netif_device_detach() stops all tx queues already, so we don't need
this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this function, no functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added driver causes a warning about a function that is
not used anywhere:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:320:12: error: 'cgx_fwi_link_change' defined but not used [-Werror=unused-function]
Remove it for now, until a user gets added. If we want to use this
function from another module, we also need a declaration in a header
file, which is currently missing, so it would have to change anyway.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: Ryan C Goodfellow <rgoodfel@isi.edu>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Greg Weeks <greg.weeks@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware ArchDef, the PTV1 field in FD[CTRL]
is ignored by WRIOP, so setting it for Tx FDs is pointless.
Remove all references to it from the code.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ch parameter is never used in the dpaa2_eth_tx_conf function but
since its prototype must match the type defined in the consume field of
struct dpaa2_eth_fq, just mark it as __always_unused.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv parameter is never used in the build_linear_skb and
drain_channel function. Remove it from the function definitions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 3 cases of possible uninitialized variables are false
positives since they are used only as output parameters.
Nonetheless, fix the warnings.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2_eth_set_dist_key function is only used in a single file.
Make it static.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ARCH_LAYERSCAPE and COMPILE_TEST dependencies are already implied
through the FSL_MC_BUS dep, so there's no need to state it explicitly.
Also, the fsl-mc bus depends on COMPILE_TEST only for some
architectures (arm, arm64, ppc, x86), so it's not correct to
claim build support unconditionally.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dual-emac mode the cpsw driver sends directed packets, that means
that packets go to the directed port, but an ALE lookup is performed
to determine untagged egress only. It means that on tx side no need
to add port bit for ALE mcast entry mask, and basically ALE entry
for port identification is needed only on rx side.
So, add only host port in dual_emac mode as used directed
transmission, and no need in one more port. For single port boards
and switch mode all ports used, as usual, so no changes for them.
Also it simplifies farther changes.
In other words, mcast entries for dual-emac should behave exactly
like unicast. It also can help avoid leaking packets between ports
with same vlan on h/w level if ports could became members of same vid.
So now, for instance, if mcast address 33:33:00:00:00:01 is added then
entries in ALE table:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x1
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x1
Instead of:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x3
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x5
With the same considerations, set only host port for unregistered
mcast for dual-emac mode in case of IFF_ALLMULTI is set, exactly like
it's done in cpsw_ale_set_allmulti().
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever kernel or user decides to call rx mode update, it clears
every multicast entry from forwarding table and in some time adds
it again. This time can be enough to drop incoming multicast packets.
That's why clear only staled multicast entries and update or add new
one afterwards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It allows to use function under callbacks with same const qualifier of
mac address for farther changes.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On GENETv5, there is a hardware issue which prevents the GENET hardware
from generating a link UP interrupt when the link is operating at
10Mbits/sec. Since we do not have any way to configure the link
detection logic, fallback to polling in that case.
Fixes: 421380856d ("net: bcmgenet: add support for the GENETv5 hardware")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify code for handling state PHY_RESUMING, no functional change
intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling of state PHY_RUNNING seems to be more complex than it needs
to be. If not polling, then we don't have to do anything, we'll
receive an interrupt and go to state PHY_CHANGELINK once the link
goes down. If polling and link is down, we don't have to go the
extra mile over PHY_CHANGELINK and call phy_read_status() again
but can set status PHY_NOLINK directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes use of NTF_USE in vxlan driver consistent
with bridge driver.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the state machine there may be work to be done
immediately, e.g. if the initial state is PHY_UP then the state
machine may trigger an autonegotiation. Having said that I see no need
to wait a second until the state machine is run first time.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose per-queue stats for ethtool -S.
As there are only rx queues, and rx queues are used only when XDP is
used, per-queue counters are only rx XDP ones.
Example:
$ ethtool -S veth0
NIC statistics:
peer_ifindex: 11
rx_queue_0_xdp_packets: 28601434
rx_queue_0_xdp_bytes: 1716086040
rx_queue_0_xdp_drops: 28601434
rx_queue_1_xdp_packets: 17873050
rx_queue_1_xdp_bytes: 1072383000
rx_queue_1_xdp_drops: 17873050
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
On XDP path veth has napi handler so we can collect statistics on
per-queue basis for XDP.
By this change now we can collect XDP_DROP drop count as well as packets
and bytes coming through ndo_xdp_xmit. Packet counters shown by
"ip -s link", sysfs stats or /proc/net/dev is now correct for XDP.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing atomic drop counter. Since drop path is really an
exceptional case here, I'm thinking atomic ops would not hurt the
performance.
XDP packets and bytes are not counted in ndo_xdp_xmit, but will be
accounted on rx side by the following commit.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbvqcMAAoJEEg/ir3gV/o+eFsH/2TbJH+i1BuGMVwCB8o+U1Rz
C01pJmR7Lb7WwQZ8ZKTOqQkS7BkGX1hNGyIlc4i6ZnP+4gsVJAbP6LKPjTvyD7e6
TNb8bvxTUCOovknrevKkGba8tzoTTsC4wwwbHLGHd1hkKSY1P5hXg8R7vpear+n6
/PFJwzpIXDAa8AHqeORCNYj7MneUm3kaahcmSOxOhvDbRx3UG9cgy7tEhPjZbRn5
jPFsxFCSPcGedtI+g8bzodmpneTcu1KF6QCunrl2bGt5EzgDrbaw1UUoctxD2CJR
Ch45W807EvBJoFiJXXCNf9N+p5020F/Q+mTmK7khPirUjdtoLdcT9Goswpjfbtk=
=vJIA
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-10-10
This pull request includes some fixes to mlx5 driver,
Please pull and let me know if there's any problem.
For -stable v4.11:
('net/mlx5: Take only bit 24-26 of wqe.pftype_wq for page fault type')
For -stable v4.17:
('net/mlx5: Fix memory leak when setting fpga ipsec caps')
For -stable v4.18:
('net/mlx5: WQ, fixes for fragmented WQ buffers API')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IPoIB netlink support and mlx5e pre-allocated netdevice initialization
IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit cd565b4b51
("IB/IPoIB: Support acceleration options callbacks").
This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:
From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
creation.
From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
queue number.
5) Initialize mlx5e generic structures in one place to be used for all
netdevs types NIC/representors/IPoIB (both mlx5 allocated and
pre-allocted).
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbvqHhAAoJEEg/ir3gV/o+TRQH+wYWgvi5AbqYlGpT8xSho8Dg
5tuFE9AbYDGLLWptZgtYXsBsTaltGVqKnwWy//dAuuSI7LvqtjeKqq0G1JKau70L
/49+vv8NTQ6vov2yY95yzzEo5B1/zVcYEl9dmJl4y6Xlwc+YIteewReVqRj+tucR
xO7ghLWc1o4Pl7gWBAcOULyOsZc+CtG8ElwEaBROXTtYRpsR7FKn7vN+WdWZ2VOG
MjtCUaG0vZlK1vaF76J3P9bL2V3y6o6i6S8RZwg1kPxO4jnrzyGrkxWMOX6f32KB
JAUcLVlJW5wckcRAKfTwLxsFMrc9vLBPHyj4XneXVWGKh8/dGUGY5gdGIJV5Jlc=
=m0tM
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-10-10' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-10-10
IPoIB netlink support and mlx5e pre-allocated netdevice initialization
IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit cd565b4b51
("IB/IPoIB: Support acceleration options callbacks").
This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:
From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
creation.
From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
queue number.
5) Initialize mlx5e generic structures in one place to be used for all
netdevs types NIC/representors/IPoIB (both mlx5 allocated and
pre-allocted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware. Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process. Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.
When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.
However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps. This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.
Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the DEC FDDIcontroller 700 (DEFZA), Digital Equipment
Corporation's first-generation FDDI network interface adapter, made for
TURBOchannel and based on a discrete version of what eventually became
Motorola's widely used CAMEL chipset.
The CAMEL chipset is present for example in the DEC FDDIcontroller
TURBOchannel, EISA and PCI adapters (DEFTA/DEFEA/DEFPA) that we support
with the `defxx' driver, however the host bus interface logic and the
firmware API are different in the DEFZA and hence a separate driver is
required.
There isn't much to say about the driver except that it works, but there
is one peculiarity to mention. The adapter implements two Tx/Rx queue
pairs.
Of these one pair is the usual network Tx/Rx queue pair, in this case
used by the adapter to exchange frames with the ring, via the RMC (Ring
Memory Controller) chip. The Tx queue is handled directly by the RMC
chip and resides in onboard packet memory. The Rx queue is maintained
via DMA in host memory by adapter's firmware copying received data
stored by the RMC in onboard packet memory.
The other pair is used to communicate SMT frames with adapter's
firmware. Any SMT frame received from the RMC via the Rx queue must be
queued back by the driver to the SMT Rx queue for the firmware to
process. Similarly the firmware uses the SMT Tx queue to supply the
driver with SMT frames that must be queued back to the Tx queue for the
RMC to send to the ring.
This solution was chosen because the designers ran out of PCB space and
could not squeeze in more logic onto the board that would be required to
handle this SMT frame traffic without the need to involve the driver, as
with the later DEFTA/DEFEA/DEFPA adapters.
Finally the driver does some Frame Control byte decoding, so to avoid
magic numbers some macros are added to <linux/if_fddi.h>.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.
This can be visualized with following ip-link(8) command sequences:
# ip link set dev tun0 group 100
# ip link set dev tun0 group 100 type tun
RTNETLINK answers: Invalid argument
with contrast to dummy and veth drivers:
# ip link set dev dummy0 group 100
# ip link set dev dummy0 type dummy
# ip link set dev veth0 group 100
# ip link set dev veth0 group 100 type veth
Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.
Fixes: f019a7a594 ("tun: Implement ip link del tunXXX")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally, we have an issue where r8169 MSI-X interrupt is broken after
S3 suspend/resume on RTL8106e of ASUS X441UAR.
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable+ Count=4 Masked-
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-00-00-00-36-4c-e0-00
Capabilities: [170] Latency Tolerance Reporting
Kernel driver in use: r8169
Kernel modules: r8169
We found the all of the values in PCI BAR=4 of the ethernet adapter
become 0xFF after system resumes. That breaks the MSI-X interrupt.
Therefore, we can only fall back to MSI interrupt to fix the issue at
that time.
However, there is a commit which resolves the drivers getting nothing in
PCI BAR=4 after system resumes. It is 04cb3ae895d7 "PCI: Reprogram
bridge prefetch registers on resume" by Daniel Drake.
After apply the patch, the ethernet adapter works fine before suspend
and after resume. So, we can revert the workaround after the commit
"PCI: Reprogram bridge prefetch registers on resume" is merged into main
tree.
This patch reverts commit 7bb05b85bc
"r8169: don't use MSI-X on RTL8106e".
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=201181
Fixes: 7bb05b85bc ("r8169: don't use MSI-X on RTL8106e")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* mt76x0 fixes
* mt76x0e improvements (should be usable now)
* usb support improvements
* more mt76x0/mt76x2 unification work
* minor fix for aggregation + powersave clients
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlvCEgoACgkQ130UHQKnbvU4RQCeKXCe/rgtrGQ0KXjcuZbXfYmn
2pAAoKLCTrI9QTCScMnTdyfHqiRCEBF8
=wK37
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2018-10-13' of https://github.com/nbd168/wireless
mt76 patches for 4.20
* mt76x0 fixes
* mt76x0e improvements (should be usable now)
* usb support improvements
* more mt76x0/mt76x2 unification work
* minor fix for aggregation + powersave clients
Add WCN3990 QMI client handshakes for Q6 integrated WLAN connectivity
subsystem. This layer is responsible for communicating qmi control
messages to wifi fw QMI service using QMI messaging protocol.
Qualcomm MSM Interface(QMI) is a messaging format used to communicate
between components running between remote processors with underlying
transport layer based on integrated chipset(shared memory) or
discrete chipset(PCI/USB/SDIO/UART).
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debug mask to control debug info of ath10k qmi
messaging layer.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support to create the boardname for non-bmi targets
like WCN3990, which uses qmi for bdf download. This
boardname is used to parse the board data from board-2.bin.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A couple of macros that deal with statistics in ath9k rely on the
declaration of the 'sc' variable, which they dereference.
However, when the statistics are disabled, the new instance in
ath_cmn_process_fft() causes a warning for an unused variable:
drivers/net/wireless/ath/ath9k/common-spectral.c: In function 'ath_cmn_process_fft':
drivers/net/wireless/ath/ath9k/common-spectral.c:474:20: error: unused variable 'sc' [-Werror=unused-variable]
It's better if those macros only operate on their arguments instead of
known variable names, and adding a cast to (void) kills off that warning.
Fixes: 03224678c0 ("ath9k: add counters for good and errorneous FFT/spectral frames")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We added an unnecessary condition here in commit a904417fc8 ("ath10k:
add extended per sta tx statistics support"). "legacy_rate_idx" is a u8
so it can't be negative. The caller doesn't pass negatives either. I
have deleted this code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_pci_diag_write_mem may allocate big size of the dma memory
based on the parameter nbytes. Take firmware diag download as
example, the biggest size is about 500K. In some systems, the
allocation is likely to fail because it can't acquire such a large
contiguous dma memory.
The fix is to allocate a small size dma memory. In the loop,
driver copies the data to the allocated dma memory and writes to
the destination until all the data is written.
Tested with QCA6174 PCI with
firmware-6.bin_WLAN.RM.4.4.1-00119-QCARMSWP-1, this also affects
QCA9377 PCI.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chomium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the noisy environment, if there are packets in the queue and can't
send out, the suspend timing will be more than 5 seconds due to the wait,
flush the queue to optimize the suspend timing, and let the upper layer to
retry the packets after resume.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to compare *ps_state_enable* with < 0 because
such variable is of type u8 (8 bits, unsigned), making it
impossible to hold a negative value.
Fix this by removing such comparison.
Addresses-Coverity-ID: 1473921 ("Unsigned compared against 0")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the error handling for the call to function
ath10k_get_legacy_rate_idx() doesn't work because
*rate_idx* is of type u8 (8 bits, unsigned), which
makes it impossible for it to hold a value less
than 0.
Fix this by changing the type of variable *rate_idx*
to s8 (8 bits, signed).
Addresses-Coverity-ID: 1473914 ("Unsigned compared against 0")
Fixes: 0189dbd71c ("ath10k: get the legacy rate index to update the txrate table")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding WMI service check for management tx ack rssi support; this is
done to maintain common avg ack signal in user level for both data
and management tx ack packet.
Tested on QCA4019(fw version-10.4-3.2.1-00063).
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For WoWLAN support it is expected to support wake up based on discovery of
one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature,
which shows up as an NL80211 feature flag.
This shows up in 'iw phy' as:
WoWLAN support:
* wake up on network detection, up to 16 match sets
And it can be enabled with command:
iw phy0 wowlan enable net-detect interval 5000 delay 30 freqs 2412 matches ssid foo
Firmware will do scan by the configured parameters after suspend and
wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with
firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the wmi command for setting probe request
oui, needed for mac randomization, is sent during
the mac register. At this time, during the driver
init the wmi has already been detached. This can
cause unexpected behavior since the firmware is
already down and the wmi has been detached.
Send the wmi command for setting probe request
oui during the driver start. This will make sure
that the firmware is started and wmi is initialized
before we send this command.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 60e1d0fb29
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While using 'ath10k_mac_get_rate_hw_value()' to obtain the hw value
from the passed bitrate, there is a chance of out of bound array access
when wrong bitrate is passed. This is fixed by comparing the bitrates
within the correct size of the ath10k_rates array.
Fixes commit f279294e9e ("ath10k: add support for configuring management
packet rate"). Also correction made to some indents used in the above commit.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c: In function 'rtl8xxxu_tx':
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4925:7: warning:
variable 'usedesc40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4921:6: warning:
variable 'seq_number' set but not used [-Wunused-but-set-variable]
'usedesc40' and 'seq_number' are not used any more after
commit b59415c2dd ("rtl8xxxu: Split filling of TX descriptors into separate functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove redundant information from Pearl platform headers.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change pcie bus layer licensing information to SPDX format.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix checkpatch warning: use preferred 'help' option in Kconfig.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes the error handling somewhat cleaner -- lbs_add_card() does no
logner throw away the errno and lets its callers propagate it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variables il->staging.filter_flags, rxon1->filter_flags and
rxon2->filter_flags need to be protected by the mutex lock il->mutex.
This patch adds a lock assertion of il->mutex to check whether
this lock is held.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Beacons are not updated to reflect TIM changes. This is not compliant with
power-saving client stations as the beacons do not have valid TIM and can
cause the network to stall at random occasions and to have highly variable
latencies.
Fix it by updating beacon templates on mac80211 set_tim callback.
Addresses an issue described in:
https://marc.info/?i=20180911163534.21312d08%20()%20manjaro
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not perform phy/vga calibration during channel switch.
Moreover remove mt76x0_agc_save and mt76x0_agc_restore routines
since they are no longer necessary. Furthermore run mt76_set_channel
in order to check if there are pending frames during channel switch
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update vga tuning algorithm to the one used in mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_init_agc_gain routine in mt76x02-lib moudule in
order to be reused by mt76x0 for vga initalization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_adjust_vga_gain routine in mt76x02-lib module
in order to be reused by mt76x0 driver for vga calibration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_get_rssi_gain_thresh and mt76x2_get_low_rssi_gain_thresh
routines in mt76x02-lib module in order to be reused by mt76x0 driver
for dynamic vga calibration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce phy/vco temperature calibration.
Moreover fix configuration of register 67 on bank0
during temperature reading and use mt76_poll utility routine
to poll core34 register.
Furthermore temperature compensation needs to be disabled
if the device supports tssi compensation.
This issue has never been hit since temperature reading is not
actually used by usb code.
Fixes: 10de7a8b4a ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_tssi_enabled in order to check if tssi compensation
is enabled since mt76x0 condition differs from mt76x2 one.
Moreover move back mt76x02_temp_tx_alc_enabled and mt76x02_tssi_enabled
routines in mt76x2/eeprom.h since they are mt76x2 specific
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not run mt76x0_vco_cal and mt76x0_bbp_set_bw routines and
configure MT_TX_SW_CFG0 register for pcie devices in
mt76x0_phy_set_channel function.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_phy_calirate routine in order to perform
phy calibration for mt76x0e devices.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename mt76x0_phy_calibrate routine in mt76x0_phy_calibration_work
in order to not collide with calibration routine for mt76x0e
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_set_band routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_set_bw routine in mt76x02_phy.c since
it is shared between mt76x0 and mt76x2 drivers and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix restore value configured in MT_BBP(IBI, 9) register in
mt76x0_phy_recalibrate_after_assoc routine.
Fixes: 10de7a8b4a ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- Use the register number define instead of a magic value
- Fix inverted bit test (override needs to be applied if the bit is not set)
Fixes: 2b2cb40bcd ("mt76x0: pci: add hw initialization at bootstrap")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/mediatek/mt76/mt76x0/pci.c: In function 'mt76x0e_register_device':
drivers/net/wireless/mediatek/mt76/mt76x0/pci.c:107:8: warning:
variable 'data' set but not used [-Wunused-but-set-variable]
It seems correct value to write is 'data'
Fixes: 2b2cb40bcd ("mt76x0: pci: add hw initialization at bootstrap")
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reserve enough room for USB skb, so we don not need to check
the room every time we send frame.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76x0_register_device routine in mt76x0e_register_device
in order to register the device to the mac80211 layer.
Moreover init mt76_driver_ops data structure and register
interrupt line
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable ldpc coding for mt76x0 devices. Morover remove
mt76x02_mac_fill_txwi routine since it is used just in
mt76x02_mac_write_txwi
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add missing mac80211 callbacks in mt76x0e_ops data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Report via ethtool fw_ver and build_ver members of mt76x02_fw_header
data structure similarly to what is reported in the syslog
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_eeprom.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_txrx.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_mac.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_usb_mcu.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_util.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_phy.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_mcu.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix typo in bank check in mt76x0_rf_csr_{wr,rr} routines.
This issue has never been hit since mt76x0_rf_csr_{wr,rr}
are actually used just by pci code
Fixes: 10de7a8b4a ("mt76x0: phy files")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76_is_usb() to identify RF access method instead of
MT76_STATE_MCU_RUNNING flag and add warning since MCU has
to be initialized before we can access RF registers via MCU.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
PCIe version don't use MCU for RF registers access. We need
to correct RF CSR method to support up to 127 RF registers.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.
This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")
Thanks to Joe Perches for spotting this when I submitted an earlier patch.
Fixes: 3c05bedb5f ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access. This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Support for a new scan type;
* Clean-up in the queue handling code;
* A few bug fixes;
-----BEGIN PGP SIGNATURE-----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=etyT
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Fourth set of iwlwifi patches intended for 4.20
* Support for a new scan type;
* Clean-up in the queue handling code;
* A few bug fixes;
First of all, make it return int. Returning long when native method
had never allowed that is ridiculous and inconvenient.
More importantly, change the caller; if ldisc ->compat_ioctl() is NULL
or returns -ENOIOCTLCMD, tty_compat_ioctl() will try to feed cmd and
compat_ptr(arg) to ldisc's native ->ioctl().
That simplifies ->compat_ioctl() instances quite a bit - they only
need to deal with ioctls that are neither generic tty ones (those
would get shunted off to tty_ioctl()) nor simple compat pointer ones.
Note that something like TCFLSH won't reach ->compat_ioctl(),
even if ldisc ->ioctl() does handle it - it will be recognized
earlier and passed to tty_ioctl() (and ultimately - ldisc ->ioctl()).
For many ldiscs it means that NULL ->compat_ioctl() does the
right thing. Those where it won't serve (see e.g. n_r3964.c) are
also easily dealt with - we need to handle the numeric-argument
ioctls (calling the native instance) and, if such would exist,
the ioctls that need layout conversion, etc.
All in-tree ldiscs dealt with.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resumes promisc mode and vlan filter status after
loopback test.
Fixes: 3b75c3df59 ("net: hns3: net: hns3: Add support for IFF_ALLMULTI flag")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resumes promisc mode and vlan filter status after reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* merge net-next, so I can finish the hwsim workqueue removal
* fix TXQ NULL pointer issue that was reported multiple times
* minstrel cleanups from Felix
* simplify lib80211 code by not using skcipher, note that this
will conflict with the crypto tree (and this new code here
should be used)
* use new netlink policy validation in nl80211
* fix up SAE (part of WPA3) in client-mode
* FTM responder support in the stack
-----BEGIN PGP SIGNATURE-----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=RqMD
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Highlights:
* merge net-next, so I can finish the hwsim workqueue removal
* fix TXQ NULL pointer issue that was reported multiple times
* minstrel cleanups from Felix
* simplify lib80211 code by not using skcipher, note that this
will conflict with the crypto tree (and this new code here
should be used)
* use new netlink policy validation in nl80211
* fix up SAE (part of WPA3) in client-mode
* FTM responder support in the stack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/cdc_ncm.c: In function 'cdc_ncm_status':
drivers/net/usb/cdc_ncm.c:1603:22: warning:
variable 'ctx' set but not used [-Wunused-but-set-variable]
struct cdc_ncm_ctx *ctx;
It not used any more after
commit fa83dbeee5 ("net: cdc_ncm: remove redundant "disconnected" flag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Avoid fragile multiblock reads for the last sector in SPI mode
WIFI/SDIO:
- libertas: Fixup suspend sequence for the SDIO card
-----BEGIN PGP SIGNATURE-----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=s+ye
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Ulf writes:
"MMC core:
- Avoid fragile multiblock reads for the last sector in SPI mode
WIFI/SDIO:
- libertas: Fixup suspend sequence for the SDIO card"
* tag 'mmc-v4.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
libertas: call into generic suspend code before turning off power
mmc: block: avoid multiblock reads for the last sector in SPI mode
David writes:
"Networking
1) RXRPC receive path fixes from David Howells.
2) Re-export __skb_recv_udp(), from Jiri Kosina.
3) Fix refcounting in u32 classificer, from Al Viro.
4) Userspace netlink ABI fixes from Eugene Syromiatnikov.
5) Don't double iounmap on rmmod in ena driver, from Arthur
Kiyanovski.
6) Fix devlink string attribute handling, we must pull a copy into a
kernel buffer if the lifetime extends past the netlink request.
From Moshe Shemesh.
7) Fix hangs in RDS, from Ka-Cheong Poon.
8) Fix recursive locking lockdep warnings in tipc, from Ying Xue.
9) Clear RX irq correctly in socionext, from Ilias Apalodimas.
10) bcm_sf2 fixes from Florian Fainelli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: dsa: bcm_sf2: Call setup during switch resume
net: dsa: bcm_sf2: Fix unbind ordering
net: phy: sfp: remove sfp_mutex's definition
r8169: set RX_MULTI_EN bit in RxConfig for 8168F-family chips
net: socionext: clear rx irq correctly
net/mlx4_core: Fix warnings during boot on driverinit param set failures
tipc: eliminate possible recursive locking detected by LOCKDEP
selftests: udpgso_bench.sh explicitly requires bash
selftests: rtnetlink.sh explicitly requires bash.
qmi_wwan: Added support for Gemalto's Cinterion ALASxx WWAN interface
tipc: queue socket protocol error messages into socket receive buffer
tipc: set link tolerance correctly in broadcast link
net: ipv4: don't let PMTU updates increase route MTU
net: ipv4: update fnhe_pmtu when first hop's MTU changes
net/ipv6: stop leaking percpu memory in fib6 info
rds: RDS (tcp) hangs on sendto() to unresponding address
net: make skb_partial_csum_set() more robust against overflows
devlink: Add helper function for safely copy string param
devlink: Fix param cmode driverinit for string type
devlink: Fix param set handling for string type
...
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the repeated license text with SDPX identifiers.
While at it bump the Copyright dates for files we touched
this year.
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Nic Viljoen <nick.viljoen@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfp_mutex variable is defined but never used in this file. Not even
in the commit that introduced that variable.
Remove sfp_mutex, it has no purpose.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been reported that since
commit 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
at least RTL_GIGA_MAC_VER_38 NICs work erratically after a resume from
suspend.
The problem has been traced to a missing RX_MULTI_EN bit in the RxConfig
register.
We already set this bit for RTL_GIGA_MAC_VER_35 NICs of the same 8168F
chip family so let's do it also for its other siblings: RTL_GIGA_MAC_VER_36
and RTL_GIGA_MAC_VER_38.
Curiously, the NIC seems to work fine after a system boot without having
this bit set as long as the system isn't suspended and resumed.
Fixes: 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Reported-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tasklet initialisation would be better done by tasklet_init()
instead of assuming all the fields are in an ok state by default.
This does not fix any actual know bug.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 63ae7949e9 ("net: socionext: Use descriptor info instead of MMIO reads on Rx")
removed constant mmio reads from the driver and started using a descriptor
field to check if packet should be processed.
This lead the napi rx handler being constantly called while no packets
needed processing and ksoftirq getting 100% cpu usage. Issue one mmio read
to clear the irq correcty after processing packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During boot, mlx4_core sets the driverinit configuration parameters and
updates the devlink module on the initial values calling
devlink_param_driverinit_value_set().
If devlink_param_driverinit_value_set() returns an error mlx4_core
reports kernel module warning.
This caused false alarm during boot in case kernel was compiled with
CONFIG_NET_DEVLINK off.
Fix by removing warning reported in case
devlink_param_driverinit_value_set() fails.
This actually makes the function mlx4_devlink_set_init_value()
redundant to using directly devlink_param_driverinit_value_set() and so
removed.
It fixes the following kernel trace:
mlx4_core 0000:00:06.0: devlink set parameter 0 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 1 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 4 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 5 value failed (err = -95)
mlx4_core 0000:00:06.0: devlink set parameter 3 value failed (err = -95)
Fixes: bd1b51dc66 ("mlx4: Add mlx4 initial parameters table and register it")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_THERMAL=m, we get a build error:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c: In function 'cxgb4_thermal_get_trip_type':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.c:48:11: error: 'struct adapter' has no member named 'ch_thermal'
Once that is fixed by using IS_ENABLED() checks, we get a link error
against the thermal subsystem when cxgb4 is built-in:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x180): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1e0): undefined reference to `thermal_zone_device_unregister'
Finally, since CONFIG_THERMAL can be =m, the Makefile fails to pick up the
extra file into built-in.a, and we get another link failure against the
cxgb4_thermal_init/cxgb4_thermal_remove files, so the Makefile has to
be adapted as well to work for both CONFIG_THERMAL=y and =m.
Fixes: b187191577 ("cxgb4: Add thermal zone support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant spinlock acquire parameter from ena_com_admin_init()
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improves socket memory utilization when receiving packets larger
than 128 bytes (the previous rx copybreak) and smaller than 256 bytes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Rx refill is done when the number of required descriptors is
above 1/8 queue size. With a default of 1024 entries per queue the
threshold is 128 descriptors.
There is intention to increase the queue size to 8196 entries.
In this case threshold of 1024 descriptors is too large and can hurt
latency.
Add another limitation to Rx threshold to be at most 256 descriptors.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->ip_summed to the correct value as reported by the device.
Add counter for the case where rx csum offload is enabled but
device didn't check it.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes all code changes necessary in ena_netdev to enable
packet sending via the LLQ placemnt mode.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces APIs for detection, initialization, configuration
and actual usage of low latency queues(LLQ). It extends transmit API with
creation of LLQ descriptors in device memory (which include host buffers
descriptors as well as packet header)
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Low Latency Queues(LLQ) allow usage of device's memory for descriptors
and headers. Such queues decrease processing time since data is already
located on the device when driver rings the doorbell.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new fields and definitions to host info and fill them
according to the latest ENA spec version.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce fastpath overhead by making ena_com_tx_comp_req_id_get() inline.
Also move it to ena_eth_com.h file with its dependency function
ena_com_cq_inc_head().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DECAP_ECN0 trap will be used to trap packets where the overlay
packet is marked with Non-ECT, but the underlay packet is marked with
either ECT(0), ECT(1) or CE. When trapped, such packets will be counted
as errors by the VxLAN driver and thus provide better visibility.
The NVE_ENCAP_ARP trap will be used to trap ARP packets undergoing NVE
encapsulation. This is needed in order to support E-VPN ARP suppression,
where the Linux bridge does not flood ARP packets through tunnel ports
in case it can answer the ARP request itself.
Note that all the packets trapped via these traps are marked with
'offload_fwd_mark', so as to not be re-flooded by the Linux bridge
through the ASIC ports.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following resources to be used by the NVE code:
* Number of IPv4 underlay destination IPs in a single TNUMT record
* Number of IPv6 underlay destination IPs in a single TNUMT record
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for setting up the parsing for hash, policy-engine
and routing.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used to program the device with FDB records pointing to a NVE
tunnel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TNQDR register configures the default QoS settings for NVE
encapsulation.
It will be used to set the default DSCP of each port to 0, so that when
DSCP is set to inherit and the overlay packet does not have an IP header
the outer DSCP will be set to 0, in accordance with the software data
path.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register configures how QoS is set in Encapsulation into the
underlay network.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures the actions that are done during NVE
decapsulation based on the ECN bits.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register performs mapping from overlay ECN to underlay ECN during
NVE encapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register builds the linked list of underlay destination IPs used
for BUM traffic on the overlay.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register enables / disables learning on different types of tunnel
ports (e.g., NVE, VPLS).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures global NVE configuration such as source IP of
the NVE tunnel and UDP source port calculation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the seed of the LAG hash function is always set to 0, which
means it is identical across all switches. Instead, use a random number.
This is especially important now that VxLAN is supported, as the LAG
hash function is used to calculate the UDP source port of the
encapsulated packet.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device has the ability to flush all the FDB records that perform NVE
encapsulation or only a subset of these with a specific filtering
identifier (FID).
Expose these types so that they could be used by subsequent patches
where we need to flush the FDB records when an NVE device is unlinked
from a bridge (FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device needs to flood an overlay packet to remote VTEPs it
retrieves a pointer to the head of a linked-list of records that store
the IP addresses of these VTEPs.
These records are stored in the KVD linear memory and configured via the
Tunneling NVE Underlay Multicast Table (TNUMT) register.
Add a new KVD linear entry type for these records, so that we will be
able to allocate and free them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 protocol and address definitions are going to be used by the NVE
code, so move them to the global header file from the one private to the
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VxLAN notifications are going to use a different notifier information
type, so cast to the correct type based on the received event.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VxLAN FDB updates are sent with the VxLAN device which is not our upper
and will therefore be ignored by current code.
Solve this by checking whether the upper device (bridge) is our upper.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VxLAN FDB notifications need to be handled differently than bridge FDB
notifications, so initialize the work item based on the received
notification and rename the invoked function accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spectrum_router.h header file is private to the router block and
should only be included by direct consumers of it, such as dpipe and the
multicast routing code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c: In function 'cgx_fwi_event_handler':
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:257:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
It never be used since introduction in
commit 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the NETIF_F_RXFCS feature in the Mscc
Ethernet driver. This feature is disabled by default and allow a user
to request the driver not to drop the FCS and to extract it into the skb
for debugging purposes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RSS tuple support for VF in revision
0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RSS key, hash algorithm configuration support
for VF in revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ETH_RSS_HASH_XOR hash algorithm supports, which
is supported by hw revision 0x21.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the function __skb_get_hash_symmetric always returns non-zero.
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Wang Li <wangli39@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ethtool .set_coalesce (-C) and .get_coalesce (-c) handlers.
Interrupt moderation is currently not supported, so these accept and
display the default settings of 0 usec and 1 frame.
Toggle tx napi through setting tx-frames. So as to not interfere
with possible future interrupt moderation, value 1 means tx napi while
value 0 means not.
Only allow the switching when device is down for simplicity.
Link: https://patchwork.ozlabs.org/patch/948149/
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the host context count symbols provided by firmware and use
it to determine the number of allocated stats ids. Previously it
won't be possible to offload more than 2^17 filter even if FW was
able to do so.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of an array stats instead of storing stats per flow which
would require a hash lookup at critical times.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of relativistic hash tables for tracking flows instead
of fixed sized hash tables.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several variables being initialized that are being set later
and hence the initialization is redundant and can be removed. Remove
then.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5e netdevice used to calculate fragment edges by a call to
mlx5_wq_cyc_get_frag_size(). This calculation did not give the correct
indication for queues smaller than a PAGE_SIZE, (broken by default on
PowerPC, where PAGE_SIZE == 64KB). Here it is replaced by the correct new
calls/API.
Since (TX/RX) Work Queues buffers are fragmented, here we introduce
changes to the API in core driver, so that it gets a stride index and
returns the index of last stride on same fragment, and an additional
wrapping function that returns the number of physically contiguous
strides that can be written contiguously to the work queue.
This obsoletes the following API functions, and their buggy
usage in EN driver:
* mlx5_wq_cyc_get_frag_size()
* mlx5_wq_cyc_ctr2fragix()
The new API improves modularity and hides the details of such
calculation for mlx5e netdevice and mlx5_ib rdma drivers.
New calculation is also more efficient, and improves performance
as follows:
Packet rate test: pktgen, UDP / IPv4, 64byte, single ring, 8K ring size.
Before: 16,477,619 pps
After: 17,085,793 pps
3.7% improvement
Fixes: 3a2f703312 ("net/mlx5: Use order-0 allocations for all WQ types")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The HW spec defines only bits 24-26 of pftype_wq as the page fault type,
use the required mask to ensure that.
Fixes: d9aaed8387 ("{net,IB}/mlx5: Refactor page fault handling")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allocated memory for context should be freed once
finished working with it.
Fixes: d6c4f0298c ("net/mlx5: Refactor accel IPSec code")
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current design of mlx5e driver ignores the netdevice TX/RX queues
number for netdevices that RDMA IPoIB ULP creates. Instead, the queue
number is initialized to the maximum number that mlx5 thinks best for
performance. As a result, ULP drivers that choose to create a netdevice
with queue number that is less than the maximum channels mlx5 creates,
will get a memory corruption.
This fix changes the mlx5e netdev logic to respect ULP netdevices TX/RX
queue number and use it when creating resources instead of the maximum
channel number.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Convert mlx5e update stats work to a normal work structure, since it is
never used delayed.
Add a helper function to queue update stats work on demand which checks
for some conditions and reduce code duplication to have a better
abstraction.
Fixes: ed56c5193a ("net/mlx5e: Update NIC HW stats on demand only")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move all mlx5e generic structures initializations to mlx5e_netdev_init.
The common structure new initializer function will be used to initialize
mlx5 context for netlink created netdevs such as IPoIB mlx5 accelerated
child netdevs.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
mlx5e_detach_netdev cancels update_stats work which was not initialized
in ipoib netdevice profile, as a result, the following assert occurs:
ODEBUG: assert_init not available (active state 0) object type:
timer_list hint:(null)
This change moves the update stats work to be initialized for all
mlx5e netdevices.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce a helper init/cleanup function that initializes mlx5e generic
netdev private structure, and use them from all profiles init/cleanup
callbacks.
This patch will also be helpful to initialize/cleanup netdevs that are
not created by mlx5 driver, e.g: accelerated ipoib child netdevs.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
netdev has several interfaces that expect to call alloc_netdev_mqs from
the core code, with the driver only providing the arguments. This is
incompatible with the rdma_netdev interface that returns the netdev
directly.
Thus re-organize the API used by ipoib so that the verbs core code calls
alloc_netdev_mqs for the driver. This is done by allowing the drivers to
provide the allocation parameters via a 'get_params' callback and then
initializing an allocated netdev as a second step.
Fixes: cd565b4b51 ("IB/IPoIB: Support acceleration options callbacks")
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Added support in RVU AF driver to register for
CGX LMAC link status change events from firmware
and managing them. Processing part will be added
in followup patches.
- Introduced eventqueue for posting events from cgx lmac.
Queueing mechanism will ensure that events can be posted
and firmware can be acked immediately and hence event
reception and processing are decoupled.
- Events gets added to the queue by notification callback.
Notification callback is expected to be atomic, since it
is called from interrupt context.
- Events are dequeued and processed in a worker thread.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CGX LMAC initialization, link status polling etc is done
by low level secure firmware. For link management this patch
adds a interface or communication mechanism between firmware
and this kernel CGX driver.
- Firmware interface specification is defined in cgx_fw_if.h.
- Support to send/receive commands/events to/form firmware.
- events/commands implemented
* link up
* link down
* reading firmware version
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Nithya Mani <nmani@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each of the enabled CGX LMAC is considered a physical
interface and RVU PFs are mapped to these. VFs of these
SRIOV PFs will be virtual interfaces and share CGX LMAC
along with PF.
This mapping info will be used later on for Rx/Tx pkt steering.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic template for Marvell OcteonTX2's
CGX ethernet interface driver. Just the probe.
RVU AF driver will use APIs exported by this driver
for various things like PF to physical interface mapping,
loopback mode, interface stats etc. Hence marged both
drivers into a single module.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW interprets RVU_AF_MSIXTR_BASE address as an IOVA, hence
create a IOMMU mapping for the physcial address configured by
firmware and reconfig RVU_AF_MSIXTR_BASE with IOVA.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware configures a certain number of MSIX vectors to each of
enabled RVU PF/VF. When a block LF is attached to a PF/VF, number
of MSIX vectors needed by that LF are set aside (out of PF/VF's
total MSIX vectors) and LF's msix_offset is configured in HW.
Also added support for a RVU PF/VF to retrieve that block LF's
MSIX vector offset information from AF via mbox.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for a RVU PF/VF to request AF via mailbox
to attach or detach NPA/NIX/SSO/SSOW/TIM/CPT block LFs.
Also supports partial detachment and modifying current
LF attached count of a certian block type.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scan all RVU blocks to find any 'LF to RVU PF/VF' mapping done by
low level firmware. If found any, mark them as used in respective
block's LF bitmap and also save mapped PF/VF's PF_FUNC info.
This is done to avoid reattaching a block LF to a different RVU PF/VF.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 10's of mailbox messages expected to be handled in future,
checking for message id could become a lengthy switch case. Hence
added a macro to auto generate the switch case for each msg id.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for mailbox interrupt and message
handling. Mapped mailbox region and registered a workqueue
for message handling. Enabled mailbox IRQ of RVU PFs
and registered a interrupt handler. When IRQ is triggered
work is added to the mbox workqueue for msgs to get processed.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mailbox support infrastructure APIs.
Each RVU device has a dedicated 64KB mailbox region
shared with it's peer for communication. RVU AF has
a separate mailbox region shared with each of RVU PFs
and a RVU PF has a separate region shared with each of
it's VF.
These set of APIs are used by this driver (RVU AF) and
other RVU PF/VF drivers eg netdev, crypto e.t.c.
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Lukasz Bartosik <lbartosik@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gathers NPA/NIX/SSO/SSOW/TIM/CPT RVU blocks's
HW info like number of LFs. Important register offsets
saved for later use to avoid code duplication for each block.
A bitmap is allocated for each of the blocks which later
on will be used to allocate a LF for a RVU PF/VF.
Also added RVU NIX/NPA block registers and few registers
of other blocks.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Go through all BLKADDRs and check which ones are implemented
on this silicon and do a HW reset of each implemented block.
Also added all RVU AF and PF register offsets.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic template for Marvell OcteonTX2's
resource virtualization unit (RVU) admin function (AF)
driver. Just the driver registration and probe.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver registers to physical link notifications (of the device)
from Management firmware (MFW). Driver doesn't get notified if there's a
change in the virtual link e.g., link-flap on the peer PF interface.
Virtual link indication from MFW reflects the per PF link status instead
of the physical link.
The patch adds driver support for,
- Advertising the virtual link support to MFW.
- Handling the virtual link notification from MFW.
Please consider applying it to 'net-next'.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When powering down a SDIO connected card during suspend, make sure to call
into the generic lbs_suspend() function before pulling the plug. This will
make sure the card is successfully deregistered from the system to avoid
communication to the card starving out.
Fixes: 7444a80929 ("libertas: fix suspend and resume for SDIO connected cards")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add thermal zone support to monitor ASIC's temperature.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory is limited (on kdump kernel), reduce size of rx and tx rings.
Also reduce the number of rx rings.
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate potential auto casting compilation error.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi poll functions should be initialized before running request_irq(),
to handle a rare condition where there is a pending interrupt, causing
the ISR to fire immediately while the poll function wasn't set yet,
causing a NULL dereference.
Fixes: 1738cd3ed3 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a rare scenario when ena_device_restore() fails, followed by device
remove, an FLR will not be issued. In this case, the device will keep
sending asynchronous AENQ keep-alive events, even after driver removal,
leading to memory corruption.
Fixes: 8c5c7abdeb ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory mapped with devm_ioremap is automatically freed when the driver
is disconnected from the device. Therefore there is no need to
explicitly call devm_iounmap.
Fixes: 0857d92f71 ("net: ena: add missing unmap bars on device removal")
Fixes: 411838e7b4 ("net: ena: fix rare kernel crash when bar memory remap fails")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-10-08
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) sk_lookup_[tcp|udp] and sk_release helpers from Joe Stringer which allow
BPF programs to perform lookups for sockets in a network namespace. This would
allow programs to determine early on in processing whether the stack is
expecting to receive the packet, and perform some action (eg drop,
forward somewhere) based on this information.
2) per-cpu cgroup local storage from Roman Gushchin.
Per-cpu cgroup local storage is very similar to simple cgroup storage
except all the data is per-cpu. The main goal of per-cpu variant is to
implement super fast counters (e.g. packet counters), which don't require
neither lookups, neither atomic operations in a fast path.
The example of these hybrid counters is in selftests/bpf/netcnt_prog.c
3) allow HW offload of programs with BPF-to-BPF function calls from Quentin Monnet
4) support more than 64-byte key/value in HW offloaded BPF maps from Jakub Kicinski
5) rename of libbpf interfaces from Andrey Ignatov.
libbpf is maturing as a library and should follow good practices in
library design and implementation to play well with other libraries.
This patch set brings consistent naming convention to global symbols.
6) relicense libbpf as LGPL-2.1 OR BSD-2-Clause from Alexei Starovoitov
to let Apache2 projects use libbpf
7) various AF_XDP fixes from Björn and Magnus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, both Rx and Tx confirmation frames handled during
NAPI poll were counted toward the NAPI budget. However, Tx
confirmations are lighter to process than Rx frames, which can
skew the amount of work actually done inside one NAPI cycle.
Update the code to only count Rx frames toward the NAPI budget
and set a separate threshold on how many Tx conf frames can be
processed in one poll cycle.
The NAPI poll routine stops when either the budget is consumed
by Rx frames or when Tx confirmation frames reach this threshold.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mscc/ocelot_board.c: In function 'mscc_ocelot_probe':
drivers/net/ethernet/mscc/ocelot_board.c:262:17: warning:
variable 'phy_mode' set but not used [-Wunused-but-set-variable]
enum phy_mode phy_mode;
It never used since introduction in
commit 71e32a20cf ("net: mscc: ocelot: make use of SerDes PHYs for handling their configuration")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.
The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.
The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here, the rc variable is either used only for the condition right after
the assignment or right before being used as the return value of the
function it's being used in.
So let's remove this unneeded temporary variable whenever possible.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`if (x != 0)` is basically a more verbose version of `if (x)` so let's
use the latter so it's consistent throughout the whole driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The == operator precedes the || operator, so we can remove the
parenthesis around (a == b) || (c == d).
The condition is rather explicit and short so removing the parenthesis
definitely does not make it harder to read.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microsemi PHYs (VSC 8530/31/40/41) need to update the Energy Efficient
Ethernet initialization sequence.
In order to avoid certain link state errors that could result in link
drops and packet loss, the physical coding sublayer (PCS) must be
updated with settings related to EEE in order to improve performance.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few counters available in the PHY: receive errors, false
carriers, link disconnects, media CRC errors and valids counters.
So let's expose those in the PHY driver.
Use the priv structure as the next PHY to be supported has a few
additional counters.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Microsemi PHYs have multiple banks of registers (called pages).
Registers can only be accessed from one page, if we need a register from
another page, we need to switch the page and the registers of all other
pages are not accessible anymore.
Basically, to read register 5 from page 0, 1, 2, etc., you do the same
phy_read(phydev, 5); but you need to set the desired page beforehand.
In order to guarantee that two concurrent functions do not change the
page, we need to do some locking per page. This can be achieved with the
use of phy_select_page and phy_restore_page functions but phy_write/read
calls in-between those two functions shall be replaced by their
lock-free alternative __phy_write/read.
Let's migrate this driver to those functions.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix and improve dpaa2-ptp driver
in some places.
- Fixed the return for some functions.
- Replaced kzalloc with devm_kzalloc.
- Removed dev_set_drvdata(dev, NULL).
- Made ptp_dpaa2_caps const.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to removed unused code for dprtc.
This code will be re-added along with more features
of dpaa2-ptp added.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dpaa2-ptp driver, it's odd to use rtc in names of
some functions and structures except these dprtc APIs.
This patch is to use ptp instead of rtc in names.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETDEVICES dependency and ETHERNET dependency hadn't
been required since dpaa2-eth was moved out of staging.
Also allowed COMPILE_TEST for dpaa2-eth.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move DPAA2 PTP driver out of staging/
since the dpaa2-eth had been moved out.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark instructions that use pointers to areas in the stack outside of the
current stack frame, and process them accordingly in mem_op_stack().
This way, we also support BPF-to-BPF calls where the caller passes a
pointer to data in its own stack frame to the callee (typically, when
the caller passes an address to one of its local variables located in
the stack, as an argument).
Thanks to Jakub and Jiong for figuring out how to deal with this case,
I just had to turn their email discussion into this patch.
Suggested-by: Jiong Wang <jiong.wang@netronome.com>
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When pre-processing the instructions, it is trivial to detect what
subprograms are using R6, R7, R8 or R9 as destination registers. If a
subprogram uses none of those, then we do not need to jump to the
subroutines dedicated to saving and restoring callee-saved registers in
its prologue and epilogue.
This patch introduces detection of callee-saved registers in subprograms
and prevents the JIT from adding calls to those subroutines whenever we
can: we save some instructions in the translated program, and some time
at runtime on BPF-to-BPF calls and returns.
If no subprogram needs to save those registers, we can avoid appending
the subroutines at the end of the program.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
On performing a BPF-to-BPF call, we first jump to a subroutine that
pushes callee-saved registers (R6~R9) to the stack, and from there we
goes to the start of the callee next. In order to do so, the caller must
pass to the subroutine the address of the NFP instruction to jump to at
the end of that subroutine. This cannot be reliably implemented when
translated the caller, as we do not always know the start offset of the
callee yet.
This patch implement the required fixup step for passing the start
offset in the callee via the register used by the subroutine to hold its
return address.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Relocation for targets of BPF-to-BPF calls are required at the end of
translation. Update the nfp_fixup_branches() function in that regard.
When checking that the last instruction of each bloc is a branch, we
must account for the length of the instructions required to pop the
return address from the stack.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Offloaded programs using BPF-to-BPF calls use the stack to store the
return address when calling into a subprogram. Callees also need some
space to save eBPF registers R6 to R9. And contrarily to kernel
verifier, we align stack frames on 64 bytes (and not 32). Account for
all this when checking the stack size limit before JIT-ing the program.
This means we have to recompute maximum stack usage for the program, we
cannot get the value from the kernel.
In addition to adapting the checks on stack usage, move them to the
finalize() callback, now that we have it and because such checks are
part of the verification step rather than translation.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is the main patch for the logics of BPF-to-BPF calls in the nfp
driver.
The functions called on BPF_JUMP | BPF_CALL and BPF_JUMP | BPF_EXIT were
used to call helpers and exit from the program, respectively; make them
usable for calling into, or returning from, a BPF subprogram as well.
For all calls, push the return address as well as the callee-saved
registers (R6 to R9) to the stack, and pop them upon returning from the
calls. In order to limit the overhead in terms of instruction number,
this is done through dedicated subroutines. Jumping to the callee
actually consists in jumping to the subroutine, that "returns" to the
callee: this will require some fixup for passing the address in a later
patch. Similarly, returning consists in jumping to the subroutine, which
pops registers and then return directly to the caller (but no fixup is
needed here).
Return to the caller is performed with the RTN instruction newly added
to the JIT.
For the few steps where we need to know what subprogram an instruction
belongs to, the struct nfp_insn_meta is extended with a new subprog_idx
field.
Note that checks on the available stack size, to take into account the
additional requirements associated to BPF-to-BPF calls (storing R6-R9
and return addresses), are added in a later patch.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Similarly to "exit" or "helper call" instructions, BPF-to-BPF calls will
require additional processing before translation starts, in order to
record and mark jump destinations.
We also mark the instructions where each subprogram begins. This will be
used in a following commit to determine where to add prologues for
subprograms.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The checks related to eBPF helper calls are performed each time the nfp
driver meets a BPF_JUMP | BPF_CALL instruction. However, these checks
are not relevant for BPF-to-BPF call (same instruction code, different
value in source register), so just skip the checks for such calls.
While at it, rename the function that runs those checks to make it clear
they apply to _helper_ calls only.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In order to support BPF-to-BPF calls in offloaded programs, the nfp
driver must collect information about the distinct subprograms: namely,
the number of subprograms composing the complete program and the stack
depth of those subprograms. The latter in particular is non-trivial to
collect, so we copy those elements from the kernel verifier via the
newly added post-verification hook. The struct nfp_prog is extended to
store this information. Stack depths are stored in an array of dedicated
structs.
Subprogram start indexes are not collected. Instead, meta instructions
associated to the start of a subprogram will be marked with a flag in a
later patch.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for support for BPF to BPF calls in offloaded programs,
rename the "stack_depth" field of the struct nfp_prog as
"stack_frame_depth". This is to make it clear that the field refers to
the maximum size of the current stack frame (as opposed to the maximum
size of the whole stack memory).
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for BPF-to-BPF calls in offloaded programs, add a new
function attribute to the struct bpf_prog_offload_ops so that drivers
supporting eBPF offload can hook at the end of program verification, and
potentially extract information collected by the verifier.
Implement a minimal callback (returning 0) in the drivers providing the
structs, namely netdevsim and nfp.
This will be useful in the nfp driver, in later commits, to extract the
number of subprograms as well as the stack depth for those subprograms.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We don't really need this state: instead of having an inactive
state where we can awaken zombie queues again if needed, just
keep them in their normal state unless a new queue is actually
needed and there's no other way of getting one.
We do this here by making the inactivity check not free queues
unless instructed that we now really need to allocate one to a
specific station, and in that case it'll just free the queue
immediately, without doing any inactivity step inbetween.
The only downside is a little bit more processing in this case,
but the code complexity is lower.
Additionally, this fixes a corner case: due to the way the code
worked, we could only ever reuse an inactive queue if it was
the reserved queue for a station, as iwl_mvm_find_free_queue()
would never consider returning an inactive queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to call iwl_mvm_inactivity_check() from here in the
next patch, so need to move the code down to be able to.
Fix a minor checkpatch complaint while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The work-queue was used for deferred destruction of hwsim radios;
this does not work well with namespaces about to exit. The one
remaining user has been migrated, so drop the now unused work-queue
instance.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is only used in the file where it's declared,
so just make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of iterating all the queues after having potentially
changed some queue configurations, rechecking if that was done,
mark the ones that do need a TID change explicitly in a bitmap
and use that to send the change to the firmware.
While at it, also rename iwl_mvm_change_queue_owner() to
iwl_mvm_change_queue_tid() since that's more obvious - the
"kind" of owner isn't immediately clear right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We set the queue to this state, only to pretty much immediately
move it out of it again. However, we can't even hit any of the
code that checks if the queue is reconfiguring, because all of
this happens under mvm->mutex and we hold the all the way from
marking the queue as RECONFIGURING to marking it as READY again.
Additionally, the queue that became RECONFIGURING would've been
in SHARED state before, and it can safely stay in that state. In
case of errors, it previously would have stayed in RECONFIGURING
which it could never have left again.
Remove the state entirely and just track the queues that need to
be reconfigured in a separate, local, bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently reconfigure the queues after the inactivity check,
but only in one of the two callers. This might leave queues in
a state where the TID owner is wrong, if called when reserving
a queue for a new station.
Clean this up and do the reconfiguration inside the inactivity
check function. This requires changing the locking, but one of
the two places already holds the mvm mutex and the other easily
can.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If TVQM is used we skip over this, move the code into a new
function to get rid of the label.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to build a bitmap first and then iterate,
just do the iteration with the right locking directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have a hw refcount if we just mark the
command queue with a (fake) TID; at that point, the refcount
becomes equivalent to the hweight() of the TID bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
None of these functions really need to be separate, they're all
only used in sta.c, move them there and make them static.
Fix a small typo in related code while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make this a named struct rather than an anonymous one,
we'll want to refer to it by name later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the rt status checking to the start of the resume flow in order
to avoid sending D0I3_END_CMD to the FW. Also, collect dump if an
assert was encountered.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops. Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.
Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently in case of DCM with P2P GO where BSS DTIM interval < 220 msec
the fw fails to allocate events for the P2P GO dtim due to long passive
scan events.
Fix this by requesting all scans in this scenario to be fragmented with
fast balance scan time settings. The only exception is in case
fragmented scan was planned to be set due to low latency or high
throughput reason, set the scan timing as planned.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fast balance scan is similar to SCAN_TYPE_MILD, but this scan is
fragmented and has shorter out of operating channel time,
and therefore better match low latency scenarios.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split TX tracing to be per TB. This is needed now that
AMSDUs can be sent and skb can be larger than trace
limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we TX AMSDU, we shouldn't pad the packet. In the past,
we were building AMSDU only in transport layer, and gen2
functions are built based on this. However, now that op mode
may build AMSDUs, we need to take care of padding also in
gen2 "non-pcie-amsdu" path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no need to compare *val.vu32* with < 0 because
such variable is of type u32 (32 bits, unsigned), making it
impossible to hold a negative value. Fix this by removing
such comparison.
Also, initialize variable *max_val* to -1, just in case
it is not initialized to either BNXT_MSIX_VEC_MAX or
BNXT_MSIX_VEC_MIN_MAX before using it in a comparison
with val.vu32 at line 159:
if (val.vu32 > max_val)
Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0")
Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbua+lAAoJEG4XJFUm622bc74H/3CU3nKceottcybfmdNcxbTj
OHQ6ulu2OJvIrTnKOIe9WWcgoGeoEEKUcEvrV2SjopYUvFR+XPdC0TPKCxmzi020
QQyemogR+EyMx4nDqYkMysACQjTgzym8vKYrYZ5JAf0S12nRkeu4Qhvod6a9bHkO
HJWJekhm2+wIXOb02LoLhsdijhUUlYPcROZCAXlsYf7mpRIgf7PJQURI+yjfiGBW
Z8cGOH7QHU/68b5ExQAgD3OVpI7cTQ3JlE/IM1nM7UozDPRm7ZipW+Q5XJCYwjfU
Yexh1wo8CUSoK2FW5mwJJUaDUfWR5PQMDBjmGXuauFrfIrTIltJpWliEAIFV++c=
=gsaN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* unify code between mt76x0, mt76x2
* mt76x0 fixes
* another fix for rx buffer allocation regression on usb
* move mt76x2 source files to mt76x2 folder
* more work on mt76x0e support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG/MacGPG2 v2
Comment: GPGTools - http://gpgtools.org
iEYEABECAAYFAlu4h2sACgkQ130UHQKnbvX8wQCgnFzeu4BFVJGROgdilKFwliOx
51wAn28rXRricg0PV1SeLWihSL+ovUZn
=YHTX
-----END PGP SIGNATURE-----
Merge tag 'mt76-for-kvalo-2018-10-05' of https://github.com/nbd168/wireless
mt76 patches for 4.20
* unify code between mt76x0, mt76x2
* mt76x0 fixes
* another fix for rx buffer allocation regression on usb
* move mt76x2 source files to mt76x2 folder
* more work on mt76x0e support
As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.
Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.
The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_txq_build_tfd() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The fall-through to the MVM case is intended as we have to do
*something* to continue, and can't easily clean up. So we'll
just fail in mvm later, if this does happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_gen2_set_tb() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Fixes: ab6c644539 ("iwlwifi: pcie: copy TX functions to new transport")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With NICs that don't read the NVM directly and instead rely on getting
the relevant data from the firmware, the number of reserved MAC
addresses was not added to the API. This caused the driver to assume
there is only one address which results in all interfaces getting the
same address. Update the API to fix this.
While at it, fix-up the comments with firmware api names to actually
match what we have in the firmware.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In mac80211, the default remains for HT, so set the limit to
HE for our driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For SU/SU-ER/MU PPDUs we have spatial reuse.
For those where it's relevant we also know the pre-FEC
padding factor, PE disambiguity bit, beam change bit
and doppler bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add information about the LDCP extra symbol segment to the HE
data when applicable (not for trigger-based PPDUs).
While at it, clean up the code for UL/DL a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This code gets shorter if it doesn't have to check all the
conditions, so move it to an appropriate place that has all
of them validated already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split the code out into a separate routine, and move that to be
called inside the previously introduced iwl_mvm_decode_he_phy_data()
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull some of the decoding of he_phy_data into a separate function so
we don't need to check over and over again if it's valid.
While at it, fix the UL/DL bit reporting to be for all but trigger-
based frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As detected by Luca during code review when I move this in the
next patch, the code here is putting the data into the wrong
field (flags1 instead of flags2). Fix that.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Reported-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove a stray empty line, unbreak some lines that aren't
really that long, and move on variable setting into the
initializer to avoid initializing it twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is equivalent to checking he_phy_data != HE_PHY_DATA_INVAL,
which is already done in a number of places, so remove the extra
'overload' variable entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
queue which means that the worker will not run for now
since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
and that we are now resuming from suspend and cancels
the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
and doesn't really allocate a station ID for the aux
station
17) a new queue is added for the aux station
Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.
Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:
drivers/net/wireless/intel/iwlwifi/pcie/trans.c:2122 iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]()
Timeout waiting for hardware access (CSR_GP_CNTRL 0x080403d8)
Call Trace:
[<ffffffffc03e6ad3>] iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]
[<ffffffffc03e6a13>] iwl_trans_pcie_dump_regs+0x3fd/0x3fd [iwlwifi]
[<ffffffffc03dad42>] iwl_fw_error_dump+0x4f5/0xe8b [iwlwifi]
[<ffffffffc04bd43e>] __iwl_mvm_mac_start+0x5a/0x21a [iwlmvm]
[<ffffffffc04bd6d2>] iwl_mvm_mac_start+0xd4/0x103 [iwlmvm]
[<ffffffffc042d378>] drv_start+0xa1/0xc5 [iwl7000_mac80211]
[<ffffffffc045a339>] ieee80211_reconfig+0x145/0xf50 [mac80211]
[<ffffffffc044788b>] ieee80211_resume+0x62/0x66 [mac80211]
[<ffffffffc0366c5b>] wiphy_resume+0xa9/0xc6 [cfg80211]
The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:
0x00002093 | ADVANCED_SYSASSERT
0x000002F0 | trm_hw_status0
0x00000000 | trm_hw_status1
0x00000B38 | branchlink2
0x0001978C | interruptlink1
0x00000000 | interruptlink2
0xFF080501 | data1
0xDEADBEEF | data2
0xDEADBEEF | data3
Firmware error during reconfiguration - reprobe!
FW error in SYNC CMD SCD_QUEUE_CFG
Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.
Fixes: bf8b286f86 ("iwlwifi: mvm: defer setting IWL_MVM_STATUS_IN_HW_RESTART")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself. Group them in a function to avoid code duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code that dumps various memory types repeats itself. Move it to a
function to avoid duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow the FW to reorder HB channels and first scan HB channels with
assumed APs, in order to reduce the scan duration.
Currently enable it for all scan requests types.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split iwl_fw_error_dump to two parts. The first part will dump the
actual data, and second will do the file allocations, trans calls and
actual file operations. This is done in order to enable reuse of the
code for the new debug ini infrastructure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a macro to replace all the conditions checking for valid dump
length. In addition, move the fifo len calculation to a helper
function.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug variables are bloating the iwl_fw struct. And the fields
are out of order, missing docs and some are redundant.
Clean this up. This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When reading the profiles from the EWRD table in ACPI, we loop over
the data and set it into our internal table. We use the number of
profiles specified in ACPI without checking its validity, so if the
ACPI table is corrupted and the number is larger than our array size,
we will try to make an out-of-bounds access.
Fix this by making sure the value specified in the ACPI table is
valid.
Fixes: 6996490501 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.
The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.
This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the SerDes muxing was hardcoded to a given mode in the MAC
controller driver. Now, the SerDes muxing is configured within the
Device Tree and is enforced in the MAC controller driver so we can have
a lot of different SerDes configurations.
Make use of the SerDes PHYs in the MAC controller to set up the SerDes
according to the SerDes<->switch port mapping and the communication mode
with the Ethernet PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since HSIO address space can be accessed by different drivers, let's
simplify the register address definitions so that it can be easily used
by all drivers and put the register address definition in the
include/soc/mscc/ocelot_hsio.h header file.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since HSIO address space can be used by different drivers (PLL, SerDes
muxing, temperature sensor), let's move it somewhere it can be included
by all drivers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HSIO address space was moved to a syscon, hence we need to get the
regmap of this address space from there and no more from the device
node.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In revision 0x20, we use vlan id != 0 to check whether a vlan tag
has been offloaded, so vlan id 0 is not supported.
In revision 0x21, rx buffer descriptor adds two bits to indicate
whether one or more vlan tags have been offloaded, so vlan id 0
is valid now.
This patch seperates the handle for vlan id 0, add vlan id 0 support
for revision 0x21.
Fixes: 5b5455a9ed ("net: hns3: Add STRP_TAGP field support for hardware revision 0x21")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In revision 0x21, hw supports both ingress and egress vlan filter.
This patch adds support for it.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For mta table support has been dropped, remove the code for mta table.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previously implement for unicast mac vlan table, the space is
shared by all the functions, driver does nothing when the space is
exhausted. This patch preallocates the space of unicast mac vlan
table for each function by software. Each function can only use its
private space and available shared space, avoiding single function
exhausts too much space, and other functions are unable to add
unicast mac address.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, the mac vlan table entries are not cleared when
unload hns3 driver. The dirty mac vlan table entries will make the
result of looking up mac vlan table being unexpected.
When doing core reset or global reset, the firmware will clear all
the tables for driver, and driver shouldn't send any commands to
firmware during reset. But when doing function reset, the driver
needs to clear the tables itself.
This patch clears the mac vlan table entries for each client when
unload driver or reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default mask configuration has been done by firmware, so the driver
doesn't need to do it any more.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In yam_ioctl(), the concrete ioctl command is firstly copied from the
user-space buffer 'ifr->ifr_data' to 'ioctl_cmd' and checked through the
following switch statement. If the command is not as expected, an error
code EINVAL is returned. In the following execution the buffer
'ifr->ifr_data' is copied again in the cases of the switch statement to
specific data structures according to what kind of ioctl command is
requested. However, after the second copy, no re-check is enforced on the
newly-copied command. Given that the buffer 'ifr->ifr_data' is in the user
space, a malicious user can race to change the command between the two
copies. This way, the attacker can inject inconsistent data and cause
undefined behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cxgb_extension_ioctl(), the command of the ioctl is firstly copied from
the user-space buffer 'useraddr' to 'cmd' and checked through the
switch statement. If the command is not as expected, an error code
EOPNOTSUPP is returned. In the following execution, i.e., the cases of the
switch statement, the whole buffer of 'useraddr' is copied again to a
specific data structure, according to what kind of command is requested.
However, after the second copy, there is no re-check on the newly-copied
command. Given that the buffer 'useraddr' is in the user space, a malicious
user can race to change the command between the two copies. By doing so,
the attacker can supply malicious data to the kernel and cause undefined
behavior.
This patch adds a re-check in each case of the switch statement if there is
a second copy in that case, to re-check whether the command obtained in the
second copy is the same as the one in the first copy. If not, an error code
EINVAL is returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mt76x02_irq_handler handler in mt76x02_mmio.c in order to be
reused in mt76x0 driver. Move mt76x02_rx_poll_complete routine in
mt76x02-lib module. Moreover remove pci_core.c and mt76x2/trace.{c,h}
since are empty files
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move tx_tasklet management in mt76x02_mmio.c in order to
be reused by mt76x0 driver and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02_dev data structure as reference in mt76x02_mmio.c
instead of mt76_dev
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx_complete mt76x02-lib module in order to
be reused by mt76x0 drivers for irq unification.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_poll_tx_status in mt76x02_mac.c in order to
be reused by mt76x0 drivers for irq unification.
Moreover introduce mt76x02_trace source file to define mt76x02
trace points
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02u_tx_complete_skb and mt76x02u_remove_dma_hdr since they
are used just by usb code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx_prepare_skb routine in mt76x02-lib module in order
to be reused by mt76x0 driver in tx datapath
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx_get_txpwr_adj and mt76x02_tx_set_txpwr_auto routines
in mt76x02-lib module since they are shared between mt76x0 and mt76x2
drivers. Moreover remove get_txpwr_adj function pointer
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove following function declarations since they have been moved
to mt76x02-lib module:
- mt76x2_sta_add
- mt76x2_sta_remove
- mt76x2_remove_interface
- mt76x2_conf_tx
- mt76x2_txq_init
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rename mt76x02_util.h header file in mt76x02.h since now contains
all mt76x02 related definitions and not just utility routines
declarations
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x02_txrx.c source file in order to contain tx/rx shared
routines for mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx shared routine in mt76x02-lib module and remove
duplicated code. Moreover remove mt76x0/tx.c since it is an empty
file
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Unify rxwi parsing between mt76x2 and mt76x0. Remove the following
routines:
- mt76x0_phy_get_rssi
- mt76x0_queue_rx_skb
- mt76x0_mac_process_rx
Moreover remove mt76x2/common.c and mt76x0/mac.h since are empty files
Enable CCMP PN sw validation
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_process_rx utility routine in mt76x02-lib
in order to by reused by mt76x0 driver for rxwi parsing.
Add stream number check in mt76x02_mac_process_rx since mt76x0
chipsets are 1x1:1
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Merge mt76x0_dev data structure in mt76x02_dev one and remove
duplicated code. Remove unused definition in mt76x0.h.
Moreover merge mt76x0_caldata and mt76x02_rx_freq_cal data structures.
This is a preliminary patch for rxwi unification.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_dev in mt76x02_util.h and rename it in mt76x02_dev
in order to be shared between mt76x2 and mt76x0 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove hw_atomic_mutex mutex in mt76x0_dev data structure
since mt76x0_phy_set_channel is already protected by mt76_dev
mutex while mt76x0_chip_onoff is used just at device probe or
cleanup
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove no longer used mac_lock spinlock and data array
in mt76x0_dev data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use shared mt76x02 utility routines for rssi tracking.
Moreover remove no longer used con_mon_lock spinlock
and following variable:
- ap_bssid
- bcn_freq_off
- bcn_phy_mode
- avg_rssi
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_rx_get_sta and mt76x02_rx_get_sta_wcid utility routines in
mt76x02-lib module since it will be used by mt76x0 driver in order to
unify rxwi parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_phy_get_min_avg_rssi in mt76x02-lib module since
it will be used by mt76x0 driver in order to unify rxwi parsing
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76x02u_tx_prepare_skb routine to fill txwi in mt76x2u and
mt76x0u driver and remove duplicated code. Moreover add static
qualifier to mt76x02_mac_tx_rate_val and mt76x02_mac_fill_txwi
routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_mac_write_txwi in mt76x02_mac.c since it is shared between
mt76x0 and mt76x2 drivers. This is a preliminary patch to unify txwi
configuration between mt76x0 and mt76x2 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add get_tx_txpwr_adj function pointer to mt76_driver_ops data structure
as a preliminary patch to unify txwi configuration between mt76x0 and
mt76x2 drivers since tpc is currently supported just by mt76x2 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02_tx_get_max_txpwr_adj routine in mt76x02-lib module
since now both mt76x0 and mt76x2 drivers read rate tx power gain from
rate_power data structure. Moreover remove get_max_txpwr_adj function
pointer from mt76_driver_ops data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stop mac and calibration work stopping the hw even if the
device has been removed
Fixes: b11e19694d ("mt76x0: add ieee80211_ops ops pointer to
mt76x0_alloc_device signature")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76u_alloc_queues need to be called before mt76u_mcu_init_rx
since it initializes rx_page_lock spinlock used in mt76u_buf_alloc
routine.
Fixes: b11e19694d ("mt76x0: add ieee80211_ops ops pointer to
mt76x0_alloc_device signature")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is correct fix for c12128ce44 ("mt76: use a per rx queue page
fragment cache"). We use wrong length when we allocate segments for
MCU transmissions, which require bigger segment size than e->buf_size.
Commit 481bb04324 ("mt76: usb: make rx page_frag_cache access atomic")
partially solved the problem or actually mask it by changing
mt76u_mcu_init_rx() and mt76u_alloc_queues() sequence, so e->buf_size
become non zero any longer, but still not big enough to handle MCU data.
Patch fixes memory corruption which can manifest itself as random,
not easy to reproduce crashes, during mt76 driver load or unload.
Fixes: c12128ce44 ("mt76: use a per rx queue page fragment cache")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The header guards that are #defined are different from those being
checked. Fix this by #defining them to the correct name.
Fixes clang warnings:
drivers/net/wireless/mediatek/mt76/mt76x02_mcu.h:17:9:
warning: '__MT76x02_MCU_H' is used as a header guard here, followed
by #define of a different macro [-Wheader-guard]
drivers/net/wireless/mediatek/mt76/mt76x02_usb.h:17:9:
warning: '__MT76x02_USB_H' is used as a header guard here, followed
by #define of a different macro [-Wheader-guard]
Fixes: 905db74701 ("mt76: usb: move mt76x02 mcu code in mt76x02-usb module")
Fixes: edaa580bc8 ("mt76: move shared mcu_calibrate routine in mt76x02-lib module")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2 and mt76x2u drivers to mt76x2 subfolder and
leave just shared code in mt76 root folder
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0e_cleanup routine to tidy up the device
during device removal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
when 32 bit port capability is in use, use FW_PORT_ACTION_L1_CFG32
rather than FW_PORT_ACTION_L1_CFG.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of dump_station cfg80211 callback supports
AP mode only. Add support for STA mode as well: by default in STA
mode this callback is supposed to return AP on managed interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Command responses and events from the firmware are copied twice in
control path: at first in shm core (qtnf_shm_handle_new_data) and
then in pcie bus drivers (qtnf_pcie_control_rx_callback). There
is no need to copy this data twice, it can be done only once
in rx callbacks.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Notify firmware to flush cache before scanning when needed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SGI should be passed to wireless core as a part of rate structure.
Otherwise wireless core performs incorrect rate calculation when
SGI is enabled in hardware but not reported to host.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not cancel scan in disconnect callback. If there is an active scan,
it will be cancelled by firmware, then host driver will be properly
notified by event.
Cancelling scan in disconnect callback occasionally may lead to the
following race issue. Host is able to queue one scan after scan
abort in disconnect callback, and another scan after scan abort
in event handler. As a result, firmware receives second scan
before the first scan completes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unify command error handling using qtnf_cmd_resp_result_decode
function. Do not duplicate error messages in command handlers
and cfg80211 callbacks: report 'cmd exec fail' only on control
path internal failure. Remove redundant 'unlikely' macros.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several members of pwr-MAC structure are re-initialized several times
together with per-VIF initialization. Fix that and simplify the code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When cfg80211 disconnect callback is triggered and command is
processed by firmware, disconnect event with local parameter
set must be sent immediately. Indicating that it's a "local"
event (not from AP) will help upper layers to process this
event correctly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove STA connection states tracking from driver.
Leave it wireless core on host and to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/b43/main.c: In function 'b43_one_core_detach':
drivers/net/wireless/broadcom/b43/main.c:5496:17: warning:
variable 'wl' set but not used [-Wunused-but-set-variable]
After commit 644aa4d620 ("b43: remove list of IEEE 802.11 devices")
'wl' is not used any more.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
lockdep_assert_held() is better suited to checking locking requirements,
since it won't get confused when someone else holds the lock. This is
also a step towards possibly removing spin_is_locked().
Signed-off-by: Lance Roy <ldr709@gmail.com>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now with wlcore using PM runtime, we can also add support for Linux
generic wakeirq handling for it if configured in the dts file.
The wakeirq can be configured as the second interrupt in the dts file
with interrupts-extended property where it is the padconf irq of the OOB
GPIO pin used for wlcore interrupt.
Note that eventually we should also allow configuring wlcore to use the
SDIO dat1 IRQ for wake-up, and in that case the the wakeirq should be
configured to be the padconf interrupt of the dat1 pin and not the
padconf interrupt of the OOB GPIO pin.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not currently clear wl->elp_compl on ELP timeout and we have bogus
lingering pointer that wlcore_irq then will try to access after recovery
is done:
BUG: spinlock bad magic on CPU#1, irq/255-wl12xx/580
...
(spin_dump) from [<c01b9344>] (do_raw_spin_lock+0xc8/0x124)
(do_raw_spin_lock) from [<c09b3970>] (_raw_spin_lock_irqsave+0x68/0x74)
(_raw_spin_lock_irqsave) from [<c01a02f0>] (complete+0x24/0x58)
(complete) from [<bf572610>] (wlcore_irq+0x48/0x17c [wlcore])
(wlcore_irq [wlcore]) from [<c01c5efc>] (irq_thread_fn+0x2c/0x64)
(irq_thread_fn) from [<c01c623c>] (irq_thread+0x148/0x290)
(irq_thread) from [<c016b4b0>] (kthread+0x160/0x17c)
(kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
...
After that the system will hang. Let's fix this by adding a flag for
recovery and moving the recovery work call to to the error handling
section.
And we want to set WL1271_FLAG_INTENDED_FW_RECOVERY and actually clear
it too in wl1271_recovery_work() and just downgrade the error to a
warning to prevent overly verbose output.
Cc: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following:
bool efuse_re_pg_sec1flag;
u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.
This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.
Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().
This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
the be2net implementation of .ndo_tunnel_{add,del}() changes the value of
NETIF_F_GSO_UDP_TUNNEL bit in 'features' and 'hw_features', but it forgets
to call netdev_features_change(). Moreover, ethtool setting for that bit
can potentially be reverted after a tunnel is added or removed.
GSO already does software segmentation when 'hw_enc_features' is 0, even
if VXLAN offload is turned on. In addition, commit 096de2f83e ("benet:
stricter vxlan offloading check in be_features_check") avoids hardware
segmentation of non-VXLAN tunneled packets, or VXLAN packets having wrong
destination port. So, it's safe to avoid flipping the above feature on
addition/deletion of VXLAN tunnels.
Fixes: 630f4b7056 ("be2net: Export tunnel offloads only when a VxLAN tunnel is created")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c499696e79 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e79 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting the max rings supported, get the reduced max_irqs
by the ones used by RDMA.
If the number MSIX is the limiting factor, this bug may cause the
max ring count to be higher than it should be when RDMA driver is
loaded and may result in ring allocation failures.
Fixes: 30f529473e ("bnxt_en: Do not modify max IRQ count after RDMA driver requests/frees IRQs.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.
This patch fixes the problem described above.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In HWRM_QUEUE_COS2BW_CFG request, enables field should have the bits
set only for the queue ids which are having the valid parameters.
This causes firmware to return error when the TC to hardware CoS queue
mapping is not 1:1 during DCBNL ETS setup.
Fixes: 2e8ef77ee0 ("bnxt_en: Add TC to hardware QoS queue mapping logic.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enables bit for VNIC was set wrong when calling the HWRM_FUNC_CFG
firmware call to reserve VNICs. This has the effect that the firmware
will keep a large number of VNICs for the PF, and having very few for
VFs. DPDK driver running on the VFs, which requires more VNICs, may not
work properly as a result.
Fixes: 674f50a5b0 ("bnxt_en: Implement new method to reserve rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Michal remaind, we should allow to clear ttl inherit. Then we will
have three states:
1. set the flag, and do ttl inherit.
2. do not set the flag, use configured ttl value, or default ttl (0) if
not set.
3. disable ttl inherit, use previous configured ttl value, or default ttl (0).
Fixes: 52d0d404d3 ("geneve: add ttl inherit support")
CC: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
process_one_work+0x18d/0x2fc
worker_thread+0x1a2/0x269
? pr_cont_work+0x58/0x58
kthread+0xfa/0x10a
? pr_cont_work+0x58/0x58
? rcu_read_unlock_sched_notrace+0x48/0x48
ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
