree support
Input: ad7879 - fix default x/y axis assignment
Input: ad7879 - move header to platform_data directory
Input: ts4800 - add hardware dependency
Input: cyapa - fix for losing events during device power transitions
Input: sh_keysc - remove dependency on SUPERH
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
