Some implementations of SRIOV provide a capability structure
value of TotalVFs that is greater than what the software can support.
Provide a method to reduce the capability structure reported value
to the value the driver can support.
This ensures sysfs reports the current capability of the system,
hardware and software.
Example for its use: igb & ixgbe -- report 8 & 64 as TotalVFs,
but drivers only support 7 & 63 maximum.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Provide files under sysfs to determine the maximum number of VFs
an SR-IOV-capable PCIe device supports, and methods to enable and
disable the VFs on a per-device basis.
Currently, VF enablement by SR-IOV-capable PCIe devices is done
via driver-specific module parameters. If not setup in modprobe files,
it requires admin to unload & reload PF drivers with number of desired
VFs to enable. Additionally, the enablement is system wide: all
devices controlled by the same driver have the same number of VFs
enabled. Although the latter is probably desired, there are PCI
configurations setup by system BIOS that may not enable that to occur.
Two files are created for the PF of PCIe devices with SR-IOV support:
sriov_totalvfs Contains the maximum number of VFs the device
could support as reported by the TotalVFs register
in the SR-IOV extended capability.
sriov_numvfs Contains the number of VFs currently enabled on
this device as reported by the NumVFs register in
the SR-IOV extended capability.
Writing zero to this file disables all VFs.
Writing a positive number to this file enables that
number of VFs.
These files are readable for all SR-IOV PF devices. Writes to the
sriov_numvfs file are effective only if a driver that supports the
sriov_configure() method is attached.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Should make pci_create_sysfs_dev_files() simpler. Also fix possible
memleak in remove path.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Need type filled in device structure so it can be used for visible
attribute control in sysfs for pci_dev.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
* When hotplugging PCI devices in a PV guest we can allocate Xen-SWIOTLB later.
* Cleanup Xen SWIOTLB.
* Support pages out grants from HVM domains in the backends.
* Support wild cards in xen-pciback.hide=(BDF) arguments.
* Update grant status updates with upstream hypervisor.
* Boot PV guests with more than 128GB.
* Cleanup Xen MMU code/add comments.
* Obtain XENVERS using a preferred method.
* Lay out generic changes to support Xen ARM.
* Allow privcmd ioctl for HVM (used to do only PV).
* Do v2 of mmap_batch for privcmd ioctls.
* If hypervisor saves the LED keyboard light - we will now instruct the kernel
about its state.
Fixes:
* More fixes to Xen PCI backend for various calls/FLR/etc.
* With more than 4GB in a 64-bit PV guest disable native SWIOTLB.
* Fix up smatch warnings.
* Fix up various return values in privmcmd and mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQaY8qAAoJEFjIrFwIi8fJwPMH+gKngf4vSqrHjw+V2nsmeYaw
zrhRQrm3xV4BNR7yQHs+InDst/AJRAr0GjuReDK4BqDEzUfcFKvzalspdMGGqf+W
MUp+pMdN2S6649r/KMFfPCYcQvmIkFu8l76aClAqfA77SZRv1VL2Gn9eBxd82jS0
sWAUu5ichDSdfm/vAKXhdvhlKsK0hmihEbCM3+wRBoXEJX0kKbhEGn82smaLqkEt
uxWDJBT4nyYqbm6KVXQJ/WYCaWEmEImGSDb9J1WeqftGEn1Q55mpknvElkpNPE1b
Ifayqk50Kt43qnLk/AUrm8KFFlNKb73wTyAb0hVw7SQDcw1AcLa8ZdohLIZOl/4=
=prMY
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"Features:
- When hotplugging PCI devices in a PV guest we can allocate
Xen-SWIOTLB later.
- Cleanup Xen SWIOTLB.
- Support pages out grants from HVM domains in the backends.
- Support wild cards in xen-pciback.hide=(BDF) arguments.
- Update grant status updates with upstream hypervisor.
- Boot PV guests with more than 128GB.
- Cleanup Xen MMU code/add comments.
- Obtain XENVERS using a preferred method.
- Lay out generic changes to support Xen ARM.
- Allow privcmd ioctl for HVM (used to do only PV).
- Do v2 of mmap_batch for privcmd ioctls.
- If hypervisor saves the LED keyboard light - we will now instruct
the kernel about its state.
Fixes:
- More fixes to Xen PCI backend for various calls/FLR/etc.
- With more than 4GB in a 64-bit PV guest disable native SWIOTLB.
- Fix up smatch warnings.
- Fix up various return values in privmcmd and mm."
* tag 'stable/for-linus-3.7-x86-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (48 commits)
xen/pciback: Restore the PCI config space after an FLR.
xen-pciback: properly clean up after calling pcistub_device_find()
xen/vga: add the xen EFI video mode support
xen/x86: retrieve keyboard shift status flags from hypervisor.
xen/gndev: Xen backend support for paged out grant targets V4.
xen-pciback: support wild cards in slot specifications
xen/swiotlb: Fix compile warnings when using plain integer instead of NULL pointer.
xen/swiotlb: Remove functions not needed anymore.
xen/pcifront: Use Xen-SWIOTLB when initting if required.
xen/swiotlb: For early initialization, return zero on success.
xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used.
xen/swiotlb: Move the error strings to its own function.
xen/swiotlb: Move the nr_tbl determination in its own function.
xen/arm: compile and run xenbus
xen: resynchronise grant table status codes with upstream
xen/privcmd: return -EFAULT on error
xen/privcmd: Fix mmap batch ioctl error status copy back.
xen/privcmd: add PRIVCMD_MMAPBATCH_V2 ioctl
xen/mm: return more precise error from xen_remap_domain_range()
xen/mmu: If the revector fails, don't attempt to revector anything else.
...
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQac4hAAoJEPGMOI97Hn6zjZYP/iaqU9kjmgTsBbSyzB4oApv/
RRxo3I+ad9GF6XlMQfVAtyx1pgCD1gdGAtoDgGSCTqgdYD3CO10AxKU+yleAk1wo
dbMxLifJNTrT3G1mZ/NL16yEGhCwvhfwzRtB1VoZmCT4lSApO/7cJkXl2DzHfA/i
pmltOOiQCN8kbUcJbVPtUyTVPi2zl/8bsyCyTkS7YG0VXeGRM+ZUvPWZJ7MnWYYB
5qoCdrw5ENCCiDQ9yw5SAfgL23b+0p6OI/x3Lkex0QQOWwSqGSiaHt4b7eitrC5b
2eAJg32f/AzZke1YbKLMfdsL0VJP3GAswhDVHlgmo63rZkOZChm+97dgZ35Mcv5v
kEXkWyBb1xJ3t8rZir6Qer9Iv2wOB+MkZ5qtU/Vf+l0wLQLYTrRVsKngrEDREONk
dXbokp6iVSPeA1sTSdH9MmHlTUIj82ZLSGcxcjTsN8NWZjxx6g3rNx1uay+5MYOW
4ET9zNu5snrAqN6N4Tb81gvtG8qYfxzdvVfrA9AaGKI6xxB7jkqgFJRp55JiEcFc
x4cmWkhvdlhVsG2TQwFxYNfswOqD+7NCs6V4kSVZX6ezpDrH7I5VvcnnhstF7C8l
KZul0EV7OW+kDK23pNe24lVP2xtOv6G8eK/3PmeKIXWl1V83nqre/oLufRzTfs+Z
SxkILwY/MFpuCFteKE1t
=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
Commit 0d52f54e2e (PCI / ACPI: Make acpiphp
ignore root bridges using PCIe native hotplug) added code that made the
acpiphp driver completely ignore PCIe root complexes for which the kernel
had been granted control of the native PCIe hotplug feature by the BIOS
through _OSC. Later commit 619a5182d1
"PCI hotplug: Always allow acpiphp to handle non-PCIe bridges" relaxed
the constraints to allow acpiphp driver handle non-PCIe bridges under
such a complex. The constraint needs to be relaxed further to allow
acpiphp driver to handle PCIe ports without native PCIe hotplug capability.
Some MR-IOV switch chipsets, such PLX8696, support multiple virtual PCIe
switches and may migrate downstream ports among virtual switches. To
migrate a downstream port from the source virtual switch to the target, the
port needs to be hot-removed from the source and hot-added into the target.
The pciehp driver can't be used here because there are no slots within the
virtual PCIe switch. So acpiphp driver is used to support downstream port
migration. A typical configuration is as below:
[Root without native PCIe HP]
[Upstream port of vswitch without native PCIe HP]
[Downstream port of vswitch with native PCIe HP]
[PCIe endpoint]
Here acpiphp driver will be used to handle root ports and upstream port
in the virtual switch, and pciehp driver will be used to handle downstream
ports in the virtual switch.
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch changes .add/.remove interfaces of acpi_pci_driver.
In the current implementation acpi_handle is passed as a parameter
of .add/.remove interface. However, the acpi_pci_root structure
contains more useful information than just the acpi_handle. This
enables us to avoid some useless lookups in each acpi_pci_driver.
Note: This changes interfaces used by acpi_pci_register_driver(), an
exported symbol. This patch updates all the in-kernel users, but any
out-of-kernel acpi_pci_register_driver() users will need updates.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* stable/late-swiotlb.v3.3:
xen/swiotlb: Fix compile warnings when using plain integer instead of NULL pointer.
xen/swiotlb: Remove functions not needed anymore.
xen/pcifront: Use Xen-SWIOTLB when initting if required.
xen/swiotlb: For early initialization, return zero on success.
xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used.
xen/swiotlb: Move the error strings to its own function.
xen/swiotlb: Move the nr_tbl determination in its own function.
swiotlb: add the late swiotlb initialization function with iotlb memory
xen/swiotlb: With more than 4GB on 64-bit, disable the native SWIOTLB.
xen/swiotlb: Simplify the logic.
Conflicts:
arch/x86/xen/pci-swiotlb-xen.c
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This restores the previous behavior of stopping all child devices before
removing any of them. The current SR-IOV design, where removing the PF
also drops references on all the VFs, depends on having the VFs continue
to exist after having been stopped.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 433efd2247.
When we remove an SR-IOV device, we have this call chain:
driver .remove() method
pci_disable_sriov()
sriov_disable()
virtfn_remove()
pci_get_domain_bus_and_slot()
sriov_disable() is only called for PFs, not for VFs. When it's called
for a PF, it loops through all the VFs and calls virtfn_remove() for
each. But we stop and remove VFs before PFs, so by the time we get
to virtfn_remove(), the VFs have already been stopped and deleted
from the device list. Now pci_get_domain_bus_and_slot(), which uses
bus_find_device() and relies on that device list, doesn't find the
VFs, so the VF references aren't released correctly.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch (as1591) moves the pm_runtime_get_noresume() and
pm_runtime_put_sync() calls from __device_suspend() and
device_resume() to device_prepare() and device_complete() in the PM
core.
The reason for doing this is to make sure that parent devices remain
at full power (i.e., don't go into runtime suspend) while their
children are being resumed from a system sleep.
The PCI core already contained equivalent code to serve the same
purpose. The patch removes the duplicated code, since it is no longer
needed. One of the comments from the PCI core gets moved into the PM
core, and a second comment is added to explain whe the _get_noresume
and _put_sync calls are present.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Most architectures implement this in exactly the same way. Instead of
having each architecture duplicate this function, provide a single
implementation in the core and make it a weak symbol so that it can be
overridden on architectures where it is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the __init annotations in order to keep pci_fixup_irqs() around
after init (e.g. for hotplug). This requires the same change for the
implementation of pcibios_update_irq() on all architectures. While at
it, all __devinit annotations are removed as well, since they will be
useless now that HOTPLUG is always on.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Should use struct pci_bus_resource instead of struct pci_host_bridge_window
Commit 45ca9e9730 ("PCI: add helpers for building PCI bus resource lists")
added pci_free_resource_list() and used it in pci_bus_remove_resources().
Later it was also used for host bridge aperture lists, which was fine until
commit 0efd5aab41 ("PCI: add struct pci_host_bridge_window with CPU/bus
address offset"). That commit added offset information, so we needed a
struct pci_host_bridge_window that was separate from struct
pci_bus_resource.
Commit 0efd5aab41 should have split the host bridge aperture users of
pci_free_resource_list() from the pci_bus_resource user
(pci_bus_remove_resources()), but it did not.
[bhelgaas: changelog -- 0efd5aab41 was mine, so this is all my fault]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For bridges with "secondary > subordinate", i.e., invalid bus number
apertures, we don't enumerate anything behind the bridge unless the
user specified "pci=assign-busses".
This patch makes us automatically try to reassign the downstream bus
numbers in this case (just for that bridge, not for all bridges as
"pci=assign-busses" does).
We don't discover all the devices on the Intel DP43BF motherboard
without this change (or "pci=assign-busses") because its BIOS configures
a bridge as:
pci 0000:00:1e.0: PCI bridge to [bus 20-08] (subtractive decode)
[bhelgaas: changelog, change message to dev_info]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18412
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=625754
Reported-by: Brian C. Huffman <bhuffman@graze.net>
Reported-by: VL <vl.homutov@gmail.com>
Tested-by: VL <vl.homutov@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Function eeh_rmv_from_parent_pe() could be called by the path of
either normal PCI hotplug, or EEH recovery. For the former case,
we need purge the corresponding PE on removal of the associated
PE bus.
The patch tries to cover that by passing more information to function
pcibios_remove_pci_devices() so that we know if the corresponding PE
needs to be purged or be marked as "invalid".
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* pci/jiang-get-domain-bus-slot:
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
PCI: Use hotplug-safe pci_get_domain_bus_and_slot()
PCI/cpcihp: Use hotplug-safe pci_get_domain_bus_and_slot()
PCI/vga: Use hotplug-safe pci_get_domain_bus_and_slot()
ia64/PCI: Use hotplug-safe pci_get_domain_bus_and_slot()
This patch removes hardcoded sysfs attributes manipulation and
converts them into generic pci_bus->drv_attrs. This saves several bytes.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We piggyback on "xen/swiotlb: Use the swiotlb_late_init_with_tbl to init
Xen-SWIOTLB late when PV PCI is used." functionality to start up
the Xen-SWIOTLB if we are hot-plugged. This allows us to bypass
the need to supply 'iommu=soft' on the Linux command line (mostly).
With this patch, if a user forgot 'iommu=soft' on the command line,
and hotplug a PCI device they will get:
pcifront pci-0: Installing PCI frontend
Warning: only able to allocate 4 MB for software IO TLB
software IO TLB [mem 0x2a000000-0x2a3fffff] (4MB) mapped at [ffff88002a000000-ffff88002a3fffff]
pcifront pci-0: Creating PCI Frontend Bus 0000:00
pcifront pci-0: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
pci 0000:00:00.0: [8086:10d3] type 00 class 0x020000
pci 0000:00:00.0: reg 10: [mem 0xfe5c0000-0xfe5dffff]
pci 0000:00:00.0: reg 14: [mem 0xfe500000-0xfe57ffff]
pci 0000:00:00.0: reg 18: [io 0xe000-0xe01f]
pci 0000:00:00.0: reg 1c: [mem 0xfe5e0000-0xfe5e3fff]
pcifront pci-0: claiming resource 0000:00:00.0/0
pcifront pci-0: claiming resource 0000:00:00.0/1
pcifront pci-0: claiming resource 0000:00:00.0/2
pcifront pci-0: claiming resource 0000:00:00.0/3
e1000e: Intel(R) PRO/1000 Network Driver - 2.0.0-k
e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
e1000e 0000:00:00.0: Disabling ASPM L0s L1
e1000e 0000:00:00.0: enabling device (0000 -> 0002)
e1000e 0000:00:00.0: Xen PCI mapped GSI16 to IRQ34
e1000e 0000:00:00.0: (unregistered net_device): Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
e1000e 0000:00:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1b:21🆎c6:13
e1000e 0000:00:00.0: eth0: Intel(R) PRO/1000 Network Connection
e1000e 0000:00:00.0: eth0: MAC: 3, PHY: 8, PBA No: E46981-005
The "Warning only" will go away if one supplies 'iommu=soft' instead
as we have a higher chance of being able to allocate large swaths of
memory.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
* pci/trivial:
PCI: Drop duplicate const in DECLARE_PCI_FIXUP_SECTION
PCI: Drop bogus default from ARCH_SUPPORTS_MSI
PCI: cpqphp: Remove unreachable path
PCI: Remove bus number resource debug messages
PCI/AER: Print completion message at KERN_INFO to match starting message
PCI: Fix drivers/pci/pci.c kernel-doc warnings
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
Following code has a race window between pci_find_bus() and pci_get_slot()
if PCI hotplug operation happens between them which removes the pci_bus.
So use PCI hotplug safe interface pci_get_domain_bus_and_slot() instead,
which also reduces code complexity.
struct pci_bus *pci_bus = pci_find_bus(domain, busno);
struct pci_dev *pci_dev = pci_get_slot(pci_bus, devfn);
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Following code has a race window between pci_find_bus() and pci_get_slot()
if PCI hotplug operation happens between them which removes the pci_bus.
So use PCI hotplug safe interface pci_get_domain_bus_and_slot() instead,
which also reduces code complexity.
struct pci_bus *pci_bus = pci_find_bus(domain, busno);
struct pci_dev *pci_dev = pci_get_slot(pci_bus, devfn);
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Following code has a race window between pci_find_bus() and pci_get_slot()
if PCI hotplug operation happens between them which removes the pci_bus.
So use PCI hotplug safe interface pci_get_domain_bus_and_slot() instead,
which also reduces code complexity.
struct pci_bus *pci_bus = pci_find_bus(domain, busno);
struct pci_dev *pci_dev = pci_get_slot(pci_bus, devfn);
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
* 'x86/platform' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (9690 commits)
x86: Document x86_init.paging.pagetable_init()
x86: xen: Cleanup and remove x86_init.paging.pagetable_setup_done()
x86: Move paging_init() call to x86_init.paging.pagetable_init()
x86: Rename pagetable_setup_start() to pagetable_init()
x86: Remove base argument from x86_init.paging.pagetable_setup_start
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
...
The original idea comes from Ram Pai. This patch puts the chunk of
code for calculating the minimal alignment of memory window into a
separate inline function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch changes pbus_size_io() and pbus_size_mem() to do window (I/O,
memory and prefetchable memory) reassignment based on the minimal
alignments for the P2P bridge, which was retrieved by window_alignment().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch implements a weak function to return the default I/O or memory
window alignment for a P2P bridge. By default, I/O windows are aligned to
4KiB or 1KiB and memory windows are aligned to 4MiB. Some platforms, e.g.,
powernv, have special alignment requirements and can override
pcibios_window_alignment().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Options without prompts and without dependencies don't usefully have a
default value - they're intended to be selected from other options
only.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
register & 0x0B == 0x04 is never true, the code will always take the
(identical) 0x00 path anyway. Remove the dead code paths.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=44151
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In function pci_get_subsys() there is a check:
/*
* pci_find_subsys() can be called on the ide_setup() path,
* super-early in boot. But the down_read() will enable local
* interrupts, which can cause some machines to crash. So here we
* detect and flag that situation and bail out early.
*/
if (unlikely(no_pci_devices()))
return NULL;
But there is no ide_setup() now, and no down_read() either, which
makes the check obsolete. So remove it.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the driver ignored resume unless the pciehp_force module_param
was specified. On some laptops that means that interrupts are not
delivered after S3, so card removals and insertions are not handled.
This patch makes the driver handle resume regardless of pciehp_force.
[bhelgaas: changelog]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Since pci_error_handlers is just a function table make it const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
