drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
We'd like panels to be able to add things to debugfs underneath the
connector's directory. Let's plumb it through. A panel will be able to
put things in a "panel" directory under the connector's
directory. Note that debugfs is not ABI and so it's always possible
that the location that the panel gets for its debugfs could change in
the future.
NOTE: this currently only works if you're using a modern
architecture. Specifically the plumbing relies on _both_
drm_bridge_connector and drm_panel_bridge. If you're not using one or
both of these things then things won't be plumbed through.
As a side effect of this change, drm_bridges can also get callbacks to
put stuff underneath the connector's debugfs directory. At the moment
all bridges in the chain have their debugfs_init() called with the
connector's root directory.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.2.Ib0bd5346135cbb0b63006b69b61d4c8af6484740@changeid
The ti-sn65dsi86 driver shouldn't hand-roll its own bridge
connector. It should use the normal drm_bridge_connector. Let's switch
to do that, removing all of the custom code.
NOTE: this still _doesn't_ implement DRM_BRIDGE_ATTACH_NO_CONNECTOR
support for ti-sn65dsi86 and that would still be a useful thing to do
in the future. It was attempted in the past [1] but put on the back
burner. However, unless we instantly change ti-sn65dsi86 fully from
not supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR at all to _only_
supporting DRM_BRIDGE_ATTACH_NO_CONNECTOR then we'll still need a bit
of time when we support both. This is a better way to support the old
way where the driver hand rolls things itself.
A new notes about the implementation here:
* When using the drm_bridge_connector the connector should be created
after all the bridges, so we change the ordering a bit.
* I'm reasonably certain that we don't need to do anything to "free"
the new drm_bridge_connector. If drm_bridge_connector_init() returns
success then we know drm_connector_init() was called with the
`drm_bridge_connector_funcs`. The `drm_bridge_connector_funcs` has a
.destroy() that does all the cleanup. drm_connector_init() calls
__drm_mode_object_add() with a drm_connector_free() that will call
the .destroy().
* I'm also reasonably certain that I don't need to "undo" the
drm_bridge_attach() if drm_bridge_connector_init() fails. The
"detach" function is private and other similar code doesn't try to
undo the drm_bridge_attach() in error cases. There's also a comment
indicating the lack of balance at the top of drm_bridge_attach().
[1] https://lore.kernel.org/r/20210920225801.227211-4-robdclark@gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204161245.v2.1.I3ab26b7f197cc56c874246a43e57913e9c2c1028@changeid
Support reading edid through aux channel if panel is connected to aux
bus. Extend anx7625_aux_dpcd_trans() to implement aux transfer function:
1. panel is populated in devm_of_dp_aux_populate_ep_devices(), so move
anx7625_parse_dt() after.
2. Use pm runtime autosuspend since aux transfer function is called
multiple times when reading edid.
3. No-op if aux transfer length is 0.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220213103437.3363848-3-hsinyi@chromium.org
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d1 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Fixes: 6c3c719936 ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit]
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It will connect to the mipi dsi host and find the corresponding
mipi dsi host node, but the node registered by the mipi dsi host
has not been loaded yet. of_find_mipi_dsi_host_by_node() returns -EINVAL
which causes the calling driver to fail.
If the anx7625 driver is loaded afterwards the driver requesting
the mipi dsi host will not notice this.
Better approach is to return -EPROBE_DEFER in such case.
Then when the anx7625 driver appears the driver requesting
the mipi dsi host will be probed again.
Signed-off-by: owen <qwt9588@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220117100949.9542-1-qwt9588@gamil.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Move DisplayPort functions into a separate module to reduce the size
of the KMS helpers. Select DRM_DP_HELPER for all users of the code. To
avoid naming conflicts, rename drm_dp_helper.c to drm_dp.c
This change can help to reduce the size of the kernel binary. Some
numbers from a x86-64 test build:
Before:
drm_kms_helper.ko: 447480 bytes
After:
drm_dp_helper.ko: 216632 bytes
drm_kms_helper.ko: 239424 bytes
For early-boot graphics, generic DRM drivers, such as simpledrm,
require DRM KMS helpers to be built into the kernel. Generic helper
functions for DisplayPort take up a significant portion of DRM KMS
helper library. These functions are not used by generic drivers and
can be loaded as a module.
v3:
* fix include statement in DRM selftests
v2:
* move DP helper code into dp/ (Jani)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114114535.29157-4-tzimmermann@suse.de
When DRM_CHIPONE_ICN6211 is selected, and DRM_KMS_HELPER is not selected,
Kbuild gives the following warning:
WARNING: unmet direct dependencies detected for DRM_PANEL_BRIDGE
Depends on [n]: HAS_IOMEM [=y] && DRM_BRIDGE [=y] && DRM_KMS_HELPER [=n]
Selected by [y]:
- DRM_CHIPONE_ICN6211 [=y] && HAS_IOMEM [=y] && DRM [=y] && DRM_BRIDGE [=y] && OF [=y]
This is because DRM_CHIPONE_ICN6211 selects DRM_PANEL_BRIDGE
without depending on or selecting DRM_KMS_HELPER,
despite DRM_PANEL_BRIDGE depending on DRM_KMS_HELPER.
This unmet dependency bug was detected by Kismet,
a static analysis tool for Kconfig.
Fixes: ce517f1894 ("drm: bridge: Add Chipone ICN6211 MIPI-DSI to RGB bridge")
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220117052146.75811-1-julianbraha@gmail.com
Entering suspend while the display attached to this bridge is still on
makes the resume sequence to resume the bridge first, display last:
when this happens, we get a timeout while resuming the bridge, as its
MCU will get stuck due to the display being unpowered.
On the other hand, on mt8173-elm, closing the lid makes the display to
get powered off first, bridge last, so at resume time the sequence is
swapped (compared to the first example) and everything just works
as expected.
Add a stateless device link to the DRM device that this bridge belongs
to, ensuring a correct resume sequence and solving the unability to
correctly resume bridge operation in the first mentioned example.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220105090802.73564-1-angelogioacchino.delregno@collabora.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
When we added the support for the AUX channel in commit 13afcdd727
("drm/bridge: parade-ps8640: Add support for AUX channel") we forgot
to set "drm_dev" to avoid the warning splat at the beginning of
drm_dp_aux_register(). Since everything was working I guess I never
noticed the splat when testing against mainline. In any case, it's
easy to fix. This is basically just like commit 6cba3fe433 ("drm/dp:
Add backpointer to drm_device in drm_dp_aux") but just for the
parade-ps8640.
Fixes: 13afcdd727 ("drm/bridge: parade-ps8640: Add support for AUX channel")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211206162907.1.I1f5d1eba741e4663050ec1b8e39a753f6e42e38b@changeid
