Otherwise Extreme Lower Power (ELP) wakeup doesn't work properly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3: zoom2/3: make MMC slot work again
Commit 12f8dfb56 accidentally broke MMC on zoom2/3.
The .vmmc1 field of zoom_twldata was deleted. Restoring it
allows the MMC slot to work again
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing htcherald_defconfig did not include mux support, which
prevented USB and other functionality from working out of the box.
This change updates the defconfig to add it in. It also aligns the
defconfig to the -rc8 kernel config.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch corrects the issue introduced with one of my earlier patches:
OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.
Applies on top of my prevoius patch:
OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]
Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig
[1] http://patchwork.kernel.org/patch/57922/
[2] http://patchwork.kernel.org/patch/61952/
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Comment in omap_init_devices asks to keep init calls and their
implementations in alphabetical order, so let it be that way.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable minimum features to boot omap4430 on es1.0 samples. v2 versions
removes the "CONFIG_SYSFS_DEPRECATED_V2" since it's deprecated. Without
this older file system doesn't boot. One need to upgrade the filesystem
if getting stuck in first init function.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The secondary cores wakes up in time so the wait loop is not
necessary anymore.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the public sram base address and available
size on OMAP4430.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pandora board file updates:
- change keycodes of game buttons
it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
the older DSS driver was never functional on l-o or mainline
kernels due to missing panel driver, so remove unneeded
pandora_lcd platform_device. This also removes last OMAP_TAG
from the board file.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Kevin Hilman <kjh@hilman.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that all OMAP boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.
Cc: linux-net@vger.kernel.org
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new style mux data for 34xx. This should also
work with 3630 easily by adding the processor subset
and ball data.
Note that this data is __initdata, and gets optimized
out except for the GPIO pins if CONFIG_OMAP_MUX
is not set.
Also note that this data uses omap3630 naming for
the SDMMC registers instead of 34xx naming with just
MMC.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Most of the dpll api's from dpll.c are reused for OMAP4.
This patch does extend a few api's for OMAP4 support.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific CM1 and CM2 module
register field masks. Auto generated using a python
script (gen_cm_shifts_and_mask.py) developed by Benoit
Cousson, Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific PRM register bit field
shifts and masks. Auto generated using a python script
(gen_prm_shifts_and_mask.py) developed by Benoit Cousson,
Paul Walmsley and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch adds the offsets for new modules in PRM
and CM for OMAP4
These are autogenerated using a python script (gen_prcm44xx_h.py)
developed by Paul Walmsley and Benoit Cousson.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rather than having to do a usecs = nsecs / NSECS_PER_USEC to
track latency in usecs, just track it in nanoseconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
WARN if a clock/hwmod is missing a clockdomain association since
resulting hwmod will not be able to correctly enable/disable clocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
During suspend and resume, when omap_device deactivation and
activation is happening, the timekeeping subsystem has likely already
been suspended. Thus getnstimeofday() will fail and trigger a WARN().
Use read_persistent_clock() instead of getnstimeofday() to avoid this.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The _dev_wakeup_lat_limit field of struct omap_device is u32, so use
UINT_MAX instead of INT_MAX for the default maximum.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Following the model of to_platform_device(), add to_omap_device()
macro so a platform_device pointer can be converted into an
omap_device pointer.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
