A number of older CMOTech modems are based on Qualcomm
chips. The blacklisted interfaces are QMI/wwan.
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During firmware download the device expects memory addresses in
big-endian byte order. As the wIndex parameter which hold the address is
sent in little-endian byte order regardless of host byte order, we need
to use swab16 rather than cpu_to_be16.
Also make sure to handle the struct ti_i2c_desc size parameter which is
returned in little-endian byte order.
Reported-by: Ludovic Drolez <ldrolez@debian.org>
Tested-by: Ludovic Drolez <ldrolez@debian.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (table_lock){+.+.+.}:
[<c0075f84>] __lock_acquire+0x1694/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c03af3cc>] _raw_spin_lock+0x4c/0x5c
[<c02bbc24>] usb_store_new_id+0x14c/0x1ac
[<bf007eb4>] new_id_store+0x68/0x70 [usbserial]
[<c025f568>] drv_attr_store+0x30/0x3c
[<c01690e0>] sysfs_kf_write+0x5c/0x60
[<c01682c0>] kernfs_fop_write+0xd4/0x194
[<c010881c>] vfs_write+0xbc/0x198
[<c0108e4c>] SyS_write+0x4c/0xa0
[<c000f880>] ret_fast_syscall+0x0/0x48
-> #0 (s_active#4){++++.+}:
[<c03a7a28>] print_circular_bug+0x68/0x2f8
[<c0076218>] __lock_acquire+0x1928/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c0166b70>] __kernfs_remove+0x254/0x310
[<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
[<c0169fb8>] remove_files.isra.1+0x48/0x84
[<c016a2fc>] sysfs_remove_group+0x58/0xac
[<c016a414>] sysfs_remove_groups+0x34/0x44
[<c02623b8>] driver_remove_groups+0x1c/0x20
[<c0260e9c>] bus_remove_driver+0x3c/0xe4
[<c026235c>] driver_unregister+0x38/0x58
[<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial]
[<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial]
[<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial]
[<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra]
[<c009d6cc>] SyS_delete_module+0x184/0x210
[<c000f880>] ret_fast_syscall+0x0/0x48
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(table_lock);
lock(s_active#4);
lock(table_lock);
lock(s_active#4);
*** DEADLOCK ***
1 lock held by modprobe/190:
#0: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
stack backtrace:
CPU: 0 PID: 190 Comm: modprobe Tainted: G W 3.15.0-rc2 #123
[<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24)
[<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28)
[<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8)
[<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4)
[<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154)
[<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310)
[<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94)
[<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84)
[<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac)
[<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44)
[<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20)
[<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4)
[<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58)
[<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial])
[<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial])
[<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial])
[<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra])
[<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210)
[<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 8e493ca176 ("USB: usb_wwan: fix
bulk-urb allocation") by making sure to require both bulk-in and out
endpoints during port probe.
The original option driver (which usb_wwan is based on) was written
under the assumption that either endpoint could be missing, but
evidently this cannot have been tested properly. Specifically, it would
handle opening a device without bulk-in (but would blow up during resume
which was implemented later), but not a missing bulk-out in write()
(although it is handled in some places such as write_room()).
Fortunately (?), the driver also got the test for missing endpoints
wrong so the urbs were in fact always allocated, although they would be
initialised using the wrong endpoint address (0) and any submission of
such an urb would fail.
The commit mentioned above fixed the test for missing endpoints but
thereby exposed the other bugs which would now generate null-pointer
exceptions rather than failed urb submissions.
The regression was introduced in v3.7, but the offending commit was also
marked for stable.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 1ebca9dad5.
This device was erroneously added to the sierra driver even though it's
not a Sierra device and was already handled by the option driver.
Cc: Richard Farina <sidhayn@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing newlines to dev_<level> messages.
Also make some messages less verbose where appropriate.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Add missing braces to conditional branches and one loop in usb-serial
core and generic implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Do not discard buffered data and make sure to try to resubmit the write
urbs on errors.
Currently a recoverable error would lead to more data than necessary
being dropped.
Also upgrade error messages from debug to error log level.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Make sure to try to resubmit the read urb on errors.
Currently a recoverable error would lead to reduced throughput as only
one urb will be used until the port is closed and reopened (or
resumed or unthrottled).
Also upgrade error messages from debug to error log level.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Drivers are allowed to override the default bulk-out buffer size
(endpoint maximum packet size) in order to increase throughput, but it
does not make much sense to allow buffers smaller than the default.
Note that this is already how bulk_in_size is defined.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Remove erroneous call to usb_clear_halt which is blocking and cannot be
used in interrupt context.
This code has possibly never been executed as it would cause an oops if
it was. Simply treat a stalled-endpoint error as any other error
condition.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Hello,
the following patch adds an entry for the PID of a Cressi Leonardo
diving computer interface to kernel 3.13.0.
It is detected as FT232RL.
Works with subsurface.
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding two more IDs to the ftdi_sio usb serial driver.
It now connects Tagsys RFID readers.
There might be more IDs out there for other Tagsys models.
Signed-off-by: Ulrich Hahn <uhahn@eanco.de>
Cc: Johan Hovold <johan@hovold.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device was mentioned in an OpenWRT forum. Seems to have a "standard"
Sierra Wireless ifnumber to function layout:
0: qcdm
2: nmea
3: modem
8: qmi
9: storage
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for ANT USB-m Stick from Dynastream Innovations, by listing
USB pid
[34366.944805] usb 6-1: New USB device found, idVendor=0fcf, idProduct=1009
[34366.944817] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[34366.944824] usb 6-1: Product: ANT USB-m Stick
[34366.944831] usb 6-1: Manufacturer: Dynastream Innovations
Device reported (https://code.google.com/p/antpm/issues/detail?id=5) to
work through:
$ modprobe usbserial vendor=0x0fcf product=0x1009
Signed-off-by: Kristóf Ralovich <kristof.ralovich@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Often, usb drivers need some driver_info to get a device to work. To
have access to driver_info when using new_id, allow to pass a reference
vendor:product tuple from which new_id will inherit driver_info.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.
However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.
This patch reenables this behaviour for all FTDI devices.
Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.
Cc: stable <stable@vger.kernel.org>
Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to the generic TIOCMIWAIT implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the TIOCMIWAIT mask is always honoured.
The CH341 interrupt status has a multiple-status changed flag which
indicates that multiple status changes has occurred since last interrupt
event. Unfortunately, if the final status is the same, there appears to
be no way to determine which signal(s) has changed (an even number of
times).
This means that the multiple-status flag should not be used in
TIOCMIWAIT as it leads to the signal mask argument being ignored (e.g.
TIOCMIWAIT could return if DSR changes twice, even though the user only
cares about carrier changes).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ring-indicator (RI) status-bit definition, which was defined as CTS,
effectively preventing RI-changes from being detected while reporting
false RI status.
This bug predates git.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up line-status handling somewhat.
Get tty-reference only when actually needed.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare constant device-type data as const.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new C_CMSPAR macro for consistency.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a driver which supports the following Moxa USB to serial converters:
* 2 ports : UPort 1250, UPort 1250I
* 4 ports : UPort 1410, UPort 1450, UPort 1450I
* 8 ports : UPort 1610-8, UPort 1650-8
* 16 ports : UPort 1610-16, UPort 1650-16
The UPORT devices don't directly fit the USB serial model. USB serial
assumes a bulk in/out endpoint pair per serial port. Thus a dual port
USB serial device is expected to have two bulk in/out pairs. The Moxa
UPORT only has one pair for data transfer and places a header on each
transfer over the endpoint indicating for which port the transfer
relates to. There is a second endpoint pair for events, such as modem
control lines changing state, setting baud rates etc. Again, a
multiplexing header is used on these endpoints.
Some ports need to have a kfifo explicitly allocated since the
framework does not allocate one if there is no associated endpoints.
The framework will however free it on unload of the module.
All data transfers are made on port0, yet the locks are taken on PortN.
urb->context points to PortN, even though the URB is for port0.
Where possible, code from the generic driver is called. However
mxuport_process_read_urb_data() is mostly a cut/paste of
usb_serial_generic_process_read_urb().
The driver will attempt to load firmware from userspace and compare
the available version and the running version. If the available
version is newer, it will be download into RAM of the device and
started. This is optional and the driver appears to work O.K. with
older firmware in the devices ROM.
This driver is based on the MOXA driver and retains MOXAs copyright.
[jhovold@gmail.com: fix get_fw_version error path and some style issues]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use direct baud-rate encoding rather than divisors for supported baud
rates.
This restores the way baud rates were set prior to commit 8d48fdf689
("USB: PL2303: correctly handle baudrates above 115200") which added
divisor encoding, but also switched to the new encoding method for all
baudrates above 115200.
As noted by Frank Schäfer <fschaefer.oss@googlemail.com>, baud rate 500k
was later errounously added to the supported baud-rate table although
it can only be set using divisors.
Note that the current implementation could easily be extended to support
arbitrary non-standard baud rates using divisors (e.g. by falling back
to divisors when the table lookup fails).
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function for direct baud-rate encoding.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename baud-rate encoding function to match tty naming.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Encode all device-type specifics in a struct rather than testing for
device type and spreading such information throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add quirk for legacy devices (type 0 and 1) rather than testing on
device type throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge types 0 and 1, whose differences are unknown and have always been
treated the same.
Add TYPE_-prefix to both types.
Test for TYPE_01 (rather than !TYPE_HX) for legacy device quirks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement line-status handling for Siemens phones as a quirk rather than
spreading such information all over the driver by matching on vendor and
and product ids.
Note that the SIEMENS_PRODUCT_ID_EF81, which was added after the
line-status handling for the other Siemens phones was fixed, might also
need this quirk.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant get_line_request (the read back settings are never
used).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor and add error handling to line requests.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error handling and clean up vendor read and write functions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use u16 rather than __u16.
Fix multi-line comment style.
Remove some comments.
Remove unnecessary whitespace and add some where appropriate.
Drop DRIVER_DESC define.
Merge and simplify multi-line error message.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus MSR wait-queue wake up from process_read_urb which never
updates the MSR flags.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to generic tiocmiwait rather than rely on a custom implementation
using racy interruptible_sleep_on().
Note that this driver is mostly stubbed out so neither version of
tiocmiwait will actually work until someone implements
f81232_update_line_status().
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus call to wake up delta_msr_wait from process_read_urb where
the MSR status is never updated (only the LSR bits are masked out).
Comment that the wake-up call should made in f81232_update_line_status
when the MSR status changes.
Note that this driver is still mostly stubbed out.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant error messages on allocation failures, which have
already been logged.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant ioctl debugging from subdrivers. The ioctl request code
has already been logged by usb-serial core.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare device-id tables as const where possible.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.
The common case was fixed by commit bf5e5834bf ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark function metrousb_is_unidirectional_mode() in serial/metro-usb.c
because it is not used outside this file.
This eliminates the following warning in serial/metro-usb.c:
drivers/usb/serial/metro-usb.c:57:12: warning: no previous prototype for ‘metrousb_is_unidirectional_mode’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZTE AC2726 EVDO modem drops ppp connection every minute when driven by
zte_ev but works fine when driven by option. Move the support for AC2726
back to option driver.
Signed-off-by: Dmitry Kunilov <dmitry.kunilov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the CS5 setting on the PL2303 USB-to-serial devices. CS5 has a
value of 0 and the CSIZE setting has been skipped altogether by the enclosing
if. Tested on 3.11.6 and the scope shows the correct output after the fix has
been applied.
Tagged to be added to stable, because it fixes a user visible driver bug and is
simple enough to backport easily.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FTDI UARTs support only 7 or 8 data bits. Until now the ftdi_sio driver would
only report this limitation for CS6 to dmesg and fail to reflect this fact to
tcgetattr.
This patch reverts the unsupported CSIZE setting and reports the fact with less
severance to dmesg for both CS5 and CS6.
To test the patch it's sufficient to call
stty -F /dev/ttyUSB0 cs5
which will succeed without the patch and report an error with the patch
applied.
As an additional fix this patch ensures that the control request will always
include a data bit size.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.
Compiles clean, but couldn't test against hardware.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.
Compiles clean, but couldn't test against hardware.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:
tty_release: ttyUSB1: read/write wait queue active!
It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 818f60365a ("USB: serial: add
memory flags to usb_serial_generic_write_start"), which incorrectly used
GFP_KERNEL in write(), which must not not sleep.
Reported-by: Dave Jones <davej@fedoraproject.org>
Tested-by: Dave Jones <davej@fedoraproject.org>
Cc: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in generic write implementation, which could lead to
temporarily degraded throughput.
The current generic write implementation introduced by commit
27c7acf220 ("USB: serial: reimplement generic fifo-based writes") has
always had this bug, although it's fairly hard to trigger and the
consequences are not likely to be noticed.
Specifically, a write() on one CPU while the completion handler is
running on another could result in only one of the two write urbs being
utilised to empty the remainder of the write fifo (unless there is a
second write() that doesn't race during that time).
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xycACgkQMUfUDdst+ymO+gCgxXdQXSU23i9ykc2CKBemdEBH
w6IAoKcokITcdN1IxxkfiMxOEld2hgZm
=3kbb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver update from Greg KH:
"Here's the big USB driver update for 3.13-rc1.
It includes the usual xhci changes, EHCI updates to get the scheduling
of USB transactions working better, and a raft of gadget and musb
updates as well.
All of this has been in linux-next for a while with no reported
issues"
* tag 'usb-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (305 commits)
USB: Maintainers change for usb serial drivers
usb: usbtest: support container id descriptor test
usb: usbtest: support superspeed device capbility descriptor test
usb: usbtest: support usb2 extension descriptor test
usb: chipidea: only get vbus regulator for non-peripheral mode
USB: ehci-atmel: add usb_clk for transition to CCF
usb: cdc-wdm: ignore speed change notifications
USB: cdc-wdm: support back-to-back USB_CDC_NOTIFY_RESPONSE_AVAILABLE notifications
usbatm: Fix dynamic_debug / ratelimited atm_dbg and atm_rldbg macros
printk: pr_debug_ratelimited: check state first to reduce "callbacks suppressed" messages
usb: usbtest: support bos descriptor test for usb 3.0
USB: phy: samsung: Support multiple PHYs of same type
usb: wusbcore: change WA_SEGS_MAX to a legal value
usb: wusbcore: add a quirk for Alereon HWA device isoc behavior
usb: wusbcore: combine multiple isoc frames in a single transfer request.
usb: wusbcore: set the RPIPE wMaxPacketSize value correctly
usb: chipidea: host: more enhancement when ci->hcd is NULL
usb: ohci: remove ep93xx bus glue platform driver
usb: usbtest: fix checkpatch warning as sizeof code style
UWB: clean up attribute use by using ATTRIBUTE_GROUPS()
...
Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.
Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b8bdad6082.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 57ce61aad7.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 75417d9f99.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b9208c721c.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e917ba01d6.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b5c16c6a03.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 61fa8d694b.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c23bda365d.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 73b583af59.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a77a8c23e4.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 034d1527ad.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7d26a78f62.
Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip. This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to return errors from tiocmget rather than rely on
uninitialised stack data.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export usb_serial_generic_write_start which is needed when implementing
a custom resume function while still relying on the generic write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add memory-flags parameter to usb_serial_generic_write_start which is
called from write, resume and completion handler, all with different
allocation requirements.
Note that by using the memory flag to determine when called from the
completion handler, everything will work as before even if the
completion handler is run with interrupts enabled (as suggested).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up some comments, drop excessive comments and fix-up style.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the device id for the Inovia SEW858 device to the option driver.
Reported-by: Pavel Parkhomenko <ra85551@gmail.com>
Tested-by: Pavel Parkhomenko <ra85551@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this change, the USB cable for Freestyle Option and compatible
glucometers will not be detected by the driver.
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"old_rdtodo" and "size" are short type. They are type promoted to int
and the condition is never true.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn> (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: Michal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DCD pin of the serial port can receive a PPS signal. By calling
the port line discipline dcd handle, this patch allow to monitor PPS
through USB serial devices.
However the performance aren't as good as the uart drivers, so
document this point too.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the device receive a DCD status change, forward the signal to the
USB serial system. This way, we can detect, for instance, PPS pulses.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Prolific, several (unauthorized) cheap and less functional
clones of the PL2303HX chip are in circulation. [1]
I've had the chance to test such a cloned device and it turned out that
it doesn't support any baud rates above 115200 baud (original: 6 Mbaud)
It also doesn't support the divisior based baud rate encoding method,
so no continuous baud rate adjustment is possible.
Nevertheless, these devices have been working (unintentionally) with
the driver up to commit 61fa8d694b ("pl2303: also use the divisor based
baud rate encoding method for baud rates < 115200 with HX chips"), and
this commit broke support for them.
Fortunately, it is pretty simple to distinguish between the original
and the cloned HX chips, so I've added a check and an extra chip type
to keep the clones working.
The same check is used by the latest Prolific Windows driver, so it
should be solid.
[1] http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Clean up the DEVICE_ATTR usage in the USB serial drivers, making them
more obvious as to the permissions that the sysfs files should be.
Note: ftdi_sio.c still has a DEVICE_ATTR() used, that will have to wait
until after 3.12-rc1 comes out when DEVICE_ATTR_WO() shows up in Linus's
tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drv_attrs field of struct bus_type is going away soon, drv_groups
should be used instead. This converts the USB serial bus code to use
the correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix endianess bugs in parallel-port code which caused corrupt
control-requests to be issued on big-endian machines.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write_parport_reg_nonblock() function shouldn't sleep because it's
called with spinlocks held.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-serial-simple uses an unknown stringify macro that make
all drivers being named "stringify(vendor)".
This can be a problem when two drivers have the same (wrong) name:
kernel: usbcore: registered new interface driver usb_serial_simple
kernel: usbserial: USB Serial support registered for stringify(vendor)
kernel Error: Driver 'stringify(vendor)' is already registered, aborting...
kernel: usbserial: problem -16 when registering driver stringify(vendor)
kernel: usbserial: USB Serial deregistering driver stringify(vendor)
kernel: usbcore: deregistering interface driver usb_serial_simple
Before the fix:
$ strings drivers/usb/serial/usb-serial-simple.o
usb_serial_simple
stringify(vendor)
After the fix:
$ strings drivers/usb/serial/usb-serial-simple.o
usb_serial_simple
funsoft
flashloader
vivopay
moto_modem
hp4x
suunto
siemens_mpi
This patch makes usb-serial-simple use the correct stringify operator.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure port DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial DMA-buffers are allocated separately from containing
structure to prevent potential memory corruption on non-cache-coherent
systems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to fail properly if the device is not accepted during attach
in order to avoid null-pointer derefs (of missing interface private
data) at disconnect or release.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parallel-port code of the drivers used a stack allocated
control-request buffer for asynchronous (and possibly deferred) control
requests. This not only violates the no-DMA-from-stack requirement but
could also lead to corrupt control requests being submitted.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently knows about 3 different PL2303 chip types:
The two legacy chip types type_0 and type_1 (PL2303H ?) and the HX
type.
The device distinction is currently completely based on the examination
of the USB descriptors.
During the last years, Prolific has introduced further PL2303 chips,
such as the HXD (HX rev. D), TA (which replaced the X/HX chips), SA,
RA, EA and TB variants.
Unfortunately, all these new chips are currently detected as HX chips,
because they are all using the same bMaxPacketSize0 = 0x40 value in the
USB device descriptor.
At this point it is not clear if these chips are really working with
the driver, there are just some positive indicators (like device
manufacturers claiming Linux support for these devices or commit
8d48fdf689 "correctly handle baudrates above 115200" which should only
be necessary for newer devices, ...)
For a complete support of all devices, we need to distinguish between
them, because they differ in several functional aspects, such as the
maximum supported baud rate (HXD, TB, EA: 12Mbps, HX, TA: 6Mbps,
RA: 1Mbps, SA: 115.2kbps), handshaking line support, RS422/485 and
GPIO ports support (currently not supported by the driver).
And there might be further differences that we don't know yet.
This patch improves the chip type detection by evaluating the bcdDevice
value of the device descriptor. The values are taken from the
datasheets and are safe to use because manufacturers can't change them:
3.00: X/HX, TA
4.00: HXD, EA, RA, SA
5.00: TB
The rest of the device descriptors is completely identical, so no
further distinction is possible this way.
Anyway, Prolifics "checkChipVersion.exe"-tool is definitely able to
distinguish for example between the X/HX and the TA chips, so there
must be a possibility to improve the distinction further...
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip type distinction is getting more and more relevant and
complicating, so always print the chip type.
Printing a name string is also much better than just printing an
internal index number.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for two else-if constructs for the type_1 chip
detection in pl2303_startup(), so merge them.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've found some new datasheets which describe some additionally
supported standard baud rates and I've verified them with my HX
(rev. 3A) device. But adding support for individual (chip type
specific) baud rates would add a good amount of extra code (especially
when support for further chips will be added to the driver one day),
which makes no sense as long as we are not using the direct baud rate
encoding method for newer chips.
So for now, just drop a comment about these additionally supported baud
rates.
The second comment is about the baud rate differences between the two
encoding methods. In theory, we could optimize the code a bit by
comparing the resulting baud rates of both methods and selecting the
one which is closer to the requested baud rate. But that seems to be a
bit overkill, because the differences are very small and the device
likely uses the same baud rate generator for both methods so that the
resulting baud rate would be the same.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the divisor based baud rate encoding method has been fixed and
extended, it can also be used for baud rates < 115200 baud with HX
chips.
This makes it possible to adjust the baud rate almost continuously
instead of just beeing able to select between 16 fixed standard values.
Tested with a PL2303HX 04463A (week 46, 2004, rev 3A).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reinhard Max has done some tests with a PL2303HX (rev A) and a logic
analyzer and it seems, that although the PL2303HX is specified for baud
rates from 75 to 6M baud, the full divisor range can be used with the
divisor based baud rate encoding method. This corresponds to baud rates
from 46 to 24M baud.
Baud rates down to 46 baud (max. divisor) have been confirmed to work
even under heavy/permanent load, so remove the lower limit.
Baud rates up to 24M baud should really be tested carefully in "real
life" scenarios before removing the upper limit completely.
Anyway, the Windows driver allows maximum baud rates of 110% of the
specified limit, so for now, increase the upper limit to this value.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0c967e7e "USB: serial: pl2303 works at 500kbps" added 500000
baud to the list of supported standard baud rates.
But the reason why the driver works with this baud rate is, that since
commit 8d48fdf6 "USB: PL2303: correctly handle baudrates above 115200"
a second (divisor based) baud rate encoding method is used for values
above 115200 baud, which is not limited to a fixed set of standard baud
rates.
Remove the 500000 baud value from the list of standard baud rates
again, because this list is only used with the direct baud rate
encoding method and 500000 baud is not supported with this method.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In opposition to the direct baud rate encoding method, the divisor
based method is not limited to a fixed set of standard baud rates.
Hence, there is no need to round to the next nearest standard value.
Reported-by: Mastro Gippo <gipmad@gmail.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the formula in the code description, Reinhard Max and me have
investigated the devices behavior / functional principle of the divisor
based baud rate encoding method.
It turned out, that (although beeing a good starting point) the current
code has some flaws. It doesn't work correctly for a wide range of baud
rates and the divisor resolution can be improved. It also doesn't
report the actually set baud rate.
This patch fixes and improves the code for the divisor based baud rate
encoding method a lot. It can now be used for the whole range of baud
rates from 46 baud to 24M baud with a very good divisor resolution and
userspace can read back the resulting baud rate.
It also documents the formula used for encoding and the hardware
behavior (including special cases).
The basic algorithm, rounding and several code comments/explanations
are provided by Reinhard Max.
I've added some minor fixes, the handling of the special cases and
further code/algorithm descriptions.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Reinhard Max <max@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix endianess bugs in firmware handling introduced by commits cb7a7c6a
("ti_usb_3410_5052: add Multi-Tech modem support") and 05a3d905
("ti_usb_3410_5052: support alternate firmware") which made the driver
use the wrong firmware for certain devices on big-endian machines.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix bug in device-type detection on big-endian machines originally
introduced by commit 0eafe4de ("USB: serial: mos7840: add support for
MCS7810 devices") which always matched on little-endian product ids.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the bulk-in urb used for incoming data transfer
is not resubmitted if the packet recieved contains an error status. This
results in the driver locking until the port is closed and re-opened.
Tested on a custom board with a Cinterion GSM module.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having to create a new driver for a "simple" usb to serial
device, mush them all into one file, with a macro, so as to make it easy
to add new ones.
Cc: "René Bürgel" <rene.buergel@sohard.de>
Acked-by: Wei Shuai <cpuwolf@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Acked-by: Frans Klaver <frans.klaver@xsens.com>
Cc: "Wesley W. Terpstra" <w.terpstra@gsi.de>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not clear if the type_0 and type_1 chips support the divisor based baud
rate encoding method, so don't use it until anyone with such chip has tested it
to avoid regressions with the following patches.
Even if it has been working fine with these chips since the code has been added
2 years ago, this change will not cause any regressions, because the baud rates
currently supported/allowed with the divisor based method are supported with
the direct method, too.
The code for the divisor based method also isn't entirely correct (yet), so that the
direct encoding method actually works better (sets the baud rate more precisely).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RT Systems makes many usb serial cables based on the ftdi_sio driver for
programming various amateur radios. This patch is a full listing of
their current product offerings and should allow these cables to all
be recognized.
Signed-off-by: Rick Farina (Zero_Chaos) <zerochaos@gentoo.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following regression that has been introduced recently with
commit b2d6d98fc7:
With type_0 and type_1 chips
- all baud rates < 1228800 baud are rounded up to 1228800 baud
- the device silently runs at 9600 baud for all baud rates > 1228800
baud
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silence compiler warnings on 64-bit systems introduced by commit
05cf0dec ("USB: mos7840: fix race in led handling") which uses the
usb-serial data pointer to temporarily store the device type during
probe but failed to add the required casts.
[gregkh - change uintptr_t to unsigned long]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in LED handling introduced by commit 0eafe4de ("USB: serial:
mos7840: add support for MCS7810 devices") which reused the port control
urb for manipulating the LED without making sure that the urb is not
already in use. This could lead to the control urb being manipulated
while in flight.
Fix by adding a dedicated LED urb and ctrlrequest along with a LED-busy
flag to handle concurrency.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in device-type detection introduced by commit 0eafe4de ("USB:
serial: mos7840: add support for MCS7810 devices") which used a static
variable to hold the device type.
Move type detection to probe and use serial data to store the device
type.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix race in mos7840_get_reg which unconditionally manipulated the
control urb (which may already be in use) by adding a control-urb busy
flag.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a driver for the Suunto ANT+ USB device, exposing it as a usb
serial device. This lets the userspace "gant" program to talk to the
device to communicate over the ANT+ protocol to any devices it finds.
Reported-by: Steinar Gunderson <sgunderson@bigfoot.com>
Tested-by: Steinar Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocated urbs and buffers were never freed on errors in open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver failed to take the dynamic ids into account when determining
the device type and therefore all devices were detected as 2-port
devices when using the dynamic-id interface.
Match on the usb-serial-driver field instead of doing redundant id-table
searches.
Reported-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to five new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 0451 1234 >/sys/bus/usb-serial/drivers/ti_usb_3410_5052_1/new_id
for 1-port adapters, or
echo 0451 1234 >/sys/bus/usb-serial/drivers/ti_usb_3410_5052_2/new_id
for 2-port adapters.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write wait queue is never added to since commit f1175daa5 ("USB:
ti_usb_3410_5052: kill custom closing_wait"). Remove it completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill private write fifo and use the already allocated port write fifo
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to a single new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 04dd 1234 >/sys/bus/usb-serial/drivers/safe_serial/new_id
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken "chase" implementation which was supposed to be used to
drain the write buffers at break.
The chase implementation slept on a wait queue which was never woken up
(i.e. no hardware buffers were queried), and thus amounted to nothing
more than polling chars_in_buffer, something which has already been
taken care of by the tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move port initialisation code from open to probe where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill private write fifo and use the already allocated port write fifo
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the vendor and product module parameters which were added a long
time ago when we did not have the dynamic sysfs interface to add
new device ids (and which isn't limited to a single new vid/pid pair).
A vid/pid pair can be added dynamically using sysfs, for example:
echo 0403 1234 >/sys/bus/usb-serial/drivers/ftdi_sio/new_id
Also fix up the in-code comment that got the sysfs path wrong.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not raise DTR/RTS a second time in set_termios at open -- this has
already been taken care of by the tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use zeroed termios data to determine when to unconditionally
configure the device at open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure set_termios is not called with uninitialised data at open. The
old termios struct is currently not used, but pass NULL instead to avoid
future problems (e.g. stack data leak).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only log the tty_flags in process_read_urb on errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out baud-rate handling from set_termios.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary tests for open and write operations as these are set
to the generic implementations by usb-serial core if left unset by a
subdriver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port drain delay is constant and should be set at port probe rather
than open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 957dacae ("TTY: fix DTR not being dropped on hang up")
dtr_rts is no longer called for uninitialised ports (e.g. after
a disconnect), which removes the need to grab the disconnect mutex.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31ca020b ("TTY: wake up processes last at hangup") there no
longer any need to check the hupping flag in the generic tiocmiwait
implementation, so remove it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove defensive test from set_termios which is never called with a NULL
tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for MMB Networks and Planet Innovation Ingeni ZigBee USB
devices using customized Silicon Labs' CP210x.c USB to UART bridge
drivers with PIDs: 88A4, 88A5.
Signed-off-by: Sami Rahman <sami.rahman@mmbresearch.com>
Tested-by: Sami Rahman <sami.rahman@mmbresearch.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: Barry Grussling <barry@grussling.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds NetGear Managed Switch M4100 series, M5300 series, M7100 series
USB ID (0846:0110) to the cp210x driver. Without this, the serial
adapter is not recognized in Linux. Description was obtained from
an Netgear Eng.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option. Their
network port is handled by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add product id for Abbott strip port cable for Precision meter which
uses the TI 3410 chip.
Signed-off-by: Anders Hammarquist <iko@iko.pp.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had the limit of 255 USB to serial devices on one system for almost
15 years, with no complaints. But now it's time to move on from these
tiny "baby" systems, and bump the number up to 512, which should last
us a few more years:
"512 is a nice number" -- Tobias Winter
Note, this is still a static value, and uses up tty core memory with
this many tty devices allocated. Converting the driver to use
TTY_DRIVER_DYNAMIC_DEV is the next thing to do in order to remove this
limitation.
Reported-by: Tobias Winter <tobias@linuxdingsda.de>
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the allocation of minor device numbers from a static array to
be dynamic, using the idr interface. This means that you could
potentially get "gaps" in a minor number range for a single USB serial
device with multiple ports, but all should still work properly.
We remove the 'minor' field from the usb_serial structure, as it no
longer makes any sense for it (use the field in the usb_serial_port
structure if you really want to know this number), and take the fact
that we were overloading a number in this field to determine if we had
initialized the minor numbers or not, and just use a flag variable
instead.
Note, we still have the limitation of 255 USB to serial devices in the
system, as that is all we are registering with the TTY layer at this
point in time.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_serial_port structure had the number field, which was the minor
number for the port, which almost no one really cared about. They
really wanted the number of the port within the device, which you had to
subtract from the minor of the parent usb_serial_device structure. To
clean this up, provide the real minor number of the port, and the number
of the port within the serial device separately, as these numbers might
not be related in the future.
Bonus is that this cleans up a lot of logic in the drivers, and saves
lines overall.
Tested-by: Tobias Winter <tobias@linuxdingsda.de>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
drivers/staging/serqt_usb2/serqt_usb2.c | 21 +++--------
drivers/usb/serial/ark3116.c | 2 -
drivers/usb/serial/bus.c | 6 +--
drivers/usb/serial/console.c | 2 -
drivers/usb/serial/cp210x.c | 2 -
drivers/usb/serial/cypress_m8.c | 4 +-
drivers/usb/serial/digi_acceleport.c | 6 ---
drivers/usb/serial/f81232.c | 5 +-
drivers/usb/serial/garmin_gps.c | 6 +--
drivers/usb/serial/io_edgeport.c | 58 ++++++++++++--------------------
drivers/usb/serial/io_ti.c | 21 ++++-------
drivers/usb/serial/keyspan.c | 29 +++++++---------
drivers/usb/serial/metro-usb.c | 4 +-
drivers/usb/serial/mos7720.c | 37 +++++++++-----------
drivers/usb/serial/mos7840.c | 52 +++++++++-------------------
drivers/usb/serial/opticon.c | 2 -
drivers/usb/serial/pl2303.c | 2 -
drivers/usb/serial/quatech2.c | 7 +--
drivers/usb/serial/sierra.c | 2 -
drivers/usb/serial/ti_usb_3410_5052.c | 10 ++---
drivers/usb/serial/usb-serial.c | 7 ++-
drivers/usb/serial/usb_wwan.c | 2 -
drivers/usb/serial/whiteheat.c | 20 +++++------
include/linux/usb/serial.h | 6 ++-
24 files changed, 133 insertions(+), 180 deletions(-)
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace in the OOM error
path.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
This also prevents stack data from leaking to userspace.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 143d9d9616 ("USB: serial: add
tiocmiwait subdriver operation") which made the ioctl operation return
ENODEV rather than ENOIOCTLCMD when a subdriver TIOCMIWAIT
implementation is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register access to enable hardware flow control depends on the
device port number and not the port minor number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the no longer used endpoint-array access completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The outcont_endpoints array was indexed using the port minor number
(which can be greater than the array size) rather than the device port
number.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus port-number check in open and close, which prevented this
driver from being used with a minor number different from zero.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you want to download Infineon modem via USB, this Infineon USB
flashloader driver is required.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Option GTM681W uses a qualcomm chip and can be
served by the qcserial device driver.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adds a new HIDCOM device and does not affect other devices
driven by the cypress_M8 module. Changes are:
- add VendorID ProductID to device tables
- skip unstable speed check because FRWD uses 115200bps
- skip reset at probe which is an issue workaround for this
particular device.
Signed-off-by: Robert Butora <robert.butora.fi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a specifier we may use to dump small buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control and bulk-message timeouts are specified in milliseconds and
should not depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bulk-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The control-message timeout is specified in milliseconds and should not
depend on HZ.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit 0eafe4de1a ("USB: serial: mos7840:
add support for MCS7810 devices") which used stack-allocated buffers for
control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read_mos_reg function is called with stack-allocated buffers, which
must not be used for control messages.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first and second interrupt-in urbs are swapped for some Treo/Kyocera
devices, but the urb context was never updated with the new port.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rebranded Novatel E371 for AT&T's LTE bands.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'qt2_process_read_urb' is referenced only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to grab disconnect mutex in chars_in_buffer now that no
sub-driver is or should be querying hardware buffers anymore. (They
should use wait_until_sent.)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 2c992cd73 ("USB:
ti_usb_3410_5052: query hardware-buffer status in chars_in_buffer")
without breaking tty_wait_until_sent (used by, for example, tcdrain,
tcsendbreak and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 263e1f9f ("USB:
io_ti: query hardware-buffer status in chars_in_buffer") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new generic usb-serial wait_until_sent implementation to wait
for hardware buffers to drain.
This removes the need to check the hardware buffers in chars_in_buffer
and thus removes the overhead introduced by commit 6f602912 ("usb:
serial: ftdi_sio: Add missing chars_in_buffer function") without
breaking tty_wait_until_sent (used by, for example, tcdrain, tcsendbreak
and close).
Reported-by: Stas Sergeev <stsp@list.ru>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb-serial port rather than tty as argument to get_modem_status.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic wait_until_sent implementation which polls for empty
hardware buffers using the new port-operation tx_empty.
The generic implementation will be used for all sub-drivers that
implement tx_empty but does not define wait_until_sent.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add wait_until_sent operation which can be used to wait for hardware
buffers to drain.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea fixes,
which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+md4ACgkQMUfUDdst+ymkSgCfZWIiCtiX/li0yJqSiRB4yYJx
Ex0AoNemOOf6ywvSOHPbILTbJ1G+c/PX
=JmvB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea
fixes, which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while"
* tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits)
USB: ehci-msm: USB_MSM_OTG needs USB_PHY
USB: OHCI: avoid conflicting platform drivers
USB: OMAP: ISP1301 needs USB_PHY
USB: lpc32xx: ISP1301 needs USB_PHY
USB: ftdi_sio: enable two UART ports on ST Microconnect Lite
usb: phy: tegra: don't call into tegra-ehci directly
usb: phy: phy core cannot yet be a module
USB: Fix initconst in ehci driver
usb-storage: CY7C68300A chips do not support Cypress ATACB
USB: serial: option: Added support Olivetti Olicard 145
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
ARM: mxs_defconfig: add CONFIG_USB_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
usb: phy: remove exported function from __init section
usb: gadget: zero: put function instances on unbind
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
usb: gadget: cdc2: fix error return code in cdc_do_config()
usb: gadget: multi: fix error return code in rndis_do_config()
usb: gadget: f_obex: fix error return code in obex_bind()
USB: storage: convert to use module_usb_driver()
...
The FT4232H used in the ST Micro Connect Lite has four hi-speed UART ports.
The first two ports are reserved for the JTAG interface.
We enable by default ports 2 and 3 as UARTs (where port 2 is a
conventional RS-232 UART)
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.
For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Signed-off-by: Adrian Thomasset <adrian.thomasset@st.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill custom closing_wait implementation and let the tty-layer handle it
instead.
Note that the port drain-delay is set to three characters to keep the
20ms delay after wait_until_sent at low baudrates (1200 baud) during close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant drain, which has already been handled by the tty-layer,
from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Query hardware-buffer status in chars_in_buffer should the write fifo be
empty.
This is needed to make the tty layer wait for hardware buffers to drain
on close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The line status register is only polled so let's not keep a possibly
outdated value in the port data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move write-fifo flushing from ti_drain to close where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant wait_until_sent, which has already been handled by the
tty-layer, from break_ctl.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression introduced by commit f40d78155 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org> # 3.9
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate port-private data in port-probe rather than in attach.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port device for debug messages in interrupt-urb callback and remove
unused private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port interrupt-in urb rather managing a private one.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device uses the second interrupt-in endpoint of the interface for
reading. Stop abusing the port read urb and store a pointer to the
second interrupt-in urb as port-private data instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port interrupt-out urb rather than abusing the port write_urb
pointer and allocating a new urb at every open (but the first...).
Note that the write_urb abuse would have led to a double free should
there ever be interfaces with a bulk-out endpoint.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the more efficient generic read implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor read-urb processing, and add sanity checks on header and data
lengths.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant data-offset define, which was really just the header
length.
Add payload-size define and use the bulk-out size define for the actual
bulk-out size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up and fix typos in protocol comment.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the port private data, which contains the write sequence
number, is cleared at allocation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a sparse warning where we should be using NULL instead of 0
Cc: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol <http://www.ohwr.org/projects/etherbone-core>.
This driver is intended to be used with devices which attach
their internal Wishbone bus to a USB serial interface using
the Etherbone protocol. A userspace library is required to
speak the protocol made available by this driver as ttyUSBx.
Signed-off-by: Wesley W. Terpstra <w.terpstra@gsi.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add a missing usb device id for the GDMBoost V1.x device
The patch is against 3.9-rc5
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_tty_get might return a tty which is NULL. But it is
dereferenced unconditionally in edge_send. Stop dereferencing that by
sending usb_serial_port pointer around.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"len" comes from the USB transfer and it's probably correct. The thing
is that we already have similar checks like:
if (data[i] >= serial->num_ports) {
So adding a sanity test here matches the rest of the code and is a good
idea.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can remove the "if (urb->actual_length) {" check because checking for
"while (i < urb->actual_length) {" is sufficient. This lets us pull the
code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit eba0e3c3a0.
When merged together (usb-linus and usb-next), this fix isn't needed and
causes a build error. Revert the commit to solve the build issue.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW
Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan's 'fix use-after-free in TIOCMIWAIT' patchset[1] introduces
one bug which can cause kernel hang when opening port.
This patch initialized the 'port->delta_msr_wait' waitqueue head
to fix the bug which is introduced in 3.9-rc4.
[1], http://marc.info/?l=linux-usb&m=136368139627876&w=2
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in close. This
can never happen as close is guaranteed to be called before the last tty
reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in read bulk
callback. This can never happen as the port read urb is killed (and
poisoned) at close, which in turn is guaranteed to be called before the
last tty reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test for serial device being NULL in close. This
can never happen as close is guaranteed to be called before the last tty
reference is dropped (and port->serial is cleared).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary disconnect test in tiocmset. No ioctls will be made
after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we return 0 or a negative error number appropriate for
userspace on errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary disconnect test in tiocmset. No ioctls will be made
after disconnect returns.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we return 0 or a negative error number appropriate for
userspace on errors.
Currently 1 rather than 0 is returned on successful operation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove disconnected test from close which did not protect any device IO
at all.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Always try to disable the uart on close.
Since the switch to tty ports, close will be called as part of shutdown
before disconnect returns. Hence there is no need to check the
disconnected flag, and we can put devices in disabled states also on
driver unbind.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetch modem status on carrier_raised and tiocmget.
This driver appeared to support modem-status but only read the modem
status registers once at open and then used that cached value for all
further enquires.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reimplement device type detection using the device id table and quirks.
Device type was used to detect one device type which did not support to
control functions. Add quirks to the device table and store them in the
private port data at probe instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass usb-serial port to the control functions for uart status and work
mode.
Use port device for debugging and use dev_err to report errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken uart-error handling.
This driver appears to implement uart-error handling but does not
receive status interrupts or status information with bulk in transfers.
Instead status was retrieved at open and used to flag only the first
bulk in transfer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken TIOCMIWAIT support.
This drivers appears to implement TIOCMIWAIT but has no means of
receiving modem-status interrupts.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out TIOCMIWAIT handling from custom ioctl operation and use
tiocmiwait operation field instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Note that the interrupt counters will no longer be reset at open which
is in accordance with which how the other drivers work.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove SMP memory barriers from icount handling and rely on the barriers
implied by wait_event, sleep and locks, while using the port lock to
guarantee atomicity.
This is a step in moving over to the generic icount implementations.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken get_icount and TIOCMIWAIT support.
The driver has an icount structure but it is never been updated which
makes get_icount rather pointless and causes TIOCMIWAIT to always return
-EIO.
Note that the TIOCMIWAIT implementation has always been broken and would
not work even if icount support was added as it does not wait for the
modem status to change (does not use a work queue at all).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused, private modem-status wait queue from driver. If
TIOCMIWAIT is ever implemented it must not rely on a private wait queue
which may have been released when woken up.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Note that the interrupt counters will no longer be reset at open which
is in accordance with which how the other drivers work.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Note that the interrupt counters will no longer be reset at open which
is in accordance with which how the other drivers work.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Break out TIOCMIWAIT handling from custom ioctl operation and use
tiocmiwait operation field instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused, private modem-status wait queue from driver. If
TIOCMIWAIT is ever implemented it must not rely on a private wait queue
which may have been released when woken up.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port modem-status-change wait queue on which processes are woken
up at hangup and disconnect.
Currently a process waiting on modem-status changes will not be woken on
device disconnect as wake up was only done in dtr_rts which isn't
guaranteed to be called (e.g. if HUPCL is not set).
Also remove the redundant wake-up call from dtr_rts.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
This also fixes the issue with processes waiting for
modem-status-changes not being woken up at disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic get_icount implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port-data icount for interrupt counters.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic get_icount implementation that subdrivers relying on the
port interrupt counters can use.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure processes waiting for modem-status changes are woken up at
disconnect.
This is needed for custom subdriver TIOCMIWAIT-implementations which do
not yet handle hangup.
Even though processes on the tty-port wait queue are woken up at hangup
the wake-up call in usb-serial disconnect is still needed if a woken-up
process may go back to sleep (e.g. due to an incomplete
TIOCMIWAIT-implementation). If a disconnect occurs after a hangup, any
process waiting for changes will not be woken up a second time by the
tty-layer as the port will then have been disassociated from the tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic TIOCMIWAIT implementation which correctly handles hangup,
USB-device disconnect, does not rely on the deprecated sleep_on
functions and hence does not suffer from the races currently affecting
several usb-serial drivers.
This makes it much easier to add TIOCMIWAIT support to subdrivers as the
tricky details related to hangup and disconnect (e.g. atomicity, that
the private port data may have been freed when woken up, and waking up
processes at disconnect) have been handled once and for all.
To add support to a subdriver, simply set the tiocmiwait-port-operation
field, update the port icount fields and wake up any process sleeping on
the tty-port modem-status-change wait queue on changes.
Note that the tty-port initialised flag can be used to detect
disconnected as the port will be hung up as part of disconnect (and
cannot be reactivated due to the disconnected flag). However, as the
tty-port implementation currently wakes up processes before calling port
shutdown, the tty-hupping flag must also be checked to detect hangup for
now.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to unregister the tty-device before calling subdriver
port_remove.
This way remove will reverse probe, and specifically any port data
released in port_remove will be available throughout tty unregister.
Note that the order currently does not matter as the tty-layer can make
callbacks also after the device has been unregistered. This is
handled in usb-serial core using the disconnected flag, which is
already set when usb-serial bus device remove is called.
Cc: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_poison_urb to reliably kill all urbs on disconnect and suspend.
This way there will be no question that the urbs cannot be resubmitted
by buggy subdrivers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename port_release so that all usb_serial_port functions have a common
prefix.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not call kill_traffic (and usb_kill_urb) once disconnect
returns. Any pending urbs are killed at disconnect and new submissions
are prevented by usb_unbind_interface (and usb_disable_interface).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the interrupt urb submitted in port_probe is killed in
port_remove.
The interrupt-urb completion handler references the port and may get
called after port_remove has returned and the port has been
unregistered (although this is currently prevented by usb-serial core as
we are using a non-private urb).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most USB serial drivers are, and should be, using as much of the generic
implementation as possible.
Rename the fixup_generic function to a more descriptive name.
Reword the related debug message in a more neutral tone (and remember to
add the missing newline).
Finally, move the operations initialisation to after the initial sanity
checks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove empty generic release implementation and make the release
callback non-mandatory (like attach, probe and disconnect).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the now empty generic disconnect callback and make the disconnect
callback non-mandatory.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for the generic disconnect callback to stop the read
and write urbs a second time as this has already been taken care of by
close (which is called from hangup as part of disconnect).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic close operation will be used if the close field is left
uninitialised.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The disconnect callback is set to the generic implementation by
usb-serial core if NULL.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in
cleanup.
The device is never cleared, and cleanup is never called after a
completed disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Simplify urb killing, and remove some related debug and dead code while
at it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in
dtr_rts.
The device is never cleared, and disconnect is handled for dtr_rts in
usb-serial core anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Remove some out-commented bogus code while at it.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus (and unnecessary) test for serial->dev being NULL in close.
The device is never cleared, and close is never called after a completed
disconnect anyway.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant port number from debug output (already printed as part
of device name).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failed allocations already get an OOM message and a stack dump.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant port number from debug output (already printed as part
of device name).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant comments and fix some minor coding style issues.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the tty-port callbacks using a common prefix to more clearly
separate them from the tty and usb driver callbacks.
Rename serial_down to serial_port_shutdown to match the callback name.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass usb-serial port rather than usb device to set_control_lines, and
make sure port device is used for all port related debugging.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use interface rather than usb-serial device for debugging interface
related operations. This gives more descriptive messages, such as
[ 905.669436] pl2303 1-4.1:1.0: 0x40:0x1:0x8:0x0 0
rather than
[ 341.943535] usb 1-4.1: 0x40:0x1:0x8:0x0 0
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove kill of interrupt-in urb on close as it has never been submitted.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove kill of interrupt-in urb on close as it has never been submitted.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the port data refcounting and release the private data
explicitly at port remove.
The port data refcounting was used to make sure the port data was not
freed until the last tty reference was closed. Since moving over to tty
ports, the underlying assumptions are no longer valid as close is now
called as part of tty port shutdown, which can occur before the final
tty reference is dropped on device disconnect.
This means that the private port data refcounting is now completely
useless, as the last reference will always be dropped on port_remove.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If suspend callback fails in system sleep context, usb core will
ignore the failure and let system sleep go ahead further, so
this patch comments on the case and requires that serial->type->suspend()
MUST return 0 in system sleep context.
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 27b351c554. It caused
problems with the build.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bill Pemberton <wfp5p@viridian.itc.virginia.edu>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure waiting processes are woken on modem-status changes.
Currently processes are only woken on termios changes regardless of
whether the modem status has changed.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
When switching to tty ports, some lifetime assumptions were changed.
Specifically, close can now be called before the final tty reference is
dropped as part of hangup at device disconnect. Even with the ftdi
private-data refcounting this means that the port private data can be
freed while a process is sleeping on modem-status changes and thus
cannot be relied on to detect disconnects when woken up.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Also remove bogus test for private data pointer being NULL as it is
never assigned in the loop.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the interface is not released before our serial device.
Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing get_icount field to two-port driver.
The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913a ("tty: Convert the USB drivers to the
new icount interface").
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.
The possible IO it was supposed to prevent is long gone.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 27b351c554.
Calling tty_flip_buffer_push on an unopened tty is legal, so the
driver doesn't need track if port has been opened. Reverting this
allows the entire is_open logic to be removed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the fixes in that branch, and let Alan fix the merge
error in drivers/usb/host/ehci-timer.c better than I just did (as I know
I messed it up...)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->ops->break_ctl cannot be called outside the gap between open and
close. So there is no need to check whether the port is open in
break_ctl in quatech2. Remove the check and also that member
completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It allows for cleaning up on a considerable amount of places. They did
port_get, wakeup, kref_put. Now the only thing needed is to call
tty_port_tty_wakeup which does exactly that.
One exception is ifx6x60 where tty_wakeup was open-coded. We now call
tty_wakeup properly there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty port ops shutdown() routine is not called for console ports;
remove extra check.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 2e124b4a39 removed the checks
that prevented qt2_process_read_urb() from trying to put chars into
ttys that weren't actually opened. This resulted in 'tty is NULL'
warnings from flush_to_ldisc() when the device was used.
The devices use just one read urb for all ports. As a result
qt2_process_read_urb() may be called with the current port set to a
port number that has not been opened. Add a check if the port is open
before calling tty_flip_buffer_push().
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turns out we just need altsetting 1 and then we can talk to it.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Rigblaster Advantage is an amateur radio interface sold by West Mountain
Radio. It contains a cp210x serial interface but the device ID is not in
the driver.
Signed-off-by: Steve Conklin <sconklin@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
4 ports; AT/PPP is standard CDC-ACM. The other three (added by this
patch) are QCDM/DIAG, possibly GPS, and unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the Lake Shore Cryotronics devices to
the CP210x driver.
These lines are ported from cp210x driver distributed by Lake Shore web site:
http://www.lakeshore.com/Documents/Lake%20Shore%20cp210x-3.0.0.tar.gz
and licensed under the terms of GPLv2.
Moreover, I've tested this changes with Lake Shore 335 in my labs.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add support for Cinterion's products AH6 and PLS8 by adding Product IDs
and USB_DEVICE tuples.
Signed-off-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another device using CDC ACM with vendor specific protocol to mark
serial functions.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.
The CDC ACM class driver cannot support functions with only 2
endpoints. The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.
There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure serial-driver dtr_rts is called with disc_mutex held after
checking the disconnected flag.
Due to a bug in the tty layer, dtr_rts may get called after a device has
been disconnected and the tty-device unregistered. Some drivers have had
individual checks for disconnect to make sure the disconnected interface
was not accessed, but this should really be handled in usb-serial core
(at least until the long-standing tty-bug has been fixed).
Note that the problem has been made more acute with commit 0998d06310
("device-core: Ensure drvdata = NULL when no driver is bound") as the
port data is now also NULL when dtr_rts is called resulting in further
oopses.
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PID/VID entries for ELV WS 300 PC II weather station
Signed-off-by: Sven Killig <sven@killig.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for the OWL CM-160 electricity monitor to the cp210x
driver.
Signed-off-by: Luis Llorente <luisllorente@luisllorente.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding three currently unsupported modems based on information
from .inf driver files:
Diag VID_1BBB&PID_0052&MI_00
AGPS VID_1BBB&PID_0052&MI_01
VOICE VID_1BBB&PID_0052&MI_02
AT VID_1BBB&PID_0052&MI_03
Modem VID_1BBB&PID_0052&MI_05
wwan VID_1BBB&PID_0052&MI_06
Diag VID_1BBB&PID_00B6&MI_00
AT VID_1BBB&PID_00B6&MI_01
Modem VID_1BBB&PID_00B6&MI_02
wwan VID_1BBB&PID_00B6&MI_03
Diag VID_1BBB&PID_00B7&MI_00
AGPS VID_1BBB&PID_00B7&MI_01
VOICE VID_1BBB&PID_00B7&MI_02
AT VID_1BBB&PID_00B7&MI_03
Modem VID_1BBB&PID_00B7&MI_04
wwan VID_1BBB&PID_00B7&MI_05
Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on
wwan VID_1BBB&PID_0000&MI_04
wwan VID_1BBB&PID_0017&MI_06
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill custom closing_wait implementation and let the tty layer handle it
instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Query hardware-buffer status in chars_in_buffer should the write fifo be
empty.
This is needed to make the tty layer wait for hardware buffers to drain
on close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grab disconnect mutex in chars_in_buffer before checking disconnected
flag or calling driver specific function.
This allows subdrivers to query any hardware buffer status without
having to handle the locking themselves.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use tty-port drain delay rather than custom implementation in
chase_port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move write-fifo flushing from chase_port to close where it belongs.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diagnostics VID_2357&PID_0201&MI_00
NMEA VID_2357&PID_0201&MI_01
Modem VID_2357&PID_0201&MI_03
Networkcard VID_2357&PID_0201&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diag VID_19D2&PID_0265&MI_00
NMEA VID_19D2&PID_0265&MI_01
AT cmd VID_19D2&PID_0265&MI_02
Modem VID_19D2&PID_0265&MI_03
Net VID_19D2&PID_0265&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Now 4 string flipping ones are on turn:
* tty_insert_flip_string_flags
* tty_insert_flip_string_fixed_flag
* tty_prepare_flip_string
* tty_prepare_flip_string_flags
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Here we start with tty_buffer_request_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.
Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Signed-off-by: Tomasz Mloduchowski <q@qdot.me>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
also known as Alcatel One Touch L100V LTE
The driver description files gives these names to the vendor specific
functions on this modem:
Application1: VID_1BBB&PID_011E&MI_00
Application2: VID_1BBB&PID_011E&MI_01
Modem: VID_1BBB&PID_011E&MI_03
Ethernet: VID_1BBB&PID_011E&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In option.c, add some new MEDIATEK PIDs support for MEDIATEK new products. This
is a MEDIATEK inc. release patch.
Signed-off-by: Quentin.Li <snowmanli88@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers to
all work together nicer, which was a reduction in overall code. We also
deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a nice
thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhIYACgkQMUfUDdst+yk9gACgsZYgMtbrqdbhbjbYkfO7nYkB
iegAoIvj3qwe33TbZ8OJnIkaWcMiT8CW
=u6Bf
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big set of USB patches for 3.8-rc1.
Lots of USB host driver cleanups in here, and a bit of a reorg of the
EHCI driver to make it easier for the different EHCI platform drivers
to all work together nicer, which was a reduction in overall code. We
also deleted some unused firmware files, and got rid of the very old
file_storage usb gadget driver that had been broken for a long time.
This means we ended up removing way more code than added, always a
nice thing to see:
310 files changed, 3028 insertions(+), 10754 deletions(-)
Other than that, the usual set of new device ids, driver fixes, gadget
driver and controller updates and the like.
All of these have been in the linux-next tree for a number of weeks.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (228 commits)
USB: mark uas driver as BROKEN
xhci: Add Lynx Point LP to list of Intel switchable hosts
uwb: fix uwb_dev_unlock() missed at an error path in uwb_rc_cmd_async()
USB: ftdi_sio: Add support for Newport AGILIS motor drivers
MAINTAINERS: remove drivers/block/ub.c
USB: chipidea: fix use after free bug
ezusb: add dependency to USB
usb: ftdi_sio: fixup BeagleBone A5+ quirk
USB: cp210x: add Virtenio Preon32 device id
usb: storage: remove redundant memset() in usb_probe_stor1()
USB: option: blacklist network interface on Huawei E173
USB: OHCI: workaround for hardware bug: retired TDs not added to the Done Queue
USB: add new zte 3g-dongle's pid to option.c
USB: opticon: switch to generic read implementation
USB: opticon: refactor reab-urb processing
USB: opticon: use usb-serial bulk-in urb
USB: opticon: increase bulk-in size
USB: opticon: use port as urb context
USB: opticon: pass port to get_serial_info
USB: opticon: make private data port specific
...
The Newport AGILIS model AG-UC8 compact piezo motor controller
(http://search.newport.com/?q=*&x2=sku&q2=AG-UC8)
is yet another device using an FTDI USB-to-serial chip. It works
fine with the ftdi_sio driver when adding
options ftdi-sio product=0x3000 vendor=0x104d
to modprobe.d. udevadm reports "Newport" as the manufacturer,
and "Agilis" as the product name.
Signed-off-by: Martin Teichmann <lkb.teichmann@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BeagleBone A5+ devices ended up getting shipped with the
'BeagleBone/XDS100V2' product string, and not XDS100 like it
was agreed, so adjust the quirk to match.
For details, see the thread on the beagle list:
https://groups.google.com/forum/#!msg/beagleboard/zrFPew9_Wvo/ibWr1-eE8JwJ
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Huawei E173 will normally appear as 12d1:1436 in Linux. But
the modem has another mode with different device ID and a slightly
different set of descriptors. This is the mode used by Windows like
this:
3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003
All interfaces have the same ff/ff/ff class codes in this mode.
Blacklisting the network interface to allow it to be picked up by
the network driver.
Cc: stable <stable@vger.kernel.org>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to the more efficient generic read implementation.
Note that the generic implementation is not required to hold the tty
port mutex during resume due to the read-urb free mask and write start
flag.
Note also that the generic resume implementation will call generic
write start if there is a bulk-out end-point, but that nothing will be
submitted as the write fifo is not used and is empty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor and clean up read-urb processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the bulk-in urb provided by usb-serial core rather than allocating a
private one.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 256 byte bulk-in buffers rather than double end-point sized ones.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port rather than private data as urb context, as the latter may be
accessed as port data, and remove the port field from the private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass port rather then private data to get_serial_info, which only used
the private data to access the port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make private data port specific and move allocation and deallocation to
port_probe and port_remove.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove disconnect and its redundant read-urb kill which is already taken
care of in close.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move read-urb deallocation from disconnect to release.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove custom end-point iteration which has already been taken care of
by usb-serial core.
The first bulk-in endpoint found will be associated with the first port.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant usb-serial field from private data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove redundant zero-initialisation of outstanding-urbs field in
kzalloced struct.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove usb-serial-device field from private data as it can be accessed
from the usb-serial-port structure.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port rather than interface device to report port related errors and
debug information.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There no need to reinitialise the private urb at every open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The private bulk in urb is set up at open and does not need to be
reinitialised at every resubmit.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f79b2d0f (USB: keyspan: fix NULL-pointer dereferences and
memory leaks) had a small typo which made the driver use wrong
offsets when mapping serial port private data. This results in
in a GPF when the port is opened.
Reported-by: Richard <richjunk@pacbell.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The exception is needed on big endian systems too.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for a vendor specific probe exception just to
match on the interface class.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many modems in addition to the D-Link DWM 652
exposing the CD interface in modem mode, and some expose
an integrated card reader as well. Always ignore these
interfaces.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove all MODULE_VERSION macros and driver-version information (except
for garmin_gps which uses it in a status reply).
It is the kernel version that matters and not some private version
scheme which rarely even gets updated.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use ftdi_get_modem_status to check hardware buffers in chars_in_buffer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to check hardware buffers when we know that the software
buffers are non-empty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use generic chars_in_buffer rather than copying it's implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export generic chars_in_buffer implementation so it can be used in
subdrivers in combination with checks of any hardware buffers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we do not return USB-internal error codes to userspace.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align the modem-control status operands as was originally indented.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unused port field from private port data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure we do not allocate urbs if we do not have a bulk endpoint.
Legacy code used incorrect assumption to test for bulk endpoints.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in all of the USB changes in 3.7-rc3 into usb-next and
resolves the merge issue with:
drivers/usb/misc/ezusb.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove temporary do-while(0) loop used to keep changes minimal.
Fixup indentation, remove some line breaks, and replace break with goto
to maintain flow.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the indentation was kept intact using a do-while(0) in order
to facilitate review. A follow-up patch will remove it.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove private zombie flag used to signal disconnect and to prevent
control urb from being submitted from interrupt urb completion handler.
The control urb will not be re-submitted as both the control urb and the
interrupt urb is killed on disconnect.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The private int_urb is never allocated so the submission from the
control completion handler will always fail. Remove this odd piece of
broken code.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not wait until the hardware buffer (for data from the PC to the
UART line) is drained when tcdrain or close is called in an application.
Solution: Implement a chars_in_buffer function that checks both the software
and hardware buffer. If the TEMT (TX empty) bit of the line status register
indicates the hw buffer is not empty, let the function return at least 1. This
has been verified to work correctly with an FT232RL. The check on the hw buffer
can not be done for the original SIO device.
Signed-off-by: Jarkko Huijts <jarkko.huijts@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Note that the usb device id is stored at probe so that it can be used
in attach to determine send-setup blacklisting.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver set the usb-serial port pointers to NULL on errors in attach,
effectively preventing usb-serial core from decrementing the port ref
counters and releasing the port devices and associated data.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure control urb is freed at release.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note also that urb-count for multi-port interfaces has not been changed
even though the usb-serial port number is now determined from the port
and interface minor numbers.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated on
errors in usb-serial probe.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure port private data is deallocated on errors in attach.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak in usb-serial probe error path by moving port
data allocation to port_probe.
Since commit a1028f0abf ("usb: usb_wwan: replace release and disconnect
with a port_remove hook") port data is deallocated in port_remove. This
leaves a possibility for memory leaks if usb-serial probe fails after
attach but before the port in question has been successfully registered.
Note that this patch also fixes two additional memory leaks in the error
path of attach should port initialisation fail for any port as the urbs
were never freed and neither was the data of any of the successfully
initialised ports.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix NULL-pointer dereference at release by moving port data allocation
and deallocation to port_probe and port_remove.
Fix NULL-pointer dereference at disconnect by stopping port urbs at
port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer accessible at
disconnect or release.
Note that this patch also fixes port and interface-data memory leaks in
the error path of attach should port initialisation fail for any port.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure generic close is called at close.
The driver relies on the generic write implementation but did not call
generic close.
Note that the call to kill the read urb is not redundant, as mct_u232
uses an interrupt urb from the second port as the read urb and that
generic close therefore fails to kill it.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to allocate the control-message buffer dynamically as some
platforms cannot do DMA from stack.
Note that only the first byte of the old buffer was used.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure no control urb is submitted during close after a disconnect by
checking the disconnected flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kill urbs unconditionally at close and disconnect.
Note that URB status is not valid outside of completion handler.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that this also fixes memory leaks in the error path of attach where
the write urbs were not freed on errors.
Make sure all interface-data deallocation is done in release by moving
the read urb deallocation from disconnect.
Note that the write urb is killed during close so that the call in
disconnect was superfluous.
Compile-only tested.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leak in attach error path where the read urb was never freed.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that this patch also fixes a second port-data memory leak in the
error path of attach, should parallel-port initialisation fail.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the oob port is never registered as a port device and should
thus be handled in attach and release.
Compile-only tested.
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation to port_probe
and actually implementing deallocation.
Note that this driver has never even bothered to try to deallocate it's
port data...
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the fifth port (command port) is never registered as a
port device and thus should be handled in attach and release.
Compile-only tested.
Cc: <support@connecttech.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure command buffer is deallocated in case of errors during attach.
Cc: <support@connecttech.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure no control urb is submitted during close after a disconnect by
checking the disconnected flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the call to metrousb_clean (close) in shutdown was redundant.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found a memory leak in sierra_release() (well sierra_probe() I guess)
that looses 8 bytes each time the driver releases a device.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on information from the ZTE Windows drivers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure port data is initialised before creating sysfs attributes to
avoid a race.
A recent patch ("USB: io_ti: fix port-data memory leak") got the
sysfs-attribute creation and port-data initialisation ordering wrong.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure sysfs attributes are created at port probe.
A recent patch ("USB: iuu_phoenix: fix port-data memory leak") removed
the sysfs-attribute creation by mistake.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by moving port data allocation and
deallocation to port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1615) fixes a bug in the Garmin USB serial driver. It
uses attach, disconnect, and release routines to carry out actions
that should be handled by port_probe and port_remove routines, because
they access port-specific data.
The bug causes an oops when the device in unplugged, because the
private data for each port structure now gets erased when the port is
unbound from the driver, resulting in a null-pointer dereference.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported--by: Markus Schauler <mschauler@gmail.com>
Tested-by: Markus Schauler <mschauler@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by allocating and freeing port data in
port_probe/remove rather than in attach/release, and by introducing
serial private data to store the device type which is interface rather
than port specific.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port data memory leak by replacing port private data with serial
private data.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at
release.
The private data is used to store the control interface number, but as
this is the same for all ports on an interface it should be stored as
usb-serial data anyway.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Note that the write waitqueue was initialised but never used.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix NULL-pointer dereference at release by replacing attach and release
with port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is NULL when release is called.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree. There are also the
usual XHCI set of updates, and other various driver changes and updates.
We also are trying hard to remove the old dbg() macro, but the final
bits of that removal will be coming in through the networking tree
before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3+AACgkQMUfUDdst+ym5vwCfe93FyJyXn/RDkGz7iBemvWFd
vrwAoIxjaOa4/yWZWcgrWc5bP4aO3ssc
=jYDr
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB changes from Greg Kroah-Hartman:
"Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree.
There are also the usual XHCI set of updates, and other various driver
changes and updates. We also are trying hard to remove the old dbg()
macro, but the final bits of that removal will be coming in through
the networking tree before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up several annoying - but fairly mindless - conflicts due to the
termios structure having moved into the tty device, and often clashing
with dbg -> dev_dbg conversion.
* tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (339 commits)
USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc
USB: uas: fix gcc warning
USB: uas: fix locking
USB: Fix race condition when removing host controllers
USB: uas: add locking
USB: uas: fix abort
USB: uas: remove aborted field, replace with status bit.
USB: uas: fix task management
USB: uas: keep track of command urbs
xhci: Intel Panther Point BEI quirk.
powerpc/usb: remove checking PHY_CLK_VALID for UTMI PHY
USB: ftdi_sio: add TIAO USB Multi-Protocol Adapter (TUMPA) support
Revert "usb : Add sysfs files to control port power."
USB: serial: remove vizzini driver
usb: host: xhci: Fix Null pointer dereferencing with 71c731a for non-x86 systems
Increase XHCI suspend timeout to 16ms
USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
USB: sierra_ms: don't keep unused variable
fsl/usb: Add support for USB controller version 2.4
USB: qcaux: add Pantech vendor class match
...
This patch
- moves drivers/usb/serial/ezusb.c to drivers/usb/misc/
- renamed CONFIG_USB_EZUSB to CONFIG_USB_EZUSB_FX2 to avoid build errors
- adapts Makefiles and Kconfigs switching from bool to tristate for CONFIG_USB_EZUSB_FX2
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA) is an FTDI FT2232H
based device which provides an easily accessible JTAG, SPI, I2C, serial
breakout.
http://www.diygadget.com/tiao-usb-multi-protocol-adapter-jtag-spi-i2c-serial.htmlhttp://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User%27s_Manual
FTDI FT2232H provides two serial channels (A and B), but on the TUMPA
channel A is dedicated to JTAG/SPI while channel B can be used for
UART/RS-232: use the ftdi_jtag_quirk to expose only channel B as
a usb-serial interface to userspace.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's out-dated for the tty-layer stuff, and would require a bunch of
work. That's not really a big deal, the big issue is that there is no
company contact for the hardware, so questions we have about it (like
why isn't this just handled by the cdc-acm driver instead?) go
unanswered.
So drop the driver. If someone comes along to help answer the
questions, we can easily revert this and fix up the code.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and
P4200 (106c:3721) all use the same subclasses to identify vendor
specific functions. Replace the existing device specific entries
with generic vendor matching, adding support for the P4200.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Cc: Thomas Schäfer <tschaefer@t-online.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I fixed up all of the #ifdef stuff, so remove the comment saying it
still needs to be removed.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Fengguang:
FYI, coccinelle warns about
drivers/usb/serial/usb-serial.c:1415:3-51: code aligned with following code on line 1416
vim +1415 drivers/usb/serial/usb-serial.c
1412 /* we only set the reset_resume field if the serial_driver has one */
1413 for (sd = serial_drivers; *sd; ++sd) {
1414 if ((*sd)->reset_resume)
> 1415 udriver->reset_resume = usb_serial_reset_resume;
> 1416 break;
1417 }
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: stable <stable@vger.kernel.org> [3.5]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new functions to upload firmware to the controller. The
drivers currently using ezusb are adapted to use these new functions.
This also fixes a bug occuring during firmware loading in the
whiteheat-driver:
The driver iterates over an ihex-formatted firmware using ++ on a "const
struct ihex_binrec*" which leads to faulty results, because ihex data is
read as length. The function "ihex_next_binrec(record)" has so be used
to work correctly
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Patch adds support for the newer Cypress FX2LP. It also adapts
three drivers currently using ezusb to the interface change. (whiteheat
and keyspan[_pda])
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves to using pr_info() where needed instead of a "raw" printk()
call, making the whole driver more unified.
It also cleans up my email address in the MODULE_AUTHOR field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver should not be sending any printk() messages when it is
loaded, as no other USB serial driver does. This fixes that, and also
removes the useless version number from the driver.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was calling printk() directly at startup, which is just
noise. Switch over to using pr_info() where needed, and get rid of the
totally useless version number that had never ever been incremented.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should be calling dev_err() instead of printk(KERN_INFO...) so this
change fixes that up properly.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These somehow got missed previously (as they weren't calling dbg(), but
rather printk() directly), so move over to using dev_dbg() as we never
want to see startup messages unless debugging is enabled.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't be telling the syslog that the driver was loaded, the majority of
the usb-serial drivers do not, so this one shouldn't either.
Also remove the pointless driver version information.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() like the rest of that function does, and the rest of the
driver does, to properly show what device and driver caused the problem.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No one needs to know that the driver is loaded (almost all other USB
serial drivers are now quiet), so just load quietly.
Also remove unused, and unneeded version information from the driver,
that was pointless.
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code shouldn't be calling printk(), no one needs to know this debug
message, the return code is good enough.
Cc: "René Bürgel" <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try
to use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I forgot to remove an unused variable.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Wang YanQing <Udknight@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Mark Ferrell <mferrell@uplogix.com>
CC: Donald Lee <donald@asix.com.tw>
CC: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should use dev_dbg() for usb_serial_debug_data() like all of the rest
of the usb-serial drivers use, so remove the debug parameter as it's not
needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a driver for the Vizzini USB to serial device.
It looks to be copied from cdc-acm, and probably can be cleaned up a lot
more. Also, there's some odd "try to grab another interface" that is
probably wrong. And, if this really is a cdc-acm device, it probably
should just be a quirk of the cdc-acm device, but I can't figure that
out, and people have been using this driver for a long time now. So
merge it to let people use their hardware and clean it up over time.
Driver written by Rob Duncan but cleaned up and forward ported to the
latest kernel tree by me.
Cc: Rob Duncan <rob.duncan@exar.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: "Eric W. Biederman" <ebiederm@xmission.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I accidentally caused some compiler warnings, that were correct in
pointing out problems, so fix them up now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the keyspan
driver and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Mark Ferrell <mferrell@uplogix.com>
CC: Donald Lee <donald@asix.com.tw>
CC: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Dan Williams <dcbw@redhat.com>
CC: Thomas Tuttle <ttuttle@chromium.org>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: "Bjørn Mork" <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
CC: Simon Arlott <simon@fire.lp0.eu>
CC: Andrew Worsley <amworsley@gmail.com>
CC: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Peter Berger <pberger@brimson.com>
CC: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Johan Hovold <jhovold@gmail.com>
CC: Preston Fick <preston.fick@silabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
CC: Simon Arlott <simon@fire.lp0.eu>
CC: Andrew Worsley <amworsley@gmail.com>
CC: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Peter Berger <pberger@brimson.com>
CC: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Lonnie Mendez <dignome@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the dependency on the usb_serial interface and names
some magic constants
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
--
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add check for return value of tty_port_tty_get,
since it can return NULL after port hangup that may happen anytime.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: "Bjørn Mork" <bjorn@mork.no>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: "Bjørn Mork" <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Preston Fick <preston.fick@silabs.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cleans up the usb-serial module to remove all old usages of dbg()
and "raw" printk() calls for error reporting (there are some info
messages left for now.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These dbg() calls were no more than just a function trace, so remove
them. If you want to see the functions being called, use the in-kernel
function trace code instead, it's much nicer.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a driver for the zte_ev set of usb to serial devices. It is
based on a patch floating around the internet that modified the generic
usb-serial driver to only work for this type of device.
I've left comments in the code that I think show the data commands being
sent to the device, which I'm guessing come from a usb analyzer. Maybe
they can help others out as well.
Many thanks to nirinA raseliarison for pointing the original patch out
to me, and for testing that the driver works properly.
Tested-by: nirinA raseliarison <nirina.raseliarison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application. This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction. The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.
Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00. I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.
Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory return by kzalloc() or kmem_cache_zalloc() has already
be set to zero, so remove useless memset(0).
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we will be removing items off the list using list_del() we need
to use a safer version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe(). We should use the safe macro if the loop
involves deletions of items.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>. It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b69cc67205 added support for the E-861. After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.
Compiled, but only actually tested on the E-861 and C-867.
Signed-off-by: Éric Piel <piel@delmic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn's latest patchset does break Gobi 1K and 2K because on both
devices as it claims usb interface 0. That's because usbif 0 is not
handled in the switch statement, and thus the if0 gets claimed when it
should not. So let's just make things even simpler yet, and handle both
the 1K and 2K+ cases separately. This patch should not affect the new
Sierra device support, because those devices are matched via
interface-specific matching and thus should never hit the composite
code.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn's latest patchset does break Gobi 1K and 2K because on both
devices as it claims usb interface 0. That's because usbif 0 is not
handled in the switch statement, and thus the if0 gets claimed when it
should not. So let's just make things even simpler yet, and handle both
the 1K and 2K+ cases separately. This patch should not affect the new
Sierra device support, because those devices are matched via
interface-specific matching and thus should never hit the composite
code.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mos7840 driver was using multiple of HZ for the timeout handed off to
usb_control_msg(). Changed the timeout to use msecs instead.
* Remove unused WAIT_FOR_EVER definition
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ZTE (Vodafone) K5006-Z use the following
interface layout:
00 DIAG
01 secondary
02 modem
03 networkcard
04 storage
Ignoring interface #3 which is handled by the qmi_wwan
driver.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the leak of a tty kref that Jiri pointed out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixes these errors:
drivers/usb/serial/console.c: In function 'usb_console_setup':
drivers/usb/serial/console.c:168:16: error: invalid type argument of '->' (have 'struct ktermios')
drivers/usb/serial/console.c:169:4: error: incompatible type for argument 1 of 'tty_termios_encode_baud_rate'
include/linux/tty.h:449:13: note: expected 'struct ktermios *' but argument is of type 'struct ktermios'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointers should not be compared to plain integers.
Quiets the sparse warning:
warning: Using plain integer as NULL pointer
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot unconditionally access any usb-serial port specific
data from the interface driver. Both supending and resuming
may happen after the port has been removed and portdata is
freed.
Treat ports with no portdata as closed ports to avoid a NULL
pointer dereference on resume. No need to kill URBs for
removed ports on suspend, avoiding the same NULL pointer
reference there.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb-serial drivers may access port data in their suspend/
resume functions. Such drivers must always verify the validity
of the data as both suspend and resume can be called both before
usb_serial_device_probe and after usb_serial_device_remove.
But the port data may be invalidated during port_probe and
port_remove. This patch prevents the race against suspend and
resume by disabling suspend while port_probe or port_remove is
running.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Use the buffer content length as opposed to the total buffer size. This can
be a real problem when using the mos7840 as a usb serial-console as all
kernel output is truncated during boot.
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this patch, we add new declarations into option.c to support the new
interfaces of Huawei Data Card devices. And at the same time, remove the
redundant declarations from option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds VID/PID for Kondo Kagaku Co. Ltd. Serial USB Adapter
interface:
http://www.kondo-robot.com/EN/wp/?cat=28
Tested by controlling an RCB3 board using libRCB3.
Signed-off-by: Ozan Çağlayan <ozancag@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we don't have tty->termios tied to drivers->tty we can untangle
the logic here. In addition we can push the removal logic out of the
destructor path.
At that point we can think about sorting out tty_port and console and all
the other ugly hangovers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sold by O2 (telefonica germany) under the name "LTE4G"
Tested-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MC7710 in QMI mode does not support the vendor
specific USB requests used by this driver. The most
noticable effect of this is a 5 second delay as each
serial port is probed, caused by the set_power_state
command timing out:
[ 17.434291] usbcore: registered new interface driver sierra
[ 17.434383] USB Serial support registered for Sierra USB modem
[ 17.434486] sierra 8-4:1.0: Sierra USB modem converter detected
[ 22.432413] usb 8-4: Sierra USB modem converter now attached to ttyUSB0
[ 22.432563] sierra 8-4:1.2: Sierra USB modem converter detected
[ 27.432410] usb 8-4: Sierra USB modem converter now attached to ttyUSB1
[ 27.432562] sierra 8-4:1.3: Sierra USB modem converter detected
[ 32.432463] usb 8-4: Sierra USB modem converter now attached to ttyUSB2
The MC7710 provide the same Qualcomm serial interfaces
as Gobi modules, and the qcserial driver has been extended
to support the module instead of this driver.
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QMI mode of the Sierra Wireless MC7710 is close to
a Gobi device, and also identified as one by the
Windows drivers provided by Sony. The serial interfaces
are the same as for any other Gobi module, but the USB
interface layout is different:
0: DM/DIAG (also present in bootloader mode)
2: NMEA
3: AT-capable modem port
8: QMI/net
19: QMI/net (not always present)
20: QMI/net (not always present)
Note in particular that the NMEA and AT ports are reversed
compared to a Gobi 2k+ device, and that the DM port appears
as a QDL port in bootloader mode using the same device ID.
The Sony driver also document two new devices with standard
Gobi 2k+ layout (1199:68a5, 1199:68a9) having a QDL mode
(1199:68a4, 1199:68a8). Adding these as well.
Lenovo Windows drivers document the USB interface layout
for a few additional Sierra Wireless devices. Adding these
while at it:
- MC7770 (1199:901b) with standard Gobi 2k+ layout
- MC7700 (0f3d:68a2) with the same layout as MC7710
- MC7750 (114f:68a2) with the same layout as MC7710
- EM7700 (1199:901c) with the same layout as MC7710
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to verify the interface layout when doing
interface number based matching. We can safely trust
the device ID table in this case.
This allows the driver to support any USB interface
layout for non-Gobi 1k/2k+ devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparing qcprobe support for more than just strict
Gobi 1k or 2k+ devices. Many newer Qualcomm based
devices provide the same serial ports, but using
varying USB interface layouts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creating a common exit path from qcprobe to make it
easier to extend it.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to replicate the same code all over the place.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - return is not a
function, parentheses not required. Removed 1 checkpatch.sh error.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - space near open
parenthesis '('. Removed 2 checkpatch.sh errors.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - space around '='.
Removed 1 checkpatch.sh error.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes to conform with checkpatch.sh script. - spaces around '?' and
':'. Removed 14 checkpatch.sh errors.
Signed-off-by: Ben Minerds <puzzleduck@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stuff noticed while doing the termios conversion.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not set low_latency flag at open as tty_flip_buffer_push must not be
called in IRQ context with low_latency set.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds 10 device IDs for CP210x based devices from the following manufacturers:
Timewave
Clipsal
Festo
Link Instruments
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is also known as the Verizon USB551L.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the serial port and tty changes in Linus's tree to allow
everyone to sync up.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lets us catch the USB fixes that went into 3.5-rc3 into this branch,
as we want them here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qt2_open() and qt2_close() both set a serial_priv variable but never
used it. Remove the variable from the functions.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
s_priv was set but never used in keyspan_open() and keyspan_close(),
remove it.
This also makes the serial variable in keyspan_open() unused since
it's only use was to set s_priv, so it is also removed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of kfree(serial) in error cases of usb_serial_probe
was invalid - usb_serial structure allocated in create_serial()
gets reference of usb_device that needs to be put, so we need
to use usb_serial_put() instead of simple kfree().
Signed-off-by: Jan Safrata <jan.nikitenko@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Determine whether to use send_setup at probe time rather than at every
call to send_setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up option probe by introducing intermediate variables and fixing
up comments.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is to pick up the changes to the option driver, which are needed
for follow-on patches from Johan.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_{get,set}_serial_data to access usb-serial data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb-serial-generic driver uses different device IDs for its USB
matching and its serial matching. This can lead to problems: The
driver can end up getting bound to a USB interface without being
allowed to bind to the corresponding serial port.
This patch (as1557) fixes the problem by using the same device ID
table (the one that can be altered by the "vendor=" and "product="
module parameters) for both purposes. The unused table is removed.
Now the driver will bind only to the intended devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to make sure that the USB serial driver we find
matches the USB driver whose probe we are currently
executing. Otherwise we will end up with USB serial
devices bound to the correct serial driver but wrong
USB driver.
An example of such cross-probing, where the usbserial_generic
USB driver has found the sierra serial driver:
May 29 18:26:15 nemi kernel: [ 4442.559246] usbserial_generic 4-4:1.0: Sierra USB modem converter detected
May 29 18:26:20 nemi kernel: [ 4447.556747] usbserial_generic 4-4:1.2: Sierra USB modem converter detected
May 29 18:26:25 nemi kernel: [ 4452.557288] usbserial_generic 4-4:1.3: Sierra USB modem converter detected
sysfs view of the same problem:
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/sierra
-rw-r--r-- 1 root root 4096 May 29 18:23 new_id
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0/ttyUSB0
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB1 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2/ttyUSB1
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3/ttyUSB2
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/usbserial_generic/
total 0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.3 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/generic/
total 0
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
-rw-r--r-- 1 root root 4096 May 29 18:33 new_id
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
So we end up with a mismatch between the USB driver and the
USB serial driver. The reason for the above is simple: The
USB driver probe will succeed if *any* registered serial
driver matches, and will use that serial driver for all
serial driver functions.
This makes ref counting go wrong. We count the USB driver
as used, but not the USB serial driver. This may result
in Oops'es as demonstrated by Johan Hovold <jhovold@gmail.com>:
[11811.646396] drivers/usb/serial/usb-serial.c: get_free_serial 1
[11811.646443] drivers/usb/serial/usb-serial.c: get_free_serial - minor base = 0
[11811.646460] drivers/usb/serial/usb-serial.c: usb_serial_probe - registering ttyUSB0
[11811.646766] usb 6-1: pl2303 converter now attached to ttyUSB0
[11812.264197] USB Serial deregistering driver FTDI USB Serial Device
[11812.264865] usbcore: deregistering interface driver ftdi_sio
[11812.282180] USB Serial deregistering driver pl2303
[11812.283141] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[11812.283272] usbcore: deregistering interface driver pl2303
[11812.301056] USB Serial deregistering driver generic
[11812.301186] usbcore: deregistering interface driver usbserial_generic
[11812.301259] drivers/usb/serial/usb-serial.c: usb_serial_disconnect
[11812.301823] BUG: unable to handle kernel paging request at f8e7438c
[11812.301845] IP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.301871] *pde = 357ef067 *pte = 00000000
[11812.301957] Oops: 0000 [#1] PREEMPT SMP
[11812.301983] Modules linked in: usbserial(-) [last unloaded: pl2303]
[11812.302008]
[11812.302019] Pid: 1323, comm: modprobe Tainted: G W 3.4.0-rc7+ #101 Dell Inc. Vostro 1520/0T816J
[11812.302115] EIP: 0060:[<f8e38445>] EFLAGS: 00010246 CPU: 1
[11812.302130] EIP is at usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.302141] EAX: f508a180 EBX: f508a180 ECX: 00000000 EDX: f8e74300
[11812.302151] ESI: f5050800 EDI: 00000001 EBP: f5141e78 ESP: f5141e58
[11812.302160] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[11812.302170] CR0: 8005003b CR2: f8e7438c CR3: 34848000 CR4: 000007d0
[11812.302180] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[11812.302189] DR6: ffff0ff0 DR7: 00000400
[11812.302199] Process modprobe (pid: 1323, ti=f5140000 task=f61e2bc0 task.ti=f5140000)
[11812.302209] Stack:
[11812.302216] f8e3be0f f8e3b29c f8e3ae00 00000000 f513641c f5136400 f513641c f507a540
[11812.302325] f5141e98 c133d2c1 00000000 00000000 f509c400 f513641c f507a590 f5136450
[11812.302372] f5141ea8 c12f0344 f513641c f507a590 f5141ebc c12f0c67 00000000 f507a590
[11812.302419] Call Trace:
[11812.302439] [<c133d2c1>] usb_unbind_interface+0x51/0x190
[11812.302456] [<c12f0344>] __device_release_driver+0x64/0xb0
[11812.302469] [<c12f0c67>] driver_detach+0x97/0xa0
[11812.302483] [<c12f001c>] bus_remove_driver+0x6c/0xe0
[11812.302500] [<c145938d>] ? __mutex_unlock_slowpath+0xcd/0x140
[11812.302514] [<c12f0ff9>] driver_unregister+0x49/0x80
[11812.302528] [<c1457df6>] ? printk+0x1d/0x1f
[11812.302540] [<c133c50d>] usb_deregister+0x5d/0xb0
[11812.302557] [<f8e37c55>] ? usb_serial_deregister+0x45/0x50 [usbserial]
[11812.302575] [<f8e37c8d>] usb_serial_deregister_drivers+0x2d/0x40 [usbserial]
[11812.302593] [<f8e3a6e2>] usb_serial_generic_deregister+0x12/0x20 [usbserial]
[11812.302611] [<f8e3acf0>] usb_serial_exit+0x8/0x32 [usbserial]
[11812.302716] [<c1080b48>] sys_delete_module+0x158/0x260
[11812.302730] [<c110594e>] ? mntput+0x1e/0x30
[11812.302746] [<c145c3c3>] ? sysenter_exit+0xf/0x18
[11812.302746] [<c107777c>] ? trace_hardirqs_on_caller+0xec/0x170
[11812.302746] [<c145c390>] sysenter_do_call+0x12/0x36
[11812.302746] Code: 24 02 00 00 e8 dd f3 20 c8 f6 86 74 02 00 00 02 74 b4 8d 86 4c 02 00 00 47 e8 78 55 4b c8 0f b6 43 0e 39 f8 7f a9 8b 53 04 89 d8 <ff> 92 8c 00 00 00 89 d8 e8 0e ff ff ff 8b 45 f0 c7 44 24 04 2f
[11812.302746] EIP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial] SS:ESP 0068:f5141e58
[11812.302746] CR2: 00000000f8e7438c
Fix by only evaluating serial drivers pointing back to the
USB driver we are currently probing. This still allows two
or more drivers to match the same device, running their
serial driver probes to sort out which one to use.
Cc: stable@vger.kernel.org # 3.0, 3.2, 3.3, 3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __devinitconst section can't be referenced
from usb_serial_device structure. Thus removed it as
it done in other mos* device drivers.
Error itself:
WARNING: drivers/usb/serial/mos7840.o(.data+0x8): Section mismatch in reference
from the variable moschip7840_4port_device to the variable
.devinit.rodata:id_table
The variable moschip7840_4port_device references
the variable __devinitconst id_table
[v2] no attach now
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leak introduced by commit 383cedc3bb ("USB: serial:
full autosuspend support for the option driver") which allocates
usb-serial data but never frees it.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b4c6a3ab5 ("USB: option: Use generic USB wwan code")
moved option port-data allocation to usb_wwan_startup but still cast the
port data to the old struct...
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low level helper returns 1 on success. The ioctl should however return
0. As this is the only user of the helper return, make the helper return 0 or
an error code.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43009
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Later firmwares for this device now have proper subclass and
protocol info so we can identify it nicely without needing to use
the blacklist. I'm not removing the old 0xff matching as there
may be devices in the field that still need that.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Sierra Wireless AirCard 320U modem
Signed-off-by: Tomas Cassidy <tomas.cassidy@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RT Systems USB-RTS01 USB to Serial adapter:
http://www.rtsystemsinc.com/Photos/USBRTS01.html
Tested by controlling Icom IC-718 amateur radio transceiver via hamlib.
Signed-off-by: Evan McNabb <evan@mcnabbs.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some additional IDs found in the BSD/GPL licensed out-of-tree
GobiSerial driver from Sierra Wireless.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6971113e10.
As Alan pointed out, this really isn't needed as it doesn't handle this
properly. Ideally this should be handled by the usb-serial core one
day. So revert it.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the usb-serial driver doesn't have a reset_resume callback, then we
need to tell the USB core that it doesn't, and it needs to rebind the
device.
Thanks to Alan for pointing out my mistake, and providing the fix.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I hooked up the wrong callback in my previous patch, this should fix it.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make some noise during probe to make sure the users
are aware of the intended purpose of this driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the symbolserial.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the spcp8x5.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the qcserial.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Thomas Tuttle <ttuttle@chromium.org>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the navman.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the ir-usb.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the ipaq.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the generic.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the f81232.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the belkin_sa.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the ark3116.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the aircable.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few patches ago, I removed the reset_resume callback in this driver.
Now that the usb-serial core supports reset_resume, put this driver
callback back as well, so it should work identically to how it was
originally.
Now if this function really is doing what it should be doing, well,
that's a different story, but we are at least doing the identical thing
that we were before...
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few patches ago, I removed the reset_resume callback, changing it to
resume instead. Now that the usb-serial core supports reset_resume, put
this driver callback back as well, so it should work identically to how
it was originally.
Now if this function really is doing what it should be doing, well,
that's a different story, but we are at least doing the identical thing
that we were before...
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The callback is now hooked up for any USB to serial driver that wants
it. We only register the callback if any of the usb-serial structures
want it, this keeps the USB core happy.
Thanks to Alan Stern for the ideas on how to do this.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep the usb-serial support for dynamic IDs in sync with the usb
support. This enables readout of dynamic device IDs for
usb-serial drivers. Common code is exported from the usb core
system and reused by the usb-serial bus driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kontron M2M development board, also known as the Fish River Island II,
has an optional daughter card providing access to the PCH_UART (EG20T) via
a ti_usb_3410_5052 uart to usb chip.
http://us.kontron.com/products/systems+and+platforms/m2m/m2m+smart+services+developer+kit.html
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Al Borchers <alborchers@steinerpoint.com>
CC: Peter Berger <pberger@brimson.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a previous patch, the usb_driver suspend/resume callbacks got
overridden and were never called if a usb_serial driver defined them.
This patch fixes the opticon driver to move the suspend/resume callbacks
into the usb_serial_driver structure where they will be properly called.
It then removes the unused usb_driver structure.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a copyright and license statement to the head of quatech.c source
file. No code change here.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This supports the Quatech USB 2 usb to serial adapters.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reworks the usb_serial_register_drivers() and
usb_serial_deregister_drivers() to not need a pointer to a struct
usb_driver anymore. The usb_driver structure is now created dynamically
and registered and unregistered as needed.
This saves lines of code in each usb-serial driver. All in-kernel users
of these functions were also fixed up at this time. The pl2303 driver
was tested that everything worked properly.
Thanks for the idea to do this from Alan Stern.
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Support Department <support@connecttech.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds VID/PID for the PI E-861. Without it, I had to do:
modprobe -q ftdi-sio product=0x1008 vendor=0x1a72
http://www.physikinstrumente.com/en/products/prdetail.php?sortnr=900610
Signed-off-by: Éric Piel <piel@delmic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I can't remember why I wrote it like this many many years ago, but it's
not needed at all, let's rely on the usb-serial core for this function,
especially as it is being overridden by it anyway.
This lets us make usb_serial_probe() a static function, which it should
be.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This really just is the resume callback for the device, so use that,
especially as the usb-serial core just overrode this callback so it
wasn't being made anyway.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This really just is the resume callback for the device, so use that,
especially as the usb-serial core just overrode this callback so it
wasn't being made anyway.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now set by the usb-serial core, no need for the driver to
individually set it.
Thanks to Alan Stern for the idea to get rid of it.
Cc: William Greathouse <wgreathouse@smva.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Support Department <support@connecttech.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Julia Lawall <julia@diku.dk>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now set by the usb-serial core, no need for the driver to
individually set it.
Thanks to Alan Stern for the idea to get rid of it.
Cc: William Greathouse <wgreathouse@smva.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Support Department <support@connecttech.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Julia Lawall <julia@diku.dk>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1551) cleans up the PM-related entries in the usb_driver
structures of the various USB serial driver modules. Those entries
are now filled in by the usb-serial core during driver registration,
so they don't need to be initialized explicitly in the source code.
The same is true of the one remaining no_dynamic_id entry.
reset_resume remains a small problem, because the serial core doesn't
support it. The patch ignores these entries.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1550) fixes a bug in the usb-serial core that affects
the ftdi_sio driver and most likely others as well. The core
implements suspend and resume routines, but it doesn't store pointers
to those routines in the usb_driver structures that it registers,
even though it does set those drivers' supports_autosuspend flag. The
end result is that when one of these devices is autosuspended, we try
to call through a NULL pointer.
The patch fixes the problem by setting the suspend and resume method
pointers to the appropriate routines in the USB serial core, along
with the supports_autosuspend field, in each driver as it is
registered.
This should be back-ported to all the stable kernels that have the new
usb_serial_register_drivers() interface.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Frank Schäfer <schaefer.frank@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Support Department <support@connecttech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Johan Hovold <jhovold@gmail.com>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Johan Hovold <jhovold@gmail.com>
CC: Anton Samokhvalov <pg83@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
![](/avatar/dabfd77a895665bf8b3c6da6e021895d?size=56 "Alexandr \\"Sky\\" Ivanov"){kind=small}
