The SPI protocol for the QCA7000 doesn't have any fault detection.
In order to increase the drivers reliability in noisy environments,
we could implement a write verification inspired by the enc28j60.
This should avoid situations were the driver wrongly assumes the
receive interrupt is enabled and miss all incoming packets.
This function is disabled per default and can be controlled via module
parameter wr_verify.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows each TXQ to be picked in a round-robin fashion by
the PPv2 transmit scheduling mechanism. This is opposed to the default
behaviour that prioritizes the highest numbered queues.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PPv2 controller has multiple TX queues, we can spread traffic
by assining TX queues to CPUs, allowing to use XPS to balance egress
traffic between CPUs.
Suggested-by : Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
nfp uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx5 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx4 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
i40evf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
This also removes a problematic use of disable_irq() in
a context it is forbidden, as explained in commit
af3e0fcf78 ("8139too: Use disable_irq_nosync() in
rtl8139_poll_controller()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbevf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbe uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, mlxsw tolerated firmware versions that weren't exactly
matching the required version, if the branch number matched. That
allowed the users to test various firmware versions as long as they were
on the right branch.
On the other hand, it made it impossible for mlxsw to put a hard lower
bound on a version that fixes all problems known to date. If a user had
a somewhat older FW version installed, mlxsw would start up just fine,
possibly performing non-optimally as it would use features that trigger
problematic behavior.
Therefore tweak the check to accept any FW version that is:
- on the same branch as the preferred version, and
- the same as or newer than the preferred version.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes hclge_get_port_type which is redundant.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our VF has not implemented the ops for get_port_type. So when we executing
ethtool ethx cmd of VF, hns3_get_link_ksettings will return directly. And
we can not query anything.
To support get_link_ksettings for VF, this patch replaces get_port_type
with get_media_type. If the media type is HNAE3_MEDIA_TYPE_NONE,
hns3_get_link_ksettings will return link information of VF.
Fixes: 12f46bc1d4 ("net: hns3: Refine hns3_get_link_ksettings()")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ops of get_media_type support for VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are already multiple types packets statistics for error packets,
it's unnecessary to print them, which may affect the rx performance if
print too many.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dma_mapping_error is unlikely happened, this patch adds unlikely for
dma_mapping_error check.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When nic down, it firstly calls netif_tx_stop_all_queues(), then calls
napi_disable(). But napi_disable() will wait current napi_poll finish,
it may call netif_tx_wake_queue(). This patch fixes it by add nic state
checking.
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few "switch-case" codes missed handle for default case. For
some abnormal case, it should return error code instead of return 0.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix of most functions for vf are hclgevf. This patch renames the
function with inconsistent prefix.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two tqp_num variables "hdev->tqp_num" and "kinfo->tqp_num"
used in VF. "hdev->tqp_num" is the total tqp number allocated to the
VF, and "kinfo->tqp_num" indicates the tqp number being used by the
VF. Usually the two variables are equal. But for the case hdev->tqp_num
larger than rss_size_max, and num_tc is 1, "kinfo->tqp_num" will be
less than "hdev->tqp_num".
In original codes, "hdev->tqp_num" is always used to traverse the
tqp array of kinfo. It may cause null pointer error when "hdev->tqp_num"
is larger than "kinfo->tqp_num"
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some prefix of tx/rx statistic names are redundant, this patch modifies
these names.
The new prefix looks like below:
rxq#1_ -> rxq1_
txq#1_ -> txq1_
tx_dropped -> dropped
tx_wake -> wake
tx_busy -> busy
rx_dropped -> dropped
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For desc.data is already point to the address of struct member "data[6]",
it's unnecessary to use '&' to get its address. This patch unifies all
the type convert for dest.data, using "req = (struct name *)dest.data".
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a defect in hclge_ets_validate(). If each member of tc_tsa is
not IEEE_8021QAZ_TSA_ETS, the variable total_ets_bw won't be updated.
In this case, the check for value of total_ets_bw will fail. This patch
fixes it by checking total_ets_bw only after it has been updated.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit to ravb had the side effect of making the PHY
advertise Pause and Asym Pause, which previously did not happen. By
default, phydev->supported has both forms of pause enabled, but
phydev->advertising does not. The new phy_remove_link_mode() copies
phydev->supported to phydev->advertising after removing the requested
link mode. These Pause configuration bits appears it stops the PHY
from completing Auto-Neg and the link remains down. Be explicit and
remove the Pause and Asym Pause modes, so restoring the old behavior.
Fixes: 41124fa64d ("net: ethernet: Add helper to remove a supported link mode")
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/net/ethernet/mellanox/mlx4/eq.c:243:11: warning: address of
array 'eq->affinity_mask' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!eq->affinity_mask || cpumask_empty(eq->affinity_mask))
~~~~~^~~~~~~~~~~~~
1 warning generated.
Use cpumask_available, introduced in commit f7e30f01a9 ("cpumask: Add
helper cpumask_available()"), which does the proper checking and avoids
this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/86
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a variable is assigned to itself.
drivers/net/ethernet/brocade/bna/bna_enet.c:1800:9: warning: explicitly
assigning value of variable of type 'int' to itself [-Wself-assign]
for (i = i; i < (bna->ioceth.attr.num_ucmac * 2); i++)
~ ^ ~
drivers/net/ethernet/brocade/bna/bna_enet.c:1835:9: warning: explicitly
assigning value of variable of type 'int' to itself [-Wself-assign]
for (i = i; i < (bna->ioceth.attr.num_mcmac * 2); i++)
~ ^ ~
2 warnings generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/110
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/net/ethernet/neterion/vxge/vxge-traffic.c:2265:31: warning:
equality comparison with extraneous parentheses [-Wparentheses-equality]
if ((hldev->config.intr_mode ==
VXGE_HW_INTR_MODE_MSIX_ONE_SHOT))
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/neterion/vxge/vxge-traffic.c:2265:31: note: remove
extraneous parentheses around the comparison to silence this warning
if ((hldev->config.intr_mode ==
VXGE_HW_INTR_MODE_MSIX_ONE_SHOT))
~ ^ ~
drivers/net/ethernet/neterion/vxge/vxge-traffic.c:2265:31: note: use '='
to turn this equality comparison into an assignment
if ((hldev->config.intr_mode ==
VXGE_HW_INTR_MODE_MSIX_ONE_SHOT))
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/124
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a trailing underscore from the multicast/unicast names.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Provide current link status of VF in ndo_get_vf_config
handler.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a workaround for FW bug -
MFW generates bandwidth attention in single function mode, which
is only expected to be generated in multi function mode.
This undesired attention in SF mode results in incorrect HW
configuration and resulting into Tx timeout.
Signed-off-by: Shahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for `ndo_set_vf_spoofchk' to allow PF control over
its VF spoof-checking configuration.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When extracting frames from the Ocelot switch, the frame check sequence
(FCS) is present at the end of the data extracted. The FCS was put into
the sk buffer which introduced some issues (as length related ones), as
the FCS shouldn't be part of an Rx sk buffer.
This patch fixes the Ocelot switch extraction behaviour by discarding
the FCS.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_skb has taken the null pointer into account. hence it is safe
to remove the redundant null pointer check before kfree_skb.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_skb has taken the null pointer into account. hence it is safe
to remove the redundant null pointer check before kfree_skb.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The continue will not truely skip any code. hence it is safe to
remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The continue will not truely skip any code. hence it is safe to
remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported that chip version 33 (RTL8168E) ends up with
10MBit/Half on a 1GBit link after resuming from S3 (with different
link partners). For whatever reason the PHY on this chip doesn't
properly start a renegotiation when soft-reset.
Explicitly requesting a renegotiation fixes this.
Fixes: a2965f12fd ("r8169: remove rtl8169_set_speed_xmii")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Neil MacLeod <neil@nmacleod.com>
Tested-by: Neil MacLeod <neil@nmacleod.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt offload code currently supports only 'push' and 'pop' operation: let
.ndo_setup_tc() return -EOPNOTSUPP if VLAN 'modify' action is configured.
Fixes: 2ae7408fed ("bnxt_en: bnxt: add TC flower filter offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header ocelot_dev_gmii.h is unused since the inclusion of the driver.
It is unused, lets just remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC-aware mode was introduced to mlxsw in commit 7b81953066 ("mlxsw: spectrum:
Configure MC-aware mode on mlxsw ports") and fixed up later in commit
3a3539cd36 ("mlxsw: spectrum_buffers: Set up a dedicated pool for BUM
traffic"). As the final piece of puzzle, a firmware issue whereby a wrong
priority was assigned to BUM traffic was corrected in FW version 13.1703.4.
Therefore require this FW version in the driver.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBMM register configures shared buffer allocation and settings for
MC packets according to switch priority. The recommended values are no
reserved buffer and alpha of 1/4, which corresponds to buf_max of 6.
Update mlxsw_sp_sb_mms accordingly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pool 15 (indexed as 8) is dedicated to MC traffic. Its configuration has
been kept at default, because the table-based configuration wasn't
expressive enough to allow the explicit configuration.
Now that the configuration of pool 15 can be described, do so. The MC
pool should have infinite size, infinite per-TC quota, and per-port
limit of 90K.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some pools configured through the sb_pm entries may have by default
static size. The MC pool is now not explicitly configured, however it
gets configured as static implicitly by 0-initializing sb->prs, and a
follow-up patch adds an explicit configuration to the same effect.
To support this, pass max_buff taken from sb_pm and sb_cm entries
through cell conversion before handing it to mlxsw_sp_sb_pm_write(), if
the pool that the sb_pm entry configures is statically-sized.
To keep current behavior, update mlxsw_sp_sb_cms_egress[] to denote
buffer sizes in bytes (assuming Spectrum 1 cell sizes, which the
original code assumed as well) instead of cells. Note that a follow-up
patch changes this to infinite size.
Also tweak a comment at SBMM configuration to remain true now that
statically-sized pools exist.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBPM register configures the shared buffer allocation and
configuration per port and pool. The min_buff value is the buffer size
dedicated to this single function, and is configured in cells.
Currently, all sb_pm entries have 0 for min_buff, and therefore the
actual unit is immaterial. However, in a follow-up patch we want to add
entries with non-zero minimum.
Therefore pass the min_buff from the sb_pm table through the cell
conversion before handing it over to mlxsw_sp_sb_pm_write().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBCM register configures the shared buffer configuration according
to port and TC. So far all pools have had a dynamic size, where the
infinite size is easy to express by using max_buff of 0xff. However the
MC pool should be configured with static size, and the infinite size
thus needs to be set using the field SBCM.infi_max.
Therefore add the field infi_max to the SBCM register and to
mlxsw_reg_sbcm_pack(). Extend mlxsw_sp_sb_cm_write() to handle infinite
sizes as well. Report infinite pool limits as if the limit actually were
the total shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC pool should have an infinite size (i.e. no quota).
To that end, add infi_size to the SBPR register and extend
mlxsw_reg_sbpr_pack(). Also add MLXSW_SP_SB_INFI to denote
buffers that should have an infinite size.
Change mlxsw_sp_sb_pr_write() to take as parameter byte size,
instead of cell size, and add the special handling of infinite
buffers. Report pools with infinite size as if they actually
take the full shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Entities of infinite size will be reported as if they had the maximum
size allowed by the chip. To that end, keep track of maximum shared
buffer size in mlxsw_sp->sb.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code assumes that ingress and egress has the same number of
traffic classes. Since the introduction of MC-aware mode that assumption
hasn't held anymore, and there have been 16 TCs on the egress as opposed
to 8 on ingress.
Break the assumption of symmetry by splitting the artifacts related to
shared-buffer TC counting to ingress and egress parts.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw assumes that each ingress pool has its egress
counterpart, and that pool index for purposes of caching matches the
index with which the hardware should be configured. As we want to expose
the MC pool, both of these assumptions break.
Instead, maintain the pool index as long as possible. Unify ingress and
egress caches and use the pool index as cache index as well. Only
translate to FW pool numbering when actually packing the registers. This
simplifies things considerably, as the pool index is the only quantity
necessary to uniquely identify a pool, and the pool/direction split is
not necessary until firmware is talked to.
To support the mapping between pool indices and pool numbers and
directions, which is not neatly mathematical anymore, introduce a pool
descriptor table, indexed by pool index, to facilitate the translation.
Include the MC pool in the descriptor table as well, so that it can be
referenced from mlxsw_sp_sb_cms_egress.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.
By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to configure the DORQ to use vlan-id/priority for
roce EDPM.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain multi-function switch dependent modes, firmware adds vlan tag 0
to the untagged frames. This leads to double tagging for the traffic
if the dcbx is enabled, which is not the desired behavior. To avoid this,
driver needs to set "dcb_dont_add_vlan0" flag.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-function mode, driver receives the stag value (outer vlan)
for a PF from management FW (MFW). If the stag value is negotiated prior to
the driver load, then the stag is not notified to the driver and hence
driver will have the invalid stag value.
The fix is to request the MFW for STAG value during the driver load time.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_set_link_ksettings':
drivers/net/ethernet/atheros/atlx/atl1.c:3280:6: warning:
variable 'advertising' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/e1000/e1000_main.c: In function 'e1000_watchdog':
drivers/net/ethernet/intel/e1000/e1000_main.c:2436:9: warning:
variable 'txb2b' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable 'index_specified' is never used after being assigned.
hence it should be redundant adn can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP supports fairly enormous ring sizes (up to 256k descriptors).
In commit 4662717038 ("nfp: use kvcalloc() to allocate SW buffer
descriptor arrays") we have started using kvcalloc() functions to
make sure the allocation of software state arrays doesn't hit
the MAX_ORDER limit. Unfortunately, we can't use virtual mappings
for the DMA region holding HW descriptors. In case this allocation
fails instead of the generic (and fairly scary) warning/splat in
the logs print a helpful message explaining what happened and
suggesting how to fix it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting register 0x82 to value 01 is done a few lines before for all
chip versions <= 06 anyway. And setting PHY register 0x0b to value 00
is done at the end of rtl8169s_hw_phy_config() already. So we can
remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI_LATENCY_TIMER is ignored on PCIe, therefore we have to do this
for the PCI chips (version <= 06) only. Also we can move setting
PCI_CACHE_LINE_SIZE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That local variable are never used after being assigned.
hence it should be redundant and can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable 'k' is never used after being assigned.
hence it should be redundant adn can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DMA_API_DEBUG enabled we now get a warning when using the
mvneta driver:
mvneta d0030000.ethernet: DMA-API: device driver frees DMA memory with
wrong function [device address=0x000000001165b000] [size=4096 bytes]
[mapped as page] [unmapped as single]
This is because when using the s/w buffer management, the Rx descriptor
buffer is mapped with dma_map_page but unmapped with dma_unmap_single.
This patch fixes this by using the right unmapping function.
Fixes: 562e2f467e ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far all the places calling hclge_tm_q_to_qs_map_cfg() are assigning
an u16 type value to "q_id", and in the processing of
hclge_tm_q_to_qs_map_cfg(), it also converts the "q_id" to le16.
The max tqp number for pf can be more than 256, we should use "u16" to
store the queue id, instead of "u8", which may cause data lost.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When roce is loaded before nic, the roce client will not be initialized
until nic client is initialized, but roce init flag is set before it.
Furthermore, in this case of nic initialized success and roce failed,
the nic init flag is not set, and roce init flag is not cleared.
This patch fixes it by set init flag only after the client is initialized
successfully.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If initialize client failed or finish uninitializing client, we should
clear the client pointer. It may cause unexpected result when use
uninitialized client. Meanwhile, we also should check whether client
exist when uninitialize it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware's description, the head pointer register should
be written before the tail pointer register while initializing the vf
command queue. Otherwise, it may trigger an interrupt even though there
is no command received.
Fixes: fedd0c15d2 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function of genphy_read_status is that reading phy information
from HW and using these information to update SW variable. If user
is using ethtool to setting the speed of phy and service task is calling
by hclge_get_mac_phy_link, the result of speed setting is uncertain.
Because ethtool cmd will modified phydev and hclge_get_mac_phy_link also
will modified phydev.
Because phy state machine will update phy link periodically, we can
just use phydev->link to check the link status. This patch removes
function call of genphy_read_status. To ensure accuracy, this patch
adds a phy state check. If phy state is not PHY_RUNNING, we consider
link is down. Because in some scenarios, phydev->link may be link up,
but phy state is not PHY_RUNNING. This is just an intermediate state.
In fact, the link is not ready yet.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, HW link status is up. If hclge_update_link_status is called
before net up, driver will print "link up". It is not suitable. hdev
state check is needed when getting link status.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We clear STATE_DOWN bit of hdev state when starting net, but do not set
it again when stopping net. It causes that the net is down, but hdev state
is still up. STATE_DOWN bit of hdev state should be set when stopping net.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the .ndo_do_ioctl net_device_ops operation to support
the PHY MII ioctl for PF driver.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All pf have permission to read packet statistics of public in hardware,
but the read operation will clear registers which cause statistical
inaccuracy.
This patch removes all packet statistics of public.
Signed-off-by: Junxin Chen <chenjunxin1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The the actual Tx work is minimal, driver can clean up as more
Tx descriptors as possible in a irq.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds unlikely for buf_num check.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All irq will float to cpu0 if do not set irq affinity.
This patch adds default irq affinity in hns3 driver, users can
also change the irq affinity in OS.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the explicit call to netif_carrier_off() in
mvneta_open() as this is already handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the explicit call to netif_carrier_off() in PPv2's
open() path, as this is now handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the mvpp2_percpu_read/write/... functions aren't really per-cpu but
per s/w thread, rename them to include 'thread' instead of 'percpu'.
This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 network controller has 9 internal threads. The driver
works fine when there are less CPUs available than threads. This isn't
true if more CPUs are available. As this is a valid use case, handle
this particular case.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch maps all uses of the CPU to threads. All this_cpu calls are
replaced, and all smp_processor_id() calls are wrapped into the
indirection.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the Marvell PPv2 driver to stop using directly the
CPU number to access per-thread registers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Marvell PPv2 driver the mvpp2_read_relaxed function is only used
in a single file. Make it static and remove its prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2 driver has per-cpu functions. As they only are used in
the main file, make them static and remove their prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the PPv2 driver so that all CPU variables are unsigned, as it
makes no sense to have a negative CPU number. This patch is cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PPv2.2 engine only has 8 Rx queues per CPU, while PPv2.1 has
16 of them. This patch updates the code so that the Rx queues mask width
is selected given the version of the network controller used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the probing function so that the queue mode isn't
updated while probing, as the driver would silently end up using a
configuration not wanted by the user. The patch adds an extra check to
validate the chosen queue mode instead, and the driver will fail to
probe if the configuration is invalid.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the IRQs in the Marvell PPv2 driver as their current
names match the way they are used in software. But this will change in
the future, and those IRQs have nothing to do with Rx/Tx interrupts
(this can be configured). The new binding also describe more interrupts
as some where left out.
The old binding support is kept for backward compatibility.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the number of s/w threads to 9, its maximum value,
instead of 8. This is not a fix as only 4 of the s/w threads were used
so far, but more could be used in the future.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets from two descriptor to one descriptor because R-Car Gen3
does not have the 4 bytes alignment restriction of the transmission buffer.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.
Fixes: edc660fa09 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module.h already contained moduleparam.h, so it is safe to remove
the redundant include.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace the custom definition of writeq/read and use ones
defined in linux/io-64-nonatomic-lo-hi.h.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replace the custom definition of writeq/read and use ones
defined in linux/io-64-nonatomic-lo-hi.h.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compile warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: nvm_param.dir_type may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, also the implementation in this
driver has returns 'netdev_tx_t' value, so just change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJboCdPAAoJEEg/ir3gV/o+OqQH/2U2kCMUHRuG6WGEbm+bTz7m
fF2L1iRMeXvpmD0FrWs1XiBEg1/6Gf6GfNLmuwRqhHJMi/ok1310V5UbQ3dcXEQ5
7rIzBUbd2jyrI5wln9ISgmvgi/r7Cdzf9xNM3MHmPCouNWxbX85VLTGdTXcsUknd
Z7lZHbPjB8aeZEBmeQdNbGvwZOe9IIgTlfEN4gwrYvUtJD82HrGgGpdLvnSWgy4X
RhKdjvhkYx5ba3AH9CbY88oR5LRjhk3dGhngpMDvQZBmqE0W0j8tXkR8bj36zJN6
m2YJadeGlds7fubFORYaaDGuPBtCT5SnrJqboEMZ8fzuJMqdyvBNI/LtTRTIGAc=
=FOdR
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-09-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-09-17
Sorry about the previous submission of this series which was mistakenly
marked for net-next, here I am resending with 'net' mark.
This series provides three fixes to mlx5 core and mlx5e netdevice
driver.
Please pull and let me know if there's any problem.
For -stable v4.16:
('net/mlx5: Check for SQ and not RQ state when modifying hairpin SQ')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.
According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.
This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: f748be531d ("stmmac: support new GMAC4")
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-09-18
This series contains changes to i40evf so that it becomes a more
generic virtual function driver for current and future silicon.
While doing the rename of i40evf to a more generic name of iavf,
we also put the driver on a severe diet due to how much of the
code was unneeded or was unused. The outcome is a lean and mean
virtual function driver that continues to work on existing 40GbE
(i40e) virtual devices and prepped for future supported devices,
like the 100GbE (ice) virtual devices.
This solves 2 issues we saw coming or were already present, the
first was constant code duplication happening with i40e/i40evf,
when much of the duplicate code in the i40evf was not used or was
not needed. The second was to remove the future confusion of why
future VF devices that were not considered "40GbE" only devices
were supported by i40evf.
The thought is that iavf will be the virtual function driver for
all future devices, so it should have a "generic" name to properly
represent that it is the VF driver for multiple generations of
devices.
The last patch in this series is unreleated to the iavf conversion
and just has to do with a MODULE_LICENSE correction.
Known Caveats:
Existing user space configurations may have to change, but the module
alias in patch 1 helps a bit here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.
Fix the MODULE_LICENSE to be GPL v2, for all our drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This finishes the process of renaming the files that
make sense to rename (skipping adminq related files that
talk to i40e), and fixes up the build and the #includes
so that everything builds nicely.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the big rename patch, it takes most of the i40e_
and I40E_ strings and renames them to iavf_ and IAVF_.
Some of the adminq code, as well as most of the client
interface code used by RDMA is left unchanged in order
to indicate that the driver is talking to non-internal to
iavf code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename the i40e_trace file and fix up all the callers
to the new names inside the iavf_trace.h file.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up the i40e_hw names to new name, including versions
inside other strings.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take care of some renames containing I40E_ADMINQ_DESC.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename the device ID defines to have IAVF in them
and remove all the unused defines.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the register name references to I40E_VF* and change to
IAVF_VF. Update the descriptor names and defines to the IAVF
name.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Simply move the i40evf files to the new name, updating the #includes
to track the new names, and updating the Makefile as well.
A future patch will remove the i40e references (after the code
removal patches later in this series).
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is just a rename of an internal variable i40e_status, but
it was a pretty big change and so deserved it's own patch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This basically begins the internal portion of the rename of i40evf to iavf,
by renaming many of the functions, structs, variables and defines.
Most of the changes were made mechanically, which introduces some
alignment issues.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a bunch of unused code and reformat a few lines. Also
remove some now un-necessary files.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the Intel Ethernet Adaptive Virtual Function driver
(i40evf) to a new name (iavf) that is more consistent with
the ongoing maintenance of the driver as the universal VF driver
for multiple product lines.
This first patch fixes up the directory names and the .ko name,
intentionally ignoring the function names inside the driver
for now. Basically this is the simplest patch that gets
the rename done and will be followed by other patches that
rename the internal functions.
This patch also addresses a couple of string/name issues
and updates the Copyright year.
Also, made sure to add a MODULE_ALIAS to the old name.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.17 are:
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 892:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
[FUNC] usleep_range
drivers/net/ethernet/socionext/sni_ave.c, 888:
usleep_range in ave_rxfifo_reset
drivers/net/ethernet/socionext/sni_ave.c, 932:
ave_rxfifo_reset in ave_irq_handler
To fix these bugs, usleep_range() is replaced with udelay().
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards a platform clock is used as clock for the r8169 chip,
this commit adds support for getting and enabling this clock (assuming
it has an "ether_clk" alias set on it).
This is related to commit d31fd43c0f ("clk: x86: Do not gate clocks
enabled by the firmware") which is a previous attempt to fix this for some
x86 boards, but this causes all Cherry Trail SoC using boards to not reach
there lowest power states when suspending.
This commit (together with an atom-pmc-clk driver commit adding the alias)
fixes things properly by making the r8169 get the clock and enable it when
it needs it.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=193891#c102
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=196861
Cc: Johannes Stezenbach <js@sig21.net>
Cc: Carlo Caione <carlo@endlessm.com>
Reported-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel SoC was prevented from entering lower idle state because
of RTL8106E's ASPM was not enabled.
So enable ASPM on RTL8106E (chip version 39).
Now the Intel SoC can enter lower idle state, power consumption and
temperature are much lower.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a small delay after setting ASPM in vendor drivers, r8101 and
r8168.
In addition, those drivers enable ASPM before ClkReq, also change that
to align with vendor driver.
I haven't seen anything bad becasue of this, but I think it's better to
keep in sync with vendor driver.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When modifying hairpin SQ, instead of checking if the next state equals
to MLX5_SQC_STATE_RDY, we compare it against the MLX5_RQC_STATE_RDY enum
value.
The code worked since both of MLX5_RQC_STATE_RDY and MLX5_SQC_STATE_RDY
have the same value today.
This patch fixes this issue.
Fixes: 18e568c390 ("net/mlx5: Hairpin pair core object setup")
Change-Id: I6758aa7b4bd137966ae28206b70648c5bc223b46
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use accessor function READ_ONCE to read from coherent memory modified
by the device and read by the driver. This becomes most important in
preemptive kernels where cond_resched implementation does not have the
side effect which guaranteed the updated value.
Fixes: 269d26f47f ("net/mlx5: Reduce command polling interval")
Change-Id: Ie6deeb565ffaf76777b07448c7fbcce3510bbb8a
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix the following compile warning:
drivers/net/ethernet/microchip/lan743x_main.c:2964:12: warning: lan743x_pm_suspend defined but not used [-Wunused-function]
static int lan743x_pm_suspend(struct device *dev)
drivers/net/ethernet/microchip/lan743x_main.c:2987:12: warning: lan743x_pm_resume defined but not used [-Wunused-function]
static int lan743x_pm_resume(struct device *dev)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add functions for get_fecparam and set_fecparam.
2. Modify lio_get_link_ksettings to display FEC setting.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch and the MAC are in one IP core and they use the same clock
signal from the clock generation unit.
Currently the clock architecture in the lantiq SoC code does not allow
to easily share the same clocks, this has to be fixed by switching to
the common clock framework.
As a workaround the clock of the switch and MAC should be activated when
the MAC gets probed and only disabled when the MAC gets removed. This
way it is ensured that the clock is always enabled when the switch or
MAC is used. The switch can not be used without the MAC.
This fixes a data bus error when rebooting the system and deactivating
the switch and mac and later accessing some registers in the cleanup
while the clocks are disabled.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c:322:5: warning:
symbol 'hns_gmac_wait_fifo_clean' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e9660 ("bnxt_en: Always forward VF MAC address to the PF.")
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Siwei Liu <loseweigh@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The operation ~(p100_inb(VG_LAN_CFG_1) & HP100_LINK_UP) returns a value
that is always non-zero and hence the wait for the link to drop always
terminates prematurely. Fix this by using a logical not operator instead
of a bitwise complement. This issue has been in the driver since
pre-2.6.12-rc2.
Detected by CoverityScan, CID#114157 ("Logical vs. bitwise operator")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net drivers using phylink shouldn't mess with the link carrier
themselves and should let phylink manage it. The mvpp2 driver wasn't
following this best practice as the mac_config() function made calls to
change the link carrier state. This led to wrongly reported carrier link
state which then triggered other issues. This patch fixes this
behaviour.
But the PPv2 driver relied on this misbehaviour in two cases: for fixed
links and when not using phylink (ACPI mode). The later was fixed by
adding an explicit call to link_up(), which when the ACPI mode will use
phylink should be removed.
The fixed link case was relying on the mac_config() function to set the
link up, as we found an issue in phylink_start() which assumes the
carrier is off. If not, the link_up() function is never called. To fix
this, a call to netif_carrier_off() is added just before phylink_start()
so that we do not introduce a regression in the driver.
Fixes: 4bb0432628 ("net: mvpp2: phylink support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch mades TI_DAVINCI_CPDMA select GENERIC_ALLOCATOR.
without that, the following sparc64 build failure happen
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
(.text+0x278): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit':
(.text+0x340): undefined reference to `gen_pool_alloc'
(.text+0x5c4): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x64c): undefined reference to `gen_pool_free'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.6':
davinci_cpdma.c:(.text+0x17ac): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x17b8): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x1824): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x1830): undefined reference to `gen_pool_avail'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
(.text+0x19f8): undefined reference to `devm_gen_pool_create'
(.text+0x1a90): undefined reference to `gen_pool_add_virt'
Makefile:1011: recipe for target 'vmlinux' failed
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys DWC Ethernet MAC can be configured to have 1..32, 64, or
128 unicast filter entries. (Table 7-8 MAC Address Registers from
databook) Fix dwmac1000_validate_ucast_entries() to accept values
between 1 and 32 in addition.
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- In CXGB4_DCB_STATE_FW_INCOMPLETE state check if the dcb
version is changed and update the dcb supported version.
- Also, fill the priority code point value for priority
based flow control.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
print per rx-queue packet errors in sge_qinfo
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not put host-endian 0 or 1 into big endian feild.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the quest to remove all stack VLA usage from the kernel[1], this
removes the VLA used for the emac xaht registers size. Since the size
of registers can only ever be 4 or 8, as detected in emac_init_config(),
the max can be hardcoded and a runtime test added for robustness.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Ivan Mikhaylov <ivan@de.ibm.com>
Cc: netdev@vger.kernel.org
Co-developed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This drives the PMAC between the GSWIP Switch and the CPU in the VRX200
SoC. This is currently only the very basic version of the Ethernet
driver.
When the DMA channel is activated we receive some packets which were
send to the SoC while it was still in U-Boot, these packets have the
wrong header. Resetting the IP cores did not work so we read out the
extra packets at the beginning and discard them.
This also adapts the clock code in sysctrl.c to use the default name of
the device node so that the driver gets the correct clock. sysctrl.c
should be replaced with a proper common clock driver later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DMA channel is opened the IRQ should not get activated
automatically, this allows it to pull data out manually without the help
of interrupts. This is needed for a workaround in the vrx200 Ethernet
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DIV_ROUND_UP has implemented the code-opened function. Therefore, just
replace the implementation with DIV_ROUND_UP.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_pull_bc_msg':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:907:6: warning:
variable 'fw_mbx' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_issue_bc_post':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:939:16: warning:
variable 'hdr_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers don't indicate they support pause. They expect MAC drivers
to enable its support if the MAC has the needed hardware. Thus MAC
drivers should not mask Pause support, but enable it.
Change a few ANDs to ORs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy supported speed is being used to determine if the MAC should
be configured to 100 or 1G. The masking logic is broken. Instead, look
at 1G supported speeds to enable 1G MAC support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report in standard netdev stats drops and errors as well as
RX multicast from the FW vNIC counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug where ipv6 tunnels would report that it is
getting offloaded to hardware but would actually be rejected
by hardware.
Fixes: b27d6a95a7 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the vlan id field is present when trying
to match a vlan tag. The vlan id and vlan pcp field should be treated
independently.
Fixes: 5571e8c9f2 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After system suspend, sometimes the r8169 doesn't work when ethernet
cable gets pluggued.
This issue happens because rtl_reset_work() doesn't get called from
rtl8169_runtime_resume(), after system suspend.
In rtl_task(), RTL_FLAG_TASK_* only gets cleared if this condition is
met:
if (!netif_running(dev) ||
!test_bit(RTL_FLAG_TASK_ENABLED, tp->wk.flags))
...
If RTL_FLAG_TASK_ENABLED was cleared during system suspend while
RTL_FLAG_TASK_RESET_PENDING was set, the next rtl_schedule_task() won't
schedule task as the flag is still there.
So in addition to clearing RTL_FLAG_TASK_ENABLED, also clears other
flags.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra characters from the names of structures to unify prefixes
used through the driver code (we normally use hw_atl for hw specifics).
HW_ATL_B0_ and HW_ATL_A0_ are the same and useless copies.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed extra spaces, corrected alignment.
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support of Energy-Efficient Ethernet to aQuantia NIC's via ethtool
(according to the IEEE 802.3az specifications)
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add WOL support. Currently only magic packet
(ethtool -s <ethX> wol g) feature is implemented.
Remove hw_set_power and move that to FW_OPS set_power:
because WOL configuration behaves differently on 1x and 2x
firmwares
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added definitions and structures needed to support WOL.
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the upload function, which worked incorrectly with
some chips.
Signed-off-by: Yana Esina <yana.esina@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the changes in patch 1 and 2, droq lock is not required.
So removing droq lock.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed oom task unconditional rescheduling every 250ms and created per
queue oom work queue for refilling buffers.
The oom task refills only if the available descriptors is fallen to 64.
There will be no packets coming in after hitting this level. So NAPI will
not run until oom task refills the buffers.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control packets are processed in tasklet when interface is down and in
NAPI when interface is up. So tasklet can be disabled when interface up
and re-enabled when interface is down.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_zalloc_coherent() now crashes if no dev pointer is given.
Add a dev pointer to the ltq_dma_channel structure and fill it in the
driver using it.
This fixes a bug introduced in kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the incorrect WR_HDR field which can cause a misinterpretation
of ABORT CPL by ULDs, such as iw_cxgb4.
Fixes: a3cdaa69e4 ("cxgb4: Adds CPL support for Shared Receive Queues")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit updated vlan_cmd.dropnovlan_fm but failed to remove
the older assignment. Fix this by removing the former redundant
assignment.
Detected by CoverityScan, CID#1473290 ("Unused value")
Fixes: a89cdd8e7c ("cxgb4: impose mandatory VLAN usage when non-zero TAG ID")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added memory barriers where they were missing to support multiple
architectures, and removed redundant ones.
As part of removing the redundant memory barriers and improving
performance, we moved to more relaxed versions of memory barriers,
as well as to the more relaxed version of writel - writel_relaxed,
while maintaining correctness.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add READ_ONCE calls where necessary (for example when iterating
over a memory field that gets updated by the hardware).
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acquire the rtnl_lock during device destruction to avoid
using partially destroyed device.
ena_remove() shares almost the same logic as ena_destroy_device(),
so use ena_destroy_device() and avoid duplications.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_destroy_device() can potentially be called twice.
To avoid this, check that the device is running and
only then proceed destroying it.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ena_destroy_device() is called from ena_suspend(), the device is
still reachable from the driver. Therefore, the driver can send a command
to the device to free all resources.
However, in all other cases of calling ena_destroy_device(), the device is
potentially in an error state and unreachable from the driver. In these
cases the driver must not send commands to the device.
The current implementation does not request resource freeing from the
device even when possible. We add the graceful parameter to
ena_destroy_device() to enable resource freeing when possible, and
use it in ena_suspend().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer length field in the ena rx descriptor is 16 bit, and the
current driver passes a full page in each ena rx descriptor.
When PAGE_SIZE equals 64kB or more, the buffer length field becomes
zero.
To solve this issue, limit the ena Rx descriptor to use 16kB even
when allocating 64kB kernel pages. This change would not impact ena
device functionality, as 16kB is still larger than maximum MTU.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with driver version 1.5.0, in case of a surprise device
unplug, there is a race caused by invoking ena_destroy_device()
from two different places. As a result, the readless register might
be accessed after it was destroyed.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC >= 4 also supports CBS. Lets enable the TC Ops for these versions.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Essentially reverts commit 8fd75c58a0 ("i40e: move ethtool
stats boiler plate code to i40e_ethtool_stats.h", 2018-08-30), and
additionally moves the similar code in i40evf into i40evf_ethtool.c.
The code was intially moved from i40e_ethtool.c into i40e_ethtool_stats.h
as a way of better logically organizing the code. This has two problems.
First, we can't have an inline function with variadic arguments on all
platforms. Second, it gave the appearance that we had plans to share
code between the i40e and i40evf drivers, due to having a near copy of
the contents in the i40evf/i40e_ethtool_stats.h file.
Patches which actually attempt to combine or share code between the i40e
and i40evf drivers have not materialized, and are likely a ways off.
Rather than fixing the one function which causes build issues, just move
this code back into the i40e_ethtool.c and i40evf_ethtool.c files. Note
that we also change these functions back from static inlines to just
statics, since they're no longer in a header file.
We can revisit this if/when work is done to actually attempt to share
code between drivers. Alternatively, this stats code could be made more
generic so that it can be shared across drivers as part of ethtool
kernel work.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a non-zero VLAN Tag ID is passed to t4_set_vlan_acl()
then impose mandatory VLAN Usage with that VLAN ID.
I.e any other VLAN ID should result in packets getting
dropped.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 488752220b ("liquidio: Add spoof checking on a VF MAC address")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As you are already in a tasklet, it is unnecessary to call spin_lock_bh.
Signed-off-by: jun qian <hangdianqj@163.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3559d81e76 ("r8169: simplify rtl_hw_start_8169") changed order of
two register writes:
1) Caused RxConfig to be written before TX / RX is enabled,
2) Caused TxConfig to be written before TX / RX is enabled.
At least on XIDs 10000000 ("RTL8169sb/8110sb") and
18000000 ("RTL8169sc/8110sc") such writes are ignored by the chip, leaving
values in these registers intact.
Change 1) was reverted by
commit 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices"),
however change 2) wasn't.
In practice, this caused TxConfig's "InterFrameGap time" and "Max DMA Burst
Size per Tx DMA Burst" bits to be zero dramatically reducing TX performance
(in my tests it dropped from around 500Mbps to around 50Mbps).
This patch fixes the issue by moving TxConfig register write a bit later in
the code so it happens after TX / RX is already enabled.
Fixes: 05212ba813 ("r8169: set RxConfig after tx/rx is enabled for RTL8169sb/8110sb devices")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both WARN_ON() and WARN_ONCE() already contain an unlikely(), so it's not
necessary to wrap it into another.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c: In function 'bnxt_tc_parse_flow':
drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c:186:6: warning:
variable 'addr_type' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/cn23xx_vf_device.c: In function 'cn23xx_setup_octeon_vf_device':
drivers/net/ethernet/cavium/liquidio/cn23xx_vf_device.c:619:20: warning:
variable 'ring_flag' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Provide the API to set/unset the spoof checking feature.
2. Add a function to periodically provide the count of found
packets with spoof VF MAC address.
3. Prevent VF MAC address changing while the spoofchk of the VF is
on unless the changing MAC address is issued from PF.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides updates to mlx5 ethernet driver.
1) Starting with a four patches series to optimize flow counters updates,
From Vlad Buslov:
==============================================
By default mlx5 driver updates cached counters each second. Update function
consumes noticeable amount of CPU resources. The goal of this patch series
is to optimize update function.
Investigation revealed following bottlenecks in fs counters
implementation:
1) Update code(scheduled each second) iterates over all counters twice.
(first for finding and deleting counters that are marked for deletion,
second iteration is for actually updating the counters)
2) Counters are stored in rb tree. Linear iteration over all rb tree
elements(rb_next in profiling data) consumed ~65% of time spent in
update function.
Following optimizations were implemented:
1) Instead of just marking counters for deletion, store them in
standalone list. This removes first iteration over whole counters tree.
2) Store counters in sorted list to optimize traversing them and remove
calls to rb_next.
First implementation of these changes caused degradation of performance,
instead of improving it. Investigation revealed that there first cache
line of struct mlx5_fc is full and adding anything to it causes amount
of cache misses to double. To mitigate that, following refactorings were
implemented:
- Change 'addlist' list type from double linked to single linked. This
allowes to get free space for one additional pointer that is used to
store deletion list(optimization 1)
- Substitute rb tree with idr. Idr is non-intrusive data structure and
doesn't require adding any new members to struct mlx5_fc. Use free
space that became available for double linked sorted list that is used
for traversing all counters. (optimization 2)
Described changes reduced CPU time spent in mlx5_fc_stats_work from 70%
to 44%. (global perf profile mode)
============================================
The rest of the series are misc updates:
2) From Kamal, Move mlx5e_priv_flags into en_ethtool.c, to avoid a
compilation warning.
3) From Roi Dayan, Move Q counters allocation and drop RQ to init_rx profile
function to avoid allocating Q counters when not required.
4) From Shay Agroskin, Replace PTP clock lock from RW lock to seq lock.
Almost double the packet rate when timestamping is active on multiple TX
queues.
5) From: Natali Shechtman, set ECN for received packets using CQE indication.
6) From: Alaa Hleihel, don't set CHECKSUM_COMPLETE on SCTP packets.
CHECKSUM_COMPLETE is not applicable to SCTP protocol.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbkKzcAAoJEEg/ir3gV/o+4bsIAKu61DsZZhJAXfwZ4JXI9fN7
iZ9wOPbPovTrkfRfqatcCa3CBwxM1zZ6WzbVTGGieMsUnxjp4G+LAs7m8J+cmWB2
GsxhO3lsF5iGTcEB5Q5a/TlWlUP0CiPcdNZZe6FvT2Vzil+mLAb3BZgIPKPgoyJW
CmDhIOslfolBJC0s4fc+zVcWrShmKnUwHmVLhkOXpz8cfYBB1fBVGebRTZiYsvbf
8CV4buiYx0Fuq9MSnOwaMuPrUP1IB6DweNbFpg9gRd0k4mmWnoNu3l+g1Flgmd88
RtU4+5PEtZF2kNhH/LeiHRqkZ5f2cmOsIKbDZoX6xwzfYesws8jlDJpL5dIhxZA=
=nxDw
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-09-05
This series provides updates to mlx5 ethernet driver.
1) Starting with a four patches series to optimize flow counters updates,
From Vlad Buslov:
==============================================
By default mlx5 driver updates cached counters each second. Update function
consumes noticeable amount of CPU resources. The goal of this patch series
is to optimize update function.
Investigation revealed following bottlenecks in fs counters
implementation:
1) Update code(scheduled each second) iterates over all counters twice.
(first for finding and deleting counters that are marked for deletion,
second iteration is for actually updating the counters)
2) Counters are stored in rb tree. Linear iteration over all rb tree
elements(rb_next in profiling data) consumed ~65% of time spent in
update function.
Following optimizations were implemented:
1) Instead of just marking counters for deletion, store them in
standalone list. This removes first iteration over whole counters tree.
2) Store counters in sorted list to optimize traversing them and remove
calls to rb_next.
First implementation of these changes caused degradation of performance,
instead of improving it. Investigation revealed that there first cache
line of struct mlx5_fc is full and adding anything to it causes amount
of cache misses to double. To mitigate that, following refactorings were
implemented:
- Change 'addlist' list type from double linked to single linked. This
allowes to get free space for one additional pointer that is used to
store deletion list(optimization 1)
- Substitute rb tree with idr. Idr is non-intrusive data structure and
doesn't require adding any new members to struct mlx5_fc. Use free
space that became available for double linked sorted list that is used
for traversing all counters. (optimization 2)
Described changes reduced CPU time spent in mlx5_fc_stats_work from 70%
to 44%. (global perf profile mode)
============================================
The rest of the series are misc updates:
2) From Kamal, Move mlx5e_priv_flags into en_ethtool.c, to avoid a
compilation warning.
3) From Roi Dayan, Move Q counters allocation and drop RQ to init_rx profile
function to avoid allocating Q counters when not required.
4) From Shay Agroskin, Replace PTP clock lock from RW lock to seq lock.
Almost double the packet rate when timestamping is active on multiple TX
queues.
5) From: Natali Shechtman, set ECN for received packets using CQE indication.
6) From: Alaa Hleihel, don't set CHECKSUM_COMPLETE on SCTP packets.
CHECKSUM_COMPLETE is not applicable to SCTP protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN and GRE FW features have to currently be both advertised
for the driver to enable them. Separate the handling.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the accesses to rtsyms now all going via special helpers
we can easily make sure the driver is not reading past the
end of the symbol.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ease of debug preface all error messages with the name
of the symbol which caused them. Use the same message format
for existing messages while at it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return the error and report value through the output param.
Fixes: 640917dd81 ("nfp: support access to absolute RTsyms")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHECKSUM_COMPLETE is not applicable to SCTP protocol.
Setting it for SCTP packets leads to CRC32c validation failure.
Fixes: bbceefce9a ("net/mlx5e: Support RX CHECKSUM_COMPLETE")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In multi-host (MH) NIC scheme, a single HW port serves multiple hosts
or sockets on the same host.
The HW uses a mechanism in the PCIe buffer which monitors
the amount of consumed PCIe buffers per host.
On a certain configuration, under congestion,
the HW emulates a switch doing ECN marking on packets using ECN
indication on the completion descriptor (CQE).
The driver needs to set the ECN bits on the packet SKB,
such that the network stack can react on that, this commit does that.
Signed-off-by: Natali Shechtman <natali@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Changed "priv.clock.lock" lock from 'rw_lock' to 'seq_lock'
in order to improve packet rate performance.
Tested on Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz.
Sent 64b packets between two peers connected by ConnectX-5,
and measured packet rate for the receiver in three modes:
no time-stamping (base rate)
time-stamping using rw_lock (old lock) for critical region
time-stamping using seq_lock (new lock) for critical region
Only the receiver time stamped its packets.
The measured packet rate improvements are:
Single flow (multiple TX rings to single RX ring):
without timestamping: 4.26 (M packets)/sec
with rw-lock (old lock): 4.1 (M packets)/sec
with seq-lock (new lock): 4.16 (M packets)/sec
1.46% improvement
Multiple flows (multiple TX rings to six RX rings):
without timestamping: 22 (M packets)/sec
with rw-lock (old lock): 11.7 (M packets)/sec
with seq-lock (new lock): 21.3 (M packets)/sec
82.05% improvement
The packet rate improvement is due to the lack of atomic operations
for the 'readers' by the seq-lock.
Since there are much more 'readers' than 'writers' contention
on this lock, almost all atomic operations are saved.
this results in a dramatic decrease in overall
cache misses.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Not all profiles query the HW Q counters in update_stats() callback.
HW Q couners are limited per device and in case of representors all
their Q counters are allocated on the parent PF device.
Avoid reundant allocation of HW Q counters by moving the allocation
to init_rx profile callback.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move the definition of mlx5e_priv_flags into en_ethtool.c because it's
only used there.
Fixes: 4e59e28881 ("net/mlx5e: Introduce net device priv flags infrastructure")
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previous patch in series changed flow counter storage structure from
rb_tree to linked list in order to improve flow counter traversal
performance. The drawback of such solution is that flow counter lookup by
id becomes linear in complexity.
Store pointers to flow counters in idr in order to improve lookup
performance to logarithmic again. Idr is non-intrusive data structure and
doesn't require extending flow counter struct with new elements. This means
that idr can be used for lookup, while linked list from previous patch is
used for traversal, and struct mlx5_fc size is <= 2 cache lines.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to improve performance of flow counter stats query loop that
traverses all configured flow counters, replace rb_tree with double-linked
list. This change improves performance of traversing flow counters by
removing the tree traversal. (profiling data showed that call to rb_next
was most top CPU consumer)
However, lookup of flow flow counter in list becomes linear, instead of
logarithmic. This problem is fixed by next patch in series, which adds idr
for fast lookup. Idr is to be used because it is not an intrusive data
structure and doesn't require adding any new members to struct mlx5_fc,
which allows its control data part to stay <= 1 cache line in size.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to prevent flow counters stats work function from traversing whole
flow counters tree while searching for deleted flow counters, new list to
store deleted flow counters is added to struct mlx5_fc_stats. Lockless
NULL-terminated single linked list data type is used due to following
reasons:
- This use case only needs to add single element to list and
remove/iterate whole list. Lockless list doesn't require any additional
synchronization for these operations.
- First cache line of flow counter data structure only has space to store
single additional pointer, which precludes usage of double linked list.
Remove flow counter 'deleted' flag that is no longer needed.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to prevent flow counters stats work function from traversing whole
flow counters tree while searching for deleted flow counters, new list to
store deleted flow counters will be added to struct mlx5_fc_stats. However,
the flow counter structure itself has no space left to store any more data
in first cache line. To free space that is needed to store additional list
node, convert current addlist double linked list (two pointers per node) to
atomic single linked list (one pointer per node).
Lockless NULL-terminated single linked list data type doesn't require any
additional external synchronization for operations used by flow counters
module (add single new element, remove all elements from list and traverse
them). Remove addlist_lock that is no longer needed.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is a false positive report due to incorrect nested lock
annotations as we lock multiple fgs with the same subclass.
Instead of locking all fgs only lock the one being used as was
done before.
Fixes: bd71b08ec2 ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Copy and paste bug was introduced in the offending patch.
We need to write udp source port value into the headers value and not
headers criteria "mask".
Fixes: 142644f8a1 ("net/mlx5e: Ethtool steering flow parsing refactoring")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)
Fixes: 737a234bb6 ("net/mlx5: Introduce attach/detach to interface API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The PCI BDF is not unique. PCI domain must also be considered when
searching for the next physical device during lag setup. Example below:
mlx5_core 0000:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0000:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If building match list fg fails and we never jumped to
search_again_locked label then the function returned without
unlocking the read lock.
Fixes: bd71b08ec2 ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The memory allocated for the slow path table flow group input structure
was not freed upon successful return, fix that.
Fixes: 1967ce6ea5 ("net/mlx5: E-Switch, Refactor fast path FDB table creation in switchdev mode")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: d7037ad73d ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: 388ca8be00 ("IB/mlx5: Implement fragmented completion queue (CQ)")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).
The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.
Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.
Fixes: 59211bd3b6 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With performance optimization the spi transfer and messages of basic
register operations like qcaspi_read_register moved into the private
driver structure. But they weren't protected against mutual access
(e.g. between driver kthread and ethtool). So dumping the QCA7000
registers via ethtool during network traffic could make spi_sync
hang forever, because the completion in spi_message is overwritten.
So revert the optimization completely.
Fixes: 291ab06ecf ("net: qualcomm: new Ethernet over SPI driver for QCA700")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/microchip/lan743x_ptp.c:980:6: warning:
symbol 'lan743x_ptp_set_sync_ts_insert' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/ipoib/ipoib.c:119:6: warning:
symbol 'mlx5i_grp_sw_update_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC-aware mode was recently enabled by mlxsw on Spectrum switches in
commit 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw
ports"). Unfortunately, testing has shown that the fix is incomplete and
in the presented form actually makes the problem even worse, because any
amount of MC traffic causes UC disruption.
The reason for this is that currently, mlxsw configures the MC-specific
TCs (8..15) to map to pool 0. It also configures a maximum buffer size
of 0, but for MC traffic that maximum is disregarded and not part of the
quota. Therefore MC traffic is always admitted to the egress buffer.
Fix the configuration by directing the MC TCs into pool 15, which is
dedicated to MC traffic and recognized as such by the silicon.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow for the RDMA side to allocate packet reformat context.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Currently we attach packet reformat actions only to the FDB namespace.
In preparation to be able to use that for NIC steering, pass the actual
namespace as a parameter.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Renames all encap mlx5_{core,ib} code to use the new naming of packet
reformat. This change doesn't introduce any function change and is
needed to properly reflect the operation being done by this action.
For example not only can we encapsulate a packet, but also decapsulate it.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Those bits are hardware specification and should be defined in the
IFC header file.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Today we are able to attach encap and decap actions only to the FDB. In
preparation to enable those actions on the NIC flow tables, break the
single flag into two. Those flags control whatever a decap or encap
operations can be attached to the flow table created. For FDB, if
encapsulation is required, we set both of them.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
There are RX and TX flow steering namespaces with different number of
actions. Initialize them accordingly.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Those functions will be used by the RDMA side to create modify header
actions to be attached to flow steering rules via verbs.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Extend the ability to add steering rules to NIC TX flow tables.
For now, we are only adding TX bypass (egress) which is used by the RDMA
side. This will allow to shape outgoing traffic and tweak it if needed, for
example performing encapsulation or rewriting headers.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Refactor the switch logic so it's simpler to follow and understand.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Correct the formula for calculating the RQ page remainder,
which should be in byte granularity. The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.
Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.
Fixes: d7037ad73d ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the alloc/dealloc memic FW command opcodes to
avoid "unknown command" prints in the command string
converter and internal error status handler.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Collect descriptors of all ULD and LLD hardware queues managed
by LLD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in ndo_set_vf_rate() when max_tx_rate is 0 disable tx
rate limiting for that vf.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implement, the query operation for fibre port and copper
port are mixed. This patch refines it by seperating them based on the port
type.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the advertised flow control ability has been fetched using
phy_ethtool_ksettings_get() or hclge_get_link_mode() then it is
unnecessary to fetch them again later using hclge_get_flowctrl_adv().
This patch removes it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the dst mac addr of loopback packet is the same as
the host' mac addr, the SSU component may loop back the packet
to host before the packet reaches mac or serdes, which will defect
the purpose of mac or serdes selftest.
This patch changes it by adding 0x1f to the last byte of dst mac
addr.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only fiber port checks if it is necessay to set the
mac through firmware when link is changed, this patch unify the
checking to allow the copper port do the checking too.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev is down, the stack will delete the vlan from
hardware including vlan0, which will cause problem when
doing loopback selftest when netdev is down.
This patch fixes it by always preserving vlan 0 in hardware,
because vlan 0 is defalut vlan, which should always be in
hardware.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ping is runnig and user executes the loopback selftest, the
ping cmd will stop and exit.
This patch fixes it by using the hns3_nic_net_open/stop to offline
the netdev when doing loopback selftest.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tqp and mac need to be enabled when doing loopback selftest,
ae_algo->ops->start/stop is used to do the job, there is a
time window between ae_algo->ops->start/stop and loopback setup,
which will cause selftest failed problem when there is frame
coming in during that time window.
This patch fixes it by enabling the tqp and mac during loopback
setup process.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements shutdown ops in hns3 pci driver, which
unloads the hns3 driver and set the power state to D3hot.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF uses hdev->vlan_table to manage the port vlan table. In function
hclge_set_vlan_filter_hw(), it checks whether a vlan id has been used,
by foreach all the vport bits. It should use macro HCLGE_VPORT_NUM,
not VLAN_N_VID as the foreach condition.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the lower 24 bits of the IPV6 link-local addresses at both
ends are the same, the multicast MAC address for Neigbour Discovery
is the same. The multicast for Neigbour Discovery will fail.
This patch fixes it by including the bonding uplink port in the
multicast group.
Fixes: 46a3df9f9718("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only 128 entries in vf vlan table, if user has added
more than 128 vlan, fw will ignore it and disable the vf vlan
table. So when user deletes the vlan entry that has not been
set to vf vlan table, fw will return not found result and driver
treat that as error, which will cause vlan delete failed problem.
This patch fixes it by returning ok when fw returns not found
result.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea5 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused bnxt_subtract_ulp_resources(). Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0. This will properly setup the
init sequence to initialize the default rings again. We also need
to signal the RDMA driver to stop and clear its interrupts. We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.
Fixes: 25e1acd6b9 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1
by copy-paste mistake for emac4syn.
Fixes: 45d6e54550 ("net/ibm/emac: add 8192 rx/tx fifo size")
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pradeep Nalla <pradeep.nalla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This card identifies itself as:
Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]
Adding a new entry to rtl8169_pci_tbl makes the card work.
Link: http://launchpad.net/bugs/1788730
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the RQs are shared between all pkey interfaces, the stats
should be taken from where the per-ring stats are stored instead
of the parent RQ.
Fixes: 4c6c615e3f ("net/mlx5e: IPoIB, Add PKEY child interface nic profile")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose RX and TX counters by implementing ndo_get_stats64 operation
for child devices.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose RX and TX counters by implementing ndo_get_stats64 operation for
both parent devices.
After this change, all the relevant statistics can be retrieved using
ifconfig.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhanced ipoib does not initialize max_opened_tc causing wrong ethtool
statistics. As mlx5e_grp_sw_update_stats relies on this variable, without
this change, the TX statistics will not be updated.
Fixes: 05909babce ("net/mlx5e: Avoid reset netdev stats on configuration changes")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Kconfig warning with OF_MDIO where OF_MDIO was
selected unconditionally instead of only when
OF is actually enabled.
Fixes 7e8d5755be ("net: nixge: Add support for 64-bit platforms")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel module may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task
To fix this bug, usleep_range() is replaced with udelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the loop of mvneta_tx_done_gbe(), we call the smp_processor_id()
each time, move the call out of the loop to optimize the code a bit.
Before the patch, the loop looks like(under arm64):
ldr x1, [x29,#120]
...
ldr w24, [x1,#36]
...
bl 0 <_raw_spin_lock>
str w24, [x27,#132]
...
After the patch, the loop looks like(under arm64):
...
bl 0 <_raw_spin_lock>
str w23, [x28,#132]
...
where w23 is loaded so be ready before the loop.
>From another side, mvneta_tx_done_gbe() is called from mvneta_poll()
which is in non-preemptible context, so it's safe to call the
smp_processor_id() function once.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code and HW supports NETIF_F_RXCSUM, so let's enable it by default.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_gro_receive() checks NETIF_F_GRO bit as well, if the bit is not
set, we will go through GRO_NORMAL in napi_skb_finish(), so fall back
to netif_receive_skb_internal(), so we don't need to check NETIF_F_GRO
ourself.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw-phy-sel device is not a child of the cpsw interconnect target
module. It lives in the system control module.
Let's fix this issue by trying to use cpsw-phy-sel phandle first if it
exists and if not fall back to current usage of trying to find the
cpsw-phy-sel child. That way the phy sel driver can be a child of the
system control module where it belongs in the device tree.
Without this fix, we cannot have a proper interconnect target module
hierarchy in device tree for things like genpd.
Note that deferred probe is mostly not supported by cpsw and this patch
does not attempt to fix that. In case deferred probe support is needed,
this could be added to cpsw_slave_open() and phy_connect() so they start
handling and returning errors.
For documenting it, looks like the cpsw-phy-sel is used for all cpsw device
tree nodes. It's missing the related binding documentation, so let's also
update the binding documentation accordingly.
Cc: devicetree@vger.kernel.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bgmac.c: In function 'bgmac_dma_alloc':
drivers/net/ethernet/broadcom/bgmac.c:619:6: warning:
variable 'err' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/request_manager.c: In function 'lio_process_iq_request_list':
drivers/net/ethernet/cavium/liquidio/request_manager.c:383:27: warning:
variable 'irh' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver displays an error message for each unrecognized dcbx TLV that's
received from the peer or configured on the device. It is observed that
syslog will be flooded with such messages in certain scenarios e.g.,
frequent link-flaps/lldp-transactions. Changing the severity of this
message to verbose level as it's not an error scenario/message.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c: In function 'bnxt_vf_rep_rx':
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c:212:28: warning:
variable 'rx_stats' set but not used [-Wunused-but-set-variable]
struct bnxt_vf_rep_stats *rx_stats;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC2 uses the same CBS mechanism as GMAC5, only registers offset
changes. Lets use the same TC callbacks and implement the .config_cbs
callback in XGMAC2 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA2 Ethernet driver supports Freescale/NXP SoCs with DPAA2
(DataPath Acceleration Architecture v2). The driver manages
network objects discovered on the fsl-mc bus.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return codes of these functions and halt reset
in case of failure. The driver will remain in a dormant state
until the next reset event, when device initialization will be
re-attempted.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid leaking a running timer we need to wait for the
posted reconfigs after netdev is unregistered. In common
case the process of deinitializing the device will perform
synchronous reconfigs which wait for posted requests, but
especially with VXLAN ports being actively added and removed
there can be a race condition leaving a timer running after
adapter structure is freed leading to a crash.
Add an explicit flush after deregistering and for a good
measure a warning to check if timer is running just before
structures are freed.
Fixes: 3d780b926a ("nfp: add async reconfiguration mechanism")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-09-01
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add AF_XDP zero-copy support for i40e driver (!), from Björn and Magnus.
2) BPF verifier improvements by giving each register its own liveness
chain which allows to simplify and getting rid of skip_callee() logic,
from Edward.
3) Add bpf fs pretty print support for percpu arraymap, percpu hashmap
and percpu lru hashmap. Also add generic percpu formatted print on
bpftool so the same can be dumped there, from Yonghong.
4) Add bpf_{set,get}sockopt() helper support for TCP_SAVE_SYN and
TCP_SAVED_SYN options to allow reflection of tos/tclass from received
SYN packet, from Nikita.
5) Misc improvements to the BPF sockmap test cases in terms of cgroup v2
interaction and removal of incorrect shutdown() calls, from John.
6) Few cleanups in xdp_umem_assign_dev() and xdpsock samples, from Prashant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit gets rid of the structure xdp_umem_props. It was there to
be able to break a dependency at one point, but this is no longer
needed. The values in the struct are instead stored directly in the
xdp_umem structure. This simplifies the xsk code as well as af_xdp
zero-copy drivers and as a bonus gets rid of one internal header file.
The i40e driver is also adapted to the new interface in this commit.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
With certain gcc versions, it was possible to get the warning
"'tx_desc' may be used uninitialized in this function" for the
i40e_xmit_zc. This was not possible, however this commit simplifies
the code path so that this warning is no longer emitted.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
To prevent VF from deleting MAC address that was assigned by the
PF we need to check for that scenario when we try to delete a MAC
address from a VF.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a VF is being removed, there is no need to continue with the
workqueue sync for the adminq task, thus cancel it. Without this call,
when VFs are created and removed right away, there might be a chance for
the driver to crash with events stuck in the adminq.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hold the rtnl lock when we're clearing interrupt scheme
in i40e_shutdown and in i40e_remove.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With current implementation of i40evf_set_features when user sets
any offload via ethtool we set I40EVF_FLAG_AQ_ENABLE_VLAN_STRIPPING
as a required aq which triggers driver to call
i40evf_enable_vlan_stripping. This shouldn't take place.
This patches fixes it by setting the flag only when VLAN offload
is turned on.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If our card has been put in an unstable state due to
other drivers interacting with it, speed settings
might be incorrect. If incorrect, forcefully reset them
on open to known default values.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP is enabled, the driver will report incorrect
statistics. Received frames will reported as transmitted frames.
This commits fixes the i40e implementation of ndo_get_stats64 (struct
net_device_ops), so that iproute2 will report correct statistics
(e.g. when running "ip -stats link show dev eth0") even when XDP is
enabled.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Fixes: 74608d17fe ("i40e: add support for XDP_TX action")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis tools report a problem from original driver submission.
Removing unnecessary check in condition.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set IFF_UNICAST_FLT flag for the VF to prevent it from entering
promiscuous mode when macvlan is added to the VF.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Caught by GCC 8. When we provide a length for strncpy, we should not
include the terminating null. So we must tell it one less than the size
of the destination buffer.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A PF can send any number of queues to the VF and the VF may not
be able to support that many. Check to see that the number of
queues is less than or equal to the max number of queues the
VF can have.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add possibility to change a VF mac address from host side
without reloading the VF driver on the guest side. Without
this patch it is not possible to change the VF mac because
executing i40evf_virtchnl_completion function with
VIRTCHNL_OP_GET_VF_RESOURCES opcode resets the VF mac
address to previous value.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug in the way we handled VF queues, by always showing stats for
the maximum number of queues, even if they aren't allocated. It is not
safe to change the number of strings reported to ethtool, as grabbing
statistics occurs over multiple ethtool ops for which the rtnl_lock()
cannot be held the entire time.
Avoid this by always reporting queue stats for the maximum number of
queues in the netdevice. Share some of the helper functionality for
adding stats with the PF code in i40e_ethtool_stats.h
This should reduce the chance of potential future bugs, and make adding
new statistics easier.
Note for the queue stats, unlike the PF driver we do not keep an array
of queue pointers, but an array of queues, so care must be taken to
avoid accessing queue memory that hasn't yet been allocated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the boiler plate structures and helper functions we recently
added into their own header file, so that the complete collection is
located together.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use an i40e_stats array to handle the queue stats, instead of coding
similar functionality separately. Because of how the queue stats are
accessed on some kernels, we can't easily use i40e_add_ethtool_stats.
Instead, implement a separate helper, i40e_add_queue_stats, which we'll
use instead. This helper will correctly implement the
u64_stats_fetch_begin_irq logic and allow retries until successful. We
share the most complex code by re-using i40e_add_one_ethtool_stat.
This logic additionally easily supports skipping disabled rings by using
a ternary operator before calling the u64_stats_fetch_begin_irq()
function, so that we correctly zero-out the stats values without having
to perform two separate sections of code.
This significantly reduces the boiler plate code in
i40e_get_ethtool_stats, and helps keep the complex logic contained to as
few functions as possible.
With this patch, we've finally converted all the statistics to use the
helpers and the i40e_stats function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Without a valid of_node in struct device we can't find the mvpp2 port
device by its DT node. Specifically, this breaks
of_find_net_device_by_node().
For example, the Armada 8040 based Clearfog GT-8K uses Marvell 88E6141
switch connected to the &cp1_eth2 port:
&cp1_mdio {
...
switch0: switch0@4 {
compatible = "marvell,mv88e6085";
...
ports {
...
port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp1_eth2>;
};
};
};
};
Without this patch, dsa_register_switch() returns -EPROBE_DEFER because
of_find_net_device_by_node() can't find the device_node of the &cp1_eth2
device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove unused functions and data structures.
2. Change the sending of the remaining soft commands to synchronous.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Change struct octnic_ctrl_pkt to support synchronous operation.
2. Change code which use structure octnic_ctrl_pkt to send sc's
synchronously.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add wait_for_sc_completion_timeout() for waiting the response and
handling common response errors
2. Send sc's synchronously: remove unused callback function,
and context structure; use wait_for_sc_completion_timeout() to wait
its response.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Set LIO_SC_MAX_TMO_MS as the maximum timeout value for a soft command
(sc). All sc's use this value as a hard timeout value. Add expiry_time
in struct octeon_soft_command to keep the hard timeout value. The field
wait_time and timeout in struct octeon_soft_command will be obsoleted in
the last patch of this patch series.
2. Add processing a synchronous sc in sc response thread
lio_process_ordered_list. The memory allocated for a synchronous sc will
be freed by lio_process_ordered_list() to the sc pool.
3. Add two response lists for lio_process_ordered_list to process the
storage allocated for sc's:
OCTEON_DONE_SC_LIST response list keeps all sc's which will be freed to
the pool after their requestors have finished processing the responses.
OCTEON_ZOMBIE_SC_LIST response list keeps all sc's which have got
LIO_SC_MAX_TMO_MS timeout.
When an sc gets a hard timeout, lio_process_order_list() will recheck
its status 1 ms later. If the status has not updated by the firmware at
that time, the sc will be removed from OCTEON_DONE_SC_LIST response list
to OCTEON_ZOMBIE_SC_LIST response list. The sc's in the
OCTEON_ZOMBIE_SC_LIST response list will be freed when the driver is
unloaded.
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 64-bit platforms to driver.
The hardware only supports 32-bit register accesses
so the accesses need to be split up into two writes
when setting the current and tail descriptor values.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the fixed PHY with GENET (e.g. MOCA) the PHY link
status can be determined from the internal link status captured
by the MAC. This allows the PHY state machine to use the correct
link state with the fixed PHY even if MAC link event interrupts
are missed when the net device is opened.
Fixes: 8d88c6ebb3 ("net: bcmgenet: enable MoCA link state change detection")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In lio_enable_irq, the pkt_in_done count register was being cleared to
zero. However, there could be some completed instructions which were not
yet processed due to budget and limit constraints.
So, only write this register with the number of actual completions
that were processed.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last in-tree driver using the old {get,set}_settings API.
Note: this is only build tested. I don't have the hardware at hand; as it's
10Mb/s half duplex device and driver can be built only for one subplatform
of 32-bit ARM (Acorn RiscPC), it may be difficult to find someone who does.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Nelson Chang <nelson.chang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Stratix10 SoC is an AARCH64 based platform that shares the same ethernet
controller that is on other SoCFPGA platforms. Build the platform driver.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the R7S9210 which is part of the RZ/A2 series.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds netif_carrier_off before change speed and
duplex in ethtool_ops.set_link_ksettings, and adds
netif_carrier_on after complete the change.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are packets in hardware when changing the speed
or duplex, it may cause hardware hang up.
This patch adds the code for waiting chip to clean the all
pkts(TX & RX) in chip when the driver uses the function named
"adjust link".
This patch cleans the pkts as follows:
1) close rx of chip, close tx of protocol stack.
2) wait rcb, ppe, mac to clean.
3) adjust link
4) open rx of chip, open tx of protocol stack.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I have two Ethernet adapters:
r8169 0000:03:01.0 eth0: RTL8169sb/8110sb, 00:14:d1:14:2d:49, XID 10000000, IRQ 18
r8169 0000:01:00.0 eth0: RTL8168e/8111e, 64:66:b3:11:14:5d, XID 2c200000, IRQ 30
And after upgrading from linux 4.15 [1] to linux 4.18+ [2] RTL8169sb failed to
receive any packets. tcpdump shows a lot of checksum mismatch.
[1]: a0f79386a4
[2]: 0519359784 (4.19 merge window opened)
I started bisecting and the found that [3] breaks it. According to [4]:
"For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled."
So I moved rtl_init_rxcfg() after enabling tx/rs and now my adapter works
(RTL8168e works too).
[3]: 3559d81e76
[4]: e542a2269f ("r8169: adjust the RxConfig
settings.")
Also drop "rx" from rtl_set_rx_tx_config_registers(), since it does nothing
with it already.
Fixes: 3559d81e76 ("r8169: simplify
rtl_hw_start_8169")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Azat Khuzhin <a3at.mail@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4ae0169fd1.
This change in the handling of the coalesce timer is causing regression on
(at least) amlogic platforms.
Network will break down very quickly (a few seconds) after starting
a download. This can easily be reproduced using iperf3 for example.
The problem has been reported on the S805, S905, S912 and A113 SoCs
(Realtek and Micrel PHYs) and it is likely impacting all Amlogics
platforms using Gbit ethernet
No problem was seen with the platform using 10/100 only PHYs (GXL internal)
Reverting change brings things back to normal and allows to use network
again until we better understand the problem with the coalesce timer.
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds zero-copy Tx support for AF_XDP sockets. It implements
the ndo_xsk_async_xmit netdev ndo and performs all the Tx logic from a
NAPI context. This means pulling egress packets from the Tx ring,
placing the frames on the NIC HW descriptor ring and completing sent
frames back to the application via the completion ring.
The regular XDP Tx ring is used for AF_XDP as well. This rationale for
this is as follows: XDP_REDIRECT guarantees mutual exclusion between
different NAPI contexts based on CPU id. In other words, a netdev can
XDP_REDIRECT to another netdev with a different NAPI context, since
the operation is bound to a specific core and each core has its own
hardware ring.
As the AF_XDP Tx action is running in the same NAPI context and using
the same ring, it will also be protected from XDP_REDIRECT actions
with the exact same mechanism.
As with AF_XDP Rx, all AF_XDP Tx specific functions are added to
i40e_xsk.c.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch prepares for the upcoming zero-copy Tx functionality, by
moving common functions and refactor chunks of code into re-usable
functions, used both by the regular path and zero-copy path.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds zero-copy Rx support for AF_XDP sockets. Instead of
allocating buffers of type MEM_TYPE_PAGE_SHARED, the Rx frames are
allocated as MEM_TYPE_ZERO_COPY when AF_XDP is enabled for a certain
queue.
All AF_XDP specific functions are added to a new file, i40e_xsk.c.
Note that when AF_XDP zero-copy is enabled, the XDP action XDP_PASS
will allocate a new buffer and copy the zero-copy frame prior passing
it to the kernel stack.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch prepares for the upcoming zero-copy Rx functionality, by
moving/changing linkage of common functions, used both by the regular
path and zero-copy path.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In this commit, the Rx path is refactored some, as a step torwards the
introduction AF_XDP Rx zero-copy.
The page re-use counter is moved into the i40e_reuse_rx_page, instead
of bumping the counter in many places. The Rx buffer page clearing is
moved for better readability. Lastely, functions to update statistics
and bump the XDP Tx ring are introduced.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add functions for queue pair enable/disable. Instead of resetting the
whole device, only the affected queue pair is disabled or enabled.
This plumbing is used in a later commit, when zero-copy AF_XDP support
is introduced.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Make the RTsym users access the size via the helper, which
takes care of special handling of absolute symbols.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support in nfpcore for reading the absolute RTsyms.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all users of RTsym to the new set of helpers which
handle all targets correctly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make nfp_rtsym_{read,write}_le() and nfp_rtsym_map() use the new
target resolution helpers to allow accessing in-cache symbols.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align nfp_cpp_map_area() with other CPP-level APIs and pass
encoded cpp_id/dest rather than target, action, domain tuple.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTsyms may have special encodings for more complex symbol types.
For example symbols which are placed in external memory unit's
cache directly, constants or local memory. Add set of helpers
which will check for those special encodings and handle them
correctly.
For now only add direct cache accesses, we don't have a need to
access the other ones in foreseeable future.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add error prints to CPP target encoding/decoding logic, otherwise
it's quite hard to pin point the reasons why read or write
operations fail.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon need the MU locality field offset much more
often than just for decoding MIP address. Save it in nfp_cpp
for quick access. Note that we can already reuse the target
config from nfp_cpp, no need to do the XPB read.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a switch statement instead of ifs for code dependent
on chip version. While at it make sure we fail for unknown
chip revisions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NFP5000 to supported chips, the chip is backward compatible
with NFP4000 and NFP6000, so core PCIe code needs to handle it
the same way as 4k and 6k.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In multi-host scenarios Management FW may allocate MAC addresses
at runtime, we have to use the indirect lookup to find them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management FW can adjust some of the information in the HWinfo table
at runtime. In some cases reading the table directly will not yield
correct results. Add a NSP command for looking up information.
Up until now we weren't making use of any of the values which may
get adjusted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable easier FW distribution NFP can now automatically
select between FW stored on the flash and loaded from the
kernel.
If FW loading policy is set to auto it will compare the
versions of FW from the host and from the flash and load
the newer one. If FW type doesn't match (e.g. one advanced
application vs another) the FW from the host takes precedence,
unless one of them is the basic NIC firmware, in which case
the non-basic-NIC FW is selected.
This automatic selection mechanism requires we inform user
what the verdict was. Print a message to the logs explaining
the decision and the reason.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flash may contain a default NFP application FW. This application
can either be put there by the user (with ethtool -f) or shipped
with the card. If file system FW is not found, attempt to load
this flash stored app FW.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is already a fair number of arguments to nfp_nsp_command()
family of functions. Encapsulate them into structures to make
adding new ones easier. No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2018-08-28
This series contains new features and implementation updates for the
ice driver.
Anirudh reworks the current flex programming logic to add support for
a second flex descriptor profile. Updated the transmit scheduler
code to handle changes to the spec, specifically the firmware expects
a 4KB buffer at all times so fix the default scheduler topology buffer
size. Also the maximum children per node per layer is replaced by
maximum sibling group size. Adds a check to ensure a reset is not in
progress before exercising a control queue operation. Refactored the
switch rule management functions and structures to simply the logic and
to add a common function to search for a rule entry and add a new rule
entry. Refactored the VSI allocation, deletion and rebuild flow so that
on reset we can restore all the filters that were previously added. Did
some spring cleaning of define names and macros.
Dan updates the admin queue command for requesting resource ownership
to the latest specification by adding new enum's and change the locks.
Zhenning optimizes the driver by using the existing buffer in a
structure directly versus a local array.
Chinh implements handlers for ethtool for get and set link settings.
Sudheer implements transmit hang/timeout detection and malicious driver
detection in the driver.
Md Fahad Iqbal implements the get and set bridge mode operations.
Hieu adds the ability for firmware logging during initialization.
Brett updates the driver to only enable VSI transmit and receive pruning
when VLAN 0 is active, and when VLAN 0 is removed/not active, pruning is
disabled.
Akeem adds a flag to use for stopping the service task.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When failing the request because we can't support that offload,
reporting EOPNOTSUPP makes much more sense than ENXIO.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There seems to be a problem in the x540's internal switch wherein if SR-IOV
mode is enabled and an offloaded IPsec packet is sent to a local VF,
the packet is silently dropped. This might never be a problem as it is
somewhat a corner case, but if someone happens to be using IPsec offload
from the PF to a VF that just happens to get migrated to the local box,
communication will mysteriously fail.
Not good.
A simple way to protect from this is to simply not allow any IPsec offloads
for outgoing packets when num_vfs != 0. This doesn't help any offloads that
were created before SR-IOV was enabled, but we'll get to that later.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the IPsec initialization into the driver startup and
add the Rx and Tx processing hooks.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the IPsec offload support code. This is based off of the similar
code in ixgbe, but instead of writing the SA registers, the VF asks
the PF to setup the offload by sending the offload information to the
PF via the standard mailbox.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up the register definitions for using IPsec offloads and
add the new mailbox message IDs.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add an add and a delete message for IPsec offload requests from
the VF. These call into the IPsec functions that can translate
the message buffer into a useful IPsec offload.
These new messages bump the mbox API version to 1.4.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a private flag to expressly enable support for VF IPsec offload.
The VF will have to be "trusted" in order to use the hardware offload,
but because of the general concerns of managing VF access, we want to
be sure the user specifically is enabling the feature.
This is likely a candidate for becoming a netdev feature flag.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add functions to translate VF IPsec offload add and delete requests
into something the existing code can work with.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull out a couple of values from a function so they can be used
later elsewhere.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restore the IPsec hardware IP table after reloading the SA tables.
This doesn't make much difference now, but will matter when we add
support for VF IPsec offloads.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The software SA record counters should not be cleared when clearing
the hardware tables. This causes the counters to be out of sync
after a driver reset.
Fixes: 63a67fe229 ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While VF2VF with RSS communication, RSS Type were wrongly recognized
and RSS hash was not calculated as it should be. Packets was
distributed on various queues by accident.
This commit fixes that behaviour and causes proper RSS Type recognition.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add check for FW NVM recovery mode during driver initialization and
service task. If in recovery mode, log message and unregister device
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the "ice" prefix for the driver version string and bump version
to 0.7.1-k.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces SERVICE_DIS flag to use for stopping service task.
This flag will be checked before scheduling new tasks. Also add new
functions ice_service_task_stop to stop service task.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VLAN pruning is not valid when VLAN 0 is not active. If VLAN
pruning is enabled and VLAN 0 is not active (8021q driver not loaded)
then normal, non-VLAN, traffic will not pass.
TX/RX VLAN pruning is enabled when the VLAN 0 is added to the
active_vlan bitmap and it is disabled when VLAN 0 is removed from the
active_vlan bitmap.
So, only enable VLAN pruning when VLAN 0 is active. Setting RX VLAN
pruning causes the switch to drop received VLAN packets when there
are no matching VLAN ids in the associated VSI's switch filters. Setting
TX pruning makes it so the switch will not send out any packets with
VLAN tags that don't match the associated VSI's switch filters.
With this patch, if the VF or PF tries to send a VLAN tagged packet with
a VLAN tag that it does not have a pruning rule for it will trigger an
MDD event. For example, if PF0 has VLAN10 and VLAN11 interfaces and
scapy is used to send a packet with VLAN8 then the MDD is triggered.
Also make ice_vsi_kill_vlan return a value which the caller can check
before updating VLAN related data structures (counts, pruning bits, etc.).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To enable FW logging, the "cq_en" and "uart_en" enable bits of the
"fw_log" element in struct ice_hw need to set accordingly based on
some user-provided parameters during driver loading. To select which
FW log events to be emitted, the "cfg" elements of corresponding FW
modules in the "evnts" array member of "fw_log" need to be configured.
Signed-off-by: Hieu Tran <hieu.t.tran@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_bridge_getlink returns the current bridge mode using
ndo_dflt_bridge_getlink and the mode parameter available in
first_switch->bridge_mode.
ice_bridge_setlink is invoked when the bridge mode needs to
changed. The value to be changed to is available as a netlink
message which is parsed in this function. If the mode has to
be changed, switch_flags is set appropriately (set ALLOW_LB
for VEB mode and clear it for VEPA mode) and ice_aq_update_vsi
is called. Also change the unicast switch filter rules.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a malicious operation is detected, the firmware triggers an
interrupt, which is then picked up by the service task (specifically by
ice_handle_mdd_event). A reset is scheduled if required.
Tx hang detection works in a similar way, except the logic here monitors
the VSI's Tx queues and tries to revive them if stalled. If the hang is
not resolved, the kernel eventually calls ndo_tx_timeout, which is
handled by ice_tx_timeout.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the existing register definitions.
1) Several instances of long defines names used in the BIT() macro
were replaced to use the actual values they represent. As a
result some defines for shifts (ending with _S) that were used
only to create bitmasks were removed completely.
2) Apply more consistent tab spacing.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements handlers for ethtool get_link_ksettings and
set_link_ksettings. Helper functions use by these handlers are also
introduced in this patch.
Signed-off-by: Chinh Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors aspects of the VSI allocation, deletion and rebuild
flow. Some of the more noteworthy changes are described below.
1) On reset, all switch filters applied in the hardware are lost. In
the rebuild flow, only MAC and broadcast filters are being restored.
Instead, use a new function ice_replay_all_fltr to restore all the
filters that were previously added. To do this, remove calls to
ice_remove_vsi_fltr to prevent cleaning out the internal bookkeeping
structures that ice_replay_all_fltr uses to replay filters.
2) Introduce a new state bit __ICE_PREPARED_FOR_RESET to distinguish the
PF that requested the reset (and consequently prepared for it) from
the rest of the PFs. These other PFs will prepare for reset only
when they receive an interrupt from the firmware.
3) Use new functions ice_add_vsi and ice_free_vsi to create and destroy
VSIs respectively. These functions accept a handle to uniquely
identify a VSI. This same handle is required to rebuild the VSI post
reset. To prevent confusion, the existing ice_vsi_add was renamed to
ice_vsi_init.
4) Enhance ice_vsi_setup for the upcoming SR-IOV changes and expose a
new wrapper function ice_pf_vsi_setup to create PF VSIs. Rework the
error handling path in ice_setup_pf_sw.
5) Introduce a new function ice_vsi_release_all to release all PF VSIs.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is an adaptation of the work originally done by Grishma
Kotecha <grishma.kotecha@intel.com> that in summary refactors the
switch filtering logic in the driver. More specifically,
- Update the recipe structure to also store list of rules
- Update the existing code for recipes like MAC, VLAN, ethtype etc to
use list head that is attached to switch recipe structure
- Add a common function to search for a rule entry and add a new rule
entry. Update the code to use this new function.
- Refactor the rem_handle_vsi_list function to simplify the logic
CC: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the buffer in the s_rule structure directly instead of using
a local array eth_hdr[DUMMY_ETH_HDR_LEN]
Signed-off-by: Zhenning Xiao <zhenning.xiao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once reset is issued, the driver loses all control queue interfaces.
Exercising control queue operations during reset is incorrect and
may result in long timeouts.
This patch introduces a new field 'reset_ongoing' in the hw structure.
This is set to 1 by the core driver when it receives a reset interrupt.
ice_sq_send_cmd checks reset_ongoing before actually issuing the control
queue operation. If a reset is in progress, it returns a soft error code
(ICE_ERR_RESET_PENDING) to the caller. The caller may or may not have to
take any action based on this return. Once the driver knows that the
reset is done, it has to set reset_ongoing back to 0. This will allow
control queue operations to be posted to the hardware again.
This "bail out" logic was specifically added to ice_sq_send_cmd (which
is pretty low level function) so that we have one solution in one place
that applies to all types of control queues.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Align Request Resource Ownership AQ command (0x0008) to the latest
specification. This includes:
- Correcting the resource IDs for the Global Cfg and Change locks.
- new enum ICE_CHANGE_LOCK_RES_ID
- new enum ICE_GLOBAL_CFG_LOCK_RES_ID
- Altering the flow for Global Config Lock to allow only the first PF to
download the package.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) The maximum device nodes is a global value and shared by the whole
device. Add element AQ command would fail if there is no space to
add new nodes so the check for max nodes isn't required. So remove
ice_sched_get_num_nodes_per_layer and ice_sched_val_max_nodes.
2) In ice_sched_add_elems, set default node's CIR/EIR bandwidth weight.
3) Fix default scheduler topology buffer size as the firmware expects
a 4KB buffer at all times, and will error out if one of any other
size is provided.
4) In the latest spec, max children per node per layer is replaced by
max sibling group size. Now it provides the max children of the below
layer node, not the current layer node.
5) Fix some newline/whitespace issues for consistency.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver can support two flex descriptor profiles, ICE_RXDID_FLEX_NIC
and ICE_RXDID_FLEX_NIC_2. This patch reworks the current flex programming
logic to add support for the latter profile.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks.
2) Better fix for AB-BA deadlock in packet scheduler code, from Cong
Wang.
3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel
Borkmann.
4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent
attackers using it as a side-channel. From Eric Dumazet.
5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva.
6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin
Liu.
7) hns and hns3 bug fixes from Huazhong Tan.
8) Fix RIF leak in mlxsw driver, from Ido Schimmel.
9) iova range check fix in vhost, from Jason Wang.
10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend.
11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng.
12) Memory exposure in TCA_U32_SEL handling, from Kees Cook.
13) TCP BBR congestion control fixes from Kevin Yang.
14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger.
15) qed driver fixes from Tomer Tayar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: sched: Fix memory exposure from short TCA_U32_SEL
qed: fix spelling mistake "comparsion" -> "comparison"
vhost: correctly check the iova range when waking virtqueue
qlge: Fix netdev features configuration.
net: macb: do not disable MDIO bus at open/close time
Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency"
net: macb: Fix regression breaking non-MDIO fixed-link PHYs
mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge
i40e: fix condition of WARN_ONCE for stat strings
i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled
ixgbe: fix driver behaviour after issuing VFLR
ixgbe: Prevent unsupported configurations with XDP
ixgbe: Replace GFP_ATOMIC with GFP_KERNEL
igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback()
igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init()
igb: Use an advanced ctx descriptor for launchtime
e1000: ensure to free old tx/rx rings in set_ringparam()
e1000: check on netif_running() before calling e1000_up()
ixgb: use dma_zalloc_coherent instead of allocator/memset
ice: Trivial formatting fixes
...
Trivial fix to spelling mistake in DP_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes: 6c36a70744 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bde4975310.
All legacy clock implementations now implement clk_set_rate() (Some
implementations may be dummies, though).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arnd.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 739de9a156 ("net: macb: Reorganize macb_mii bringup") broke
initializing macb on the EVB-KSZ9477 eval board.
There, of_mdiobus_register was called even for the fixed-link representing
the RGMII-link to the switch with the result that the driver attempts to
enumerate PHYs on a non-existent MDIO bus:
libphy: MACB_mii_bus: probed
mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0
[snip]
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31
The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO,
and calling of_phy_register_fixed_link later on fails because it tries
to claim the same GPIO:
macb f0028000.ethernet: broken fixed-link specification
Fix this by registering the fixed-link before calling mdiobus_register.
Fixes: 739de9a156 ("net: macb: Reorganize macb_mii bringup")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b10df596b ("i40e: use WARN_ONCE to replace the commented
BUG_ON size check") introduced a warning check to make sure
that the size of the stat strings was always the expected value. This
code accidentally inverted the check of the data pointer. Fix this so
that we accurately count the size of the stats we copied in.
This fixes an erroneous WARN kernel splat that occurs when requesting
ethtool statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If interface is connected to switch port configured for DCB there are
TX timeouts when bringing up interface. Problem started appearing after
adding in i40e driver code mqprio hardware offload mode. In function
i40e_vsi_configure_bw_alloc was added resetting BW rate which should
be executing when mqprio qdisc is removed but was also when there was
no mqprio qdisc added and DCB was enabled. In this patch was added
additional check for DCB flag so now when DCB is enabled the correct
DCB configs from before mqprio patch are restored.
Signed-off-by: Martyna Szapar <martyna.szapar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since VFLR doesn't clear VFMBMEM (VF Mailbox Memory)
and is not re-enabling queues correctly we should fix
this behavior.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes address comments by Jakub Kicinski on
commit 38b7e7f8ae ("ixgbe: Do not allow LRO or MTU change with XDP").
Change the MTU check with XDP to allow any supported value and only
reject those outside of the range as opposed to rejecting any change
when XDP is active. In situations where MTU size is not supported,
return -EINVAL instead of -EPERM.
Add checks when enabling SRIOV, DCB, or adding L2FW offloaded device
as they are not supported with XDP.
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_fcoe_ddp_setup(), ixgbe_setup_fcoe_ddp_resources() and
ixgbe_sw_init() are never called in atomic context.
They call kmalloc(), dma_pool_alloc() and kzalloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_integrated_phy_loopback() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb_sw_init() is never called in atomic context.
It calls kzalloc() and kcalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On i210, Launchtime (TxTime) requires the usage of an "Advanced
Transmit Context Descriptor" for retrieving the timestamp of a packet.
The igb driver correctly builds such descriptor on the segmentation
flow (i.e. igb_tso()) or on the checksum one (i.e. igb_tx_csum()), but the
feature is broken for AF_PACKET if the IGB_TX_FLAGS_VLAN is not set,
which happens due to an early return on igb_tx_csum().
This flag is only set by the kernel when a VLAN interface is used,
thus we can't just rely on it. Here we are fixing this issue by checking
if launchtime is enabled for the current tx_ring before performing the
early return.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value
and the old tx/rx rings are freed only when the device is up. There are resource
leaks on old tx/rx rings when the device is not up. This bug is reported by COD,
a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in
'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is not up, the call to 'e1000_up()' from the error handling path
of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer
dereference. The null-pointer dereference is triggered in function
'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am
building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling
'e1000_up()' in 'e1000_set_ringparam()'.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL
-----BEGIN PGP SIGNATURE-----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=ACVk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 32-bit SoC platform updates from Olof Johansson:
"Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (112 commits)
ARM: uniphier: select RESET_CONTROLLER
arm64: uniphier: select RESET_CONTROLLER
ARM: uniphier: remove empty Makefile
ARM: exynos: Clear global variable on init error path
ARM: exynos: Remove outdated maintainer information
ARM: shmobile: Always enable ARCH_TIMER on SoCs with A7 and/or A15
ARM: shmobile: r8a7779: hide unused r8a7779_platform_cpu_kill
soc: r9a06g032: don't build SMP files for non-SMP config
ARM: shmobile: Add the R9A06G032 SMP enabler driver
ARM: at91: pm: configure wakeup sources for ULP1 mode
ARM: at91: pm: add PMC fast startup registers defines
ARM: at91: pm: Add ULP1 mode support
ARM: at91: pm: Use ULP0 naming instead of slow clock
ARM: hisi: handle of_iomap and fix missing of_node_put
ARM: hisi: check of_iomap and fix missing of_node_put
ARM: hisi: fix error handling and missing of_node_put
ARM: mx5: Set the DBGEN bit in ARM_GPC register
ARM: imx51: Configure M4IF to avoid visual artifacts
ARM: imx: call imx6sx_cpuidle_init() conditionally for 6sll
ARM: imx: fix i.MX6SLL build
...
1) Add missing "\n" when printing link event error message.
2) Update dev_err statement in probe.
3) Add function description for ice_clear_pf_cfg.
4) Fix coding style for ice_acquire_nvm.
5) netdev->mtu is unsigned so use %u.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_vsi_setup_[tx|rx]_rings, err is uninitialized which can result in
a garbage value return to the caller. Fix that.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) When ice_ena_msix_range() fails to reserve vectors, a devm_kfree()
warning was seen in the error flow path. So check pf->irq_tracker
before use in ice_clear_interrupt_scheme().
2) In ice_vsi_cfg(), check vsi->netdev before use.
3) In ice_get_link_status, check link_up before use.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the following interrupt causes that are not applicable or not
handled:
- PFINT_OICR_HLP_RDY_M
- PFINT_OICR_CPM_RDY_M
- PFINT_OICR_GPIO_M
- PFINT_OICR_STORM_DETECT_M
Add the following interrupt cause that's actually handled in ice_misc_intr:
- PFINT_OICR_PE_CRITERR_M
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the struct ice_aqc_vsi_props the field port_vlan_flags is an
overloaded term because it is used for both port VLANs (PVLANs) and
regular VLANs. This is an issue and is very confusing especially when
dealing with VFs because normal VLANs and port VLANs are not the same.
To fix this the field was renamed to vlan_flags and all of the #define's
labeled *_PVLAN_* were renamed to *_VLAN_* if they are not specific to
port VLANs.
Also in ice_vsi_manage_vlan_stripping, set the ICE_AQ_VSI_VLAN_MODE_ALL
bit to allow the driver to add a VLAN tag to all packets it sends.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, we use a combination of ilog2 and is_power_of_2() to
calculate the next power of 2 for the qcount. This appears to be causing
a warning on some combinations of GCC and the Linux kernel:
MODPOST 1 modules
WARNING: "____ilog2_NaN" [ice.ko] undefined!
This appears to because because GCC realizes that qcount could be zero
in some circumstances and thus attempts to link against the
intentionally undefined ___ilog2_NaN function.
The order_base_2 function is intentionally defined to return 0 when
passed 0 as an argument, and thus will be safe to use here.
This not only fixes the warning but makes the resulting code slightly
cleaner, and is really what we should have used originally.
Also update the comment to make it more clear that we are rounding up,
not just incrementing the ilog2 of qcount unconditionally.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a consolidation of multiple bug fixes for control queue
processing.
1) In ice_clean_adminq_subtask() remove unnecessary reads/writes to
registers. The bits PFINT_FW_CTL, PFINT_MBX_CTL and PFINT_SB_CTL
are not set when an interrupt arrives, which means that clearing them
again can be omitted.
2) Get an accurate value in "pending" by re-reading the control queue
head register from the hardware.
3) Fix a corner case involving lost control queue messages by checking
for new control messages (using ice_ctrlq_pending) before exiting the
cleanup routine.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean control queues only when they are initialized. One of the ways to
validate if the basic initialization is done is by checking value of
cq->sq.head and cq->rq.head variables that specify the register address.
This patch adds a check to avoid NULL pointer dereference crash when tried
to shutdown uninitialized control queue.
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is not safe to have the string table for statistics change order or
size over the lifetime of a given netdevice. This is because of the
nature of the 3-step process for obtaining stats. First, user space
performs a request for the size of the strings table. Second it performs
a separate request for the strings themselves, after allocating space
for the table. Third, it requests the stats themselves, also allocating
space for the table.
If the size decreased, there is potential to see garbage data or stats
values. In the worst case, we could potentially see stats values become
mis-aligned with their strings, so that it looks like a statistic is
being reported differently than it actually is.
Even worse, if the size increased, there is potential that the strings
table or stats table was not allocated large enough and the stats code
could access and write to memory it should not, potentially resulting in
undefined behavior and system crashes.
It isn't even safe if the size always changes under the RTNL lock. This
is because the calls take place over multiple user space commands, so it
is not possible to hold the RTNL lock for the entire duration of
obtaining strings and stats. Further, not all consumers of the ethtool
API are the user space ethtool program, and it is possible that one
assumes the strings will not change (valid under the current contract),
and thus only requests the stats values when requesting stats in a loop.
Finally, it's not possible in the general case to detect when the size
changes, because it is quite possible that one value which could impact
the stat size increased, while another decreased. This would result in
the same total number of stats, but reordering them so that stats no
longer line up with the strings they belong to. Since only size changes
aren't enough, we would need some sort of hash or token to determine
when the strings no longer match. This would require extending the
ethtool stats commands, but there is no more space in the relevant
structures.
The real solution to resolve this would be to add a completely new API
for stats, probably over netlink.
In the ice driver, the only thing impacting the stats that is not
constant is the number of queues. Instead of reporting stats for each
used queue, report stats for each allocated queue. We do not change the
number of queues allocated for a given netdevice, as we pass this into
the alloc_etherdev_mq() function to set the num_tx_queues and
num_rx_queues.
This resolves the potential bugs at the slight cost of displaying many
queue statistics which will not be activated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use define for the unit size shift of the Rx LAN context descriptor base
address instead of the magic number 7.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is already a check for owner == ICE_SCHED_NODE_OWNER_LAN at the
beginning of ice_sched_update_vsi_child_nodes. Remove the additional
check to address the static analysis tool smatch issue "warn: we tested
'owner' before and it was 'false'".
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the following smatch errors:
1) Fix "odd binop '0x0 & 0xc'" when performing the bitwise-and with a
constant value of zero (ICE_AQC_GSET_RSS_LUT_TABLE_SIZE_128_FLAG).
Remove a similar bitwise-and with 0 in ice_add_marker_act() and use the
right mask ICE_LG_ACT_GENERIC_OFFSET_M in the expression.
2) Fix a similar issue "odd binop '0x0 & 0x1800' in ice_req_irq_msix_misc.
3) Fix "odd binop '0x380000 & 0x7fff8'" in ice_add_marker_act(). Also, use
a new define ICE_LG_ACT_GENERIC_OFF_RX_DESC_PROF_IDX instead of magic
number '7'.
4) Fix warn: odd binop '0x0 & 0x18' in ice_set_dflt_vsi_ctx() by removing
unnecessary logic to explicitly unset bits 3 and 4 in port_vlan_bits.
These bits are unset already by the memset on ctxt->info.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'truesize' is supposed to be u32, not int, so fix it.
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of
PAGE_SIZE is 65536(64K). But the type of page_offset is u16, it will
overflow. So change it to u32, when "CONFIG_ARM64_64K_PAGES" enabled.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update hns to drop the hns_nic_get_headlen function in favour of
eth_get_headlen, and hence also removes now redundant hns_nic_get_headlen.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->truesize is not meant to be tracking amount of used bytes in a skb,
but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment, we have to
account the full size of the fragment.
So skb_add_rx_frag needs to calculate the length of the entire buffer into
turesize.
Fixes: 9cbe9fd521 ("net: hns: optimize XGE capability by reducing cpu usage")
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'truesize' is supposed to be u32, not int, so fix it.
Signed-off-by: Huazhong tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE
is 65536(64K). But the type of length and page_offset are u16, they will
overflow. So change them to u32.
Fixes: 6fe6611ff2 ("net: add Hisilicon Network Subsystem hnae framework support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90b73b77d0, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.
Fixes: 90b73b77d0 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep sending mailbox commands to the MFW when it is not responsive ends up
with a redundant amount of timeout expiries.
This patch prints the MCP status on the first command which is not
responded, and blocks the following commands.
Since the (un)load request commands might be not responded due to other
PFs, the patch also adds the option to skip the blocking upon a failure.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW manages an internal lock to prevent concurrent hardware
(de)initialization of different PFs.
This, together with the busy-waiting for the MFW's responses for commands,
might lead to a deadlock during concurrent load or unload of PFs.
This patch adds the option to sleep within the busy-waiting, and uses it
for the (un)load requests (which are not sent from an interrupt context) to
prevent the possible deadlock.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix races in IPVS, from Tan Hu.
2) Missing unbind in matchall classifier, from Hangbin Liu.
3) Missing act_ife action release, from Vlad Buslov.
4) Cure lockdep splats in ila, from Cong Wang.
5) veth queue leak on link delete, from Toshiaki Makita.
6) Disable isdn's IIOCDBGVAR ioctl, it exposes kernel addresses. From
Kees Cook.
7) RCU usage fixup in XDP, from Tariq Toukan.
8) Two TCP ULP fixes from Daniel Borkmann.
9) r8169 needs REALTEK_PHY as a Kconfig dependency, from Heiner
Kallweit.
10) Always take tcf_lock with BH disabled, otherwise we can deadlock
with rate estimator code paths. From Vlad Buslov.
11) Don't use MSI-X on RTL8106e r8169 chips, they don't resume properly.
From Jian-Hong Pan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ip6_vti: fix creating fallback tunnel device for vti6
ip_vti: fix a null pointer deferrence when create vti fallback tunnel
r8169: don't use MSI-X on RTL8106e
net: lan743x_ptp: convert to ktime_get_clocktai_ts64
net: sched: always disable bh when taking tcf_lock
ip6_vti: simplify stats handling in vti6_xmit
bpf: fix redirect to map under tail calls
r8169: add missing Kconfig dependency
tools/bpf: fix bpf selftest test_cgroup_storage failure
bpf, sockmap: fix sock_map_ctx_update_elem race with exist/noexist
bpf, sockmap: fix map elem deletion race with smap_stop_sock
bpf, sockmap: fix leakage of smap_psock_map_entry
tcp, ulp: fix leftover icsk_ulp_ops preventing sock from reattach
tcp, ulp: add alias for all ulp modules
bpf: fix a rcu usage warning in bpf_prog_array_copy_core()
samples/bpf: all XDP samples should unload xdp/bpf prog on SIGTERM
net/xdp: Fix suspicious RCU usage warning
net/mlx5e: Delete unneeded function argument
Documentation: networking: ti-cpsw: correct cbs parameters for Eth1 100Mb
isdn: Disable IIOCDBGVAR
...
Found the ethernet network on ASUS X441UAR doesn't come back on resume
from suspend when using MSI-X. The chip is RTL8106e - version 39.
[ 21.848357] libphy: r8169: probed
[ 21.848473] r8169 0000:02:00.0 eth0: RTL8106e, 0c:9d:92:32:67:b4, XID
44900000, IRQ 127
[ 22.518860] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 29.458041] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
[ 63.227398] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full -
flow control off
[ 124.514648] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
Here is the ethernet controller in detail:
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
Falling back to MSI fixes the issue.
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timekeeping_clocktai64() has been renamed to ktime_get_clocktai_ts64()
for consistency with the other ktime_get_* access functions.
Rename the new caller that has come up as well.
Question: this is the only ptp driver that sets the hardware time
to the current system time in TAI. Why does it do that?
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Now that we switched the r8169 driver to use phylib, there's a
dependency on the Realtek PHY drivers. This dependency was missing
in Kconfig.
Reported-by: Jouni Mettälä <jtmettala@gmail.com>
Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rdma.git merge resolution for the 4.19 merge window
Conflicts:
drivers/infiniband/core/rdma_core.c
- Use the rdma code and revise with the new spelling for
atomic_fetch_add_unless
drivers/nvme/host/rdma.c
- Replace max_sge with max_send_sge in new blk code
drivers/nvme/target/rdma.c
- Use the blk code and revise to use NULL for ib_post_recv when
appropriate
- Replace max_sge with max_recv_sge in new blk code
net/rds/ib_send.c
- Use the net code and revise to use NULL for ib_post_recv when
appropriate
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
priv argument is not used by the function, delete it.
Fixes: a89842811e ("net/mlx5e: Merge per priority stats groups")
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAltwm2geHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGITkH/iSzkVhT2OxHoir0
mLVzTi7/Z17L0e/ELl7TvAC0iLFlWZKdlGR0g3b4/QpXLPmNK4HxiDRTQuWn8ke0
qDZyDq89HqLt+mpeFZ43PCd9oqV8CH2xxK3iCWReqv6bNnowGnRpSStlks4rDqWn
zURC/5sUh7TzEG4s997RrrpnyPeQWUlf/Mhtzg2/WvK2btoLWgu5qzjX1uFh3s7u
vaF2NXVJ3X03gPktyxZzwtO1SwLFS1jhwUXWBZ5AnoJ99ywkghQnkqS/2YpekNTm
wFk80/78sU+d91aAqO8kkhHj8VRrd+9SGnZ4mB2aZHwjZjGcics4RRtxukSfOQ+6
L47IdXo=
=sJkt
-----END PGP SIGNATURE-----
Merge tag 'v4.18' into rdma.git for-next
Resolve merge conflicts from the -rc cycle against the rdma.git tree:
Conflicts:
drivers/infiniband/core/uverbs_cmd.c
- New ifs added to ib_uverbs_ex_create_flow in -rc and for-next
- Merge removal of file->ucontext in for-next with new code in -rc
drivers/infiniband/core/uverbs_main.c
- for-next removed code from ib_uverbs_write() that was modified
in for-rc
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
-----BEGIN PGP SIGNATURE-----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=2Dmn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
* pci/aspm:
PCI: Remove unnecessary include of <linux/pci-aspm.h>
iwlwifi: Remove unnecessary include of <linux/pci-aspm.h>
ath9k: Remove unnecessary include of <linux/pci-aspm.h>
igb: Remove unnecessary include of <linux/pci-aspm.h>
PCI/ASPM: Convert to use sysfs_match_string() helper
- Revert two ACPICA commits that are not needed any more (Erik
Schmauss).
- Rework property graph support in the ACPI device properties
framework to make it behave more like the analogous DT code
and update the documentation of it (Sakari Ailus).
- Change the default ACPI device status after initialization
to ACPI_STA_DEFAULT instead of 0 (Hans de Goede).
- Add a special platform driver for enumerating multiple I2C devices
hooked up to the same object in the ACPI tables (Hans de Goede).
- Fix the ACPI battery driver to avoid reporting full capacity on
systems without support for that and clean it up (Hans de Goede,
Dmitry Rozhkov, Lucas Rangit Magasweran).
- Add two system wakeup quirks to the ACPI EC driver (Aaron Ma,
Mika Westerberg).
- Add the touchscreen on Dell Venue Pro 7139 to the list of "always
present" devices to make it work (Tristian Celestin).
- Revert a special tables handling quirk for Dell XPS 9570 and
Precision M5530 which is not needed any more (Kai Heng Feng).
- Add support for a new OEM _OSI string to allow system vendors to
work around issues with NVidia HDMI audio (Alex Hung).
- Prevent the ACPI button driver from reporting excessive system
wakeup events and clean it up (Ravi Chandra Sadineni, Randy Dunlap).
- Clean up two minor code style issues in the ACPI core and GHES
handling on ARM64 (Dongjiu Geng, John Garry, Tom Todd).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5mW8
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These revert two ACPICA commits that are not needed any more, rework
the property graphs support in ACPI to be more aligned with the
analogous DT code, add some new quirks and remove one that isn't
needed any more, add a special platform driver to enumerate multiple
I2C devices hooked up to the same device object in the ACPI tables and
update the battery and button drivers.
Specifics:
- Revert two ACPICA commits that are not needed any more (Erik
Schmauss).
- Rework property graph support in the ACPI device properties
framework to make it behave more like the analogous DT code and
update the documentation of it (Sakari Ailus).
- Change the default ACPI device status after initialization to
ACPI_STA_DEFAULT instead of 0 (Hans de Goede).
- Add a special platform driver for enumerating multiple I2C devices
hooked up to the same object in the ACPI tables (Hans de Goede).
- Fix the ACPI battery driver to avoid reporting full capacity on
systems without support for that and clean it up (Hans de Goede,
Dmitry Rozhkov, Lucas Rangit Magasweran).
- Add two system wakeup quirks to the ACPI EC driver (Aaron Ma, Mika
Westerberg).
- Add the touchscreen on Dell Venue Pro 7139 to the list of "always
present" devices to make it work (Tristian Celestin).
- Revert a special tables handling quirk for Dell XPS 9570 and
Precision M5530 which is not needed any more (Kai Heng Feng).
- Add support for a new OEM _OSI string to allow system vendors to
work around issues with NVidia HDMI audio (Alex Hung).
- Prevent the ACPI button driver from reporting excessive system
wakeup events and clean it up (Ravi Chandra Sadineni, Randy
Dunlap).
- Clean up two minor code style issues in the ACPI core and GHES
handling on ARM64 (Dongjiu Geng, John Garry, Tom Todd)"
* tag 'acpi-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
platform/x86: Add ACPI i2c-multi-instantiate pseudo driver
ACPI / x86: utils: Remove status workaround from acpi_device_always_present()
ACPI / scan: Create platform device for fwnodes with multiple i2c devices
ACPI / scan: Initialize status to ACPI_STA_DEFAULT
ACPI / EC: Add another entry for Thinkpad X1 Carbon 6th
ACPI: bus: Fix a pointer coding style issue
arm64 / ACPI: clean the additional checks before calling ghes_notify_sea()
ACPI / scan: Add static attribute to indirect_io_hosts[]
ACPI / battery: Do not export energy_full[_design] on devices without full_charge_capacity
ACPI / EC: Use ec_no_wakeup on ThinkPad X1 Yoga 3rd
ACPI / battery: get rid of negations in conditions
ACPI / battery: use specialized print macros
ACPI / battery: reorder headers alphabetically
ACPI / battery: drop inclusion of init.h
ACPI: battery: remove redundant old_present check on insertion
ACPI: property: graph: Update graph documentation to use generic references
ACPI: property: graph: Improve graph documentation for port/ep numbering
ACPI: property: graph: Fix graph documentation
ACPI: property: Update documentation for hierarchical data extension 1.1
ACPI: property: Document key numbering for hierarchical data extension refs
...
Revision(0x20) HW does not support enabling or disabling individual
netdev's HW_VLAN_CTAG_FILTER feature, and Revision(0x21) supports
enabling or disabling individual netdev's HW_VLAN_CTAG_FILTER
feature.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS3_RING_TX_RING_TC_REG register is used to map tx ring to
specific tc, the tx queue to tc mapping is needed by the hardware
to do the correct tx schedule.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no HNS3_RING_TX_RING_BD_LEN_REG register according
to UM, so this patch removes it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user set the channel num using "ethtool -L ethX", the desc num
of BD will set to default value, which will cause desc num set by
user lost problem.
This patch fixes it by restoring the desc num set by user when setting
channel num.
Fixes: 09f2af6405 ("net: hns3: add support to modify tqps number")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For marvell phy m88e1510, bit SUPPORTED_FIBRE of phydev->supported
is default on. Both phy_resume() and phy_suspend() will check the
SUPPORTED_FIBRE bit and write register of fibre page.
Currently in hns3 driver, the SUPPORTED_FIBRE bit will be cleared
after phy_connect_direct() finished. Because phy_resume() is called
in phy_connect_direct(), and phy_suspend() is called when disconnect
phy device, so the operation for fibre page register is not symmetrical.
It will cause phy link issue when reload hns3 driver.
This patch fixes it by disable the SUPPORTED_FIBRE before connecting
phy.
Fixes: 256727da73 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function call of phy_connect_direct will reinitialize phydev. Some
information like advertising will be lost. Phy_connect_direct only
needs to be called once. And driver can run well. This patch adds
some functions to ensure that phy_connect_direct is called only once
to solve the information of phydev lost problem occurring when we stop
the net and open it again.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the functional specification of hardware, the first
descriptor of response from command 'lookup vlan talbe' is not valid.
Currently, the first descriptor is parsed as normal value, which will
cause an expected error.
This patch fixes this problem by skipping the first descriptor.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for serdes loopback selftest in hns3
driver.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge ACPICA changes and updates of the ACPI device properties
framework for 4.19.
These revert two ACPICA commits that are not needed any more and
modify the properties graph support in ACPI to be more in-line with
the analogous DT code.
* acpica:
ACPICA: Update version to 20180629
ACPICA: Revert "iASL compiler: allow compilation of externals with paths that refer to existing names"
ACPICA: Revert "iASL: change processing of external op namespace nodes for correctness"
* acpi-property:
ACPI: property: graph: Update graph documentation to use generic references
ACPI: property: graph: Improve graph documentation for port/ep numbering
ACPI: property: graph: Fix graph documentation
ACPI: property: Update documentation for hierarchical data extension 1.1
ACPI: property: Document key numbering for hierarchical data extension refs
ACPI: property: Use data node name and reg property for graphs
ACPI: property: Allow direct graph endpoint references
ACPI: property: Make the ACPI graph API private
ACPI: property: Document hierarchical data extension references
ACPI: property: Allow making references to non-device nodes
ACPI: Convert ACPI reference args to generic fwnode reference args
The bnxt_coredump_record structure is very long, causing a warning
about possible stack overflow on 32-bit architectures:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c: In function 'bnxt_get_coredump':
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2989:1: error: the frame size of 1188 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
I could not see any reason to operate on an on-stack copy of the
structure before copying it back into the caller-provided buffer, which
also simplifies the code here.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining caller of this function is inside of an #ifdef
after another caller got removed. This causes a harmless warning
in some configurations:
drivers/net/ethernet/broadcom/bcmsysport.c:1068:13: error: 'bcm_sysport_resume_from_wol' defined but not used [-Werror=unused-function]
Removing the #ifdef around the PM functions simplifies the code
and avoids the problem but letting the compiler drop the unused
functions silently.
Fixes: 9e85e22713 ("net: systemport: Do not re-configure upon WoL interrupt")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added suspend/resume functions cause a build warning
when CONFIG_PM is disabled:
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c:324:12: error: 'stmmac_pci_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c:306:12: error: 'stmmac_pci_suspend' defined but not used [-Werror=unused-function]
Mark them as __maybe_unused so gcc can drop them silently.
Fixes: b7d0f08e91 ("net: stmmac: Fix WoL for PCI-based setups")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The utsname()->nodename string may be 64 bytes long, and it gets
copied without the trailing nul byte into the shorter record->system_name,
as gcc now warns:
In file included from include/linux/bitmap.h:9,
from include/linux/ethtool.h:16,
from drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:13:
In function 'strncpy',
inlined from 'bnxt_fill_coredump_record' at drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2863:2:
include/linux/string.h:254:9: error: '__builtin_strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
Using strlcpy() at least avoids overflowing the destination buffer
and adds proper nul-termination. It may still truncate long names
though, which probably can't be solved here.
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building without CONFIG_PTP_1588_CLOCK results in multiple failures,
this was obviously not well tested:
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_isr':
drivers/net/ethernet/microchip/lan743x_ptp.c:781:28: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
ptp_schedule_worker(ptp->ptp_clock, 0);
^~~~~~~~~
tx_ts_lock
drivers/net/ethernet/microchip/lan743x_ptp.c: In function 'lan743x_ptp_open':
drivers/net/ethernet/microchip/lan743x_ptp.c:879:6: error: unused variable 'ret' [-Werror=unused-variable]
int ret = -ENODEV;
^~~
At top level:
drivers/net/ethernet/microchip/lan743x_ptp.c:63:13: error: 'lan743x_ptp_tx_ts_enqueue_ts' defined but not used [-Werror=unused-function]
static void lan743x_ptp_tx_ts_enqueue_ts(struct lan743x_adapter *adapter,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
drivers/net/ethernet/microchip/lan743x_ethtool.c: In function 'lan743x_ethtool_get_ts_info':
drivers/net/ethernet/microchip/lan743x_ethtool.c:558:19: error: 'struct lan743x_ptp' has no member named 'ptp_clock'; did you mean 'tx_ts_lock'?
Those #ifdef checks are hard to get right, replace them all with
IS_ENABLED() checks that leave the same code visible to the compiler
but let it optimize out the unused bits based on the configuration.
Fixes: 07624df1c9 ("lan743x: lan743x: Add PTP support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan743x now fails to build when CONFIG_CRC16 is disabled:
drivers/net/ethernet/microchip/lan743x_main.o: In function crc16'
Force it on like all other users do.
Fixes: 4d94282afd ("lan743x: Add power management support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove 'Return:' information from functions which no longer
return a value. Also update name and return types of nfp_nffw_info
access functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last argument to mlx5_add_flow_rules passes the number of
destinations in the struct pointed to by the dest arg. Change the name
to better reflect this fact.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
lib/clock.c includes clock related functions which require ptp support.
Thus compile out lib/clock.c and add the needed function stubs in case
kconfig CONFIG_PTP_1588_CLOCK is off.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When vxlan is not enabled by kernel, no need to enable it in mlx5.
Compile out lib/vxlan.c if CONFIG_VXLAN is not selected.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Add new mlx5 Kconfig flag to allow selecting accelerated flow steering
support, and compile out en_arfs.c if not selected.
Move arfs declarations and definitions to en/fs.h header file.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Add new mlx5 Kconfig flag to allow selecting ethtool rx nfc support,
and compile out en_fs_ehtool.c if not selected.
Add en/fs.h header file to host all steering declarations and
definitions.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Move ethool rxnfc callback into en_fs_etthool file where they belong.
This will allow us to make many ethtool fs related helper functions
static.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for l4 proto ip field in ethtool flow steering.
Example: Redirect icmpv6 to rx queue #2
ethtool -U eth0 flow-type ip6 l4proto 58 action 2
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Have a parsing function per flow type, that converts from ethtool rx flow
spec to mlx5 flow spec.
Will be useful to add support for ip6 ethtool flow steering in the
next patch.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
- Enable mac_scsi PDMA on PowerBook 500,
- Generic dma_noncoherent_ops conversion,
- Time handling improvements,
- I/O accessor improvements,
- Conversion to MEMBLOCK and NO_BOOTMEM, to bring m68k in line with
other mainstream architectures,
- Miscellaneous fixes and cleanups,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW2rv8BUcZ2VlcnRAbGlu
dXgtbTY4ay5vcmcACgkQisJQ/WRJ8XBRAQD+O3x187pxeICV5LUC4SGtPj3kw07e
wr1NA0hnRqri77MBAPNx96fy0wnQAgMuvIghpEYqX6ha2O4NTxKUmLdxl/QL
=gJGl
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- Enable mac_scsi PDMA on PowerBook 500
- Generic dma_noncoherent_ops conversion
- Time handling improvements
- I/O accessor improvements
- Conversion to MEMBLOCK and NO_BOOTMEM, to bring m68k in line with
other mainstream architectures
- Miscellaneous fixes and cleanups
- Defconfig updates
* tag 'm68k-for-v4.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.18-rc6
m68k: switch to MEMBLOCK + NO_BOOTMEM
m68k/page_no.h: force __va argument to be unsigned long
m68k/bitops: convert __ffs to match generic declaration
m68k/io: Switch mmu variant to <asm-generic/io.h>
m68k/io: Move mem*io define guards to <asm/kmap.h>
Input: hilkbd - Add casts to HP9000/300 I/O accessors
net: mac8390: Use standard memcpy_{from,to}io()
m68k/io: Add missing ioremap define guards, fix typo
m68k: Remove unused set_clock_mmss() helpers
m68k: mac: Use time64_t in RTC handling
m68k: Use generic dma_noncoherent_ops
nubus: Set default dma mask for nubus_board devices
m68k/mac: Enable PDMA for PowerBook 500 series
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c: In function 'lio_set_link_ksettings':
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:392:6: warning:
variable 'is25G' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'print_port_info':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:5147:14: warning:
variable 'spd' set but not used [-Wunused-but-set-variable]
variable 'spd' is set but not used since
commit 547fd27241 ("cxgb4: Warn if device doesn't have enough PCI bandwidth")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been two reports that network doesn't come back on resume
from suspend when using MSI-X. Both cases affect the same chip version
(RTL8168g - version 40), on different systems. Falling back to MSI
fixes the issue.
Even though we don't really have a proof yet that the network chip
version is to blame, let's disable MSI-X for this version.
Reported-by: Steve Dodd <steved424@gmail.com>
Reported-by: Lou Reed <gogen@disroot.org>
Tested-by: Steve Dodd <steved424@gmail.com>
Tested-by: Lou Reed <gogen@disroot.org>
Fixes: 6c6aa15fde ("r8169: improve interrupt handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't store skb in app4 field of descriptor since it is
not being used anywhere (including hardware).
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not zero application specific fields in DMA descriptors.
The hardware does ignore them, so should software.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing descriptors to 256 from 128 and adjusting the NAPI weight
to 64 increases performace on Rx by ~20% on 64byte packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MMIO reads for remaining packets in queue occur (at least)twice per
invocation of netsec_process_rx(). We can use the packet descriptor to
identify if it's owned by the hardware and break out, avoiding the more
expensive MMIO read operations. This has a ~2% increase on the pps of the
Rx path when tested with 64byte packets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/neterion/vxge/vxge-config.c:1097:6: warning:
variable 'ret' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/neterion/vxge/vxge-config.c:2263:6: warning:
variable 'req_out' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/neterion/vxge/vxge-config.c:2262:22: warning:
variable 'status' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/neterion/vxge/vxge-config.c:2360:22: warning:
variable 'status' set but not used [-Wunused-but-set-variable]
enum vxge_hw_status status = VXGE_HW_OK;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP support includes:
Ingress, and egress timestamping.
One step timestamping available.
PTP clock support.
Periodic output support.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's exclusive with normal behaviour but if try to set vlan to one of
the reserved values is made, the cpsw runtime pm is broken.
Fixes: a6c5d14f51 ("drivers: net: cpsw: ndev: fix accessing to suspended device")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cases if some of the entries were not found in forwarding table
while killing vlan, the rest not needed entries still left in the
table. No need to stop, as entry was deleted anyway. So fix this by
returning error only after all was cleaned. To implement this, return
-ENOENT in cpsw_ale_del_mcast() as it's supposed to be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following smatch warnings:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2826 bnxt_fill_coredump_seg_hdr() error: strcpy() '"sEgM"' too large for 'seg_hdr->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2858 bnxt_fill_coredump_record() error: strcpy() '"cOrE"' too large for 'record->signature' (5 vs 4)
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2879 bnxt_fill_coredump_record() error: strcpy() 'utsname()->sysname' too large for 'record->os_name' (65 vs 32)
Fixes: 6c5657d085 ("bnxt_en: Add support for ethtool get dump.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LED identification support for liquidio TP copperhead cards.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 5e7baf0fcb ("qed/qede: Multi CoS support.")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_core_driver_put only traverse mlxsw_core_driver_list
to find the matched mlxsw_driver,but never used it.
So it can be removed safely.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events, the driver uses
a per CPU napi structure for this case. Some SoCs such as armada 3700
have a single interrupt for Ethernet events, the driver uses a global
napi structure for this case.
Current mvneta_config_rss() always operates the per cpu napi structure.
Fix it by operating a global napi for "single interrupt" case, and per
cpu napi structure for remaining cases.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 2636ac3cc2 ("net: mvneta: Add network support for Armada 3700 SoC")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have to configure the max jumbo frame size per chip
(sub-)version. It can be easily determined based on the chip family.
And new members of the RTL8168 family (if there are any) should be
automatically covered.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't have to configure the csum function per chip (sub-)version.
The distinction is simple, versions RTL8102e and from RTL8168c onwards
support csum_v2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the interrupt handler a little and make it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The asm headers shouldn't be included directly. asm/irq.h is
implicitly included by linux/interrupt.h, and instead of
asm/io.h include linux/io.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version number hasn't changed for ages and in general I doubt it
provides any benefit. The message in rtl_init_one() may even be
misleading because it's printed also if something fails in probe.
Therefore let's remove the version information.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
display Data Center bridging information in debug
fs.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array pci_speed is defined but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: 'pci_speed' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arrays mlxsw_i2c_driver_name and mlxsw_pci_driver_name are defined
but never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: 'mlxsw_i2c_driver_name' defined but not used
warning: 'mlxsw_pci_driver_name' defined but not used
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.20.8.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array msi_tgt_status is defined but never used, hence it is
redundant and can be removed.
Cleans up clang warning:
warning: 'msi_tgt_status' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix ptr_ret.cocci warnings:
drivers/net/ethernet/mellanox/mlxsw/spectrum_flower.c:543:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to enable/disable supported chips in be2net.
With disable support are removed coresponding PCI IDs and
also codepaths with [BE2|BE3|BEx|lancer|skyhawk]_chip checks.
Disable chip will reduce module size by:
BE2 ~2kb
BE3 ~3kb
Lancer ~10kb
Skyhawk ~9kb
When enable skyhawk only it will reduce module size by ~20kb
New help style in Kconfig
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main motive of this patch is to lay down driver's
tc offload infrastructure in place.
With these changes tc can offload various supported flow
profiles (4 tuples, src-ip, dst-ip, l4 port) for the drop
action. Dropped flows statistic is a global counter for
all the offloaded flows for drop action and is populated
in ethtool statistics as common "gft_filter_drop".
Examples -
tc qdisc add dev p4p1 ingress
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_ip 192.168.40.200 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto udp src_ip 192.168.40.100 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp src_ip 192.168.40.100 dst_ip 192.168.40.200 \
src_port 453 dst_port 876 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_port 98 action drop
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for dropping and redirecting
the flows based on destination IP in the packet.
This also moves the profile mode settings in their own
functions which can be used through tc flows in successive
patch.
For example -
ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.40.100 action -1
ethtool -N p5p1 flow-type udp4 dst-ip 192.168.50.100 action 1
ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.60.100 action 0x100000000
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for tc mqprio offload,
using this different traffic classes on the adapter
can be utilized based on configured priority to tc map.
For example -
tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3
This will cause SKBs with priority 0,1,2,3 to transmit
over tc 0,1,2,3 hardware queues respectively.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the bindings parsing for XGMAC2 IP block.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have all the XGMAC related callbacks, lets start integrating
this IP block into main driver.
Also, we corrected the initialization flow to only start DMA after
setting descriptors length.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC2 uses the same engine of timestamping as GMAC4. Let's use the same
callbacks.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MDIO related funcionalities for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the descriptor related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the DMA related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the MAC related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new entry to HWIF table for XGMAC 2.10. For now we fill it with
empty callbacks which will be added in posterior patches.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before MC-aware mode was enabled in commit 7b81953066 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"), only 8 traffic
classes were used. Under MC-aware regime, however, besides using TCs
0-7 for UC traffic, it additionally uses TCs 8-15 for BUM traffic. It
is therefore desirable to show counters for these TCs as well.
Update ethtool stats pool length, mlxsw_sp_port_get_strings() and
mlxsw_sp_port_get_stats() to include artifacts for all 16 TCs. For
consistency and simplicity, expose tc_no_buffer_discard_uc_tc for BUM
TCs as well, even though it ought to stay at 0 all the time.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_port_get_sset_count() is supposed to return the
total number of ethtool strings that mlxsw supports. Specifically for
names of statistic counters (the only string type that mlxsw supports
as of now), that number is stored in MLXSW_SP_PORT_ETHTOOL_STATS_LEN.
However, when adding RFC-2891 counters, that define wasn't updated to
include the new counters. As a result, ethtool snips out the counters
towards the end of the list, which contains per-TC counters, and only
the first three traffic classes end up being reported.
Fix by adding MLXSW_SP_PORT_HW_RFC_2819_STATS_LEN as appropriate.
Fixes: 1222d15a01 ("mlxsw: spectrum: Expose counters for various packet sizes")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent FW fixes a bug and allows to load newly flashed FW image after
reset. So make sure the reset happens after flash. Indicate the need
down to PCI layer by -EAGAIN.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware contains:
- Support for new types of cables
- Support for flashing future firmware without reboot
- Support for Router ARP BC and UC traps
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As recent spectrum FW imposes a limitation on using vlan_id key for
egress ACL, disallow the usage of that key accordingly and return a
proper extack message.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cond_resched() instead of usleep_range() to decrease the time
between polling attempts thus reducing overall driver load time.
Below is a comparison before and after the change, of loading eight
virtual functions.
Before:
real 0m8.785s
user 0m0.093s
sys 0m0.090s
After:
real 0m5.730s
user 0m0.097s
sys 0m0.087s
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_query_vport_state() and mlx5_modify_vport_admin_state() are used
only from within mlx5_core - unexport them.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_query_vport_admin_state() is not used anywhere. Remove it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused nvports argument.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify and query vport state commands share the same admin_state and
op_mod values, rename the enums to fit them both.
In addition, remove the esw prefix from the admin state enum as this
also applied for vnic.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware has defined new HCA capability field called "max_num_eqs",
that is the number of available EQs after subtracting reserved FW EQs.
Before this capability the FW reported the EQ number in "log_max_eqs",
the reported value also contained FW reserved EQs, but the driver might
be failing to load on 320 cpus systems due to the fact that FW
reserved EQs were not available to the driver.
Now the driver has to obtain max_num_eqs value from new FW to get real
number of EQs available.
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.
Fixes: b21f502f84 ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused netdev_registered_init/remove in en.h
Return ENOSUPPORT if the check MLX5_DSCP_SUPPORTED fails.
Remove extra white space
Fixes: 2a5e7a1344 ("net/mlx5e: Add dcbnl dscp to priority support")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current check relies on function BDF addresses and can get
us wrong e.g when two VFs are assigned into a VM and the PCI
v-address is set by the hypervisor.
Fixes: 5c65c564c9 ('net/mlx5e: Support offloading TC NIC hairpin flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Alaa Hleihel <alaa@mellanox.com>
Tested-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem below. The problem can be reproduced by the
following steps:
1) Connecting all HiNIC interfaces
2) On server side
# sudo ifconfig eth0 192.168.100.1 up #Using MLX CX4 card
# iperf -s
3) On client side
# sudo ifconfig eth0 192.168.100.2 up #Using our HiNIC card
# iperf -c 192.168.101.1 -P 10 -t 100000
after hours of testing, we will see errors:
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
hinic 0000:05:00.0: No MGMT msg handler, mod = 0
The errors are caused by the following problem.
1) The hinic_get_wqe() checks the "wq->delta" to allocate new WQEs:
if (atomic_sub_return(num_wqebbs, &wq->delta) <= 0) {
atomic_add(num_wqebbs, &wq->delta);
return ERR_PTR(-EBUSY);
}
If the WQE occupies multiple pages, the shadow WQE will be used. Then the
hinic_xmit_frame() fills the WQE.
2) While in parallel with 1), the free_tx_poll() checks the "wq->delta"
to free old WQEs:
if ((atomic_read(&wq->delta) + num_wqebbs) > wq->q_depth)
return ERR_PTR(-EBUSY);
There is a probability that the shadow WQE which hinic_xmit_frame() is
using will be damaged by copy_wqe_to_shadow():
if (curr_pg != end_pg) {
void *shadow_addr = &wq->shadow_wqe[curr_pg * wq->max_wqe_size];
copy_wqe_to_shadow(wq, shadow_addr, num_wqebbs, *cons_idx);
return shadow_addr;
}
This can cause WQE data error and you will see the above error messages.
This patch fixes the problem.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114813 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141440 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1384500 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357414 ("Missing break in switch")
Addresses-Coverity-ID: 1357415 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114811 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410181 ("Missing break in switch")
Addresses-Coverity-ID: 1410184 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1384501 ("Missing break in switch")
Addresses-Coverity-ID: 1398869 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410182 ("Missing break in switch")
Addresses-Coverity-ID: 1410183 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comments with
a proper "fall through" annotation, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 114809 ("Missing break in switch")
Addresses-Coverity-ID: 114810 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114808 ("Missing break in switch")
Addresses-Coverity-ID: 114802 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114796 ("Missing break in switch")
Addresses-Coverity-ID: 114804 ("Missing break in switch")
Addresses-Coverity-ID: 114806 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114801 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114800 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114799 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 200521 ("Missing break in switch")
Addresses-Coverity-ID: 114797 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114794 ("Missing break in switch")
Addresses-Coverity-ID: 114795 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114792 ("Missing break in switch")
Addresses-Coverity-ID: 114793 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114791 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114790 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114789 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114788 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114787 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114784 ("Missing break in switch")
Addresses-Coverity-ID: 114785 ("Missing break in switch")
Addresses-Coverity-ID: 114786 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114782 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114781 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114780 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114777 ("Missing break in switch")
Addresses-Coverity-ID: 114778 ("Missing break in switch")
Addresses-Coverity-ID: 114779 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114910 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 143135 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114878 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114891 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114889 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-08-07
This series contains updates to i40e and i40evf only.
Sergey cleans up a duplicate call to i40e_prep_for_reset() during
shutdown.
YueHaibing cleans up i40evf by removing code that was never being used
or called within the driver.
Jake updates the ethtool statistics to use a helper function since many
of the statistics use the same basic logic for copying strings into the
supplied buffer. Cleaned up the use of a local variable that is no
longer needed or used. Fixed additional stats issues, including the
failure to update the data pointer which was causing stats to be
reported incorrectly.
Mariusz fixes a bug where there was an oversight in configuring FEC when
link settings were forced which was causing 25G link to be configured
incorrectly.
Piotr adds a missing return code for when the firmware returns a busy
state. Also added the process to command firmware to start
rearrangement when switching between old NVM structure to the new flat
NVM.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE qps use a pair of physical queues (pq) received from the Queue Manager
(QM) - an offload queue (OFLD) and a low latency queue (LLT). The QM block
creates a pq for each TC, and allows RoCE qps to ask for a pq with a
specific TC. As a result, qps with different VLAN priorities can be mapped
to different TCs, and employ features such as PFC and ETS.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish not set offload_tc from offload_tc 0 and add getters and
setters.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API receives a priority and looks for the TC it is mapped to in the
operational DCBX configuration. The API returns QED_DCBX_DEFAULT_TC (0)
when DCBX is disabled.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For packets with computed IP/TCP/UDP checksum there is no need to tell
hardware to recompute it. For such kind of packets hardware expects the
packet to be at least 64 bytes and FCS to be computed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move checksum clearing outside of spinlock. The SKB is protected by
networking lock (HARD_TX_LOCK()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_tx_t return type for ndo_start_xmit function of macb driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print a string instead of the error code. Since there is a
possibility that the driver can recover, classify it as a
warning instead of an error.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When backing device firmware reports an error, it provides an
error ID, which is meant to be queried for more detailed error
information. Currently, however, an error ID is not provided by
the Virtual I/O server and there are not any plans to do so. For
now, it is always unfilled or zero, so request_error_information
will never be called. Remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All control commands (soft commands) goes through only Queue 0
(control and data queue). So only queue-0 needs post_lock,
other queues are only data queues and does not need post_lock
Added a flag to indicate the queue can be used for soft commands.
If this flag is set, post_lock must be acquired before posting
a command to the queue.
If this flag is clear, post_lock is invalid for the queue.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allocation of lmac->dmacs is not being checked for allocation
failure. Add the check.
Fixes: 3a34ecfd9d ("net: thunderx: add MAC address filter tracking for LMAC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike fs.val.lport and fs.val.fport, cxgb4_process_flow_match()
sets fs.val.{l,f}ip to net-endian values without conversion - they come
straight from flow_dissector_key_ipv4_addrs ->dst and ->src resp. So
the assignment in mk_act_open_req() ought to be a straight copy.
As far as I know, T4 PCIe cards do exist, so it's not as if that
thing could only be found on little-endian systems...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new layer for matching on geneve options. This allows
offloading filters configured to match geneve with options.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new push geneve option action. This allows offloading
filters configured to entunnel geneve with options.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of FLOW_DISSECTOR_KEY_ENC_IP to TC flower means that the ToS
and TTL of the tunnel header can now be matched on.
Extend the NFP tunnel match function to include these new fields.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TTL for encapsulating headers in IPv4 UDP tunnels is taken from a
route lookup. Modify this to first check if a user has specified a TTL to
be used in the TC action.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function accidentally failed to update the data pointer, which
caused the reported stats to be incorrect. Additionally, statistics
which follow queue stats in the output would potentially read non-zeroed
garbage data from the ethtool buffer.
This occurred because the data double pointer was not dereferenced
before incrementing the size.
Additionally, make sure this issue is more visible by adding a WARN_ONCE
to the i40e_get_ethtool_stats function. This warning will trigger
whenever the data pointer is not at the expected address, similar to the
check that we make in the i40e_get_stat_strings() function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During switching between old NVM structure approach (called structured
NVM) to new one (called flat NVM) or backward flash needs to be
rearranged to required NVM structure. This is a part of transition from
one NVM structure to another. The function is introduced to command
firmware to start rearrangement process.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Firmware can return a busy state, so the function return
I40E_ERR_NOT_READY.
Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 147e81ec75 ("i40e: Test memory before ethtool alloc succeeds")
code was added to handle ring allocation on systems with low memory.
It shadowed the ring parameter pointer by introducing a local ring
pointer inside the for loop. Most of the code in the loop already just
accessed the ring via &rx_rings[i]. Since most of the code already does
this, just remove the local variable.
If someone considers it worth keeping a local around, they should use it
for the whole section instead of just a couple of accesses.
This fixes a warning when -Wshadow is enabled
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit c61c8fe1d5 ("i40e: Implement an ethtool private flag to stop
LLDP in FW") added an extra for-loop which added a shadowing 'i'
variable as the index.
However, the local variable i already exists, and we already use it as
a loop index. Additionally, at this point, there is no further use of
the variable, so it's safe to simply overwrite the variable contents.
This fixes a -Wshadow warning which has started being enabled on some
distributions
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Patryk Malek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SYSTEMPORT MAC allows up to 8 filters to be programmed to wake-up
from LAN. Verify that we have up to 8 filters and program them to the
appropriate RXCHK entries to be matched (along with their masks).
We need to update the entry and exit to Wake-on-LAN mode to keep the
RXCHK engine running to match during suspend, but this is otherwise
fairly similar to Magic Packet detection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-08-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add cgroup local storage for BPF programs, which provides a fast
accessible memory for storing various per-cgroup data like number
of transmitted packets, etc, from Roman.
2) Support bpf_get_socket_cookie() BPF helper in several more program
types that have a full socket available, from Andrey.
3) Significantly improve the performance of perf events which are
reported from BPF offload. Also convert a couple of BPF AF_XDP
samples overto use libbpf, both from Jakub.
4) seg6local LWT provides the End.DT6 action, which allows to
decapsulate an outer IPv6 header containing a Segment Routing Header.
Adds this action now to the seg6local BPF interface, from Mathieu.
5) Do not mark dst register as unbounded in MOV64 instruction when
both src and dst register are the same, from Arthur.
6) Define u_smp_rmb() and u_smp_wmb() to their respective barrier
instructions on arm64 for the AF_XDP sample code, from Brian.
7) Convert the tcp_client.py and tcp_server.py BPF selftest scripts
over from Python 2 to Python 3, from Jeremy.
8) Enable BTF build flags to the BPF sample code Makefile, from Taeung.
9) Remove an unnecessary rcu_read_lock() in run_lwt_bpf(), from Taehee.
10) Several improvements to the README.rst from the BPF documentation
to make it more consistent with RST format, from Tobin.
11) Replace all occurrences of strerror() by calls to strerror_r()
in libbpf and fix a FORTIFY_SOURCE build error along with it,
from Thomas.
12) Fix a bug in bpftool's get_btf() function to correctly propagate
an error via PTR_ERR(), from Yue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The priority flow control statistics are laid out in the stats structure
using arrays. This made it unwieldy to use as part of an i40e_stats
array.
Add a new structure type, i40e_pfc_stats, and a helper function
i40e_get_pfc_stats which can return the stats for a given priority
value as an i40e_pfc_stats structure.
Use this to create an i40e_stats array, which we'll use to format and
copy the strings and stats into the supplied buffers.
This reduces even more boiler plate code in i40e_get_ethtool_stats and
i40e_get_stat_strings.
An alternative would be to modify the structure definition for the pfc
stats, but this is more invasive to the rest of the code base.
Note that a macro was used to setup the copy of stats from the
pf->stats, as this reduces the chance of typos in the code names. It
will produce a checkpatch.pl warning due to re-use of a macro argument.
In this case, it should be safe, as the macro will fail to compile in
cases where the argument is not a simple structure member name, and thus
arguments with side effects should not be an issue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VEB TC stats are currently implemented with separate parsing,
instead of using the i40e_stats array and associated helper functions.
This is likely because the stats rely on embedding the TC number into
the stat name.
Update i40e_add_stat_strings to take variadic arguments, and use these
to vsnprintf the i40e_stats string as a string containing format
specifiers.
Create a stats array for the VEB TC related stats,
i40e_gstrings_veb_tc_stats, and use this along with the helper functions
to remove the specialized boiler plate code.
Always call i40e_add_ethtool_stats for both this array and the general
VEB stats array. This ensures that we zero out any memory in case it was
not zero-allocated for us.
This ultimately results in less boiler plate code for the
i40e_get_stat_strings and i40e_get_ethtool_stats.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch configures FEC setting in i40e_force_link_state().
For some reason setting this field was overlooked thus causing
25G link to be configured incorrectly.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to the helper function to copy the ethtool stats strings, add
and use a helper function for copying the ethtool stats into the
supplied buffer.
Just like before, we use a macro to avoid having to pass ARRAY_SIZE
manually, so as to reduce chance of bugs.
Some of the stats, especially queue stats, are a bit trickier, and will
be handled in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the ethtool statistics use the same basic logic for copying
strings into the supplied buffer. A set of stats are stored in a const
array of i40e_stats structures, and we apply these all together.
Simplify the stats code by introducing a helper function which can take
a stats array and copy the strings into the buffer, updating the buffer
pointer as we go.
We use a macro to implement i40e_add_stat_strings so that ARRAY_SIZE can
be used on the array passed in. This ensures that we always use the
matching size in __i40e_add_stat_strings.
More complex stats currently do not use i40e_stats arrays, usually due
to custom formatted strings, or because the stats are not laid out in
the expected way. These stats will be updated to use the helper function
in separate future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are no in-tree callers.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function call to i40e_prep_for_reset() is duplicated in
i40e_shutdown routine and gets called before
i40e_enable_mc_magic_wake() which blocks it from being executed
correctly on system reboot or shutdown because adminq is already
disabled by first i40e_prep_for_reset() call.
Two register write calls are also duplicated.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The igb driver doesn't need anything provided by pci-aspm.h, so remove
the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
__inet6_lookup_established() expect th->dport passed in host-endian,
not net-endian. The reason is microoptimization in __inet6_lookup(),
but if you use the lower-level helpers, you have to play by their
rules...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to give unicast traffic precedence over BUM traffic, configure
multicast-aware mode on all ports.
Under multicast-aware regime, when assigning traffic class to a packet,
the switch doesn't merely take the value prescribed by the QTCT
register. For BUM traffic, it instead assigns that value plus 8.
ETS elements for TCs 8..15 thus need to be configured as well. Extend
mlxsw_sp_port_ets_init() so that it maps each of them to the same
subgroup as their corresponding TC from the range 0..7, such that TCs X
and X+8 map to the same subgroup.
The existing code configures TCs with strict priority. So far this was
immaterial, because each TC had its own subgroup. Now that two TCs share
a subgroup it becomes important. TCs are prioritized in order of 7, 6,
..., 0, 15, 14, ..., 8: the higher TCs used for BUM traffic end up being
deprioritized. Since that's what's needed, keep that configuration as it
is, and configure the new TCs likewise.
Finally in mlxsw_sp_port_create(), invoke configuration of QTCTM to
enable MC-aware mode on each port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures if the Switch Priority to Traffic Class mapping
is based on Multicast packet indication. If so, then multicast packets
will get a Traffic Class that is plus (cap_max_tclass_data/2) the value
configured by QTCT.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CNP CoS queue is reserved for internal RDMA Congestion Notification
Packets (CNP) and should not be used for a TC. Modify the CoS queue
discovery code to skip over the CNP CoS queue and to reduce
bp->max_tc accordingly. However, if RDMA is disabled in NVRAM, the
the CNP CoS queue can be used for a TC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the .ieee_setapp() and ieee_delapp() DCBNL methods to support
DSCP. This allows DSCP values to user priority mappings instead
of using VLAN priorities. Each DSCP mapping is added or deleted one
entry at a time using the firmware API. The firmware call can only be
made from a PF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export temperature sensor reading via hwmon sysfs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use latest firmware API to notify firmware about IF state changes.
Firmware has the option to clean up resources during IF down and
to require the driver to reserve resources again during IF up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags field is almost getting full. Move firmware capability flags
to a new fw_cap field to better organize these firmware flags.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect. Define a macro to perform
this check.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to collect live firmware coredump via ethtool.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the
firmware that the driver is compliant with the latest spec. With
that, the firmware can return expanded RSS profile IDs that the driver
checks to setup the proper gso_type for GRO-HW packets. But instead
of checking for the new profile IDs, we check the IP_TYPE flag
in TPA_START which is more straight forward than checking a list of
profile IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example The PF driver
will provision guaranteed minimum resources of 0. Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During hotplug, the driver's open function can be called almost
immediately after power on reset. The PHY may not be ready and the
firmware may return failure when the driver tries to update PHY
settings. Add retry logic fired from the driver's timer to retry
the operation for 5 seconds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to detect firmware support for external loopback and the extra
test entry for external loopback.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver gathers statistics using 2 mechanisms. Some stats are DMA'ed
directly from hardware and others are polled from the driver's timer.
Currently, we only adjust the DMA frequency based on the ethtool
stats-block-usecs setting. This patch adjusts the driver's timer
frequency as well to make everything consistent.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vnic_dev_register(), vnic_rq_alloc_bufs() and vnic_wq_alloc_bufs()
are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adjust_tail. There are no FW changes needed but add
a FW capability just in case there would be any issue with previously
released FW, or we will have to change the ABI in the future.
The helper is trivial and shouldn't be used too often so just inline
the body of the function. We add the delta to locally maintained
packet length register and check for overflow, since add of negative
value must overflow if result is positive. Note that if delta of 0
would be allowed in the kernel this trick stops working and we need
one more instruction to compare lengths before and after the change.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In previous patch mlxsw_afa_resource_del() was added to avoid a duplicate
resource detruction scenario.
For mirror actions, such duplicate destruction leads to a crash as in:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add a call to mlxsw_afa_resource_del() in
mlxsw_afa_mirror_destroy() in order to clear that resource
from rule's resources.
Fixes: d0d13c1858 ("mlxsw: spectrum_acl: Add support for mirror action")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each tc flower rule uses a hidden count action. As counter resource may
not be available due to limited HW resources, update _counter_create()
and _counter_destroy() pair to follow previously introduced symmetric
error condition handling, add a call to mlxsw_afa_resource_del() as part
of the counter resource destruction.
Fixes: c18c1e186b ("mlxsw: core: Make counter index allocated inside the action append")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ACL actions require the allocation of a separate resource
prior to applying the action itself. When facing an error condition
during the setup phase of the action, resource should be destroyed.
For such actions the destruction was done twice which is dangerous
and lead to a potential crash.
The destruction took place first upon error on action setup phase
and then as the rule was destroyed.
The following sequence generated a crash:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add mlxsw_afa_resource_del() as a complement of
mlxsw_afa_resource_add() to add symmetry to resource_list membership
handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the
_fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a
NOP.
Fixes: 140ce42121 ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum switch ACL action set is built in groups of three actions
which may point to additional actions. A group holds a single record
which can be set as goto record for pointing at a following group
or can be set to mark the termination of the lookup. This is perfectly
adequate for handling a series of actions to be executed on a packet.
While the SW model allows configuration of conflicting actions
where it is clear that some actions will never execute, the mlxsw
driver must block such configurations as it creates a conflict
over the single terminate/goto record value.
For a conflicting actions configuration such as:
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 \
action goto chain 100 \
action mirred egress mirror dev swp4
Where it is clear that the last action will never execute, the
mlxsw driver was issuing a warning instead of returning an error.
Therefore replace that warning with an error for this specific
case.
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper function to turn on/off MPD, this will be used to avoid
duplicating code as we are going to add additional types of wake-up
types.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already properly resume from Wake-on-LAN whether such a condition
occured or not, no need to process the WoL interrupt for functional
changes since that could race with other settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offset of msix number for roce is different between different
revision id. We should get it from firmware, instead of a fix value.
This patch refines the msix allocation, make it compatible.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The msix number for vf is different, depends on the max vf number.
Futherly if the vf supports roce, the offset of msix is not fixed.
It's incorrect to fix the msix number to 33. This patch fixes it by
querying the msix number from firmware, and adjusting it with roce
support.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the unregister_netdev flow for IPoIB no longer relies on external
code we can now introduce the use of priv_destructor and
needs_free_netdev.
The rdma_netdev flow is switched to use the netdev common priv_destructor
instead of the special free_rdma_netdev and the IPOIB ULP adjusted:
- priv_destructor needs to switch to point to the ULP's destructor
which will then call the rdma_ndev's in the right order
- We need to be careful around the error unwind of register_netdev
as it sometimes calls priv_destructor on failure
- ULPs need to use ndo_init/uninit to ensure proper ordering
of failures around register_netdev
Switching to priv_destructor is a necessary pre-requisite to using
the rtnl new_link mechanism.
The VNIC user for rdma_netdev should also be revised, but that is left for
another patch.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Denis Drozdov <denisd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Variables 'max_frm' and 'tmp_mac_key' are being assigned,
but are never used,hence they are redundant and can be removed.
fix fllowing warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:461:6: warning: variable 'max_frm' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1685:31: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:1855:41: warning: variable 'tmp_mac_key' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_info message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check DMA addressing limitations as suggested by the DMA API
how-to. This does not fix a particular issue seen but is
considered good style.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For FW_PORT_ACTION_GET_PORT_INFO32 messages, the
u.info32.lstatus32_to_cbllen32 is 32-bit Big Endian.
We need to translate that to CPU Endian in order to
test F_FW_PORT_CMD_DCBXDIS32.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning the command queue, the value of the HEAD register is not
in the range of next_to_clean and next_to_use, meaning that this value
is invalid. This also means that there is a hardware error and the
hardware will trigger a reset soon. At this time we should return an
error code instead of 0, and HCLGE_STATE_CMD_DISABLE needs to be set to
prevent sending command again.
Fixes: 3ff504908f ("net: hns3: fix a dead loop in hclge_cmd_csq_clean")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl setting controls whether packet priority should be updated
after forwarding. Configure RGCR.usp accordingly so that the device is
in sync with the kernel handling.
Note that RGCR doesn't allow changing arbitrary parameters
mid-operation, however "usp" is exempt and can be reconfigured.
Also react to NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE notifications
that signify change in this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boilerplate to schedule NETEVENT_IPV4_MPATH_HASH_UPDATE and
NETEVENT_IPV6_MPATH_HASH_UPDATE handling is almost equivalent to that of
NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE that's coming in the next
patch. The only difference is which actual worker function should be
called. Extract this boilerplate into a named function in order to allow
reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neterion was standalone for several years, then acquired by Exar and
shutdown in 11 months without ever making any new Exar branded adapters.
Users would probably think of them as Neterion and not Exar (as there
have been no follow-on adapters and the vast majority ever sold were
under the Neterion name).
6c541b4595 ("net: ethernet: Sort Kconfig sourcing alphabetically")
sorted Kconfig sourcing based on directory names, but in a couple cases,
the menu item text is quite different from the directory name and is not
sorted correctly:
drivers/net/ethernet/neterion/Kconfig => "Exar devices"
To address that and clear up any confusion about the name, "Exar" was
changed to "Neterion (Exar)" and the relevant entries in the Makefile
and Kconfig were reordered to match the alphabetical organization.
Inspired-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential execution path in which variable *err* is returned
without being properly initialized previously.
Fix this by initializing variable *err* to 0.
Addresses-Coverity-ID: 1472116 ("Uninitialized scalar variable")
Fixes: 0ec13877ce ("net/mlx5e: Gather all XDP pre-requisite checks in a single function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL won't work in PCI-based setups because we are not saving the PCI EP
state before entering suspend state and not allowing D3 wake.
Fix this by using a wrapper around stmmac_{suspend/resume} which
correctly sets the PCI EP state.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace ugly macroses on functions.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids that sparse complains about casts to restricted __be32.
Fixes: a3cdaa69e4 ("cxgb4: Adds CPL support for Shared Receive Queues")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In commit ab123fe071 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes: ab123fe071 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes: 472a1e44b3 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MTU helper function is used by both conventional mlx5e
instances (PF/VF) and the eswitch representors. The representor
shouldn't change the nic vport context MTU, the VF is responsible for
that. Therefore set_mtu_cb has a null value when changing the
representor MTU.
Fixes: 250a42b6a7 ("net/mlx5e: Support configurable MTU for vport representors")
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes: 106be53b6b ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes: a9f7705ffd ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Commit 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
forgot to return/free the xdp_frame in case the DMA mapping failed, correct this.
Also DMA unmap the frame in case mlx5e_xmit_xdp_frame() fails.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'app' is dereferenced before used for the devlink trace point.
In case FW is buggy and sends a control message to a VF queue
we should make sure app is not NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
There are no in-tree callers of cn23xx_dump_iq_regs.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since driver is devicetree-based, all device type and charateristic can be
determined by the compatible string and its data. It's unnecessary to
create another dependent function to check chip ID and then decide whether
the specific funciton is being supported on a certain device. It can be
totally replaced by the existing flag, so a cleanup is made by removing
the function and the only user, HWLRO.
MT2701 also have a missing HWLRO support in old code, so add it the same
patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve more in the existing code by reusing dma_zalloc_coherent instead
of dma_alloc_coherent with __GFP_ZERO or superfluous zeroing buffer.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Measuring UDP stream packet rate, single fully utilized TX core:
Radix Tree: 498,300 PPS
Hash Table: 555,468 PPS (11% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
-Saeed.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbW7KLAAoJEEg/ir3gV/o+YZ8H/2D4Ogav0zxQaNnw4ASYPpVA
luW1tvGUyk3C+fgbZO7tp/DETGJKbSodSMV9ZasEFFuHPft37mQaEIZf2rq58DvT
Q6vaaewyRCB6SzIGYjCZWtLI0aE5QtwMWDRbRBlRyQ0zUV6wr26W3WWWM2SpCJGK
zSuAF3Np0dEPTzBB566CY0nhYpsBiBXm2QJcgySL2WIx1nwQ6X8MJxjErhgQV+2L
1wVT6YTm1K2cdx9LsORt3FB/mFTQcOJCpl88AyhBB+pc7+i6pBtBp95tcqD8wmtF
dnMBmR+JzT108VxvcBnpwCxuVI7lLCcAs9hYITTGzUbo6rqT8xXV2HQ1KwU17Ow=
=tJj8
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-07-27' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-27 (Vxlan updates)
This series from Gal and Saeed provides updates to mlx5 vxlan implementation.
Gal, started with three cleanups to reflect the actual hardware vxlan state
- reflect 4789 UDP port default addition to software database
- check maximum number of vxlan UDP ports
- cleanup an unused member in vxlan work
Then Gal provides performance optimization by replacing the
vxlan radix tree with a hash table.
Measuring mlx5e_vxlan_lookup_port execution time:
Radix Tree Hash Table
--------------- ------------ ------------
Single Stream 161 ns 79 ns (51% improvement)
Multi Stream 259 ns 136 ns (47% improvement)
Measuring UDP stream packet rate, single fully utilized TX core:
Radix Tree: 498,300 PPS
Hash Table: 555,468 PPS (11% improvement)
Next, from Saeed, vxlan refactoring to allow sharing the vxlan table
between different mlx5 netdevice instances like PF and VF representors,
this is done by making mlx5 vxlan interface more generic and decoupling
it from PF netdevice structures and logic, then moving it into mlx5 core
as a low level interface so it can be used by VF representors, which is
illustrated in the last patch of the serious.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
