The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially in this code, the race didn't matter since it didn't
do anything. Latest with the commit I marked this as fixing it
started to matter as something got done here that needed other
data that got freed as soon as the queue notification wait was
returning.
In the scenario we saw, apparently the IWL_MVM_RXQ_NOTIF_DEL_BA
event was sent to all queues, but processing the last event we
returned from iwl_mvm_sync_rx_queues_internal() and then from
iwl_mvm_free_reorder() and continued some processing before
wl_mvm_del_ba() was even invoked on the other CPU. Thus, when
the latter finally ran, it found that mvm->baid_map[baid] was
no longer valid.
Correct the race by moving the counter decrement and wake_up()
to be done only after all the per-event processing completed.
Note that in the commit I marked as being fixed the wake_up()
didn't exist yet (and the code was otherwise problematic) but
this particular problem already existed in a way.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A peer can limit the number of subframes it can handle in a
single A-MSDU. Honor this limit.
Note that the smallest limit is 8, and we are very unlikely to reach
that limit. So this isn't really a big deal.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, a BA session is opened when the tx traffic exceeds
10 frames per second. As a result of inter-op problems with some
APs, add a condition to open BA session only when station is
already authorized.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our hardware has a limited amount of buffer descriptors
for each Tx packet. Because of that, there is a short
piece of code that makes sure that that we don't push too
many subframes in an A-MSDU because of subframes needs 2
buffer descriptors. This code also takes into account the
number of fragment of the skb since we also need a buffer
descriptor for each fragment in the skb.
This piece of code though didn't check that the resulting
number of subframes wasn't 0.
A user reported that using NFS client, he could get skbs
that are so fragmented that the code mentioned above
returned 0 for the number of subframes making
skb_gso_segment fail and subconsequently iwlwifi would WARN.
Fix this by make sure that num_subframes is at least 1.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=199209
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some versions of the FW don't support channel switch in TDLS.
Add a condition that checks it.
Fixes: 307e47235a ("iwlwifi: mvm: configure TDLS peers to FW")
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some cases we may get from FW errored frames with
UNKNOWN security type.
This may happen in unsecured aggregation flow, where
the first packet had a CRC error in the WEP bit, which
was followed by a failure to decrypt and was dropped.
The next frames in the aggregation "inherit" the bad metadata
of the first packet.
Make sure to drop such frames since RADA and other offloads
will not operate correctly which may have unexpected results.
In case of AP it also causes to TX AMSDU frames to the peers,
resulting with assert 0x104B.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are specific cases, such as SAE authentication exchange, that
might require long duration to complete. For such cases, add support
for indicating to the driver the required duration of the prepare_tx()
operation, so the driver would still be able to complete the frame
exchange.
Currently, indicate the duration only for SAE authentication exchange,
as SAE authentication can take up to 2000 msec (as defined in IEEE
P802.11-REVmd D1.0 p. 3504).
As the patch modified the prepare_tx() callback API, also modify
the relevant code in iwlwifi.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of "any" wowlan trigger is configured, no valid wakeup filter
was configured.
Moreover, the fw assumes there's no connection when there are no configured
wakeup filters.
This leads to the station info not being updated on D3 command, causing
rate_n_flags to be 0 when the offloading code sends tx frame (triggering
SYSASSERT_102C due to invalid antenna param)
Note: "any" trigger is currently assumed to only be used when entering
d0i3 (which has a different flow). However, we still reach this code
when using d3_test.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Firmware will only send non low-latency TIDs in the
bitmap, so the check is now redundant.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Future changes will require moving the HE radiotap data into
the SKB head, but this means we need to have the alignment
reservation done before that. To prepare, move the alignment
reservation earlier here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future devices a new image will be introduced - IML. The IML, image
loader, is loaded by the ROM, and as part of the new self-init flow,
loads the rest of the firmware images to the device.
Store the image, so the ROM can load it to the device.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To fix a conflict reported by Stephen Rothwell <sfr@canb.auug.org.au>:
Today's linux-next merge of the wireless-drivers-next tree got a
conflict in:
drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
between commit:
77e30e10ee ("iwlwifi: mvm: query regdb for wmm rule if needed")
from the wireless-drivers tree and commits:
9c4f7d5127 ("iwlwifi: move all NVM parsing code to the common files")
4c625c564b ("iwlwifi: get rid of fw/nvm.c")
from the wireless-drivers-next tree.
When trying to open aggregations on 22000 HW before
traffic had actually passed, the driver will discover
it is missing a queue to aggregate on. In such a case -
allocate a queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's already an opmode common file for nvm iwl-nvm-parse.c
Move the content of fw/nvm.c to iwl-nvm-parse.c and delete fw/nvm.c.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update rs-fw API to match changes in FW. Specifically, the
TLC_MNG_NOTIF_REQ_CMD command and TLC_MNG_AMSDU_ENABLE_NOTIF
notification are removed, the A-MSDU related info is received from FW
via the TLC_MNG_UPDATE_NOTIF, and the TLC_MNG_CONFIG_CMD uses version
2 of its data structure.
Additionally, constify some arguments in a couple of functions.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22000 devices rely on this flag to install the key to the right
queues. For earlier devices we didn't have a key / queue mapping and
the key was sent along with the Tx command for each Tx hence the
problem didn't arise.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This saves some typing and is overall more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move all the NVM file handling code to iwl-nvm-parse.c where all this
stuff belongs. This cleans up the MVM specific code and allows easier
reuse by other opmodes if needed.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22000 devices, aka gen2, the TFS is 256 bytes.
In order to save memory, use shorter TX queue for aux and
mgmt queues, since there isn't much traffic on them.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for dynamic queue sizing, add a parameter
of the TX queue size to the dynamic queue allocation op
mode API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new APIs and activate AMSDU based on the
offloaded TLC decisions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code that sets the correct out-of-channel priority depending on
the scan type was accidentally removed during a rebase. Add it back.
Fixes: c1a7515393 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Introduce and use iwl_mvm_cdb_scan_api(), which checks the family.
Most of this will go away once the 22000 firmware supports adaptive
dwell, after which the V6 scan API won't be used, but the V3 scan
*config* API will still need to be distinguished.
In any case, this gets rid of the completely bogus has_new_tx_api()
checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Detect low latency and traffic load per band. Add support for
deciding on scan type and timings per band.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Try to detect that the AP is not using aggregation even when there's
enough traffic to make it worthwhile; if this is the case and U-APSD
is enabled then assume the AP is broken (like so many) and doesn't
enable aggregation when U-APSD is used. In this case, disconnect from
the AP and blacklist U-APSD for a potential new connection to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The primary channel is the channel that will be untouched by BT. The
secondary channel might be touched by BT. Hence, we want the primary
to be the most active channel. To do so, use the TCM infrastructure.
Since the BT keeps sending notifications, we can rely on them to
trigger the check. Every 10 seconds, we will check what is the most
active context and chose the right primary.
We need to wait 10 seconds before we modify the settings because
frequent changes in these settings can confuse BT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code for changing the scan priority is already implemented, but
isn't yet in use. Now that TCM data is available, we can base the
scan priority decision on the traffic load.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Traffic condition monitor gathers data about the traffic load and
other conditions and can be used to make decisions regarding latency,
throughput etc. This patch introduces the code and data structures to
collect this data for future use.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since our device is regulatory self managed it maintains its regulatory
rules by its own. However the wmm_rules values can't be set by the
device itself but only the indication about the need to set it.
In case the device set wmm indication, proactively query the regulatory
data base to get these values
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-31
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add raw BPF tracepoint API in order to have a BPF program type that
can access kernel internal arguments of the tracepoints in their
raw form similar to kprobes based BPF programs. This infrastructure
also adds a new BPF_RAW_TRACEPOINT_OPEN command to BPF syscall which
returns an anon-inode backed fd for the tracepoint object that allows
for automatic detach of the BPF program resp. unregistering of the
tracepoint probe on fd release, from Alexei.
2) Add new BPF cgroup hooks at bind() and connect() entry in order to
allow BPF programs to reject, inspect or modify user space passed
struct sockaddr, and as well a hook at post bind time once the port
has been allocated. They are used in FB's container management engine
for implementing policy, replacing fragile LD_PRELOAD wrapper
intercepting bind() and connect() calls that only works in limited
scenarios like glibc based apps but not for other runtimes in
containerized applications, from Andrey.
3) BPF_F_INGRESS flag support has been added to sockmap programs for
their redirect helper call bringing it in line with cls_bpf based
programs. Support is added for both variants of sockmap programs,
meaning for tx ULP hooks as well as recv skb hooks, from John.
4) Various improvements on BPF side for the nfp driver, besides others
this work adds BPF map update and delete helper call support from
the datapath, JITing of 32 and 64 bit XADD instructions as well as
offload support of bpf_get_prandom_u32() call. Initial implementation
of nfp packet cache has been tackled that optimizes memory access
(see merge commit for further details), from Jakub and Jiong.
5) Removal of struct bpf_verifier_env argument from the print_bpf_insn()
API has been done in order to prepare to use print_bpf_insn() soon
out of perf tool directly. This makes the print_bpf_insn() API more
generic and pushes the env into private data. bpftool is adjusted
as well with the print_bpf_insn() argument removal, from Jiri.
6) Couple of cleanups and prep work for the upcoming BTF (BPF Type
Format). The latter will reuse the current BPF verifier log as
well, thus bpf_verifier_log() is further generalized, from Martin.
7) For bpf_getsockopt() and bpf_setsockopt() helpers, IPv4 IP_TOS read
and write support has been added in similar fashion to existing
IPv6 IPV6_TCLASS socket option we already have, from Nikita.
8) Fixes in recent sockmap scatterlist API usage, which did not use
sg_init_table() for initialization thus triggering a BUG_ON() in
scatterlist API when CONFIG_DEBUG_SG was enabled. This adds and
uses a small helper sg_init_marker() to properly handle the affected
cases, from Prashant.
9) Let the BPF core follow IDR code convention and therefore use the
idr_preload() and idr_preload_end() helpers, which would also help
idr_alloc_cyclic() under GFP_ATOMIC to better succeed under memory
pressure, from Shaohua.
10) Last but not least, a spelling fix in an error message for the
BPF cookie UID helper under BPF sample code, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fix iwlwifi_dev_ucode_error tracepoint to pass pointer to a table
instead of all 17 arguments by value.
dvm/main.c and mvm/utils.c have 'struct iwl_error_event_table'
defined with very similar yet subtly different fields and offsets.
tracepoint is still common and using definition of 'struct iwl_error_event_table'
from dvm/commands.h while copying fields.
Long term this tracepoint probably should be split into two.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently we have a boolean variable for each cause.
This costs space, and requires to check each separately
when determining low latency.
Since we have another cause incoming, convert it to an enum.
While at it, move the retrieval of the prev value and the
assignment of the new value to be inside iwl_mvm_update_low_latency
and save the need for each caller to do it separately.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove fragmented_dwell_time and add num_of_fragments to support
the new API version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW does not allocate quota air time for the binding of a station
MAC before iwlmvm indicates that it is associated. Currently iwlmvm
indicates that the MAC is associated only after hearing a beacon from
the AP. In case a deauthentication frame is sent before the MAC is
associated, the frame might not be sent as the corresponding binding
is not scheduled.
To handle such cases, set IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP in the
HW flags, requesting mac80211 to call the mgd_prepare_tx() callback
before transmitting a deauthentication frame if associated but no
beacon was heard from the AP.
In addition, do not warn in iwl_mvm_mac_mgd_prepare_tx() when already
associated as now the callback can be called also when associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for Optimized Connectivity Experience (OCE). Get
capabilities from the fw, expose them with nl80211, and enable them in
UMAC scan if the relevant nl80211 flags are set by the userspace.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update the scan command API with support for adaptive dwell. Adaptive
dwell is a type of scan that dynamically changes the time it remains
on each channel listening for beacons or probe responses.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes iwl_mvm_disable_txq() may be called with mac80211_queue ==
IEEE80211_INVAL_HW_QUEUE, and this would cause us to use BIT(0xFF)
which is way too large for the u16 we used to store it in
hw_queue_to_mac820211. If this happens the following UBSAN warning
will be generated:
[ 167.185167] UBSAN: Undefined behaviour in drivers/net/wireless/intel/iwlwifi/mvm/utils.c:838:5
[ 167.185171] shift exponent 255 is too large for 64-bit type 'long unsigned int'
Fix that by checking that it is not IEEE80211_INVAL_HW_QUEUE and,
while at it, add a warning if the queue number is larger than
IEEE80211_MAX_QUEUES.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Reported-by: Paul Menzel <pmenzel+linux-wireless@molgen.mpg.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes future bail-outs from transmitting an AMSDU more
readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When immediate quiet bit is set in CSA, the entire channel is blocked
by the firmware. It is expected that all the MACs will evacuate the
channel and the phy will be eventually either moved or removed.
Currently, the phy context is just unreferenced and thus, the quiet
bit is kept set and it will be impossible to TX on this phy, if we
will need to reuse it in the future. This can be seen when doing a
channel switch with mode=1 (quiet) twice from channel X to Y and then
back to channel X.
Fix that, by moving the phy context to a default channel when not
referenced anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.
While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.
Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a queue is reserved for aggregation, the queue id is assigned
to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper()
takes care of allocating the queue before actual tx starts.
When the reservation is cancelled (e.g. when the AP declined the
aggregation request) the tid_data is not cleared. As a result,
following tx for this tid was trying to use an unallocated queue.
Fix this by setting the txq_id for the tid to invalid when unreserving
the queue.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.
Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations. We need to set a bit in the phy
configuration to indicate that to the FW. To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware. And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.
Fixes: c62446d2b0 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.
Found by smatch:
.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.
The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.
To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.
Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the scheduler config command, the meaning of tid == 0xf was intended
to indicate the configuration is for management frames. However,
tid == 0xf was also used for the multicast queue that was meant only
for multicast data frames, which resulted with the FW not encrypting
multicast data frames.
As multicast frames do not have a QoS header, fix this by setting
tid == 0, to indicate that this is a data queue and not management
one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Multicast frames for NL80211_IFTYPE_AP and NL80211_IFTYPE_ADHOC were
directed to the broadcast station, however, as the broadcast station
did not have keys configured, these frames were sent unencrypted.
Fix this by using the multicast station which is the station for which
encryption keys are configured.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the GTK is installed, we install it to HW with the
station ID of the AP.
Mac80211 will try to remove it only after the AP sta is
removed, which will result in a failure to remove key
since we do not have any station for it.
This is a valid situation, but a previous commit removed
the early return and added a return with error value, which
resulted in an error message that is confusing to users.
Remove the error return value.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trying to collect firmware debug data while firmware
is not loaded causes various errors (e.g. failing NIC access).
This causes even a bigger issue if at that time the
HW radio is off.
In that case, when later turning the radio on, the Driver
fails to read the HW (registers contain garbage values).
(It may be that the CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN
bit is cleared on faulty NIC access - since the same behavior
was seen in HW RFKILL toggling before setting that bit.)
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We should add the multicast station before adding the
broadcast station.
However, in older FW, the firmware will start beaconing
when we add the multicast station, and since the broadcast
station is not added at this point so the transmission
of the beacon will fail on assert 0x2b00.
This is fixed in later firmware, so make the order
of addition depend on the TLV.
Fixes: 26d6c16bed ("iwlwifi: mvm: add multicast station")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It was assumed that apply_time==0 implies immediate scheduling, which is
wrong. Instead, the fw expects the START_IMMEDIATELY flag to be set.
Otherwise, this resulted in 0x3063 assert.
Fix that.
While at it rename the T2_V2_START_IMMEDIATELY to
TE_V2_START_IMMEDIATELY.
Fixes: f5d8f50f27 ("iwlwifi: mvm: Fix channel switch in case of count <= 1")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't have enough room in the TX command for a CCMP 256
key, and need to use key from table.
Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While entering to D3 mode there is a gap between the time the
driver handles the D3_CONFIG_CMD response to the time the host is going
to sleep.
In between there might be cases which MARKER_CMD can tailgate.
Also during resume flow the MARKER_CMD might get sent while D0I3_CMD
is being handled in the FW.
Cancel MARKER_CMD timer and set it again properly during suspend
resume flows to prevent this command from being sent accidentlly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Canceling the periodic timestamp work should be
done in the opposite flow to where it was started.
This also prevents from sending the MARKER command
during the mac_stop flow - causing a false queue hang
(FW is no longer there to send a response).
Fixes: 93b167c13a ("iwlwifi: runtime: sync FW and host clocks for logs")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In IBSS, the mac80211 sets the cab_queue to be invalid.
However, the multicast station uses it, so we need to override it.
A previous patch did it, but it was nested inside the if's and was
applied only for legacy FWs that don't support the new station type
API, instead of being applied for all paths.
In addition, add a missing NL80211_IFTYPE_ADHOC to the initialization
of the queues in iwl_mvm_mac_ctxt_init()
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.
This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.
Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.
Fixes: f1ae02b186 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This aligns the code with the existing pattern to check
if the firmware has a certain capability.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently a new command was added to the firmware
for setting a MAC's low-latency mode. Use it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have TSO enabled, we might end up segmenting it and
queuing multiple packets before the queue is even enabled. This causes
a warning.
For example, when starting TCP traffic on a non-zero TID, the
first packets may not have DSCP and will be sent on TID 0, while
the actual data packets will be sent on the TID.
To prevent this, simply remove the warning.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Latest firmware calculates both phases of the TKIP
field, so the TTAK ok flag is not needed and deprecated.
Support this API change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For sync we send a marker cmd every <defined throughout debugfs> seconds.
The trigger for getting gp2 clock values from the FW is set by
writing to debugfs a periodic time in seconds,
if value zero is written, only one request would be sent
and the timer would be canceled.
Also added a small infrastructure for debugfs runtime code.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The way p2p NoA is forced in SCM (used for WFA tests)
is by setting a quota < 100% (simulating DCM).
A test-mode command is used for setting the NoA params.
In that case, force quota update or nothing will happen
if there was no significant change in the quota
at that exact point (which is likely to be the case).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.
Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support internal debug data collection on 9000 and newer
devices.
The method for finding the base and end address has changed
on new HW's, so introduce a new version of debug destination
tlv.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidentally pushed a patch with CPTCFG (which is used in the
backports project) to the rs-fw.c file. Fix that to use CONFIG
instead.
Fixes: 9f66a397c8 ("iwlwifi: mvm: rs: add ops for the new rate scaling in the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When statistics are read from debugfs, make sure that they
are actually updated from the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If FW loads without a problem, leaving init_dbg on can
cause a confusion, since the user won't necessarily
remember it is still turned on, and there are flows in
which everything continues as usual, only without
stopping the device after INIT, even if there is no FW
assert. On 22000 HW, for instance, this causes a
warning, since the paging is getting initialized twice.
Solve the issue by making this module param effective
only if the FW indeed asserts during INIT.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending LQ command, verify the rate scaling is not in firmware.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch sends to the FW notification configuration command and
handles the update responses.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch adds rate scaling configuration command and
implements a few other handlers.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the series will fill in the implementation).
The decision which API to use is done during the register
step according to FW TLV.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New devices will have rate scaling algorithm running in the firmware.
With this feature, the driver's responsiblity is to provide an initial
configuration and to handle notifications regarding recent rates and
some other parameters. Debugfs hooks will be still available for
reading the current rate/statistics and setting a fixed rate.
The old API is supported so far, though both APIs cannot be used
simultaneously.
This is the first patch in the series. It adds a new TLV specifying
FW support for the new API and updates lq_sta to support two types
of rate scaling.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We might erroneously get to error dumping code when the
device is already stopped.
In that case the driver will detect a defective value and will try to
reset the HW, assuming it is only a bus issue. The driver than
proceeds with the dumping.
The result has two side effects:
1. The device won't be stopped again, since the transport status is
already stopped, so the device remains powered on while it actually
should be stopped.
2. The dump in that case is completely garbaged and useless.
Detect and avoid this. It will also make debugging such issues
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the removal of non-DQA code, we don't need the queues
variable any more. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the WFA vendor specific TPC report IE to probe requests
when it is not added by the FW. The FW will still need to set
the tx power field.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When RADA is active, the hardware decrypts the packets and strips off
the MIC as it is useless after decryption. Indicate that to mac80211.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the flag that indicates that ICV was stripped on if
this option was enabled in the HW.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before deleting a time event (remain-on-channel instance), flush
the queue so that frames cannot get stuck on it. We already flush
the AUX STA queues, but a separate station is used for the P2P
Device queue.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
-----BEGIN PGP SIGNATURE-----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=j1dk
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi updates for v4.16
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
kvalo:
There were conflicts, I fixed them with taking into account commit c2c48ddfc8
("iwlwifi: fix firmware names for 9000 and A000 series hw"):
CONFLICT (content): Merge conflict in drivers/net/wireless/intel/iwlwifi/iwl-config.h
CONFLICT (modify/delete): drivers/net/wireless/intel/iwlwifi/cfg/a000.c deleted in ca495785063c428641cc6df8888afd2587ca6677 and modified in HEAD. Version HEAD of drivers/net/wireless/intel/iwlwifi/cfg/a000.c left in tree.
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since iwl_mvm_start_p2p_roc() is only called from iwl_mvm_roc(),
which already flushes the same work item, doing it again in it
is superfluous. Remove it and move the comment to the first one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This feature was actually removed from firmware, but without
ever telling the driver. Since nobody is actually using it,
just remove it entirely without bothering with a capability
check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API will not be used, remove the code that
supports it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we are in a search cycle, we try different combinations
of parameters. Those combinations are called 'columns'.
When we switch to a new column, we first need to check if
this column has a suitable rate, if not, we can't try it.
This means we must not erase the statistics we gathered
for the previous column until we are sure that we are
indeed switching column.
The code that tries to switch to a new column first sets
a whole bunch of things for the new column, and only then
checks that we can find suitable rates in that column.
While doing that, the code mistakenly erased the rate
statistics. This code was right until
struct iwl_scale_tbl_info grew up for TPC.
Fix this to make sure we don't erase the rate statistics
until we are sure that we can indeed switch to the new
column.
Note that this bug is really harmless since it causes a
change in the behavior only when we can't find any rate
in the new column which should really not happen. In the
case we do find a suitable we reset the rate statistics
a few lines later anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In A000 family, compressed BA notifs can include MGMT
frames, so don't fail RXs in such a case.
While at it, since in A000 the TID for MGMT frames is
15, treat it in the RX flow as if received TID 8. This
way we won't require special handling of this TID.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This bit will be used in CCK to indicate short preamble.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.
Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MONITOR type is missing in the interface type switch.
Add it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we act as an AP, new firmware versions handle
internally the power saving clients and the driver doesn't
know that the peers went to sleep. It is, hence, possible
that a peer goes to sleep for a long time and stop pulling
frames. This will cause its transmit queue to hang which is
a condition that triggers the recovery flow in the driver.
While this client is certainly buggy (it should have pulled
the frame based on the TIM IE in the beacon), we can't blow
up because of a buggy client.
Change the current implementation to not enable the
transmit queue hang detection on queues that serve peers
when we act as an AP / GO.
We can still enable this mechanism using the debug
configuration which can come in handy when we want to
debug why the client doesn't wake up.
Cc: stable@vger.kernel.org # v4.13
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ieee80211_rx_status::chains was always set to zero.
That caused rate scaling to always start with the
lowest rate possible (rs_get_initial_rate).
Set it correctly according to the MPDU response.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
-----BEGIN PGP SIGNATURE-----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=JPn9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
iwlwifi: first set of fixes for 4.15
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Newer firmware versions (such as iwlwifi-8000C-34.ucode) have
introduced an API change in the SCAN_REQ_UMAC command that is not
backwards compatible. The driver needs to detect and use the new API
format when the firmware reports it, otherwise the scan command will
not work properly, causing a command timeout.
Fix this by adding a TLV that tells the driver that the new API is in
use and use the correct structures for it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=197591
Fixes: d7a5b3e9e4 ("iwlwifi: mvm: bump API to 34 for 8000 and up")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
-----BEGIN PGP SIGNATURE-----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=CC8e
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi updates
* Some new PCI IDs;
* A bunch of cleanups;
* The timers update by Kees;
* Add more register dump call-sites;
* A fix for a locking issue in the TX flush code;
* Actual implementation of the TX flush code for A000;
* An optimization to drop RX frames during restart to avoid BA issues;
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a hardware restart the BA session data in HW is lost
so the reorder buffer simply passes the frames to mac80211 as is
as there is no NSSN set. Instead, we will drop these frames
before they reach the reorder buffer. mac80211 drops such frames anyway,
but we shouldn't rely on that. In addition it saves some
processing time
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
The RCU lifetime on baid_data is unclear, so this adds a direct copy of the
rcu_ptr passed to the original callback. It may be possible to improve this
to just use baid_data->mvm->baid_map[baid_data->baid] instead.
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_flush_tx_path() function sends a synchronous command to
the firmware. When doing that, we must hold the mutex. The
iwl_mvm_flush_no_vif() function was mistakenly not holding the mutex.
Fix it.
Fixes: 6110d9e5bd ("iwlwifi: mvm: Flush non STA TX queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the mac flush flow, we should flush all existing queues.
Since FW API for a000 devices is flush per RA-TID, simply
flush all stations with all tids.
From FW perspective, asking to flush a TID that doesn't have
a queue is valid, so we can just set all bits in the TID mask.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is very indented and hard to read.
Refactor it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we return early from sync_rx_queues for a000 devices.
This may cause, in case of a non-empty reorder buffer, a warning
later on since the RX queue isn't getting the notification to
empty it.
A better approach would be to send the notification for the default
queue only.
Do this hard coded for now, until we will have the API to enable
multi queue for a000 devices.
Fixes: bc02946964 ("iwlwifi: mvm: disable RX queue notification for a000 devices")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We had a bunch of code that was relevant for internal
devices only. Those devices are now being depreceated.
Kill all the now unneeded code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When there is a reorder timeout, we may get to a situation
where we have the timeout latency for all the next 64 frames.
This happens since NSSN is behind for a while, and the driver
won't release the frames, since it is not allowed by NSSN.
As a result the frame is stored in the reorder buffer although
there is no hole, and released 100 ms later.
Add a direct comparison to the reorder buffer head, and release
immediately if possible.
For example:
Frame 0 is missed. We receive frame 1, and store it in the buffer.
After 100 ms, frame 1 is released and reorder buffer head is 2.
We then receive frame 2, with NSSN 0, and store it instead of
releasing it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't plan to have products with 3 antennas in the near
future. All the rest of the code follows the same
assumption as well.
Remove the support for antenna C from rs_toggle_ant.
When trying to toggle from ANT_B, this avoids to go through
ANT_C, discover that it doesn't exist and continue to ANT_A.
In MIMO, this avoids to do ANT_AB -> ANT_BC -> ANT_AC and
back to ANT_AB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After a FW reset on A000 NICs, the driver doesn't
set the seq number when re-allocating the queues.
This in turn leads to a mismatch between the seq
number the driver thinks each frame has, and the
actual seq num given by the HW.
This especially causes issues with aggregations,
since the driver could be waiting to start an
aggregation and queue traffic from the mac80211
until then, when actually it shouldn't be waiting.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the code is mixing defines and is inconsistent.
When enabling a queue, we usually configure the scheduler
with IWL_FRAME_LIMIT - 64.
When sending to firmware the rate scaling, we limit aggregation
to LINK_QUAL_AGG_FRAME_LIMIT_DEF - 63, due to a scheduler bug.
Given that, clean up the following:
- Fix a stray queue enablement with LINK_QUAL_AGG_FRAME_LIMIT_DEF.
- Change the comparison that tests if queue needs to be reconfigured
to be compared directly to how it was configured.
This also saves the redundant round down of the buffer size just
for the sake of comparing it, making the code more readable.
- Better document gen2 logic
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a macro for converting TX response rate to a
rate scale value, use it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In the compressed BA notif, the driver didn't parse out
the LQ color, so statistics for the rates tried were
always thrown out. Add it so it gets correctly used.
While at it, fix the name of the relevant field in the
struct.
Fixes: c46e7724bf ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now have two different minimum valid values for
umac_error_event_table. To avoid hardcoding the minimum value in the
driver, add a value to cfg where it can be read from.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in checking the validity of the
umac_error_event_table pointer every time we generate a dump. It's
cleaner to do so when we read the value, namely when we receive the
alive data.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, UMAC error data reading is restricted to DCCM.
A000 NICs use SMEM for this data.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All callers of iwl_mvm_release_frames() already have the baid_data
pointer, so we don't need to (re)calculate it inside the function.
Just pass it instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The reason station id and tid fields are both in baid data and
in the reorder buffer per queue is that we couldn't access the
baid_data in the reorder timer functions.
Now that we do some pointer math and access it anyway, those
fields can be removed.
This save some space and some code.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we may have up to 256 entries per reorder buffer, and possibly up
to 16 queues, we can use a LOT of memory for this (64k for each station).
Allocate it according to what we need, which is of course much less for HT
stations (only 16k at a max of 16 queues).
However, this comes at the expense of complicating the code a bit to
calculate the right entry structure to use for each frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The default power limit read from the SPLC method in ACPI doesn't
have anything to do with the transport and is only used in the opmode,
so we can remove it from the trans. Additionally, this value is only
user when the opmode is starting, so we don't need to store it
anywhere.
Remove the dflt_pwr_limit element from the trans and move call to
iwl_acpi_get_pwr_limit() call to mvm.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Getting the wrong statistics size is a problem, having a warning
will help us catch it quicker during firmware/driver development.
In released firmware/driver versions, we obviously make sure this
won't happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_get_bios_mcc() function was in the iwl-nvm-parse.c file, but
it has nothing to do with the NVM. Move it to fw/acpi.c and rename it
to iwl_acpi_get_mcc().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move this function to acpi.c, renaming it to iwl_acpi_get_wifi_pkg(),
because it can also be used with other methods (i.e. SPLC and WRDD).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ACPI table size definitions were spread around the different files
that used them. Move them all to a common place.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of defining each method where they are used and re-defining
WIFI_DOMAIN in each one of them, move all the definitions to a central
place and define the domain only a single time.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are many places where the same process of invoking a method from
ACPI is used, causing a lot of duplicate code. To improve this,
introduce a new function to get an ACPI object by invoking an ACPI
method that can be reused.
Additionally, since this function needs to be called when we only have
the trans, the opmode or the device, introduce a new debug macro that
gets the device as a parameter so it can be used in the new function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case there is a FW bug where the BAID value in the
metadata is not properly initialized we hit the warning for
every RX packet.
Change it to warn once and add elaborate message.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have an AP which supports HT and a single HT
station is connected, we change the min_width from
NL80211_CHAN_WIDTH_20_NOHT to NL80211_CHAN_WIDTH_20. This
of course has no implication on the channel width but still
sends a command to the firmware.
Remember the last width that was sent and refrain from
sending unnecessary commands to the firmware.
Sending a PHY_CTXT_CMD to the firmware has a cost since it
recalculates the presence on the medium and because of that
it closes the transmit queues for a short while.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger that collects data when a frame is released
because of the timer of the reordering buffer was not
implemented for 9000 devices.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This was never used by any product. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New quota command adds a field indicating low latency
direction per quota.
A TLV API bit was added to indicate the new API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a dbgfs entry for an easy way during runtime to
check what FW file was loaded, and get some general
FW-related data.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
