22000 devices (previously referenced as A000) can support
short transmit queues. This means that we have less DMA
descriptors (TFD) for those shorter queues.
Previous devices must still have 256 TFDs for each queue
even if those 256 TFDs point to fewer buffers.
When I introduced support for the short queues for 22000
I broke older devices by assuming that they can also have
less TFDs in their queues. This led to several problems:
1) the payload of the commands weren't unmapped properly
which caused the SWIOTLB to complain at some point.
2) the hardware could get confused and we get hardware
crashes.
The corresponding bugzilla entries are:
https://bugzilla.kernel.org/show_bug.cgi?id=198201https://bugzilla.kernel.org/show_bug.cgi?id=198265
Cc: stable@vger.kernel.org # 4.14+
Fixes: 4ecab56160 ("iwlwifi: pcie: support short Tx queues for A000 device family")
Reviewed-by: Sharon, Sara <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This aligns the code with the existing pattern to check
if the firmware has a certain capability.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently a new command was added to the firmware
for setting a MAC's low-latency mode. Use it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have TSO enabled, we might end up segmenting it and
queuing multiple packets before the queue is even enabled. This causes
a warning.
For example, when starting TCP traffic on a non-zero TID, the
first packets may not have DSCP and will be sent on TID 0, while
the actual data packets will be sent on the TID.
To prevent this, simply remove the warning.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This helps matching tx cmd with other trace events, like net_dev_xmit
and net_dev_queue etc.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't need the _enum suffix.
Also refer to &enum iwl_tlc_mng_vht_he_types instead
of %IWL_TLC_MNG_VALID_VHT_HE_TYPES_\*
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Latest firmware calculates both phases of the TKIP
field, so the TTAK ok flag is not needed and deprecated.
Support this API change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For sync we send a marker cmd every <defined throughout debugfs> seconds.
The trigger for getting gp2 clock values from the FW is set by
writing to debugfs a periodic time in seconds,
if value zero is written, only one request would be sent
and the timer would be canceled.
Also added a small infrastructure for debugfs runtime code.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The way p2p NoA is forced in SCM (used for WFA tests)
is by setting a quota < 100% (simulating DCM).
A test-mode command is used for setting the NoA params.
In that case, force quota update or nothing will happen
if there was no significant change in the quota
at that exact point (which is likely to be the case).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.
Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support internal debug data collection on 9000 and newer
devices.
The method for finding the base and end address has changed
on new HW's, so introduce a new version of debug destination
tlv.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidentally pushed a patch with CPTCFG (which is used in the
backports project) to the rs-fw.c file. Fix that to use CONFIG
instead.
Fixes: 9f66a397c8 ("iwlwifi: mvm: rs: add ops for the new rate scaling in the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When statistics are read from debugfs, make sure that they
are actually updated from the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If FW loads without a problem, leaving init_dbg on can
cause a confusion, since the user won't necessarily
remember it is still turned on, and there are flows in
which everything continues as usual, only without
stopping the device after INIT, even if there is no FW
assert. On 22000 HW, for instance, this causes a
warning, since the paging is getting initialized twice.
Solve the issue by making this module param effective
only if the FW indeed asserts during INIT.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending LQ command, verify the rate scaling is not in firmware.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch sends to the FW notification configuration command and
handles the update responses.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch adds rate scaling configuration command and
implements a few other handlers.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the series will fill in the implementation).
The decision which API to use is done during the register
step according to FW TLV.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New devices will have rate scaling algorithm running in the firmware.
With this feature, the driver's responsiblity is to provide an initial
configuration and to handle notifications regarding recent rates and
some other parameters. Debugfs hooks will be still available for
reading the current rate/statistics and setting a fixed rate.
The old API is supported so far, though both APIs cannot be used
simultaneously.
This is the first patch in the series. It adds a new TLV specifying
FW support for the new API and updates lq_sta to support two types
of rate scaling.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We might erroneously get to error dumping code when the
device is already stopped.
In that case the driver will detect a defective value and will try to
reset the HW, assuming it is only a bus issue. The driver than
proceeds with the dumping.
The result has two side effects:
1. The device won't be stopped again, since the transport status is
already stopped, so the device remains powered on while it actually
should be stopped.
2. The dump in that case is completely garbaged and useless.
Detect and avoid this. It will also make debugging such issues
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the removal of non-DQA code, we don't need the queues
variable any more. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the WFA vendor specific TPC report IE to probe requests
when it is not added by the FW. The FW will still need to set
the tx power field.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When RADA is active, the hardware decrypts the packets and strips off
the MIC as it is useless after decryption. Indicate that to mac80211.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the flag that indicates that ICV was stripped on if
this option was enabled in the HW.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before deleting a time event (remain-on-channel instance), flush
the queue so that frames cannot get stuck on it. We already flush
the AUX STA queues, but a separate station is used for the P2P
Device queue.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
add 1 PCI ID for 9260 series and 1 for 22000 series.
Cc: stable@vger.kernel.org
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
-----BEGIN PGP SIGNATURE-----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=j1dk
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi updates for v4.16
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
kvalo:
There were conflicts, I fixed them with taking into account commit c2c48ddfc8
("iwlwifi: fix firmware names for 9000 and A000 series hw"):
CONFLICT (content): Merge conflict in drivers/net/wireless/intel/iwlwifi/iwl-config.h
CONFLICT (modify/delete): drivers/net/wireless/intel/iwlwifi/cfg/a000.c deleted in ca495785063c428641cc6df8888afd2587ca6677 and modified in HEAD. Version HEAD of drivers/net/wireless/intel/iwlwifi/cfg/a000.c left in tree.
* One fix in rate-scaling;
* One fix for the TX queue hang detection for AP/GO modes;
* Fix the TX queue hang timeout used in monitor interfaces;
* Fix packet injection;
* Remove a wrong error message when dumping PCI registers;
* Fix race condition with RF-kill;
-----BEGIN PGP SIGNATURE-----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=eD7A
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Second batch of fixes intended for 4.15.
* One fix in rate-scaling;
* One fix for the TX queue hang detection for AP/GO modes;
* Fix the TX queue hang timeout used in monitor interfaces;
* Fix packet injection;
* Remove a wrong error message when dumping PCI registers;
* Fix race condition with RF-kill;
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since iwl_mvm_start_p2p_roc() is only called from iwl_mvm_roc(),
which already flushes the same work item, doing it again in it
is superfluous. Remove it and move the comment to the first one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ucode_major and ucode_minor were swapped. This has
no practical consequences since those fields are not used.
Same goes for umac_major and umac_minor which were only
printed under certain debug flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
Even if no ALIVE was received, the WRT data can still
be collected. Add this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Starting from a version 35, the minor version should be
printed in hexa.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This feature was actually removed from firmware, but without
ever telling the driver. Since nobody is actually using it,
just remove it entirely without bothering with a capability
check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API will not be used, remove the code that
supports it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we are in a search cycle, we try different combinations
of parameters. Those combinations are called 'columns'.
When we switch to a new column, we first need to check if
this column has a suitable rate, if not, we can't try it.
This means we must not erase the statistics we gathered
for the previous column until we are sure that we are
indeed switching column.
The code that tries to switch to a new column first sets
a whole bunch of things for the new column, and only then
checks that we can find suitable rates in that column.
While doing that, the code mistakenly erased the rate
statistics. This code was right until
struct iwl_scale_tbl_info grew up for TPC.
Fix this to make sure we don't erase the rate statistics
until we are sure that we can indeed switch to the new
column.
Note that this bug is really harmless since it causes a
change in the behavior only when we can't find any rate
in the new column which should really not happen. In the
case we do find a suitable we reset the rate statistics
a few lines later anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In A000 family, compressed BA notifs can include MGMT
frames, so don't fail RXs in such a case.
While at it, since in A000 the TID for MGMT frames is
15, treat it in the RX flow as if received TID 8. This
way we won't require special handling of this TID.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This bit will be used in CCK to indicate short preamble.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting HW rfkill we get stop_device being called from
two paths.
One path is the IRQ calling stop device, and updating op
mode and stack.
As a result, cfg80211 is running rfkill sync work that shuts
down all devices (second path).
In the second path, we eventually get to iwl_mvm_stop_device
which calls iwl_fw_dump_conf_clear->iwl_fw_dbg_stop_recording,
that access periphery registers.
The device may be stopped at this point from the first path,
which will result with a failure to access those registers.
Simply checking for the trans status is insufficient, since
the race will still exist, only minimized.
Instead, move the stop from iwl_fw_dump_conf_clear (which is
getting called only from stop path) to the transport stop
device function, where the access is always safe.
This has the added value, of actually stopping dbgc before
stopping device even when the stop is initiated from the
transport.
Fixes: 1efc3843a4 ("iwlwifi: stop dbgc recording before stopping DMA")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current pci dumping code code is always falling to the error
path, resulting with a constant "Read failed" message, also
for the successful reads.
Fixes: a5c932e41fdd ("iwlwifi: pcie: dump registers when HW becomes inaccessible")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.
Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MONITOR type is missing in the interface type switch.
Add it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we act as an AP, new firmware versions handle
internally the power saving clients and the driver doesn't
know that the peers went to sleep. It is, hence, possible
that a peer goes to sleep for a long time and stop pulling
frames. This will cause its transmit queue to hang which is
a condition that triggers the recovery flow in the driver.
While this client is certainly buggy (it should have pulled
the frame based on the TIM IE in the beacon), we can't blow
up because of a buggy client.
Change the current implementation to not enable the
transmit queue hang detection on queues that serve peers
when we act as an AP / GO.
We can still enable this mechanism using the debug
configuration which can come in handy when we want to
debug why the client doesn't wake up.
Cc: stable@vger.kernel.org # v4.13
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ieee80211_rx_status::chains was always set to zero.
That caused rate scaling to always start with the
lowest rate possible (rs_get_initial_rate).
Set it correctly according to the MPDU response.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
-----BEGIN PGP SIGNATURE-----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=JPn9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
iwlwifi: first set of fixes for 4.15
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
iwlwifi 9000 and a0000 series hw contains an extra dash in firmware
file name as seeen in modinfo output for kernel 4.14:
firmware: iwlwifi-9260-th-b0-jf-b0--34.ucode
firmware: iwlwifi-9260-th-a0-jf-a0--34.ucode
firmware: iwlwifi-9000-pu-a0-jf-b0--34.ucode
firmware: iwlwifi-9000-pu-a0-jf-a0--34.ucode
firmware: iwlwifi-QuQnj-a0-hr-a0--34.ucode
firmware: iwlwifi-QuQnj-a0-jf-b0--34.ucode
firmware: iwlwifi-QuQnj-f0-hr-a0--34.ucode
firmware: iwlwifi-Qu-a0-jf-b0--34.ucode
firmware: iwlwifi-Qu-a0-hr-a0--34.ucode
Fix that by dropping the extra adding of '"-"'.
Signed-off-by: Thomas Backlund <tmb@mageia.org>
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A lot of PCI IDs were missing and there were some problems with the
configuration and firmware selection for devices on the 9000 series.
Fix the firmware selection by adding files for the B-steps; add
configuration for some integrated devices; and add a bunch of PCI IDs
(mostly for integrated devices) that were missing from the driver's
list.
Without this patch, a lot of devices will not be recognized or will
try to load the wrong firmware file.
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Newer firmware versions (such as iwlwifi-8000C-34.ucode) have
introduced an API change in the SCAN_REQ_UMAC command that is not
backwards compatible. The driver needs to detect and use the new API
format when the firmware reports it, otherwise the scan command will
not work properly, causing a command timeout.
Fix this by adding a TLV that tells the driver that the new API is in
use and use the correct structures for it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=197591
Fixes: d7a5b3e9e4 ("iwlwifi: mvm: bump API to 34 for 8000 and up")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pointer sta_priv is assigned but never read, hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/wireless/intel/iwlegacy/4965-rs.c:2163:2: warning: Value
stored to 'sta_priv' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
-----BEGIN PGP SIGNATURE-----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=CC8e
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi updates
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a hardware restart the BA session data in HW is lost
so the reorder buffer simply passes the frames to mac80211 as is
as there is no NSSN set. Instead, we will drop these frames
before they reach the reorder buffer. mac80211 drops such frames anyway,
but we shouldn't rely on that. In addition it saves some
processing time
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
The RCU lifetime on baid_data is unclear, so this adds a direct copy of the
rcu_ptr passed to the original callback. It may be possible to improve this
to just use baid_data->mvm->baid_map[baid_data->baid] instead.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_flush_tx_path() function sends a synchronous command to
the firmware. When doing that, we must hold the mutex. The
iwl_mvm_flush_no_vif() function was mistakenly not holding the mutex.
Fix it.
Fixes: 6110d9e5bd ("iwlwifi: mvm: Flush non STA TX queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the mac flush flow, we should flush all existing queues.
Since FW API for a000 devices is flush per RA-TID, simply
flush all stations with all tids.
From FW perspective, asking to flush a TID that doesn't have
a queue is valid, so we can just set all bits in the TID mask.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is very indented and hard to read.
Refactor it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we return early from sync_rx_queues for a000 devices.
This may cause, in case of a non-empty reorder buffer, a warning
later on since the RX queue isn't getting the notification to
empty it.
A better approach would be to send the notification for the default
queue only.
Do this hard coded for now, until we will have the API to enable
multi queue for a000 devices.
Fixes: bc02946964 ("iwlwifi: mvm: disable RX queue notification for a000 devices")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit a6d24fad00 ("iwlwifi: pcie: dump registers when HW becomes
inaccessible") added a function to dump pcie config registers and
memory mapped registers on a failure. It is currently only accessible
within trans.c. Add it to struct iwl_trans_ops, so that failure cases
in other files can call it. While there, add a call to this function
from iwl_pcie_load_firmware_chunk in pcie/tx.c, since this is a common
failure case seen on some platforms.
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
[modified the commit message slightly]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This was used for internal devices that are now deprecated.
All the currently existing devices can do paging without
any help from the host.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We had a bunch of code that was relevant for internal
devices only. Those devices are now being depreceated.
Kill all the now unneeded code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When there is a reorder timeout, we may get to a situation
where we have the timeout latency for all the next 64 frames.
This happens since NSSN is behind for a while, and the driver
won't release the frames, since it is not allowed by NSSN.
As a result the frame is stored in the reorder buffer although
there is no hole, and released 100 ms later.
Add a direct comparison to the reorder buffer head, and release
immediately if possible.
For example:
Frame 0 is missed. We receive frame 1, and store it in the buffer.
After 100 ms, frame 1 is released and reorder buffer head is 2.
We then receive frame 2, with NSSN 0, and store it instead of
releasing it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't plan to have products with 3 antennas in the near
future. All the rest of the code follows the same
assumption as well.
Remove the support for antenna C from rs_toggle_ant.
When trying to toggle from ANT_B, this avoids to go through
ANT_C, discover that it doesn't exist and continue to ANT_A.
In MIMO, this avoids to do ANT_AB -> ANT_BC -> ANT_AC and
back to ANT_AB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After a FW reset on A000 NICs, the driver doesn't
set the seq number when re-allocating the queues.
This in turn leads to a mismatch between the seq
number the driver thinks each frame has, and the
actual seq num given by the HW.
This especially causes issues with aggregations,
since the driver could be waiting to start an
aggregation and queue traffic from the mac80211
until then, when actually it shouldn't be waiting.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the code is mixing defines and is inconsistent.
When enabling a queue, we usually configure the scheduler
with IWL_FRAME_LIMIT - 64.
When sending to firmware the rate scaling, we limit aggregation
to LINK_QUAL_AGG_FRAME_LIMIT_DEF - 63, due to a scheduler bug.
Given that, clean up the following:
- Fix a stray queue enablement with LINK_QUAL_AGG_FRAME_LIMIT_DEF.
- Change the comparison that tests if queue needs to be reconfigured
to be compared directly to how it was configured.
This also saves the redundant round down of the buffer size just
for the sake of comparing it, making the code more readable.
- Better document gen2 logic
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a macro for converting TX response rate to a
rate scale value, use it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This variable is never used, so remove the code to set it.
After this, the variable 'iph' also has the same fate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's hard to find values that are missing in the list, so sorting the
values and comparing them makes it much easier. To simplify this
task, sort the devices in the list.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the compressed BA notif, the driver didn't parse out
the LQ color, so statistics for the rates tried were
always thrown out. Add it so it gets correctly used.
While at it, fix the name of the relevant field in the
struct.
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now have two different minimum valid values for
umac_error_event_table. To avoid hardcoding the minimum value in the
driver, add a value to cfg where it can be read from.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in checking the validity of the
umac_error_event_table pointer every time we generate a dump. It's
cleaner to do so when we read the value, namely when we receive the
alive data.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, UMAC error data reading is restricted to DCCM.
A000 NICs use SMEM for this data.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All callers of iwl_mvm_release_frames() already have the baid_data
pointer, so we don't need to (re)calculate it inside the function.
Just pass it instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reason station id and tid fields are both in baid data and
in the reorder buffer per queue is that we couldn't access the
baid_data in the reorder timer functions.
Now that we do some pointer math and access it anyway, those
fields can be removed.
This save some space and some code.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we may have up to 256 entries per reorder buffer, and possibly up
to 16 queues, we can use a LOT of memory for this (64k for each station).
Allocate it according to what we need, which is of course much less for HT
stations (only 16k at a max of 16 queues).
However, this comes at the expense of complicating the code a bit to
calculate the right entry structure to use for each frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The default power limit read from the SPLC method in ACPI doesn't
have anything to do with the transport and is only used in the opmode,
so we can remove it from the trans. Additionally, this value is only
user when the opmode is starting, so we don't need to store it
anywhere.
Remove the dflt_pwr_limit element from the trans and move call to
iwl_acpi_get_pwr_limit() call to mvm.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the wrong statistics size is a problem, having a warning
will help us catch it quicker during firmware/driver development.
In released firmware/driver versions, we obviously make sure this
won't happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move most of the set_dflt_pwr_limit() function to acpi.c and make it
return the pwr_limit value instead of setting directly. Also rename
it to iwl_acpi_get_pwr_limit().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the double indentation in the configuration structs
for a000 family devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_get_bios_mcc() function was in the iwl-nvm-parse.c file, but
it has nothing to do with the NVM. Move it to fw/acpi.c and rename it
to iwl_acpi_get_mcc().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The way iwl_get_bios_mcc() gets the WiFi package and checks for its
integrity is almost identical to the new iwl_acpi_get_wifi_pkg()
function. Instead of having duplicate code, convert it to use the
common code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of finding the wifi package with its own code, we can reuse
the new iwl_acpi_get_wifi_pkg() function when reading the default
power limit from SPLC.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move this function to acpi.c, renaming it to iwl_acpi_get_wifi_pkg(),
because it can also be used with other methods (i.e. SPLC and WRDD).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ACPI table size definitions were spread around the different files
that used them. Move them all to a common place.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of defining each method where they are used and re-defining
WIFI_DOMAIN in each one of them, move all the definitions to a central
place and define the domain only a single time.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are many places where the same process of invoking a method from
ACPI is used, causing a lot of duplicate code. To improve this,
introduce a new function to get an ACPI object by invoking an ACPI
method that can be reused.
Additionally, since this function needs to be called when we only have
the trans, the opmode or the device, introduce a new debug macro that
gets the device as a parameter so it can be used in the new function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there is a FW bug where the BAID value in the
metadata is not properly initialized we hit the warning for
every RX packet.
Change it to warn once and add elaborate message.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We conclude the HW became inaccessible when we timeout waiting for
a bit to be set in a memory mapped register (CSR_GP_CNTRL). This
conclusion may not be true because the bit may not get set due to:
- a firmware issue
- a driver issue
- a PCI bus issue
- a platform issue
There are a lot of such reports with really no good debug information
beyond this message to help us.
Add some debug information and attempt to dump the different register
spaces at such a failure:
* Dump some configuration space of device - this will tell us if
something very basic is broken in the PCIe bus (so that configuration
accesses are failing). If this works, the PCIe bus seems OK. If this
does not work, it is definitely an PCIe issue.
* Dump some memory mapped registers - if we're reading some sane'ish
values, this will tell us that the PCIe bus is OK, but may be a firmware
/ driver issue. If this does not work, it may be a PCI configuration
issue or a driver/firmware issue.
* Dump parent and device's AER registers, will give us some straws to
chew on.
This is the sample output:
[ 13.082651] ------------[ cut here ]------------
[ 13.086791] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
[ 13.086793] iwlwifi 0000:01:00.0: iwlwifi device config registers:
[ 13.086893] iwlwifi 0000:01:00.0: 00000000: 095a8086 00100406 02800059 00000000 00000004 00000000 00000000 00000000
[ 13.086895] iwlwifi 0000:01:00.0: 00000020: 00000000 00000000 00000000 50108086 00000000 000000c8 00000000 00000100
[ 13.086901] iwlwifi 0000:01:00.0: iwlwifi device memory mapped registers:
[ 13.086989] iwlwifi 0000:01:00.0: 00000000: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086991] iwlwifi 0000:01:00.0: 00000020: ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
[ 13.086999] iwlwifi 0000:01:00.0: iwlwifi device AER capability structure:
[ 13.087033] iwlwifi 0000:01:00.0: 00000000: 14010001 00100000 00000000 00462031 00002000 00002000 00000014 40000001
[ 13.087034] iwlwifi 0000:01:00.0: 00000020: 0000000f d140000c 00000000
[ 13.087036] iwlwifi 0000:01:00.0: iwlwifi parent port (0000:00:1c.0) config registers:
[ 13.087074] iwlwifi 0000:00:1c.0: 00000000: 9d108086 00100506 060400f1 00810010 00000000 00000000 00010100 200000f0
[ 13.087075] iwlwifi 0000:00:1c.0: 00000020: d140d140 0001fff1 00000000 00000000 00000000 00000040 00000000 0006010b
[ 13.087087] ------------[ cut here ]------------
[ 13.087095] WARNING: CPU: 0 PID: 1759 at drivers/net/wireless/iwl7000/iwlwifi/pcie/trans.c:2082 iwl_trans_pcie_reclaim+0x1ee4/0x2b9a [iwlwifi]()
[ 13.087096] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes three trivial issues as reported by checkpatch.pl, namely two
switch/case indentation issues and one alignment issue in a multiline
comment.
Signed-off-by: Christoph Böhmwalder <christoph@boehmwalder.at>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This helps for documentation and clarifies the code by defining the
exact response struct for the marker command.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These enum values don't exist, so remove their documentation as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have an AP which supports HT and a single HT
station is connected, we change the min_width from
NL80211_CHAN_WIDTH_20_NOHT to NL80211_CHAN_WIDTH_20. This
of course has no implication on the channel width but still
sends a command to the firmware.
Remember the last width that was sent and refrain from
sending unnecessary commands to the firmware.
Sending a PHY_CTXT_CMD to the firmware has a cost since it
recalculates the presence on the medium and because of that
it closes the transmit queues for a short while.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver reads xtal_calib from NVM file, but actually never uses it.
This is only used in dvm driver.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Devices in the A000 family can use a different size for the command queue.
To allow this, make the command queue size configurable and set the size
for A000 devices to 32.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This would enable to better catch timing issues with
cases that WRT dump takes too much time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger that collects data when a frame is released
because of the timer of the reordering buffer was not
implemented for 9000 devices.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This was never used by any product. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New quota command adds a field indicating low latency
direction per quota.
A TLV API bit was added to indicate the new API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new a000 device with PCI ID (0x2720, 0x0030).
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCI ID (0x2720, 0x0070) was set with the config struct
iwla000_2ax_cfg_hr instead of iwla000_2ac_cfg_hr_cdb.
Fixes: 175b87c692 ("iwlwifi: add the new a000_2ax series")
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
De-inline iwl_trans_ref/unref and move it to common transport code
in preparation for more common code to come to these functions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a dbgfs entry for an easy way during runtime to
check what FW file was loaded, and get some general
FW-related data.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver currently handles two NVM formats,
one for 7000 family and below, and one for 8000 family and above.
The 3168 series uses something in between,
so currently the driver uses incorrect offsets for it.
Fix the incorrect offsets.
Fixes: c4836b056d ("iwlwifi: Add PCI IDs for the new 3168 series")
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The current channel flags printing is very strange and messy,
in LAR we sometimes print the channel number and sometimes the
frequency, in both we print a calculated value (whether ad-hoc
is supported or not) etc.
Unify all this to
* print the channel number, not the frequency
* remove the band print (2.4/5.2 GHz, it's obvious)
* remove the calculated Ad-Hoc print
Doing all of this also gets the length of the string to a max
of 101 characters, which is below the max of 110 for tracing,
and thus avoids the warning that came up on certain channels
with certain flag combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It seems that libsensors treats -EIO as a special non-recoverable
failure when it tries to read the temperature while the firmware is
not running. To solve that, change the error code to a milder
-ENODATA.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196941
Fixes: c221daf219 ("iwlwifi: mvm: add registration to thermal zone")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today we stop the device and the DMA without stopping the dbgc
recording before. This causes host crashes when the DMA
rate is high.
Stop dbgc recording when clearing the fw debug configuration
to fix this.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In monitor mode we are not expected to decrypt encrypted
packets (not having the keys).
Hence we are expected to get an unknown rx security status.
Keeping the print in monitor mode causes a print for each
captured packet flooding the dmesg.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't populate const array ac_to_fifo on the stack in an inlined
function, instead make it static. Makes the object code smaller
by over 800 bytes:
text data bss dec hex filename
159029 33154 1216 193399 2f377 4965-mac.o
text data bss dec hex filename
158122 33250 1216 192588 2f04c 4965-mac.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The condition to check if reorder buffer ran out of
space is faulty, as it takes into account only the
NSSN.
In case the head SN was too far behind the reorder
buffer should move forward, regardless of the NSSN
status.
This caused the driver to release packets out of order
in some scenarios.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always must set the status to what we consider success before
calling iwl_mvm_send_cmd_status() (also iwl_mvm_send_cmd_pdu_status()
which calls it). Fix a few places where initialization is missing.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always need to initialize the status argument to the success case
before calling iwl_mvm_send_cmd_status() or
iwl_mvm_send_cmd_pdu_status() (which calls the former) otherwise we
may get an uninitialized value back. In this case, we use
ADD_STA_SUCCESS as success.
Fixes: 732d06e9d9 ("iwlwifi: mvm: add station before allocating a queue")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were ignoring the FIF_ALLMULTI flag when setting the multicast
addresses with MCAST_FILTER_CMD. Check if this flag is set and enable
pass_all accordingly. We also need to set the count to 0 if pass_all
is enable so we don't pass addresses to the firmware when not needed
(as doing so causes an assert).
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196741
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MCAST_FILTER_CMD can get quite large when we have many mcast
addresses to set (we support up to 255). So the command should be
send as NOCOPY to prevent a warning caused by too-long commands:
WARNING: CPU: 0 PID: 9700 at /root/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/pcie/tx.c:1550 iwl_pcie_enqueue_hcmd+0x8c7/0xb40 [iwlwifi]
Command MCAST_FILTER_CMD (0x1d0) is too large (328 bytes)
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196743
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_start_mac_queues() takes a bitmap of the queues to wake.
When deferred tx is purged, set the bit of the hw_queue so
the correct queue will be waken up.
Fixes: 7e39a00d59 ("iwlwifi: mvm: start mac queues when deferred tx frames are purged")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new state to enum iwl_mvm_agg_state, which is used between
queueing the work that starts tx aggregations and actually starting that
work (changing to state IWL_AGG_STARTING).
This solves a race where ieee80211_start_tx_ba_session is called a
second time, before the work queued by the first run has a chance to
change the agg_state. In this case the second call to
ieee80211_start_tx_ba_session returns an error, and the fallback is to
abort the ba session start.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AP interfaces now send all non-bufferable frames using the broadcast
station. Thus allow them to use the probe queue and don't warn about
it.
Fixes: eb045e6e03 ("iwlwifi: mvm: Avoid deferring non bufferable frames")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting wowlan mac80211 requests flush w/o vif
and we ignore this request. As a result some packets
stay stuck in the queue and it may end up with a queue
hang.
Allow the driver to flush queues even if station isn't
specified.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we set disconnect on wowlan and run suspend/resume, will run
into:
...snipped
iwlwifi 0000:01:00.0: Failed to load firmware chunk!
iwlwifi 0000:01:00.0: Could not load the [0] uCode section
iwlwifi 0000:01:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
It is because we still keep IWL_MVM_STATUS_IN_HW_RESTART in
__iwl_mvm_resume. When mac80211 starts the device as
__iwl_mvm_mac_start(), we will miss iwl_mvm_restart_cleanup(mvm).
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The LEDS_CMD command is only supported in some newer FW versions
(e.g. iwlwifi-8000C-31.ucode), so we can't send it to older versions
(such as iwlwifi-8000C-27.ucode).
To fix this, check for a new bit in the FW capabilities TLV that tells
when the command is supported.
Note that the current version of -31.ucode in linux-firmware.git
(31.532993.0) does not have this capability bit set, so the LED won't
work, even though this version should support it. But we will update
this firmware soon, so it won't be a problem anymore.
Fixes: 7089ae634c ("iwlwifi: mvm: use firmware LED command where applicable")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These devices support -34.ucode, so load it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use bcast station for all non bufferable frames on AP and AD-HOC.
The host is no longer aware of STAs PS status because of buffer
station offload, so we can't rely on mac80211 to toggle on
IEEE80211_TX_CTL_NO_PS_BUFFER bit.
A possible issue with buffering such frames, beside the obvious spec
violation, is when a station disconnects while in PS but the AP isn't
aware of that. In such scenarios the AP won't be able to send probe
responses or auth frames so the STA won't be able to reconnect and
the AP will have a queue hang.
Fixes: 3e56eadfb6 ("iwlwifi: mvm: implement AP/GO uAPSD support")
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a debug print that sometimes reaches over
110 chars, thus generating a warning in those cases.
Split the print into two to prevent these cases.
Fixes: 92b0f7b26b ("iwlwifi: split the regulatory rules when the bandwidth flags require it")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Work queues cannot be allocated when a mutex is held because the mutex
may be in use and that would make it sleep. Doing so generates the
following splat with 4.13+:
[ 19.513298] ======================================================
[ 19.513429] WARNING: possible circular locking dependency detected
[ 19.513557] 4.13.0-rc5+ #6 Not tainted
[ 19.513638] ------------------------------------------------------
[ 19.513767] cpuhp/0/12 is trying to acquire lock:
[ 19.513867] (&tz->lock){+.+.+.}, at: [<ffffffff924afebb>] thermal_zone_get_temp+0x5b/0xb0
[ 19.514047]
[ 19.514047] but task is already holding lock:
[ 19.514166] (cpuhp_state){+.+.+.}, at: [<ffffffff91cc4baa>] cpuhp_thread_fun+0x3a/0x210
[ 19.514338]
[ 19.514338] which lock already depends on the new lock.
This lock dependency already existed with previous kernel versions,
but it was not detected until commit 49dfe2a677 ("cpuhotplug: Link
lock stacks for hotplug callbacks") was introduced.
Reported-by: David Weinehall <david.weinehall@intel.com>
Reported-by: Jiri Kosina <jikos@kernel.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stephen Rothwell reported quite a few conflicts in iwlwifi between
wireless-drivers and wireless-drivers-next. To avoid any problems later in
other trees merge w-d to w-d-next to fix those conflicts early.
Make these const as they are only stored in the const field of a
net_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unlike the other sections of the NVM, the hw section is in big-endian.
To read a value from it, we had to cast it to __be16. Fix that by
using __be16 * for the entire section.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
At this point we have already copied the cfg pointer to mvm and we
have been dereferencing this pointer many times before, so it will
never be NULL or we would have crashed. Remove the useless check.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We always call iwl_nvm_init() with read_nvm_from_nic == true, so this
argument is useless. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We read the regulatory.lar_enabled field in iwl_fw_get_nvm() and store
it in nvm->lar_enabled, taking care of endianness. But then later we
read it again to pass the value to iwl_init_sbands() without handling
endianness. To solve this, simply reuse nvm->lar_enabled when calling
that function.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The OTP in some SKUs have erroneously allowed 40MHz and 80MHz channels
in the 5.2GHz band. The firmware has been modified to not allow this
in those SKUs, so the driver needs to do the same otherwise the
firmware will assert when we try to use it.
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tx BA session should be started according to the current throughput
without any dependence on the internal rate scaling state. The criteria
for opening a BA session will be 10 frames per second.
Sending frequent del BAs can cause inter-op issues with some APs. We'll
not close a BA session until we receive an explicit del BA from the
peer.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some new flags in the channel flags that we don't know
about. Also, the "WIDE" flag is very confusing, because it actually
means 20MHz bandwidth, which is not very wide.
Add the new flags and rename the confusing one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer versions of A000 devices come with two diffenent RF modules.
The PCI_ID, the subsystem ID and the RF ID are identical in these two cases,
so we need to differentiate them by using the CSR_HW_RF_ID register-
in order to load the appropriate firmware.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code did not consider the case that the channel switch counter
is <= 1, which would result with an inaccurate calculation of the
time event apply time.
As the specification states that in case of counter == 0 the switch
occurs at any time after the reception the frame, and for counter == 1
the switch would happens before the next TBTT, schedule the time
event immediately.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These messages are not reporting a real error, just the fact that the
firmware knows about more flags than the driver.
Currently these messages are presented to the user during boot if there
is no bootsplash covering the console, even when booting the kernel with
"quiet".
Demoting it to the warn level helps having a clean boot process.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the BT_MBOX_PRINT() macro from mvm/debugfs.c to fw/api/coex.h so
it can be reused and remove duplicate definition of BT_MBOX_MSG(),
keeping only the one already in coex.h.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we flush a queue, the packets will have a 'failed'
status but we shouldn't send a BAR. This check was missing.
Because of that, when we got an ampdu_action with
IEEE80211_AMPDU_TX_STOP_FLUSH, we started the following
ping pong with the firmware:
1) Set the station as 'draining'
2) Get a failed Tx status (DRAINED)
3) Send a BAR because of the failed Tx status
(loop of 2 and 3)
This loop wasn't endless since the BAR isn't sent on a
queue that would trigger a "nested" BAR.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a time event is already scheduled when trying to schedule one for
channel switch, the code assumes the channel switch is already
scheduled and no further action is required.
However, it is possible that the scheduled time event is actually
for session protection (e.g. when the first beacon after association
contains the CSA IE). In this case the channel switch will not be
scheduled which will finally lead to disconnection.
Fix this by removing the old time event and schduling a new one for
the channel switch.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware team is now re-using a bit that hasn't been
used for a few generations. Re-use for TX_ON_AIR drop.
This bit will be set by the firmware to indicate that
a frame in an A-MPDU was dropped but not because of the
already mapped reasons.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We use mvmsta for the sta->drv_priv in mvm, but in rs.c we have a
bunch of instances using sta_priv, which is probably due to it being
copied from dvm. Change all occurrences to mvmsta for consistency
with the rest of the driver
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have some of the SAR dummy functions when ACPI is not set declared
in mvm.h and some declared in fw.c. Group them all together in fw.c
for consistency and to avoid static/non-static issues.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a valid baid in a received frame, we need to
check that we are aware of this baid. If not, we check
that the OLD_SN bit set. If that's not the case, we issue
a WARNING. Print more data when that happens.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This name was missing in the list.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows to modify TFD_TX_CMD_SLOTS to a power of 2
which is smaller than 256.
Note that we still need to set values to wrap at 256
into the scheduler's write pointer, but all the rest of
the code can use shorter transmit queues.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware now adds more information about time sharing
with the Bluetooth core.
Adapt the API structures and add the new fields in the
debugfs hooks.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_wait_notification() function removes the wait entry from the
list. To make it clearer that it's doing the same thing as
iwl_remove_notification(), call the latter instead of having duplicate
code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to differentiate an INIT that ended early because of
RFKILL from one that succeded. Additionally, if INIT fails later,
during calibration, due to RFKILL, we can just return success and
continue as if we were already in RFKILL to start with.
Remove this unnecessary differentiation and do some other small
clean-ups while at it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The corunning block was supposed to help in coex scenarios.
It required the driver to configure the firmware based on
the coupling between the two antennas of the devices.
This was never in use and the configuration sent by the
driver has always been blank.
Remove all that code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware API defined in the header files didn't match
the structure that are actually passed by the firmware.
The impact could be a decision for MIMO in Tx or Rx in
coex scenarios.
Fixes: 430a3bbafd ("iwlwifi: mvm: BT Coex - new API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we unmap a non-empty Tx queue, we need to free the
pages that we allocated for the headers in TSO flows.
This code existed for the 9000 device family, but somehow
it got left out when the new Tx path for the A000 devices
was written.
Fixes: 2b0c5946d9ed ("iwlwifi: pcie: introduce a000 TX queues management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi. These references were inherited from a previous
project and are irrelevant here. Additionally, remove some irrelevant
references to 5100 HW. Remove all these.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Although nmi was triggered fine till now, it appears
that the driver didn't write the exact correct values
to the correct addresses for each HW.
Fix the nmi triggering by setting the correct addresses
and values.
Fixes: 4c9706dc2f ("iwlwifi: update nmi register")
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TVQM tells us the initial write pointer for a queue,
but that write pointer is in WiFi sequence number unit
and not in TFD index unit. Which means that the write
pointer in the TVQM's response can be bigger than the
Tx queue ring size.
Fix that by modulo'ing the write pointer from the TVQM
with the Tx queue size.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the queue config params is the associated station id.
Hence the FW must know about the station prior to the queue allocation.
In a000 devices, allocating a queue without a valid station
results with assert 0x2B00.
In FW restart flow the queues are allocated before
adding the station so first add the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix this issue if it is not supported by the firmware.
Fixes: 00f481bd89 ("iwlwifi: mvm: add ctdp operations to debugfs")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support a new version of the beacon template command. This replaces v8
of the command, which was missing the rate code. Also, export rate
decision logic to a separate function.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When an RX block-ack session times out, the firmware, which offloads
RX reordering but not the BA session negotiation, stops the session
but doesn't send a DELBA. This causes the the session to remain
active in the remote device, so no more BA sessions will be
established, causing a severe throughput degradation due to the lack
of aggregation.
Use the new ieee80211_rx_ba_timer_expired API when the ba session timer
expires, since this will tear down the ba session and also send a delba.
The previous API used is intended for drivers that offload the
addba/delba negotiation, but not the rx reordering, while our driver
does the opposite.
This patch depends on "mac80211: add api to start ba session timer
expired flow".
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there is no value received from BIOS
for cTDP budget, the default should be 2000 mWatt.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the NVM data in a000 devices should be shared
across operation mode.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the smem configuration to the fw data dump, once
the firmware crashes. This is useful mainly for later
parsing of the smem.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the defines has a wrong value.
Fixes: 1afb0ae421 ("iwlwifi: allow combining different phy images with mac images")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Load FW according to NIC type,
taking into account simulation, if exists.
This is determined by a prph register.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are a few places where we don't have a space between the * and
the @ in the parameter description. Also, in one case, the @ had
trailing space before the parameter name.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change iwl_set_ucode_api_flags(), iwl_set_ucode_capabilities() to be void.
No need to check returned values.
Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CT-kill is a thermal-based "RF-kill", which disables the NIC
completely if the temperature gets too high, in order to avoid damage.
Add a debugfs entry to simulate high temperatures, in order to test
CT-kill flows in the driver without having to physically heat the
device up.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.
Fixes: 503ab8c56c ("iwlwifi: Add 8000 HW family support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the module parameter is set to disable the LED, we leave the
initialization routine before setting the LEDS_INIT_COMPLETE
status bit. Therefore, there's no need to check the parameter
again on exit, just the status check is sufficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we start an Rx A-MPDU session, we first get the AddBA
request, then we send an ADD_STA command to the firmware
that will reply with a BAID which is a hardware resource
that tracks the BA session.
This BAID will appear on each and every frame that we get
from the firwmare until the A-MPDU session is torn down.
In the Rx path, we look at this BAID to manage the
reordering buffer.
This flow is inherently racy since the hardware will start
to put the BAID in the frames it receives even if the
firmware hasn't sent the response to the ADD_STA command.
This basically means that the driver can get frames with
a valid BAID that it doesn't know yet.
When that happens, the driver used to WARN.
Fix this by simply not WARN in this case. When the driver
will know abou the BAID, it will initialise the relevant
states and the next frame with a valid BAID will refresh
them.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AP mode, if a station is removed just as it is adding a new stream,
the queue in question will remain stopped and no more TX will happen
in this queue, leading to connection failures and other problems.
This is because under DQA, when tx is deferred because a queue needs
to be allocated, the mac queue for that TID is stopped until the new
stream is added. If at this point the station that this stream
belongs to is removed, all the deferred tx frames are purged, but the
mac queue is not restarted. As a result, all following tx on this
queue will not be transmitted.
Fix this by starting the relevant mac queues when the deferred tx
frames are purged.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiHuQAAoJEG4XJFUm622bVSEIAKdausycC6OOZjwTGWnFyxE/
58n79VTrTbXVLwJ7lSBCGYCTujc7amPxAVlDOLYd+9TKm0fO7gap50Gdl35HO5sp
9v/augHQSouz52q2vgsTi0JbXsqhJQZ4Ie4P0fo8OyqJMYAvFga2FhFBpJseMYd9
NX88SMoxAGgDkTC0JfzzLnA/jZ0W6ULai6zmRE1s6lUIynP2kzHgpfbMH3+KEkod
SUW+yX91MdOkkyFGXyY11uuBqanUpEVSAQXW6J76vw3qS88qIqaL3iIeJ6C4Vozq
fKNkHN4iZOd9FlKY1IFi4vS0+7hWiq6DQ3c+ngtU6cuq1XdBa6PuanC3I2e0B8E=
=PKUU
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should free 'wgds.pointer' here as done a few lines above in another
error handling path.
It was allocated within 'acpi_evaluate_object()'.
Fixes: c52030a01ccc ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_add_bcast_sta() and the iwl_mvm_rm_bcast_sta() functions
are only called in P2P flows. Add _p2p_ to the function names to make
this explicit.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to spell out the cases when we can just
use ieee80211_is_bufferable_mmpdu().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the TXQ timer freeze code will not properly handle the
large TVQM queue numbers, warn if we get into that code when
we have TVQM. Also, just to catch this earlier, warn if the
firmware image doesn't support AP_LINK_PS but we're running
on HW using TVQM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename this function to the more appropriate iwl_pcie_check_hw_rf_kill()
since it's only a function in the pcie code and cannot be called from
any other place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing purposes, we may want to disable EBS scans at compile time.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During init, the FW checks whether the FSEQ value matches what it
expects. If it doesn't match, we print a warning to let integrators
clearly know that something is wrong. This can happen if another core
(i.e. not WiFi) has updated the FSEQ version. This notification is
only sent by the FW in production, for development firmwares, an
assertion is triggered instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
If the OTP is empty, the NVM_GET_INFO command returns
with flags' bit(0) on. This means the FW returns the
default values for working with. This is allowed, so
use this returned data.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return status check of iwl_pcie_gen2_build_amsdu
was buggy. Fix it.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While waiting for queues to empty,
If txq_id == IWL_MVM_INVALID_QUEUE for all txq_ids,
ret is used uninitialized.
Found by Klocwork.
Fixes: d6d517b773 ("iwlwifi: add wait for tx queue empty")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FIFO numbering is different in A000 devices. This
means that we routed BE packets to BK FIFO. Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently support 3 different versions of the beacon template
command and the code does some tricks in order to reuse what is
possible across these versions. But it is a bit complicated to read
and soon there will be one more variation that the driver needs
implement, which would complicate it even further.
Refactor the way we send beacon template commands, which increases the
code size a bit, but makes it much easier to read.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Those constants have been unused for quite some time now.
Signed-off-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Convention has it to byte-swap the constant instead of the variable
when doing bit checks. This also generates better code when the swap
is actually needed, since the constant can be swapped at compile-time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two workarounds because RSS is currently broken on A000
devices due to firmware issues, but checking for the new TX API
doesn't really make sense. Check the hardware family instead of
the new TX API - there's nothing better to check since it's just
a temporary workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This may need to be refined later, but for now using this,
even with the TODO, is better than checking "has new TX API".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the shared memory command parsing into common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add two PCI IDs for the 9160 series.
Add five PCI IDs for the 9260 series.
Add one PCI IDs for the 9270 series.
Add seven PCI IDs for the 9460 series.
Add five PCI IDs for the 9560 series.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the STA_FLG_RTS_MIMO_PROT bit in station_flags_msk of the add sta
command, so that when smps mode changes, the FW will know about it.
In particular, in AP mode, clients are added upon receival of an auth
request, at which point there's no knowledge of the client's smps mode.
When the assoc request arrives, the add_sta command is resent to modify
the station parameters. At this point the driver knows the smps mode,
but since the corresponding bit in the mask is not set, the fw doesn't
update this field so there's no rts protection for mimo.
Fixes: 5bc5aaad40 ("iwlwifi: mvm: set up initial SMPS/NSS station info")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
C step NICs should use the latest FW (currently B step).
Correct the condition to make C step NICs advanced its default FW name
to the latest one.
Also rename _next_ to b_or_c to avoid confusion.
Fixes: 5da083d192 ("iwlwifi: add support for 9000 HW B-step NICs")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Statistics should be collected according to the actual rate a
frame/aggregation was transmitted and not according to the initial rate
from the last LQ command (these rates are different if the frames were
retransmitted at a lower rate from the rate scale table).
This is needed to remove throughput degradation.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.
This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we create a regulatory domain out of an MCC
notification, we need to make sure that all the channels
in the rule have the exact same properties.
The current code mixes channel 36 and 40 although 36 can be
a control channel with HT40+ (36, 40) whereas 40 can't be
a control channel with HT40+ since (40, 44) is invalid.
Because of that, cfg80211 would allow to connect in 40MHz
to APs that are configured to channel 40 HT40+ and that made
our firmware assert.
Fix this by checking the bandwidth flags before taking the
decision if the rule should be split.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299 partly.
Fixes: af45a9003f ("iwlwifi: create regdomain from mcc_update_cmd response")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware now adds a new DWORD for the MLME offload's
capability even on firmware versions that don't support
it.
Add the TLV bit to avoid getting the print:
capa flags index 3 larger than supported by driver.
This fixes the bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=196195
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.
On A000 devices series, the IV is always added by the
device.
Fix this.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Causes the PCI stack to complain, and then eventually call the
PCI remove function, which ipw2100 is not expecting. It then
tries to unregister an already-released netdev and other nasty
things, leading to a panic.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1185518
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A hardware/firmware error may happen at any point in time. In
particular, it might happen while mac80211 is in the middle of
a flow. We observed the following situation:
* mac80211 is in authentication flow, in ieee80211_prep_connection()
* iwlwifi firmware crashes, but no error can be reported at this
precise point (mostly because the driver method is void, but even
if it wasn't we'd just shift to a race condition)
* mac80211 continues the flow, trying to add the AP station
* iwlwifi has already set its internal restart flag, and so thinks
that adding the station is part of the restart and already set up,
so it uses the information that's supposed to already be in the
struct
This can happen with any flow in mac80211 and with any information
we try to preserve across hardware restarts.
To fix this, only set a new HW_RESTART_REQUESTED flag and translate
that to IN_HW_RESTART once mac80211 actually starts the restart by
calling our start() method. As a consequence, any mac80211 flow in
progress at the time of the restart will properly finish (certainly
with errors), before the restart is attempted.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195299.
Reported-by: djagoo <dev@djagoo.io>
Reported-by: Łukasz Siudut <lsiudut@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When IBSS was implemented for DQA, we missid a few places where it
should be handled in the same way as AP.
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_trace_data is somewhat confusing. It returns a bool
that tells if the payload of the skb should be added to
the tx_data event. If it returns false, then the payload
of the skb is added to the tx event.
The purpose is to be able to start tracing with
-e iwlwifi
and record non-data packets only which saves bandwidth.
Since EAPOLs are important, seldom and not real data
packet (despite being WiFi data packets), they are
included in tx event and thus iwl_trace_data returns false
on those. This last part was buggy, and because of that,
all the data packets were included in the tx event.
Fix that.
Fixes: 0c4cb7314d ("iwlwifi: tracing: decouple from mac80211")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't set the error code here so we end up returning ERR_PTR(0) which
is NULL. The caller doesn't expect that so it results in a NULL
dereference.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes, we can have an firmware crash while trying to
recover from a previous firmware problem.
When that happens, lots of things can go wrong. For example
the stations don't get added properly to mvm->fw_id_to_mac_id.
Mac80211 tries to stop A-MPDU upon reconfig but in case of
a firmware crash we will bail out fairly early and in the
end, we won't delete the A-MPDU Rx timeout.
When that timer expired after a double firmware crash,
we end up dereferencing mvm->fw_id_to_mac_id[sta_id]
which is NULL.
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before TVQM, all TX queues were allocated straight at init.
With TVQM, queues are allocated on demand and hence we need
to check if a queue exists before dereferencing it.
Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlagn_check_ratid_empty takes the tid as a parameter, but
it doesn't check that it is not IWL_TID_NON_QOS.
Since IWL_TID_NON_QOS = 8 and iwl_priv::tid_data is an array
with 8 entries, accessing iwl_priv::tid_data[IWL_TID_NON_QOS]
is a bad idea.
This happened in iwlagn_rx_reply_tx. Since
iwlagn_check_ratid_empty is relevant only to check whether
we can open A-MPDU, this flow is irrelevant if tid is
IWL_TID_NON_QOS. Call iwlagn_check_ratid_empty only inside
the
if (tid != IWL_TID_NON_QOS)
a few lines earlier in the function.
Cc: <stable@vger.kernel.org>
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work
with const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpX4A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymobgCfd0d13IfpZoq1N41wc6z2Z0xD7cwAnRMeH1/p
kEeISGpHPYP9f8PBh9FO
=Hfqt
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big driver core update for 4.13-rc1.
The large majority of this is a lot of cleanup of old fields in the
driver core structures and their remaining usages in random drivers.
All of those fixes have been reviewed by the various subsystem
maintainers. There's also some small firmware updates in here, a new
kobject uevent api interface that makes userspace interaction easier,
and a few other minor things.
All of these have been in linux-next for a long while with no reported
issues"
* tag 'driver-core-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (56 commits)
arm: mach-rpc: ecard: fix build error
zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()
driver-core: remove struct bus_type.dev_attrs
powerpc: vio_cmo: use dev_groups and not dev_attrs for bus_type
powerpc: vio: use dev_groups and not dev_attrs for bus_type
USB: usbip: convert to use DRIVER_ATTR_RW
s390: drivers: convert to use DRIVER_ATTR_RO/WO
platform: thinkpad_acpi: convert to use DRIVER_ATTR_RO/RW
pcmcia: ds: convert to use DRIVER_ATTR_RO
wireless: ipw2x00: convert to use DRIVER_ATTR_RW
net: ehea: convert to use DRIVER_ATTR_RO
net: caif: convert to use DRIVER_ATTR_RO
TTY: hvc: convert to use DRIVER_ATTR_RW
PCI: pci-driver: convert to use DRIVER_ATTR_WO
IB: nes: convert to use DRIVER_ATTR_RW
HID: hid-core: convert to use DRIVER_ATTR_RO and drv_groups
arm: ecard: fix dev_groups patch typo
tty: serdev: use dev_groups and not dev_attrs for bus_type
sparc: vio: use dev_groups and not dev_attrs for bus_type
hid: intel-ish-hid: use dev_groups and not dev_attrs for bus_type
...
The newest devices need a longer time to reset because of
their more complex hardware. Wait 5ms after device reset.
Consolidate all the places that reset the device in the
PCIe transport to avoid future bugs.
While at it, unify the flow to use set_bit instead of full
write as requested by the hardware designers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_pcie_apm_init can fail so make sure that the caller
takes the status into account.
Also, ensure that the error that iwl_pcie_apm_init can emit
will appear in the kernel log by default.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
* mac80211 sends auth
* we stop mac80211 queues to allocate a hw queue
* authentication is aborted
* we allocate HW queue and start mac80211 queues
* mac80211 removes station
* mac80211 hands us the auth frame from the pending queue
At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.
In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.
However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.
Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When going into suspend, the HW configuration for MSI-X will
likely be lost. As a consequence, after waking up, all IRQ
causes will be mapped to interrupt 0, and as a consequence we
don't notice the interrupt because in most cases this is an
interrupt for a queue, and getting it doesn't read the other
cause registers.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.
Fixes: bb81bb68f4 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When in non-DQA mode, mac80211 actually gets a pretty much perfect
idea (in vif->hw_queue/cab_queue) of which queues we're using. But
in DQA mode, this isn't true - nonetheless, we were adding all the
queues, even the ones stations are using, to the queue allocation
bitmap.
Fix this, we should only add the queues we really are using in DQA
mode:
* IWL_MVM_OFFCHANNEL_QUEUE, as we use this in both modes
* mvm->aux_queue, as we use this in both modes - mac80211
never really knows about it but we use it as a cookie
internally, so can't reuse it
* possibly the GCAST queue (cab_queue)
* all the "queues" we told mac80211 about we were using on each
interface (vif->hw_queue), these are entirely virtual in this
mode
Also add back the failure now when we can't allocate any more of
these - now virtual - queues; this was skipped in DQA mode and
would lead to having multiple ACs or even interfaces use the same
queue number in mac80211 (10, since that's the limit), which would
stop far too many queues if stopped.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the driver, we track which hardware queue is associated with
which mac80211 "hw_queue", in order to be able to stop and wake
it. When moving these bitmaps out of the queue_info structures,
the type of the bitmap was erroneously changed from u32 to u8,
presumably in order to save memory.
Turns out that u32 isn't needed, because the highest queue we
can ever tell mac80211 is always < 16, but a u16 definitely is
needed, queues >=8 do happen.
While at it, throw a BUILD_BUG_ON() into the place where we set
the limit (mvm->first_agg_queue) and a warning when it actually
gets put into the bitmap.
The consequence of this bug is that full HW queues associated
with such a too-high mac80211 number never stop higher layer
queues when full, and thus would simply drop all packets that
couldn't be enqueued to the hardware queue.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.
Fix this by setting the A-MSDU bit before the offload bits.
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have tracing for both pre-ICT and ICT interrupts, including all
the data read there. Extend the tracing to MSI-X interrupts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When hostapd adds a station, it does so before sending the association
response frame, so that it can indicate the correct status code in the
response.
However, when this then fails, or the association response already is
a reject for some other reason, then there's no station entry and thus
no per-station management queue to send the response on and it must be
sent on the probe response queue. The code should therefore not warn.
In theory, we could check and warn if the status code is success, but
that seems excessive, so just relax the check to allow any association
response frames.
Fixes: 3ee0f0e23e ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Only a000-series devices were going to use this, but actually
initialize using the context info, which includes paging, so
this code is never invoked; remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we now support 8 device families, move their configuration
files into a new subdirectory "cfg".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the notification wait code into the new fw interaction directory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's a lot of mvm code that really should be more generic
and part of the iwlwifi module. Start by making a place to
keep such code - in the new "fw" subdirectory - and already
move the firmware related header files there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This structure represents V2, V1 has the three last fields missing.
Rename it to be more accurate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the first frame on a given TID is received with seqno 0 and needed
to be retransmitted, we erroneously drop it because the deduplication
data is initialized to zero, and then comparing
if (unlikely(ieee80211_has_retry(hdr->frame_control) &&
dup_data->last_seq[tid] == hdr->seq_ctrl &&
dup_data->last_sub_frame[tid] >= sub_frame_idx))
return true;
will return in iwl_mvm_is_dup() since last_sub_frame is also set to
zero, and sub_frame_idx is usually zero since this only covers the
relatively rare case of A-MSDU.
Fix this by initializing the last_seq array to 0xffff, which is an
impossible value for hdr->seq_ctrl to have here because the lower
four bits are the fragment number, and fragments aren't handled in
this code but go to mac80211 instead.
Fixes: a571f5f635 ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In commit b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work
as expected"), the code was changed to make the stop conditional
on not having failed (and on not having init_dbg), which doesn't
make sense - we should stop the device regardless of failures.
Failure to do so is leading to the device being enabled when it
shouldn't be, and - if it gets re-enabled later - the new context
info code gets confused as paging data wasn't freed.
Remove the invalid error condition again.
Fixes: b93b1fe3b5 ("iwlwifi: mvm: fix init_dbg flow to work as expected")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This appears to happen in some cases, like when iwlmvm is unloaded and
loaded again without also unloading iwlwifi. Warn in this case and free
the paging data to be able to continue without causing corruption and
kernel crashes due to it (otherwise, paging data is overwritten, but
dram->paging_cnt gets to be twice as big as it should be, and then an
eventual free will crash.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
By setting the pointers to NULL at the end, these functions
are made idempotent.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.
Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The BT_COEX command should not be sent to the INIT
firmware image starting from 8000 family.
The firmware team also requested to send the BT_COEX
command after the PHY_DB_CMD and the PHY_CFG_CMD.
While at it:
s/iwl_send_bt_init_conf/iwl_mvm_send_bt_init_conf/
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print the queue for the existing debug message and add a new
debug message indicating where the RB ended.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A SCD bug was fixed in the A000 family, allowing to
support aggregations of 64 frames (rather than 63).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Print out both queue IDs to be able to see what went wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware supports CDB, PHY contexts cannot be modified to
change their band, but need to be added/remove instead. Instead of
relying on iwl_mvm_has_new_tx_api(), check the right FW capa flag
IWL_UCODE_TLV_CAPA_BINDING_CDB_SUPPORT and remove the comment.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new a000 2ax series and add
the five PCI ID for it.
Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no reason to pass mvm and trig as parameters to the macro,
since it will be expanded inside the function itself. Also remove the
bogus buf parameter which doesn't exist and is not used.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The sta_id variable is used as an index in an array, should be unsigned.
Found by Klocwork.
Fixes: 9f9af3d7d3 ("iwlwifi: mvm: re-aggregate shared queue after unsharing")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A hardware issue on 9000 series devices sometimes causes RF-kill
interrupts to not be propagated to the host properly if ASPM is
enabled. Work around this by setting the right hardware bit to
allow it to interrupt the host for this reason (rfkill).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to a hardware issue, certain power saving had to be
disabled. However, this issue was fixed in B-step, so the
workaround only needs to apply to A-step.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some static checkers (e.g. smatch) complain if a non-constant
format string is used, even if that's a static const variable.
Since there's no impact on code generation, just change those
format strings to be macros.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the kernel-doc, and remove some fields even the firmware doesn't
use in ToF, RX, scan, station and generic FW APIS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix various "Excess struct/union/enum/typedef member '...' description
in '...'" warnings from kernel-doc, mostly caused by typos.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a debugfs entry to get a verbose description of the power settings
used in each band with the currently selected SAR geographic profile.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are going to add debugfs entry to retrieve the current geographic
profile being used in the FW. Currently the driver reads those tables
from the BIOS and passes them to the FW.
To prepare for this retrieving we want to store those
tables in the driver.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
-----BEGIN PGP SIGNATURE-----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=DdqX
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
More iwlwifi patches for 4.13
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZT/ROAAoJEG4XJFUm622b/IwH+wQtBXP+P57DZ97BdETcZ3Wd
ejm9KKT3IxcP7kzItT9UR1zv7LNx4NgSkJMfhf37jJ1WIuE2fp/ctNv6mz3PvohW
jD1fLynwEMMC7PLHEy5+xGtL61KYc2mtXs/bfLFl94hZUiaocrsBDIT4fXoyIWif
y3MUlBKDbHA27ULRd485C0MRekRSvR/rq6iST4KsIsa8RflJbdH64teTEnQPp4kh
nvhfnaxVEqHK7mYbarC58yYLNOU8gfQXmeeTfd6jhCXRjfEw37IvtNC8BT4B9ZDX
YMZLbkeDSwNGXIH7EIrpGOYHCPh+qsiJ+sx7YodomcJvd1nVrmbuZZt9/EqWXuY=
=Fd/c
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
New features and bug fixes to quite a few different drivers, but
nothing really special standing out.
What makes me happy that we have now more vendors actively
contributing to upstream drivers. In this pull request we have patches
from Broadcom, Intel, Qualcomm, Realtek and Redpine Signals, and I
still have patches from Marvell and Quantenna pending in patchwork. Now
that's something comparing to how things looked 11 years ago in Jeff
Garzik's "State of the Union: Wireless" email:
https://lkml.org/lkml/2006/1/5/671
Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
brcmfmac
* add support multi-scheduled scan
* add scheduled scan support for specified BSSIDs
* add support for brcm43430 revision 0
wlcore
* add wil1285 compatible
rsi
* add RS9113 USB support
iwlwifi
* FW API documentation improvements (for tools and htmldoc)
* continuing work for the new A000 family
* bump the maximum supported FW API to 31
* improve the differentiation between 8000, 9000 and A000 families
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to TX through a monitor interface, the
conditions in iwl_mvm_tx_skb_non_sta() don't match
and the frame tries to go out from an usued TXQ.
Add a check for monitor iface, and use the AUX queue
in such a case.
In non-DQA mode the frame is sent through the
static-allocated queues anyway, so the problem is
in DQA mode only.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some platforms, having the device enabled with certain radio
frontends causes the platform to not be able to resume properly
from suspend, regardless of the wakeup cause. This was traced to
a hardware issue with the integrated 9000-series A-step variant.
Set the right hardware bit to disable the problematic state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware crashes, the transmit queues can't make
any progress. This is why we stop the counter that monitor
the transmit queues' activity.
The call that notifies the error to the op_mode may take
a bit of time, so stop the timer of the transmit queues
earlier.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver prints "L1 Enabled - LTR Enabled" all the time as dev_info,
which is just useless noise in most cases. Convert this to
IWL_DEBUG_POWER() so we don't pollute the log unnecessarily but still
can get this info on demand.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's sometimes hard to find out which HW address the iwlwifi device is
using, for instance when reading crouded sniffer logs. To make it
easier, print out an info level message with the HW address as soon as
we know it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API allows flushing queues based on station ID and TID in A000
devices. One reason for using this is that tfd_queue_mask is only good
for 32 queues, which is not enough for A000 devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get an ASSERT, the fw_dump_desc pointer points to
iwl_mvm_dump_desc_assert which can't be freed since it is
a global. We still need to NULL'ify the pointer when we
call iwl_mvm_free_fw_dump_desc otherwise we will hit
int iwl_mvm_fw_dbg_collect_desc(struct iwl_mvm *mvm,
const struct iwl_mvm_dump_desc *desc,
const struct iwl_fw_dbg_trigger_tlv *trigger)
{
<snip>
if (WARN_ON(mvm->fw_dump_desc))
iwl_mvm_free_fw_dump_desc(mvm);
Fixes: b6eaa45aa1 ("iwlwifi: mvm: add the cause of the firmware dump in the dump")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When updating the mac context after association,
assoc_beacon_arrive_time is not being set, which causes the FW to
set a wrong TSF to the MAC.
Fix this by setting the assoc_beacon_arrive_time when updating the
mac context after association.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing ever checks the return value of iwl_pcie_apm_stop_master(),
so there's no point in it having one - make it return void.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we need to move the scheduler write pointer by
steps of 0x40, 0x80 or 0xc0, the scheduler gets stuck.
This leads to hardware error interrupts with status:
0x5A5A5A5A or alike.
In order to work around this, detect in the transport
layer that we are going to hit this case and tell iwlmvm
to increment the sequence number of the packets. This
allows to keep the requirement that the WiFi sequence
number is in sync with the index in the scheduler Tx queue
and it also allows to avoid the problematic sequence.
This means that from time to time, we will start a queue
from ssn + 1, but that shouldn't be a problem since we
don't switch to new queues for AMPDU now that we have
DQA which allows to keep the same queue while toggling
the AMPDU state.
This bug has been fixed on 9000 devices and up.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A TID may not have traffic but still have a BA agreement
active (or being setup / torn down) since a BA agreement
can be triggered by a debugfs hook.
Just avoid to consider such a TID as inactive to make the
logic safer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the hardware is stuck, we can't read any of the memory we need to
dump it, so we end up printing only 0xa5a5a5a5, which is useless.
To solve this, poke the hardware by triggering a reset and re-enabling
the clocks if we detect a HW error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we started using threaded irqs, all the opmode calls were changed
to be called with local_bh disabled. The reason for this was it was
that mac80211 needs that. When we are handling FW errors, mac80211 is
not involved, so we don't need it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In BSS mode in the disconnection flow, mac80211 removes
the AP station before the vif is set to unassociated.
Our firmware wants it the other way around: first set
the vif as unassociated, and then remove the AP station.
In order to bridge between those two different behaviors,
iwlmvm doesn't remove the station from the firmware when
mac80211 removes it, but only after the vif is set to
unassociated. The implementation is in
iwl_mvm_bss_info_changed_station:
if (assoc state was modified && mvmvif->ap_sta_id is VALID
&& assoc state is now UNASSC)
remove_the_station_from_the_firmware()
During the recovery flow, mac80211 re-adds the AP station
and then reconfigures the vif. Since the vif is not
associated, and then, we enter the if above (which was
intended to be taken in the disconnection flow only) and
remove the station we just added. This defeats the
recovery flow.
Fix this by not removing the AP station in this flow if
we are in recovery flow.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We allocate nvm_data in iwl_mvm_nvm_get_from_fw(). If something goes
wrong after the allocation (i.e. if no valid MAC address is valid), we
should free nvm_data before returning an error.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function just calls kfree(), so it only obscures the code without
bringing any benefits. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Properly document the transmit buffer bits using an enum and
kernel-doc documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add kernel-doc documentation for enum iwl_debug_cmds, linking the
structures used by the commands.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This improves documentation, since kernel-doc can't deal with the
union well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To stop and start the FW monitor in the 7000 HW
family we need to use a different bit, otherwise
after stopping it for the first time - it won't
get restarted. Use the correct bitmask.
Note: This fix is only for DRAM collection mode.
For other modes, an additional fix will be
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the enum link by adding the missing & and provide the link
to the TX response documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the command name is printed on command completion, the wrong
group is used, leading to the wrong name being printed. Fix this
by using the group ID without inappropriately mangling it through
iwl_cmd_groupid() - it's already a u8. Also, while at it, use it
from the same place as the command ID, everything else is just
confusing.
Fixes: ab02165cce ("iwlwifi: add wide firmware command infrastructure for TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending non-linear SKBs that should be included in the regular
TX tracing completely (and not be pushed into the tx_data tracing),
the (tracing) code didn't correctly take the fact that they were
non-linear into account and added only the skb head portion.
This probably never really triggered, since those frames we want
traced fully are most likely linear anyway, but the code gets easier
to understand and we lose an argument to the tracing function, so
overall fixing this is better.
Fixes: 206eea7833 ("iwlwifi: pcie: support frag SKBs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to calculate the data_len outside of the tracepoint,
since it's always skb->len - hdr_len, which are both available inside.
Simplify the callers and move the calculation in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Show the name of the member (scanned_channels) that provides the
length with some better markup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use kstrtou32_from_user() in debugfs instead of open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.
Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we happen to be in or get into the queue sync when RF-kill
is asserted, we return from there and warn since there are
still queue sync notifications outstanding. These can't ever
come though, because we're in RF-kill, so don't WARN then.
While at it, also move the warning to the appropriate place,
if the request is not synchronous then we shouldn't warn, but
currently always will.
To make it fast, also trigger the waitq when on rfkill assert.
Fixes: 0636b93821 ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in duplicating exactly the same code here
for legacy and MSI-X interrupts, so pull it out into a new
function to call in both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case that rate's antenna is wrong at the init stage, it's
very hard to say what went wrong. Add debug data to the already
existing WARN_ON_ONCE.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some static checkers (e.g. smatch) complain about the logic, saying that
resp_cp might be leaked. Clearly that isn't true, but making the logic
easier to follow does not result in any significant code changes and makes
the code more readable by moving the NULL check closer to its source.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware moved the development from a0 MAC to z0.
z0 is using the same RFID and device ID as a0 so we only
need to switch the name.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New FW versions require the D0I3_END_CMD to be sent as the first
command to the FW in the resume flow. If the TLV is set, send that
command first, otherwise keep the original behavior (i.e. send last).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no need to send D0I3_END_CMD as ASYNC during the system
resume flow. Additionally, the other flags used are meaningless in
this case (they were just copied from the runtime resume flow), so
remove them all.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Shaul reported that when iwlmvm was sending beacons, it didn't properly
also take ownership of the probe responses. This is because the whole
mac80211 callback (tx_last_beacon) wasn't implemented. Fix that to make
IBSS discovery work better.
Reported-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's safer to use scnprintf() here because the buffer might
be too short for the full format strings. In most cases
this isn't true because of external limits on the values.
In one case, this fixes a stack data leak.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid one kind of symbol shadowing another in iwl_mvm_flush_sta()
by renaming the function parameter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The queue ID should never be 512 either, so correct the check
to be >= instead of just >.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since we exit if buf->num_stored is 0, there's no need to
check it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending a Tx Command with a Tx packet, we allocate the
Tx command separately from the payload of the packet.
The WiFi MAC header is then copied into the buffer that was
allocated for the Tx Command. This means that this buffer
needs to be big enough to contain both. This is why it is
allocated with iwl_trans_alloc_tx_cmd which returns a
pointer to a newly allocated not zeroed struct
iwl_device_cmd.
The Tx command has a few bit fields and hence it needs to
be zeroed, but all the rest of the buffer doesn't need to
be zeroed since it will either be memcopy'ed with the MAC
header, or not even sent to the device.
This means that we don't need to zero all the
iwl_device_cmd structure, but rather only the size of
the iwl_tx_cmd structure.
Since sizeof(iwl_tx_cmd) - sizeof(iwl_tx_cmd) is about
260 bytes, this can avoid touching 4 cache lines for each
packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Install GTKs on AP side for new TX API.
Don't add IV space, it's added by the HW.
While at that fix GCMP abnd GCMP-256 GTK installation
which work similarly to the new TX API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If FW isn't alive, trying to collect debug data will
result in errors both in driver and in the collected
data, so just warn and leave the collecting function
in this case.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Contrary to what some of the comments say, if rfkill was
asserted the transport will return -ERFKILL instead of
success, if CMD_WANT_SKB was set, so it's not necessary
to check cmd.resp_pkt for being NULL if the return code
was success.
Validate that this is true in iwl_trans_send_cmd().
Most of the other code modifications were done with the
following spatch:
@@
struct iwl_host_cmd cmd;
identifier pkt;
@@
<...
(
pkt = cmd.resp_pkt;
...
-if (!pkt) { ... }
|
pkt = cmd.resp_pkt;
...
-if (WARN_ON(!pkt)) { ... }
|
-if (!cmd.resp_pkt) { ... }
)
...>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, there is no need to wait for the TXQ to
clear out after getting a DELBA, since traffic can
continue running on the queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
-----BEGIN PGP SIGNATURE-----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=oYeO
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi driver patches 4.13
* Loads of FW API documentation improvements (for tools and htmldoc);
* Continued work for the new A000 family;
* Bumped the maximum supported FW API to 31;
* Improve the differentiation between 8000, 9000 and A000 families;
* A lot of fixes and cleanups here and there;
kvalo: There were conflicts iwl_mvm_stop_device() and
iwl_mvm_tcool_set_cur_state(). The former was easy but latter needed more
thought. Apparently the mutex was taken too late, so I fixed so that the mutex
is taken first and then check for iwl_mvm_firmware_running().
We are trying to get rid of DRIVER_ATTR(), and the ipw2x00 driver's
attributes can be trivially changed to use DRIVER_ATTR_RW().
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: <linux-wireless@vger.kernel.org>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZPpCkAAoJEG4XJFUm622bUTMH/ipenw7p7otrhw9qtSBcqBRJ
hS+1i2J+VXDXptFng0ziPWVv6mvhANvBszuOmiNMOgqjx2HrVknwlKUKViklHN3p
E1PE3/A3bRpzBjMk4j8r/Z7VJK3rDa4WSi/AMJtqV9noNm5FfiOrCk7rXm2MLBns
x1Wyr/7OX12hiB4SCoOuOZqS/TvHlNCW71BoyRruq01N2MA1iSonLCYJbovgi7Ds
9acAY90PF8jLC+o7wxYkwuRqWncNhnKOsVNhc/6DKH91zB+C5sw2NGfD3WMfot/Z
9uC5nBWNadoLGi636y+9evIRgNAFCczCZZSUeY7jMWiVn7XyFy8zoc4fv2ZSBto=
=6md1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-06-12' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
The first pull request for 4.13. We have a new driver qtnfmac, but
also rsi driver got a support for new firmware and supporting ath10k
SDIO devices was started.
Major changes:
ath10k
* add initial SDIO support (still work in progress)
rsi
* new loading for the new firmware version
rtlwifi
* final patches for the new btcoex support
rt2x00
* add device ID for Epson WN7512BEP
qtnfmac
* new driver for Quantenna QSR10G chipsets
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When we removed dev_cmd_headroom, the check for dev_cmd_ptr == NULL
became unnecessary, since we just return dev_cmd_ptr anyway. Cleanup
the function to avoid useless code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The include in the deleted file are included in the fw-api.h file.
Which caused a cycle include in the dependencies.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware no longer uses this command group, so remove it from
the driver as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link from the TX_CMD enum value to the TX command structs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Document which structures are used with the command for
the A000 hardware flavour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
