ACPI ATIF has a function called query
backlight transfer characteristics. Among the
information returned by this function is
the minimum and maximum input signals for the
backlight
Call that function on ACPI init. When DM
backlight device is updated, copy over the
backlight caps into DM, but only once. Use
the backlight caps in the backlight-to-dc
calculation
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adaptive Backlight Management (ABM) is a feature
that reduces backlight level to save power, while
increasing pixel contrast and pixel luminance
to maintain readability and image quality.
ABM will adjust in response to the
pixel luminance of the displayed content.
ABM is made available as a drm property on eDP
monitors called "abm level", which ranges from 0 to 4.
When this property is set to 0, ABM is off. Levels 1
to 4 represent different ranges of backlight reduction.
At higher levels both the backlight reduction and pixel
adjustment will be greater.
ABM requires DMCU firmware, which is currently available for
Raven ASICs only. If the feature does not work, please
ensure your firmware is up to date.
v2:
Fix commit message, only attach property if DMCU loaded
v3:
Store ABM level in crtc state to accommodate dc
v4:
Fix ABM saving on dpms cycle
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMCU IRAM must be loaded by the driver before DMCU
can function.
Move the IRAM code out of the shadows and into a new file
modules/power/power_helpers.c
The IRAM table contains the backlight curve and ABM parameters
Add this new file to the Makefiles
Call dmcu_load_iram in late init of DM
Move struct dmcu_version from dc.h to dmcu.h to allow
dmcu to be included on its own
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before:
We use drm_match_cea_mode() to get the vic for any mode we
want to set, most of the time vic will be different for the new mode.
DC uses memcmp to check if timing changed, in this case DC will
say timing changed and we endup doing a full modeset.
Current:
Now we check if !RMX_OFF and old_refresh == new_refresh if so
we copy the vic from old timing. In a case where we are currently on
a lower timing and want to change to higher mode, stream->dst will be
different and cause us to do a full modeset, which is what we want.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Setting this allows for display scaling by default
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dm_services_types.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.
Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.
This should be a user configurable option such that the user can select
what bpc configuration they would like.
[How]
This patch adds support for getting and setting the amdgpu driver
specific "max bpc" property on the connector.
It also adds support for limiting the output bpc based on the property
value. The default limitation is the lowest value in the range, 8bpc.
This was the old value before the range was uncapped.
This patch should be updated/replaced later once common drm support
for max bpc lands.
Bugzilla: https://bugs.freedesktop.org/108542
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201585
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200645
Fixes: e03fd3f300 ("drm/amd/display: Do not limit color depth to 8bpc")
v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New features for 4.21:
amdgpu:
- Support for SDMA paging queue on vega
- Put compute EOP buffers into vram for better performance
- Share more code with amdkfd
- Support for scanout with DCC on gfx9
- Initial kerneldoc for DC
- Updated SMU firmware support for gfx8 chips
- Rework CSA handling for eventual support for preemption
- XGMI PSP support
- Clean up RLC handling
- Enable GPU reset by default on VI, SOC15 dGPUs
- Ring and IB test cleanups
amdkfd:
- Share more code with amdgpu
ttm:
- Move global init out of the drivers
scheduler:
- Track if schedulers are ready for work
- Timeout/fault handling changes to facilitate GPU recovery
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114165113.3751-1-alexander.deucher@amd.com
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=UV0m
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
[why]
It is not correct to touch aconnector within atomic_check.
[How]
It was added as workaround before, and no longer needed.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the dc_config properly when the option is enabled.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is not correct to touch aconnector within atomic_check.
[How]
It was added as workaround before, and no longer needed.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the dc_config properly when the option is enabled.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_plane_cleanup does not free the plane.
[How]
Call drm_primary_helper_destroy which will also free the plane.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 0cafc82fae.
This breaks some apps that assume 0 is minimum brightness.
Revert for 4.20. This is fixed properly for drm-next/4.21 in:
"drm/amd: Don't fail on backlight = 0"
However, that patch depends on more extensive changes to the
backlight interface which are too invasive for -fixes.
Fixes: Bugzilla: https://bugs.freedesktop.org/108668
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_plane_cleanup does not free the plane.
[How]
Call drm_primary_helper_destroy which will also free the plane.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Amgpu's backlight update status function was
returning 1 (an error value) when the backlight
property was 0. This breaks users that assume
0 is a valid backlight value (which is a
correct assumption)
If the user passes in a backlight value of 0,
tell them everything is fine, then write a value of
1 to hardware.
Signed-off-by: David Francis <David.Francis@amd.com>
Bugzilla: https://bugs.freedesktop.org/108668
Fixes: 416615ea9578 ("drm/amd/display: set backlight level limit to 1")
Cc: Suresh.Guttula@amd.com
Cc: Harry.Wentland@amd.com
Cc: Samantham@posteo.net
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] We want to increase precision for backlight setting.
But DC interface takes 8 bit backlight level value only.
[How] DMCU already takes 16 bit backlight level.
Expand the DC interface to take 16.16 bit value.
Max 32 bit backlight value (0xFFFF) will represent
max backlight (100%)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Documentation is helpful for the community to understand our code.
This change does some high-level documentation of some DM interfaces
with DRM, and the amdgpu base driver.
[How]
An entry for AMDgpu DC has been added to Documentation/gpu/drivers.rst
TOC. amdgpu-dc.rst is created to pull in inline doc-strings, which:
- Provides an overview for "What is DM?"
- Documents AMDgpu DM lifecyle
- Documents IRQ management
- Documents atomic_check and commit_tail interfaces
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need separate feature flag for DP 4:2:0 support, since existing
flag is used for HDMI
[How]
Added dp_ycbcr420_supported to struct encoder_feature_support
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch will work as workaround for silicon limitation
related to PWM dutycycle when the backlight level goes to 0.
Actually PWM value is 16 bit value and valid range from 1-65535.
when ever user requested to set this PWM value to 0 which is not
fall in the range, in VBIOS taken care this by limiting to 1.
This patch here will do the same. Either driver or VBIOS can not
pass 0 value as it is not a valid range for PWM and it will
give a high PWM pulse which is not the intended behaviour as
per HW constraints.
Signed-off-by: suresh guttula <suresh.guttula@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
4.19 is out, Lyude asked for a backmerge, and it's been a while. All
very good reasons on their own :-)
Signed-off-by: Sean Paul <seanpaul@chromium.org>
In amdgpu_dm_commit_tail(), wait until flip_done() is signaled before
we signal hw_done().
[Why]
This is to temporarily address a paging error that occurs when a
nonblocking commit contends with another commit, particularly in a
mirrored display configuration where at least 2 CRTCs are updated.
The error occurs in drm_atomic_helper_wait_for_flip_done(), when we
attempt to access the contents of new_crtc_state->commit.
Here's the sequence for a mirrored 2 display setup (irrelevant steps
left out for clarity):
**THREAD 1** | **THREAD 2**
|
Initialize atomic state for flip |
|
Queue worker |
...
| Do work for flip
|
| Signal hw_done() on CRTC 1
| Signal hw_done() on CRTC 2
|
| Wait for flip_done() on CRTC 1
<---- **PREEMPTED BY THREAD 1**
Initialize atomic state for cursor |
update (1) |
|
Do cursor update work on both CRTCs |
|
Clear atomic state (2) |
**DONE** |
...
|
| Wait for flip_done() on CRTC 2
| *ERROR*
|
The issue starts with (1). When the atomic state is initialized, the
current CRTC states are duplicated to be the new_crtc_states, and
referenced to be the old_crtc_states. (The new_crtc_states are to be
filled with update data.)
Some things to note:
* Due to the mirrored configuration, the cursor updates on both CRTCs.
* At this point, the pflip IRQ has already been handled, and flip_done
signaled on all CRTCs. The cursor commit can therefore continue.
* The old_crtc_states used by the cursor update are the **same states**
as the new_crtc_states used by the flip worker.
At (2), the old_crtc_state is freed (*), and the cursor commit
completes. We then context switch back to the flip worker, where we
attempt to access the new_crtc_state->commit object. This is
problematic, as this state has already been freed.
(*) Technically, 'state->crtcs[i].state' is freed, which was made to
reference old_crtc_state in drm_atomic_helper_swap_state()
[How]
By moving hw_done() after wait_for_flip_done(), we're guaranteed that
the new_crtc_state (from the flip worker's perspective) still exists.
This is because any other commit will be blocked, waiting for the
hw_done() signal.
Note that both the i915 and imx drivers have this sequence flipped
already, masking this problem.
Signed-off-by: Shirish S <shirish.s@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For atomic driver this is the default, no need to reimplement it. We
still need to keep the copypasta for not-atomic drivers though, since
no one polished the legacy crtc helpers as much as the atomic ones.
v2: amdgpu uses ->best_encoder internally, give it a local copy. It
might be a good idea to merge the connector and encoder into one
amdgpu_dm_sink structure, that might match DC internals better. At
least for non-DPMST outputs. Kudos to Ville for spotting this.
v3: Rebase onto a487411a64 ("drm/amd/display: Use DRM helper for
best_encoder").
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: Tony Cheng <Tony.Cheng@amd.com>
Cc: "Leo (Sunpeng) Li" <sunpeng.li@amd.com>
Cc: Shirish S <shirish.s@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004202446.22905-2-daniel.vetter@ffwll.ch
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
BackMerge v4.19-rc6 into drm-next
I have some pulls based on rc6, and I prefer to have an explicit backmerge.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.
[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Everything that isn't related to the IH ring.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The work struct's schedule call was removed a while ago, making this
useless.
[How]
Remove it.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During suspend under some hardware configurations can result in a
series of atomic commits with a NULL stream status - which
causes a NULL pointer dereference. This should be guarded.
[How]
Exit early from the function - if we can't access the stream then
there isn't anything that can be done here.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Parse the native color bit and send it to freesync module for future
use
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a new pull for drm-next on top of last weeks with the following
changes:
- Fixed 64 bit divide
- Fixed vram type on vega20
- Misc vega20 fixes
- Misc DC fixes
- Fix GDS/GWS/OA domain handling
Previous changes from last week:
amdgpu/kfd:
- Picasso (new APU) support
- Raven2 (new APU) support
- Vega20 enablement
- ACP powergating improvements
- Add ABGR/XBGR display support
- VCN JPEG engine support
- Initial xGMI support
- Use load balancing for engine scheduling
- Lots of new documentation
- Rework and clean up i2c and aux handling in DC
- Add DP YCbCr 4:2:0 support in DC
- Add DMCU firmware loading for Raven (used for ABM and PSR)
- New debugfs features in DC
- LVDS support in DC
- Implement wave kill for gfx/compute (light weight reset for shaders)
- Use AGP aperture to avoid gart mappings when possible
- GPUVM performance improvements
- Bulk moves for more efficient GPUVM LRU handling
- Merge amdgpu and amdkfd into one module
- Enable gfxoff and stutter mode on Raven
- Misc cleanups
Scheduler:
- Load balancing support
- Bug fixes
ttm:
- Bulk move functionality
- Bug fixes
radeon:
- Misc cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920150438.12693-1-alexander.deucher@amd.com
[Why]
It's not being used anymore.
[How]
Nuke it
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Treat them all as Raven rather than adding a new picasso
asic type. This simplifies a lot of code and also handles the
case of rv2 chips with the 0x15d8 pci id. It also fixes dmcu
fw handling for picasso.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Read the version number from the common firmware header and store
it in the dm struct
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for picasso to the display manager.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
After GPU reset pflip completion IRQ is disabled and hence
any subsequent mode set or plane update leads to hang.
Fix:
Unless acrtc->otg_inst is initialized to -1 during display
block initializtion then durng resume from GPU reset
amdgpu_irq_gpu_reset_resume_helper will override CRTC 0 pflip
IRQ value with whatever value was on every other unused CRTC because
dm_irq_state will do irq_source = dal_irq_type + acrtc->otg_inst
where acrtc->otg_inst will be 0 for every unused CRTC.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMCU (Display Microcontroller Unit) is a GPU chip involved in
eDP features like Adaptive Backlight Modulation and Panel Self
Refresh.
DC is already fully equipped to initialize DMCU as long as the
firmware is loaded.
At the moment only the raven firmware is available.
A single .bin file is loaded by the kernel's loading mechanism
and split into two ucodes according to the header.
DMCU is optional, so if the firmware is not found, no error or
warning is raised.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Our implementation is functionally identical to DRM's
Note that instead of checking if the provided id is 0, the helper
follows through with the mode object search. However, It will still
return NULL, since 0 is not a valid object id, and missed searches
will return NULL.
[How]
Remove our implementation, and replace it with
drm_atomic_helper_best_encoder.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We currently lock modeset by setting a boolean in dm. We want to lock
Based on what DC tells us.
[How]
Build stream_updates and plane_update based on what changed. Then we
call check_update_surfaces_for_stream() to get the update type
We lock only if update_type is not fast
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Good spelling and grammar makes comments
more pleasant and clearer.
Linux has coding standards for comments
that we should try to follow.
[How]
Fix obvious spelling and grammar issues
Ensure all comments use '/*' and '*/' and multi-line comments
follow linux convention
Remove line-of-stars comments that do not separate sections
of code and comments referring to lines of code that have
since been removed
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We have logging methods for printing hardware state for newer ASICs
but no way to trigger the log output.
[How]
Add support for triggering the output via writing to a debugfs file
entry. Log output currently goes into dmesg for convenience, but
accessing via a read should be possible later.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm_handle_vblank is deprecated. Use drm_crtc_handle_vblank instead.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds support for LVDS displays.
v2: add support for spread spectrum, sink detect
v3: clean up enable_lvds_output
v4: fix up link_detect
v5: remove assert on 888 format
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105880
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I2C code did not match dc resource model and was generally
unpleasant
[How]
Move code into new svelte dce_i2c files, replacing various i2c
objects with two structs: dce_i2c_sw and dce_i2c_hw. Fully split
sw and hw code paths. Remove all redundant declarations. Use
address lists to distinguish between versions. Change dce80 code
to newer register access macros.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dependency on internal sink map and instead
use existing stream and plane state
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
