This fixes false radar detection (of radar type 7)
in Japan region by correcting the radar pulse type
to Chirp as per specification.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added per tid sta counters for the following
- Total number MSDUs received from firmware
- Number of MSDUs received with errors like decryption, crc, mic ,etc.
- Number of MSDUs dropped in the driver
- A-MPDU/A-MSDU subframe stats
- Number of MSDUS passed to mac80211
All stats other than A-MPDU stats are only for received data frames.
A-MPDU stats might have stats for management frames when monitor
interface is active where management frames are notified both in wmi
and HTT interfaces.
These per tid stats can be enabled with tid bitmask through a debugfs
like below
echo <tid_bitmask> > /sys/kernel/debug/ieee80211/phyX/ath10k/sta_tid_stats_mask
tid 16 (tid_bitmask 0x10000) is used for non-qos data/management frames
The stats are read from
/sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/<sta_mac>/dump_tid_stats
Sample output:
To enable rx stats for tid 0, 5 and 6,
echo 0x00000061 > /sys/kernel/debug/ieee80211/phy0/ath10k/sta_tid_stats_mask
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan15/stations/8c\:fd\:f0\:0a\:8e\:df/dump_tid_stats
Driver Rx pkt stats per tid, ([tid] count)
------------------------------------------
MSDUs from FW [00] 2567 [05] 3178 [06] 1089
MSDUs unchained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:chained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:filtered [00] 0 [05] 0 [06] 0
MSDUs queued for mac80211 [00] 2567 [05] 3178 [06] 1089
MSDUs with error:fcs_err [00] 0 [05] 0 [06] 2
MSDUs with error:tkip_err [00] 0 [05] 0 [06] 0
MSDUs with error:crypt_err [00] 0 [05] 0 [06] 0
MSDUs with error:peer_idx_inval [00] 0 [05] 0 [06] 0
A-MPDU num subframes upto 10 [00] 2567 [05] 3178 [06] 1087
A-MPDU num subframes 11-20 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 21-30 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 31-40 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 41-50 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 51-60 [00] 0 [05] 0 [06] 0
A-MPDU num subframes >60 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 1 [00] 2567 [05] 3178 [06] 1089
A-MSDU num subframes 2 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 3 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 4 [00] 0 [05] 0 [06] 0
A-MSDU num subframes >4 [00] 0 [05] 0 [06] 0
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some functions definitions have either the initial open brace and/or
the closing brace outside of column 1.
Move those braces to column 1.
This allows various function analyzers like gnu complexity to work
properly for these modified functions.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fixes for 4.16, only for iwlwifi and brcmfmac this time. All
pretty small.
iwlwifi
* fix an issue with the multicast queue
* fix IGTK handling
* fix some missing return value checks
* add support for a HW workaround for issues on some platforms
* a couple of fixes for channel-switch
* a few fixes for the aggregation handling code
brcmfmac
* drop Inter-Access Point Protocol packets by default
* fix check for ISO3166 regulatory code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatiw3AAoJEG4XJFUm622bU7IH/0sIrhxJw+RJhTFQhRIx+WdN
XPWCb1bUXMwb3+4a+Z3cPuLsKHsv4TJTXtglSvZtihpasr6zALNeoZCb6md5mHz8
lLRWmMsyPQqnVy7mC7CO7qY5u8M6cZFvJgmn3pU8TAcok2r0skFiKCjqhY6A5ZUM
V6dlmjld08i5Y8xGlFPFQwCK9NFNoe2YK5k7U5GeY+0PXK9koT7H7amXcYSnU+Nl
Vrv/MZCGsOYa5E93IhPYkGRBasKqnLcS8+Rf+0zJl1eZuumyMr1+eqgaF1gVRC8w
rTvGyHUMv5OXxw6UHItHlQbW+Wgypdo1qRCfsxsAWOj6W5L1uj258CgSiMcwp1o=
=YWna
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.16
Some fixes for 4.16, only for iwlwifi and brcmfmac this time. All
pretty small.
iwlwifi
* fix an issue with the multicast queue
* fix IGTK handling
* fix some missing return value checks
* add support for a HW workaround for issues on some platforms
* a couple of fixes for channel-switch
* a few fixes for the aggregation handling code
brcmfmac
* drop Inter-Access Point Protocol packets by default
* fix check for ISO3166 regulatory code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
request_firmware_cache() will ensure the firmware is available on resume
from suspend if on reboot the device retains the firmware.
This optimization is in place given otherwise on reboot we have to
reload the firmware, the opmization saves us about max 1s, minimum 10ms.
Cantabile has reported back this fixes his woes with both suspend and
hibernation.
Reported-by: Cantabile <cantabile.desu@gmail.com>
Tested-by: Cantabile <cantabile.desu@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When switching mac80211 to use QoS NDP, it turned out that
ath9k_htc is somehow broken by this, e.g. see
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060.
Fix this by using the new mac80211 flag to go back to the
old, incorrect, behaviour for this driver.
Fixes: 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing")
Reported-by: Ben Caradoc-Davies <ben@transient.nz>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the wmediumd to the net's wmediumd when the radio gets created.
Radios created after HWSIM_CMD_REGISTER don't currently get their
data->wmediumd set and the userspace would need to reconnect to
netlink to be able to call HWSIM_CMD_REGISTER again.
Alternatively I think data->netgroup and data->wmedium could be
replaced with a pointer to hwsim_net.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When destroying a net namespace, all hwsim interfaces, which are not
created in default namespace are deleted. But the async deletion of the
interfaces could last longer than the actual destruction of the
namespace, which results to an use after free bug. Therefore use
synchronous deletion in this case.
Fixes: 100cb9ff40 ("mac80211_hwsim: Allow managing radios from non-initial namespaces")
Reported-by: syzbot+70ce058e01259de7bb1d@syzkaller.appspotmail.com
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
OR'ing in 0x40 before a memcpy() to overwrite the value doesn't
do much good - flip the order of operations are reported and
tested by Jouni.
Fixes: cb1a5bae56 ("mac80211_hwsim: add permanent mac address option for new radios")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit "regulatory: add NUL to request alpha2" increases the length of
alpha2 to 3. This causes a regression on brcmfmac, because
brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete
array. So fix this accordingly.
Fixes: 657308f73e ("regulatory: add NUL to request alpha2")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When immediate quiet bit is set in CSA, the entire channel is blocked
by the firmware. It is expected that all the MACs will evacuate the
channel and the phy will be eventually either moved or removed.
Currently, the phy context is just unreferenced and thus, the quiet
bit is kept set and it will be impossible to TX on this phy, if we
will need to reuse it in the future. This can be seen when doing a
channel switch with mode=1 (quiet) twice from channel X to Y and then
back to channel X.
Fix that, by moving the phy context to a default channel when not
referenced anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.
While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.
Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a queue is reserved for aggregation, the queue id is assigned
to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper()
takes care of allocating the queue before actual tx starts.
When the reservation is cancelled (e.g. when the AP declined the
aggregation request) the tid_data is not cleared. As a result,
following tx for this tid was trying to use an unallocated queue.
Fix this by setting the txq_id for the tid to invalid when unreserving
the queue.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.
Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Testing brcmfmac with more recent firmwares resulted in AP interfaces
not working in some specific setups. Debugging resulted in discovering
support for IAPP in Broadcom's firmwares.
Older firmwares were only generating 802.11f frames. Newer ones like:
1) 10.10 (TOB) (r663589)
2) 10.10.122.20 (r683106)
for 4366b1 and 4366c0 respectively seem to also /respect/ 802.11f frames
in the Tx path by performing a STA disassociation.
This obsoleted standard and its implementation is something that:
1) Most people don't need / want to use
2) Can allow local DoS attacks
3) Breaks AP interfaces in some specific bridge setups
To solve issues it can cause this commit modifies brcmfmac to drop IAPP
packets. If affects:
1) Rx path: driver won't be sending these unwanted packets up.
2) Tx path: driver will reject packets that would trigger STA
disassociation perfromed by a firmware (possible local DoS attack).
It appears there are some Broadcom's clients/users who care about this
feature despite the drawbacks. They can switch it on using a new module
param.
This change results in only two more comparisons (check for module param
and check for Ethernet packet length) for 99.9% of packets. Its overhead
should be very minimal.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations. We need to set a bit in the phy
configuration to indicate that to the FW. To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware. And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.
Fixes: c62446d2b0 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.
Found by smatch:
.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.
The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.
To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.
Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
skb_copy_expand without __GFP_NOWARN already does a dump_stack
on OOM so these messages are redundant.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ath9k was switched over to use the mac80211 intermediate queues,
node cleanup now drains the mac80211 queues. However, this call path is
not protected by rcu_read_lock() as it was previously entirely internal
to the driver which uses its own locking.
This leads to a possible rcu_dereference() without holding
rcu_read_lock(); but only if a station is cleaned up while having
packets queued on the TXQ. Fix this by adding the rcu_read_lock() to the
caller in ath9k.
Fixes: 50f08edf98 ("ath9k: Switch to using mac80211 intermediate software queues.")
Cc: stable@vger.kernel.org
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends mgmt frames by reference via WMI.
The host dma maps the mgmt frame and sends the physical
address to the firmware in the wmi command. Since the
dma mapping is done in the gen_mgmt_tx and if the wmi
command send fails, the corresponding mgmt frame is
not being dma unmapped.
Fix the missing dma unmapping of mgmt tx frame when
wmi command sending fails for mgmt tx by reference
via WMI. The already exisiting mgmt tx using copy by
value does not need such dma unmapping.
Add a separate wmi-tlv op for mgmt tx via ref, which
takes care of unmapping the dma address, in case of
wmi command sending failure.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At present driver gets chan_type by referring to
IEEE80211_HT_PARAM_CHA_SEC_OFFSET, in ASSOC response. Sometimes
AP shows IEEE80211_HT_PARAM_CHA_SEC_OFFSET as above/below in
assoc response, even if the association is done on HT20 channel
only. So, it will be accurate to get econdary channel offset from
firmware.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IEEE80211_CHAN_NO_HT40PLUS and IEEE80211_CHAN_NO_HT40PLUS channel
flags tell if HT40 operation is allowed on a channel or not.
This patch ensures ht_capability information is modified
accordingly so that we don't end up creating a HT40 connection
when it's not allowed for current regulatory domain.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit bcc920e8f0.
Drivers gets hardware info and updates ht_cap field of
wiphy->bands during initialization. Once updated during init,
ht_cap must not be modified as it reflects the capability
supported by hardwawre. Above patch tries to modify the ht_cap
field and this results in wrongly advertising capabilities during
association.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
High bits of antenna number are reserved in hardware spec,
using low 4 bits represent supported antenna.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lots of the wireless driver vendor Kconfig symol help text says
"questions about cards." (2 spaces between "about" and "cards")
Besides dropping one of those spaces, it also needs some other word
inserted there. Instead of putting each vendor's name there, I chose
to say "these" cards in all of the Kconfig help text.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Curretly, RX packet processing is done sequencially. To improve
the efficiency, RX skb queue is introduced.
Here, while preparing RX URB skb is allocated and used
for RX buffer. When rx done handler is called, enqueue the skb
to rx_q and set the thread event.
RX thread is modified to dequeue packets from skb queue and
process further.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently 2 RX control blocks are allocated by default.
If wifi alone mode is used rx control block 2 is unusable.
So, changes are done accordingly in all places to use
RX control blocks dynamically based on coex mode check.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, RX packets are handled in interrupt context in SDIO
interface. To improve the efficiency of processing RX packets,
RX thread and RX skb queues are introduced.
When the packet is read from device, driver prepares skb, add to
RX queue and trigger RX thread event. RX thread processes the
packets from RX queue.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Queue number is correctly updated for BT traffic. Also, kzalloc
instead of kmalloc is used for Rx packet allocation.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Operating mode determines the support for other protocols.
This is made as module parameter for better usage.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BT frames are passed through coex and hal modules to BUS.
After firmware is loaded, based on the operating mode CARD
READY frame comes for each protocol. When BT card ready is
received, BT attach is called.
Protocol operations are exchanged between the modules
at initialization time.
Build flag CONFIG_RSI_COEX is introduced to enable coex support
if CONFIG_BT_RSIHCI is enabled. Coex operations are valid if
coex mode is greater than 1 only.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With BT support, driver has to handle two streams of data
(i.e. wlan and BT). Actual coex implementation is in firmware.
Coex module just schedule the packets to firmware by taking them
from the corresponding paths.
Structures for module and protocol operations are introduced for
this purpose. Protocol operations structure is global structure
which can be shared among different modules. Move initialization
of coex and operating mode values to rsi_91x_init().
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The common parameters used by wlan and bt modules are add
to a new header file "rsi_91x.h" defined in 'include/net'
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx bluetooth endpoint shall be added in further patches. Rx control
block is introduced here to handle Rx packets properly. Separate
function is written to initialize the RX control blocks.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Apparently the hardware does not perform CCMP PN validation so
let mac80211 take care of possible replay attacks in sw.
Moreover indicate ICV and MIC had been stripped setting corresponding
bits in ieee80211_rx_status.
The fix has been validated using 4.2.1 and 4.1.3 tests from the WiFi
Alliance vulnerability detection tool.
Fixes: c869f77d6a ("add mt7601u driver")
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: David Park <david.park@hitemengineering.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove mt7601u_dev parameter from mt7601u_mcu_msg_alloc signature since
dev pointer is never used in routine body
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Substitute unnecessary len variable in mt76x2_eeprom_load() with
MT7662_EEPROM_SIZE macro since len is used just to store eeprom
default size.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the following sparse warning in mt7601u_efuse_physical_size_check:
- drivers/net/wireless/mediatek/mt7601u/eeprom.c:77:27: warning:
Variable length array is used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add capability to select tx/rx antennas. Possible values are:
- 1: to use only the first antenna
- 2: to use only the second antenna
- 3: to use both of them
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76_init_stream_cap utility routine to set ht/vht sta capabilities
related to number of streams currently used by the device
(it will be used by mac80211 set_antenna callback)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize available_antennas related info in wiphy data structure
according to antenna_mask field; antenna_mask info is initialized
in device specific code and will be used in mac80211 {set,get}_antenna
callbacks
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.
iwlwifi
* fix a bogus warning when freeing a TFD
* fix severe throughput problem with 9000 series
* fix for a bug that caused queue hangs in certain situations
* fix for an issue with IBSS
* fix an issue with rate-scaling in AP-mode
* fix Channel Switch Announcement (CSA) issues with count 0 and 1
* some firmware debugging fixes
* remov a wrong error message when removing keys
* fix a firmware sysassert most usually triggered in IBSS
* a couple of fixes on multicast queues
* a fix with CCMP 256
rtlwifi
* fix loss of signal for rtl8723be
brcmfmac
* add possibility to obtain firmware error
* fix P2P_DEVICE ethernet address generation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaoVCFAAoJEG4XJFUm622bRiQIAKJ9HmZQwda8Y7Ypj/y2YIJr
Rqmd+PSjfD+FNT33Ue+x/LPCfM2SnFQdnL61kqOSIgOCDS+uwwe8mDVa+DtaT+Dd
sU5ftjVjBXuYiqs2XW0n8dPszFftc7omCNVAeAJcBISqrqKkXUi3Bg47jK02kV6E
AAGvyJwxIMr187nFaC8N55cas0At7Mbbsvh0YRNjxnoqKOmC3NpJZPskv3C/gvUs
ADJkFPUwImqE9+BwoEguAGcqV8hLVVnoXf87Ro4L1SrFl11gJSiifq/FqwXHXm8E
YyJNo6lGdaw5uuX2T9wW6QfBghMoncE/tmwgLKdLyjyV8H2c6iEMKMygZIN0eTI=
=HvdQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo:
====================
wireless-drivers fixes for 4.16
Quote a few fixes as I have not been able to send a pull request
earlier. Most of the fixes for iwlwifi but also few others, nothing
really standing out though.
iwlwifi
* fix a bogus warning when freeing a TFD
* fix severe throughput problem with 9000 series
* fix for a bug that caused queue hangs in certain situations
* fix for an issue with IBSS
* fix an issue with rate-scaling in AP-mode
* fix Channel Switch Announcement (CSA) issues with count 0 and 1
* some firmware debugging fixes
* remov a wrong error message when removing keys
* fix a firmware sysassert most usually triggered in IBSS
* a couple of fixes on multicast queues
* a fix with CCMP 256
rtlwifi
* fix loss of signal for rtl8723be
brcmfmac
* add possibility to obtain firmware error
* fix P2P_DEVICE ethernet address generation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware has a requirement that the P2P_DEVICE address should
be different from the address of the primary interface. When not
specified by user-space, the driver generates the MAC address for
the P2P_DEVICE interface using the MAC address of the primary
interface and setting the locally administered bit. However, the MAC
address of the primary interface may already have that bit set causing
the creation of the P2P_DEVICE interface to fail with -EBUSY. Fix this
by using a random address instead to determine the P2P_DEVICE address.
Cc: stable@vger.kernel.org # 3.10.y
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The feature module needs to evaluate the actual firmware error return
upon a control command. This adds a flag to struct brcmf_if that the
caller can set. This flag is checked to determine the error code that
needs to be returned.
Fixes: b69c1df472 ("brcmfmac: separate firmware errors from i/o errors")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These pernet_operations allocate and destroy IDA identifier,
and these actions are synchronized by IDA subsystem locks.
Exit method removes mac80211_hwsim_data enteries from the lists,
and this is synchronized by hwsim_radio_lock with the rest
parallel pernet_operations. Also it queues destroy_radio()
work, and these work already may be executed in parallel
with any pernet_operations (as it's a work :). So, we may
mark these pernet_operations as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
hwsim_netgroup counter is declarated as int, and it is incremented
every time a new net is created. After sizeof(int) net are created,
it will overflow, and different net namespaces will have the same
identifier. This patch fixes the problem by introducing IDA instead
of int counter. IDA guarantees, all the net namespaces have the uniq
identifier.
Note, that after we do ida_simple_remove() in hwsim_exit_net(),
and we destroy the ID, later there may be executed destroy_radio()
from the workqueue. But destroy_radio() does not use the ID, so it's OK.
Out of bounds of this patch, just as a report to wireless subsystem
maintainer, destroy_radio() increaments hwsim_radios_generation
without hwsim_radio_lock, so this may need one more patch to fix.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
'default false' should be 'default n', though they happen to have the
same effect here, due to undefined symbols ('false' in this case)
evaluating to n in a tristate sense.
Remove the default instead of changing it. bool and tristate symbols
implicitly default to n.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the scheduler config command, the meaning of tid == 0xf was intended
to indicate the configuration is for management frames. However,
tid == 0xf was also used for the multicast queue that was meant only
for multicast data frames, which resulted with the FW not encrypting
multicast data frames.
As multicast frames do not have a QoS header, fix this by setting
tid == 0, to indicate that this is a data queue and not management
one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Multicast frames for NL80211_IFTYPE_AP and NL80211_IFTYPE_ADHOC were
directed to the broadcast station, however, as the broadcast station
did not have keys configured, these frames were sent unencrypted.
Fix this by using the multicast station which is the station for which
encryption keys are configured.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the GTK is installed, we install it to HW with the
station ID of the AP.
Mac80211 will try to remove it only after the AP sta is
removed, which will result in a failure to remove key
since we do not have any station for it.
This is a valid situation, but a previous commit removed
the early return and added a return with error value, which
resulted in an error message that is confusing to users.
Remove the error return value.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trying to collect firmware debug data while firmware
is not loaded causes various errors (e.g. failing NIC access).
This causes even a bigger issue if at that time the
HW radio is off.
In that case, when later turning the radio on, the Driver
fails to read the HW (registers contain garbage values).
(It may be that the CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN
bit is cleared on faulty NIC access - since the same behavior
was seen in HW RFKILL toggling before setting that bit.)
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We should add the multicast station before adding the
broadcast station.
However, in older FW, the firmware will start beaconing
when we add the multicast station, and since the broadcast
station is not added at this point so the transmission
of the beacon will fail on assert 0x2b00.
This is fixed in later firmware, so make the order
of addition depend on the TLV.
Fixes: 26d6c16bed ("iwlwifi: mvm: add multicast station")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It was assumed that apply_time==0 implies immediate scheduling, which is
wrong. Instead, the fw expects the START_IMMEDIATELY flag to be set.
Otherwise, this resulted in 0x3063 assert.
Fix that.
While at it rename the T2_V2_START_IMMEDIATELY to
TE_V2_START_IMMEDIATELY.
Fixes: f5d8f50f27 ("iwlwifi: mvm: Fix channel switch in case of count <= 1")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't have enough room in the TX command for a CCMP 256
key, and need to use key from table.
Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While entering to D3 mode there is a gap between the time the
driver handles the D3_CONFIG_CMD response to the time the host is going
to sleep.
In between there might be cases which MARKER_CMD can tailgate.
Also during resume flow the MARKER_CMD might get sent while D0I3_CMD
is being handled in the FW.
Cancel MARKER_CMD timer and set it again properly during suspend
resume flows to prevent this command from being sent accidentlly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Introduce __mt7601u_rr and __mt7601u_vendor_single_wr routines in order
to make mt7601u_rmw and mt7601u_rmc atomic. This patch does not fix a
reported issue but makes the usb access more robust to concurrent
operations on the same register since it is theoretically possible that
read and write accesses of mt7601u_rmw/mt7601u_rmc can be interleaved with
a different write operation on the same register.
Moreover using __mt7601u_rr and __mt7601u_vendor_single_wr in
mt7601u_rmw/mt7601u_rmc allows to grab vendor_req_mutex mutex once
instead of twice
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be reproduced by bind/unbind the driver multiple times
in AM3517 board.
Analysis revealed that rtl8187_start() was invoked before probe
finishes(ie. before the mutex is initialized).
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
[<c010e0d8>] (unwind_backtrace) from [<c010beac>] (show_stack+0x10/0x14)
[<c010beac>] (show_stack) from [<c017401c>] (register_lock_class+0x4f4/0x55c)
[<c017401c>] (register_lock_class) from [<c0176fe0>] (__lock_acquire+0x74/0x1938)
[<c0176fe0>] (__lock_acquire) from [<c0178cfc>] (lock_acquire+0xfc/0x23c)
[<c0178cfc>] (lock_acquire) from [<c08aa2f8>] (mutex_lock_nested+0x50/0x3b0)
[<c08aa2f8>] (mutex_lock_nested) from [<c05f5bf8>] (rtl8187_start+0x2c/0xd54)
[<c05f5bf8>] (rtl8187_start) from [<c082dea0>] (drv_start+0xa8/0x320)
[<c082dea0>] (drv_start) from [<c084d1d4>] (ieee80211_do_open+0x2bc/0x8e4)
[<c084d1d4>] (ieee80211_do_open) from [<c069be94>] (__dev_open+0xb8/0x120)
[<c069be94>] (__dev_open) from [<c069c11c>] (__dev_change_flags+0x88/0x14c)
[<c069c11c>] (__dev_change_flags) from [<c069c1f8>] (dev_change_flags+0x18/0x48)
[<c069c1f8>] (dev_change_flags) from [<c0710b08>] (devinet_ioctl+0x738/0x840)
[<c0710b08>] (devinet_ioctl) from [<c067925c>] (sock_ioctl+0x164/0x2f4)
[<c067925c>] (sock_ioctl) from [<c02883f8>] (do_vfs_ioctl+0x8c/0x9d0)
[<c02883f8>] (do_vfs_ioctl) from [<c0288da8>] (SyS_ioctl+0x6c/0x7c)
[<c0288da8>] (SyS_ioctl) from [<c0107760>] (ret_fast_syscall+0x0/0x1c)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = cd1ec000
[00000000] *pgd=8d1de831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
task: ce73eec0 task.stack: cd1ea000
PC is at mutex_lock_nested+0xe8/0x3b0
LR is at mutex_lock_nested+0xd0/0x3b0
Cc: stable@vger.kernel.org
Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If mac80211 adds a vif with a different mac address respect to
the eeprom one, the device will not be able to connect to the ap
since the hw address has not been updated.
Fix the issue updating hw mac address in mt7601u_add_interface routine
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1516935
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove static qualifier from mt7601u_set_macaddr routine and move it
in mac related code in order to be used to properly support vif with
different mac address respect to the default one
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix following sparse warnings in mt76x2_mac_write_txwi:
- drivers/net/wireless/mediatek/mt76/mt76x2_mac.c:201:26: warning:
incorrect type in assignment (different base types)
- drivers/net/wireless/mediatek/mt76/mt76x2_mac.c:201:26: expected
restricted __le32 [usertype] iv
- drivers/net/wireless/mediatek/mt76/mt76x2_mac.c:201:26: got unsigned
int [unsigned] [usertype] <noident>
- drivers/net/wireless/mediatek/mt76/mt76x2_mac.c:202:27: warning:
incorrect type in assignment (different base types)
- drivers/net/wireless/mediatek/mt76/mt76x2_mac.c:202:27: expected
restricted __le32 [usertype] eiv
- drivers/net/wireless/mediatek/mt76/mt76x2_mac.c:202:27: got unsigned
int [unsigned] [usertype] <noident>
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added a new debugfs file 'mids' to print the list of
virtual interfaces by MAC ID (MID). Allows mapping
between the internal MID used by FW and the actual
network interface used by the VIF. This is needed by
debugging tools.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Track the connection status per-VIF.
The data path code is also updated to support multiple VIFs.
This includes RX and TX VRING management, NAPI poll loops,
RX reordering and related code.
Power management code used to check if the main interface
is up or based on connection state of the main interface,
adapt this code to take all VIFs into account.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As more support is added for multiple VIFs, there is a need
to protect the wil6210_vif structure from access while it is
deleted (mainly from del_virtual_intf operation).
Instead of adding another mutex, use p2p_wdev_mutex and rename
it to vif_mutex to reflect the added role. Its existing roles
are similar so it extends nicely (for example it protects the
scan_request member which is also a member of wil6210_vif).
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for multiple VIFs in the cfg80211 operations start_ap,
stop_ap and change_beacon. This change allows starting multiple APs
using virtual interfaces.
The data path and most other operations are still working only
on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add generic support in cfg80211 operations add_virtual_intf
and del_virtual_intf for adding/removing VIFs of any
interface type, and fix change_virtual_intf to allow changing
the interface type of a VIF. Previously these operations
only worked for the P2P_DEVICE interface which is not a real
VIF(it is management-only and shares radio with the main
interface).
Currently the interface combination is validated, the VIF is
added/removed in the firmware and the appropriate net/wireless
device is also added/removed.
Added minimal support for proper interface up/down and module
unload but most operations still work only on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple infrastructure changes for supporting multiple
virtual interfaces (multiple VIFs).
It is still not possible to add new VIFs so the only VIF
belongs to the main interface.
Main changes:
1. Add MAC ID(mid) argument to wmi_send and wmi_call to
allow invoking WMI commands on different VIFs.
2. Similarly, in WMI event handler look at the mid reported
by FW and extract VIF structure (currently only for main
interface). All WMI event handlers operate on wil6210_vif
structure so they know on which VIF they were called.
3. Trivial changes to use wil6210_vif structure and MID
throughout the code.
4. Various changes to logging to report MID.
More complete multiple VIFs support will be added gradually
in next patches.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW which supports multiple virtual interfaces, reports
its allowed interface combinations using a special comment
record in the FW file. The format of the interface combinations
is similar to the kernel wiphy->iface_combinations.
When parsing FW file during module initialization, also parse
and validate the concurrency record, and initialize
wiphy->n_iface_combinations and wiphy->iface_combinations
accordingly.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For supporting multiple virtual interfaces in the future,
introduce a wil6210_vif structure which will hold per-VIF
data. Change the module initialization so wil6210_vif will
be part of net_device structure, and wireless_dev will be
embedded inside the wil6210_vif structure. This will allow
us to find the appropriate wil6210_vif structure when we
only have access to wireless_dev or net_device.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wcn36xx_cancel_hw_scan method stops the hw scan and notify the
scan completion via ieee80211_scan_completed.
However, on scan offload cancellation, firmware sends a scan complete
indication, triggering a new call to ieee80211_scan_completed.
This leads to kernel warn since the scan has already been completed.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Ack timing generation has to be adapted for 5/10 MHz channels.
Do it by properly initializing ack shift field in TXSIFS
register. Ack shift assumes channel width of 2.5 Mhz so
value zero means 2.5 MHz, 1 is 5 MHz and so on.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bitrate value for airtime calculation is specified for
full rates. We need to divide it for 5 and 10MHz channels to
get correct result.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer tq is initialized with &ah->ah_txq[queue] and then a few
lines later is re-assigned the same value, hence this duplicate
assignment is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/ath/ath5k/qcu.c:326:25: warning: Value stored
to 'tq' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preparation for a new QCA9377 firmware release. The new firmware release
requires more IRAM banks, hence update that on ath10k.
The IRAM banks promotion won't break any backwards compatibility, as those IRAM
banks were not getting used in previous firmware releases.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HIF power-on failure is applicable to each underlying
bus type. Fix log message for hif power on failure.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was detected with static analysis using Coccinelle:
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b1ant.c:1107:5-18:
duplicated argument to && or ||
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bit pattern IEEE80211_CHAN_NO_IR is being bit-wise or'd twice;
remove the redundant 2nd IEEE80211_CHAN_NO_IR
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
nl80211 already allows specifying 48 bytes, but brcmfmac
only supports 32. Reject keys that are too long.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_firmware_callback() two pointer variables were used
pointing to the same construct. Get rid of sdiodev variable.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reducing the number of trace level messages in sdio code giving
them sdio log level instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No longer needed to call this in bus layer so make it static and call
it in the last phase of brcmf_attach() instead.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the function in preparation of subsequent patch.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By calling brcmf_usb_up() during brcmf_bus_preinit() it does not need
to be called in brcmf_usb_bus_setup().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now we can move brcmf_attach() until after the firmware has been downloaded
to the device. Make the call just before brcmf_bus_started().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allocate the control rx buffer needed for firmware control interface
during brcmf_sdio_bus_preinit(). This relies on common layer setting
struct brcmf_bus::maxctl during brcmf_attach(). By moving the allocation
we can move brcmf_attach() in subsequent change.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the brcmf_bus_preinit() call allows the bus code to do some
required initialization before handling firmware control messages.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multiple interfaces with same bss type could affect each other if
they are sharing the same mac address. In this patch, different
mac address is assigned to new interface which have same bss type
with exist interfaces.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In pci probe() function start firmware loading, protocol handshake
and driver core initialization, and not wait for completion.
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch enables rmmod/insmod for qtnfmac kernel modules:
- do not 'pin' pci device in order to disable it on module unload
- implement card reset procedure
- restore PCI bar addresses for restarted wireless card
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add missing PCI unmap for Tx buffers and release all buffers explicitly.
Managed release using devm_add_action is not suitable for qtnfmac Tx/Rx
data buffers. The reason is in ordering and dependencies: buffers
should be released after transmission is stopped but before PCI
device resources and DMA allocations are released.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-8 points out that source and destination of the memcpy() are
always the same pointer, so the effect of memcpy() is undefined
here (its arguments must not overlap):
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c: In function '_rtl_rx_process':
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:430:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
Most likely this is harmless, but it's easy to just remove the
line and get rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In _rtl92c_get_txpower_writeval_by_regulatory() the variable writeVal
is assigned to itself in an if ... else statement, apparently only to
document that the branch condition is handled and that a previously read
value should be returned unmodified. The self-assignment causes clang to
raise the following warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:304:13:
error: explicitly assigning value of variable of type 'u32'
(aka 'unsigned int') to itself [-Werror,-Wself-assign]
writeVal = writeVal;
Delete the branch with the self-assignment.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer q is initialized and then almost immediately afterwards being
re-assigned the same value. Remove the second redundant assignment.
Cleans up clang warning:
drivers/net/wireless/zydas/zd1211rw/zd_mac.c:503:23: warning: Value
stored to 'q' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wifi only btcoex is used to solo card (without BT), and it is also
useful to exclude the interference with BT to make debug easier.
There are only four ops for wifi only btcoex to initialze antenna and
switch the settings while band is changed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tell wifi and BT firmware the default port ID to set multiports' state
properly, but only 8822be needs this function currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new component phydm need to access efuse content, so we prepare ops
for reference.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add rf mask definition (BIT 0, BIT 1, BIT 2, ...) that is different from
rf path definition (0, 1, 2, ...), and then combinations of rf path are
possible.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NSS is a argument of highest rate in RC, and it occupies bit 4-7 so use
ieee80211_rate_set_vht() to fill the values. Since it got correct rate
index, we don't need to check chips to assign NSS in set function anymore.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add comments to make it to be easier to understand, and add compile time
assertions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In older design, the TX power is grouped into rate section (smaller array
size), but new design groups them into rate (larger array size). Thus,
we extend the size for both cases, and add compile time assertion.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In new design, SW_DEFINE[1:0] of tx desc are used by firmware, and the TX
report only contains SW_DEFINE[7:0]. To satisfy with all cases, driver uses
SW_DEFINE[7:2] as sequence number.
Besides, the format of tx report have been changed, so a new flag
RTL_SPEC_EXT_C2H is used to access report.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are going to add 8822be, which is a VHT 2x2 wifi chip, so add VHT flag
to replace enumeration of chips.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable the mac80211 fast-tx feature, since our driver already support
hw_flags required by fast-tx and is able to let mac80211 stack to transmit
packet through fast-xmit path.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case there is no valid MAC address kernel generates random one. This
patch propagate this generated MAC address back to NVS data which will be
uploaded to wl1251 chip. So HW would have same MAC address as linux kernel
uses.
This should not change any functionality, but it is better to tell wl1251
correct mac address since beginning of chip usage.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements parsing MAC address from NVS data which are sent to
wl1251 chip. Calibration NVS data could contain valid MAC address and it
will be used instead of randomly generated one.
This patch also moves code for requesting NVS data from userspace to driver
initialization code to make sure that NVS data will be there at time when
permanent MAC address is needed.
Calibration NVS data for wl1251 are device specific. Every device with
wl1251 chip should have been calibrated in factory and needs to provide own
calibration data.
Default example file wl1251-nvs.bin, found in linux-firmware repository,
contains MAC address 00:00:20:07:03:09. So this MAC address is marked as
invalid as it is not real device specific address, just example one.
Format of calibration NVS data can be found at:
http://notaz.gp2x.de/misc/pnd/wl1251/nvs_map.txt
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this patch, driver generated random MAC address every time it was
initialized. After that random MAC address could be overwritten with fixed
one, if provided.
This patch changes order. First it tries to read fixed MAC address and if
it fails then driver generates random MAC address.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If kmemdup fails, then wl->nvs_len will contain invalid non-zero size.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in debug error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever ath10k firmware discards a packet (HTT_TX_COMPL_STATE_DISCARD
flag), the skb is freed and mac80211 does not get feedback through
ieee80211_tx_status().
Instead, make sure that the IEEE80211_TX_STAT_ACK flag is disabled and
let the packet go through, like ath9k does.
Signed-off-by: Ignacio Nunez Hernanz <nacho.nunez@aoifes.com>
[kvalo@codeaurora.org: rebase patch manually]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit c713fb071e ("rtlwifi: rtl8821ae: Fix connection lost problem
correctly") a problem in rtl8821ae that caused loss of signal was fixed.
That same problem has now been reported for rtl8723be. Accordingly,
the ASPM L1 latency has been increased from 0 to 7 to fix the instability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
-----BEGIN PGP SIGNATURE-----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=A6XK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates across wireless.
One thing to note: I've included a new ethertype
that wireless uses (ETH_P_PREAUTH) in if_ether.h.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
-----BEGIN PGP SIGNATURE-----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=kwiY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support to get ack signal in probe client response
and in station info from user.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
[squash in compilation fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're obviously not part of a memory reclaim path, so don't set the flag.
This also causes a warning in check_flush_dependency() since we end up
in a code path that flushes a non-reclaim workqueue, and we shouldn't do
that if we were really part of reclaim.
Reported-by: syzbot+41cdaf4232c50e658934@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Canceling the periodic timestamp work should be
done in the opposite flow to where it was started.
This also prevents from sending the MARKER command
during the mac_stop flow - causing a false queue hang
(FW is no longer there to send a response).
Fixes: 93b167c13a ("iwlwifi: runtime: sync FW and host clocks for logs")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our Transmit Frame Descriptor (TFD) is a DMA descriptor that
includes several pointers to be able to transmit a packet
which is not physically contiguous.
Depending on the hardware being use, we can have 20 or 25
pointers in a single TFD. In both cases, it is more than
enough and it is quite hard to hit this limit.
It has been reported that when using specific applications
(Ktorrent), we can actually use all the pointers and then
a long standing bug showed up.
When we free the TFD, we check its number of valid pointers
and make sure it doesn't exceed the number of pointers the
hardware support.
This check had an off by one bug: it is perfectly valid to
free the 20 pointers if the TFD has 20 pointers.
Fix that.
https://bugzilla.kernel.org/show_bug.cgi?id=197981
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In IBSS, the mac80211 sets the cab_queue to be invalid.
However, the multicast station uses it, so we need to override it.
A previous patch did it, but it was nested inside the if's and was
applied only for legacy FWs that don't support the new station type
API, instead of being applied for all paths.
In addition, add a missing NL80211_IFTYPE_ADHOC to the initialization
of the queues in iwl_mvm_mac_ctxt_init()
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.
This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.
Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.
Fixes: f1ae02b186 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJafIqwAAoJEG4XJFUm622bY1AH/jlWytWm+1/u8BTPFje0soxI
8ISNaTDVKu2s2DjCO7liuDGoQ/YqmYBYm0rc53RB0xI6hTSzdlD59gio9vUR6mF7
VQWhJ+L8H1mD0mJOwKP+VY/z0nkNK9QwOPZIO/sdspTp9LP207zSILabZEn58PEp
KKINTJagkBHb1zIm5Zl9jyin4PsOKRzWfp8z532Mw61S3+m8CbsKrRXnCB++gNAn
71a5ScPScsW/ROnJV9clx6CEsme5irFDz9qcknfz8se9do9uj+0kgkxFWGB+gnRl
2Mz3EIVhkEaZ4IMVXlv6yhan4bfkpsbPavw/hO2iHbLfZNpXrWEM+zIoSzOmOoc=
=BJaf
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git fixes for 4.16. Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
Commit 8da58553cc ("ath9k: Use calibrated noise floor value
when available") introduced regression in ath9k_hw_getchan_noise
where per chain nominal noise floor has been taken instead default
for channel.
Revert to original default channel noise floor.
Fixes: 8da58553cc ("ath9k: Use calibrated noise floor value when available")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with
a custom Ubiquiti vendor and device id. This patch adds support for
those devices, treating them as a QCA988X v2.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of DRAM dump for QCA6174 hw3.0/hw3.2 and QCA9377 hw1.1
are less than the actual value, some coredump contents are missed.
To fix it, change the length from 0x90000 to 0xa8000.
Fixes: 703f261dd7 ("ath10k: add memory dump support for QCA6174/QCA9377")
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection lost problem")
Cc: Stable <stable@vger.kernel.org> # 4.14+
Fix-suggested-by: Pkshih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids data connection stalls when the client toggles powersave mode
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids timeouts on reordered A-MPDU rx frames
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With software A-MPDU reordering in place, frames that notify mac80211 of
powersave changes are reordered as well, which can cause connection
stalls. Fix this by implementing powersave state processing in the
driver.
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Make the dump operation aware of changes on radio list and corresponding
inconsistent dumps. Changed variable name for better understanding.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[compress ternary operator]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a NL_ERR_MSG in case of creating a radio by a netlink message to give
clear output to the creating process instead of creating only a debug
message in kernel log. The same function is used for the creation while
module load, so keep the old message, although it should never be thrown
while load, because the module controls all mac addresses.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[remove message, add missing braces]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If simulation needs predictable permanent mac addresses of hwsim wireless
phy, this patch add the ability to create a new radio with a user defined
permanent mac address. Allowed mac addresses needs to be locally
administrated mac addresses (as also the former fixed 42:* and 02:* were).
To do not break the operation with legacy software using hwsim, the new
address is set twice. The problem here is, the netlink call backs use
wiphy->addresses[1] as identification of a radio and not the proposed
permanent address (wiphy->addresses[0]). This design decision is not
documented in the kernel repo, therefore this patch simply reproduces this,
but with the same address.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[make pointer const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
mt76
* validate CCMP PN from received frames to avoid replay attacks
qtnfmac
* support 64-bit network stats
* report more hardware information to kernel log and some via ethtool
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaa1x7AAoJEG4XJFUm622bdc8H/3JSWFnXlkrQvjZzL1NWR0Hn
vUYou/W04mgzYtXIcscNL3otDa9TGwLW6Sr5wP0MDH/TGU9zXoEZxBxnYy4zq4np
7ZP7M6VsOzOhlNNsTcNAiMGyObtIT4btrfKlmp2yvf3Sra7nHNJJmprFeuyH3f02
vk5ZQWjMcEAe0afBGPcHrzndoAvVqIHHOAbM/w694n/8cdT8edcQeQ8rwlFO6ENU
db9yqkr4RvjWv9oJwa2us6d0lolJDk8ATWhDTyZL40X9yk84XR7E0jMdN5LQ/CJj
CCCMWsDYjUpEDUJVmwLdXzGavgo43QAs9a+O+z7MDJ4uwqYkZh3rzQZay+dYLKk=
=D4LX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
mt76
* validate CCMP PN from received frames to avoid replay attacks
qtnfmac
* support 64-bit network stats
* report more hardware information to kernel log and some via ethtool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently hardware does not perform CCMP PN validation in hardware, so
we need to take care of this in the driver. This is important for
protecting against replay attacks.
Since validation of fragmented frames is more complex, the CCMP header
for those is preserved. To keep the counter in sync, the first fragment
is verified by both mt76 and mac80211, and all other fragments only by
mac80211.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a separate function for processing frames after A-MPDU reordering,
reduce code duplication
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is required for performing CCMP PN validation in software
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids the rhashtable lookup based on the MAC address inside mac80211
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preparation for passing in more internal rx data via skb->cb
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like beacons, probe responses need a hardware-generated TSF value. Set
the flag that causes the hw to generate it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sending frames to mac80211 needs time, which could allow for more rx
packets to end up in the DMA ring. Retry polling until there are no more
frames left. Improves rx latency under load.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.16. Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
Add 'static' or declaration to resolve the warnings, and remove two unused
functions halbtc_set_macreg() and halbtc_get_macreg() exposed when they
were made static.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx_dxe_init() doesn't check for the return value of
wcn36xx_dxe_init_descs(), release the resources in case an error ocurred.
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 series allows to calibrate noise floor for different frequency
bins. Once it's done it's possible to get more accurate rssi/signal
values over whole frequency band at a given temperature.
The RSSI/signal accuracy reported by calibrated RF cards improves
from 6 to up to 2dB.
This could be interesting for application which require good signal
accuracy like roaming or mesh protocols.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 devices can have calibrated noise floor values
which can be used instead of hard coded one. Read them
from eeprom and save interpolated value in nf limits for
the current channel.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AR9003 factory calibration allows to use bigger EEPROM than
standard 1k without changing the default layout. Allow
probing of EEPROM at alternative address if initial check
for default fails.
The original ar9003 eeprom ops are still be used.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe device ID has changed in Talyn.
Add this ID to wil6210_pcie_ids list to allow
recognition of Talyn device.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using the firmware api it can fail simply because firmware does
not like the request or it fails due to issues in the host interface.
Currently, there is only a single error code which is confusing. So
adding a parameter to pass the firmware error separately and in case
of a firmware error always return -EBADE to user-space.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The protocol layer api defines callbacks for dongle commands.
Although not really well documented these should only return an
error code in case of an error, or 0 upon success. In the bcdc
protocol it can return value above 0 and we carry a fix in the
caller of the protocol layer api. This patch makes it adhere to
the intent of the api as described above.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Events processing requires locking of bus mutex, which is also used by
cfg80211 layer before calling several of cfg80211 callbacks. Since all
cfg80211 callbacks in qtnfmac driver also lock bus mutex, this
potentially may lead to a deadlock.
Do not use bus lock for event processing. Use RTNL lock instead to
serialize events and commands processing threads.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function qtnf_scan_done makes use of mutexes which is wrong
since it may be called from timer context. Move scan timeout
handler from timer to deferred work.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA does not reconnect to the same AP after disconnect. The reason is
that STA is marked as disconnected in cfg80211 disconnect callback.
This is too early since in this case qtnfmac event handler skips
cfg80211_disconnected call when processing disconnect event from
the card. As a result, wdev is left in an inconsistent state.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Validate new interface combinations using wireless core checks when new
interface is added or when the type of existing interface is modified.
This is performed to make sure that new interface combination is supported
by hardware. As a result, invalid interface combinations are rejected early,
rather than passed to hardware with sometimes unpredictable results.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update existing code handling configuration of supported interface
combinations. Current implementation is not complete since it does
not report multiple interface combinations which are incompatible
with each other. Instead current implementation packs all the
supported combinations into single entry.
In fact currently qsr10g wireless card supports the following
two distinct interface combinations:
1. STA/repeater: 1 STA and/or 1 AP
{
{ .max = 1, .types = NL80211_IFTYPE_AP},
{ .max = 1, .types = NL80211_IFTYPE_STA},
}
2. AP/mBSS
{
{ .max = 8, .types = NL80211_IFTYPE_AP},
}
The list of supported configuration is reported by firmware during
wireless card bring-up. Communication protocol between firmware
and host has been updated accordingly in order to accommodate passing
multiple interface combination entries.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable reporting of qtnfmac hardware and firmware details
using ethtool command.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Various bits of hardware and firmware versions are useful for debug
and troubleshooting. Get more information from the wireless card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On 32-bit platforms packet counters are stored in a net_device_stats struct
as unsigned long integers. As a result, after some time of network activity
an overflow takes place in network packet counters. This patch makes use of
new structs for holding interface statistics.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Virtual interface should be deleted after calling unregister_netdevice
since this function ends up with sending updown_intf command to card.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV is used to pass ACL data to firmware in start_ap cfg80211 callback.
Use the same approach in set_mac_acl cfg80211 callback.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field spec_ver is IC's specification mask for common code to do proper
process to specified IC. This commit add a field new rate ID for new
generation IC.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New generation ICs will support 11ac, 5G, n-NSS, etc, so we define a set of
rate ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822be is 2x2 11ac wifi chip, so report VHT capability to mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In files halbtc8822b1ant.c and halbtc8822b2ant.c that I will submit later,
two undesired directives named BT_8822B_1ANT_COEX_DBG and
BT_8822B_2ANT_COEX_DBG will be replaced by boolean variables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally, btcoex controls the antenna of combo card, but solo card
is also needed to setup properly. The new ops are named with suffix
'_wifi_only' opposited to original btc_ops, and new structures and
definitions are also introduced. The wifi_only oly contains four ops that
are initial variable, hw config, scan notify, and switch band notify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Three steps of connection procedure are scan, enter/leave IPS, auth.
There is no scan between leaving IPS and sending auth, but btcoex use scan
as an important clue that indicates user is going to connect. So add scan
notifications in ips_notify to correct btcoex's state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable will be used by btcoex of 8822be, so we prepare this variable
in advance.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BT shares 2.4G band but not 5G band, so inform current band to btcoex to
setup antenna properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rtlwifi newer ICs support 80M bandwidth in 5G band, so extend
get_wifi_bw() to know bandwidth 80M that helps btcoex to make correct
decisions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a possible race in mt76x2_stop_hardware() since pre_tbtt and
dfs tasklets could run during driver cleanup. Fix it disabling all
pending tasklets during device removal
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not enable DFS state machine if dfs region is set to NL80211_DFS_UNSET
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add mt76x2_dfs_set_domain routine in order to properly reconfigure
pattern detector when DFS domain has been changed
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Substitute tasklet_kill with tasklet_disable/tasklet_enable in order to
guarantee dfs tasklet can not be executed during dfs parameter
initialization
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hardware encryption seems to break encrypted unicast mgmt tx.
Unfortunately the hardware TXWI header does not have a bit to indicate
that a frame is software encrypted, so sw-encrypted frames need to use a
different WCID. For that to work, the CCMP PN needs to be generated in
software, which makes things a bit slower, so only do it for keys that
also need to tx management frames.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix hw queue configuration since mt76x2 devices use a reverse queue
enumeration respect to mac80211 one:
- 0: AC_BE
- 1: AC_BK
- 2: AC_VI
- 3: AC_VO
The issue can be reproduced sending two concurrent flow using
two separate queues:
- VO: 20Mbps UDP traffic
- BE: TCP traffic
In this scenario the UDP traffic will be blocked by the TCP one.
Fix it configuring properly WMM hw queue parameters
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* possible memory leak fix in hwsim
* speed up hwsim
* add hwsim userspace rate control API
* code cleanups
-----BEGIN PGP SIGNATURE-----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=HBMm
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Less than a handful of changes:
* possible memory leak fix in hwsim
* speed up hwsim
* add hwsim userspace rate control API
* code cleanups
====================
A conflict was resolved in mac80211_hwsim.c, mostly of
the simple overlapping changes category. One adding
a rhashtable and another adding a workqueue.
Signed-off-by: David S. Miller <davem@davemloft.net>
'hwname' is malloced in hwsim_new_radio_nl() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
Final few patches before the merge window, nothing really special.
ath9k
* add MSI support (not enabled by default yet)
rtlwifi
* support A-MSDU in A-MPDU aggregation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaYa7GAAoJEG4XJFUm622bp+IIAJuAvqfr5G1056cmvvpIDF1i
tsiNcmTkYlV33+99t1GXLgXATM5oYLOe4KLgVk+SxG2mCn2ZIun/TUUExM8tebIr
a6U1loiWhvztBHkzSglfIGknFHH6Ib6gZ6ti6cb5PpZE/ey1bsjlNBjvI5k2di5h
2KobJfQPk34e/DgJI49wYO6CwuzuT+rnNaWFzKEUoKm6lwGeUqpukV90gXN1O/qj
Xt2A9xIlUUEXHBfkJIef34+YMs/c9jeXqwoBMZIs8G/tQGeYOMjqbn7kTLW1MpMX
bu+59PCmshGdM/OMJsOZux5tm4DFGWaK/FYkedAJ1i5u4WzBEr1IJfo19es4oJM=
=kFNX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Final few patches before the merge window, nothing really special.
ath9k
* add MSI support (not enabled by default yet)
rtlwifi
* support A-MSDU in A-MPDU aggregation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
One last set of fixes for regression submitted during the last few days.
bcma & ssb
* fix older build problems which (apparently) recently became more
frequent in certain MIPS configurations
brcmfmac
* continue driver initialisation even if CLM blob (firmware) file is
not found
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaX1qzAAoJEG4XJFUm622bVWMH/RnqtoYG9fJzpvcssqmL5Ugd
GTpZ3wwEkrbwqylLtGH+886UuCcUGvfqVct9q76wy1LeAEwRrOyjUfLhswmWVIQM
rYYo193KqYjQnaxXLQmP9tkFNTOqBmDrT7nofalRA31b1GYL/4faD2ppGYhGE5IM
wk/UBJfi3hRo6juXbw568+GjNxtVERLG/2ULzDKAeMdvn8jvsHprWlc4pG/Oh9td
/OS+oi/P7dTCqUeo62lZID0wSiQJgTJNosxReskGmpQkI5bJGZaKK6KBhwsajinS
djrpGlOUULn421/liY83averZGFrLr92CCgEVew2N/HGL8bm6uul0rVLkKgHwq0=
=ZpvB
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-01-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
One last set of fixes for regression submitted during the last few days.
bcma & ssb
* fix older build problems which (apparently) recently became more
frequent in certain MIPS configurations
brcmfmac
* continue driver initialisation even if CLM blob (firmware) file is
not found
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that A-MSDU deaggregation is done in software,
we set this flag to support the A-MSDU in A-MPDU
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex configure antenna by rfe_type that is RF type programmed in efuse.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit implement the common function to sort old features, and add
more new features that are get_supported_feature, get_supported_version,
get_ant_det_val, ble_scan_type, ble_scan_para, bt_dev_info,
forbidden_slot_val, afh_map and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these typedefs are only referenced in a single location later
in this header. Thus, they are easily removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove global variables, so btcoexist can support multiple instances
simultaneously.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After mac power-on sequence, wifi will start to work so notify btcoex the
event to configure registers especially related to antenna. This will not
only help to assign antenna but also to yield better user experience.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When AP change bandwidth setting from 20M to 40M, STA may use old 20M AP
information to association with AP. Driver unlink bss in the
.bss_info_changed of ieee80211_ops to make sure that later scan can get
correct AP bandwidth capability.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there is no connection, driver will enter IPS state. Meanwhile, it
fails to scan channel 1 by the command 'iw dev wlan0 scan freq 2412',
because hardware channel setting lose after IPS. Thus, restore channel
setting from hw->conf.channel set by last rtl_op_config().
Signed-off-by: Tim Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enter/leavel IPS and LPS are large critical section, and they can't use
sleep function because running in atomic-context, which own a spin_lock.
In commit ba9f93f82a ("rtlwifi: Fix enter/exit power_save"), it moves
LPS functions to thread-context, so this commit can simply change LPS's
spin lock to mutex.
Considering IPS functions, rtl_ips_nic_on() may be called by TX tasklet
(softirq-context) that check whether packet is auth frame. Fortunately,
current mac80211 will ask driver to leave IPS using op_config with
changed flag IEEE80211_CONF_CHANGE_IDLE, before issuing auth frame, so
IPS functions can run in thread-context and use mutex to protect critical
section, too.
Also, this commit removes some useless spin locks.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Verify wcid is not NULL before dereferencing the pointer to initialize
txwi rate/power info
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize mt76_txq pointer after ieee80211_txq pointer check.
Remove space after the pointer cast
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For legacy chips without CLM blob files, kernel with user helper function
returns -EAGAIN when we request_firmware(), and then driver got failed
when bringing up legacy chips. We expect the CLM blob file for legacy chip
is not existence in firmware path, but the -ENOENT error is transferred to
-EAGAIN in firmware_class.c with user helper.
Because of that, we continue with CLM data currently present in firmware
if getting error from doing request_firmware().
Cc: stable@vger.kernel.org # v4.15.y
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify()
usage with device_lock()") resolves races between driver reset and
removal, but it introduces some new deadlock problems. If we see a
timeout while we've already started suspending, removing, or shutting
down the driver, we might see:
(a) a worker thread, running mwifiex_pcie_work() ->
mwifiex_pcie_card_reset_work() -> pci_reset_function()
(b) a removal thread, running mwifiex_pcie_remove() ->
mwifiex_free_adapter() -> mwifiex_unregister() ->
mwifiex_cleanup_pcie() -> cancel_work_sync(&card->work)
Unfortunately, mwifiex_pcie_remove() already holds the device lock that
pci_reset_function() is now requesting, and so we see a deadlock.
It's necessary to cancel and synchronize our outstanding work before
tearing down the driver, so we can't have this work wait indefinitely
for the lock.
It's reasonable to only "try" to reset here, since this will mostly
happen for cases where it's already difficult to reset the firmware
anyway (e.g., while we're suspending or powering off the system). And if
reset *really* needs to happen, we can always try again later.
Fixes: b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Cc: <stable@vger.kernel.org>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit b713bbf147.
The "fix" in question does not actually fix all related problems, and it
also introduces new deadlock possibilities. Since commit b014e96d1a
("PCI: Protect pci_error_handlers->reset_notify() usage with
device_lock()"), the race in question is actually resolved (PCIe reset
cannot happen at the same time as remove()). Instead, this "fix" just
introduces a deadlock where mwifiex_pcie_card_reset_work() is waiting on
device_lock, which is held by PCIe device remove(), which is waiting
on...mwifiex_pcie_card_reset_work().
The proper thing to do is just to fix the deadlock. Patch for this will
come separately.
Cc: Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable fw_ps_state is assigned a value but it is never read, hence
it is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:736:2:
warning: Value stored to 'fw_ps_state' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch found these issues:
drivers/net/wireless/ath/ath10k/ce.h:324: Please use a blank line after function/struct/union/enum declarations
drivers/net/wireless/ath/ath10k/core.c:1321: Please don't use multiple blank lines
drivers/net/wireless/ath/ath10k/htt.h:1859: Please use a blank line after function/struct/union/enum declarations
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable section_table.size is a u32 and so cannot be less than
zero, hence the less than zero check is redundant and can be
removed.
Detected by CoverityScan, CID#1463855 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Validate ie_len after the alignment padding before access the buffer
to avoid potential overflow.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some platform(BIOS) blocks legacy interrupts (INTx), and only allows MSI
for WLAN device. So adding a quirk to list those machines and set
use_msi automatically.
Adding the following platforms to the quirk.
Dell Inspiron 24-3460
Dell Inspiron 3472
Dell Inspiron 14-3473
Dell Vostro 3262
Dell Vostro 15-3572
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On new Intel platforms like ApolloLake, legacy interrupt mechanism
(INTx) is not supported, so WLAN modules are not working because
interrupts are missing, therefore this patch is to add MSI support to
ath9k. With module paremeter "use_msi=1", ath9k driver would try to
use MSI instead of INTx.
Signed-off-by: Russell Hu <rhu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaWd2WAAoJEG4XJFUm622bDnsH/2+Y5MEn31xvv7FGP46dHCNB
wk1SgcQOQdb7taIpZ++tFvhTQOXwrtGMA5iAFLeg9+07tqGIaZQqr58aab7BCQTi
2PgUK9sEdI5LPw3KmhnaqfHMVDKMaYdjcAhLG4FzJqMoDfTuPr56Vnnde3J2A0mj
hhFRarNKBArEvRaWtNypdZQN8HM10v3LJq+HNnK/yep7fW2EuwSwTO2YBqDhrwAD
0gzfV6yi05497uVv6W+5CKRawu7RoYgbFTaEa8rmCViIjf9bK4gPdsW18a/DTNMz
MfvLF2RQZk1k944+a+a983oqZNkq9dEWd0kF0CSFgbO3r/SO7264yc4PHpZKy/s=
=2eQ4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Here are patches which have been accumulating over the holidays and
after the New Year. Business as usual and nothing special really
standing out.
But what's noteworthy here is that Larry Finger is stepping down as
the rtlwifi maintainer. He has been maintaining rtlwifi since it was
applied back in 2010 in commit 0c8173385e ("rtl8192ce: Add new
driver") and it has been no easy role trying to juggle between the
vendor, demanding upstream community and users. So big thank you to
Larry for all his efforts!
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
qtnfmac
* support MAC address based access control
* support for radar detection and Channel Availibility Check (CAC)
mwifiex
* firmware coredump for usb devices
rtlwifi
* Larry Finger steps down as the maintainer and Ping-Ke Shih becomes
the new maintainer
* add debugfs interfaces to dump register and btcoex status, and also
write registers and h2c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For correct interpretation of a tx rate, the corresponding rate flags are
needed (e.g. whether a HT-MCS rate or a legacy rate) and moreover for more
correct simulation the other infos of the flags are important (like
short-GI). Keeping compatibility, the flags are not integrated into the
existing hwsim_tx_rate, but transmitted as an additional netlink attribute.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a rhastable for mac address lookup of hwsim radios. This
especially improve the speed on reception of a netlink message with a new
frame. Although redundant, we keep holding a normal list for all radios,
since the rhashtable_walk interface adds a lot of overhead for iterating
over all radios and the doc of rhashtable recommend a redundant structure
for stable walks in such situations.
Since rhashtable is rcu protected we do not need a lock for delivering
frames and thus improving this scenario.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[remove hash function, it would cause alignment issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When creating a new radio on the fly, hwsim allows this
to be done with an arbitrary number of channels, but
cfg80211 only supports a limited number of simultaneous
channels, leading to a warning.
Fix this by validating the number - this requires moving
the define for the maximum out to a visible header file.
Reported-by: syzbot+8dd9051ff19940290931@syzkaller.appspotmail.com
Fixes: b59ec8dd43 ("mac80211_hwsim: fix number of channels in interface combinations")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When closing multiple wmediumd instances with many radios and try to
unload the mac80211_hwsim module, it may happen that the work items live
longer than the module. To wait especially for this deletion work items,
add a work queue, otherwise flush_scheduled_work would be necessary.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
b43_radio_2057_init_post is not called in an interrupt handler
nor holding a spinlock.
The function mdelay in it can be replaced with usleep_range,
to reduce busy wait.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use dma_zalloc_coherent for allocating zeroed
memory and remove unnecessary memset function.
Generated-by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename functions to brcmf_sdio_skbuff_{read,write}() as we pass an
skbuff to this function.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_buscore_read() there is some special handling upon
register access to chipid register of the chipcommon core. Add
comment explaining why it is done here.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace the array of functions with a pair of pointers to the
relevant functions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Small cleanups in the new rate-scaling code;
* Some improvements in debugging;
* New FW API changes;
* Fix a bug where we got a false-positive warning;
* Fix forced quota debugfs functionality;
-----BEGIN PGP SIGNATURE-----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=gWyv
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third batch of updates for v4.16
* Small cleanups in the new rate-scaling code;
* Some improvements in debugging;
* New FW API changes;
* Fix a bug where we got a false-positive warning;
* Fix forced quota debugfs functionality;
ath.git patches for 4.16. Major changes:
ath10k
* more preparation work for wcn3990 support
* add memory dump to firmware coredump files
wil6210
* support scheduled scan
* support 40-bit DMA addresses
Hopefully the last set of fixes for 4.15.
iwlwifi
* fix DMA mapping regression since v4.14
wcn36xx
* fix dynamic power save which has been broken since the driver was commited
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVLeaAAoJEG4XJFUm622bYBUH/2NhQwUJbKIrbxYhYpo0d++8
GK3TjxpzTByCe0nXGUT5iuDaY72i9C2UoLhFQ5smVg04pE0IXQQjZus6vSGx4biz
GUave/SkzL0EruUXjXLBYWiYDND4iynk82gWX2/Lh7qGoT2SQfD5cKz0cMdE5NrW
E7Q1CMiaoB0i9jcksaU2uWA0XPwISxl61kU2dXuKHQOJ1CW1goI/YIHsBajshHmi
ZEfMqxZFE+jz2Kkp4tKhvG/Xva0ylJv8bwK8CMK6MqA8oa3xdgOhv67E9mm7IGpD
ETrRLJNnWGJlnod5u7QOZWcS01gAgT5whCqDl/lTEty0823kvjMQdwckQaIU+AE=
=me16
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
Hopefully the last set of fixes for 4.15.
iwlwifi
* fix DMA mapping regression since v4.14
wcn36xx
* fix dynamic power save which has been broken since the driver was commited
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a running AP to blacklist STAs by their MAC addresses
respecting the configured policy (either accept or deny unless listed).
It can be setup on .start_ap or with .set_mac_acl commands.
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Keep generation in per-VIF data structure and increment it whenever STA
list is changed. Use generation value to fill struct station_info when
required.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A set of per-STA statistics can potentially change quite often.
To ensure backwards and forward compatibility,
modify GET_STA_STATS command format:
- introduce two TLV types
- first TLV is a variable-sized bitmap of statistics values
that are filled by firmware
- second TLV is a structure with statistics itself
Only values specified in first TLV are valid.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are needed to inform userspace about features the hardware
supports (e.g. BSS Transition Management 802.11v)
Signed-off-by: Vasily Ulyanov <vulyanov@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix RSSI values passed to wireless core by qtnfmac driver:
- fix RSSI values in scan results:
driver registers wiphy with CFG80211_SIGNAL_TYPE_MBM signal type,
so mBm should be passed using DBM_TO_MBM macro
- accompany firmware changes fixing RSSI values in received mgmt frames
update qlink message format and pass correct signed values to core
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parameters passed into .mgmt_tx callback may have a NULL channel in case
userspace wants to send a frame on current channel. Make sure this case
is handled, pass "freq==0" in case channel is not specififed to tell
wlan device to use current channel.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To mimic mac80211 behaviour, change default interface type from AP to STA.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement two parts of radar handling logic:
- cfg80211 .start_radar_detect callback to allow nl80211 to initiate CAC
- radar event to allow wlan device to advertize CAC and radar events
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Center frequency is not enough to describe the channel in HT and VHT
modes. For 40MHz and 80MHz channels both primary channel and center
frequency should be specified in order to qualify channel completely.
This change adds primary channel info into qlink_chandef structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is possible that regulatory notifier is called before MAC data
was allocated. We need to verify that MAC data exists before trying
to send a regulatory change event.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The second assignment to msg_body.min_ch_time is incorrect, it
should actually be to msg_body.max_ch_time.
Thanks to Bjorn Andersson for identifying the correct way to fix
this as my original fix was incorrect.
Detected by CoverityScan, CID#1463042 ("Unused Value")
Fixes: 2f3bef4b24 ("wcn36xx: Add hardware scan offload support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It was accidentally left out from the switch statement and target info was not
queried.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
[kvalo@codeaurora.org: add commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function does not exist and thus, the prototype can be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field preset_chandef of wireless_dev must not be accessed
by the driver because it is private to cfg80211. Store the
monitor channel locally in wil6210_priv instead.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"FIXME: IRQ mask debug" and "FIXME: interrupts enabled - for debug"
can be removed because wil6210_debug_irq_mask() is now considered
production feature.
"FIXME FW can transmit only ucast frames to peer" and "FIXME real
ring_id instead of hard coded 0" can be removed because FW/HW already
support multicast transmission.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Suspend and crash dump operations can happen simultaneously
in case there is a FW assert during the suspend procedure
or when SSR calls all the devices crashdump callbacks.
To prevent that, a new flag is added, indicating that the
dumps collection is in progress, in order to allow the
suspend/reset decline if the dumps collection already started.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some cases the platform should be aware of the FW capabilities
to decide which feature to enable.
For example, FW can control the external REF clock for power saving.
Driver should notify the platform about that, to allow platform
power management optimization.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add get_capa callback to platform ops to allow reading the platform
capabilities.
Supported capabilities:
- Keeping 11ad connection during suspend
- T_POWER_ON 0 support
- Usage of external clock
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the option to support 40bit addresses since some platforms
may not support 48bits but support 40bits
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for sched_scan_start/stop by sending PNO commands to FW.
Driver reports max_sched_scan_reqs and invokes
cfg80211_sched_scan_results upon receiving WMI_SCHED_SCAN_RESULT_EVENTID
from FW.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fix a typo in rt2800lib.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the less than zero error check on ret is incorrect
as it is checking a far earlier ret assignment rather than the
return from the call to wl1251_acx_arp_ip_filter. Fix this by
adding in the missing assginment.
Detected by CoverityScan, CID#1164835 ("Logically dead code")
Fixes: 204cc5c44f ("wl1251: implement hardware ARP filtering")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pausing queue without checking threshold is racy with txdone path.
Moreover we do not need pause queue on any error, but only if queue
is full - in case when we send RTS frame ( other cases of almost full
queue are already handled in rt2x00queue_write_tx_frame() ).
Patch fixes of theoretically possible problem of pausing empty
queue.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not drop &queue->tx_lock and acquire it again to pause queue when
available entries are below the threshold.
Patch should mitigate problem of frequently printed errors:
"Error - Dropping frame due to full tx queue"
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Enrico Mioso@gmail.com
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The last command used to shutdown firmware might be timeout,
and trigger firmware dump in asynchronous pcie/sdio work.
The remove/shutdown handler will continue free core data
structure private/adapter, which might be dereferenced in
pcie/sdio work, finally crash the kernel.
Sync and Cancel pcie/sdio work, could be a fix for above
cornel case. In this way, the last command timeout could
be handled properly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch extend device_dump debugfs function to make it
works for usb interface.
For command timeouts, USB firmware will automatically emit
firmware dump events, so we don't implement device_dump().
For user-initiated dumps, we trigger it by issue firmware
dump event command to firmware, as there is no command
response, do not start 10s timer.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware dump on usb interface is different with current
sdio/pcie chipset, which is based on register operation.
When firmware hang on usb interface, context dump will be
upload to host using 0x73 firmware debug event.
This patch store dump data from debug event and send to
userspace using device coredump API.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch refactor current device dump code to make it generic
for subsequent implementation on usb interface.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix typo in 5GHz power vs channel eeprom parsing
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently if the allocation of skb fails and returns NULL then the
call to skb_put will cause a null pointer dereference. Fix this by
checking for a null skb and returning NULL. Note that calls to
function mt76x2_mcu_msg_alloc don't directly check the null return
but instead pass the NULL pointer to mt76x2_mcu_msg_send which
checks for the NULL and returns ENOMEM in this case.
Detected by CoverityScan, CID#1462624 ("Dereference null return value")
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt76x2_mac_start writes dev->rxfilter to the hardware. It also happens
during init, before dev->rxfilter is filled with the initval register
value, leading to issues like promisc mode being enabled
unconditionally.
Fix this by reading the default value into dev->rxfilter earlier
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to an unrelated issue, the MT_RX_FILTR_CFG_PROMISC flag is currently
unset, which means that monitor mode is unconditionally enabled.
Toggle this flag based on the mac80211 monitor mode setting instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is no longer necessary for client mode operation, vif index entries
8-16 are no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Using both chains adds max. 3 dBm. A similar worst-case calculation is
being used in ath9k as well to ensure that the hardware stays within
regulatory limits
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows user space to query the real hardware limits directly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Discard affected packets instead. Should reduce the frequency of bogus
bug reports
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/mediatek/mt76/mt76x2_main.c:86:5-8: Unneeded variable: "ret". Return "0" on line 112
Remove unneeded variable used to store return value.
Generated by: scripts/coccinelle/misc/returnvar.cocci
Fixes: a5f6039c8f9c ("mt76: add driver code for MT76x2e")
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/mediatek/mt76/debugfs.c:36:0-23: WARNING: fops_regval should be defined with DEFINE_DEBUGFS_ATTRIBUTE
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Fixes: a5f6039c8f9c ("mt76: add driver code for MT76x2e")
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add 43455 into the save-restore(SR) capable chip list, so
the SR engine will be enabled with 43455 FW which built-in the -sr
function.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make it more obvious that this code acually enables interrupts, and
provide nice definitions for the bits in the register.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for removing the function array, remove all code that
refers to function by index and replace with pointers to the function
itself.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: replace BUG() with WARN() macro]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Its more efficient to test the register we're interested in first,
potentially avoiding two more comparisons, and therefore always avoiding
one comparison per call on all other chips.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
[arend: fix some checkpatch warnings]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
func0 is not provided by the mmc stack as a function when probing.
Instead providing specific access functions to read/write it.
This prepares for a patch to remove the actual array entry itself.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: rephrased the commit message]
[arend: removed unrelated comment for which separate patch is warranted]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rather than workaround the restrictions on func0 addressing in the
driver, set MMC_QUIRK_LENIENT_FN0
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IO functions operate within the Chipcommon IO window. Explicitly
set this, rather than relying on the last initialisation IO access to
leave it set to the right value by chance.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoid confusion with unrelated _buscore labels.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: only do the rename]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove yet another IO function from the code and replace with one
that already exists.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: keep address calculation, ie. (base + offset) in one line]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit fills FW version information of RTL8188EE and RTL8723, so
the btcoex can cooperate with FW correctly.
Also, we can display this version in debugfs.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We use seq_file to replace RT_TRACE to dump status, then we can use 'cat'
to access btcoex's status through debugfs.
(i.e. /sys/kernel/debug/rtlwifi/00-11-22-33-44-55-66/btcoex)
Other related changes are
1. implement btc_disp_dbg_msg() to access btcoex's common status.
2. remove obsolete field bt_exist
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use debugfs to dump register and btcoex status, and also write registers
and h2c.
We create topdir in /sys/kernel/debug/rtlwifi/, and use the MAC address
as subdirectory with several entries to dump mac_reg, bb_reg, rf_reg etc.
An example is
/sys/kernel/debug/rtlwifi/00-11-22-33-44-55-66/mac_0
This change permits examination of device registers in a dynamic manner,
a feature not available with the current debug mechanism.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without firmware, driver wastes time to download and wait for MCU bootup,
and then kernel core dump finally. If request_firmware fails, the value
max_fw_size=0 is set, so we check the value before downloading firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit a221cb0911 ("staging:
rtlwifi: Remove unnecessary parentheses"), and original commit log
is reserved below.
Remove unnecessary parentheses to comply with preferred coding style for
the linux kernel and avoid the following checkpatch's message:
'CHECK: Unnecessary parentheses around'.
Credits to checkpatch.
Signed-off-by: Frank A. Cancio Bello <frank@generalsoftwareinc.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit 640019bba4 ("staging:
rtlwifi: mark expected switch fall-through in rtl_make_smps_action"),
and original commit log is reserved below.
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit 596e0559d6 ("Staging:
rtlwifi: Remove unnecessary 'out of memory' message."), and commit log
is reserved below.
Logging messages that show some type of "out of memory" error
are generally unnecessary as there is a generic message and
a stack dump done by the memory subsystem.
These messages generally increase kernel size without much
added value.
Problem found by checkpatch.
Signed-off-by: Shreeya Patel <shreeya.patel23498@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit 85d309d53f ("staging:
rtlwifi: use kcalloc instead of multiply"), and original commit log
is reserved below.
checkpatch emits multiple warnings of type
WARNING:ALLOC_WITH_MULTIPLY: Prefer kcalloc over kzalloc with multiply
Replace two calls to kzalloc() with calls to kcalloc().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit 688a0206cf ("staging:
rtlwifi: fix parenthesis alignment"), and original commit log is
reserved below.
Checkpatch emits multiple warnings of type
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
Fix parenthesis alignment in line with checkpatch suggestion.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit dc33bd4309 ("staging:
rtlwifi: check for array overflow"), and the original commit log is
reserved below.
Smatch is distrustful of the "capab" value and marks it as user
controlled. I think it actually comes from the firmware? Anyway, I
looked at other drivers and they added a bounds check and it seems like
a harmless thing to have so I have added it here as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
22000 devices (previously referenced as A000) can support
short transmit queues. This means that we have less DMA
descriptors (TFD) for those shorter queues.
Previous devices must still have 256 TFDs for each queue
even if those 256 TFDs point to fewer buffers.
When I introduced support for the short queues for 22000
I broke older devices by assuming that they can also have
less TFDs in their queues. This led to several problems:
1) the payload of the commands weren't unmapped properly
which caused the SWIOTLB to complain at some point.
2) the hardware could get confused and we get hardware
crashes.
The corresponding bugzilla entries are:
https://bugzilla.kernel.org/show_bug.cgi?id=198201https://bugzilla.kernel.org/show_bug.cgi?id=198265
Cc: stable@vger.kernel.org # 4.14+
Fixes: 4ecab56160 ("iwlwifi: pcie: support short Tx queues for A000 device family")
Reviewed-by: Sharon, Sara <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
-----BEGIN PGP SIGNATURE-----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=M0gz
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-01-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have things all over the place, no point listing them.
One thing is notable: I applied two patches and later
reverted them - we'll get back to that once all the driver
situation is sorted out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver does not report hardware dynamic power saving cap,
this is up to the mac80211 to manage power saving timeout and
state machine, using the ieee80211 config callback to report
PS changes. This patch enables/disables PS mode according to
the new configuration.
Remove old behaviour enabling PS mode in a static way, this make
the device unusable when power save is enabled since device is
forced to PS regardless RX/TX traffic.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add memory dump to the firmware crash data file which is provided to user space
via devcoredump interface. This makes it easier for firmware engineers to debug
firmware crashes.
Due to increased memory consumption the memory dump is disabled by default. To
enable it make sure that bit 3 is set in coredump_mask module parameter:
modprobe ath10k_core coredump_mask=0xffffffff
When RAMDUMP is enabled a buffer for the dump is allocated with vmalloc during
device probe. The actual memory layout is different in hardware versions and
the layouts are defined in coredump.c. The memory is split to regions and, to
get even finegrained control of what to copy, the region can split to smaller
sections as not all registers are readable (which could cause the whole system
to stall).
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
[kvalo@qca.qualcomm.com: refactoring and cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For memory dump support (it consumes quite a lot of memory) we need to control
what is exactly stored to the crash dump. Add a module parameter call
coredump_mask to do that. It's a bit mask of these values:
enum ath10k_fw_crash_dump_type {
ATH10K_FW_CRASH_DUMP_REGISTERS = 0,
ATH10K_FW_CRASH_DUMP_CE_DATA = 1,
ATH10K_FW_CRASH_DUMP_MAX,
};
For example, if we only want to store CE_DATA we would enable bit 2:
modprobe ath10k_core coredump_mask=0x2
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now coredump is totally separate from debug.c and doesn't depend on
CONFIG_ATH10K_DEBUGFS anymore, only on CONFIG_DEV_COREDUMP. Also remove
leftovers from the removed debugfs file support.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation to add RAM dump support. No functional changes, only moving code
and renaming function names.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The fw_crash_dump file was deprecated by commmit 727000e6af ("ath10k: support
dev_coredump for crash dump") in v4.11 in favor of dev_coredump interface,
remove it now for good. Everyone should use dev_coredump now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable TDLS wider bandwidth support for 5GHz based on firmware wmi capabilities.
This patch is required for chipset QCA9888. Tested with firmware version
10.4-3.5.1-00018.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware is not loaded via bmi. The bmi specific
code should not be executed for HL1.0
Add fw feature flag for non bmi targets and skip the bmi
specific code for non bmi targets.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 is integrated chipset which uses system NOC.
Add SNOC bus type and related definitions.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 CE descriptor uses 64bit address for
src/dst ring buffer. It has extended field for toeplitz
hash result, which is being used for HW assisted
hash results.
To accommodate WCN3990 descriptor, define new CE
descriptor for extended addressing mode and related
methods to handle the descriptor data.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE send and receive API's are using u32 ring address, which
truncates the address for target with 64bit addressing range.
Use dma_addr_t for ce buffers to support target with extended
addressing range.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
paddrs_ring_64 holds the physical device address of the
rx buffers that host SW provides for the MAC HW to fill.
Since this field is used in rx ring setup and rx ring
replenish in rx data path. Define separate methods
for handling 64 bit ring paddr and attach them dynamically
based on target_64bit hw param flag. Use u64 type
while popping paddr from the rx hash table for 64bit target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 uses larger ring size in comparison to existing
ring size value.
Add rx ring size hw param for supporting different rx ring
size across multiple target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frags_paddr in htt tx descriptor,
which holds the physical address of SKB fragments in tx data path.
In order to support 64 bit bit frags_paddr in htt tx descriptor, define
htt_data_tx_desc_64 descriptor and ath10k_htt_tx_64 method for handling
tx data path with new descriptor fields.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target uses 64 bit frag descriptor and more
fields in TSO flag.
Add support for 64 bit HTT frag descriptor.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3900 target uses 64bit rx_ring_base_paddr and
fw_idx_shadow_reg_paddr fields in HTT rx ring cfg message.
These address points to the memory region where remote
ring empty buffers are allocated.
In order to add 64 bit htt rx ring cfg, define separate
64 bit htt rx ring cfg message and attach it in runtime
based on target_64bit hw param flag.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target use 64bit msdu address in htt in-order
indication message. Add support for 64 bit msdu address in
HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND message.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 rx descriptor uses different offset of msdu start, msdu end,
ppdu end, rx pkt end and rx frag info.
To accommodate different offsets, define respective fields in
rx descriptor of WCN3990 target.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WCN3990 target supports 37-bit addressing mode. In order
to accommodate extended address support, add hw param to
indicate if the target supports addressing above 32-bits.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The #ifdef checks are hard to get right, in this case some functions
should have been left inside a CONFIG_PM_SLEEP check as seen by this
message:
drivers/net/wireless/ath/wil6210/pcie_bus.c:489:12: error: 'wil6210_pm_resume' defined but not used [-Werror=unused-function]
drivers/net/wireless/ath/wil6210/pcie_bus.c:484:12: error: 'wil6210_pm_suspend' defined but not used [-Werror=unused-function]
Using an __maybe_unused is easier here, so I'm replacing all the
other #ifdef in this file as well for consistency.
Fixes: 94162666cd ("wil6210: run-time PM when interface down")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable fc is being assigned but never used, so remove it. Cleans
up the clang warning:
warning: Value stored to 'fc' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This aligns the code with the existing pattern to check
if the firmware has a certain capability.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently a new command was added to the firmware
for setting a MAC's low-latency mode. Use it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have TSO enabled, we might end up segmenting it and
queuing multiple packets before the queue is even enabled. This causes
a warning.
For example, when starting TCP traffic on a non-zero TID, the
first packets may not have DSCP and will be sent on TID 0, while
the actual data packets will be sent on the TID.
To prevent this, simply remove the warning.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This helps matching tx cmd with other trace events, like net_dev_xmit
and net_dev_queue etc.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need the _enum suffix.
Also refer to &enum iwl_tlc_mng_vht_he_types instead
of %IWL_TLC_MNG_VALID_VHT_HE_TYPES_\*
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Latest firmware calculates both phases of the TKIP
field, so the TTAK ok flag is not needed and deprecated.
Support this API change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For sync we send a marker cmd every <defined throughout debugfs> seconds.
The trigger for getting gp2 clock values from the FW is set by
writing to debugfs a periodic time in seconds,
if value zero is written, only one request would be sent
and the timer would be canceled.
Also added a small infrastructure for debugfs runtime code.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The way p2p NoA is forced in SCM (used for WFA tests)
is by setting a quota < 100% (simulating DCM).
A test-mode command is used for setting the NoA params.
In that case, force quota update or nothing will happen
if there was no significant change in the quota
at that exact point (which is likely to be the case).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.
Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support internal debug data collection on 9000 and newer
devices.
The method for finding the base and end address has changed
on new HW's, so introduce a new version of debug destination
tlv.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* hwsim:
- set To-DS bit in some frames missing it
- fix sleeping in atomic
* nl80211:
- doc cleanup
- fix locking in an error path
* build:
- don't append to created certs C files
- ship certificate pre-hexdumped
-----BEGIN PGP SIGNATURE-----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=OWs9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few more fixes:
* hwsim:
- set To-DS bit in some frames missing it
- fix sleeping in atomic
* nl80211:
- doc cleanup
- fix locking in an error path
* build:
- don't append to created certs C files
- ship certificate pre-hexdumped
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e937b8da5a.
Turns out that a new driver (mt76) is coming in through
Kalle's tree, and will conflict with this. It also has some
conflicting requirements, so we'll revisit this later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver may sleep under a spinlock.
The function call path is:
hwsim_get_radio_nl (acquire the spinlock)
nlmsg_new(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Same as in ieee80211_nullfunc_get, enable the TODS bit, otherwise the
nullfunc packet will not be handled in ap rx path.
(will be dropped in ieee80211_accept_frame()).
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ath.git patches for 4.16. Major changes:
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
Add hw params entry for wcn3990 and populate various
target specific values for wcn3990.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parameter values for skid limit, number of peers and wds
entries values which are sent in wmi init cmd are hardware
specific.
Add support to obtain skid limit, number of peers and wds entries
values from hw params which will have the hw specific values
for these parameters.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HL1.0 firmware branch, used in wcn3990, transmits management
frames by reference over WMI.
Add support for management tx by reference over WMI.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to the limitation of wmi tlv parsing logic, if there are
two parameters in a wmi event with same tlv tag, we can get only
the last value, as it overwrites the prev value of the same tlv tag.
The service ready event in wcn3990 contains two parameters of the
same tag UINT32, due to which the svc bitmap is overwritten with the
DBS support parameter.
Refactor the service ready event parsing to allow parsing two tlv
of the same tag UINT32 for wcn3990.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The purpose of pushing indication on a list and handle these in a
separate worker is to allow the handlers to sleep. It does therefor not
make much sense to hold the queue spinlock through the entire indication
worker function.
By removing items from the queue early we don't need to hold the lock
throughout the indication worker, allowing the individual handlers to
sleep.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch generates a warning here:
drivers/net/wireless/ath/ath9k/htc_drv_main.c:1688 ath9k_htc_ampdu_action()
error: buffer overflow 'ista->tid_state' 8 <= 15
I don't know if it's a real bug or not but the other paths through this
function all ensure that "tid" is less than ATH9K_HTC_MAX_TID (8) so
checking here makes things more consistent.
Fixes: fb9987d0f7 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Current hw_scan implementation does not trigger offloaded
hardware scan and seems to only put the device in a kind of
listening mode (beacon/probe-response) for software scan.
Since no probe request are generated by the software, current
scanning method is similar to a passive scan.
This patch introduces support for 'true' hardware offloaded scan.
Hardware scan is configured and started via the start-scan-offload
firmware message. Once scan has been completed a scan indicator
message is received from firmware.
Moreover, this patch includes support for directed probe-request,
allowing connection with hidden APs. It also fixes scan issues with
band-steering AP which are not 'visible' with passive scan (due to
hidden ssid in beacons).
Let's keep the 'legacy' scanning method in case scan-offload is not
supported.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.2.4 firmware branch (used in QCA988X) does not support
HTT_10_4_T2H_MSG_TYPE_PEER_STATS and that's why ath10k does not provide
tranmission rate statistics to user space, instead it just shows
hardcoded 6 Mbit/s. But pktlog firmware facility provides per peer tx
statistics. The firmware sends one pktlog event for every four
PPDUs per peer, which include:
* successful number of packets and bytes transmitted
* number of packets and bytes dropped
* retried number of packets and bytes
* rate info per ppdu
Firmware supports WMI_SERVICE_PEER_STATS, pktlog is enabled through
ATH10K_FLAG_PEER_STATS, which is nowadays enabled by default in ath10k.
This patch does not impact throughput.
Tested on QCA9880 with firmware version 10.2.4.70.48. This should also
work with firmware branch 10.2.4-1.0-00029
Parse peer stats from pktlog packets and update the tx rate information
per STA. This way user space can query about transmit rate with iw:
$iw wlan0 station dump
Station 3c:a9:f4:72:bb:a4 (on wlan1)
inactive time: 8210 ms
rx bytes: 9166
rx packets: 44
tx bytes: 1105
tx packets: 9
tx retries: 0
tx failed: 1
rx drop misc: 3
signal: -75 [-75, -87, -88] dBm
signal avg: -75 [-75, -85, -88] dBm
tx bitrate: 39.0 MBit/s MCS 10
rx bitrate: 26.0 MBit/s MCS 3
rx duration: 23250 us
authorized: yes
authenticated: yes
associated: yes
preamble: short
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 22 seconds
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move pktlog_filter from struct ath10k_debug to struct ath10k
so that pktlog can be enabled even when debugfs is not
enabled, needed to enable peer tx stats for 10.2.4.
No changes in functionality.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove CONFIG_MAC80211_DEBUGFS dependency on ath10k_sta_statistics().
ath10k_sta_statistics() has per sta tx/rx stats and this should not
be dependent on MAC80211_DEBUGFS.
No changes in functionality.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With current NAPI implementation, NAPI poll can deliver more frames
to net core than allotted budget. This may cause warning in napi_poll.
Remaining quota is not accounted, while processing amsdus in
rx_in_ord_ind and rx_ind queue. Adding num_msdus at last can not
prevent delivering more frames to net core. With this change,
all amdus from both in_ord_ind and rx_ind queues are processed and
enqueued into common skb list instead of delivering into mac80211.
Later msdus from common queue are dequeued and delivered depends on
quota availability. This change also simplifies the rx processing in
napi poll routine.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Data packets are not sent by STA in case of STA joined to
non QOS AP (WMM disabled AP). This is happening because of STA
is sending data packets to firmware from host with qos enabled
along with non qos queue value(TID = 16).
Due to qos enabled, firmware is discarding the packet.
This patch fixes this issue by updating the qos based on station
WME capability field if WMM is disabled in AP.
This patch is required by 10.4 family chipsets like
QCA4019/QCA9888/QCA9884/QCA99X0.
Firmware Versoin : 10.4-3.5.1-00018.
For 10.2.4 family chipsets QCA988X/QCA9887 and QCA6174 this patch
has no effect.
Signed-off-by: Balaji Pothunoori <bpothuno@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The newly added wlcore_fw_sleep function is called conditionally,
which causes a warning without CONFIG_PM:
drivers/net/wireless/ti/wlcore/main.c:981:12: error: 'wlcore_fw_sleep' defined but not used [-Werror=unused-function]
Instead of trying to keep track of what should be in the #ifdef and what
should not, it's easier to mark the top-level suspend/resume functions
as __maybe_unused so the compiler can silently drop all the unused code.
Fixes: 37bf241b8e ("wlcore: allow elp during wowlan suspend")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl_rx_ampdu_apply(), when rtlpriv->cfg->ops->get_btc_status()
returns false, RT_TRACE() is called with the values of variables
reject_agg and agg_size, which have not been initialized.
Always initialize these variables in order to prevent using
uninitialized values.
This issue has been found with clang. The compiler reported:
drivers/net/wireless/realtek/rtlwifi/base.c:1665:6: error: variable
'agg_size' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (rtlpriv->cfg->ops->get_btc_status())
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/base.c:1671:31: note:
uninitialized use occurs here
reject_agg, ctrl_agg_size, agg_size);
^~~~~~~~
drivers/net/wireless/realtek/rtlwifi/base.c:1665:6: error: variable
'reject_agg' is used uninitialized whenever 'if' condition
is false [-Werror,-Wsometimes-uninitialized]
if (rtlpriv->cfg->ops->get_btc_status())
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/base.c:1671:4: note:
uninitialized use occurs here
reject_agg, ctrl_agg_size, agg_size);
^~~~~~~~~~
Fixes: 2635664e6e ("rtlwifi: Add rx ampdu cfg for btcoexist.")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset the driver current tx read/write index to zero when inactiveps
nic out of sync with HW state. Wrong driver tx read/write index will
cause Tx fail.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Making this change to HIQ, which has high priority, improves the response
time for transmission after TBTT or beacon.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The buffer size of return of cap iovar is greater than 256 bytes in some
firmwares. For instance, the return size of cap iovar is 271 bytes in 4373
13.10.246.79 firmare. It makes feature capability parsing failed because
caps buffer is default value.
So we enlarge caps buffer size to 512 bytes and add the error print for
cap iovar error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to repeatdly call brcmf_chip_get_core(), which
traverses a list of cores every time its called (including during
register access code!).
Call it once, and store a pointer to the core structure. The existing
code does nto keep track of users of the cores anyway, and even so, this
will allow for easier refcounting in future.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro is used exactly nowhere in the code. Delete it.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Create a macro to make the code a bit more readable, whilst we're stuck
with using struct element offsets as register offsets.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: rename macro to SD_REG]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All functions that might require the window address changing call
brcmf_sdiod_set_backplane_window() prior to access. Thus resetting
the window is not required.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
[arend: corrected the driver prefix in the subject]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function has become trivial enough that it may as well be pushed into
its callers, which has the side-benefit of clarifying what's going on.
Remove it, and rename brcmf_sdiod_set_sbaddr_window() to
brcmf_sdiod_set_backplane_window() as it's easier to understand.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial tidy of register definitions.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Primarily this patch removes:
brcmf_sdiod_f0_writeb()
brcmf_sdiod_reg_write()
brcmf_sdiod_reg_read()
Since we no longer use the quirky method of deciding which function to
address via the address being accessed, take the opportunity to rename
some IO functions more in line with common kernel code. We also convert
those that map directly to sdio_{read,write}*() to macros.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whilst this if () statement is technically correct, it lacks clarity.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[arend: mention function in patch subject]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function needs to be split up into separate read / write variants
for clarity.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the ARRAY_SIZE macro on rfseq_updategainu_events to determine
size of the array. Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds an API to mac80211 to handle scheduling of TXQs and changes the
interface between driver and mac80211 for TXQ handling as follows:
- The wake_tx_queue callback interface no longer includes the TXQ. Instead,
the driver is expected to retrieve that from ieee80211_next_txq()
- Two new mac80211 functions are added: ieee80211_next_txq() and
ieee80211_schedule_txq(). The former returns the next TXQ that should be
scheduled, and is how the driver gets a queue to pull packets from. The
latter is called internally by mac80211 to start scheduling a queue, and
the driver is supposed to call it to re-schedule the TXQ after it is
finished pulling packets from it (unless the queue emptied).
The ath9k and ath10k drivers are changed to use the new API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enforce using PS_MANUAL_POLL in ps hwsim debugfs to trigger a poll,
only if PS_ENABLED was set before.
This is required due to commit c9491367b759 ("mac80211: always update the
PM state of a peer on MGMT / DATA frames") that enforces the ap to
check only mgmt/data frames ps bit, and then update station's power save
accordingly.
When sending only ps-poll (control frame) the ap will not be aware that
the station entered power save.
Setting ps enable before triggering ps_poll, will send NDP with PM bit
enabled first.
Signed-off-by: Adiel Aloni <adiel.aloni@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I accidentally pushed a patch with CPTCFG (which is used in the
backports project) to the rs-fw.c file. Fix that to use CONFIG
instead.
Fixes: 9f66a397c8 ("iwlwifi: mvm: rs: add ops for the new rate scaling in the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Initial work for rate-scaling offload;
* Support for new FW API version;
* Some fixes here and there;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAlom7g0ACgkQoUecoho8
xfo2Og//S/mE3HyKTUoFiulNggIGA+U7TEYnWZSlcqB/wSRJ7o6AP3LaAXt1PwZc
zqTO2zI3NnRXibmOV/5LEpF6R3hJ3WdtOMeuYR37hwEjqftKBKgvULAul0iq6zB0
M9C9hl17e2/Dvw5AOU0zsa7v/UjadE1HKp4sTqU5ssy7fgdmwmtVEdweQ9Or4wgA
BfCUlCPxLK1knoioDcYRyrex2zo+fkIzYAVyRNoepgv5a776Fd+lwbw8BWNQbD5b
P9EsONUH8ZWK9Ji1rY9YeSEoAOJcj4NJbjrXelIFT31ljF/rEFs9sjBe7EFtdCt+
rID8kRRZgp+6KsBcc8F+RCDDlJBE8WSY2Vz5GHWWIOtWhm11PkXwT5VCEJA8HAve
sYjX9GZ6cDtCJ93iQ4N/1hZXym25nR6JPGacAD3OAU3wY8BuDN+bsApJco1TPO0h
GBH49tK5HtY+oiuN74qn9l9G4Y1Y+HWNhDepZBdab1xJ9bF5667azW3z42Bm4qs1
dD83uHgy3929nN37VZ6gy3eHcWjaSQYDK1mznuxHfYDTTP1907PKv4TfwHL6dD73
hmuG5TnkrAMBYEGA5azTYuNCfQa6w+5185HrmkOb0HgNFNxcLOZ7ALD7DPy3SLG+
1fB/taoFqzlVDYXy8+UiJUQQGKM6HEtt9M4568YjHm2VXsR7nQc=
=Zstw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second batch of iwlwifi updates for v4.16
* Initial work for rate-scaling offload;
* Support for new FW API version;
* Some fixes here and there;
The 10.4 firmware defines this as a 3-bit field, as does the
mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF
at least in the firmware header I have seen. This patch
fixes the ath10k wmi header to match the firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Replace ntohs with be16_to_cpu to do endian conversions for ethhdr
h_proto assignment.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
At the moment, spectral scan support, and with it RELAY, is always enabled
with ATH10K_DEBUGFS. Spectral scan support is currently the only user of
RELAY in ath10k, and it unconditionally reserves a relay channel.
Having debugfs support in ath10k is often useful even on very small
embedded routers, where we'd rather like to avoid the code size and RAM
usage of the relay support. While ath10k-based devices usually have more
resources than ath9k-based ones, it makes sense to keep the configuration
symmetric to ath9k, so the same base kernel without RELAY can be used for
both ath9k and ath10k hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
At the moment, spectral scan support, and with it RELAY, is always enabled
with ATH9K[_HTC]_DEBUGFS. Spectral scan support is currently the only user
of RELAY in ath9k, and it unconditionally reserves a relay channel.
Having debugfs support in ath9k is often useful even on very small embedded
routers, where we'd rather like to avoid the code size and RAM usage of the
relay support.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The dump format uses 64-bit timestamps already, but calling
getnstimeofday() only returns a 32-bit number on 32-bit architectures,
so that will overflow in y2038.
This changes it to use ktime_get_real_ts64() instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To get rid of W=1 warning: variable ‘ies_len’ set but not used.
Variable ies_len is being assigned but never read.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.
-----BEGIN PGP SIGNATURE-----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=VSq5
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Third batch of iwlwifi patches intended for 4.15.
* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.
When I run make W=1 on gcc (Debian 7.2.0-16) 7.2.0 I got an error for
the first run, all next ones are okay.
CC [M] drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:2078: error: Cannot parse struct or union!
scripts/Makefile.build:310: recipe for target 'drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o' failed
Seems like something happened with W=1 and wrong kernel doc format.
As a quick fix remove dubious /** in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MT76x2e is a 2x2 PCIe 802.11ac chipset by MediaTek. This driver has full
support for AP, station, ad-hoc, mesh and monitor mode.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will be used by drivers for MT76x2e, MT7603e and MT7628
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
(1) Change virtual interface operation in cfg80211 process reset and
reinitilize private data structure.
(2) Scan result event processed in main process will dereference private
data structure concurrently, ocassionly crash the kernel.
The cornel case could be trigger by below steps:
(1) wpa_cli mlan0 scan
(2) ./hostapd mlan0.conf
Cfg80211 asynchronous scan procedure is not all the time operated
under rtnl lock, here we add the protect to serialize the cfg80211
scan and change_virtual interface operation.
Signed-off-by: Limin Zhu <liminzhu@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware do not support change interface from micro-ap mode
to station mode, forbid this operation
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in error message text. Also remove the
error message on an kzalloc failure as this is redundant.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
when enabling wowlan and entering suspend the last write to the firmware
allowing it to go into elp mode was not completing before suspend, leaving
the firmware running in full active mode consuming high power.
Use an immediate call instead of a work queue for this last access
allowing the firmware to go into power save during wowlan uspend.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Using getnstimeofday()/timespec_to_ns() causes an overflow on 32-bit
architectures in 2038, and may suffer from time jumps due to
settimeofday() or leap seconds.
I don't see a reason why this needs to be UTC, so either monotonic
or boot time would be better here. Assuming that the fw time keeps
running during suspend, boottime is better than monotonic, and
ktime_get_boot_ns() will also save the additional conversion to
nanoseconds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cck_poweri cannot be greated than 15 as is derived from the bottom 4 bits
from riv->channels[channel - 1].hw_value & 0xf. Hence the check for it
being greater than 15 is redundant and can be removed.
Detected by CoverityScan, CID#744303 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the duplicate checking of TX ring's available number, and remove
the variable to store available number that can be calculated by
read/write pointers.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Give correct fifo size to calculate fifo space. Fortunately, the values of
RTL_PCI_MAX_RX_COUNT and TX_DESC_NUM_92E are the same in old code, so it
still works.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check remaining count of RX packets cost a lot of CPU time, so only update
when the counter decreases to zero. In old flow, the counter was updated
once a RX packet is received.
Signed-off-by: Steven Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the RTL8822BE and later devices, the number of interrupt vectors
has grown from 2 to 4. At this point, saving and passing those vectors
in a struct makes more sense than using individual scaler variables.
In two of the drivers, code to process the second of the interrupt
registers was included, but commented out. This patch removes those
useless sections.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial cleanup of nasty variable name
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If you need debugging this low level, you're doing something wrong.
Remove these noisy debug statements so the code is more readable.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unlikely to be a problem, but brcmf_sdiod_regrl() is
not symmetric with brcmf_sdiod_regrb() in initializing
the data value on stack. Fix that.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
[arend: reword the commit message a bit]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is obfuscating how IO works on this chip. Remove it
and push its logic into brcmf_sdiod_reg_{read,write}().
Handling of -ENOMEDIUM is altered, but as that's pretty much broken anyway
we can ignore that.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register access code is not the place for band-aid fixes like this.
If this is a genuine problem, it should be fixed further up in the driver
stack.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value passed to brcmf_sdiod_addrprep() is *always* 4
remove this parameter and the unused code to handle it.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function sets the address of the IO window used for
SDIO accesses onto the backplane of the chip.
It currently uses 3 separate masks despite the full mask being
defined in the code already. Remove the separate masks and clean up.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This large function is concealing a LOT of obscure logic about
how the hardware functions. Time to split it up.
This first patch splits the function into two pieces - read and write,
doing away with the rw flag in the process.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 4 IO functions in this patch are incorrect as they use compiler types
to determine how many bytes to send to the hardware.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the other IO functions are the other way round in this
driver. Make this one match.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When statistics are read from debugfs, make sure that they
are actually updated from the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If FW loads without a problem, leaving init_dbg on can
cause a confusion, since the user won't necessarily
remember it is still turned on, and there are flows in
which everything continues as usual, only without
stopping the device after INIT, even if there is no FW
assert. On 22000 HW, for instance, this causes a
warning, since the paging is getting initialized twice.
Solve the issue by making this module param effective
only if the FW indeed asserts during INIT.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending LQ command, verify the rate scaling is not in firmware.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch sends to the FW notification configuration command and
handles the update responses.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch adds rate scaling configuration command and
implements a few other handlers.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the series will fill in the implementation).
The decision which API to use is done during the register
step according to FW TLV.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New devices will have rate scaling algorithm running in the firmware.
With this feature, the driver's responsiblity is to provide an initial
configuration and to handle notifications regarding recent rates and
some other parameters. Debugfs hooks will be still available for
reading the current rate/statistics and setting a fixed rate.
The old API is supported so far, though both APIs cannot be used
simultaneously.
This is the first patch in the series. It adds a new TLV specifying
FW support for the new API and updates lq_sta to support two types
of rate scaling.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We might erroneously get to error dumping code when the
device is already stopped.
In that case the driver will detect a defective value and will try to
reset the HW, assuming it is only a bus issue. The driver than
proceeds with the dumping.
The result has two side effects:
1. The device won't be stopped again, since the transport status is
already stopped, so the device remains powered on while it actually
should be stopped.
2. The dump in that case is completely garbaged and useless.
Detect and avoid this. It will also make debugging such issues
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the removal of non-DQA code, we don't need the queues
variable any more. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the WFA vendor specific TPC report IE to probe requests
when it is not added by the FW. The FW will still need to set
the tx power field.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When RADA is active, the hardware decrypts the packets and strips off
the MIC as it is useless after decryption. Indicate that to mac80211.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the flag that indicates that ICV was stripped on if
this option was enabled in the HW.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before deleting a time event (remain-on-channel instance), flush
the queue so that frames cannot get stuck on it. We already flush
the AUX STA queues, but a separate station is used for the P2P
Device queue.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
add 1 PCI ID for 9260 series and 1 for 22000 series.
Cc: stable@vger.kernel.org
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the function brcmf_sdio_firmware_callback() the driver is
unbound from the sdio function devices in the error path.
However, the order in which it is done resulted in a use-after-free
issue (see brcmf_ops_sdio_remove() in bcmsdh.c). Hence change
the order and first unbind sdio function #2 device and then
unbind sdio function #1 device.
Cc: stable@vger.kernel.org # v4.12.x
Fixes: 7a51461fc2 ("brcmfmac: unbind all devices upon failure in firmware callback")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the value for the firmware configuration parameters
BTC_STATIC_LEN_LE_BT and BTC_STATIC_LEN_LE_WLAN are not set the duty
cycle between BT and WLAN is such that if BT (including BLE) is active
WLAN gets 0 bandwidth. When tuning these parameters having a too high
value for WLAN means that BLE performance degrades.
The "sweet" point of roughly half of the maximal values was empirically
found to achieve a balance between BLE and Wi-Fi coexistence
performance.
Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org>
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the statistics show how many successful/failed
suspend/resume operations the system had.
Update the statistics by splitting each successful/failed
suspend/resume operations to radio on/off.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently suspend time statistics are showed through debugfs.
Remove time statistics in suspend state since the timing may
not be accurate in that state.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of interface down, radio is turned off but PCIe mastering is
not cleared.
This can cause unexpected PCIe access to the shutdown device.
Fix this by clearing PCIe mastering also in case interface is down
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a length check in wil_cfg80211_mgmt_tx to detect unsigned integer
overflow.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a length check in wmi_set_ie to detect unsigned integer
overflow.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading FW from file add block size checks to ensure a
corrupted FW file will not cause the driver to write outside
the device memory.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current length check:
sizeof(cmd) + len > r->entry_size
will allow very large values of len (> U16_MAX - sizeof(cmd))
and can cause a buffer overflow. Fix the check to cover this case.
In addition, ensure the mailbox entry_size is not too small,
since this can also bypass the above check.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On-going operations were not aborted properly
and required locks were not taken.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW capabilities are currently retrieved only during module
initialization, but userspace can replace the firmware while
interface is down, so refresh the FW capabilities when
interface is up (after FW is loaded) to ensure driver
functionality matches the loaded FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon sending/receiving WMI commands/events, print human readable
names in addition to id for easier debugging.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow run-time suspend when interface is down, keep card alive when
interface is up.
If driver is in wmi only or debug_fw mode run-time PM won't suspend.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle tdls peer events from the target. TDLS events for the peer
could be discover, teardown, etc. As of now, adding the logic to
handle tdls teardown events alone.
Teardown due to peer traffic indication(PTR) timeout is one such
teardown event from the target.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is required to update the teardown state of the peer when
a tdls link with that peer is terminated. This information is
useful for the target to perform some cleanups wrt the tdls peer.
Without proper cleanup, target assumes that the peer is connected and
blocks future connection requests, updating the teardown state of the
peer addresses the problem.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 4ca1807815 ("ath10k: disable wake_tx_queue for older devices")
disables the use of the mac80211 TXQs for some devices because of a theoretical
throughput regression. The original regression report[1] was related to
fq_codel qdisc drop performance, which was fixed in commit 9d18562a22
("fq_codel: add batch ability to fq_codel_drop()"). Since then, we have not
seen the TXQ-related regression, so it should be safe to re-enable TXQs.
[1] http://lists.infradead.org/pipermail/ath10k/2016-April/007266.html
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make use of the swap macro and remove unnecessary variable temp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
-----BEGIN PGP SIGNATURE-----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=j1dk
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi updates for v4.16
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
kvalo:
There were conflicts, I fixed them with taking into account commit c2c48ddfc8
("iwlwifi: fix firmware names for 9000 and A000 series hw"):
CONFLICT (content): Merge conflict in drivers/net/wireless/intel/iwlwifi/iwl-config.h
CONFLICT (modify/delete): drivers/net/wireless/intel/iwlwifi/cfg/a000.c deleted in ca495785063c428641cc6df8888afd2587ca6677 and modified in HEAD. Version HEAD of drivers/net/wireless/intel/iwlwifi/cfg/a000.c left in tree.
* One fix in rate-scaling;
* One fix for the TX queue hang detection for AP/GO modes;
* Fix the TX queue hang timeout used in monitor interfaces;
* Fix packet injection;
* Remove a wrong error message when dumping PCI registers;
* Fix race condition with RF-kill;
-----BEGIN PGP SIGNATURE-----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=eD7A
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Second batch of fixes intended for 4.15.
* One fix in rate-scaling;
* One fix for the TX queue hang detection for AP/GO modes;
* Fix the TX queue hang timeout used in monitor interfaces;
* Fix packet injection;
* Remove a wrong error message when dumping PCI registers;
* Fix race condition with RF-kill;
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since iwl_mvm_start_p2p_roc() is only called from iwl_mvm_roc(),
which already flushes the same work item, doing it again in it
is superfluous. Remove it and move the comment to the first one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ucode_major and ucode_minor were swapped. This has
no practical consequences since those fields are not used.
Same goes for umac_major and umac_minor which were only
printed under certain debug flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
-----BEGIN PGP SIGNATURE-----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=ODX1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-11-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Four fixes:
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.
Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
Even if no ALIVE was received, the WRT data can still
be collected. Add this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Starting from a version 35, the minor version should be
printed in hexa.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This feature was actually removed from firmware, but without
ever telling the driver. Since nobody is actually using it,
just remove it entirely without bothering with a capability
check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API will not be used, remove the code that
supports it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we are in a search cycle, we try different combinations
of parameters. Those combinations are called 'columns'.
When we switch to a new column, we first need to check if
this column has a suitable rate, if not, we can't try it.
This means we must not erase the statistics we gathered
for the previous column until we are sure that we are
indeed switching column.
The code that tries to switch to a new column first sets
a whole bunch of things for the new column, and only then
checks that we can find suitable rates in that column.
While doing that, the code mistakenly erased the rate
statistics. This code was right until
struct iwl_scale_tbl_info grew up for TPC.
Fix this to make sure we don't erase the rate statistics
until we are sure that we can indeed switch to the new
column.
Note that this bug is really harmless since it causes a
change in the behavior only when we can't find any rate
in the new column which should really not happen. In the
case we do find a suitable we reset the rate statistics
a few lines later anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In A000 family, compressed BA notifs can include MGMT
frames, so don't fail RXs in such a case.
While at it, since in A000 the TID for MGMT frames is
15, treat it in the RX flow as if received TID 8. This
way we won't require special handling of this TID.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This bit will be used in CCK to indicate short preamble.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting HW rfkill we get stop_device being called from
two paths.
One path is the IRQ calling stop device, and updating op
mode and stack.
As a result, cfg80211 is running rfkill sync work that shuts
down all devices (second path).
In the second path, we eventually get to iwl_mvm_stop_device
which calls iwl_fw_dump_conf_clear->iwl_fw_dbg_stop_recording,
that access periphery registers.
The device may be stopped at this point from the first path,
which will result with a failure to access those registers.
Simply checking for the trans status is insufficient, since
the race will still exist, only minimized.
Instead, move the stop from iwl_fw_dump_conf_clear (which is
getting called only from stop path) to the transport stop
device function, where the access is always safe.
This has the added value, of actually stopping dbgc before
stopping device even when the stop is initiated from the
transport.
Fixes: 1efc3843a4 ("iwlwifi: stop dbgc recording before stopping DMA")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current pci dumping code code is always falling to the error
path, resulting with a constant "Read failed" message, also
for the successful reads.
Fixes: a5c932e41fdd ("iwlwifi: pcie: dump registers when HW becomes inaccessible")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.
Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MONITOR type is missing in the interface type switch.
Add it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we act as an AP, new firmware versions handle
internally the power saving clients and the driver doesn't
know that the peers went to sleep. It is, hence, possible
that a peer goes to sleep for a long time and stop pulling
frames. This will cause its transmit queue to hang which is
a condition that triggers the recovery flow in the driver.
While this client is certainly buggy (it should have pulled
the frame based on the TIM IE in the beacon), we can't blow
up because of a buggy client.
Change the current implementation to not enable the
transmit queue hang detection on queues that serve peers
when we act as an AP / GO.
We can still enable this mechanism using the debug
configuration which can come in handy when we want to
debug why the client doesn't wake up.
Cc: stable@vger.kernel.org # v4.13
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ieee80211_rx_status::chains was always set to zero.
That caused rate scaling to always start with the
lowest rate possible (rs_get_initial_rate).
Set it correctly according to the MPDU response.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of fixes for 4.15. Most important here is the iwlwifi fix
for scan command firmware interface change.
ath10k
* fix CCMP-256, GCMP and GCMP-256 in raw mode, it was never working
wcn36xx
* fix device tree node search
iwlwifi
* fix a regression with firmware API change of scan cmd (introduced in
firmware version 34)
* add a bunch of PCI IDs and fix configuration structs for A000 devices
* fix the exported firmware name strings for 9000 and A000 devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaFZQwAAoJEG4XJFUm622bOe8H/0dmodmL+nf0MUKYyXmV2l5J
3wN0Xrse1NL3bRDTGZ/KkX/OFB1FSZ8ViGW0ek9DvbbF4lC9E5WqjM5HbTY7QE6i
bBgF476qnV9Hy/ay9SEMe7HhxsU8KfVKuYgNzY8pHhlCLkr96h35YNt+LtD319zT
PTBrxURLkZotr44mDQjO8duyKZFCafWN6F5nd22+JWpOEQDK4rUNNdDT/16CwQiy
aLqCF5bHB4kOigd9YfEpx1jO6GusqGqkB0x3lwG0QR7oygFgLZbWre0TllE+ly8P
x7gy40euxBWh9Hlk+4xjxBfZraE41XzXTTHyJECVRLKJcrlEvzCc+QCOyoYjZpY=
=uYE+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-11-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
First set of fixes for 4.15. Most important here is the iwlwifi fix
for scan command firmware interface change.
ath10k
* fix CCMP-256, GCMP and GCMP-256 in raw mode, it was never working
wcn36xx
* fix device tree node search
iwlwifi
* fix a regression with firmware API change of scan cmd (introduced in
firmware version 34)
* add a bunch of PCI IDs and fix configuration structs for A000 devices
* fix the exported firmware name strings for 9000 and A000 devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".
Done using the following semantic patch:
@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@
DEFINE_TIMER(_timer, _callback);
@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@
void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
{ ... }
Signed-off-by: Kees Cook <keescook@chromium.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mmio node was also prematurely freed.
Fixes: fd52bdae9a ("wcn36xx: Disable 5GHz for wcn3620")
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure 16-byte mic is removed from the rx data packet
tail when CCMP-256, GCMP and GCMP-256 ciphers are used
in raw decap mode. This fixed rx traffic failures in those
ciphers in raw mode. Split the helper returning crypto
tail length into two, one to get the ICV length and other
to get the mic lengh for the cipher to make it clean.
Fixes: 2ea9f12cef ("ath10k: add new cipher suite support")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hwsim_new_radio_nl() now copies the name attribute in order to add a
null-terminator. mac80211_hwsim_new_radio() (indirectly) copies it
again into the net_device structure, so the first copy is not used or
freed later. Free the first copy before returning.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAloRRxcACgkQoUecoho8
xfpeMhAAjzEShlwj9LHaPSmP+uFCONsbdrOtM9ObCKWtwXAJLRT0A9cOKl8s2R6a
cSfLRW58qW2Zx/2xpLJZVe220tAmfZi2iR7dW+wglRnBKkKDwn9xV6MllO1kXOrt
Rm6WpC0TJH7ye2EJ7NSnHnreINKEISXJdZQD+7YI/LmeiFKfOEkqkIG1STtYyhr2
DUK7wcFxV90huRGOKmORdXJCK5nLqyhO4mc17y18DAfs9lnZxEzahZUPeJK3IVD7
77rj+AcRExwS4Otr+qEdd/YqD/poWxqWmYyEsFQwcFOe+rV1uHg6plfdYQokGaEV
kVA4sDIFf6X6BD/xNyd9XgJeqFCzYnnN5rAZ+jckqsK0XhlAvCQsTvZOSbZ7gFL1
kbZ3K6rD5XmKauRoxQXeuJ9wf4JwwEdyBNI035E4m1Rw+uzSY8SFDbGDzUZ3s/Hg
7ekKEkcv8FDARIOTZQRkqyBCrLLaM/kHe8jp9zRGcfQfK4BUY9jGF6WeqDkgp4gp
U88VWHBfLBGLvcsf/kUckDSddDxFy9EvSRfTj//YXRHCnQxY7kebI/GsI16b67rh
Ryfy0ln3xeAPxts0r7o9kiLHVajAFFPKEY+9f9De2cpFd+Hx/2M4szkemBM6n8fj
1Y2evaPlXtg/1ao2woBl33+ItmCnipSLQKVUVyXuJJdz0Olw3OM=
=JPn9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
iwlwifi: first set of fixes for 4.15
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
In the cases where len is too long, the error return path fails to
kfree allocated buffers buf and usb_reg_buf. The simplest fix is to
perform the sanity check on len before the allocations to avoid having
to do the kfree'ing in the first place.
Detected by CoverityScan, CID#1452258,1452259 ("Resource Leak")
Fixes: 59f73e2ae1 ("rsi: check length before USB read/write register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi 9000 and a0000 series hw contains an extra dash in firmware
file name as seeen in modinfo output for kernel 4.14:
firmware: iwlwifi-9260-th-b0-jf-b0--34.ucode
firmware: iwlwifi-9260-th-a0-jf-a0--34.ucode
firmware: iwlwifi-9000-pu-a0-jf-b0--34.ucode
firmware: iwlwifi-9000-pu-a0-jf-a0--34.ucode
firmware: iwlwifi-QuQnj-a0-hr-a0--34.ucode
firmware: iwlwifi-QuQnj-a0-jf-b0--34.ucode
firmware: iwlwifi-QuQnj-f0-hr-a0--34.ucode
firmware: iwlwifi-Qu-a0-jf-b0--34.ucode
firmware: iwlwifi-Qu-a0-hr-a0--34.ucode
Fix that by dropping the extra adding of '"-"'.
Signed-off-by: Thomas Backlund <tmb@mageia.org>
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A lot of PCI IDs were missing and there were some problems with the
configuration and firmware selection for devices on the 9000 series.
Fix the firmware selection by adding files for the B-steps; add
configuration for some integrated devices; and add a bunch of PCI IDs
(mostly for integrated devices) that were missing from the driver's
list.
Without this patch, a lot of devices will not be recognized or will
try to load the wrong firmware file.
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
According to the description, first argument of genlmsg_nlhdr() points to
what genlmsg_put() returns, i.e. beginning of user header. Therefore we
should only subtract size of genetlink header and netlink message header,
not user header.
This also means we don't need to pass the pointer to genetlink family and
the same is true for genl_dump_check_consistent() which is the only caller
of genlmsg_nlhdr(). (Note that at the moment, these functions are only
used for families which do not have user header so that they are not
affected.)
Fixes: 670dc2833d ("netlink: advertise incomplete dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Newer firmware versions (such as iwlwifi-8000C-34.ucode) have
introduced an API change in the SCAN_REQ_UMAC command that is not
backwards compatible. The driver needs to detect and use the new API
format when the firmware reports it, otherwise the scan command will
not work properly, causing a command timeout.
Fix this by adding a TLV that tells the driver that the new API is in
use and use the correct structures for it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=197591
Fixes: d7a5b3e9e4 ("iwlwifi: mvm: bump API to 34 for 8000 and up")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
The firmware for brcmfmac devices includes information regarding
regulatory constraints. For certain devices this information is kept
separately in a binary form that needs to be downloaded to the device.
This patch adds support to download this so-called CLM blob file. It
uses the same naming scheme as the other firmware files with extension
of .clm_blob.
The CLM blob file is optional. If the file does not exist, the download
process will be bypassed. It will not affect the driver loading.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"INVALID_STATE" is already being returned in the default case and this
code cannot be reached.
Addresses-Coverity-ID: 1398384
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2x00 uses the deprecated do_gettimeofday() function to get a timestamp
for its debugfs "dump" file interface.
The timestamp is using an unsigned 32-bit value, so we could make it
work until 2106 by using ktime_get_real_ts64(), but it seems better to
use monotonic times, as we normally want for timestamps.
Since this is an interface change, I'm incrementing the
DUMP_HEADER_VERSION number, so user space can figure out whether the
timestamps are monotonic or not. Most likely the tools won't care either
way.
Generally speaking, ABI version numbers and in particular changing them
is a bad idea. However since this is in debugfs, we don't put any
API stability rules on the interface according to
Documentation/filesystems/debugfs.txt, and we can take the easy way
out here; anyone using the frame dump feature can probably work out
the differences here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ENOENT usb error mean "specified interface or endpoint does not exist or
is not enabled". Mark device not present when we encounter this error
similar like we do with ENODEV error.
Otherwise we can have infinite loop in rt2x00usb_work_rxdone(), because
we remove and put again RX entries to the queue infinitely.
We can have similar situation when submit urb will fail all the time
with other error, so we need consider to limit number of entries
processed by rxdone work. But for now, since the patch fixes
reproducible soft lockup issue on single processor systems
and taken ENOENT error meaning, let apply this fix.
Patch adds additional ENOENT check not only in rx kick routine, but
also on other places where we check for ENODEV error.
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Debugged-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifically, following parameters are needed for wireless device
configuration but were not available to it before:
- HT/VHT capabilities and capabilities masks.
- full channel info (not just IEEE number)
- BSSID hint
- previous BSSID for reassoc request
Move Management Frame Protection setting from common encr info
structure into STA-specific .connect command parameters.
Make sure that all new qlink structure definitions are alignment-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Include HT/VHT caps directly into command so that they won't have
to be searched for in IEs.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current logic artificially divides "start AP" procedure into three
stages:
- generic interface configuration (security, channel etc)
- IE's processing
- enable AP mode on interface
This separation would not allow to do a proper device configuration as
first stage needs to use information from IEs that are processed on
a second stage. Which means first and second stages have to be meged.
In that case there is no point anymore to keep third stage either, so
merge all three into a single command.
This new command carries all the same info as contained in
"struct cfg80211_ap_settings".
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data contained within "Append IEs" command (QLINK_CMD_MGMT_SET_APPIE)
duplicates QTN_TLV_ID_IE_SET TLV. Convert the command to use that TLV
instead.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"IE set" TLV carries the same information as
qlink_event_scan_result::frame_type. Convert the event to make use of
TLV and drop frame_type member.
While at it, make qlink_event_scan_result structure alignement-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifying frame type for "IE set" TLV will allow to use several
TLVs in a single message.
Modify users accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Supported WiFi operation modes are now identified per-band based on
HT/VHT capabilities of each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Information on which HT/VHT capabilities can be overridden is reported
per-MAC by wireless device.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HT/VHT capabilities must be reported per each band supported by a radio,
not for all bands on a radio. Furthermore, driver better not assume
any capabilities and just use whetever is reported by device itself.
To support this, convert "get channels" command into "get band info"
command. Difference is that it may also carry HT/VHT capabilities along
with channels information.
While at it, also add "num_bitrates" field to "get band info" command,
for future use.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The configuration of the IEs for probe requests was done in a P2P
related function, which is not very obvious. Moving it to
.scan callback function, ie. brcmf_cfg80211_scan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field struct brcmf_cfg80211_info::active_scan is set to true upon
initializing the driver instance, but it is never changed so simply
get rid of it.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_cfg80211_escan() is only called by brcmf_cfg80211_scan()
so there is no reason to split in two function especially since the latter
does not do an awful lot.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Minor cleanup using provided macro to convert milliseconds interval
to jiffies in brcmf_cfg80211_escan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_cfg80211_escan() was always called with a non-null
request parameter and null pointer for this_ssid parameter. Clean up
the function removing the dead code path.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disable arp and nd offload to allow all packets sending to host.
Reported-by: Phil Elwell <phil@raspberrypi.org>
Tested-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware uses a mailbox to communicate to the host what is going
on. In the driver we validate the bit received. Various people seen
the following message:
brcmfmac: brcmf_sdio_hostmail: Unknown mailbox data content: 0x40012
Bit 4 is cause of this message, but this actually indicates the firmware
has halted. Handle this bit by giving a more meaningful error message.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable framelen is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/zydas/zd1201.c:234:3: warning: Value stored
to 'framelen' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The pointer dev is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/intersil/orinoco/orinoco_usb.c:1468:2: warning:
Value stored to 'dev' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer sta_priv is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2163:2: warning: Value
stored to 'sta_priv' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cfg_cmd is initialized to zero and this value is never read, instead
it is over-written in the start of a do-while loop. Remove the
redundant initialization. Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/core.c:1750:22: warning: Value
stored to 'cfg_cmd' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
tid_data is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/base.c:1581:2: warning: Value
stored to 'tid_data' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The calculation of ppsc->last_wakeup_time is not y2038-safe, but
the variable is not used at all, so we can simply drop it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
do_gettimeofday() is deprecated and slower than necessary for the purpose
of reading the seconds. This changes rtl_op_suspend/resume to use
ktime_get_real_seconds() instead, which is simpler and avoids confusion
about whether it is y2038-safe or not.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We set rtlhal->last_suspend_sec to an uninitialized stack variable,
but unfortunately gcc never warned about this, I only found it
while working on another patch. I opened a gcc bug for this.
Presumably the value of rtlhal->last_suspend_sec is not all that
important, but it does get used, so we probably want the
patch backported to stable kernels.
Cc: stable@vger.kernel.org
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82839
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822be checks H2CQ by int_d, so we extend to four ISR.
Also, irq_mask is extended to four.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver for the RTL8822BE is added, it will need an ID for
further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the RTL8822BE, an H2C tx queue is added to download FW and special
data. This change implements the support code in rtl_pci.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of TX/RX BD desc for 8822BE is 512.
The TX/RX BD architecture of 8822BE is the same as 8192EE.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In several places, the code assigns a variable inside an "if" or "case"
block, but uses it only once. The code is simplified by eliminating
the extraneous variable. With this change, one level of indenting is
saved.
This patch does not cause any functional changes in the binary code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of formatting problems in this source
file. None of the changes cause any functional changes in the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of formatting problems in this header
file. None of the changes cause any functional changes in the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
-----BEGIN PGP SIGNATURE-----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=CC8e
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi updates
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a hardware restart the BA session data in HW is lost
so the reorder buffer simply passes the frames to mac80211 as is
as there is no NSSN set. Instead, we will drop these frames
before they reach the reorder buffer. mac80211 drops such frames anyway,
but we shouldn't rely on that. In addition it saves some
processing time
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
The RCU lifetime on baid_data is unclear, so this adds a direct copy of the
rcu_ptr passed to the original callback. It may be possible to improve this
to just use baid_data->mvm->baid_map[baid_data->baid] instead.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_flush_tx_path() function sends a synchronous command to
the firmware. When doing that, we must hold the mutex. The
iwl_mvm_flush_no_vif() function was mistakenly not holding the mutex.
Fix it.
Fixes: 6110d9e5bd ("iwlwifi: mvm: Flush non STA TX queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the mac flush flow, we should flush all existing queues.
Since FW API for a000 devices is flush per RA-TID, simply
flush all stations with all tids.
From FW perspective, asking to flush a TID that doesn't have
a queue is valid, so we can just set all bits in the TID mask.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is very indented and hard to read.
Refactor it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we return early from sync_rx_queues for a000 devices.
This may cause, in case of a non-empty reorder buffer, a warning
later on since the RX queue isn't getting the notification to
empty it.
A better approach would be to send the notification for the default
queue only.
Do this hard coded for now, until we will have the API to enable
multi queue for a000 devices.
Fixes: bc02946964 ("iwlwifi: mvm: disable RX queue notification for a000 devices")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit a6d24fad00 ("iwlwifi: pcie: dump registers when HW becomes
inaccessible") added a function to dump pcie config registers and
memory mapped registers on a failure. It is currently only accessible
within trans.c. Add it to struct iwl_trans_ops, so that failure cases
in other files can call it. While there, add a call to this function
from iwl_pcie_load_firmware_chunk in pcie/tx.c, since this is a common
failure case seen on some platforms.
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
[modified the commit message slightly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This was used for internal devices that are now deprecated.
All the currently existing devices can do paging without
any help from the host.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We had a bunch of code that was relevant for internal
devices only. Those devices are now being depreceated.
Kill all the now unneeded code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When there is a reorder timeout, we may get to a situation
where we have the timeout latency for all the next 64 frames.
This happens since NSSN is behind for a while, and the driver
won't release the frames, since it is not allowed by NSSN.
As a result the frame is stored in the reorder buffer although
there is no hole, and released 100 ms later.
Add a direct comparison to the reorder buffer head, and release
immediately if possible.
For example:
Frame 0 is missed. We receive frame 1, and store it in the buffer.
After 100 ms, frame 1 is released and reorder buffer head is 2.
We then receive frame 2, with NSSN 0, and store it instead of
releasing it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't plan to have products with 3 antennas in the near
future. All the rest of the code follows the same
assumption as well.
Remove the support for antenna C from rs_toggle_ant.
When trying to toggle from ANT_B, this avoids to go through
ANT_C, discover that it doesn't exist and continue to ANT_A.
In MIMO, this avoids to do ANT_AB -> ANT_BC -> ANT_AC and
back to ANT_AB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After a FW reset on A000 NICs, the driver doesn't
set the seq number when re-allocating the queues.
This in turn leads to a mismatch between the seq
number the driver thinks each frame has, and the
actual seq num given by the HW.
This especially causes issues with aggregations,
since the driver could be waiting to start an
aggregation and queue traffic from the mac80211
until then, when actually it shouldn't be waiting.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the code is mixing defines and is inconsistent.
When enabling a queue, we usually configure the scheduler
with IWL_FRAME_LIMIT - 64.
When sending to firmware the rate scaling, we limit aggregation
to LINK_QUAL_AGG_FRAME_LIMIT_DEF - 63, due to a scheduler bug.
Given that, clean up the following:
- Fix a stray queue enablement with LINK_QUAL_AGG_FRAME_LIMIT_DEF.
- Change the comparison that tests if queue needs to be reconfigured
to be compared directly to how it was configured.
This also saves the redundant round down of the buffer size just
for the sake of comparing it, making the code more readable.
- Better document gen2 logic
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a macro for converting TX response rate to a
rate scale value, use it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some wowlan related code was outside CONFIG_PM flag which caused these
build errors. They are fixed by moving that code under CONFIG_PM flag.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ef71ed0608c ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Fixes: a24e35fcee0 ("rsi: sdio: Add WOWLAN support for S4 hibernate state")
Fixes: e1ced6422a3 ("rsi: sdio: add WOWLAN support for S3 suspend state")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic. It doesn't contain wowlan specific code.
It should not be under CONFIG_PM. This patch resolves compilation
errors observed when CONFIG_PM flag is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ef71ed0608c ("rsi: sdio: Add WOWLAN support for S5 shutdown state")
Fixes: a24e35fcee0 ("rsi: sdio: Add WOWLAN support for S4 hibernate state")
Fixes: e1ced6422a3 ("rsi: sdio: add WOWLAN support for S3 suspend state")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git fixes for 4.14. Major changes:
ath10k
* fix security vulnerability with missing PN check on certain hardware
* revert ath10k napi fix as it caused regressions on QCA6174
wcn36xx
* remove unnecessary rcu_read_unlock() from error path
Wireless device may implement a logic to kick-out STA due to inactivity
for a certain period of time. This feature needs to be advertised to
higher layers if supported. Timeout value is still taken from
parameters to START_AP command, nothing changes here.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current recovery approach is to wake s/w Tx queues for skb->dev netdevice.
However this approach doesn't cover the case when h/w queue is full of
packets from a single wireless interface. Suppose xmit attempt from the
second wireless interface fails due to failed reclaim. Then the second
interface will not have a chance to recover even if subsequent reclaims
succeed. Possible solution is to attempt to wake all the s/w queues
belonging to driver interfaces.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function qtnf_classify_skb_no_mbss has been used for debug
during early stage of development. Drop its declaration.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support registration for more mgmt frame types
for debug and monitoring purposes.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Under heavy load it is normal that h/w Tx queue is almost full all the time
and reclaim should be done before transmitting next packet. Warning still
should be reported as well as s/w Tx queues should be stopped in the
case when reclaim failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unlike other power states, WoWLAN configuration does not come from
mac80211 for shutdown. Hence configuring the WoWLAN from shut down
callback it self. Remaining steps of disabling SDIO interrupts,
setting 'MMC_PM_KEEP_POWER' flag are same as other power states.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We are disabling of interrupts from firmware in freeze handler.
Also setting power management capability KEEP_MMC_POWER to make
device wakeup for WoWLAN trigger.
At restore, we observed a device reset on some platforms. Hence
reloading of firmware and device initialization is performed.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WoWLAN is supported in RS9113 device through GPIO pin2.
wowlan config frame is internally sent to firmware in mac80211
suspend handler. Also beacon miss threshold and keep-alive time
values are increased to avoid un-necessary disconnection with AP.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver is transmitting in 11N rates, when connected to an AP in
TKIP security mode. Add a check to disable_11n to fix the issue.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When joining an IBSS network, wdev->ssid/_len will already be
set, so there's no need to write them. In any case, they are
internal cfg80211 values, and have very little user-visible
impact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thorsten reported on <fa6e3ee2-91b5-a54b-afe3-87f30aac7a48@leemhuis.info> that
commit c9353bf483 made ath10k unstable with QCA6174 on his Dell XPS13 (9360)
with an error message:
ath10k_pci 0000:3a:00.0: failed to extract amsdu: -11
It only seemed to happen with certain APs, not all, but when it happened the
only way to get ath10k working was to switch the wifi off and on with a hotkey.
As this commit made things even worse (a warning vs breaking the whole
connection) let's revert the commit for now and while the issue is being fixed.
Link: http://lists.infradead.org/pipermail/ath10k/2017-October/010227.html
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and
HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done
on host (mac80211) rather than firmware. Rebuild cipher header
in every received data frames (that are notified through those
HTT interfaces) from the rx_hdr_status tlv available in the
rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED
flag for the packets which requires mac80211 PN/TSC check support
and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X,
QCA9887, QCA99X0, QCA9984, QCA9888 and QCA4019 currently need the
rebuilding of cipher header to perform PN/TSC check for replay
attack.
Please note that removing crypto tail for CCMP-256, GCMP and GCMP-256 ciphers
in raw mode needs to be fixed. Since Rx with these ciphers in raw
mode does not work in the current form even without this patch and
removing crypto tail for these chipers needs clean up, raw mode related
issues in CCMP-256, GCMP and GCMP-256 can be addressed in follow up
patches.
Tested-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No rcu_read_lock is called, but rcu_read_unlock is still called.
Thus rcu_read_unlock should be removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This driver shouldn't be using wdev->ssid to start with, as
it's more or less an internal field in cfg80211 used for
various purposes. Reading it is possible through nl80211,
even if that's not really what we should be doing there
for anything but AP type interfaces.
It *really* shouldn't allow modifying it!
Remove the whole debugfs entry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable val is unsigned, so checking whether it is less than zero is
redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Variable val is unsigned, so checking whether it is less than zero is
redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current firmware 10.4-3.5.1-00035 on QCA9888 supports
TDLS explicit mode, it expects WMI_TDLS_ENABLE_PASSIVE
for tdls setup and WMI_TDLS_DISABLE for tdls teardown.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Do not allow off channel operations like scans/roc when
there are active TDLS sessions.
The Current firmware 10.4-3.5.1-00035 on QCA9888 does not
supports any offchannel operations on active TDLS sessions,
either driver needs to block the offchannel operation requests
or should teardown the TDLS connection.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To be able to use ath10k_mac_tdls_vif_stations_count() in
ath10k_hw_scan() in the following patch, move the functions
earlier in the file.
This commit is pure code move, no functional changes.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Build errors have been reported with CONFIG_PM=n:
drivers/net/wireless/ath/ath10k/pci.c:3416:8: error: implicit
declaration of function 'ath10k_pci_suspend'
[-Werror=implicit-function-declaration]
drivers/net/wireless/ath/ath10k/pci.c:3428:8: error: implicit
declaration of function 'ath10k_pci_resume'
[-Werror=implicit-function-declaration]
These are caused by the combination of the following two commits:
6af1de2e4e ("ath10k: mark PM functions as __maybe_unused")
96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but
disabled")
Both build fine on their own.
But now that ath10k_pci_pm_{suspend,resume}() is compiled
unconditionally, we should also compile ath10k_pci_{suspend,resume}()
unconditionally.
And drop the #ifdef around ath10k_pci_hif_{suspend,resume}() too; they
are trivial (empty), so we're not saving much space by compiling them
out. And the alternatives would be to sprinkle more __maybe_unused, or
spread the #ifdef's further.
Build tested with the following combinations:
CONFIG_PM=y && CONFIG_PM_SLEEP=y
CONFIG_PM=y && CONFIG_PM_SLEEP=n
CONFIG_PM=n
Fixes: 96378bd2c6 ("ath10k: fix core PCI suspend when WoWLAN is supported but disabled")
Fixes: 096ad2a15fd8 ("Merge branch 'ath-next'")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.15. Major changes:
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
there it's supported (QCA99x0 and QCA4019)
Since mac80211 maintains the sequence number for each STA/TID,
driver doesn't need to maintain a copy.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the previous commit I left the indentation alone to help reviewing
the patch, this one now runs the three new functions through 'indent -kr -8'
with some manual fixups to avoid silliness.
No changes other than whitespace are intended here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The stack consumption in this driver is still relatively high, with one
remaining warning if the warning level is lowered to 1536 bytes:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:17135:1: error: the frame size of 1880 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]
The affected function is actually a collection of three separate implementations,
and each of them is fairly large by itself. Splitting them up is done easily
and improves readability at the same time.
I'm leaving the original indentation to make the review easier.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Zaborowski <andrew.zaborowski@intel.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Zaborowski <andrew.zaborowski@intel.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Solomon Peachy <pizza@shaftnet.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Igor Mitsyanko <imitsyanko@quantenna.com>
Cc: Avinash Patil <avinashp@quantenna.com>
Cc: Sergey Matyukevich <smatyukevich@quantenna.com>
Cc: Kamlesh Rath <krath@quantenna.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* Allocate reorder buffer dynamically to save memory;
* Fix a FW dump problem in the A000 family;
* Fix for a statistics gathering issue (v2);
* Sort the list of 9000 devices to make it easier to find entries;
* A couple of cleanups in the FW dump code;
* Remove some unnecessary variables and fields and calculations;
-----BEGIN PGP SIGNATURE-----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=JcBj
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second batch of iwlwifi patches for 4.15
* Allocate reorder buffer dynamically to save memory;
* Fix a FW dump problem in the A000 family;
* Fix for a statistics gathering issue (v2);
* Sort the list of 9000 devices to make it easier to find entries;
* A couple of cleanups in the FW dump code;
* Remove some unnecessary variables and fields and calculations;
The first pull request for 4.15, unusually late this time but still
relatively small. Also includes merge from wireless-drivers to fix
conflicts in iwlwifi.
Major changes:
rsi
* add P2P mode support
* sdio suspend and resume support
iwlwifi
* A fix and an addition for PCI devices for the A000 family
* Dump PCI registers when an error occurs, to make it easier to debug
rtlwifi
* add support for 64 bit DMA, enabled with a module parameter
* add module parameter to enable ASPM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ5x32AAoJEG4XJFUm622b22EIAKmIlD1tAXxK9YAtYE5AnD5A
QpklYuVJA4XFtpN9UKXP/KCGTRnflW6i4RQ3dt6WKNULkL8RMAjwDijxXrFz8YXw
uB1Aw+Rbmx8eSrWKTgBCLlfU4J3j8jj5gSc7rzYeG7DnMFVShRCxRChiR09GhY4n
gXX3p4+migW128EyQ4KYYFGxipS+5/0igsSwqE6UIyxDuhINjCS9MipwXmv2uG+G
eYOSlwPE+LI8rObqlaJKVgam77srQqZLnPnima+bKAYXiQOPxPDBLwGP1qjo38Wa
pHKDG//OPMOjyUccl5axulnvLPTjyng9jYNpzJlLLz9+M29SudtHI7YQQHhBj5M=
=bApF
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
The first pull request for 4.15, unusually late this time but still
relatively small. Also includes merge from wireless-drivers to fix
conflicts in iwlwifi.
Major changes:
rsi
* add P2P mode support
* sdio suspend and resume support
iwlwifi
* A fix and an addition for PCI devices for the A000 family
* Dump PCI registers when an error occurs, to make it easier to debug
rtlwifi
* add support for 64 bit DMA, enabled with a module parameter
* add module parameter to enable ASPM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Solomon Peachy <pizza@shaftnet.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is never used, so remove the code to set it.
After this, the variable 'iph' also has the same fate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's hard to find values that are missing in the list, so sorting the
values and comparing them makes it much easier. To simplify this
task, sort the devices in the list.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the compressed BA notif, the driver didn't parse out
the LQ color, so statistics for the rates tried were
always thrown out. Add it so it gets correctly used.
While at it, fix the name of the relevant field in the
struct.
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now have two different minimum valid values for
umac_error_event_table. To avoid hardcoding the minimum value in the
driver, add a value to cfg where it can be read from.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in checking the validity of the
umac_error_event_table pointer every time we generate a dump. It's
cleaner to do so when we read the value, namely when we receive the
alive data.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, UMAC error data reading is restricted to DCCM.
A000 NICs use SMEM for this data.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All callers of iwl_mvm_release_frames() already have the baid_data
pointer, so we don't need to (re)calculate it inside the function.
Just pass it instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reason station id and tid fields are both in baid data and
in the reorder buffer per queue is that we couldn't access the
baid_data in the reorder timer functions.
Now that we do some pointer math and access it anyway, those
fields can be removed.
This save some space and some code.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we may have up to 256 entries per reorder buffer, and possibly up
to 16 queues, we can use a LOT of memory for this (64k for each station).
Allocate it according to what we need, which is of course much less for HT
stations (only 16k at a max of 16 queues).
However, this comes at the expense of complicating the code a bit to
calculate the right entry structure to use for each frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The kbuild test robot reports two conditions with no effect (if == else).
These are the result of copy and paste typographical errors.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: kbuild-all@01.org
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This way, we can apply the values when the NIC does come up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the user sets count to zero the string buffer would remain
completely uninitialized which causes the kernel to parse its
own stack data, potentially leading to an info leak. In addition
to that, the string might be not terminated properly when the
user data does not contain a 0-terminator.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99x0 and QCA4019 family chips support CCMP-256, GCMP-128, and
GCMP-256 ciphers in hardware, so advertise support for these. As
firmware does not support group management frame ciphers (BIP),
handle them in software (mac80211).
Reviewed-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k host enables power save support in station mode by
default for all firmwares but Power save for station mode still not supported
in some of the firmware versions. Which results in firmware crash while
issueing multiple scan commands.
Fix this problem by introducing new FW feature flag to check power save
support in firmware and then the firmware image can tell to ath10k that power
save mode is not supported in station mode.
Signed-off-by: Venkateswara Naralasetty <vnaralas@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices where the FW supports WoWLAN but user-space has not
configured it, we don't do any PCI-specific suspend/resume operations,
because mac80211 doesn't call drv_suspend() when !wowlan. This has
particularly bad effects for some platforms, because we don't stop the
power-save timer, and if this timer goes off after the PCI controller
has suspended the link, Bad Things will happen.
Commit 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
got some of this right, in that it understood there was a problem on
non-WoWLAN firmware. But it forgot the $subject case.
Fix this by moving all the PCI driver suspend/resume logic exclusively
into the driver PM hooks. This shouldn't affect WoWLAN support much
(this just gets executed later on).
I would just as well kill the entirety of ath10k_hif_suspend(), as it's
not even implemented on the USB or SDIO drivers. I expect that we don't
need the callback, except to return "supported" (i.e., 0) or "not
supported" (i.e., -EOPNOTSUPP).
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Fixes: 77258d409c ("ath10k: enable pci soc powersaving")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Cc: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
gcc produces a harmless warning about a recently introduced
signed integer overflow:
drivers/net/wireless/rsi/rsi_91x_hal.c: In function 'rsi_prepare_mgmt_desc':
include/uapi/linux/swab.h:13:15: error: integer overflow in expression [-Werror=overflow]
(((__u16)(x) & (__u16)0x00ffU) << 8) | \
~~~~~~~~~~~~^~~~~~~~~~~~~~~~~
include/uapi/linux/swab.h:104:2: note: in expansion of macro '___constant_swab16'
___constant_swab16(x) : \
^~~~~~~~~~~~~~~~~~
include/uapi/linux/byteorder/big_endian.h:34:43: note: in expansion of macro '__swab16'
#define __cpu_to_le16(x) ((__force __le16)__swab16((x)))
^~~~~~~~
include/linux/byteorder/generic.h:89:21: note: in expansion of macro '__cpu_to_le16'
#define cpu_to_le16 __cpu_to_le16
^~~~~~~~~~~~~
drivers/net/wireless/rsi/rsi_91x_hal.c:136:3: note: in expansion of macro 'cpu_to_le16'
cpu_to_le16((tx_params->vap_id << RSI_DESC_VAP_ID_OFST) &
^~~~~~~~~~~
The problem is that the 'mask' value is a signed integer that gets
turned into a negative number when truncated to 16 bits. Making it
an unsigned constant avoids this.
Fixes: eac4eed322 ("rsi: tx and rx path enhancements for p2p mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linux Wireless device structure already has current channel
information that can be used when needed. Start using it.
Since driver's channel info is not used anymore, remove it.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Encryption info is a constant part of STA settings, no point
to pass it as an optional TLV.
Remove QTN_TLV_ID_CRYPTO type as it's not used anymore.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This cached state is used only once immediately after it is
initilized, except for BSSID value that is used for events processing.
There is no reason in keeping unused data in driver's state.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QTNF_STATE_AP_START usage is redundant and imposes additional state
synchronization maintenance. We may as well leave state checking
to network card and upper layers (cfg80211, nl80211 and userspace).
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
QTNF_STATE_AP_CONFIG is redundant and its usage can be safely removed.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce "channel definition" TLV containing full channel
description (center frequence for both segments + BW) and pass it to
wireless card in a payload to START_AP command.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify QLINK START_AP command payload to pass all AP settings
contained within struct cfg80211_ap_settings.
Make most of settings a constant part of "config AP" command
instead of passing it as an optional TLVs.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cached AP setings are passed to WiFi card right after they are
initialized and are never used for anything else. There is no
point in keeping them in driver state.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clean up unused cur_rfstate variables in rtl8188ee, rtl8723ae, rtl8723be
and rtl8821ae.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some platforms, enable ASPM will cause AER error to be logged, thus
we use a parameter to selectively turn on ASPM.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
- Add new parameter "is_bw_update" to control if current bandwidth setting
is updated to FW RA.
- After this commit, we keep the same setting as before.
- Later, bandwidth update in watchdog is changed to false for 8822BE.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These fields are unused, and we will define them in phydm later.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These definition will be used by phydm later.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The statistic variables use u64 to get higher precision.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Convert from the value of ieee80211_tx_queue_params to Realtek's
register value.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally, we get legacy rate only, so we extend to get HT and VHT rate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Both 32-bit and 64-bit use the same TX/RX buffer desc layout
2. Extend set_desc() and get_desc() to set and get 64-bit address
3. Remove directive DMA_IS_64BIT
4. Add module parameter to turn on 64-bit dma
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The semicolon can cause compiler error, if it exists in if...else
statement.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We must choose only one of VHT_CAP among
IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_3895,
IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_7991 and
IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_11454.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use put_unaligned_le32 rather than using byte ordering function and
memcpy which makes code clear.
Also, add the header file where it is declared.
Done using Coccinelle and semantic patch used is :
@ rule1 @
identifier tmp; expression ptr,x; type T;
@@
- tmp = cpu_to_le32(x);
<+... when != tmp
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_le32(x,ptr);
...+>
@ depends on rule1 @
type j; identifier tmp;
@@
- j tmp;
...when != tmp
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a user requests scan, driver sends multiple scan requests
to firmware, which might be active or passive. Firmware will
send channel statistics for each channel in the request. This will
be stored in chan_stats array.
Few channels might report hidden SSIDs in passive scan results.
So, once the original scan request is finished, driver issues an
active scan request for all channels which reported hidden SSIDs.
This will cause duplicates in the chan_stats array. At worst,
every channel will have a hidden SSID, in which case the driver
can issue active scan requests for each channel. So the complete
scan statistics size will be twice of existing limit.
At present maximum number of channels returned in scan statistics
is 31(BG) + 14(A) = 45. Clearly there will be an overflow of the
chan_stats array in the above mentioned scenario. To fix this
double the size of chan_stats array.
Signed-off-by: Rohit Fule <rohitf@marvell.com>
Signed-off-by: Mangesh Malusare <mmangesh@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The sta_list_spinlock looks to be used to control locking of the
list. Specifically when someone has the lock they may be allowed
to modify or delete elements of the list.
That implies that we shouldn't access the fields of the elements
returned by mwifiex_get_sta_entry() after we've released the
spinlock. Let's make some small changes so this is true.
It's unlikely that this matters since it looks to be just error
handling, but it's nice to be clean.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's absolutely no reason to check to see if a list is empty
before iterating through it. It's just like writing code like
this:
if (count != 0) {
for (i = 0; i < count; i++) {
...
}
}
The loop will already be avoided if "count == 0" so there was no
reason to check.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Cleanups: - remove an unused value that we read from the NVM;
- remove link quality measurement code that was never used;
* One FW command API update;
* A fix and an addition for PCI devices for the A000 family;
* Tiny refactor of ref/unref code used by runtime-PM;
* Some debugging improvements;
* Implementation of a more flexible way to define command queue sizes;
* ACPI code refactoring;
* Some coding-style fixes;
* Avoid redundant command to the firmware;
* Add a struct with the format of one FW command;
* Change an error log to a warning when the FW API is not aligned with
the driver (important during development);
* Change a WARN_ON to WARN_ONCE to make it more descriptive and less
noisy (i.e. no repeated warnings on a firmware triggered error);
* Dump PCI registers when an error occurs, to make it easier to debug;
-----BEGIN PGP SIGNATURE-----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=wHeE
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-10-06-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi patches for 4.15 (v2)
* Cleanups: - remove an unused value that we read from the NVM;
- remove link quality measurement code that was never used;
* One FW command API update;
* A fix and an addition for PCI devices for the A000 family;
* Tiny refactor of ref/unref code used by runtime-PM;
* Some debugging improvements;
* Implementation of a more flexible way to define command queue sizes;
* ACPI code refactoring;
* Some coding-style fixes;
* Avoid redundant command to the firmware;
* Add a struct with the format of one FW command;
* Change an error log to a warning when the FW API is not aligned with
the driver (important during development);
* Change a WARN_ON to WARN_ONCE to make it more descriptive and less
noisy (i.e. no repeated warnings on a firmware triggered error);
* Dump PCI registers when an error occurs, to make it easier to debug;
Driver will advertise RANDOM_MAC support only if the device
supports this feature.
Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My static checker complains that we have an upper bound but no lower
bound. I suspect neither are really required but it doesn't hurt to add
a check for negatives.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The default power limit read from the SPLC method in ACPI doesn't
have anything to do with the transport and is only used in the opmode,
so we can remove it from the trans. Additionally, this value is only
user when the opmode is starting, so we don't need to store it
anywhere.
Remove the dflt_pwr_limit element from the trans and move call to
iwl_acpi_get_pwr_limit() call to mvm.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the wrong statistics size is a problem, having a warning
will help us catch it quicker during firmware/driver development.
In released firmware/driver versions, we obviously make sure this
won't happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move most of the set_dflt_pwr_limit() function to acpi.c and make it
return the pwr_limit value instead of setting directly. Also rename
it to iwl_acpi_get_pwr_limit().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the double indentation in the configuration structs
for a000 family devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_get_bios_mcc() function was in the iwl-nvm-parse.c file, but
it has nothing to do with the NVM. Move it to fw/acpi.c and rename it
to iwl_acpi_get_mcc().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The way iwl_get_bios_mcc() gets the WiFi package and checks for its
integrity is almost identical to the new iwl_acpi_get_wifi_pkg()
function. Instead of having duplicate code, convert it to use the
common code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of finding the wifi package with its own code, we can reuse
the new iwl_acpi_get_wifi_pkg() function when reading the default
power limit from SPLC.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move this function to acpi.c, renaming it to iwl_acpi_get_wifi_pkg(),
because it can also be used with other methods (i.e. SPLC and WRDD).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ACPI table size definitions were spread around the different files
that used them. Move them all to a common place.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of defining each method where they are used and re-defining
WIFI_DOMAIN in each one of them, move all the definitions to a central
place and define the domain only a single time.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are many places where the same process of invoking a method from
ACPI is used, causing a lot of duplicate code. To improve this,
introduce a new function to get an ACPI object by invoking an ACPI
method that can be reused.
Additionally, since this function needs to be called when we only have
the trans, the opmode or the device, introduce a new debug macro that
gets the device as a parameter so it can be used in the new function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there is a FW bug where the BAID value in the
metadata is not properly initialized we hit the warning for
every RX packet.
Change it to warn once and add elaborate message.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We conclude the HW became inaccessible when we timeout waiting for
a bit to be set in a memory mapped register (CSR_GP_CNTRL). This
conclusion may not be true because the bit may not get set due to:
- a firmware issue
- a driver issue
- a PCI bus issue
- a platform issue
There are a lot of such reports with really no good debug information
beyond this message to help us.
Add some debug information and attempt to dump the different register
spaces at such a failure:
* Dump some configuration space of device - this will tell us if
something very basic is broken in the PCIe bus (so that configuration
accesses are failing). If this works, the PCIe bus seems OK. If this
does not work, it is definitely an PCIe issue.
* Dump some memory mapped registers - if we're reading some sane'ish
values, this will tell us that the PCIe bus is OK, but may be a firmware
/ driver issue. If this does not work, it may be a PCI configuration
issue or a driver/firmware issue.
* Dump parent and device's AER registers, will give us some straws to
chew on.
This is the sample output:
[ 13.082651] ------------[ cut here ]------------
[ 13.086791] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
[ 13.086793] iwlwifi 0000:01:00.0: iwlwifi device config registers:
[ 13.086893] iwlwifi 0000:01:00.0: 00000000: 095a8086 00100406 02800059 00000000 00000004 00000000 00000000 00000000
[ 13.086895] iwlwifi 0000:01:00.0: 00000020: 00000000 00000000 00000000 50108086 00000000 000000c8 00000000 00000100
[ 13.086901] iwlwifi 0000:01:00.0: iwlwifi device memory mapped registers:
[ 13.086989] iwlwifi 0000:01:00.0: 00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086991] iwlwifi 0000:01:00.0: 00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086999] iwlwifi 0000:01:00.0: iwlwifi device AER capability structure:
[ 13.087033] iwlwifi 0000:01:00.0: 00000000: 14010001 00100000 00000000 00462031 00002000 00002000 00000014 40000001
[ 13.087034] iwlwifi 0000:01:00.0: 00000020: 0000000f d140000c 00000000
[ 13.087036] iwlwifi 0000:01:00.0: iwlwifi parent port (0000:00:1c.0) config registers:
[ 13.087074] iwlwifi 0000:00:1c.0: 00000000: 9d108086 00100506 060400f1 00810010 00000000 00000000 00010100 200000f0
[ 13.087075] iwlwifi 0000:00:1c.0: 00000020: d140d140 0001fff1 00000000 00000000 00000000 00000040 00000000 0006010b
[ 13.087087] ------------[ cut here ]------------
[ 13.087095] WARNING: CPU: 0 PID: 1759 at drivers/net/wireless/iwl7000/iwlwifi/pcie/trans.c:2082 iwl_trans_pcie_reclaim+0x1ee4/0x2b9a [iwlwifi]()
[ 13.087096] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes three trivial issues as reported by checkpatch.pl, namely two
switch/case indentation issues and one alignment issue in a multiline
comment.
Signed-off-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This helps for documentation and clarifies the code by defining the
exact response struct for the marker command.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These enum values don't exist, so remove their documentation as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have an AP which supports HT and a single HT
station is connected, we change the min_width from
NL80211_CHAN_WIDTH_20_NOHT to NL80211_CHAN_WIDTH_20. This
of course has no implication on the channel width but still
sends a command to the firmware.
Remember the last width that was sent and refrain from
sending unnecessary commands to the firmware.
Sending a PHY_CTXT_CMD to the firmware has a cost since it
recalculates the presence on the medium and because of that
it closes the transmit queues for a short while.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver reads xtal_calib from NVM file, but actually never uses it.
This is only used in dvm driver.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Devices in the A000 family can use a different size for the command queue.
To allow this, make the command queue size configurable and set the size
for A000 devices to 32.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This would enable to better catch timing issues with
cases that WRT dump takes too much time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger that collects data when a frame is released
because of the timer of the reordering buffer was not
implemented for 9000 devices.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This was never used by any product. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New quota command adds a field indicating low latency
direction per quota.
A TLV API bit was added to indicate the new API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new a000 device with PCI ID (0x2720, 0x0030).
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCI ID (0x2720, 0x0070) was set with the config struct
iwla000_2ax_cfg_hr instead of iwla000_2ac_cfg_hr_cdb.
Fixes: 175b87c692 ("iwlwifi: add the new a000_2ax series")
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
De-inline iwl_trans_ref/unref and move it to common transport code
in preparation for more common code to come to these functions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a dbgfs entry for an easy way during runtime to
check what FW file was loaded, and get some general
FW-related data.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver currently handles two NVM formats,
one for 7000 family and below, and one for 8000 family and above.
The 3168 series uses something in between,
so currently the driver uses incorrect offsets for it.
Fix the incorrect offsets.
Fixes: c4836b056d ("iwlwifi: Add PCI IDs for the new 3168 series")
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current channel flags printing is very strange and messy,
in LAR we sometimes print the channel number and sometimes the
frequency, in both we print a calculated value (whether ad-hoc
is supported or not) etc.
Unify all this to
* print the channel number, not the frequency
* remove the band print (2.4/5.2 GHz, it's obvious)
* remove the calculated Ad-Hoc print
Doing all of this also gets the length of the string to a max
of 101 characters, which is below the max of 110 for tracing,
and thus avoids the warning that came up on certain channels
with certain flag combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It seems that libsensors treats -EIO as a special non-recoverable
failure when it tries to read the temperature while the firmware is
not running. To solve that, change the error code to a milder
-ENODATA.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196941
Fixes: c221daf219 ("iwlwifi: mvm: add registration to thermal zone")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today we stop the device and the DMA without stopping the dbgc
recording before. This causes host crashes when the DMA
rate is high.
Stop dbgc recording when clearing the fw debug configuration
to fix this.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In monitor mode we are not expected to decrypt encrypted
packets (not having the keys).
Hence we are expected to get an unknown rx security status.
Keeping the print in monitor mode causes a print for each
captured packet flooding the dmesg.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Merging this brings in the timer_setup() change, which allows
me to apply Kees's mac80211 changes for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't populate the read-only array reg_hole_list on the stack, instead make
it static. Makes the object code smaller by over 200 bytes:
Before:
text data bss dec hex filename
57518 15248 0 72766 11c3e debug.o
After:
text data bss dec hex filename
57218 15344 0 72562 11b72 debug.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
brcmf_fweh_process_event() sets event->datalen to the
endian-swapped value of event_packet->msg.datalen, which is the
same as emsg.datalen. This length is already validated in
brcmf_fweh_process_event(), so there is no need to check it
again upon dequeuing the event.
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_p2p_notify_rx_mgmt_p2p_probereq(), chanspec is assigned before
the length of rxframe is validated. This could lead to uninitialized
data being accessed (but not printed). Since we already have a
perfectly good endian-swapped copy of rxframe->chanspec in ch.chspec,
and ch.chspec is not modified by decchspec(), avoid the extra
assignment and use ch.chspec in the debug print.
Suggested-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With KASAN and a couple of other patches applied, this driver is one
of the few remaining ones that actually use more than 2048 bytes of
kernel stack:
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy_gainctrl':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:16065:1: warning: the frame size of 3264 bytes is larger than 2048 bytes [-Wframe-larger-than=]
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:17138:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Here, I'm reducing the stack size by marking as many local variables as
'static const' as I can without changing the actual code.
This is the first of three patches to improve the stack usage in this
driver. It would be good to have this backported to stabl kernels
to get all drivers in 'allmodconfig' below the 2048 byte limit so
we can turn on the frame warning again globally, but I realize that
the patch is larger than the normal limit for stable backports.
The other two patches do not need to be backported.
Cc: <stable@vger.kernel.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of the data in the received skb is currently passed into
brcmf_fweh_process_event() as packet_len, but this value is not checked.
event_packet should be followed by DATALEN bytes of additional event
data. Ensure that the received packet actually contains at least
DATALEN bytes of additional data, to avoid copying uninitialized memory
into event->data.
Cc: <stable@vger.kernel.org> # v3.8
Suggested-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 40b368af4b ("rtlwifi: Fix alignment issues"), the read
of REG_DBI_READ was changed from 16 to 8 bits. For unknown reasonsi
this change results in reduced stability for the wireless connection.
This regression was located using bisection.
Fixes: 40b368af4b ("rtlwifi: Fix alignment issues")
Reported-and-tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.11+
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate const arrays on the stack, instead make them static.
Makes the object code smaller by over 60 bytes:
Before:
text data bss dec hex filename
14816 1296 0 16112 3ef0 b43/phy_ht.o
After:
text data bss dec hex filename
14551 1496 0 16047 3eaf b43/phy_ht.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate const array ac_to_fifo on the stack in an inlined
function, instead make it static. Makes the object code smaller
by over 800 bytes:
text data bss dec hex filename
159029 33154 1216 193399 2f377 4965-mac.o
text data bss dec hex filename
158122 33250 1216 192588 2f04c 4965-mac.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless device may send "channel changed" event before driver
registered this device with wireless core, which will result in
warnings.
Once device is registered, higher layer will query channel info
manually using .get_channel callback.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are no users of this field and it can safely be removed.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is never used for anything useful, and all logic is handled by
either WiFi card or higher layers.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not assume whether wireless device can or can not handle switching
several interfaces on a single radio to different channels. Device will
handle it itself and will return appropriate error code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No reason to verify channel switch request in driver, it can simply be
forwarded to wireless device. Device can perform required checks and
return appropriate error code, and driver may not even have information
on current operational channel.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes no sense because real operational channel is choosen based
on AP operation, not on what STA is configured to.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not try to cache current operational channel info in driver, this
is a potential source of synchronization issues + driver does not
really need that info.
Introduce GET_CHANNEL command and process it appropriately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifically, it has to report center frequency, secondary center
frequency (for 80+80) and BW.
Introduce channel definition structure to qlink and modify channel
change event processing function accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will allow to use qlink channel width values to specify BW setting
corresponding to enum nl80211_chan_width.
Current user is converted to apply BIT() macro manually to each individual
qlink_channel_width enumeration value.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO suspend and resume handlers are implemented and verified
that device works after suspend/resume cycle.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will dump information about firmware version, firmware file
name and operating mode during initialization.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate the read-only const array tos_to_ac on the stack,
instead make it static. Makes the object code smaller by 250 bytes:
Before:
text data bss dec hex filename
26104 2720 128 28952 7118 wmm.o
After:
text data bss dec hex filename
25758 2816 128 28702 701e wmm.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I assume that a blank efuse comes with all ones, thus I did not bother
recognizing other possible junk values. This matches 100% of dongles
I've seen (a single Gembird 8192eu).
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate const array ucode_ofdm_rates on the stack, instead make it
static. Makes the object code smaller by 100 bytes:
Before:
text data bss dec hex filename
39482 564 0 40046 9c6e phy_cmn.o
After
text data bss dec hex filename
39326 620 0 39946 9c0a phy_cmn.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3620 can only operate on 2.4GHz band due to RF limitation.
If wcn36xx digital block is associated with an external IRIS
RF module, retrieve the id and disable 5GHz band in case of
wcn3620 id.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make them const as they are not modified in the file referencing
them. They are only stored in the const field 'hw_ce_reg' of an ath10k
structure. Also, make the declarations in the header const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
casting to void pointer from any pointer type and vice-versa is done
implicitly and therefore casting is not needed in such a case.
Done using Coccinellle.
Semantic Patch used :
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T *)x)->f
|
- (T *)
e
)
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is disabled, we get a compile-time
warning:
drivers/net/wireless/ath/ath10k/pci.c:3417:12: error: 'ath10k_pci_pm_resume' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/pci.c:3401:12: error: 'ath10k_pci_pm_suspend' defined but not used [-Werror=unused-function]
static int ath10k_pci_pm_suspend(struct device *dev)
Rather than fixing the #ifdef, this just marks both functions
as __maybe_unused, which is a more robust way to do this.
Fixes: 32faa3f0ee ("ath10k: add the PCI PM core suspend/resume ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The mac80211_hwsim doesn't offer a way to disable the debugging output.
Unfortunately, it's pretty chatty, dumping a lot of stuff into the message
buffer.
This patch changes it to use dyndbg for controlling the debug output.
It's disabled by default, but can be enabled by a module parameter (1),
at runtime (2) or persisted in modprobe.conf (3).
(1) modprobe mac80211_hwsim dyndbg=+p
(2) echo "module mac80211_hwsim +p" >/sys/kernel/debug/dynamic_debug/control
(3) echo "options mac80211_hwsim dyndbg=+p" >>/etc/modprobe.d/my.conf
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid calculating random MAC address in driver. Instead make
use of 'get_random_mask_addr()' function.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Application will keep track of whether MAC address randomization
is enabled or not during scan. But at present driver is storing
'random_mac' in mwifiex_private which implies even after scan is
done driver has some reference to the earlier 'scan request'. To
avoid this, make use of 'mac_addr' variable in 'scan_request' to
store 'random_mac'. This structure will be freed by cfg80211 once
scan is done.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate const arrays on the stack, instead make them static
Makes the object code smaller by nearly 300 bytes:
Before:
text data bss dec hex filename
69260 16149 576 85985 14fe1 cfg80211.o
After:
text data bss dec hex filename
68385 16725 576 85686 14eb6 cfg80211.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.
Semantic patch used to resolve this issue:
@@
expression e,e2; constant c;
statement S;
@@
e = kzalloc(e2, c);
if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If driver is loaded with 'mfg_mode' enabled, then the sending
commands are not allowed. So, skip sending commands, to firmware
in mwifiex_add_virtual_intf if 'mfg_mode' is enabled.
Fixes: 7311ea8500 ("mwifiex: fix AP start problem for newly added interface")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver sends a series of scan commands to firmware to serve a
user scan request. If an intermediate scan command fails, driver
aborts the scan but it is not being informed to cfg80211. This
will cause issues in applications performing periodic scans.
Fix this by informing scan abort.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In routine rtl92ee_set_fw_rsvdpagepkt(), the driver allocates an skb, but
never calls rtl_cmd_send_packet(), which will free the buffer. All other
rtlwifi drivers perform this operation correctly.
This problem has been in the driver since it was included in the kernel.
Fortunately, each firmware load only leaks 4 buffers, which likely
explains why it has not previously been detected.
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A typo led to this issue, which was detected with the help of Coccinelle.
In addition to fixing the error, the code is refactored to eliminate an
if statement.
Addresses-Coverity-ID: 1226788
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The u8 char array ret is not being initialized and elements outside
the range start to end contain just garbage values from the stack.
This results in a later scan of the array to read potentially
uninitialized values. Fix this by initializing the array to zero.
This seems to have been an issue since the very first commit.
Detected by CoverityScan CID#139653 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The u8 char array ret is not being initialized and elements outside
the range start to end contain just garbage values from the stack.
This results in a later scan of the array to read potentially
uninitialized values. Fix this by initializing the array to zero.
This seems to have been an issue since the very first commit.
Detected by CoverityScan CID#139652 ("Uninitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The assignment of dev is dereferencing adapter before adapter has
been null checked, potentially leading to a null pointer dereference.
Fix this by simply moving the assignment of dev to a later point
after the sanity null check of adapter.
Detected by CoverityScan CID#1398383 ("Dereference before null check")
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add P2P_GO condition as well when handling BEACON_ENABLE
from mac80211. Also passing 'vif' for auto rate request.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
P2P Go condition is added wherever AP mode is there
in aggregation path.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When AP or P2P GO VAP is running, power save configuration should
be disallowed. To check interface type in power save configuration
'vif' parameters is passed.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data descriptor is updated to include vap_id. TX command frame
key config also updated to include vap_id.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parameter 'vif' is passed to inform_bss_status function to
check the type of vif and to get vap_id.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remain-on-channel and cancel-remain-on-channel are implemented
to support p2p listen phase.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA_OPMODE and AP_OPMODE macros are renamed to RSI_OPMODE_STA
and RSI_OPMODE_AP. New opmodes are added to this list for P2P
support. Mapping of mac80211 interface types to rsi interface
types are added.
Add and remove interface callbacks are handled for P2P mode.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds p2p supported parameters to mac80211 hw and
wiphy structures during mac80211 registration.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cancel active scans and deactivate firmware scan watchdog timer
when wireless interface configuration is changed. The usecases
include wireless interface mode change, interface down,
AP stop, virtual interface removal.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix tx path regression. Lock should be held when queuing packets
to h/w fifos in order to properly handle configurations with
multiple enabled interfaces.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver was not properly configuring firmware with regard to the
type of scan. It always performed an active scan even when user-space
was requesting for passive scan, ie. the scan request was done without
any SSIDs specified.
Cc: stable@vger.kernel.org # v4.0.x
Reported-by: Huang, Jiangyang <Jiangyang.Huang@itron.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon handling the firmware notification for scans the length was
checked properly and may result in corrupting kernel heap memory
due to buffer overruns. This fix addresses CVE-2017-0786.
Cc: stable@vger.kernel.org # v4.0.x
Cc: Kevin Cernekee <cernekee@chromium.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* A couple of bugzilla bugs related to multicast handling;
* Two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems;
* Two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch;
* A fix for buffer reordering in the newly supported 9000 device
family;
* Fix a race when starting aggregation;
* Small fix for a recent patch to wake mac80211 queues;
* Send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save;
-----BEGIN PGP SIGNATURE-----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=DM5q
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-09-15' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
First set of fixes for 4.14
* A couple of bugzilla bugs related to multicast handling;
* Two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems;
* Two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch;
* A fix for buffer reordering in the newly supported 9000 device
family;
* Fix a race when starting aggregation;
* Small fix for a recent patch to wake mac80211 queues;
* Send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save;
Few fixes to regressions introduced in the last one or two releases.
The iwlwifi fix is for a regression reported by Linus.
rtlwifi
* fix two antenna selection related bugs
iwlwifi
* fix regression with older firmwares
brcmfmac
* workaround firmware crash for bcm4345
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZsrqPAAoJEG4XJFUm622bT04IAIR/MiSKo+IJ8wpvzXJ5K7x5
/IzGDoJofqiQHVG0Rc72+0ooFwSe6nxQ3E+OzQM9yLIC8XcjPwd8mqnV4dzF5rIs
Q0ou092eBOVfMZO9EMrZJLuFiItfF8deH+nnYDuQBFsTHVKdkYVltB5JUX98hj6q
SFY7RYgmTcXq7j5H5u7AuDueJu0maHq2eb9t6MvtD06pbyvmh5t6CRsSORinMfff
090mWhPYTgZZqCuVQk9lki2671vgqjqfyr2M0hGWnsQCM+IiXUIptSGPEjwRDGDv
0yePGq750YPVjlMixIHfKEfm446YHp++Yjl/QzYCV3bbCHF5yEAUVoG8Nv3ibxc=
=DL06
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-09-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Few fixes to regressions introduced in the last one or two releases.
The iwlwifi fix is for a regression reported by Linus.
rtlwifi
* fix two antenna selection related bugs
iwlwifi
* fix regression with older firmwares
brcmfmac
* workaround firmware crash for bcm4345
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware feature check introduced for multi-scheduled scan is also
failing for bcm4345 devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The condition to check if reorder buffer ran out of
space is faulty, as it takes into account only the
NSSN.
In case the head SN was too far behind the reorder
buffer should move forward, regardless of the NSSN
status.
This caused the driver to release packets out of order
in some scenarios.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always must set the status to what we consider success before
calling iwl_mvm_send_cmd_status() (also iwl_mvm_send_cmd_pdu_status()
which calls it). Fix a few places where initialization is missing.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always need to initialize the status argument to the success case
before calling iwl_mvm_send_cmd_status() or
iwl_mvm_send_cmd_pdu_status() (which calls the former) otherwise we
may get an uninitialized value back. In this case, we use
ADD_STA_SUCCESS as success.
Fixes: 732d06e9d9 ("iwlwifi: mvm: add station before allocating a queue")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were ignoring the FIF_ALLMULTI flag when setting the multicast
addresses with MCAST_FILTER_CMD. Check if this flag is set and enable
pass_all accordingly. We also need to set the count to 0 if pass_all
is enable so we don't pass addresses to the firmware when not needed
(as doing so causes an assert).
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196741
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MCAST_FILTER_CMD can get quite large when we have many mcast
addresses to set (we support up to 255). So the command should be
send as NOCOPY to prevent a warning caused by too-long commands:
WARNING: CPU: 0 PID: 9700 at /root/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/pcie/tx.c:1550 iwl_pcie_enqueue_hcmd+0x8c7/0xb40 [iwlwifi]
Command MCAST_FILTER_CMD (0x1d0) is too large (328 bytes)
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196743
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_start_mac_queues() takes a bitmap of the queues to wake.
When deferred tx is purged, set the bit of the hw_queue so
the correct queue will be waken up.
Fixes: 7e39a00d59 ("iwlwifi: mvm: start mac queues when deferred tx frames are purged")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new state to enum iwl_mvm_agg_state, which is used between
queueing the work that starts tx aggregations and actually starting that
work (changing to state IWL_AGG_STARTING).
This solves a race where ieee80211_start_tx_ba_session is called a
second time, before the work queued by the first run has a chance to
change the agg_state. In this case the second call to
ieee80211_start_tx_ba_session returns an error, and the fallback is to
abort the ba session start.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AP interfaces now send all non-bufferable frames using the broadcast
station. Thus allow them to use the probe queue and don't warn about
it.
Fixes: eb045e6e03 ("iwlwifi: mvm: Avoid deferring non bufferable frames")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting wowlan mac80211 requests flush w/o vif
and we ignore this request. As a result some packets
stay stuck in the queue and it may end up with a queue
hang.
Allow the driver to flush queues even if station isn't
specified.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we set disconnect on wowlan and run suspend/resume, will run
into:
...snipped
iwlwifi 0000:01:00.0: Failed to load firmware chunk!
iwlwifi 0000:01:00.0: Could not load the [0] uCode section
iwlwifi 0000:01:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
It is because we still keep IWL_MVM_STATUS_IN_HW_RESTART in
__iwl_mvm_resume. When mac80211 starts the device as
__iwl_mvm_mac_start(), we will miss iwl_mvm_restart_cleanup(mvm).
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEExu3sM/nZ1eRSfR9Ha3t4Rpy0AB0FAlmw78wACgkQa3t4Rpy0
AB1viw/+K2xrwzsKqrNoNM1sV4bPItUTjay64dPVD5CjJ/pAwou6HCu0gCJCh4kt
mXhLWHds7Q4sBY+DlN9eIagQLJUaw897FWV+tHHirDGKMsE4tBaIct7PLBpM7r5O
H03T5qT9+nDGRAJq6ucLG8v91cTAlBNfEIV73Au9Oi5B0Rq4cs+Tz8xS24EHjfTB
zRcLMaE8qoQjIfrwQsYNQBdvYHY5G+Ui5sbPh3HPLDPzAfKAsc75nbikI2QE//s0
cMv5ro39vy0DGyQmdTqNzzzuWWzYvhUD7EiIr7Dfm9ilhljCiVqZg6y7ZVMB/QNq
+HRD7ShbTnNMx1fx8w5WO6gKGVSeo0Ga6KKEauTGiWJQTfZQLuIBLylSMVclfvBN
4zOv3vC9EUP5qqPt0cby7VV2D+1Z4Lw2GYZZKHF5numMkgHAoDJ+tJHbBFmz1CEX
co/79RFhGLKvZE+8lN40hqvPoYA5NOUO6jyOq384ZbnC190nVqOXvIxi9jmFKBHp
rGBE/8e0VPYlc48m6NUFwAvc0HOeN3/ZVaUnoo6SY8fCbru3yhRYzC3pmcepTEbA
OVBHirgYtntI2mk4FWd2dkTC6aOfP1o11dwm3deaaEtkwaiKlxI2xfnkbsGaMaOh
RW787Y10g0k785ABD/GxynOeqfiXnIxIjMKZiQliR33zxdv4cAI=
=QYS4
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-09-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Back from a long absence, so we have a number of things:
* a remain-on-channel fix from Avi
* hwsim TX power fix from Beni
* null-PTR dereference with iTXQ in some rare configurations (Chunho)
* 40 MHz custom regdomain fixes (Emmanuel)
* look at right place in HT/VHT capability parsing (Igor)
* complete A-MPDU teardown properly (Ilan)
* Mesh ID Element ordering fix (Liad)
* avoid tracing warning in ht_dbg() (Sharon)
* fix print of assoc/reassoc (Simon)
* fix encrypted VLAN with iTXQ (myself)
* fix calling context of TX queue wake (myself)
* fix a deadlock with ath10k aggregation (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The LEDS_CMD command is only supported in some newer FW versions
(e.g. iwlwifi-8000C-31.ucode), so we can't send it to older versions
(such as iwlwifi-8000C-27.ucode).
To fix this, check for a new bit in the FW capabilities TLV that tells
when the command is supported.
Note that the current version of -31.ucode in linux-firmware.git
(31.532993.0) does not have this capability bit set, so the LED won't
work, even though this version should support it. But we will update
this firmware soon, so it won't be a problem anymore.
Fixes: 7089ae634c ("iwlwifi: mvm: use firmware LED command where applicable")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex"),
the code turns on a call to exhalbtc_bind_bt_coex_withadapter(). This
routine contains a bug that causes incorrect antenna selection for those
HP laptops with only one antenna and an incorrectly programmed EFUSE.
These boxes are the ones that need the ant_sel module parameter.
Fixes: 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.13+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when
hw initialisation done"), there is an additional error when the module
parameter ant_sel is used to select the auxilary antenna. The error is
that the antenna selection is not checked when writing the antenna
selection register.
Fixes: bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.12+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In struct ieee80211_tx_info, control.vif pointer and rate_driver_data[0]
falls on the same place, depending on the union usage.
During the whole TX process, the union is referred to as a control struct,
which holds the vif that is later used in the tx flow, especially in order
to derive the used tx power.
Referring direcly to rate_driver_data[0] and assigning a value to it,
overwrites the vif pointer, hence making all later references irrelevant.
Moreover, rate_driver_data[0] isn't used later in the flow in order to
retrieve the channel that it is pointing to.
Cc: stable@vger.kernel.org
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ath.git patches for 4.14. Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
ACPI will rely on device driver to tell it if the device could support
wakeup function when system in D3 state.
This has caused some platform can't support remote wakeup correctly,
because the ACPI wakeup GPE is not enabled, hence registers the .set_wakeup
callback to handle it if device supports wakeup.
Tested with QCA6174 hw3.0, firmware ('WLAN.RM.4.4.1-00008-QCARMSWP-1')
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The actual PCI suspend/resume in ath10k has been handled in wow.c,
but in the case of the device doesn't support remote wakeup,
the .hif_suspend() and .hif_resume() will never be handled.
ath10k_wow_op_suspend()
{
if (WARN_ON(!test_bit(ATH10K_FW_FEATURE_WOWLAN_SUPPORT,
ar->running_fw->fw_file.fw_features))) {
ret = 1;
goto exit;
}
....
ret = ath10k_hif_suspend(ar);
}
So register the PCI PM core to support the suspend/resume if the device
doesn't support remote wakeup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Refactor code in order to avoid identical code for different branches.
Addresses-Coverity-ID: 1248728
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For debugging some problems, it is useful to know the chip revision
add a brcmf_info message logging this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use 64-bit dma for hosts with CONFIG_ARCH_DMA_ADDR_T_64BIT enabled.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check if skb tracking arrays has been already allocated. This additional
check handles the case when init partially failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NULL is not a special type of success here but a error pointer.
So it makes sense to check against NULL in qtnf_map_bar
and return error code.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linux built-in circ_buf implementation assumes that that the
circular buffer length is a power of 2. Make sure that
rx and tx descriptor queue lengths are power-of-2.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag -D__CHECK_ENDIAN was wrong: it should be -D__CHECK_ENDIAN__ instead.
However now this flag is enabled by default, so it can be removed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User space can remove the P2P management interface while it is active
(for example, while listen/search is active) and this can cause
a crash. Ensure the P2P device is fully stopped before removing.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Connect can take longer than current timeout in some scenarios,
for example with long-range antenna array. Increase the timeout
to support these scenarios.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW starts running it can get D0 to D3 interrupt that is a leftover
from previous system suspend while FW was not running.
As this interrupt is not relevant anymore, clear it part of device reset
procedure.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Re-arrange the code to have dedicated function for device configuration
which takes place before FW starts running.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since debugfs is a kernel configuration option, enable the driver to
compile without debugfs.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes there is a firmware crash but the hardware
is not fully stopped and continue to send TX/RX interrupts.
This can cause an overload of messages which can bring the
host down. Add ratelimit to these error messages to fix this.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit 9f5bcfe933 ("ath10k: silence firmware file probing
warnings") the firmware loading was changed from request_firmware() to
request_firmware_direct() to silence some warnings in case it fails.
request_firmware_direct() directly searches in the file system only and
does not send a hotplug event to user space in case it could not find
the firmware directly.
In LEDE we use a user space script to extract the calibration data from
the flash memory which gets triggered by the hotplug event. This way the
firmware gets extracted from some vendor specific partition when the
driver requests this firmware. This mechanism does not work any more
after this change.
Fixes: 9f5bcfe933 ("ath10k: silence firmware file probing warnings")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
irq_wq in struct ath10k_sdio is a remnant from an earlier
version of the sdio patchset.
Its use was removed as a result of Kalle's review, but somehow
the struct member survived.
It is not used and can therefore safely be removed.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In napi_poll, the budget number is used to control the amount of packets
we should handle per poll to balance the resource in the system.
In the list of the amsdu packets reception, we check if there is budget
count left and handle the complete list of the packets, that it will have
chances the very last list will over the budget leftover.
So adding one more parameter - budget_left, this would help while
traversing the list to avoid handling more than the budget given.
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Fix-suggested-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Link: https://lkml.kernel.org/r/26670dce-4dd2-f8e4-0e14-90d74257e739@virtuozzo.com
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
calling memcpy immediately after memset with the same region of memory
makes memset redundant.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 41977e86c9 ("rt2x00: add support for MT7620") we do not
initialize TX_PIN_CFG setting. This cause breakage at least on some
RT3573 devices. To fix the problem patch restores previous behaviour
for non MT7620 chips.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1480829
Reported-and-tested-by: Jussi Eloranta <jussi.eloranta@csun.edu>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a missing unlock if rsi_find_sta() fails in
rsi_mac80211_ampdu_action() or if we hit the -EINVAL path in
rsi_mac80211_sta_add().
Fixes: 3528608f3a ("rsi: handle station connection in AP mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These devices support -34.ucode, so load it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use bcast station for all non bufferable frames on AP and AD-HOC.
The host is no longer aware of STAs PS status because of buffer
station offload, so we can't rely on mac80211 to toggle on
IEEE80211_TX_CTL_NO_PS_BUFFER bit.
A possible issue with buffering such frames, beside the obvious spec
violation, is when a station disconnects while in PS but the AP isn't
aware of that. In such scenarios the AP won't be able to send probe
responses or auth frames so the STA won't be able to reconnect and
the AP will have a queue hang.
Fixes: 3e56eadfb6 ("iwlwifi: mvm: implement AP/GO uAPSD support")
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a debug print that sometimes reaches over
110 chars, thus generating a warning in those cases.
Split the print into two to prevent these cases.
Fixes: 92b0f7b26b ("iwlwifi: split the regulatory rules when the bandwidth flags require it")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Work queues cannot be allocated when a mutex is held because the mutex
may be in use and that would make it sleep. Doing so generates the
following splat with 4.13+:
[ 19.513298] ======================================================
[ 19.513429] WARNING: possible circular locking dependency detected
[ 19.513557] 4.13.0-rc5+ #6 Not tainted
[ 19.513638] ------------------------------------------------------
[ 19.513767] cpuhp/0/12 is trying to acquire lock:
[ 19.513867] (&tz->lock){+.+.+.}, at: [<ffffffff924afebb>] thermal_zone_get_temp+0x5b/0xb0
[ 19.514047]
[ 19.514047] but task is already holding lock:
[ 19.514166] (cpuhp_state){+.+.+.}, at: [<ffffffff91cc4baa>] cpuhp_thread_fun+0x3a/0x210
[ 19.514338]
[ 19.514338] which lock already depends on the new lock.
This lock dependency already existed with previous kernel versions,
but it was not detected until commit 49dfe2a677 ("cpuhotplug: Link
lock stacks for hotplug callbacks") was introduced.
Reported-by: David Weinehall <david.weinehall@intel.com>
Reported-by: Jiri Kosina <jikos@kernel.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stephen Rothwell reported quite a few conflicts in iwlwifi between
wireless-drivers and wireless-drivers-next. To avoid any problems later in
other trees merge w-d to w-d-next to fix those conflicts early.
Make these const as they are only stored in the const field of a
net_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ieee80211_ops are not supposed to change at runtime. All functions
working with ieee80211_ops provided by <net/mac80211.h> work with
const ieee80211_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in RT_TRACE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check memory allocation failure and return -ENOMEM in such a case, as
already done a few lines below.
As 'dev->tx_q' can be NULL, we also need to check for that in
'mt7601u_free_tx()', and return early.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a static checker fix. "cal_num" is 10. We're declaring the
tx_dt[] and rx_td[] arrays as 3 element arrays. The static checker
complains that we do:
tx_dt[cal] = (vdf_y[1]>>20)-(vdf_y[0]>>20);
"cal" is the iterator and it is in the 0-9 range so it looks like
we could corrupt memory.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactor code in order to avoid identical code for different branches.
This issue was detected with the help of Coccinelle.
Addresses-Coverity-ID: 1415177
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following commits:
commit c815fdebef ("wlcore: spi: Populate config firmware data")
commit d776fc86b8 ("wlcore: sdio: Populate config firmware data")
Populated the nvs entry for wilink6 and wilink7 only while it is
still needed for wilink8 as well.
This broke user space backward compatibility when upgrading from older
kernels, as the alternate mac address would not be read from the nvs that
is present in the file system (lib/firmware/ti-connectivity/wl1271-nvs.bin)
causing mac address change of the wlan interface.
This patch fix this and update the structure field with the same default
nvs file name that has been used before.
In addition, some distros hold a default wl1271-nvs.bin in the file
system with a bogus mac address (deadbeef...) that overrides the mac
address that is stored inside the device.
Warn users about this bogus mac address and use the internal mac address
Fixes: c815fdebef ("wlcore: spi: Populate config firmware data")
Fixes: d776fc86b8 ("wlcore: sdio: Populate config firmware data")
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.14. Major changes:
ath10k
* initial UBS bus support (no full support yet)
* add tdls support for 10.4 firmware
ath9k
* add Dell Wireless 1802
wil6210
* support FW RSSI reporting
Unlike the other sections of the NVM, the hw section is in big-endian.
To read a value from it, we had to cast it to __be16. Fix that by
using __be16 * for the entire section.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
At this point we have already copied the cfg pointer to mvm and we
have been dereferencing this pointer many times before, so it will
never be NULL or we would have crashed. Remove the useless check.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always call iwl_nvm_init() with read_nvm_from_nic == true, so this
argument is useless. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We read the regulatory.lar_enabled field in iwl_fw_get_nvm() and store
it in nvm->lar_enabled, taking care of endianness. But then later we
read it again to pass the value to iwl_init_sbands() without handling
endianness. To solve this, simply reuse nvm->lar_enabled when calling
that function.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The OTP in some SKUs have erroneously allowed 40MHz and 80MHz channels
in the 5.2GHz band. The firmware has been modified to not allow this
in those SKUs, so the driver needs to do the same otherwise the
firmware will assert when we try to use it.
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tx BA session should be started according to the current throughput
without any dependence on the internal rate scaling state. The criteria
for opening a BA session will be 10 frames per second.
Sending frequent del BAs can cause inter-op issues with some APs. We'll
not close a BA session until we receive an explicit del BA from the
peer.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some new flags in the channel flags that we don't know
about. Also, the "WIDE" flag is very confusing, because it actually
means 20MHz bandwidth, which is not very wide.
Add the new flags and rename the confusing one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer versions of A000 devices come with two diffenent RF modules.
The PCI_ID, the subsystem ID and the RF ID are identical in these two cases,
so we need to differentiate them by using the CSR_HW_RF_ID register-
in order to load the appropriate firmware.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code did not consider the case that the channel switch counter
is <= 1, which would result with an inaccurate calculation of the
time event apply time.
As the specification states that in case of counter == 0 the switch
occurs at any time after the reception the frame, and for counter == 1
the switch would happens before the next TBTT, schedule the time
event immediately.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These messages are not reporting a real error, just the fact that the
firmware knows about more flags than the driver.
Currently these messages are presented to the user during boot if there
is no bootsplash covering the console, even when booting the kernel with
"quiet".
Demoting it to the warn level helps having a clean boot process.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the BT_MBOX_PRINT() macro from mvm/debugfs.c to fw/api/coex.h so
it can be reused and remove duplicate definition of BT_MBOX_MSG(),
keeping only the one already in coex.h.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we flush a queue, the packets will have a 'failed'
status but we shouldn't send a BAR. This check was missing.
Because of that, when we got an ampdu_action with
IEEE80211_AMPDU_TX_STOP_FLUSH, we started the following
ping pong with the firmware:
1) Set the station as 'draining'
2) Get a failed Tx status (DRAINED)
3) Send a BAR because of the failed Tx status
(loop of 2 and 3)
This loop wasn't endless since the BAR isn't sent on a
queue that would trigger a "nested" BAR.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a time event is already scheduled when trying to schedule one for
channel switch, the code assumes the channel switch is already
scheduled and no further action is required.
However, it is possible that the scheduled time event is actually
for session protection (e.g. when the first beacon after association
contains the CSA IE). In this case the channel switch will not be
scheduled which will finally lead to disconnection.
Fix this by removing the old time event and schduling a new one for
the channel switch.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware team is now re-using a bit that hasn't been
used for a few generations. Re-use for TX_ON_AIR drop.
This bit will be set by the firmware to indicate that
a frame in an A-MPDU was dropped but not because of the
already mapped reasons.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We use mvmsta for the sta->drv_priv in mvm, but in rs.c we have a
bunch of instances using sta_priv, which is probably due to it being
copied from dvm. Change all occurrences to mvmsta for consistency
with the rest of the driver
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have some of the SAR dummy functions when ACPI is not set declared
in mvm.h and some declared in fw.c. Group them all together in fw.c
for consistency and to avoid static/non-static issues.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a valid baid in a received frame, we need to
check that we are aware of this baid. If not, we check
that the OLD_SN bit set. If that's not the case, we issue
a WARNING. Print more data when that happens.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This name was missing in the list.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows to modify TFD_TX_CMD_SLOTS to a power of 2
which is smaller than 256.
Note that we still need to set values to wrap at 256
into the scheduler's write pointer, but all the rest of
the code can use shorter transmit queues.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware now adds more information about time sharing
with the Bluetooth core.
Adapt the API structures and add the new fields in the
debugfs hooks.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_wait_notification() function removes the wait entry from the
list. To make it clearer that it's doing the same thing as
iwl_remove_notification(), call the latter instead of having duplicate
code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to differentiate an INIT that ended early because of
RFKILL from one that succeded. Additionally, if INIT fails later,
during calibration, due to RFKILL, we can just return success and
continue as if we were already in RFKILL to start with.
Remove this unnecessary differentiation and do some other small
clean-ups while at it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The corunning block was supposed to help in coex scenarios.
It required the driver to configure the firmware based on
the coupling between the two antennas of the devices.
This was never in use and the configuration sent by the
driver has always been blank.
Remove all that code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Station id should be set in load key frame configured to device.
For WEP mode, key is configured once from mac80211. This key is
saved and configured to device every time a station is connected.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame ampdu aggregation parameters is updated to
include sta_id for AP mode.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Auto rate frame is sent to firmware when a new station is
connected. Station id and station's ht capabilities are updated
in auto rate command frame.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame auto rate request is modified to use common
descriptor struture.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Station id needs to be get for data and management frames
to fill in the descruptor for AP mode. Few other changes
related to AP mode are covered here.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When sta_remove of mac80211 is called, driver iterates through
list of existing stations to get the station id. Then peer notify
is prepared and send to firmare.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Station structures are maintained in driver with required
fields. When mac80211 callback sta_add is called, driver
iterates through list of connected stations to check available
index and assigns station id which is important for further
communication to that station. Then peer notify frame is send
to firmware to inform the firmware about new station connection.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mac80211 config parameter BEACON_ENABLE is handled. When VAP
capabilities frame with AP mode is configured to firmware, beacon
events start coming to host at each PreTBTT. At this time, beacon
is taken from mac80211, descriptor is prepared and send to firmware.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove_interface callback of mac80211 is handled for AP mode.
Same is notified to firmware through vap_capabilities frame
with VAP status VAP_DELETE.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP mode is handled in add_interface callback of mac80211.
Also for AP mode, sending rx filter frame to disallow beacons
to host is added. Station structures are initialized to NULL.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP mode support is advertised to cfg80211. Necessary wiphy
parameters are initialized.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Perform additional reclaim from qtnf_pcie_data_tx. Lock tx_lock serves only
reclaim synchronization purposes. Rename it accordingly and improve
granularity moving this lock to qtnf_pcie_data_tx_reclaim.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce counter for Rx underflow events. Export this counter via debugfs.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current code for both Rx and Tx queue management is a custom and incomplete
circular buffer implementation. It makes a lot of sense to switch to kernel
built-in circ_buf implementation.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoid extra buffering in driver by default. Use max hardware Tx queue size.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update PCIE_HDP_TX_HOST_Q_WR_PTR register in skb2rbd_attach as a part of
procedure of passing new Rx buffer to hardware. Sync up all the the
qtnf_rx_bd descriptor updates before passing Rx buffer to hardware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace __dev_alloc_skb and explicit NET_IP_ALIGN alignment by built-in
__netdev_alloc_skb_ip_align function.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use napi_gro_receive() rather than netif_receive_skb() to improve
performance when GRO is enabled.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At the end of user scan request, driver will perform an active
scan for hidden SSIDs in passive channels. While doing this,
driver unconditionally adding random_mac in scan command, which
is no expected. It should add random_mac only if scan_request
has NL80211_SCAN_FLAG_RANDOM_ADDR flag set.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver should use random MAC address only if the scan is
requested by user(provided NL80211_SCAN_FLAG_RANDOM_ADDR
is set in scan request). It should not be used for a scan
performed before association.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware feature check introduced for multi-scheduled scan turned out
to be failing for bcm4343{0,1,8} devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Ian Molton <ian@mnementh.co.uk>
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Some more code moved to a new directory;
* Fixes in LED handling;
* Some FW API updates;
* General fixes and cleanups here and there.
-----BEGIN PGP SIGNATURE-----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=PgZZ
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-08-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Sencond batch of iwlwifi patches for 4.14
* Some more code moved to a new directory;
* Fixes in LED handling;
* Some FW API updates;
* General fixes and cleanups here and there.
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Tested-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch check whether userspace beacon data include country
ie, if so then download command to enable 11d setup in firmeare
accordingly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware API defined in the header files didn't match
the structure that are actually passed by the firmware.
The impact could be a decision for MIMO in Tx or Rx in
coex scenarios.
Fixes: 430a3bbafd ("iwlwifi: mvm: BT Coex - new API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we unmap a non-empty Tx queue, we need to free the
pages that we allocated for the headers in TSO flows.
This code existed for the 9000 device family, but somehow
it got left out when the new Tx path for the A000 devices
was written.
Fixes: 2b0c5946d9ed ("iwlwifi: pcie: introduce a000 TX queues management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi. These references were inherited from a previous
project and are irrelevant here. Additionally, remove some irrelevant
references to 5100 HW. Remove all these.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Although nmi was triggered fine till now, it appears
that the driver didn't write the exact correct values
to the correct addresses for each HW.
Fix the nmi triggering by setting the correct addresses
and values.
Fixes: 4c9706dc2f ("iwlwifi: update nmi register")
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TVQM tells us the initial write pointer for a queue,
but that write pointer is in WiFi sequence number unit
and not in TFD index unit. Which means that the write
pointer in the TVQM's response can be bigger than the
Tx queue ring size.
Fix that by modulo'ing the write pointer from the TVQM
with the Tx queue size.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the queue config params is the associated station id.
Hence the FW must know about the station prior to the queue allocation.
In a000 devices, allocating a queue without a valid station
results with assert 0x2B00.
In FW restart flow the queues are allocated before
adding the station so first add the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix this issue if it is not supported by the firmware.
Fixes: 00f481bd89 ("iwlwifi: mvm: add ctdp operations to debugfs")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support a new version of the beacon template command. This replaces v8
of the command, which was missing the rate code. Also, export rate
decision logic to a separate function.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When an RX block-ack session times out, the firmware, which offloads
RX reordering but not the BA session negotiation, stops the session
but doesn't send a DELBA. This causes the the session to remain
active in the remote device, so no more BA sessions will be
established, causing a severe throughput degradation due to the lack
of aggregation.
Use the new ieee80211_rx_ba_timer_expired API when the ba session timer
expires, since this will tear down the ba session and also send a delba.
The previous API used is intended for drivers that offload the
addba/delba negotiation, but not the rx reordering, while our driver
does the opposite.
This patch depends on "mac80211: add api to start ba session timer
expired flow".
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there is no value received from BIOS
for cTDP budget, the default should be 2000 mWatt.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the NVM data in a000 devices should be shared
across operation mode.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the smem configuration to the fw data dump, once
the firmware crashes. This is useful mainly for later
parsing of the smem.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the defines has a wrong value.
Fixes: 1afb0ae421 ("iwlwifi: allow combining different phy images with mac images")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Load FW according to NIC type,
taking into account simulation, if exists.
This is determined by a prph register.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are a few places where we don't have a space between the * and
the @ in the parameter description. Also, in one case, the @ had
trailing space before the parameter name.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change iwl_set_ucode_api_flags(), iwl_set_ucode_capabilities() to be void.
No need to check returned values.
Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CT-kill is a thermal-based "RF-kill", which disables the NIC
completely if the temperature gets too high, in order to avoid damage.
Add a debugfs entry to simulate high temperatures, in order to test
CT-kill flows in the driver without having to physically heat the
device up.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.
Fixes: 503ab8c56c ("iwlwifi: Add 8000 HW family support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the module parameter is set to disable the LED, we leave the
initialization routine before setting the LEDS_INIT_COMPLETE
status bit. Therefore, there's no need to check the parameter
again on exit, just the status check is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we start an Rx A-MPDU session, we first get the AddBA
request, then we send an ADD_STA command to the firmware
that will reply with a BAID which is a hardware resource
that tracks the BA session.
This BAID will appear on each and every frame that we get
from the firwmare until the A-MPDU session is torn down.
In the Rx path, we look at this BAID to manage the
reordering buffer.
This flow is inherently racy since the hardware will start
to put the BAID in the frames it receives even if the
firmware hasn't sent the response to the ADD_STA command.
This basically means that the driver can get frames with
a valid BAID that it doesn't know yet.
When that happens, the driver used to WARN.
Fix this by simply not WARN in this case. When the driver
will know abou the BAID, it will initialise the relevant
states and the next frame with a valid BAID will refresh
them.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AP mode, if a station is removed just as it is adding a new stream,
the queue in question will remain stopped and no more TX will happen
in this queue, leading to connection failures and other problems.
This is because under DQA, when tx is deferred because a queue needs
to be allocated, the mac queue for that TID is stopped until the new
stream is added. If at this point the station that this stream
belongs to is removed, all the deferred tx frames are purged, but the
mac queue is not restarted. As a result, all following tx on this
queue will not be transmitted.
Fix this by starting the relevant mac queues when the deferred tx
frames are purged.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
vring_idle_trsh is used in the operational driver, hence
should not be defined as a debugfs variable.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store initial FW RF calibration result in driver. Set this calibration
result back to FW after each FW reset in order to avoid future calibration
procedures.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While wil_open is executed, any call to netif_running
would return a success. In case there are failures
within wil_open, should not treat the device as if it
is already opened in relevant functions (like FW recovery
and runtime suspend check).
Fix that by checking the device up flag instead.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set wowlan to indicate that 11ad device can wake-up
on any trigger and disconnect.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add statistics for total, min and max suspend time, that
calculates the time the 11ad device was in suspend.
Those statistics will help to estimate the power impact
of d3hot feature.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reset 11ad device on resume failure only if no_fw_recovery
is not set.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New FW supports reporting RSSI signal in dBm.
Report RSSI to kernel in case FW has this capability.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Validate buffer length has the minimum needed size
when sending management frame to protect against
possible buffer overrun.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set RX_FLAG_DECRYPTED in case of MMIC failure so that
ieee80211_rx_h_decrypt() doesnt drop the frame before getting to
ieee80211_rx_h_michael_mic_verify().
Signed-off-by: Michael Skeffington <mike@astro.ai>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rate_control_ops structure is only passed as an argument to the
function ieee80211_rate_control_{register/unregister}. This argument
is of type const, so declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add const to bin_attribute structure as it is only passed to the
functions sysfs_{remove/create}_bin_file. The corresponding arguments
are of type const, so declare the structure to be const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After association, ping is not working when sweeping the channel at the
AP side. It is caused by having incorrect carrier state (OFF) for the STA
in successful roaming. This patch sets the carrier state ON for the case.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the device/firmware supports multi-channel, it can have P2P
connection and regular connection with AP simultaneous. In this case,
the num_different_channels in wiphy info was not correct when firmware
supports multi-channel (The iw wiphy# info showed "#channels <= 1" in
interface combinations). It caused association failed and error message
"CTRL-EVENT-FREQ-CONFLICT error" in wpa_supplicant when P2P GO interface
was running at the same time.
The root cause is that the num_different_channels was always overridden
to 1 in brcmf_setup_ifmodes even multi-channel was enabled.
We correct the logic by moving num_different_channels setting forward.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When setting wpa_auth to WPA_AUTH_NONE(1) in AP mode with WEP security,
firmware will set privacy bit and add WPA OUI in VENDOR IE in beacon and
probe response. The security type in softAP beacons confuse the
supplicant in client side, and the user client will see [WPA-?] in
supplicant scan result. So we set WPA_AUTH_DISABLED in softAP mode with
OPEN security.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per below statement about p2p device address in WFA P2P
spec $2.4.3:
The P2P Device Address of a P2P Device shall be its globally
administered MAC address, or its globally administered MAC
address with the locally administered bit set.
This patch follow above statement, using a separate device
address for p2p interface
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch wrapper wps ie in pass through tlv, so that
firmware could parse correctly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 4d7ab36f0c ("mwifiex: Do not change bss_type in
change_virtual_intf") kept original bss_type unchanged. bss_num should
keep the same style, in this way. Unique tuple (bss_type, bss_num) will
be able to locate the right priv structure.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver is doing netif_carrier_off during suspend, which will set
the IFF_LOWER_UP flag to 0. As a result certain applications
will think this as a real carrier down and behave accordingly.
This will cause issues like loss of IP address, for example. To
fix this use netif_device_dettach during suspend.
Fixes: 0026b32d72 ('mwifiex: fix Tx timeout issue during suspend test')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Provision is added for configuring RTS threshold by sending
vap dynamic update frame to firmware.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BUFFER_AVAILABLE interrupt is sent by firmware to indicate
change in buffer status. We should check buffer status while
handling this interrupt. Currently buffer status is checked
only while dequeueing packets. This patch fixes a data
traffic stuck problem observed occasionally.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We get buffer full event from firmware whenever Tx queue is full
Host should stop writing packets after this and resume after
buffer free event.
Buffer status checking is optimized for once in 4 times if
BUFF_FULL condition is not set, otherwise once for every
packet.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rsi_sdio_check_buffer_status would be the appropriate name
for this function as we are checking hardware buffers
availability status.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for U-APSD power save. Configuration
frame is downloaded to firmware with default settings and
support is advertised to mac80211
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame set_antenna is modified to use common
descriptor structure. Also it's subframe type is set.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements rfkill_poll handler. Also, necessary changes
are done in interface up and down handler to support rfkill
functionality.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the uninitialized descriptor pointer
issue in function rsi_send_internal_mgmt_frame().
Descriptor should point to start of the skb data.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9a629fafe7 ("rsi: immediate wakeup bit and priority for TX command packets")
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath_ps_ops structures are only stored as a reference in the ps_ops
field of a ath_common structure. This field is of type const, so make
the structures as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As the association status changes the driver needs to configure the
hardware. This is done based on information in the "sta" acquired by
ieee80211_find_sta(), which requires the caller to ensure that the "sta"
is valid while its being used; generally by entering an rcu read
section.
But the operations acting on the "sta" has to communicate with the
firmware and may therefor sleep, resulting in the following report:
[ 31.418190] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:238
[ 31.425919] in_atomic(): 0, irqs_disabled(): 0, pid: 34, name:
kworker/u8:1
[ 31.434609] CPU: 0 PID: 34 Comm: kworker/u8:1 Tainted: G W
4.12.0-rc4-next-20170607+ #993
[ 31.441002] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[ 31.450380] Workqueue: phy0 ieee80211_iface_work
[ 31.457226] Call trace:
[ 31.461830] [<ffffff8008088c58>] dump_backtrace+0x0/0x260
[ 31.464004] [<ffffff8008088f7c>] show_stack+0x14/0x20
[ 31.469557] [<ffffff8008392e70>] dump_stack+0x98/0xb8
[ 31.474592] [<ffffff80080e4330>] ___might_sleep+0xf0/0x118
[ 31.479626] [<ffffff80080e43a8>] __might_sleep+0x50/0x88
[ 31.485010] [<ffffff80088ff9a4>] mutex_lock+0x24/0x60
[ 31.490479] [<ffffff8008595c38>] wcn36xx_smd_set_link_st+0x30/0x130
[ 31.495428] [<ffffff8008591ed8>] wcn36xx_bss_info_changed+0x148/0x448
[ 31.501504] [<ffffff80088ab3c4>]
ieee80211_bss_info_change_notify+0xbc/0x118
[ 31.508102] [<ffffff80088f841c>] ieee80211_assoc_success+0x664/0x7f8
[ 31.515220] [<ffffff80088e13d4>]
ieee80211_rx_mgmt_assoc_resp+0x144/0x2d8
[ 31.521555] [<ffffff80088e1e20>]
ieee80211_sta_rx_queued_mgmt+0x190/0x698
[ 31.528239] [<ffffff80088bc44c>] ieee80211_iface_work+0x234/0x368
[ 31.535011] [<ffffff80080d81ac>] process_one_work+0x1cc/0x340
[ 31.541086] [<ffffff80080d8368>] worker_thread+0x48/0x430
[ 31.546814] [<ffffff80080de448>] kthread+0x108/0x138
[ 31.552195] [<ffffff8008082ec0>] ret_from_fork+0x10/0x50
In order to ensure that the "sta" remains alive (and consistent) for the
duration of bss_info_changed() mutual exclusion has to be ensured with
sta_remove().
This is done by introducing a mutex to cover firmware configuration
changes, which is made to also ensure mutual exclusion between other
operations changing the state or configuration of the firmware. With
this we can drop the rcu read lock.
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The rx ring buffers are added to a hash table if
firmware support full rx reorder. If the full rx
reorder support flag is not set before allocating
the rx ring buffers, none of the buffers are added
to the hash table.
There is a race condition between rx ring refill and
rx buffer replenish from napi poll. The interrupts are
enabled in hif start, before the rx ring is refilled during init.
We replenish buffers from napi poll due to the interrupts which
get enabled after hif start. Hence before the entire rx ring is
refilled during the init, the napi poll replenishes a few buffers
in steps of 100 buffers per attempt. During this rx ring replenish
from napi poll, the rx reorder flag has not been set due to which
the replenished buffers are not added to the hash table
Set the rx full reorder support flag before we allocate
the rx ring buffer to avoid the memory leak.
Signed-off-by: Rakesh Pillai <pillair@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Each time we get disconnected from AP we get flooded with messages like:
...
ath10k_pci 0000:03:00.0: no channel configured; ignoring frame(s)!
<until ratelimit kicks in>
ath10k_warn: 155 callbacks suppressed
...
Use ath10k_dbg() here too.
Signed-off-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should free 'wgds.pointer' here as done a few lines above in another
error handling path.
It was allocated within 'acpi_evaluate_object()'.
Fixes: c52030a01ccc ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the Dell Wireless 1802 card as an AR9462 in the ath9k pci list.
Note that the wowlan feature is supported and has been tested
successfully.
Signed-off by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes a trivial debugfs file permission issue. Debugfs
file ack_to has no write function, so S_IWUSR gets purged.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI interface for all the firmwares(except QCA6174) does not include the
type of peer(default/bss/tdls) requested during peer creation, therefore
target creates a default peer.
TDLS implementation on 10.4 firmware requires host to configure the
peer type(tdls) for TDLS peers. This patch adds peer type parameter to the
existing WMI interface for peer creation to accommodate this requirement.
Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2)
with ping tests for AP/STA modes.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds the support of TDLS feature for 10.4 firmware
versions.
A new WMI service is added to advertise the support of TDLS for
10.4 firmwares.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Though there is room to accommodate 512 services in wmi service
ready event, target uses only first 4-bits of each 32-bit word for
advertising wmi services thereby limiting max wmi services to 64.
TDLS implementation for 10.4 firmwares introduces new wmi services by
making use of remaining unused bits of each 32-bit word, therefore the
wmi service mapping in host needs to be extended.
This patch adds the logic to extend the wmi SVCMAP to accommodate new
wmi services.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As suggested by Arnd Bergmann, replace
"while (time_before_...) {}"
with
"do {} while (time_before_...)"
This fixes the following warnings detected by gcc 4.1.2:
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_mbox_rxmsg_pending_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:676: warning: ‘ret’ may be used uninitialized in this function
...
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_irq_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:1331: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA9377 have support for USB so add initial USB bus
support to ath10k. With this patch we have the low level HIF and
HTC protocol working and it's possible to boot the firmware,
but it's still not possible to connect or anything like.
More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k USB support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the a-mpdu reference number in ath10k to make it accessible in the
receivers radiotap header. Implemented as in ath9k. The reference number is
needed for troubleshooting and research at the receivers site (e.g. to identify
mpdu's that were aggregated in an a-mpdu)
Signed-off-by: Matthias Frei <mf@frei.media>
[kvalo@qca.qualcomm.com: fix checkpatch warning, commit log cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In _rtl_init_mac80211(), hardcoded value for hw->max_listen_interval
and hw->max_rate_tries are replaced by macro and removed the comment.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes, we might using wifi-only firmware with a combo firmware name,
in this case, do not need to filter bluetooth part from header.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
uninitilized variable, such as .add_req_result might be magic stack
value. Initialize the structure to make it clean.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After commit cf124db566 ("net: Fix inconsistent teardown and
release of private netdev state."), setting
'dev->needs_free_netdev' ensures device data is released, and
'dev->destructor' is not used anymore.
Fixes: cf124db566 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1899 928 0 2827 b0b realtek/rtlwifi/rtl8192ee/sw.o
File size After adding 'const':
text data bss dec hex filename
1963 864 0 2827 b0b realtek/rtlwifi/rtl8192ee/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3090 912 0 4002 fa2 realtek/rtlwifi/rtl8188ee/sw.o
File size After adding 'const':
text data bss dec hex filename
3154 848 0 4002 fa2 realtek/rtlwifi/rtl8188ee/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3032 912 0 3944 f68 realtek/rtlwifi/rtl8723be/sw.o
File size After adding 'const':
text data bss dec hex filename
3096 848 0 3944 f68 realtek/rtlwifi/rtl8723be/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2775 912 0 3687 e67 realtek/rtlwifi/rtl8723ae/sw.o
File size After adding 'const':
text data bss dec hex filename
2839 848 0 3687 e67 realtek/rtlwifi/rtl8723ae/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2491 960 0 3451 d7b realtek/rtlwifi/rtl8821ae/sw.o
File size After adding 'const':
text data bss dec hex filename
2587 864 0 3451 d7b realtek/rtlwifi/rtl8821ae/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2817 1040 0 3857 f11 realtek/rtlwifi/rtl8192se/sw.o
File size After adding 'const':
text data bss dec hex filename
3009 848 0 3857 f11 realtek/rtlwifi/rtl8192se/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2833 945 12 3790 ece realtek/rtlwifi/rtl8192de/sw.o
File size After adding 'const':
text data bss dec hex filename
2929 849 12 3790 ece realtek/rtlwifi/rtl8192de/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the only caller of dma_supported() outside of DMA API internals, the
qtfnmac driver stands out and invites scrutiny. Thankfully, it's not
being used for evil, but it is entirely redundant, since it open-codes a
check that the DMA mask setting functions are going to perform anyway.
In fact, the whole qtnf_pcie_init_dma_mask() function is nothing more
than a rather long-winded implementation of dma_set_mask_and_coherent(),
so let's just use that directly.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify qlink command structures and interface types handling
to prepare adding AP_VLAN support to qtnfmac driver.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is not used anymore, so remove it.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends supported interface type rather than mask. As a result,
types field of ieee80211_iface_limit structure may end up having
multiple iftype bits set. This leads to WARN_ON from
wiphy_verify_combinations.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Userspace tools may hang on scan in the case when scan completion event
is not returned by firmware. This patch implements the scan timeout
to avoid such situation.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements cfg80211 channel_switch handler enabling CSA
channel-switch procedure.
Driver performs only basic validation of the requested new channel
and then sends command to firmware. Beacon IEs are not sent since
beacon update is handled by firmware.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless cfg80211 core supplies channel settings in cfg80211_ap_settings
structure for each BSS in multiple BSS configuration. On the other hand
all the virtual interfaces on one radio are using the same PHY settings
including channel.
Move chandef structure from vif to mac structure in order to mantain
the only instance of cfg80211_chan_def structure in qtnf_wmac
rather than its multiple copies in qtnf_vif.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use proper endianness conversion for client station leave reason.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement current channel reporting functionality. Current operating
channel can be obtained either directly using cfg80211 get_channel
callback or from stats reported by cfg80211 survey_dump callback.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add missing bus lock into get_mac_chan_info command.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Regdomain information needs to be registered with cfg80211
for devices with REGULATORY_WIPHY_SELF_MANAGED flag set.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On startup driver obtains regulatory rules from firmware and
enables them during wiphy registration. Later on regulatory
domain change can be requested by host. In this case firmware
is notified about the upcoming changes. If the change is valid,
then firmware updates hardware channel configuration and host
driver receives updated channel info for each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit f70e4df2b3 ("rtlwifi: Add code to read new versions of
firmware") added code to load an old firmware file if the new one is
not available. Unfortunately that code is never reached because
request_firmware_nowait() does not wait for the firmware to show up
and returns 0 even if the file is not there.
Use the existing fallback mechanism introduced by commit 62009b7f12
("rtlwifi: rtl8192cu: Add new firmware") instead.
Fixes: f70e4df2b3 ("rtlwifi: Add code to read new versions of firmware")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that some IEs get missed during association.
This patch correct the old IE parse code. sme->ie will be
store as wpa ie, wps ie, wapi ie and gen ie accordingly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
_rtl_pci_find_adapter fail path will jump to label fail3 for
unsupported adapter types.
However, on course for fail3 there will be call rtl_deinit_core
before rtl_init_core.
For the inclusion of checking pci_iounmap this fail can be moved to
fail2.
Fixes
[ 4.492963] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 4.493067] IP: rtl_deinit_core+0x31/0x90 [rtlwifi]
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_add_bcast_sta() and the iwl_mvm_rm_bcast_sta() functions
are only called in P2P flows. Add _p2p_ to the function names to make
this explicit.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to spell out the cases when we can just
use ieee80211_is_bufferable_mmpdu().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the TXQ timer freeze code will not properly handle the
large TVQM queue numbers, warn if we get into that code when
we have TVQM. Also, just to catch this earlier, warn if the
firmware image doesn't support AP_LINK_PS but we're running
on HW using TVQM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename this function to the more appropriate iwl_pcie_check_hw_rf_kill()
since it's only a function in the pcie code and cannot be called from
any other place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing purposes, we may want to disable EBS scans at compile time.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During init, the FW checks whether the FSEQ value matches what it
expects. If it doesn't match, we print a warning to let integrators
clearly know that something is wrong. This can happen if another core
(i.e. not WiFi) has updated the FSEQ version. This notification is
only sent by the FW in production, for development firmwares, an
assertion is triggered instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
If the OTP is empty, the NVM_GET_INFO command returns
with flags' bit(0) on. This means the FW returns the
default values for working with. This is allowed, so
use this returned data.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return status check of iwl_pcie_gen2_build_amsdu
was buggy. Fix it.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While waiting for queues to empty,
If txq_id == IWL_MVM_INVALID_QUEUE for all txq_ids,
ret is used uninitialized.
Found by Klocwork.
Fixes: d6d517b773 ("iwlwifi: add wait for tx queue empty")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FIFO numbering is different in A000 devices. This
means that we routed BE packets to BK FIFO. Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently support 3 different versions of the beacon template
command and the code does some tricks in order to reuse what is
possible across these versions. But it is a bit complicated to read
and soon there will be one more variation that the driver needs
implement, which would complicate it even further.
Refactor the way we send beacon template commands, which increases the
code size a bit, but makes it much easier to read.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Those constants have been unused for quite some time now.
Signed-off-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Convention has it to byte-swap the constant instead of the variable
when doing bit checks. This also generates better code when the swap
is actually needed, since the constant can be swapped at compile-time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two workarounds because RSS is currently broken on A000
devices due to firmware issues, but checking for the new TX API
doesn't really make sense. Check the hardware family instead of
the new TX API - there's nothing better to check since it's just
a temporary workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This may need to be refined later, but for now using this,
even with the TODO, is better than checking "has new TX API".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the shared memory command parsing into common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two PCI IDs for the 9160 series.
Add five PCI IDs for the 9260 series.
Add one PCI IDs for the 9270 series.
Add seven PCI IDs for the 9460 series.
Add five PCI IDs for the 9560 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.
In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.
Fixes: 5bc5aaad40 ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
C step NICs should use the latest FW (currently B step).
Correct the condition to make C step NICs advanced its default FW name
to the latest one.
Also rename _next_ to b_or_c to avoid confusion.
Fixes: 5da083d192 ("iwlwifi: add support for 9000 HW B-step NICs")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).
This is needed to remove throughput degradation.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.
This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we create a regulatory domain out of an MCC
notification, we need to make sure that all the channels
in the rule have the exact same properties.
The current code mixes channel 36 and 40 although 36 can be
a control channel with HT40+ (36, 40) whereas 40 can't be
a control channel with HT40+ since (40, 44) is invalid.
Because of that, cfg80211 would allow to connect in 40MHz
to APs that are configured to channel 40 HT40+ and that made
our firmware assert.
Fix this by checking the bandwidth flags before taking the
decision if the rule should be split.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299 partly.
Fixes: af45a9003f ("iwlwifi: create regdomain from mcc_update_cmd response")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware now adds a new DWORD for the MLME offload's
capability even on firmware versions that don't support
it.
Add the TLV bit to avoid getting the print:
capa flags index 3 larger than supported by driver.
This fixes the bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=196195
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.
On A000 devices series, the IV is always added by the
device.
Fix this.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The cast here is wrong. We want to cast the pointer but we accidentally
do a no-op cast of the value. We normally want to set us_nav_upper to
WIFI_NAV_UPPER_US (30000) but because of this bug we instead set it to
184 on little endian systems and 0 on big endian ones.
Fixes: 3c05bedb5f ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will fix memory leak when firmware request fails
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
_rtl92cu_init_usb_aggregation() can be removed as it is dummy one
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use rtlpriv instead of rtlhal as argument, so driver and btcoex use
the same definitions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should check addr1 to indicate a packet as broadcast or multicast
in tx desc. An obvious example, a STA transmit an *unicast* ARP packet
where addr1 and DA are the addresses of AP and broadcast respectively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a common enumeration, so we use a common name.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are new PHY table values for the RTL8723BE. The changes require
new parsing code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We use H2C to ask BT's status, and C2H will return the status.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Because it isn't always correct to use EAPOL to check 4-way,
we add a timer to handle exception.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in printk message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in PDEBUG debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Causes the PCI stack to complain, and then eventually call the
PCI remove function, which ipw2100 is not expecting. It then
tries to unregister an already-released netdev and other nasty
things, leading to a panic.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1185518
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in mwifiex_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in aggr_ctrl module parameter
message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tdls uapsd support capability is default disabled during
tdls setup, correspondingly it should also been disabled
in tdls config.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Zhiyuan Yang <yangzy@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to unlock if mwifiex_usb_prepare_tx_aggr_skb() fails.
Fixes: a2ca85ad72 ("mwifiex: usb: add timer to flush aggregation packets")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We inited wakeup info at the beginning of mwifiex_add_card, so we need
to uninit it in the error handling.
It's much the same as what we did in:
36908c4 mwifiex: uninit wakeup info when removing device
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We got a compile warning shows below:
drivers/net/wireless/marvell/mwifiex/sdio.c: In function
'mwifiex_sdio_remove':
drivers/net/wireless/marvell/mwifiex/sdio.c:377:6: warning: variable
'ret' set but not used [-Wunused-but-set-variable]
Per the code, it didn't check if mwifiex_sdio_read_fw_status
finish successfully. We should at least check the return of
mwifiex_sdio_read_fw_status, otherwise the following check of
firmware_stat and adapter->mfg_mode is pointless as the device
is probably dead.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This print isn't very useful. It's also different between
mwifiex_add_card() and mwifiex_reinit_sw(), and I'd like to consolidate
them eventually.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It has some scary comments about "only being called" from the timeout
handler, so let's help keep it that way.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'card->dev' is initialized once and is never cleared. Drop the
unnecessary "safety" check, as it simply obscures things, and we don't
do this check everywhere (and therefore it's not really "safe").
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In testing the mwifiex reset code path, I've noticed KASAN complaining
about some "overwritten poison values" in our RX buffer descriptors.
Because KASAN didn't notice this at the time of a CPU write, this seems
to suggest that the device is writing to this memory.
This makes a little sense, because when resetting, we don't necessarily
expect the device to be responsive, so we don't have a chance to disable
everything cleanly.
We can at least take the precaution of disabling DMA for the device
though, and in my testing that seems to clear up this particular issue.
This patch reorders the removal path so that we disable the device
*before* releasing our last PCIe buffers, and it clears/sets the bus
master feature from the PCI device when resetting.
Along the way, remove the insufficient (and confusing) error path in
mwifiex_pcie_up_dev() (it doesn't unwind things well enough, and it
doesn't propagate its errors upward anyway).
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The card_reset() implementation should be setting our state flags and
cancelling commands for us (i.e., in mwifiex_shutdown_drv()), so let's
not do it here.
Also, this debugfs file is useful for testing and debugging the reset
feature, so we shouldn't do extra preparatory steps here, as that might
cause different reset behavior, which could either cause new bugs or
paper over existing ones that this debug feature should otherwise help
us catch.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After removing the interrupt loop in commit 5d5ddb5e0d ("mwifiex:
pcie: don't loop/retry interrupt status checks"), there is practically
zero difference between mwifiex_process_pcie_int() (which handled legacy
PCI interrupts and MSI interrupts) and mwifiex_process_msix_int() (which
handled MSI-X interrupts). Let's add the one relevant line to
mwifiex_process_pcie_int() and kill the copy-and-paste.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After removing the interrupt loop in commit 5d5ddb5e0d ("mwifiex:
pcie: don't loop/retry interrupt status checks"), we don't need to keep
track of the cleared interrupts (actually, we didn't need to do that
before, but we *really* don't need to now).
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's always called with 'true' -- we only determine it 'false' locally
within this function. So drop the parameter.
Also, this should be 'bool' (since we use true/false), not 'u32'.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Despite the name (and meticulous comments), this function frees no
memory and does not touch any locks. All it does is "delete" the list
heads -- which just means they'll be dangling, and we'll need to re-init
them if we use them again.
It seems like this code would work OK as a sort of canary for using the
list after we've torn everything down, so it's fine to keep the code;
let's just get the name and comments to match what's actually happening.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The .idle_time field *should* be unused, but technically, we're allowing
unitialized stack garbage to pass all the way through to the firmware
host command. Let's zero it out instead.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In reading through _mwifiex_fw_dpc(), I noticed that after we've
registered our wiphy, we still have error paths that don't free it back
up. Let's do that.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we leave the delete interface function, there are still netdev
hooks that might try to process the device. We're short-circuiting some
of that by changing the interface type and clearing ieee80211_ptr. This
means we skip NETDEV_UNREGISTER_FINAL in cfg80211. Fortunately, that is
currently a no-op.
We don't need most of the cleanup here anyway:
* the connection state will get (un)set as part of the disconnect
process (which cfg80211 already initiates for us)
* the interface type doesn't actually need to be cleared at all (it'll
trigger a WARN_ON() in cfg80211 if we do)
* the iee80211_ptr isn't really "ours" to clear anyway
So stop resetting those 3 things.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's possible for some control interfaces (e.g., scans, set freq) to be
active after we've stopped our main work queue and the netif TX queues.
These don't get completely shut out until we've unregistered the wdevs
and wiphy.
So let's only free command buffers and poison our lists after
wiphy_unregister().
This resolves various use-after-free issues seen when resetting the
device.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In general, it's helpful to use the same code for device removal as for
device reset, as this tends to have fewer bugs. Let's move the wiphy
unregistration code into the common reset and removal code.
In particular, it's very hard to properly handle the reset sequence when
something fails. Currently, if mwifiex_reinit_sw() fails, we've failed
to unregister the associated wiphy, and so running something as simple
as "iw phy" can trigger an OOPS, as the wiphy still has hooks back into
freed mwifiex data structures. For example, KASAN complained:
[... see reset fail for other reasons ...]
[ 1184.821158] mwifiex_pcie 0000:01:00.0: info: dnld wifi firmware from 174948 bytes
[ 1186.870914] mwifiex_pcie 0000:01:00.0: info: FW download over, size 608396 bytes
[ 1187.685990] mwifiex_pcie 0000:01:00.0: WLAN FW is active
[ 1187.692673] mwifiex_pcie 0000:01:00.0: cmd_wait_q terminated: -512
[ 1187.699075] mwifiex_pcie 0000:01:00.0: info: _mwifiex_fw_dpc: unregister device
[ 1187.713476] mwifiex: Failed to bring up adapter: -5
[ 1187.718644] mwifiex_pcie 0000:01:00.0: reinit failed: -5
[... run `iw phy` ...]
[ 1212.902419] ==================================================================
[ 1212.909806] BUG: KASAN: use-after-free in mwifiex_cfg80211_get_antenna+0x54/0xfc [mwifiex] at addr ffffffc0ad1a8028
[ 1212.920246] Read of size 1 by task iw/3127
[...]
[ 1212.934946] page dumped because: kasan: bad access detected
[...]
[ 1212.950665] Call trace:
[ 1212.953148] [<ffffffc00020a69c>] dump_backtrace+0x0/0x190
[ 1212.958572] [<ffffffc00020a96c>] show_stack+0x20/0x28
[ 1212.963648] [<ffffffc0005ce18c>] dump_stack+0xa4/0xcc
[ 1212.968723] [<ffffffc0003c4430>] kasan_report+0x378/0x500
[ 1212.974140] [<ffffffc0003c3358>] __asan_load1+0x44/0x4c
[ 1212.979462] [<ffffffbffc2e8360>] mwifiex_cfg80211_get_antenna+0x54/0xfc [mwifiex]
[ 1212.987131] [<ffffffbffc084fc4>] nl80211_send_wiphy+0x75c/0x2de0 [cfg80211]
[ 1212.994246] [<ffffffbffc094f60>] nl80211_dump_wiphy+0x32c/0x438 [cfg80211]
[ 1213.001149] [<ffffffc000ab6404>] genl_lock_dumpit+0x48/0x64
[ 1213.006746] [<ffffffc000ab3474>] netlink_dump+0x178/0x398
[ 1213.012171] [<ffffffc000ab3d18>] __netlink_dump_start+0x1bc/0x260
[...]
This all goes away if we just tear down the wiphy on the way down, and
set it back up if/when we bring the device back up.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rogue cases (due to other bugs) it's possible we try to process an
old command response *after* resetting the device. This could trigger a
double-free (or the SKB can get reallocated elsewhere...causing other
memory corruptions) in mwifiex_pcie_process_cmd_complete().
For safety (and symmetry) let's always NULL out the command buffer as we
free it up. We're already doing this for the command response buffer.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When resetting the device, we might have queued up interrupts that
didn't get a chance to finish processing. We really don't need to handle
them at this point; we just want to make sure they don't cause us to try
to process old commands from before the device was reset.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When PCIe FLR code was added, it explicitly copy-and-pasted much of
mwifiex_remove_card() into mwifiex_shutdown_sw(). This is unnecessary,
as almost all of the code should be reused.
Let's reunite what we can for now.
The only functional changes for now:
* call netif_device_detach() in the remove() code path -- this wasn't
done before, but it really should be a no-op, when the device is
getting totally unregistered soon anyway
* call the ->down_dev() driver callback only after we've finished all
SW teardown -- this should have no significant effect, since the only
user (pcie.c) does very minimal work there, and it doesn't matter
that we reorder this
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
u32 pointer is changed to u16 and filled the value. Problem is
solved by using local temporary variable. Below static checker
warning was reported.
drivers/net/wireless/rsi/rsi_91x_usb.c:400 rsi_usb_master_reg_read()
warn: passing casted pointer 'value' to 'rsi_usb_reg_read()'
32 vs 16.
Fixes: b97e9b94ad ("rsi: Add new host interface operations")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These checks are required. Otherwise we may end up getting
memory corruption if invalid length is passed.
Fixes: b97e9b94ad ("rsi: Add new host interface operations")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4 bytes is fixed size for reading or writing USB register. We
will use a macro instead of hardcoding this.
Fixes: b97e9b94ad ("rsi: Add new host interface operations")
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Below regulatory changes are included this patch
* Country code is saved as it will be used in bgscan.
* Region codes are mapped according to RSI region codes.
* Radar flag settings are moved under the check if 5GHZ band
is enabled.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When interface is down it is better to stop all RX packets to
host. 0xffff will block all packets to host.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device specific descriptor for each TX packet is prepared on top of
skb data address. This descriptor should be pulled out before
indicating the TX status to mac80211.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame block/unblock data is modified to
use common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data queues should be unblocked after station add notify frame
is sent and should be blocked after station delete notify is sent.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When Short Gaurd Interval is enabled bit 9 is set in rate. Otherwise
it should not be set. Added missing 'else' case in this patch.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Broadcast bit to be set for broadcast and multicast packets.
For remove_key, tx and rx mic need not be filled.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame set_key is modified to use common descriptor
structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
VAP capablities frame configured to device is modified to use
common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame set_channel is modified to use common
descriptor structure. Also DFS channel indication to firmware
is added in the descriptor for dfs channels configuration.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Baseband RF programming frame configured to device is modified
to use common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AMPDU aggregation parameters frame configured to device is
modified to use common descriptor structure.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX command frame peer notify is updated to use common descriptor
structure. MPDU density value added to the frame.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function rsi_mgmt_pkt_to_core() is for passing the 802.11
management frames to mac80211. So, it is unnecessary to check
again for the frame type 802.11 management in this function.
It can be checked before passing to this function.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Radio capabilities frame is updated to use common descriptor
structure. Also, few changes to this frame is done like hardware
queues are increase to 12 from 8, default channel number is included.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For all TX command packets immediate wakeup bit needs to be
set in descriptor. This will make sure device will wakeup if it
is in any sleep state. Priority of the packet is also set.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All internal management packets (command packets) use some common
fields and some packet specific fields for packet descriptors.
This patch adds some common structures which are needed for all
command packets.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have now added separate lock for Rx. This lock is used to protect
tx path only
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Deadlock issue is observed during our stress tests. The root
cause for the issue is same lock is used between tx and rx threads.
This patch adds a separate mutex lock for rx thread to resolve
the problem.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer firmware sends information about number of blocks through
interrupt only. We don't need to read extra register for this.
This patch adds needed driver changes for this enhancment. The
change here is backward compatible
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO host is already claimed in our interrupt handler. Some lower
level APIs claims host while performing SDIO read or write operations.
Let's use sdio_irq_task variable to check if we are in interrupt
context and claim/release the host accordingly.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable in_sdio_litefi_irq is renamed to sdio_irq_task,
as it is more relevant here.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data packet descriptor preparation code is moved a separate
function.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch covers some enhancements in data packet descriptor
preparation especially for EAPOL, multicast/broadcast packets.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently this descriptor is prepared with the help of __le16
pointer. This patch makes use of a structure to prepare the
descriptor in a cleaner way.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Management descriptor preparation is move to a separate function
as it will be called from a different context in upcoming patches.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently this descriptor is prepared with the help of __le16
pointer. This patch makes use of a structure to prepare the
descriptor in a cleaner way.
Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
immediate wakeup bit is set while sending internal management
frame to the firmware.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Till now only management packets were handled. Let's enhance
the logic for choosing endpoint to accommodate other packets.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These endpoints are for WLAN and BT protocols.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maximum valid queue number is 0x5. So anding with 0x7 should be
ok here.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB headroom is added while submitting the data to URB as per
firmware's requirement. This logic is moved to rsi_usb_card_write() so
that caller need not worry about it.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to reset the chip in teardown path so that it can work
next time when driver is loaded. This patch adds support for this
reset configuration for USB.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes it's observed that we get interrupt/Rx frame when device is
already detached from mac80211. In this case couple of error messages
are displayed in dmesg log. This patch corrects the order so that
disconnection will happen cleanly
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to reset the chip in teardown path so that it can work
next time when driver is loaded. This patch adds support for
this reset configuration for SDIO.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
card reset is not working with recent kernels. Using
host->card->ocr instead of host->ocr_avail solved the problem.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
EEPROM read frame is sent during device initialization to read mac address.
The format of the frame is modified in firmware to include eeprom length
and offset. This frame does not return firmware version now. Also same
frame is sent again to read rf type and band information.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever new fsm_state enum element is added, fsm_state array
also needs to be updated. If this change is missed, we may end
up doing invalid access in array. BUILD_BUG_ON check will help
to avoid this problem.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to a bugfix in wireless tree and the commit mentioned below a merge
was needed which went haywire. So the submitted change resulted in the
function brcmf_sdiod_sgtable_alloc() being called twice during the probe
thus leaking the memory of the first call.
Cc: stable@vger.kernel.org # 4.6.x
Fixes: 4d79289598 ("brcmfmac: switch to new platform data")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit to rework the headroom check in start_xmit() now calls
pxskb_expand_head() unconditionally if the header is CoW. Unfortunately,
it does so with the delta between the extant headroom and the header
length, which may be negative if there is already sufficient headroom.
pskb_expand_head() does allow for size being 0, in which case it just
copies, so clamp the header delta to zero.
Opening Chrome (and all my tabs) on a PCIE device was enough to reliably
hit this.
Fixes: 270a6c1f65 ("brcmfmac: rework headroom check in .start_xmit()")
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code kfree's entry and then dereferences it by accessing
entry->bssid. Avoid the dereference-after-free by moving the kfree
after the access to entry->bssid.
Detected by CoverityScan, CID#1448600 ("Read from pointer after free")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex records information about various channels as it receives scan
information. It does this by appending to a buffer that was sized
to the max number of supported channels on any band, but there are
numerous problems:
(a) scans can return info from more than one band (e.g., both 2.4 and 5
GHz), so the determined "max" is not large enough
(b) some firmware appears to return multiple results for a given
channel, so the max *really* isn't large enough
(c) there is no bounds checking when stashing these stats, so problems
(a) and (b) can easily lead to buffer overflows
Let's patch this by setting a slightly-more-correct max (that accounts
for a combination of both 2.4G and 5G bands) and adding a bounds check
when writing to our statistics buffer.
Due to problem (b), we still might not properly report all known survey
information (e.g., with "iw <dev> survey dump"), since duplicate results
(or otherwise "larger than expected" results) will cause some
truncation. But that's a problem for a future bugfix.
(And because of this known deficiency, only log the excess at the WARN
level, since that isn't visible by default in this driver and would
otherwise be a bit too noisy.)
Fixes: bf35443314 ("mwifiex: channel statistics support for mwifiex")
Cc: <stable@vger.kernel.org>
Cc: Avinash Patil <patila@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
we can use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
1. drivers/net/appletalk/ipddp.c
2. drivers/net/wireless/broadcom/brcm80211/brcmfmac/debug.c
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_trace_data is somewhat confusing. It returns a bool
that tells if the payload of the skb should be added to
the tx_data event. If it returns false, then the payload
of the skb is added to the tx event.
The purpose is to be able to start tracing with
-e iwlwifi
and record non-data packets only which saves bandwidth.
Since EAPOLs are important, seldom and not real data
packet (despite being WiFi data packets), they are
included in tx event and thus iwl_trace_data returns false
on those. This last part was buggy, and because of that,
all the data packets were included in the tx event.
Fix that.
Fixes: 0c4cb7314d ("iwlwifi: tracing: decouple from mac80211")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
a few lines earlier in the function.
Cc: <stable@vger.kernel.org>
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit f95d95a7cd.
With commit f95d95a7cd ("rtlwifi: btcoex: rtl8723be: fix ant_sel not
work"), the kernel has a NULL pointer dereference oops. This content and
the proper fix will be included in a later patch.
Fixes: f95d95a7cd ("rtlwifi: btcoex: rtl8723be: fix ant_sel not work")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recent change in brcmf_sdio_txpkt_hdalign() changed the
behavior and now always returns 0. This resulted in a
regression which basically renders the device useless.
Fixes: 270a6c1f65 ("brcmfmac: rework headroom check in .start_xmit()")
Reported-by: S. Gilles <sgilles@math.umd.edu>
Tested-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove useless local variables last_read_point and last_txw_point and
the code related.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary static on local function pointer _writer_.
Such pointer is initialized before being used, on every
execution path throughout the function. The static has no
benefit and, removing it reduces the object file size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see a significant difference in the object
file size. This log is the output of the size command, before and after
the code change:
before:
text data bss dec hex filename
113797 19152 1216 134165 20c15 drivers/net/wireless/cisco/airo.o
after:
text data bss dec hex filename
113881 19096 1152 134129 20bf1 drivers/net/wireless/cisco/airo.o
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate array glrt_table on the stack but make it static.
Makes the object code a smaller by over 670 bytes:
Before:
text data bss dec hex filename
131772 4733 0 136505 21539 rt2800lib.o
After:
text data bss dec hex filename
131043 4789 0 135832 21298 rt2800lib.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304). We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280. However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.
memcpy(action_frame->data, &buf[DOT11_MGMT_HDR_LEN],
le16_to_cpu(action_frame->len));
Cc: stable@vger.kernel.org # 3.9.x
Fixes: 18e2f61db3 ("brcmfmac: P2P action frame tx.")
Reported-by: "freenerguo(郭大兴)" <freenerguo@tencent.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All wmi_services are not printing when we give below command.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/wmi_services
This patch increases the buffer_len to 8192 to print all the wmi_services.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Copy engine is a host to target communication interface
between wlan firmware and wlan wcn3990 platform driver. Add copy
engine register map for wcn3990 wlan module. This add support
for the copy engine source/destination ring configuration for
wcn3990 chipset.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove bus specific dependencies from CE layer
to have common CE layer across multiple targets.
This is required for adding support for WCN3990
chipset support as WCN3990 chipset uses SNOC
bus interface with Copy Engine endpoint.
Signed-off-by: Govind Singh <govinds@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 59ae1d127a ("networking: introduce and use skb_put_data()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/wmi.c:3308: code indent should use tabs where possible
Fix that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
The pci_error_handlers->reset_notify() method had a flag to indicate
whether to prepare for or clean up after a reset. The prepare and done
cases have no shared functionality whatsoever, so split them into separate
methods.
[bhelgaas: changelog, update locking comments]
Link: http://lkml.kernel.org/r/20170601111039.8913-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* Some important fixes for 9000 HW;
* FW API changes for the upcoming -30 ucode release;
* A few new PCI IDs for 9000 series;
* Reorganization of common files;
* Some more fixes and improvements here and there
* Initialization and other important fixes for 9000 series;
* Support for version 30 of the FW API for 8000 and 9000 series;
-----BEGIN PGP SIGNATURE-----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=f5vG
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-30' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Final set of patches for 4.13
* Some important fixes for 9000 HW;
* FW API changes for the upcoming -30 ucode release;
* A few new PCI IDs for 9000 series;
* Reorganization of common files;
* Some more fixes and improvements here and there
* Initialization and other important fixes for 9000 series;
* Support for version 30 of the FW API for 8000 and 9000 series;
We should not copy the MCS set from hostapd RX-STBC. We
have to just use the MCS set supported by the hardware.
This fixes an issue, where mwifiex is advertising wrong
MCS sets in beacons.
Fixes: 474a41e94d ("mwifiex: update MCS set as per RX-STBC bit from hostapd")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver used cfg80211_connect_result() which is basically a wrapper
around cfg80211_connect_done() passing a subset of the information that
can be passed. For upcoming functionality this is not sufficient so
switching to use cfg80211_connect_done().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding callbacks for PMK provisioning. If firmware supports offloading
it is indicated to user-space that 802.1X offload is supported.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware may have supplicant code built-in. This is detected
by the driver and indicated in the wiphy features flags. User-space
can use this flag to determine whether or not to provide the
pre-shared key material in the nl80211 CONNECT command.
Reviewed-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f4 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When hostapd adds a station, it does so before sending the association
response frame, so that it can indicate the correct status code in the
response.
However, when this then fails, or the association response already is
a reject for some other reason, then there's no station entry and thus
no per-station management queue to send the response on and it must be
sent on the probe response queue. The code should therefore not warn.
In theory, we could check and warn if the status code is success, but
that seems excessive, so just relax the check to allow any association
response frames.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only a000-series devices were going to use this, but actually
initialize using the context info, which includes paging, so
this code is never invoked; remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we now support 8 device families, move their configuration
files into a new subdirectory "cfg".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This structure represents V2, V1 has the three last fields missing.
Rename it to be more accurate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the first frame on a given TID is received with seqno 0 and needed
to be retransmitted, we erroneously drop it because the deduplication
data is initialized to zero, and then comparing
if (unlikely(ieee80211_has_retry(hdr->frame_control) &&
dup_data->last_seq[tid] == hdr->seq_ctrl &&
dup_data->last_sub_frame[tid] >= sub_frame_idx))
return true;
will return in iwl_mvm_is_dup() since last_sub_frame is also set to
zero, and sub_frame_idx is usually zero since this only covers the
relatively rare case of A-MSDU.
Fix this by initializing the last_seq array to 0xffff, which is an
impossible value for hdr->seq_ctrl to have here because the lower
four bits are the fragment number, and fragments aren't handled in
this code but go to mac80211 instead.
Fixes: a571f5f635 ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In commit b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work
as expected"), the code was changed to make the stop conditional
on not having failed (and on not having init_dbg), which doesn't
make sense - we should stop the device regardless of failures.
Failure to do so is leading to the device being enabled when it
shouldn't be, and - if it gets re-enabled later - the new context
info code gets confused as paging data wasn't freed.
Remove the invalid error condition again.
Fixes: b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work as expected")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.
Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.
While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print out both queue IDs to be able to see what went wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new a000 2ax series and add
the five PCI ID for it.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no reason to pass mvm and trig as parameters to the macro,
since it will be expanded inside the function itself. Also remove the
bogus buf parameter which doesn't exist and is not used.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The sta_id variable is used as an index in an array, should be unsigned.
Found by Klocwork.
Fixes: 9f9af3d7d3 ("iwlwifi: mvm: re-aggregate shared queue after unsharing")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A hardware issue on 9000 series devices sometimes causes RF-kill
interrupts to not be propagated to the host properly if ASPM is
enabled. Work around this by setting the right hardware bit to
allow it to interrupt the host for this reason (rfkill).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a hardware issue, certain power saving had to be
disabled. However, this issue was fixed in B-step, so the
workaround only needs to apply to A-step.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some static checkers (e.g. smatch) complain if a non-constant
format string is used, even if that's a static const variable.
Since there's no impact on code generation, just change those
format strings to be macros.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the kernel-doc, and remove some fields even the firmware doesn't
use in ToF, RX, scan, station and generic FW APIS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix various "Excess struct/union/enum/typedef member '...' description
in '...'" warnings from kernel-doc, mostly caused by typos.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a debugfs entry to get a verbose description of the power settings
used in each band with the currently selected SAR geographic profile.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are going to add debugfs entry to retrieve the current geographic
profile being used in the FW. Currently the driver reads those tables
from the BIOS and passes them to the FW.
To prepare for this retrieving we want to store those
tables in the driver.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trivial fix to spelling mistake in mwifiex_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check return value from call to wl18xx_top_reg_write(),
so in case of error jump to goto label out and return.
Also, remove unnecessary value check before goto label out.
Addresses-Coverity-ID: 1226938
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kstrtoul() test was reversed so this always returned -ENOTSUPP.
Fixes: 27d7f47756 ("net: wireless: replace strict_strtoul() with kstrtoul()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Declare hwbus_ops structures as const as they are only passed as an
argument to the function cw1200_core_probe. This argument is of type
const. So, make these structures const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two recent commits added new RSI_FSM_STATES (namely FSM_FW_NOT_LOADED
and FSM_COMMON_DEV_PARAMS_SENT) and the corresponding table fsm_state
was not updated to match. This can lead to an array overrun when
accessing the latter two states in fsm_state. Fix this by adding in
the missing states.
Detected by CoverityScan, CID#1398379 ("Illegal address computation")
Fixes: 9920322ccd ("rsi: add tx frame for common device configuration")
Fixes: 015e367494 ("rsi: Register interrupt handler before firmware load")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 9cc4b7cb86 ("brcmfmac: Make skb header writable
before use") the headroom usage has been fixed. However, the
driver was keeping statistics that got lost. So reworking the
code so we get those driver statistics back for debugging.
Cc: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The statistic counter is used in common layer and in the bus layer
in different thread contexts so change to use atomic operations.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A couple of old fields were still described and one field was not
described.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When user adds a virtual interface driver will set the
bss_type to the iface_type given by the user. When
supplicant is started on the same interface, a call to
change_virtual_intf will be triggered if if_type is not
NL80211_IFTYPE_STATION. Here driver should not update
it's bss_type, because bss_type is intended to indicate
the original iface_type and changing the same will defeat
the purpose of creating this interface.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If wifi is in 4way, btcoex give wifi higher priority to use antenna.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If there are many AP (dirty environment), we use another strategy set
to resolve coex issue.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will use return value to handle error case.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return value may be false in some situations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify 8723be and 8192e only.
8812/8821 do IQK in DM, so we may do it later.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this case, BTC asks to enter/leave PS mode frequently to cause A2DP
choppy.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value ret is unitialized and garbage is being returned
for the three different error conditions when setting up the PCIe
BARs. Fix this by initializing ret to -ENOMEM to indicate that
the BARs failed to be setup correctly.
Detected by CoverityScan, CID#1437563 ("Unitialized scalar variable")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Value assigned to variable offset at line 551 is overwritten at line 562,
before it can be used. This makes such variable assignment useless.
Addresses-Coverity-ID: 1226941
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the following spelling mistakes in messages:
syncronise -> synchronize
unusally -> unusually
addrress -> address
inverval -> interval
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move ath9k_rng_stop/ath9k_rng_start pair into critical section,
use mutex_lock to void potential race accessing.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the worst case, ath9k_rng_stop() may take 10s to stop rng kthread.
The time is too long for users, use wait_event_interruptible_timeout()
instead of msleep_interruptible(), wakup immediately once
kthread_should_stop() is true.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The hard coded register 0x9864 and 0x9924 are invalid
for ar9300 chips.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One scenario that could lead to UAF is two threads writing
simultaneously to the "tx99" debug file. One of them would
set the "start" value to true and follow to ath9k_tx99_init().
Inside the function it would set the sc->tx99_state to true
after allocating sc->tx99skb. Then, the other thread would
execute write_file_tx99() and call ath9k_tx99_deinit().
sc->tx99_state would be freed. After that, the first thread
would continue inside ath9k_tx99_init() and call
r = ath9k_tx99_send(sc, sc->tx99_skb, &txctl);
that would make use of the freed sc->tx99_skb memory.
Cc: <stable@vger.kernel.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
-----BEGIN PGP SIGNATURE-----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=DdqX
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
More iwlwifi patches for 4.13
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
If 'wiphy_new()' fails, we leak 'ops'. Add a new label in the error
handling path to free it in such a case.
Cc: stable@vger.kernel.org
Fixes: 5c22fb8510 ("brcmfmac: add wowl gtk rekeying offload support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function brcmf_net_attach() can only fail when register_netdevice()
fails. When this happens register_netdevice() calls priv_destructor, ie.
brcmf_cfg80211_free_netdev() freeing the vif instance. Also upon this
failure brcmf_net_attach() calls free_netdev(). However, callers are also
doing cleanup resulting in double free. In some places they need netdev
private space as it holds parameters to communicate with the device. So
we want to do the cleanup only in callers of brcmf_net_attach() by making
the following changes:
- set priv_destructor after register_netdevice() succeeds.
- remove call to free_netdev() in brcmf_net_attach().
- call free_netdev() in brcmf_net_detach() for unregistered netdev.
- add free_netdev() if brcmf_net_attach() fails for a created interface.
Fixes: cf124db566 ("net: Fix inconsistent teardown and release of private netdev state.")
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
=Fd/c
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to TX through a monitor interface, the
conditions in iwl_mvm_tx_skb_non_sta() don't match
and the frame tries to go out from an usued TXQ.
Add a check for monitor iface, and use the AUX queue
in such a case.
In non-DQA mode the frame is sent through the
static-allocated queues anyway, so the problem is
in DQA mode only.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware crashes, the transmit queues can't make
any progress. This is why we stop the counter that monitor
the transmit queues' activity.
The call that notifies the error to the op_mode may take
a bit of time, so stop the timer of the transmit queues
earlier.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver prints "L1 Enabled - LTR Enabled" all the time as dev_info,
which is just useless noise in most cases. Convert this to
IWL_DEBUG_POWER() so we don't pollute the log unnecessarily but still
can get this info on demand.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's sometimes hard to find out which HW address the iwlwifi device is
using, for instance when reading crouded sniffer logs. To make it
easier, print out an info level message with the HW address as soon as
we know it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API allows flushing queues based on station ID and TID in A000
devices. One reason for using this is that tfd_queue_mask is only good
for 32 queues, which is not enough for A000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get an ASSERT, the fw_dump_desc pointer points to
iwl_mvm_dump_desc_assert which can't be freed since it is
a global. We still need to NULL'ify the pointer when we
call iwl_mvm_free_fw_dump_desc otherwise we will hit
int iwl_mvm_fw_dbg_collect_desc(struct iwl_mvm *mvm,
const struct iwl_mvm_dump_desc *desc,
const struct iwl_fw_dbg_trigger_tlv *trigger)
{
<snip>
if (WARN_ON(mvm->fw_dump_desc))
iwl_mvm_free_fw_dump_desc(mvm);
Fixes: b6eaa45aa1 ("iwlwifi: mvm: add the cause of the firmware dump in the dump")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When updating the mac context after association,
assoc_beacon_arrive_time is not being set, which causes the FW to
set a wrong TSF to the MAC.
Fix this by setting the assoc_beacon_arrive_time when updating the
mac context after association.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing ever checks the return value of iwl_pcie_apm_stop_master(),
so there's no point in it having one - make it return void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we need to move the scheduler write pointer by
steps of 0x40, 0x80 or 0xc0, the scheduler gets stuck.
This leads to hardware error interrupts with status:
0x5A5A5A5A or alike.
In order to work around this, detect in the transport
layer that we are going to hit this case and tell iwlmvm
to increment the sequence number of the packets. This
allows to keep the requirement that the WiFi sequence
number is in sync with the index in the scheduler Tx queue
and it also allows to avoid the problematic sequence.
This means that from time to time, we will start a queue
from ssn + 1, but that shouldn't be a problem since we
don't switch to new queues for AMPDU now that we have
DQA which allows to keep the same queue while toggling
the AMPDU state.
This bug has been fixed on 9000 devices and up.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A TID may not have traffic but still have a BA agreement
active (or being setup / torn down) since a BA agreement
can be triggered by a debugfs hook.
Just avoid to consider such a TID as inactive to make the
logic safer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the hardware is stuck, we can't read any of the memory we need to
dump it, so we end up printing only 0xa5a5a5a5, which is useless.
To solve this, poke the hardware by triggering a reset and re-enabling
the clocks if we detect a HW error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we started using threaded irqs, all the opmode calls were changed
to be called with local_bh disabled. The reason for this was it was
that mac80211 needs that. When we are handling FW errors, mac80211 is
not involved, so we don't need it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In BSS mode in the disconnection flow, mac80211 removes
the AP station before the vif is set to unassociated.
Our firmware wants it the other way around: first set
the vif as unassociated, and then remove the AP station.
In order to bridge between those two different behaviors,
iwlmvm doesn't remove the station from the firmware when
mac80211 removes it, but only after the vif is set to
unassociated. The implementation is in
iwl_mvm_bss_info_changed_station:
if (assoc state was modified && mvmvif->ap_sta_id is VALID
&& assoc state is now UNASSC)
remove_the_station_from_the_firmware()
During the recovery flow, mac80211 re-adds the AP station
and then reconfigures the vif. Since the vif is not
associated, and then, we enter the if above (which was
intended to be taken in the disconnection flow only) and
remove the station we just added. This defeats the
recovery flow.
Fix this by not removing the AP station in this flow if
we are in recovery flow.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We allocate nvm_data in iwl_mvm_nvm_get_from_fw(). If something goes
wrong after the allocation (i.e. if no valid MAC address is valid), we
should free nvm_data before returning an error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function just calls kfree(), so it only obscures the code without
bringing any benefits. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Properly document the transmit buffer bits using an enum and
kernel-doc documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add kernel-doc documentation for enum iwl_debug_cmds, linking the
structures used by the commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This improves documentation, since kernel-doc can't deal with the
union well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To stop and start the FW monitor in the 7000 HW
family we need to use a different bit, otherwise
after stopping it for the first time - it won't
get restarted. Use the correct bitmask.
Note: This fix is only for DRAM collection mode.
For other modes, an additional fix will be
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the enum link by adding the missing & and provide the link
to the TX response documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the command name is printed on command completion, the wrong
group is used, leading to the wrong name being printed. Fix this
by using the group ID without inappropriately mangling it through
iwl_cmd_groupid() - it's already a u8. Also, while at it, use it
from the same place as the command ID, everything else is just
confusing.
Fixes: ab02165cce ("iwlwifi: add wide firmware command infrastructure for TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending non-linear SKBs that should be included in the regular
TX tracing completely (and not be pushed into the tx_data tracing),
the (tracing) code didn't correctly take the fact that they were
non-linear into account and added only the skb head portion.
This probably never really triggered, since those frames we want
traced fully are most likely linear anyway, but the code gets easier
to understand and we lose an argument to the tracing function, so
overall fixing this is better.
Fixes: 206eea7833 ("iwlwifi: pcie: support frag SKBs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to calculate the data_len outside of the tracepoint,
since it's always skb->len - hdr_len, which are both available inside.
Simplify the callers and move the calculation in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Show the name of the member (scanned_channels) that provides the
length with some better markup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use kstrtou32_from_user() in debugfs instead of open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.
Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we happen to be in or get into the queue sync when RF-kill
is asserted, we return from there and warn since there are
still queue sync notifications outstanding. These can't ever
come though, because we're in RF-kill, so don't WARN then.
While at it, also move the warning to the appropriate place,
if the request is not synchronous then we shouldn't warn, but
currently always will.
To make it fast, also trigger the waitq when on rfkill assert.
Fixes: 0636b93821 ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in duplicating exactly the same code here
for legacy and MSI-X interrupts, so pull it out into a new
function to call in both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case that rate's antenna is wrong at the init stage, it's
very hard to say what went wrong. Add debug data to the already
existing WARN_ON_ONCE.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some static checkers (e.g. smatch) complain about the logic, saying that
resp_cp might be leaked. Clearly that isn't true, but making the logic
easier to follow does not result in any significant code changes and makes
the code more readable by moving the NULL check closer to its source.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware moved the development from a0 MAC to z0.
z0 is using the same RFID and device ID as a0 so we only
need to switch the name.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New FW versions require the D0I3_END_CMD to be sent as the first
command to the FW in the resume flow. If the TLV is set, send that
command first, otherwise keep the original behavior (i.e. send last).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no need to send D0I3_END_CMD as ASYNC during the system
resume flow. Additionally, the other flags used are meaningless in
this case (they were just copied from the runtime resume flow), so
remove them all.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Shaul reported that when iwlmvm was sending beacons, it didn't properly
also take ownership of the probe responses. This is because the whole
mac80211 callback (tx_last_beacon) wasn't implemented. Fix that to make
IBSS discovery work better.
Reported-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's safer to use scnprintf() here because the buffer might
be too short for the full format strings. In most cases
this isn't true because of external limits on the values.
In one case, this fixes a stack data leak.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid one kind of symbol shadowing another in iwl_mvm_flush_sta()
by renaming the function parameter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The queue ID should never be 512 either, so correct the check
to be >= instead of just >.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we exit if buf->num_stored is 0, there's no need to
check it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending a Tx Command with a Tx packet, we allocate the
Tx command separately from the payload of the packet.
The WiFi MAC header is then copied into the buffer that was
allocated for the Tx Command. This means that this buffer
needs to be big enough to contain both. This is why it is
allocated with iwl_trans_alloc_tx_cmd which returns a
pointer to a newly allocated not zeroed struct
iwl_device_cmd.
The Tx command has a few bit fields and hence it needs to
be zeroed, but all the rest of the buffer doesn't need to
be zeroed since it will either be memcopy'ed with the MAC
header, or not even sent to the device.
This means that we don't need to zero all the
iwl_device_cmd structure, but rather only the size of
the iwl_tx_cmd structure.
Since sizeof(iwl_tx_cmd) - sizeof(iwl_tx_cmd) is about
260 bytes, this can avoid touching 4 cache lines for each
packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Install GTKs on AP side for new TX API.
Don't add IV space, it's added by the HW.
While at that fix GCMP abnd GCMP-256 GTK installation
which work similarly to the new TX API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If FW isn't alive, trying to collect debug data will
result in errors both in driver and in the collected
data, so just warn and leave the collecting function
in this case.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Contrary to what some of the comments say, if rfkill was
asserted the transport will return -ERFKILL instead of
success, if CMD_WANT_SKB was set, so it's not necessary
to check cmd.resp_pkt for being NULL if the return code
was success.
Validate that this is true in iwl_trans_send_cmd().
Most of the other code modifications were done with the
following spatch:
@@
struct iwl_host_cmd cmd;
identifier pkt;
@@
<...
(
pkt = cmd.resp_pkt;
...
-if (!pkt) { ... }
|
pkt = cmd.resp_pkt;
...
-if (WARN_ON(!pkt)) { ... }
|
-if (!cmd.resp_pkt) { ... }
)
...>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, there is no need to wait for the TXQ to
clear out after getting a DELBA, since traffic can
continue running on the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ath.git patches for 4.13. Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes spin-forever in irq handler when IRQ is already asserted
at request_irq() time.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To yield better user experience, have btcoex control LPS's parameters.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If LPS is controlled by btcoex, this function tell driver LPS is on or off.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If RX ampdu is too long, BT will have less time.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add btcoex record pwr mode to control LPS's parameters and share time
with BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We extend types of special packets to a enumeration from boolean value.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using EAPOL to do a PTK rekey, there is a possible race condition.
When msg 3/4 is received, the supplicant will send msg 4/4 and install
the new key immediately; however, the driver must make sure that msg 4/4
is sent before installing the new key. We use TX report to ensure it is
sent.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The number of debugging conditions now exceeds the capabilities of a
32-bit word.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the driver itself will enter power saving mode dynamically
according to the traffic, we set hw capability SUPPORTS_PS and
SUPPORTS_DYNAMIC_PS in case of fwctrl_lps.
The process IEEE80211_CONF_CHANGE_PS in op_config is used by
SW-LPS only, so we add constraints to avoid errors.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: vincent_fann <vincent_fann@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To make ant_sel work, we should call power_on_setting to set antenna
correctly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit fixies two problems. The first one is interface types
(e.g. PCI) that are used to switch antenna, and the second is to add
wifi_only parameter to give correct state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New btcoex add a function 'bind' to connect adapter, so we should call
it during initializing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After successful loading of firmware, a CARD READY indication is
received by host. Common device configuration parameters are sent
to the device after this. It includes information like device
operating mode (Wi-Fi alone or BT coex), power save related
parameters, GPIO information etc. As device supports BT coex,
this frame is send in COEX queue initially. Based on the operating
mode, CARD READY indication is received from each protocol module
in firmware i.e. WLAN, BT.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Boot parameters are changed in new firmware. Also three
new sdio sleep parameters are added for ultra low power
save.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before firmware load, sometimes false interrupts are received.
System hang is observed if interrupt handler is not registered
to receive these interrupts. Hence interrupt handler registration
is moved before firmware load. We will drop these false interrupts
as these are not from the device.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently macros are used for FSM states. We will replace
it with enum so that new state can be added easily without
worrying about macro value.
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb device id and vendor id for RS9113 chipset are included.
So it can be used through usb interface.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
debugfs_remove already check mwifiex_dfs_dir, so remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch uses WARN level is not printed by default.
In some cases, some boards have always met the unused log be printed as
follows.
...
[23193.523182] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2 & channel=13 freq=0
[23378.633684] mwifiex_pcie 0000:01:00.0: mwifiex_get_cfp:
cannot find cfp by band 2 & channel=13 freq=0
Due to we used the wifi default area was US and didn't support 12~14
channels. As Frequencies:
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Also, as the commit 1b499cb72f
("mwifiex: disable channel filtering feature in firmware"), it proved to
be a feature to get better scan result from overlapping channel.
Even there could be AP from overlapping channel (might be 12/13/14
in this case), it will be filtered depend on reg domain rules.
e.g:
...
if (ch->flags & IEEE80211_CHAN_DISABLED)
continue;
So it should not been an ERROR, use the WARN level to instead it for now.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Acked-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The REG_USTIME_TSF (US Time Tuning for TSF) definition of Realtek chips
should be 0x55C.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcm43430 chip needs different firmware files for chip revision 0
and 1. The file currently in linux-firmware is for revision 1 only.
This commit makes brcmfmac request brcmfmac43430a0-sdio.bin instead
of brcmfmac43430-sdio.bin for revision 0 chips.
Note that the behavior for revision 1 chips is not changed, ideally those
would load brcmfmac43430a1-sdio.bin, but that will break existing setups.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless drivers should not be using ioctl interface,
hence remove this interface for wil6210 driver.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After calling platform_ops.uninit() it is still possible to invoke
platform callbacks.
To prevent this, zero platform_ops right after invoking uninit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 supports VHT80 with 2x2. But it only support 1x1 with VHT160 or
VHT80+80. Inform userspace and the the QCA firmware about that limitation
whenever VHT80+80 or VHT160 is configured.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9984 hardware can do 4x4 at 80Mhz, but only 2x2 at 160Mhz.
First, report this to user-space by setting the max-tx-speed
and max-rx-speed vht capabilities.
Second, if the peer rx-speed is configured, and if we
are in 160 or 80+80 mode, and the peer rx-speed matches
the max speed for 2x2 or 1x1 at 160Mhz (long guard interval),
then use that info to set the peer_bw_rxnss_override appropriately.
Without this, a 9984 firmware will not use 2x2 ratesets when
transmitting to peer (it will be stuck at 1x1), because
the firmware would not have configured the rxnss_override.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: rebase, cleanup, drop 160Mhz workaround cleanup]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[kvalo@qca.qualcomm.com: use hw_params, rename the title]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath10k firmware doesn't announce its VHT channel width capabilities in
the vht_cap information from the "service ready event" arguments. The
driver must therefore check whether the 160MHz short GI bit is set and
whether the driver still doesn't set the bits for the 160/80+80 MHz
capabilities.
The two bits for the channel width are a two bit integer and not two
separate bits which cannot be parsed without the knowledge of the other
bit. Using IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ (b10..) as a
mask for this task doesn't make any sense. The correct mask for the VHT
channel width should be used instead to make this check more readable.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[sven.eckelmann@openmesh.com: separate 160Mhz workaround cleanup, add commit
message]
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Two important fixes for brcmfmac. The rest of the brcmfmac patches are
either code preparation and fixing a new build warning.
brcmfmac
* fix a NULL pointer dereference during resume
* fix a NULL pointer dereference with USB devices, a regression from
v4.12-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZSSOQAAoJEG4XJFUm622browIAKdoXRzDj9t/r1s9UY+Fvm2w
YLiVCEy3Z/enF2iQcdmBC+uHNeaVWGctvjljxWwL6UsWx+Dl0/Dxcfilnan7SrYI
x5ysh+K4vfQ3oOf314vRuw+7u/h1WgobxdD9dgv7+C8yA7AIgHJlzZeM6PYdhibE
cEw/BOKDMDQ9NDnTJmaUmUogB/92TP3f5ACrNBe11kyPBtHuYFhNzee3PJQ3xP3I
D2knpUD3LtHhPDRC7ku9tpsmBpGHbOwGPHkLW1i9YhjHPe5ecmfvXtc7o/yUlLZK
f+xOMNuktUwsTjV0qhRnwx6Z2uJS1LlCmqVncaZIn7f+BYhORmTYIo45x628FGg=
=D6GF
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-06-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.12
Two important fixes for brcmfmac. The rest of the brcmfmac patches are
either code preparation and fixing a new build warning.
brcmfmac
* fix a NULL pointer dereference during resume
* fix a NULL pointer dereference with USB devices, a regression from
v4.12-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename:
wait_queue_t => wait_queue_entry_t
'wait_queue_t' was always a slight misnomer: its name implies that it's a "queue",
but in reality it's a queue *entry*. The 'real' queue is the wait queue head,
which had to carry the name.
Start sorting this out by renaming it to 'wait_queue_entry_t'.
This also allows the real structure name 'struct __wait_queue' to
lose its double underscore and become 'struct wait_queue_entry',
which is the more canonical nomenclature for such data types.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function
'brcmf_usb_probe_phase2':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:1198:2:
warning: 'devinfo' may be used uninitialized in this function
[-Wmaybe-uninitialized]
mutex_unlock(&devinfo->dev_init_lock);
Fixes: 6d0507a777 ("brcmfmac: add parameter to pass error code in firmware callback")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in ath6kl_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Report per chain RSSI to mac80211.
Signed-off-by: Norik Dzhandzhapanyan <norikd@gmail.com>
[kvalo@qca.qualcomm.com: fix conflicts and style]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define structures for the copy engine ctrl/misc registers,
that includes CE CMD halt, watermark source, watermark destination,
host IE ring, source, destination and dmax ring.
This adds support to avoid the conditional compilation,
code optimization and dynamic configuration of the copy engine
register map for respective hardware bus interface.
Signed-off-by: Sarada Prasanna Garnayak <c_sgarna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
USB devices rely on queuing functionality provided by the fwsignal
module regardless the mode fwsignal is operating in. For this some
data structure needs to be reserved which is tied to the interface,
which is done by brcmf_fws_add_interface(). However, it checks the
mode. Replace that by checking result from brcmf_fws_queue_skbs().
Otherwise the driver will crash in a null pointer dereference when
data is transmitted on the interface.
Fixes: fc0471e3e8 ("brcmfmac: ignore interfaces when fwsignal is disabled")
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When request firmware fails, brcmf_ops_sdio_remove is being called and
brcmf_bus freed. In such circumstancies if you do a suspend/resume cycle
the kernel hangs on resume due a NULL pointer dereference in resume
function. So in brcmf_sdio_firmware_callback() we need to unbind the
driver from both sdio_func devices when firmware load failure is indicated.
Cc: stable@vger.kernel.org # 4.9.x-
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When firmware loading failed the code used to unbind the device provided
by the calling code. However, for the sdio driver two devices are bound
and both need to be released upon failure. The callback has been extended
with parameter to pass error code so add that in this commit upon firmware
loading failure.
Cc: stable@vger.kernel.org # 4.9.x-
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extend the parameters in the firmware callback so it can be called
upon success and failure. This allows the caller to properly clear
all resources in the failure path. Right now the error code is
always zero, ie. success.
Cc: stable@vger.kernel.org # 4.9.x-
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the recently introduced helper to replace the pattern of
skb_put() && memset(), this transformation was done with the
following spatch:
@@
identifier p;
expression len;
expression skb;
@@
-p = skb_put(skb, len);
-memset(p, 0, len);
+p = skb_put_zero(skb, len);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary variable and refactor the code.
Addresses-Coverity-ID: 1365000
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Motorola Droid 4 uses a WL 1285C. With differences between
chips not being public let's add explicit binding for wl1285
instead of relying on wl1283 being very similar.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The semaphore 'async_sem' is used as a simple mutex, so
it should be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of rssi status, the btcoex also needs to get the link status of
the wifi. In addition, some of the rssi status can be merged into link
status.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These display functions are useless and will not be called in the
future.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When initializing, gather BT information in struct btcoexist and
provide them to wifi driver.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hook the external functions for newer ICs such as 8821a and 8192e.
Rename ex_halbtc8192e2ant_halt_notify to ex_btc8192e2ant_halt_notify.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the hardware is turned on and in the initialization stage, the PTA
circuit is unstable. Hence we need to force some hardware settings to
make sure the PTA circuit work correctly, otherwise it may affect the
user's experience.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hook the chip-specific PnP notify functions for the wifi driver to
notify btcoexistence.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The btcoex is sometimes unstable because there are some unexpected
behaviors before the firmware has been downloaded successfully.
Therefore we force the antenna path settings to avoid this, then let the
firmware control the btcoexistence when the firmware is ready.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These external functions are for BT-coexistence, so remove the "hal"
prefix for consistancy.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some external functions that have hardware dependency, we need to
know the type of the hardware before invoking them.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code allocates cmd_skb and then will leak this if band->band
is an illegal value. It is simpler to sanity check the band first before
allocating cmd_skb so that we don't have to free cmd_skb if an invalid
band occurs.
Detected by CoverityScan, CID#1437561 ("Resource Leak")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
function mwifiex_ret_pkt_aggr_ctrl can be made static as it does not
need to be in global scope.
Cleans up sparse warning: "symbol 'mwifiex_ret_pkt_aggr_ctrl' was not
declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
An earlier change to this function (3bdae81072) fixed a leak in the
case of an unsuccessful call to brcmf_sdiod_buffrw(). However, the
glom_skb buffer, used for emulating a scattering read, is never used
or referenced after its contents are copied into the destination
buffers, and therefore always needs to be freed by the end of the
function.
Fixes: 3bdae81072 ("brcmfmac: Fix glob_skb leak in brcmf_sdiod_recv_chain")
Fixes: a413e39a38 ("brcmfmac: fix brcmf_sdcard_recv_chain() for host without sg support")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Peter S. Housel <housel@acm.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix grammar issue in error message about ISO3166.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support to handle scheduled scan request containing BSSID in
the matchsets. The firmware can send event upon finding BSSIDs and
SSIDs. To get these in one event the bit REPORT_SEPARATELY needed
to be removed from the flags in brcmf_pno_config().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The request references kept in pno are accessed in user-space context
and in firmware event handler context. As such we need to protect it
with a lock. As both context allow sleep a mutex seems appropriate.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This change adds support for multi-scheduled scan in the driver. It
currently relies on g-scan support in firmware and will set struct
wiphy::max_sched_scan_reqs accordingly. This is limited to 16 concurrent
requests.
The firmware currently has a limit of 64 channels that can be configured
for all requests in total regardless whether there are duplicates. So if
a request uses 35 channels there are 29 channels left for another request.
When user-space does not specify any channels cfg80211 will add all
channels defined by the wiphy instance to the request, which makes
reaching the limit rather easy for dual-band devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAlk3AR8ACgkQoUecoho8
xfr21w//YzwKCVCR568wtQ0kZwLaPUos/FCeEgrFCpcAEe//wZZFZphH/z4mOLmX
xXRYmqYaQuztfqUKO/7Onw2djuXQNJJtHp+AdCCnzyMLKz6F6YbBG+M3755nM2Wl
XDVNbmRsmlGKvc2RCSoTSXSdNiT9TND9nYyzPFl/4x+fSD9olsjPvIVk1sNn2o69
znrcPJZJWVeYB/1uqLTqOQ0Xdm9r4tEYnnI+VsRMlwsOBQp6kgPMHEjoZdrV3RGI
qzgu0WNnAqqy1W2QOAi6iiU1jLm5VJ9CKyTT/m/4u9GypfUOm0mBKWuykB5klswH
6lJWz/P4dK7WZg7udCySeQrXbwiIlH0HF8uUoabDJHJd7LUXvEAljsYzG9B/cU0g
s4/2fA13eGDKf5vJULHQKLD4OJf82S7YhMiMM855pj/xVa1FZpupVACJ1cWik4n+
MlK8scXllrrjuFG1C7VDq7Jj3uY1ZxIN+TtuUl5vzgJ4n7buqqOcetDN07XqIwGZ
HLoA5uhdyr12mUDbtiicq9q/wu3bFD1CMDllINoBcmh7Psr1Vng0hhWsLJigvTUI
5+fKOYMNznjrBmcVvI/ZgRVW1Zo7+XCEOQpu25zOmoP/5vIpc2yA7kDvUgDfyzhw
3+KL+rw6IX3kfOWIuJTMq6iMtFIdRTc0K5zndC972maXUAE3wWY=
=oYeO
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi driver patches 4.13
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().
We are trying to get rid of DRIVER_ATTR(), and the ipw2x00 driver's
attributes can be trivially changed to use DRIVER_ATTR_RW().
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZPpCkAAoJEG4XJFUm622bUTMH/ipenw7p7otrhw9qtSBcqBRJ
hS+1i2J+VXDXptFng0ziPWVv6mvhANvBszuOmiNMOgqjx2HrVknwlKUKViklHN3p
E1PE3/A3bRpzBjMk4j8r/Z7VJK3rDa4WSi/AMJtqV9noNm5FfiOrCk7rXm2MLBns
x1Wyr/7OX12hiB4SCoOuOZqS/TvHlNCW71BoyRruq01N2MA1iSonLCYJbovgi7Ds
9acAY90PF8jLC+o7wxYkwuRqWncNhnKOsVNhc/6DKH91zB+C5sw2NGfD3WMfot/Z
9uC5nBWNadoLGi636y+9evIRgNAFCczCZZSUeY7jMWiVn7XyFy8zoc4fv2ZSBto=
=6md1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
When we removed dev_cmd_headroom, the check for dev_cmd_ptr == NULL
became unnecessary, since we just return dev_cmd_ptr anyway. Cleanup
the function to avoid useless code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The include in the deleted file are included in the fw-api.h file.
Which caused a cycle include in the dependencies.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware no longer uses this command group, so remove it from
the driver as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link from the TX_CMD enum value to the TX command structs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Document which structures are used with the command for
the A000 hardware flavour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to more clearly document which parts of this file
are firmware API and which are something else, split the
firmware API into a separate file to include here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The kernel-doc here is on an enum, so don't tag it as struct
but correctly as enum instead, preventing an error.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Clear the firmware running bit before flushing the FW (error) dump
work, because otherwise debugfs isn't blocked (previous patch) and
can cause a new work to be scheduled, which will then run after we
actually shut down the device, wreaking havoc. Clearing it ensures
that debugfs can't interfere anymore, and we can safely cancel or
flush the work struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Convert ucode_loaded to a status bit called FIRMWARE_RUNNING.
This will make it easier to clear this earlier, to avoid any
spurious accesses while shutting down, for example through
debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to refer to system_wq directly, use the provided
wrapper schedule_delayed_work().
Made with the following spatch:
@@
expression E,F;
@@
-queue_delayed_work(system_wq, E, F);
+schedule_delayed_work(E, F);
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Protect various debugfs files that need to communicate with the
firmware from being used when the firmware isn't running.
Some will just reject getting written to, while others that store
some state will simply store it and not apply it immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from the current list of PRPH that can't be
collected in A000 HW, the rest of the debug dump
data the driver collects is valid, so there is no
need to disable collection only because of this.
Disable PRPH collecting in A000 HW, and allow
collecting the rest of the debug data.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FH in A000 HW are placed in a different location,
and need to be read as prph, rather than direct.
Support A000 dumping as well as legacy.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two new device families to differentiate them from 8000.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case an assert happens on init flow, the current
driver powers down the NIC, except if iwlmvm modparam
init_dbg=1, and only on very specific flows.
Extend this capability to cover most failure cases
by keeping track of what init configurations have been
completed. This way, we can allow NOT powering down
the NIC, while making sure that when the driver is
removed we don't try to free resources that haven't
been allocated. (This can result in a kernel panic.)
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to NAN FW API change, add TLV in order to distiguish between the
2 API versions
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use transport configuration to determine DBGC support
instead of relying on device family.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't have any 8000 B-step right now, and there is no
firmware loading code for them anyway.
Further more, 9000 B-step devices will hit those code paths.
Remove code that was introduced only for 8000 B-step.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
NVM code is tightly coupled with 8000 family, while
it really refers to extended NVM format introduced
back then. Separate it to a configuration dependent
boolean, and rename defines accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is essentially the same code as gen1, except that it uses
gen2 functions and SW checksum is not included.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Document the structures used in RX and link them to the command ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enable offload assist for AMSDU when the AMSDU present flag is set.
Fixes: a830baba9c2e ("iwlwifi: mvm: support new TX API")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sending host command with CMD_WANT_SKB flag demands the release of the
response buffer with iwl_free_resp function.
The patch adds the memory release in all the relevant places
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a previous commit, we removed support for API versions earlier than
22 for these NICs. By mistake, the *_UCODE_API_MIN definitions were
set to 17. Fix that.
Fixes: 4b87e5af63 ("iwlwifi: remove support for fw older than -17 and -22")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Clear the struct so that all reserved fields are zero when we
send the struct down to the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_remove_sta_key() function handles removing a key when the
sta doesn't exist anymore. Mistakenly, this was changed to return an
error while fixing another bug.
If the mvm_sta doesn't exist, we continue normally, but just don't try
to remove the igtk key.
Fixes: cd4d23c1ea ("iwlwifi: mvm: Fix removal of IGTK")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.
Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
recording)
For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.
Fixes: 5c89e7bc55 ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.
Fixes: 7948b87308 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During d0i3 flow we flush all the queue except from the command queue.
Currently, in this flow the command queue is hard coded to 9.
In DQA the command queue number has changed from 9 to 0.
Fix that.
This fixes a problem in runtime PM resume flow.
Fixes: 097129c9e6 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Up until now, the driver was comparing the rate reported by the FW and
the rate of the latest LQ command to avoid processing data belonging
to the old LQ command. Recently, FW changed the meaning of the initial
rate field in tx response and it holds the actual rate (which is not
necessarily the initial rate of LQ's rate table). Use instead LQ cmd
color to be able to filter out tx responses/BA notifications which
where sent during earlier LQ commands' time frame.
This fixes some throughput degradation in noisy environments.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we have 512 queues, add a wait for single TX
queue to gen2.
This replaces gen1 wait_tx_queues_empty, which was limited
to 32 queues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix many kernel-doc warnings. In one case, this required adding
a new enum value to be able to document things properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This value is unused, and there's no reason we'd ever use it.
Just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Using %enum instead of &enum (and in one case, %struct) results in
the wrong parsing. Fix that so that if documentation is generated,
the result is clickable links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Integrated chip may have different HW and RF steps.
Currently, the driver supports only different HW steps.
Add logic to support different RF steps enables combining different
HW and RF steps.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In gen2, page dumping needs to be done in the trans
layer, as it is the one with access to the paging
pointers.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In gen2, page dumping should be done in transport
layer, since the addresses needed for the paging
mechanism reside there.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add documentation to a lot of command IDs that links to the
appropriate structure(s) used with those IDs. In one case,
actually add and use a new struct for that purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some values should be in enums so documentation can refer to
them, some values should be named for the same reason.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
