The hard-coded 10ms delay in mmc_power_up came from
commit 79bccc5aef ("mmc: increase power up delay"), which said "The TI
controller on Toshiba Tecra M5 needs more time to power up or the cards
will init incorrectly or not at all." But it's too engineering solution
for a special board but force all platforms to wait for that long time,
especially painful for mmc_power_up for eMMC when booting.
However, it's added since 2009, and we can't tell if other platforms
benefit from it. But in practise, the modern hardware are most likely to
have a stable power supply with 1ms after setting it for no matter PMIC
or discrete power. And more importnatly, most regulators implement the
callback of ->set_voltage_time_sel() for regulator core to wait for
specific period of time for the power supply to be stable, which means
once regulator_set_voltage_* return, the power should reach the the
minimum voltage that works for initialization. Of course, if there
are some other ways for host to power the card, we should allow them
to argue a suitable delay as well.
With this patch, we could assign the delay from firmware, or we could
assigne it via ->set_ios() callback from host drivers.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's implement the ->sw_reset() bus ops to allow SDIO func drivers, in
particular, to make a SW reset without doing a full power cycle of the SDIO
card.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().
Make the function internally available to the mmc core, as to allow the
following changes to make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.
However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.
To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.
The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_sdio_init_card() function has a couple of callers. In the
re-initialization cases, some additional reset commands are issued before
mmc_sdio_init_card() is called. As these additional reset commands are the
same, let's move these into a new static function, mmc_sdio_reinit_card()
and call mmc_sdio_init_card() from there. In this way we avoid the open
coding.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Allow to use tunable delay before detecting card after card is inserted,
which either comes from firmware node, or comes from debounce value
passed on to mmc_gpiod_request_cd(). If the platform doesn't support
debounce, then we fall back to use the debounce period as the delay,
otherwise, it behaves the same as before that a HW debounce(if set) plus
a 200ms hardcode delay before detecting the card.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Jennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: Diwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since RPMB area is accessible via special ioctl only and boot areas
are unlikely to contain any partitions, exclude them all from listing
in /proc/partitions. This will hide them from various user-level
software (e.g. fdisk), thus avoiding unnecessary access attempts.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.
Currently driver is using a VLA declared using the number of descriptors. This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values. Memory is
free'd before return from function.
>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.
It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
Upon module load, mmc_block allocates a bus with bus_registeri() in
mmc_blk_init(). This reference never gets freed during module unload, which
leads to subsequent re-insertions of the module fails and a WARN() splat is
triggered.
Fix the bug by dropping the reference for the bus in mmc_blk_exit().
Signed-off-by: Alexander Kappner <agk@godking.net>
Fixes: 97548575be ("mmc: block: Convert RPMB to a character device")
Cc: <stable@vger.kernel.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Update documentation for sdio_claim_irq to downgrade the wording
about doing recursive claims in an IRQ handler from 'must not' to
'should not'. This clarifies that recursive claims are supported,
but not the recommended (best) practice
Signed-off-by: Joel Cunningham <joel.cunningham@garmin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports the host capabilities to debugfs
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
[Harish: Added caps2, moved creation to mmc_add_host_debugfs]
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
In U-Boot, these cards are reported as
Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022 Manufact. date: 8/2015 (0x82) CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit
According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.
Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch exports RCA register to sysfs which will help in reading the
disk identification information.
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Variable err would be firstly initialized by the return value of
mmc_sd_switch().
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we could move card->host->caps & MMC_CAP_4_BIT_DATA
ahead of mmc_sdio_init_uhs_card, in mmc_host_uhs(). So there
we could save this bit to check that. Also, if the process of
sdio_enable_4bit_bus goes wrong, we should bails out early.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.
This breaks the platforms which could support UHS-I mode but on
some certain boards only support 1-bit mode with a UHS-I card inserted,
as all the tuning process is broken due to this. Alternatively, we
should check the return value from mmc_set_bus_width() to see if host
could finish the request to switch the bus width on its side. But that
needs more thing to do than this patch that just bails out early to try
high speed mode if 4-bit mode isn't available for whatever reason. And
this patch could also fix the same problem for sdio since R4_18V_PRESENT
won't be set for ocr when mmc_sdio_init_card() finds mmc_host_uhs()
is false.
Note that this patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card() since if the sd cards response with SD_ROCR_S18A,
it definitely supports UHS-I mode, which implicitly means these checkings
are always true.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However, users also want to
control it from sysfs power/wakeup attribute. That means the driver needs
to check the PM flags before enabling it in the suspend callback. Add
support for that in sdhci-pci, which is the only driver presently using the
MMC_CAP_CD_WAKE flag, and remove the enabling in mmc_gpiod_request_cd_irq()
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 03dbaa04a2 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.
Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Like mmc_can_gpio_cd(), mmc_can_gpio_ro() will also be useful for host
drivers to know whether GPIO write-protect detection is supported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the MMC_DRV_OP_GET_EXT_CSD request completes successfully, then
ext_csd must be freed, but in one case it was not. Fix that.
Signed-off-by: Liu Changcheng <changcheng.liu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.
After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.
The conditions here are:
1. During suspend, we reach mmc_pm_notify()
2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
-ENOSYS because btsdio_driver does not have a suspend method.
3. mmc_pm_notify() proceeds to remove the card
4. Upon resume, mmc_rescan() does nothing with this host, because of
the rescan_entered check which aims to only scan a non-removable
device a single time (i.e. during boot).
Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_alloc_req() is supposed to return error pointers but there is
one path where we forget to set the error code and accidentally return
NULL. The callers are not expecting that and will have a NULL pointer
dereference.
Fixes: 41e3efd07d ("mmc: block: Simplify cleaning up the queue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove config option MMC_MQ_DEFAULT and parameter mmc_use_blk_mq, so that
blk-mq must be used always.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.
Fixes: 9d4579a85c ("mmc: mmc_test: Disable Command Queue while mmc_test is used")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
Commands during non-blocking read - use Set Block Count (CMD23)
Commands during non-blocking write - use Set Block Count (CMD23)
mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().
Fixes: cb39f61e9b ("mmc: core: Export a few functions needed for blkmq support")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Calling getnstimeofday() can suffer from time jumps and from the
y2038 overflow, so it is not appropriate here. Using ktime_get_ts64()
solves both problems. Using ktime_get() with ktime_t timestamps would
also work, but it seems that we mainly want to print the times as
seconds+nanoseconds, so it would require an extra division in the output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function mmc_cqe_issue_type is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/mmc/core/queue.c:62:21: warning: symbol 'mmc_cqe_issue_type'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/core/block.c:2106:9-10: WARNING: return of 0/1 in function 'mmc_blk_status_error' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes:7eb43d537166 ("mmc: block: blk-mq: Stop using legacy recovery")
CC: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block driver's blk-mq paths do not use mmc_start_areq(). In order to
remove mmc_start_areq() entirely, start by removing it from mmc_test.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
There are only a few things the recovery needs to do. Primarily, it just
needs to:
Determine the number of bytes transferred
Get the card back to transfer state
Determine whether to retry
There are also a couple of additional features:
Reset the card before the last retry
Read one sector at a time
The legacy code spent much effort analyzing command errors, but commands
fail fast, so it is simpler just to give all command errors the same number
of retries.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Set a 10 second timeout for polling write request busy state. Note, mmc
core is setting a 3 second timeout for SD cards, and SDHCI has long had a
10 second software timer to timeout the whole request, so 10 seconds should
be ample.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>