This removes the need to use IRQ safe spinlocks in many places.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
_rtl_pci_rx_interrupt uses rtlpci->rx_ring[rx_queue_idx].idx a
few times, so store it in a separate variable.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
set_rfpowerstate_inprogress is only set and never read
so remove it.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This make sure any IRQ handlers running on other CPUs complete.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch to advertise interface combinations
worked by pure luck in the P2P case, but all
other cases are broken. This is due to a dumb
mistake in the code that checks what should
be advertised, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple A-MPDU actions will received from mac80211 while setting up the
aggregation queue, change the message log to better represent the states.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Aggregation will not enable if the traffic is lower than the threshold,
this is not an error condition, so change the logging level.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this, iwlwifi will advertise the limits on
concurrency of virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a memory leak in case request_irq fails.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The exact same error message is used in three different functions in
iwlagn. Add the function name to the error string to disambiguate where
the error is coming from.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove local variable that was shadowing another one
sta_priv hasn't changed since the beginning of the function, so don't define
another pointer with the same name to the same variable
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PAN context has three states: disabled, disassociated
and associated. It seems that wasn't quite as much of an
issue in previous versions of the microcode, but now we
really have to use all the three states properly. So add
code to switch accordingly.
Additionally, PAN parameters need to be sent differently
and the timing for PAN RXON needs to be inbetween.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All agn devices use the same tx power function, remove the ops
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During channge channel, tx power will not send to uCode, the tx power command
should send after scan complete. but should also can send after RXON command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the training power calculation indirectly depends on target power under
some scenarios, unless we have a valid training power, the PAPRD frames
won't be sent out. so when we get an invalid training power, its better
to display them before returning back.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this helps the user to start/stop ANI dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix ensure the timers to be set at beacon interval boundaries.
Without this change timers can be set improperly resulting in the absence of beacons.
Signed-off-by: Fabrice Deyber <fabricedeyber@agilemesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In PAPRD table initialization path we do some register read, so
make sure the chip is awake during that. Currently PAPRD is disabled.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As suggested by Mike McCormack <mikem@ring3k.org> for rtl8192ce, make sure any IRQ
handlers running on other CPUs complete.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As noted by Mike McCormack <mikem@ring3k.org> for rtl8192ce, make sure
all updates to a descriptor are flushed to memory before assigning ownship
to hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For SD8787 A0/A1 chipsets we use the default firmware image
file 'mrvl/sd8787_uapsta.bin'. So the chip rev id variable
is removed.
The global variable fw_name is moved to adapter structure
so that we can support a different interface, such as PCIe,
in future.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for b43legacy:
CC [M] drivers/net/wireless/b43legacy/main.o
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_request_firmware’:
drivers/net/wireless/b43legacy/main.c:1567:6: warning: variable ‘tmshigh’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_dev_config’:
drivers/net/wireless/b43legacy/main.c:2637:6: warning: variable ‘antenna_rx’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_bss_info_changed’:
drivers/net/wireless/b43legacy/main.c:2778:24: warning: variable ‘phy’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/xmit.c: In function ‘generate_txhdr_fw3’:
drivers/net/wireless/b43legacy/xmit.c:324:7: warning: variable ‘rts_rate_ofdm’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/b43legacy/dma.o
drivers/net/wireless/b43legacy/dma.c: In function ‘free_all_descbuffers’:
drivers/net/wireless/b43legacy/dma.c:820:36: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/dma.c: In function ‘b43legacy_dma_tx’:
drivers/net/wireless/b43legacy/dma.c:1377:28: warning: variable ‘info’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/dma.c:1374:24: warning: variable ‘hdr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43legacy/dma.c: In function ‘b43legacy_dma_handle_txstatus’:
drivers/net/wireless/b43legacy/dma.c:1438:36: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192se:
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/dm.o
drivers/net/wireless/rtlwifi/rtl8192se/dm.c: In function ‘_rtl92s_dm_refresh_rateadaptive_mask’:
drivers/net/wireless/rtlwifi/rtl8192se/dm.c:225:5: warning: variable ‘rssi_level’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/fw.o
drivers/net/wireless/rtlwifi/rtl8192se/fw.c: In function ‘rtl92s_download_fw’:
drivers/net/wireless/rtlwifi/rtl8192se/fw.c:361:6: warning: variable ‘file_length’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/hw.o
drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘_rtl92se_hw_configure’:
drivers/net/wireless/rtlwifi/rtl8192se/hw.c:887:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘_rtl92se_set_media_status’:
drivers/net/wireless/rtlwifi/rtl8192se/hw.c:1125:20: warning: variable ‘ledaction’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘rtl92se_gpio_radio_on_off_checking’:
drivers/net/wireless/rtlwifi/rtl8192se/hw.c:2274:32: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/phy.o
drivers/net/wireless/rtlwifi/rtl8192se/phy.c: In function ‘rtl92s_phy_set_bw_mode’:
drivers/net/wireless/rtlwifi/rtl8192se/phy.c:266:5: warning: variable ‘reg_prsr_rsc’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192se/trx.o
drivers/net/wireless/rtlwifi/rtl8192se/trx.c: In function ‘_rtl92se_translate_rx_signal_stuff’:
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:584:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192cu:
CC [M] drivers/net/wireless/rtlwifi/rtl8192cu/mac.o
drivers/net/wireless/rtlwifi/rtl8192cu/mac.c: In function ‘rtl92c_translate_rx_signal_stuff’:
drivers/net/wireless/rtlwifi/rtl8192cu/mac.c:1116:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192ce:
CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/hw.o
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c: In function ‘_rtl92ce_hw_configure’:
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:766:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c: In function ‘rtl92ce_gpio_radio_on_off_checking’:
drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:1972:41: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/phy.o
drivers/net/wireless/rtlwifi/rtl8192ce/phy.c: In function ‘rtl92c_phy_config_rf_with_headerfile’:
drivers/net/wireless/rtlwifi/rtl8192ce/phy.c:284:7: warning: variable ‘rtstatus’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/trx.o
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c: In function ‘_rtl92ce_translate_rx_signal_stuff’:
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:595:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtl8192c-common:
CC [M] drivers/net/wireless/rtlwifi/rtl8192c/fw_common.o
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: In function ‘_rtl92c_cmd_send_packet’:
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:549:5: warning: variable ‘own’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/rtl8192c/phy_common.o
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c: In function ‘_rtl92c_phy_iq_calibrate’:
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1256:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c: In function ‘rtl92c_phy_iq_calibrate’:
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1766:6: warning: variable ‘reg_ecc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1765:34: warning: variable ‘reg_eac’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for rtlwifi:
CC [M] drivers/net/wireless/rtlwifi/base.o
drivers/net/wireless/rtlwifi/base.c: In function ‘rtl_tx_agg_stop’:
drivers/net/wireless/rtlwifi/base.c:891:23: warning: variable ‘tid_data’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/base.c: In function ‘rtl_tx_agg_oper’:
drivers/net/wireless/rtlwifi/base.c:921:23: warning: variable ‘tid_data’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/efuse.o
drivers/net/wireless/rtlwifi/efuse.c: In function ‘efuse_pg_packet_write’:
drivers/net/wireless/rtlwifi/efuse.c:928:24: warning: variable ‘dataempty’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/efuse.c: In function ‘efuse_get_current_size’:
drivers/net/wireless/rtlwifi/efuse.c:1179:5: warning: variable ‘hoffset’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/ps.o
drivers/net/wireless/rtlwifi/ps.c: In function ‘rtl_ps_set_rf_state’:
drivers/net/wireless/rtlwifi/ps.c:85:19: warning: variable ‘rtstate’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/regd.o
drivers/net/wireless/rtlwifi/regd.c: In function ‘_rtl_dump_channel_map’:
drivers/net/wireless/rtlwifi/regd.c:310:28: warning: variable ‘ch’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/rtlwifi/usb.o
drivers/net/wireless/rtlwifi/usb.c: In function ‘_rtl_usb_transmit’:
drivers/net/wireless/rtlwifi/usb.c:826:21: warning: variable ‘urb_list’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rtlwifi/usb.c:825:23: warning: variable ‘skb_list’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
gcc 4.6.0 warnings for b43:
CC [M] drivers/net/wireless/b43/lo.o
drivers/net/wireless/b43/lo.c: In function ‘lo_measure_gain_values’:
drivers/net/wireless/b43/lo.c:304:7: warning: variable ‘trsw_rx’ set but not used [-Wunused-but-set-variable]
CC [M] drivers/net/wireless/b43/dma.o
drivers/net/wireless/b43/dma.c: In function ‘free_all_descbuffers’:
drivers/net/wireless/b43/dma.c:760:30: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
drivers/net/wireless/b43/dma.c: In function ‘b43_dma_handle_txstatus’:
drivers/net/wireless/b43/dma.c:1391:30: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure ibss node's bss_changes under BSS_CHANGED_IBSS.
And also start/stop ani timer only if the station join/leave
the group.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier beacon_interval is used to hold interval value and
some flags (ATH9K_BEACON_ENA &ATH9K_BEACON_PERIOD). So to
extract interval ATH9K_BEACON_PERIOD is used. Those flags
were completely removed. So masking beacon_interval is
not required.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO code is SSB specific, we can safely just use "sdev"
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LP-PHY code is SSB specific, add check for bus type.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EDMA based chips (AR9380+) have 8 Tx FIFO slots, which are used to fix the
tx queue start/stop race conditions which have to be worked around for
earlier chips by keeping the last descriptor in the queue. The current code
stores all frames that do not fit onto the 8 FIFO slots in a separate
list. Whenever a FIFO slot is freed up, the next frame (or A-MPDU) from the
pending queue gets moved to that slot.
This process is not only inefficient, but also unnecessary. The code can
be improved visibly by keeping the pending queue fully linked, and moving
the contents of the entire queue to a FIFO slot as it becomes available.
This patch makes the necessary changes for that and also merges some code
that was duplicated for EDMA vs non-EDMA. It changes txq->axq_link to point
to the last descriptor instead of the link pointer, so that
ath9k_hw_set_desc_link can be used, which works on all chips.
With this patch, a small performance increase for non-aggregated traffic
was observed on AR9380 based embedded hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds to mac80211_hwsim the capability to send traffic via
userspace.
Frame exchange between kernel and user spaces is done through generic
netlink communication protocol. A new generic netlink family
MAC80211_HWSIM is proposed, this family contains three basic commands
HWSIM_CMD_REGISTER, which is the command used to register a new
traffic listener, HWSIM_CMD_FRAME, to exchange the frames from kernel
to user and vice-versa, and HWSIM_CMD_TX_INFO_FRAME which returns
from user all the information about retransmissions, rates, rx signal,
and so on.
How it works:
Once the driver is loaded the MAC80211_HWSIM family will be registered.
In the absence of userspace daemon, the driver itselfs implements a
perfect wireless medium as it did in the past. When a daemon sends a
HWSIM_CMD_REGISTER command, the module stores the application PID, and
from this moment all frames will be sent to the registered daemon.
The user space application will be in charge of process/forward all
frames broadcast by any mac80211_hwsim radio. If the user application
is stopped, the kernel module will detect the release of the socket
and it will switch back to in-kernel perfect channel simulation.
The userspace daemon must be waiting for incoming HWSIM_CMD_FRAME
commands sent from kernel, for each HWSIM_CMD_FRAME command the
application will try to broadcast this frame to all mac80211_hwsim
radios, however the application may decide to forward/drop this frame.
In the case of forwarding the frame, a new HWSIM_CMD_FRAME command will
be created, all necessary attributes will be populated and the frame
will be sent back to the kernel.
Also after the frame broadcast phase, a HWSIM_CMD_TX_INFO_FRAME
command will be sent from userspace to kernel, this command contains
all the information regarding the transmission, such as number of
tries, rates, ack signal, etc.
You can find the actual implementation of wireless mediumd daemon
(wmediumd) at:
* Last version tarball: https://github.com/jlopex/cozybit/tarball/master
* Or visiting my github tree: https://github.com/jlopex/cozybit/tree
Signed-off-by: Javier Lopez <jlopex@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that support for these devices has been added we can enable them
by default and remove the Kconfig not on support for these devices to
be non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions are only used by rt2800usb so they don't have to be
in rt2800lib.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lock is only used in the TX path and thus in process context. Therefore
we can use a much lighter spinlock variant.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on an earlier patch submitted by Shiang)
Add support for RT3572/RT3592/RT3592+Bluetooth combo card
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(split off from the earlier RT35xx patch submitted by Shiang)
There's no point in enabling the PA_PE bits for the bands that we are
not active on.
Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
