This patch somewhat combines two fixes to remote port handing in libfc.
The first problem was that rport work could be queued on a deleted
and freed rport. This is handled by not resetting rdata->event
ton NONE if the rdata is about to be deleted.
However, that fix led to the second problem, described by
Bhanu Gollapudi, as follows:
> Here is the sequence of events. T1 is first LOGO receive thread, T2 is
> fc_rport_work() scheduled by T1 and T3 is second LOGO receive thread and
> T4 is fc_rport_work scheduled by T3.
>
> 1. (T1)Received 1st LOGO in state Ready
> 2. (T1)Delete port & enter to RESTART state.
> 3. (T1)schdule event_work, since event is RPORT_EV_NONE.
> 4. (T1)set event = RPORT_EV_LOGO
> 5. (T1)Enter RESTART state as disc_id is set.
> 6. (T2)remember to PLOGI, and set event = RPORT_EV_NONE
> 6. (T3)Received 2nd LOGO
> 7. (T3)Delete Port & enter to RESTART state.
> 8. (T3)schedule event_work, since event is RPORT_EV_NONE.
> 9. (T3)Enter RESTART state as disc_id is set.
> 9. (T3)set event = RPORT_EV_LOGO
> 10.(T2)work restart, enter PLOGI state and issues PLOGI
> 11.(T4)Since state is not RESTART anymore, restart is not set, and the
> event is not reset to RPORT_EV_NONE. (current event is RPORT_EV_LOGO).
> 12. Now, PLOGI succeeds and fc_rport_enter_ready() will not schedule
> event_work, and hence the rport will never be created, eventually losing
> the target after dev_loss_tmo.
So, the problem here is that we were tracking the desire for
the rport be restarted by state RESTART, which was otherwise
equivalent to DELETE. A contributing factor is that we dropped
the lock between steps 6 and 10 in thread T2, which allows the
state to change, and we didn't completely re-evaluate then.
This is hopefully corrected by the following minor redesign:
Simplify the rport restart logic by making the decision to
restart after deleting the transport rport. That decision
is based on a new STARTED flag that indicates fc_rport_login()
has been called and fc_rport_logoff() has not been called
since then. This replaces the need for the RESTART state.
Only restart if the rdata is still in DELETED state
and only if it still has the STARTED flag set.
Also now, since we clear the event code much later in the
work thread, allow for the possibility that the rport may
have become READY again via incoming PLOGI, and if so,
queue another event to handle that.
In the problem scenario, the second LOGO received will
cause the LOGO event to occur again.
Reported-by: Bhanu Gollapudi <bprakash@broadcom.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In fnic_abort_cmd() and fnic_device_reset() assign `rport' earlier to make
FNIC_SCSI_DBG() calls cleaner.
In fnic_clean_pending_aborts() `rport' is not used.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
lport state is enum not bit mask.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
As per FC-BB-5 rev.2, section 7.8.7.1, strict ordering of FIP descriptors
is required for ELS requests. Also, look for missing and duplicate critical
descriptors.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear virtual link for NPIV ports is now handled by resetting
the matching vnport.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
As per FC-BB-5 rev 2, section 7.8.6.2, malformed FIP frame shall be
discarded. Drop discovery adv, ELS and CLV's with duplicate critical
descriptors.
[Resending after incorporating Joe's review comments]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow the D flag (indicating that keep-alives are not needed) to
be updated dynamically from received FIP advertisements.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
keep alives are disabled due to fd_flags set and also
stop updating keep alive values in that case.
Update select fcf time only if fcf is not already selected or
select time is not already determined from parse adv, and then
have select time cleared only once after fcf is selected.
Changed deadline check to time_after_eq() from time_after()
since now next timeout will be on exact 2.5 times FKA followed
by first advertisement.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[This patch has several improvements to the code in
the fip timers. It hasn't been tested yet.
I'm sending it out for review. Vasu, perhaps you can
merge this with your patch and test it together.]
The current code allows an advertisement to be used
even if it has been 3 times the FCF keep-alive
advertisement period (FKA) since one was received from
that FCF. The spec. calls for 2.5 times FKA.
Fix this and make sure we detect missed keep-alives promptly.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Resubmitting after incorporating Joe's review comment.
Unsolicited PRLO request is now handled by sending LS_ACC,
and then relogin to the remote port if an N-port login
session exists for that remote port.
Note that this patch should be applied on top of Joe Eykholt's
"Fix remote port restart problem" patch.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some old comments in fc_fcoe.h say TBD long after the
standard has been passed by T11. Clean them up.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
As per FC-LS Rev 1.62 table 46, response codes are handled as follows:
1. If the Req executed is true, PRLI is accepted.
2. If Req executed is not set, if resp code is 5,
PRLI is not retried and port is logged out.
3. If resp code is anything apart from 1 or 5, PRLI is retired
upto max retry count.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Retry upto max_rport_retry_count when a target responds with
LS_RJT for a PRLI request.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Host does not send discovery solicitation messages if Disc. Adv
from FCF are dropped. It restarts sending solicitation only
after receiving a Discovery Adv. from FCF. Fix is to restart
solicitation immediately after CVL processing.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Avoid infinite loop while processing FIP ELS or discovery
advertisement with non-critical descriptors.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A check in fcoe_ctlr_send_keep_alive() returns if there's no
port_id for the local port. This could miss a keep alive if
we just did a host reset and have logged off and will log back in.
Return only if we are doing the port keep alive, in which case
we need to be logged in.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A problem was found where the call to scsi_add_device() fails intermittently
for an adapter. This is caused when __scsi_add_device() returns -ENODEV as
a result of not calling scsi_probe_and_add_lun() since the call to
scsi_host_scan_allowed() fails. scsi_host_scan_allowed() fails because the
adapter state is set to SHOST_RECOVERY instead of SHOST_RUNNING. The state of
the adapter is being set to SHOST_RECOVERY by scsi_eh_scmd_add() during
error handling.
This problem is avoided by moving the setting of the allow_restart flag to
later in the device initialization sequence. This prevents further error
handling if we get a NOT_READY response from a TUR command by causing
scsi_check_sense() to return SUCCESS. Therefore, scsi_eh_scmd_add() will
not run and the adapter state will remain as SHOST_RUNNING.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
"phba" is always null here so we can't dereference it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
I added a kfree(pwrb_arr) in front of the return.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Compiling the driver will fail on 32 bit powerpc and other
architectures where writeq is not defined. This patch adds a
definition for writeq.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes 4 bugs in the connection connect/disconnect
cleanup path.
1. If beiscsi_open_conn fails beiscsi_free_ep was always being
called, and if beiscsi_open_conn failed because beiscsi_get_cid
failed then we would free an unallocated cid.
2. If beiscsi_ep_connect failed due to a beiscsi_open_conn failure
it was leaking iscsi_endpoints.
3. beiscsi_ep_disconnect was leaking iscsi_endpoints.
beiscsi_ep_disconnect should free the iscsi_endpoint. We cannot
do it in beiscsi_conn_stop because that is only called for
iscsi connection cleanup. If beiscsi_ep_connect returns
success, but then the poll function fails or the connect
times out then beiscsi_ep_disconnect will be called to clean
up the ep. The conn_stop callout will not be called in that path.
4. beiscsi_conn_stop was freeing the iscsi_endpoint then accessing
it a couple lines later.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fixed accounting of allocated SCSI buffers when post sgl fails.
- Restrict scsi buffer allocation based on LUN count (sdev_cnt).
- Create __lpfc_sli_free_rpi that doesn't take out the hbalock.
- Modify lpfc_sli_free_rpi to call __lpfc_sli_free_rpi.
- Call __lpfc_sli_free_rpi in lpfc_cleanup_pending_mbox.
- Do not swap the strings returned in mailbox commands and do
not swap byte aligned data in VPD.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Prevent unregistring of unused FCF when FLOGI is pending.
- Prevent point to point discovery on a FCoE HBA.
- Fixed FCF discovery failure after swapping FCoE port by
switching over to fast failover method when no FCF matches in-use FCF.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Allow enabling MSI-X intterupts with fewer vectors than requested
by looking at the return value from pci_enable_msix.
- Implemented driver PCI AER error handling routines for supporting
AER error recovering on SLI4 devices.
- Remove redundant SLI_ACTIVE checks
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. MSI-X interrupt support
2. Driver changes to support new maxRAID controller FW version. The
changes are mainly done to handle async notification changes done in
newer controller FW version.
3. Added state change notifications to notify applications of controller
states.
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Change the Max receive size on CIN FCFs to 0x800
- (From linux community) Check boundary before checking for NULL.
- Update last completion time for completed I/O to prevent heartbeat.
- Add Balius PCI Device IDs
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fix hba_queue_depth to reflect actual available XRIs
- Add support for new SLER specific firmware status codes.
- Free SCSI buffer when iotag allocation fails.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add poll or wait flag parameter to hba_init_link and hba_down_link.
- (From Linux Community) Make return with ENXIO negative.
- Remove unused INB code from driver.
- Prevent block_magmt_io from returning until mailbox is inactive.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Retry PLOGI up to 48 times when LS_RJT reason is
"Unable to supply requested data."
- When dev loss timeout occures do not change state if there
is an outstanding REG_LOGIN.
- Add logic to ignore REG_LOGIN completion if discovery is
restarted while waiting for REG_LOGIN.
- Only change state on REG_LOGIN completion if still in
state waiting for REG_LOGIN completion.
- Only send ADISCs to FCP-2 Targets (not Initiators).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A change in the hardware design of the chip for the new adapters changes the
default endianness of MMIO operations. This patch adds a register definition
which when written to with a predefined value will change the endianness
back to what the driver expects.
This patch also fixes two problems found during testing.
First, the first reserved field in the ipr_hostrcb64_fabirc_desc structure only
reserved one byte. The correct amount to reserve is 2 bytes.
Second, the reserved field of the ipr_hostrcb64_error structure only reserved
2 bytes. The correct amount to reserve is 16 bytes.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The function adpt_i2o_post_wait is called from several places, in some of
which, such as adpt_abort, a lock may be held.
The functions adpt_i2o_reparse_lct and adpt_i2o_lct_get are called from
several places, including adpt_rescan where a lock may be held.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@gfp exists@
identifier fn;
position p;
@@
fn(...) {
... when != spin_unlock_irqrestore
when any
GFP_KERNEL@p
... when any
}
@locked@
identifier gfp.fn;
@@
spin_lock_irqsave(...)
... when != spin_unlock_irqrestore
fn(...)
@depends on locked@
position gfp.p;
@@
- GFP_KERNEL@p
+ GFP_ATOMIC
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver was not unprotecting correctly, use correct bits
to unprotect the flash on ISP 82xx.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Outstanding mailbox commands, have no way to recover on f/w hung, and we
timeout on waiting for mbx response. This in turn affects the recovery process
as follows:
- We might already be in dpc while waiting for mbx to complete, so recovery for
that pci function will never get invoked. Reset Timeout (10 sec) is far less
than mbx timeout (30 sec).
- Other mbx cmds will get stuck due to serial mbx access.
Solution is to identify fw-hung scenario and handle outstanding mbx commands to
have an early-exit instead of waiting for response.
Other mbx commands waiting for access will also do an early-exit if fw-hung is
still applicable.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After topology change ISP is reset and VPs are re-enabled.
If the topology is not fabric, VPs could falsely get enabled.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Used bootloder address from FLT while loading FW from flash as well.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In case of both target and initiator capabilities reported by fc port,
the fc port port capability is made mutualy exclusive with priority given
for target capabilities.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* hold the hardware_lock throughout the duration of ctx-sp
timeout handling -- could result in use-after-free oops.
* retry a timed-out login-request.
* done() routines are called with the hardware-lock held, issue
qla2x00_mark_device_lost() with proper 'defer' flag.
* FCP2 capabilities are only relevant to target devices.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hold a reference to the srb (sp) while aborting an I/O -- as the
I/O can/will complete from within the interrupt-context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The TMFs used for pre-24xx ISPs incorrectly assumed 'cpu' tag
data could be valid. These chips have no multi-q/cpu-affinity
support. This corrects an oops seen on ISP23xx parts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This helps to correlate submission/completion messages during
triaging.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
